IKEA ESSENTIELL Manuel utilisateur

ES

FR

EN

ESSENTIELL

3

EN

CONTENTS

Important Safety Instructions 4

Introduction 5

Operating Instructions 6

Features at a Glance 6

Operating instructions 7

Preparing and Loading Dishes 10

Dishwasher Dispenser & Detergents 14

Factors Aecting Performance 15

Care and Cleaning 16

Before You Call 18

Limited Warranty 21

4

EN

IMPORTANT SAFETY INSTRUCTIONS

WARNING

This symbols will help alert you to such

dangers as personal injury, burns, re and

electrical shock.

WARNING

To reduce the risk of re, electrical shock or

injury when using your dishwasher, follow

the above basic precautions.

For your Safety

• Use your dishwasher only as instructed in

this User Manual.

• This Manual does not cover every possible

condition and situation that may occur.

Use common sense and caution when

installing, operating and maintaining any

appliance.

• NSF certied residential dishwashers

are not intended for licensed food

establishments.

• DISHWASHER MUST BE ELECTRICALLY

GROUNDED. Read the Installation

Instructions for details.

WARNING

Please read all instructions before using this

dishwasher.

• This dishwasher is designed to operate on

regular house current (120V, 60Hz). Use

a circuit equipped with a 15 ampere fuse

or circuit breaker. Use a 20 ampere fuse

if dishwasher is connected with a food

disposer.

• Do not operate dishwasher unless all

enclosure panels are in their proper place.

• To avoid entrapment and/or suocation,

remove door or door latch mechanism

from any dishwasher that is discarded or

not in use.

• Keep young children and infants away

from dishwasher when it is operating.

• Do not let children abuse, sit, stand or

play on door or racks of a dishwasher.

• Use only detergents and rinse agents

recommended for use in a dishwasher.

• Store dishwasher detergent and rinse

agents out of the reach of children.

• Do not wash plastic items unless marked:

“Dishwasher Safe” or equivalent. Check

with manufacturer for recommendations,

if not marked. Items that are not

marked dishwasher safe may melt and

create a potential re hazard.

• Disconnect electrical power to dishwasher

before servicing.

• If the dishwasher drains into a food

disposer, make sure disposer is completely

empty before running dishwasher.

• Repairs should be done by a qualied

technician.

• Do not tamper with controls.

• Do not touch the heating element during

or immediately after

• Use care unloading the dishwasher when

the Sanitize option has been selected.

Contents may be hot to the touch

immediately after the end of cycle.

• Water vapor from the vent may be hot to

the touch when the Sanitize option has

been selected. Use care and do not let

small children play around or touch the

vent area of the dishwasher.

• When loading items to be washed:

Locate sharp items and knives so

that they are not likely to damage

the door seal or tub.

Load sharp items and knives with

the handles up to reduce the risk

of cut-type injuries.

• Under certain conditions, hydrogen gas

may be produced in a hot water, system

that has not been used for 2 weeks or

more. HYDROGEN GAS IS EXPLOSIVE. If

hot water system has not been used for

such a period, before using dishwasher,

turn on for several minutes This will

release any accumulated hydrogen gas.

HYDROGEN GAS IS FLAMMABLE. Do no

smoke or use an open ame during this

time.

• Do not store or use combustible

materials, gasoline or other ammable

vapors and liquids in the vicinity of this or

any other appliance.

5

EN

INTRODUCTION

Thank you for choosing IKEA.

This User Manual is part of our commitment

to customer satisfaction and product quality

throughout the service life of your new

appliance.

We view your purchase as the beginning of a

relationship. To ensure our ability to continue

serving you, please use this page to record

important product information.

_________________________________

Purchase Date

_________________________________

Model Number

_________________________________

Serial Number



NOTE



Why Energy Ecient Units run long cycles:

Several factors are important to washing

dishware. The energy use of the dishwasher

was reduced by applying more of the factors

that don’t use so much energy and less of the

ones that use more. As a result, you will see

that the wash cycles take longer.



NOTE

The dishwasher is programmed to remember

your last cycle so you do not have to reset

each time. To start the dishwasher using

the same cycle and options selected on the

previous wash, just press the START/Cancel

pad.



Getting Started

1. Load Dishwasher (See Preparing and

Loading Dishes).

2. Add detergent (See Dishwasher Dispenser &

Detergents).

3. Add Rinse Aid, if needed (See Rinse Aid).

4. Select desired CYCLE (See Cycle Chart).

The indicator light will glow when selected.

5. Select desired OPTION (See Energy

Options).

The indicator light will glow when

selected.

6. Run hot water faucet nearest dishwasher

until water is at or near 120

0

F for optimal

performance (See Water Temperature). Turn

water o.

7. To start, press START/Cancel pad.

8. Close door to latch.

NOTE



Very Important Information - Read

Before Operating Your Dishwasher!

Normal Operating Sounds

This dishwasher does not sound like most

dishwashers - IT’S QUIETER.

