Kichler Lighting 310204WCP Manuel utilisateur

INSTRUCTION MANUAL

Product images may vary slightly from actual product.

Cameron

™

KICHLER.COM

TABLE OF CONTENTS

SAFETY RULES ................................................................. 4

TOOLS AND MATERIALS REQUIRED ....................... 5

PACKAGE CONTENTS ....................................................5

MOUNTING OPTIONS .....................................................6

HANGING THE FAN ......................................................7-9

INSTALLATION OF SAFETY SUPPORT ..................10

MAKE THE ELECTRICAL CONNECTIONS .....11-12

FINISHING THE INSTALLATION................................12

ATTACHING THE FAN BLADES .................................13

INSTALLING THE LIGHT PLATE ............................... 13

INSTALLING THE LED LIGHT KIT .............................14

INSTALLING THE GLASS SHADE ..............................14

INSTALLING THE BATTERIES ....................................15

OPERATING INSTRUCTIONS ...............................16-17

INSTALLING THE COOLTOUCH™

CONTROL SYSTEM WALL PLATE ............................18

INSTALLING THE TRANSMITTER ............................19

TROUBLESHOOTING.............................................20-21

SPECIFICATIONS.............................................................21

FCC INFORMATION ...................................................... 22

3

Cameron

™

|

SAFETY RULES

1. To reduce the risk of electric shock, ensure electricity has been

turned o at the circuit breaker or fuse box before beginning.

2. All wiring must be in accordance with the National Electrical

Code and local electrical codes. Electrical installation should

be performed by a qualified licensed electrician.

3. WARNING: To reduce the risk of fire, electric shock, or

personal injury, use mounting screws provided with the

outlet box. Most outlet boxes commonly used for the

support of light fixtures are not acceptable for fan support

and may need to be replaced. Due to the complexity of the

installation of this fan, a qualified licensed electrician is

strongly recommended.

4. The outlet box and support structure must be securely

mounted and capable of reliably supporting a minimum of

50 pounds. Use only CUL Listed outlet boxes marked “FOR

FAN SUPPORT”.

5. The fan must be mounted with a minimum of 7 feet

clearance from the trailing edge of the blades to the floor.

6. Do not operate reversing switch while fan blades are in

motion. Fan must be turned o and blades stopped before

reversing blade direction.

7. Avoid placing objects in the path of the blades.

8. To avoid personal injury or damage to the fan and other

items, be cautious when working around or cleaning the fan.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR

PERSONAL INJURY, MOUNT FAN TO OUTLET BOX

MARKED “ACCEPTABLE FOR FAN SUPPORT”.

9. Do not use water or detergents when cleaning the fan or fan

blades. A dry dust cloth or lightly dampened cloth will be suitable

for most cleaning.

10. After making the electrical connections, spliced conductors should

be turned upward and pushed carefully up into outlet box. The

wires should be spread apart with the ground wire and white

(common) wire to one side with the black (load) wire to the other

side of the outlet box.

11. Electrical diagrams are reference only. Light kits that are not

packed with the fan must be CUL Listed and marked suitable for

use with the model fan you are installing. Switches must be CUL

General Use Switches. Refer to the Instructions packaged with the

light kits and switches for proper assembly.

WARNING

TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND

THE BLADE BRACKETS (ALSO REFERRED TO AS FLANGES)

DURING ASSEMBLY OR AFTER INSTALLATION. DO NOT INSERT

OBJECTS IN THE PATH OF THE BLADES.

SPECIAL NOTICE

This appliance is equipped with a “Wattage Limiting Device”

required by the United States Department of Energy. The

device has been installed at the factory and can not be removed.

Installing Lamps in excess of 75 total watts will disable the unit’s

light fixture. If this should happen, you will need to reset the

lighting fixture by turning the power o to the ceiling fan

and/or light fixture, reinstalling lamps totaling less that

75 watts and then turning the power back on.

