TP-LINK RM100 Router WiFi 4G LTE 300MBPS Manuel utilisateur

Taper
Manuel utilisateur

Ce manuel convient également à

RM100 User Manual
Federal Communication Commission Interference
Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/ TV technician for help.
FCC Caution
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
1 This device may not cause harmful interference.
2 This device must accept any interference received, including interference
that may cause undesired operation.
Note: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user’s
authority to operate the equipment.
FCC Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an uncontrolled
environment and it also complies with Part 15 of the FCC RF Rules.
This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20cm is maintained between the antenna
and users, and
2) The transmitter module may not be co-located with any other transmitter or antenna,
3) For all products market in US, OEM has to limit the operation channels in CH1 to
CH11 for 2.4Gband by supplied firmware programming tool. OEM shall not supply
any tool or info to the end-user regarding to Regulatory Domain change.
As long as 3 conditions above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for any
additional compliance requirements required with this module installed.
Canadian Compliance Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS
102 and compliance with RSS-102 RF exposure, users can obtain Canadian information
on RF exposure and compliance.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme
aux CNR d’Innovation, Sciences et Développement économique Canada applicables
aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes :
1) L’appareil ne doit pas produire de brouillage;
2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5
de RSS 102 et la conformité à l'exposition de RSS-102 rf, utilisateurs peut obtenir
l'information canadienne sur l'exposition et la conformité de rf.
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.
claration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies
pour un environnement non contrô. Cet équipement doit être installé et utilisé avec un
minimum de 20 cm de distance entre la source de rayonnement et votre corps.
IMPORTANT NOTE
In the event that these conditions can not be met (for example certain laptop
configurations or co-location with another transmitter), then the FCC authorization is no
longer considered valid and the FCC ID can not be used on the final product. In these
circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate FCC authorization.
End Product Labelling
The final end product must be labelled in a visible area with the following:
“Contains certifified FCC ID: 2AXJ4RM100”.
“Contains certifified IC: 26583-RM100”.
Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end user regarding
how to install or remove this RF module in the user’s manual of the end product which
integrates this module.
1. Overview
The RM100 Wi-Fi module provides a highly-integrated and flexible platform for
developing and evaluating products and applications based on the RTL8720CM-VT2
SoC. The RM100 Wi-Fi module can be either used with development kit for software
development or incorporated into OEM products to enable rapid deployment of Wi-Fi
connected systems.
The module includes the following components:
RTL8720CM-VT2 chip
An integrated Balun
4MB SPI Flash
Shield
2. Interface and pinout
Interface:
UART
Power supply
Pinout:
3. Electric Feature
Power Supply
Type
DC
Input
3.3V0.5A
Typical(11n iperf test mode)
587mW
Standby Mode
205mW
4. Mechanic Feature
Size: 18mm*23.5mm*3.9mm
5. Wireless Feature
Operating Frequency:2.4GHz:2412~2462MHz
Transfer Rate: 802.11b: 11/5.5/2/1 Mbps
802.11g: 54/48/36/24/18/9/6 Mbps
802.11n: up to 72.2 Mbps
Wireless Channel: ch1-ch11
Transimit Power:18.49dBm(max)
Antenna Type: external antenna with Ipex port
6. Physical and Environmental
Operating Temperature: 040
Storage Temperature: 040
Working Humidity: 10%90% RH
7. Additional Description
The module will be installed inside another device. And the outside of the device into
which the module is installed will display a label referring to the enclosed module.
This exterior label will use the wording such as Contains FCC ID: 2AXJ4RM100, or
any other similar wording that expresses the same meaning.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

TP-LINK RM100 Router WiFi 4G LTE 300MBPS Manuel utilisateur

Taper
Manuel utilisateur
Ce manuel convient également à