Your Direct Feed Wash System dishwasher

uses energy ecient motors for the wash and

drain portions of the cycle you select. Each

cycle has a series of water lls and drains for

washing and rinsing dishes. As each cycle

begins, you may-or may not- hear the drain

motor. The next sound you will hear is the

splashing water as it enters the tub.

PLEASE BE ADVISED: If you compare

this dishwasher to previous models, you

may be surprised at what you DON’T

hear.



NOTE

Lights on the console will remain on once Lights on the console will remain on once

the door is shut and wash cycle begins. If it the door is shut and wash cycle begins. If it

is preferred to have the lights turn o while is preferred to have the lights turn o while

cycle is running see Console Lights section cycle is running see Console Lights section

for instructions.for instructions.





NOTE

If the dishwasher door is opened while the

unit is running, the START/Cancel pad must

be pressed and the door shut immediately

to return the unit to the selected cycle and

option, this must happen within 10 minutes

for the unit to continue the cycle.



6

EN

FEATURES AT A GLANCE

Heating Element

Glass Trap

Detergent

Dispenser

Overll Protector

Silverware Basket

Lower Rack

Serial Label

(Located on Right)

Top Rack

Nozzle or Spray Arm

(located inside the unit)

Cup Shelves

Middle Spray Arm

Lower Spray Arm

Rinse Aid

Your dishwasher cleans by spraying a mixture of hot water and detergent through the spray arms

against soiled surfaces. First, the dishwasher lls with water covering the lter area. Water is

then pumped through the spray arms. Soil particles go across the lter and down the drain as the

water is pumped out. This series of steps are repeated as needed. The number of water lls vary

with the cycle being used.

Bowl Tines

Wash Cycle Selections

Cycle times are approximate and will vary with Cycle times are approximate and will vary with

options selected. Hot water is necessary to options selected. Hot water is necessary to

activate dishwasher detergent and melt fatty activate dishwasher detergent and melt fatty

food soils. An automatic sensor will check food soils. An automatic sensor will check

the incoming water temperature and, if it is the incoming water temperature and, if it is

not hot enough, the cycle will be lengthened not hot enough, the cycle will be lengthened

for automatic water heating in the main wash for automatic water heating in the main wash

and nal rinse of all cycles. This happens and nal rinse of all cycles. This happens

even when Hi-Temp Wash option has not been even when Hi-Temp Wash option has not been

selected. Hi-Temp Wash is selected, an even selected. Hi-Temp Wash is selected, an even

higher temperature will be reached to handle higher temperature will be reached to handle

heavier soil loads.heavier soil loads.

OPERATING INSTRUCTIONS

Option Selections (available on

select Models)

Hi-Temp Wash Option

When Hi-Temp Wash option is selected, the When Hi-Temp Wash option is selected, the

dishwasher heats water in the main wash to dishwasher heats water in the main wash to

approximately 140approximately 140

oo

F (60F (60

oo

C).C).

This increase in water temperature helps the This increase in water temperature helps the

dishwasher detergent remove food grease and dishwasher detergent remove food grease and

soil from dishes more eectively and aids in soil from dishes more eectively and aids in

drying. Hi-Temp Wash option is available on drying. Hi-Temp Wash option is available on

Power Plus, Normal Wash and Top Rack cycles. Power Plus, Normal Wash and Top Rack cycles.

Hi-Temp Wash is automatically provided when Hi-Temp Wash is automatically provided when

the Power Plus cycle is selected.the Power Plus cycle is selected.

When Hi-Temp Wash option is selected, the When Hi-Temp Wash option is selected, the

indicator light will come on and remain on until indicator light will come on and remain on until

end of cycle. To turn o the Hi-Temp Wash end of cycle. To turn o the Hi-Temp Wash

option, press Hi-Temp Wash a second time. The option, press Hi-Temp Wash a second time. The

indicator light will turn o.indicator light will turn o.



NOTE

Lights on the console will remain on once Lights on the console will remain on once

the door is shut and wash cycle begins. If it the door is shut and wash cycle begins. If it

is preferred to have the lights turn o while is preferred to have the lights turn o while

cycle is running see Console Lights section cycle is running see Console Lights section

for instructions.for instructions.



7

EN

OPERATING INSTRUCTIONS

Sanitize Option

To sanitize your dishes and glassware, select To sanitize your dishes and glassware, select

the Sanitize option. When selected, the the Sanitize option. When selected, the

indicator light will come on and remain on until indicator light will come on and remain on until

the end of cycle. The water temperature in the the end of cycle. The water temperature in the

nal rinse will be raised to 156nal rinse will be raised to 156

oo

F (69F (69

oo

C). This C). This

option is available in Power Plus, Normal Wash option is available in Power Plus, Normal Wash

and Top Rack Cycles. Only these sanitization and Top Rack Cycles. Only these sanitization

cycles have been designed to meet NSF cycles have been designed to meet NSF

requirements.requirements.