4 | KICHLER.COM

TOOLS AND MATERIALS REQUIRED

PACKAGE CONTENTS

•

Phillips screwdriver

•

Blade screwdriver

•

11 mm wrench

•

Step ladder

•

Wire cutters

Unpack your fan and check the contents . You should have the following items:

A. Fan blades (5)

B. Canopy & Ceiling mounting bracket

C. Ball/downrod assembly

D. Coupling cover

E. Fan motor assembly

F. Set of 5 blade brackets and

Pre-Installed mounting screws

G. Light plate

H. Switch housing

I. Glass shade

J. CoolTouch

™

Receiver

K. Basic Function CoolTouch

™

Control System

L. Part bag contents

1) Mounting hardware:

wood screws (2), flat washers (2), star

washers (2), wire nuts (3), screws (2)

2) Blade attachment hardware :

screws (17), fiber washers (17)

3) Blade brackets hardware:

screws (2)

4) Safety cable hardware:

Wood screw, spring washer, flat washer

5) Balance kit

a

b

c

d

e

f

i

g

h

k

l

j

5

Cameron

™

|

MOUNTING OPTIONS

If there isn’t an existing UL (cUL for Canadian Installation) listed

mounting box, then read the following instructions. Disconnect the

power by removing fuses or turning o circuit breakers.

Secure the outlet box directly to the building structure. Use

appropriate fasteners and building materials. The outlet box and its

support must be able to fully support the moving weight of the fan

(at least 50 lbs). Do not use plastic outlet boxes.

Figures 1, 2 and 3 are examples of dierent ways to mount the

outlet box.

NOTE: If you are installing the ceiling fan on a sloped (vaulted)

ceiling, you may need a longer downrod to maintain proper

clearance between the tip of the blade and the ceiling. A minimum

clearance of 12” is suggested for optimal operation.

NOTE: Depending on the location you have selected for

installation, you may need to purchase and install a “Joist Hanger”

for the support of the outlet box. Make sure the joist hanger you

purchase has been designed for use with ceiling fans. (Fig. 4)

Outlet box

Fig. 1

Outlet box

Fig. 2

Fig. 3

Recessed

outlet box

Provide strong

support

Ceiling

mounting

plane

ANGLED CEILING

MAXIMUM 30° ANGLE

Fig. 4

Outlet box

6 | KICHLER.COM

HANGING THE FAN

REMEMBER to turn o the power before you begin. To properly install your ceiling

fan, follow the steps below.

Step 1. Remove the decorative canopy bottom cover from the canopy by turning

the cover counter clockwise. (Fig. 5)

Step 2. Remove the ceiling mounting bracket from the canopy by removing

(and save) one of the two screws. Loosen the remaining screw by a half turn.

(Fig. 5)

Step 3. Pass the 120 volt supply wires from the ceiling outlet box through the

center of the ceiling mounting bracket. (Fig. 6)

Step 4. Attach the ceiling mounting bracket to the outlet box using the screws

and washers included with the outlet box. (Fig. 6)

Step 5. Remove the hanger ball from the downrod assembly by loosening the set

screw, removing the cross pin and sliding the ball o the rod. (Fig. 7)

Fig. 5

Ceiling mounting bracket

Canopy

Canopy cover

Fig. 6

120V Wires

CUL Listed

outlet box

Washers

Hook

Mounting screws

(supplied with electrical box)

Ceiling

mounting

bracket

Fig. 7

Downrod

Set screw

Hanger ball

Cross pin

7

Cameron

™

|

HANGING THE FAN

Step 6. Loosen the two set screws and remove the hitch pin and retaining clip

from the coupling on top of the motor assembly. (Fig. 8)

Step 7. Carefully feed the electrical lead wires from the fan up through the

downrod. Thread the downrod into the coupling until the Hitch pin holes

are aligned.

Next, replace the hitch pin and retaining clip. Tighten both set screws. (Fig. 8)

Step 8. Slip the coupling cover, canopy cover and canopy onto the downrod.

Thread the hanger ball onto the downrod, insert the cross pin through the

downrod and tighten. Now tighten the set screw. (Fig. 9)

Fig. 9

Cross pin

Hanger ball

Downrod

Coupling

Coupling cover

Canopy cover

Canopy

PL-190B

Fig. 8

Supply wires

Coupling

Set screw

Retaining clipHitch pin

Downrod

8 | KICHLER.COM

HANGING THE FAN

Step 9. Lift the motor assembly into position and place the hanger ball into the

ceiling mounting bracket.