The cycle time will be extended until the proper The cycle time will be extended until the proper

water temperature is reached. water temperature is reached.

Washing Washing

action will continue during the water heating action will continue during the water heating

delay. For best results, the incoming water delay. For best results, the incoming water

temperature should be at least 120temperature should be at least 120

oo

F (49F (49

oo

C).C).

The sanitize criteria may not be satised if there The sanitize criteria may not be satised if there

is an interruption of the cycle, power failure or if is an interruption of the cycle, power failure or if

the incoming water temperature is below 120the incoming water temperature is below 120

oo

F F

(49(49

oo

C).C).

To turn o the Sanitize option, press Sanitize a To turn o the Sanitize option, press Sanitize a

second time. The indicator light will turn o.second time. The indicator light will turn o.

Delay Start

The Delay Start option allows you to

automatically delay starting your dishwasher

1-24 hours.

To start the Delay Start option, press Delay

Start until the desired delay time shows in the

Status window. A light will come on indicating

the delay has been set and will remain on until

cycle starts. Press the START/Cancel pad to

start the delay option. If the delay option is

interrupted, the START/Cancel pad will have to

be pressed again to return to delay option.

To cancel the Delay Start option and to begin

the selected cycle before the delay period

is over, press and hold START/Cancel pad for

3 seconds.

Heat Dry/Air Dry

Use of the Heat Dry option, especially in Use of the Heat Dry option, especially in

combination with use of rinse agent, will combination with use of rinse agent, will

enhance drying. If Air Dry is selected the enhance drying. If Air Dry is selected the

heater will be de-activated during the drying heater will be de-activated during the drying

phase of the selected wash cycle. This will phase of the selected wash cycle. This will

slightly lower the energy use but will increase slightly lower the energy use but will increase

the likelihood that the dishware will not dry the likelihood that the dishware will not dry

completely.completely.

Child Lock Controls

To prevent children from accidently changing To prevent children from accidently changing

the dishwasher cycle or starting the the dishwasher cycle or starting the

dishwasher, to lock the dishwasher controls dishwasher, to lock the dishwasher controls

press and hold Delay Start for 3 seconds. An press and hold Delay Start for 3 seconds. An

indicator light on the lock graphic pad will indicator light on the lock graphic pad will

illuminate when the controls are locked and no illuminate when the controls are locked and no

new selections can be made until the lock is new selections can be made until the lock is

released. To unlock the controls, press Delay released. To unlock the controls, press Delay

Start again for 3 seconds, and the indicator Start again for 3 seconds, and the indicator

light will go out.light will go out.

To Cancel a Cycle

You can cancel a cycle anytime during the

cycle. Press and hold the START/Cancel pad

for 3 seconds. The light above the cycle and

option selected will go out, and the START/

Cancel light will remain illuminated, the

dishwasher will start a 90 second drain. At the

end of the drain, select the next desired cycle.

Favorite Cycle

The Favorite Cycle option allows you to The Favorite Cycle option allows you to

program your preferred cycle and options into program your preferred cycle and options into

one button. Once Programmed, simply select one button. Once Programmed, simply select

Favorite Cycle and then select START/Cancel.Favorite Cycle and then select START/Cancel.

To Program the Favorite Cycle:To Program the Favorite Cycle:

1. 1. Select your preferred cycle and optionsSelect your preferred cycle and options

2. 2. Press Favorite Cycle for 3 seconds.Press Favorite Cycle for 3 seconds.

The display will ash for 2 seconds The display will ash for 2 seconds

indicating the Favorite Cycle option has been indicating the Favorite Cycle option has been

programmed. To change the Favorite Cycle programmed. To change the Favorite Cycle

option simply repeat steps one and two option simply repeat steps one and two

above.above.

Max Dry

When Max Dry option is selected, the When Max Dry option is selected, the

dishwasher extends drying time by dishwasher extends drying time by

approximately 20 minutes. The Max Dry approximately 20 minutes. The Max Dry

option can be used with all cycles except China option can be used with all cycles except China

Crystal, Energy Saver, and Rinse Only. For best Crystal, Energy Saver, and Rinse Only. For best

drying performance, also apply an increased drying performance, also apply an increased

wash temperature by selecting Hi-Temp Wash wash temperature by selecting Hi-Temp Wash

or even better, the Sanitize option.or even better, the Sanitize option.

The energy required to use the Max Dry option The energy required to use the Max Dry option

costs pennies per cycle. You may choose not costs pennies per cycle. You may choose not

to select the Max Dry option; however you to select the Max Dry option; however you

may have items in your dish load that will not may have items in your dish load that will not

be completely dry at the end of the cycle.be completely dry at the end of the cycle.

8

EN

OPERATING INSTRUCTIONS

Overlay

Status Indicator Lights

Status Window

The STATUS window, available on some

models, indicates the following activity:

In the unlikely event that the dishwasher

malfunctions, displays the error code

“Uo”, or gives poor performance you can

call the IKEA Customer Care Center at

(833) 337-4006. They will be able to

provide assistance in troubleshooting the

problem and/or locating an authorized

service technician, if needed.

If it is desired to have the console lights

remain o while running, perform the following

operation: Prior to starting a cycle, press and

hold Power Plus and Rinse Only simultaneously

for approximately 8 seconds until the

corresponding lights ash. This will turn

the console lights o during cycle operation.

Simply repeat this operation to revert back to

the previous setting.

Console Lights

The console lights provide information about

the cycle selection and current status. During

operation, while the door is closed, these

lights will remain on. At the completion of

the cycle, the clean light will come on. The

sanitization light will also come on if that

option was selected and sanitization was

achieved during the wash cycle.

1H-24H............. Number of delay start

hours. The last hour

will count down in

minutes.

MINUTES.......... Number of minutes

left in cycle (1-199).

CLOSE DOOR.... Close door will scroll

one time in the status

window.

9

EN

OPERATING INSTRUCTIONS

Cycle and intended use Water per

Cycle

Power Plus*

Recommended for pots, pans,

casseroles and dinnerware hav-

ing light to heavily soiled loads.

7.3 - 9.6 gal.

28 - 36 L.

2 - 3½ Hours

Duration*

(approx.)

Normal Wash*

Recommended for lightly to

heavily soiled loads.

Quick Wash

Recommended for lightly

soiled loads only.

China Crystal

Recommended for lightly

soiled China, Crystal or other

delicate items.

Top Rack*

Recommended for small loads

in the upper rack only that are

light to heavily soiled.

Energy Saver*

Recommended for lightly

soiled loads.

Available Options

Pressure;

Temperature;

Drying

Scour, Surge; Sani-

tize, Hi-Temp; Max,

Heat, Air

Rinse Only

For rinsing dishware that will be

washed later.

Scour, Surge, Spray;

Sanitize, Hi-Temp,

Normal;

Max, Heat, Air

3.4 - 6.9 gal.

13 - 26 L.

1½ - 3 Hours

Surge;

Normal;

Max, Heat, Air

5.4 gal.

20 L.

34 Min.

(Air Dry Only)

Surge, Spray;

Normal;

Heat, Air

6.0 gal.

23 L.

1½ - 2 Hours

Surge; Sanitize,

Hi-Temp

Normal;

Max, Heat, Air

4.9 - 6.9 gal.

19 - 26 L.

1¼ - 3 Hours

Scour, Surge, Spray;

Normal;

Air

4.8 - 5.8 gal.

18 - 22 L.

1½ - 2 Hours

Surge 2.5 gal.

9 L.

16 Min.

(Air Dry Only)

The dishwasher checks the soil level on your dishes in the Power Plus, Normal Wash, Top Rack, The dishwasher checks the soil level on your dishes in the Power Plus, Normal Wash, Top Rack,

and Energy Saver Cycles. In response, automatic cycle adjustments are made to assure the and Energy Saver Cycles. In response, automatic cycle adjustments are made to assure the

dishware gets clean - with less food the cycle gets shorter. Cycle time will also vary based on dishware gets clean - with less food the cycle gets shorter. Cycle time will also vary based on

the options selected and the incoming water temperature. the options selected and the incoming water temperature. Not all cycles available on all Not all cycles available on all

models.models.

* Cycle uses Soil Sensing feature to determine best Wash performance.

Cycle and Option Chart

10

EN

PREPARING AND LOADING DISHES

Dish Preparation

Scrape away large pieces of food, bones,

pits, toothpicks, etc. The continuously

ltered wash uid will remove remaining

food particles. Burned-on foods should be

loosened before loading. Empty liquids from

glasses and cups.

Foods such as mustard, mayonnaise, vinegar,

lemon juice and tomato based products may

cause discoloration of stainless steel and

plastics if allowed to sit for a long period of

time. Unless the dishwasher is to be operated

at once, it is best to pre-rinse or use the Rinse

Only cycle to rinse o these food soils.

• Load racks so that large items do not

prevent the detergent dispenser from

opening.

• Check manufacturer’s recommendations

before washing items in question.

• If the dishwasher drains into a Food

Disposer, be sure disposer is

completely empty before starting

dishwasher.

Loading the Top Rack

Features and appearance of racks and

silverware basket as shown may vary

from your model.

The upper rack is designed for exibility in

loading a wide variety of items including cups,

glasses, stemware, small plates, bowls, etc.

Load glasses in top rack only. Damage may

occur if placed in bottom rack.

Load plastic items in top rack only. Melting

may occur if placed in bottom rack.

Load items with open ends facing down for

better cleaning and draining.

Damage may occur if delicate items touch

each other during dishwasher operation.

10 place settings standard loading pattern

12 place settings standard loading pattern

Some models have a fold-down cup shelf or

a cup shelf/stemware holder. They can be

used to load two levels of cups, juice glasses,

and other short items. Stagger items on

upper level so that water can reach all inside

surfaces. Fold up to load tall glasses.