Rotate the entire assembly until the “Check Tab” has dropped into the

“Registration Slot” and seats firmly. (Fig. 10)

The entire motor assembly should not rotate (left or right) when seated properly.

WARNING: Failure to reattach the cross pin and seat the “Check Tab” can cause

the fan to fall from the ceiling during operation. Take special care to make sure this

pin is reattached.

Fig. 10

Check tab

Registration slot

9

Cameron

™

|

INSTALLATION OF SAFETY SUPPORT

(Required for Canadian installation ONLY)

A safety support cable is provided to help prevent the ceiling fan from falling,

please install it as follows.

Step 1. Attach the provided wood screw and washers to the ceiling joist next to the

mounting bracket but do not tighten. (Fig. 11)

Step 2. Adjust the length of the safety cable to reach the screw and washers by pulling the

extra cable through the cable clamp until the overall length is correct, put the end of the

cable back through the cable clamp, forming a loop at the end of the cable. Tighten the

cable clamp securely. Now, put the loop in the end of the safety cable over the wood screw

and under the washer. Tighten the wood screw securely.

NOTE: Although the safety support cable is required for Canadian installations only. It’s a

good idea to make the attachment with any installation.

Ceiling

mounting

bracket

Attach safety

cable to ceiling

joist with screw

and washer

Fig. 11

10 | KICHLER.COM

MAKE THE ELECTRIC CONNECTIONS

WARNING: To avoid possible electrical shock, be sure you have turned o the

power at the main circuit panel.

NOTE: In the Transmitter, Set Dip Switch #5 on the D position. This enables the

dimming function.

NOTE: The CoolTouch

™

Control System is equipped with 16 possible frequency

combinations to prevent interference from or with other remote control units.

The frequency switches on your receiver and transmitter have been preset at the

factory. Please recheck to make sure the switches on transmitter and receiver

are set to the same position, any combination of settings will operate the fan as

long as the transmitter and receiver are set to the same position. (Fig. 12)

Step 1. Insert the receiver into the ceiling mounting bracket with the flat side of

the receiver facing the ceiling. (Fig. 13) For best performance, make sure the Black

Antenna, on the end of the receiver, remains extended and not tangled with any

of the electrical wires.

Step 2. Motor to Receiver Electrical Connections: (Fig. 14) Connect the black wire

from the fan to the black wire marked “TO MOTOR L” on the receiver.

Fig. 13

ON

1 2 3 4

D

X

ON

Hanger

bracket

Receiver

Dip switch

Fig. 12

11

Cameron

™

|

MAKE THE ELECTRIC CONNECTIONS

FINISHING THE INSTALLATION

Connect the white wire from the fan to the white wire marked “TO MOTOR N” from the receiver.

Connect the blue wire from the fan to the blue wire marked “FOR LIGHT” from the receiver.

Secure all the wire connections with the plastic wire nuts provided.

Step 3. (Fig. 14) Receiver to House Supply Wires Electrical Connections: Connect the black

(hot) wire from the ceiling to the black wire marked “AC in L” from the receiver. Connect the

white(neutral) wire from the ceiling to the white wire marked “AC in N” from the Receiver. Secure

the wire connections with the plastic wire nuts provided.

Step 4. (Fig. 14) If your outlet box has a ground wire (green or bare copper) connect it to the fan

ground wires; otherwise connect the hanging bracket ground wire to the mounting bracket. Secure

the wire connection with a plastic nut provided. After connecting the wires, spread them apart so

that the green and white wires are on one side of the outlet box and black and blue wires are on the

other side. Carefully tuck the wire connections up into the outlet box.

NOTE: Fan must be installed at a maximum distance of 30 feet from the CoolTouch

™

Remote

Transmitter for optimal signal transmission between the transmitter and the fan’s receiving unit.

Step 1. Tuck all the connections neatly into the ceiling outlet box.

Step 2. Slide the canopy up to the mounting bracket and place one of the key hole slots over the

mounting screw on the mounting bracket. Rotate the canopy until the screw head locks in place at

the narrow section of the key hole. See figure 15.

Step 3. Align the remaining circular hole on the canopy with the remaining hole on the Ceiling

Mounting Bracket. Insert and tighten the mounting screw you removed earlier and the mounting

screw from Step 2 above. Now, attach the canopy cover to the mounting screw heads by inserting

the screw heads into the bottom side of the canopy cover and rotating the cover clockwise.

NOTE: Adjust the canopy screws as necessary until the canopy and canopy cover are snug. (Fig. 15)

Black (motor)

Blue (for light)

Receiver

Black (“to motor L”)

Black (“AC IN L”)

Black (hot)

Outlet box

(Connect to

ground wire on

hanger bracket if

no house ground

wire exists.)

Ground

(green)

White (“to motor N”)

White (“AC IN N”)

Green or bare

copper (ground)

White (neutral)

Screws

Ceiling

mounting

bracket

Outlet box

Fig. 15

Fig. 14

Blue (for light)

Canopy cover

Canopy

12 | KICHLER.COM

ATTACHING THE FAN BLADES

Step 1. Attach a blade to a blade bracket using the screws and rubber washers provided.

(Fig.16)

Make sure the blade is straight when set on the blade bracket. Tighten each mounting

screw and then repeat this procedure for each blade.

Step 2. Attach each blade assembly to the motor using the “Pre-Installed” mounting

screws in the blade bracket. (Fig 16)

INSTALLING THE LIGHT PLATE

Step 1. Loosen the two screws on the mounting ring attached to the motor shaft

and “remove” and save the third screw. (Fig. 17)

Step 2. Place the key hole slots on the light plate over the two screws previously

loosened on the mounting ring.

Turn the light plate until is locks in place at the narrow section of the key hole slots.

Tighten both key hole screws and replace the third screw previously removed and

tighten securely.

Mounting ring

Screws

Light plate

Screws

Rubber

washers

Blade brackets

Screws

Blades

Fig. 16

Fig. 17

13

Cameron

™

|

INSTALLING THE LED LIGHT KIT

INSTALLING THE GLASS SHADE

NOTE: Before continuing installation, confirm that the power is still turned o at the

main circuit breaker or by removing the correct fuse. Turning the power o using a

wall switch is not sucient to prevent electrical shock.

Step 1. Loosen the two mounting screws on the inside of the light plate then remove

and save the third screw.

Hold the LED light kit close to the light plate and connect the white wires from the

socket plate and the fan by pushing the connectors together. Follow the same

procedure with the black wire connectors. (Fig. 18)

Step 2. Tuck the connections neatly into the light plate. Place the key holes on the

LED light kit over the 2 screws previously loosened from the light plate, turn the

LED light kit until it locks in place at the narrow section of the key holes. Secure by

tightening all three screws. (Fig. 18)

Raise the glass shade against the LED light kit and turn clockwise until snug, DO

NOT OVER TIGHTEN. (Fig. 19)

LED Light kit

Wire connectors

Light plate

Screws

Glass

shade

LED Light kit

Fig. 19

Fig. 18

14 | KICHLER.COM

INSTALLING THE BATTERIES

Remove the battery compartment cover on the back of the CoolTouch

™

Transmitter and insert both batteries provided. Make sure the + sign is facing up.

Take care during this procedure NOT TO move the frequency dip switches inside this

compartment. The settings MUST remain the same as the settings on the receiver for

proper communication with the control system.

It’s a good idea to remove these batteries if your fan is not used for extend periods of

time, (months).

NOTE: Make sure Dip Switch #5 is set to the D position. This enables the dimming function.

ON

1 2 3 4

D

X

ON

Fig. 20

Code Switch

15

Cameron

™

|

OPERATING INSTRUCTIONS

Restore power to ceiling fan and test for proper operation.

A. , , and  buttons:

These three buttons are used to set the fan speed as follows:

 = High speed

 = Medium speed

 = Low speed

B.

button:

This button turns the fan o.

C. The “

” button: turns the light fixture On/O or controls dimming.