Long-handled knives and utensils can be

placed in top rack.

Be sure nothing protrudes through the bottom

of the rack to block rotation of middle spray

arm.

11

EN

PREPARING AND LOADING DISHES

Bowl Tines

The bowl times oer the ultimate in exibility.

When closed, load with saucers or small

dishes. Open halfway and it is perfect for

small casserole dishes. Open completely for

those hard to t items. As you load your

dishwasher, you will nd many other ways to

use this unique feature.

Upper Rack

The Upper Rack cycle directs cleaning only to

items in the upper rack and can be used to

wash a wide assortment of items. It is useful

for washing partial loads - especially when the

upper rack lls up with glasses and the lower

rack is still empty.

STEMWARE HOLDER/CUPSHELF not

available on all models.

Adjustable Upper Rack

To raise the upper rack, refer to the gure

below.

Press the lever toward the center of the rack

and pull straight up on the rack.

Lever

To lower the upper rack, press the lever and

push down on the rack.

Place the clips of the cup shelf over the

horizontal rack wires and push down to attach

the cup shelf onto the second wire of the

upper rack.

12

EN

PREPARING AND LOADING DISHES

Features and appearance of racks and

silverware basket as shown may vary

from your model.

The lower rack is best for plates, saucers,

bowls, and cookware. Large items should be

placed along the edge so they do not block

the spray arm rotation. For best results, place For best results, place

bowls, casseroles, and sauce pans with soiled bowls, casseroles, and sauce pans with soiled

surface facing down and toward the center. surface facing down and toward the center.

Tilt slightly for better drainage.Tilt slightly for better drainage.

Spin the middle spray arm to make sure that

tall items do not block the rotation

Be sure pan handles do not protrude through

the bottom of the rack and block the lower

spray arm rotation.

Loading the Bottom Rack

10 place settings standard loading pattern.

12 place settings standard loading pattern

Fold-down Tines

The fold-down tines in the lower rack make

easy loading for those extra large and hard-to-

t items. The tines may be left up for normal

use or folded down for more exible loading.

Fold down for more space to load large pots

or pans.

13

EN

PREPARING AND LOADING DISHES

FPO

CAUTION

Load sharp items (knives, skewers, etc.)

pointing down.

Failure to do so may result in injury.

Features and appearance of racks and

silverware basket as shown may vary

from your model.

Load the silverware basket while it is in the

bottom rack or take the basket out for loading

on a counter or table.

For baskets with lids, small items like baby

bottle caps, jar lids, corn cob holders, etc., can

be placed in a covered section to hold them

in place.

Loading the Silverware Basket

Use suggested loading patterns, as shown, to

increase washability of the silverware.

Be sure nothing protrudes through bottom of

basket or rack to block the spray arm.

To avoid damaging the silver nish do not mix

silver and stainless.

When covers are up, mix items in each section

of the basket with some pointing up and some

down to avoid nesting. Water spray cannot

reach nested items.

To add or remove items after wash cycle

starts:

• Unlatch door and wait a few seconds

until wash action stops before opening.

• Add the item, move the door to a near-

closed position, and wait a few seconds

while the cold air slowly expands inside

the dishwasher.

• Close door rmly to latch and resume

cycle.

Adding a Dish

14

EN

DISHWASHER DISPENSER & DETERGENTS

Detergent Usage Chart

Cycle

Soft Water

(0-3 grains)

Medium Hard Water

(4-8 grains)

Hard Water

(9-12 grains)

Very Hard Water

(Over 12 grains)

Top Rack, Quick

Wash, China

Crystal or Energy

Saver

Rinse Only

2 teaspoons

(each cup-

1/4 full)

2 teaspoons

(Main Wash

cup-

1/4 full)

No Detergent

No Detergent No Detergent

(water softener

recommended)

5 teaspoons

(each cup- ll to line

above “Regular”)

5 teaspoons

(each cup- ll to line

above “Regular”)

8 teaspoons

(each cup-

completely full)

8 teaspoons

(Main Wash

cup- completely

full)

Each Cup-Com-

pletely Full (water

softener recom-

mended)

Main Wash Cup-

Completely Full

(water softener

recommended)

CAUTION

The use of industrial grade detergent can

damage the heating coil and other parts of

the dishwasher leading to damage to the

unit and surrounding property. Use only

household grade automatic dishwasher

detergents.

How much Detergent to use

The amount of detergent to use depends

on the water hardness. Water hardness is

measured in grains per gallon. Using too little

detergent can result in poor cleaning and hard

water lming or spotting. Using too much

detergent in soft water can cause etching

to some glassware which is surface damage

that appears like a lm but cannot be wiped

o. Your local water company, water softener

company or county extension agent can tell

you the water hardness in your area.

Heavy Wash,

Power Plus

or Normal

Wash

As a rule, use 1 teaspoon for each grain above 12. For very hard water, detergent alone

may not be enough and then a water softener is recommended to improve water quality and

dishwashing performance. However, when - using automatic dishwashing detergent tablets or

packets simply place one in the main wash cup.

• Use only fresh automatic dishwashing

detergent. Other detergents may cause

oversudsing.

• When using automatic dishwashing

detergent tablets or packets, use only

one tablet or packet, place in the main

wash cup and close.

• Add detergent just before starting cycle.

• Store detergent in a cool, dry location

and discard any that becomes moist or

caked.

Filing the Detergent Dispenser

The detergent dispenser has two detergent

cups. The smaller one is for addition to the

pre-wash and the larger is for release to the

main wash.

Cover

Main Wash

Cup

Cover

Latch

Pre-Wash

Cup

If the cover is closed on the Main Wash Cup

open by pressing the Cover Latch.

15

EN

FACTORS AFFECTING PERFORMANCE

IMPORTANT

Before starting a cycle, run hot water

to clear cool water from pipe.

Rinse Aid

Rinse aid greatly improves drying and Rinse aid greatly improves drying and

reduces water spots.reduces water spots. With it water “sheets”

o dishes rather than forming water droplets

that cling and leave spots.

A dispenser, located next to the detergent cup,

automatically releases a measured amount of

rinse aid during the last rinse. If spotting and

poor drying are problems, increase the amount

of rinse aid dispensed by rotating the dial to a

higher number. The dial is located under the

dispenser cap. The indicator will be dark when

full and will show clear when it is time to rell.

To add liquid rinse aid, turn dispense cap 1/4

turn counterclockwise and lift out. Pour in

rinse aid until liquid touches the indicated ll

level Replace cap.

Do not overll since this can cause

oversudsing. Wipe up any spills with a damp

cloth.

The dispenser holds enough for 35 to 140

washes, depending on the dial setting.

Water Temperature

Hot water is needed for best dishwashing and

drying results. Water entering dishwasher

should be at least 120

o

F (49

o

C) to give satis-

factory results.

To check water temperature entering dish-

washer:

• Turn on hot water faucet nearest dish-

washer for several minutes to clear cool

water from pipes.

• Hold a candy or meat thermometer in

the water stream to check the tempera-

ture.

• If temperature is below 120

o

F (49

o

C),

have a qualied person raise the hot

water heater thermostat setting.

The Heat Dry option in combination with The Heat Dry option in combination with

rinse aid will enhance drying perfor-rinse aid will enhance drying perfor-

mance. The energy required to use the mance. The energy required to use the

Heat Dry option costs pennies per cycle. Heat Dry option costs pennies per cycle.

You may choose not to select the Heat You may choose not to select the Heat

Dry option; however you will have items Dry option; however you will have items

in your dish load that will not be com-in your dish load that will not be com-

pletely dry at the end of the cycle.pletely dry at the end of the cycle.

Dispenser Opening Indicator

Dispenser Cap

Adjustable Setting

Water Pressure

The hot water line to dishwasher must provide

water pressure between 20 and 120 psi.

Low Water pressure may occur when laundry

or showers are in operation. If you experi-

ence poor wash performance you may need to

wait until water use is reduced before starting

dishwasher.

16

EN

CARE AND CLEANING

Outer Door - Clean outer door with warm

soapy water and a dishcloth or sponge. Rinse

with clean water and a dry cloth. Do not use

harsh cleaners.

Inside - Inside - The inside of the dishwasher and The inside of the dishwasher and

lter are self-cleaning with normal use. If lter are self-cleaning with normal use. If

needed, clean around the tub gasket area with needed, clean around the tub gasket area with

a damp cloth. The lter is self-cleaning. A a damp cloth. The lter is self-cleaning. A

glass trap located in the center of the lter glass trap located in the center of the lter

is designed to collect pieces of broken glass, is designed to collect pieces of broken glass,

straws, bones and pits.straws, bones and pits.



NOTE

Hard water may cause lime deposit buildup

on the interior of the dishwasher. For

cleaning instructions see “Removing Spots

and lm” section.

Overll Protector- keeps dishwasher

from overlling and is located in the left front

corner of the tub.

• Clean occasionally with household cleaner

containing vinegar or bleach to dissolve

any buildup.

• Overll Protector should move up and

down freely about one inch. If it does not

move, lift and clean underneath.



To empty the glass trap:

1. Grasp the glass trap’s handle and rotate it

90

0

clockwise while pressing down on the

center of the wash arm.

2. Grab the spray arm in the center and lift

the spray arm and glass trap assembly up

and out from the dishwasher.

3. Tip the assembly over an appropriate

container and tap it to empty the glass

trap.

OR, separate the glass trap - pull

the glass trap handle toward you, then

up, then further toward you to slide it

away from the rest of the assembly;

empty it into an appropriate container;

then slide the glass trap back into the

assembly.

4. Place the assembly back into position,

press down on the arm at the center

and rotate the glass trap handle 90

0

counterclockwise being sure the glass

trap ends in the orientation shown in the

image above. To avoid damage to

your unit make sure the spray arm

and glass trap are fully snapped in

place.

Spray Arm varies

by model

Glass Trap

Glass Trap Removal

(1)

(2)

(3)

WARNING

Burn Hazard

Allow heating element to cool before

cleaning the interior.

Failure to do so can result in burns.

17

EN

CARE AND CLEANING

CAUTION

Care of Drain Air Gap

If a drain air gap was installed for your built-in

dishwasher, check to make sure it is clean so

the dishwasher will drain properly. A drain air

gap is usually mounted on countertop and can

be inspected by removing the cover. This is

not part of your dishwasher and is not covered

by warranty.

Property Damage Hazard

Freezing temperatures may cause water

lines to rupture. Be sure all supply lines to

and circulating lines within dishwasher are

protected.

Failure to do so could result in property

damage.

NOTE

See Installation Instructions for more details

on disconnecting and restoring service to

your dishwasher.



Winterizing

A dishwasher left in an unheated place should

be protected from freezing. Have a qualied

person do the following:

To Disconnect Service:

1. Turn o electrical power to the

dishwasher at the supply source by

removing fuses or tripping circuit breaker.

2. Shut o water supply

3. Place a pan under the inlet valve.

Disconnect water line from inlet valve

and drain into pan.

4. Disconnect drain line from pump and

drain water into pan.

To Restore Service:

1. Direct water line discharge into a pan

and open the valve to ush the line.

2. Reconnect the water, drain, and

electrical power supply.

3. Turn on water and electrical power

supply.

4. Fill both detergent cups and run

dishwasher through a Heavy Wash/

Power Plus cycle.

5. Check connections to make sure they

do not leak.

18

EN

BEFORE YOU CALL

Before calling for service, review this

list. It may save you both time and

expense. This list includes common

experiences that are not the result of

defective workmanship or material in

your dishwasher.

Food Soils Left on Dishes

• Choose another cycle for longer washing

time.

• Check rack loading section for proper

loading-avoid nesting items.

• Home water pressure may be too low-

should be 20 to 120 pounds per square

inch (psi).

• Check incoming water temperature. It

should be about 120

o

F (49

o

C). (See

Factors Aecting Performance.)

• Check water hardness. For extremely

hard water, it may be necessary to install

a water softener. (See Detergent Chart).

• Use Fresh Detergent.

• Make sure items are not blocking the

spray arms, preventing them from

rotating.

• Do not overload the dishwasher (See

Preparing and Loading Dishes).

• Check to verify that the glass trap is

maintained and installed properly (See

Care and Cleaning).

Dishes not Dry

• Select heat or Max dry option.

• Make sure the rinse aid dispenser is lled.

• Increase the discharge setting of rinse

aid. (See Rinse Aid).

• Check the incoming water temperature.

Be sure it is at least 120

o

F (49

o

C).

• Check for proper loading-avoid nesting

items.

• Cups with a concave bottom will collect

water. Load them at the far left and right

of the upper rack so they will be held in a

tilted position.

Glassware/Flatware Spotted or Cloudy

• Check water hardness. For extremely

hard water, it may be necessary to install

a water softener. (See Detergent Chart).

• Water temperature may be low. Avoid

extremely low or high temperatures. (See

Factors Aecting Performance.

• Avoid overloading and improper loading.

(See Preparing and Loading Dishes).

• Use fresh detergent. Old detergent is

ineective.

• Make sure rinse aid dispenser is lled.

• Check to see that proper amount of

detergent is being used for cycle selected.

(See Detergent Dispenser).

• Home water pressure may be too low-it

should be 20 to 120 pounds per square

inch (psi).

• Containers, bowls, pots/pans, and any

dishware with concave surfaces that can

collect water should be placed in the rack

facing or angled down so that water is

able to drain even from the lowest point.

• Plastic items may need to be towel dried.

Dishware Chipped

• Load with care and do not overload. (See

Preparing and Loading Dishes).

• Place delicate items in top rack.

• Place glasses securely against pins and

not over pins.

• Load items so they are secure and don’t

jar loose when moving racks in and out.

Move racks in and out slowly.

• Make sure tall glasses and stemware will

clear top of tub when rack is pushed in.

• Fine antique china and crystal should be

hand-washed.

19

EN

BEFORE YOU CALL

Dishware Stained or Discolored

• Tea and coee can stain cups.

Remove the stains by hand washing in

a solution of 1/2 cup (120 ml) bleach

and one quart (1L) of warm water.

Rinse thoroughly.

• Iron deposits in water can cause a

yellow or brown lm. A special lter

installed in the water supply line will

correct this problem. (See Removing

Spots and Film).

• Aluminum utensils can leave gray/

black marks when they rub against

other items. Load Properly.

• Certain high acid foods can cause

discoloration of stainless steel and

plastics if allowed to sit for a long

period. Use the Rinse Only cycle

or rinse by hand if not operating

dishwasher at once.

• Mixing stainless steel and silver

utensils in silverware basket can cause

pitting of the stainless steel blades.

Avoid mixing stainless steel and silver.

Etching

• Using too much detergent especially in

soft or softened water causes damage

that looks like a lm but cannot be

removed.

• Adjust the amount of detergent based

on the water hardness. (Check Detergent

Chart).

• Lower the water temperature by selecting

one of the lower temperature options.

Detergent Left in Cups

• Detergent may be old. Discard and use

fresh detergent.

• Be sure the dish load doesn’t block spray

from entering the detergent cup.

• Check to see if cycle has been completed.

• Make sure items do not prevent the

detergent dispenser from opening.

Dishwasher Leaks

• Check that the door gasket is pressed

into its mounting channel, reaches to the

bottom of the tub and does not extend

beyond the end rib so as to interfere with

door closure.

• Spilled rinse aide can cause foam and

lead to overowing. Wipe up any spills

with a damp cloth.

• Check to see that the dishwasher is level.

(See Installation Instructions).

• Avoid oversudsing by using the correct

amount of detergent designed for

automatic dishwashers.

• Check to see that dishwasher is level.

(See Installation Instructions).

Water in Bottom of Tub

• Water left in the tub bottom after

the cycle is complete is not normal.

If water remains in the bottom of

the tub, the dishwasher may not be

draining properly. (See Dishwasher

Does not Drain Properly).

Cycle Takes a Long Time

• The cycle may have been automatically

lengthened to reach key temperatures

due to some factor such as a cool water

supply or a large load of dishes.

• Delay Start option may have been

selected.

• Choose lower temperature options to

shorten the cycle.

• Cycles that are soil-sensing adjust

automatically to assure a good wash

- heavier soils will elicit a longer cycle

response.

Vapor at Vent

• Spilled rinse aid can cause foam and

lead to overowing. Wipe up any spills

with a damp cloth.

Normal Sounds You Will Hear

• Normal sounds include water ll, water

spray, draining and motor sounds.

• There is a noticeable change in sound

when the wash action switches between

the lower and middle spray arm. This is

normal since each spray arm has its own

sound.

• It is normal for the dishwasher to pause

(no sound) when the wash action is

switching between the lower and middle

spray arms.

20

EN

BEFORE YOU CALL

Dishwasher Won’t Run

• Check to see if circuit breaker is tripped

or if a fuse is blown.

• Make sure water supply is turned on.

• Check to see if cycle is set correctly. (See

Operating Instructions).

• Is dishwasher set for Delay Start Option?

• Make sure START/Cancel pad is pressed

after cycle has been selected.

• Make sure door is closed and latched

immediately after pressing the START/

Cancel pad.

Dishwasher Won’t Fill

• Assure the water supply is turned on.

• Check that the overll protector moves up

and down freely. (See Overll Protector

section).

Dishwasher Does Not Drain Properly

• If unit is hooked up to a food waste

disposer, make sure the disposer is empty.

• Assure the knockout plug has been

removed from inside the food waste

disposer inlet.

• Assure the drain hose isn’t kinked.

• Make sure cycle is complete, not in a

pause.

• Assure the glass trap is maintained and

installed properly assuring no clogs (See

Care and Cleaning).

Dishwasher has an Odor

• Soiled dishes left in dishwasher too long

can create an odor. Use Rinse Only cycle.

• There will be a “new” smell when rst

installed. This is normal.

• Check to see if unit is draining properly.

(See Dishwasher Does Not Drain

Properly).

Removing Spots and Film

Hard water can cause lime deposit buildup

on the interior of the dishwasher. Dishes

and glasses may also get spots and lm for a

number of reasons. (See Glassware/Flatware

Spotted or Cloudy section). To remove

buildup, and lm, clean using the following

instructions:

1. Load clean dishes and glasses in normal

manner. Do not load any metal utensils

or silverware.

2. Do not add detergent.

3. Select the NORMAL WASH cycle. Press

START/Cancel pad. Close the door.

4. Allow dishwasher to run until it starts

the second water ll (approximately 8

minutes).

5. Open the door, pour 2 cups of white

vinegar into the bottom of dishwasher.

6. Press START/Cancel pad. Close the door

and allow cycle to nish.

Stains on Tub Interior

• Washing large amounts of dishware with

tomato based soil can cause a pink/

orange appearance. This will not aect

performance and will gradually fade over

time. Pre-rinsing or using the Rinse Only

cycle will reduce the chance of staining.

Using no heat dry option will lessen

staining.

Opening the door during cycle

• If the dishwasher door is opened while

the unit is running, the START/Cancel

pad must be pressed and the door shut

immediately to return the unit to the

selected cycle and option, this must

happen within 10 minutes for the unit to

continue the cycle.

La page charge ...

IKEA ESSENTIELL Manuel utilisateur

IKEA ESSENTIELL Manuel utilisateur

dans d''autres langues

Autres documents