Press and release for On or O, Press and HOLD for full range dimming.

NOTE: As stated above, the light dimming function on this control is operated by

holding down the light button and releasing it at the desired brightness level.

This control system is NOT designed to “Reverse” the rotation of the blades. To set

the fan blades in reverse, the reverse slide switch is located on the top of the Motor

Housing. See Fig. 22

Do not operate reversing switch while fan blades are in motion. Fan must be turned

o and blades stopped before reversing blade direction.

Fig. 22

Fig. 21

Slide Switch

16 | KICHLER.COM

OPERATING INSTRUCTIONS

Speed settings for warm or cool weather depend on factors such as

the room size. Ceiling height, number of fans and so on.

Warm Weather Operation: Forward (counter clockwise) A downward

airflow creates a cooling eect as shown in Fig. 23. This allows you to

set your air conditioner on a warmer setting without aecting your

general comfort.

Cool Weather Operation: Reverse (clockwise). An upward airflow

moves warm air o the ceiling areas as shown in Fig. 24. This allows

you to set your heating unit on a cooler setting without aecting your

general comfort.

Fig. 23

Fig. 24

17

Cameron

™

|

INSTALLING THE COOLTOUCH

™

CONTROL SYSTEM WALL PLATE

NOTE: All wiring must be in accordance with the National Electrical

Code and local electrical codes. Electrical installation should be

performed by a qualified licensed electrician.

Select a location to install your CoolTouch

™

Control System

Transmitter. You can replace an existing wall switch or, install the

transmitter on ANY flat surface.

Option 1: Install the control system using an existing wall switch

outlet box. Make sure the electrical power is TURNED OFF at the

main panel before continuing.

NOTE: Switch installation must comply with all local and national

electric code.

Step 1. Remove the existing wall plate and the old switch from the

wall outlet box. Wire nut the BLACK leads (hot) together and push

back inside the outlet box. (Fig. 25)

Step 2. Install the metal plate and CoolTouch™ wall plate to the

existing wall outlet box with 4 screws provided. Then place the two

plastic plugs into the wall plate. (Fig. 26)

Option 2: Install the control system on ANY flat surface.

Select the desired location and use the CoolTouch

™

wall plate to

mark the location for the mounting holes. Use the dry wall anchors

and/or screws provided and finish the installation.

Metal plate

Outlet box

CoolTouch™ wall plate

Plastic plugs

Screws

Outlet box

Switch

Wall plate

Fig. 26

Fig. 25

18 | KICHLER.COM

INSTALLING THE TRANSMITTER

1. Insert the transmitter into the wall plate by inserting the bottom

of the transmitter first and then press the top of the transmitter into

the pocket. The transmitter will fully function from this location or

you can remove the transmitter and use as a “Hand Held” device.

2. To remove the transmitter from the wall plate, push the release

button and the transmitter will fall into your hand.

Release

button

Fig. 27

19

Cameron

™

|

TROUBLESHOOTING

Problem Solution

Fan will not start. 1. Check circuit fuses or breakers.

2. Check all electrical connections to ensure proper contact. CAUTION: Make sure the main

power is OFF when checking any electrical connection.

3. Make sure the transmitter batteries are installed properly. Positive (+) side facing out.

4. Ensure the batteries have a good charge.

Fan sounds noisy. 1. Make sure all motor housing screws are snug.

2. Make sure the screws that attach the fan blade brackets to the motor are tight.

3. Make sure wire nut connections are not rubbing against each other or the interior wall of the

switch housing. CAUTION: Make sure main power is o.

4. Allow a 24-hour “breaking-in” period. Most noise associated with a new fan disappear during

this time.

5. If using an optional light kit, make sure the screws securing the glassware are tight. Make sure

the light bulbs are not touching any other component.

6. Do not connect this fan to wall mounted variable speed control(s). they are not compatible

with ceiling fan motors or remote controls.

7. Make sure the upper canopy is a short distance from the ceiling. It should not touch the

ceiling.

20 | KICHLER.COM

La page charge ...

Kichler Lighting 310204WCP Manuel utilisateur

Kichler Lighting 310204WCP Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents