RIDGID 51402 Manuel utilisateur

Marque: RIDGID

Modèle: 51402

Catégorie: Outils électroportatifs

Taper: Manuel utilisateur

K-750 Drain Cleaning

Machine

• Français – 19

• Castellano – pág. 41

WARNING!

Read this Operator’s Manual

carefully before using this

tool. Failure to understand

and follow the contents of

this manual may result in

electrical shock, fire and/or

serious personal injury.

Drain Cleaner Manual

Table of Contents

Recording Form for Machine Serial Number ..............................................................................................................1

Safety Symbols ..............................................................................................................................................................2

General Safety Rules

Work Area Safety ........................................................................................................................................................2

Electrical Safety...........................................................................................................................................................2

Personal Safety ...........................................................................................................................................................2

Tool Use and Care ......................................................................................................................................................3

Service ........................................................................................................................................................................3

Drain Cleaner Warnings

Drain Cleaner Safety ...................................................................................................................................................3

Description, Specifications and Standard Equipment

Description ..................................................................................................................................................................4

Specifications ..............................................................................................................................................................4

Standard Equipment....................................................................................................................................................5

Machine Assembly ........................................................................................................................................................5

Connecting/Disconnecting

" and

" Drum Machine Cable Couplings .....................................................................6

Pre-Operation Inspection..............................................................................................................................................7

Machine and Work Area Set-Up ...................................................................................................................................9

Operating Instructions ................................................................................................................................................11

Operation...................................................................................................................................................................12

Feeding The Cable Into The Drain ............................................................................................................................12

Cleaning The Drain ...................................................................................................................................................13

Working The Blockage ..............................................................................................................................................13

Handling A Stuck Tool...............................................................................................................................................14

Freeing A Stuck Tool.................................................................................................................................................14

Retrieving The Cable.................................................................................................................................................14

Using Machine With A Front Guide Hose..................................................................................................................14

Adding Additional Cable ............................................................................................................................................15

Drum Removal and Installation .................................................................................................................................15

Maintenance Instructions ...........................................................................................................................................16

Cleaning ....................................................................................................................................................................16

Cables .......................................................................................................................................................................16

AUTOFEED...............................................................................................................................................................16

Lubrication.................................................................................................................................................................16

Front Guide Hose ......................................................................................................................................................16

Accessories .................................................................................................................................................................17

Machine Storage..........................................................................................................................................................17

Service and Repair ......................................................................................................................................................17

Disposal........................................................................................................................................................................18

Troubleshooting ..........................................................................................................................................................18

Lifetime Warranty..........................................................................................................................................Back Cover

*Original Instructions - English

K-750 Drain Cleaning Machine

Drain Cleaner

K-750 Drain Cleaning Machine

Record Serial Number below and retain product serial number which is located on nameplate.

Serial

No.

K-750 Drain Cleaning Machine

General Safety Rules

WARNING

Read and understand all instructions. Failure to fol-

low all instructions listed below may result in elec-

tric shock, fire, and/or serious injury.

SAVE THESE INSTRUCTIONS!

Work Area Safety

• Keep work area clean and well lit. Cluttered benches

and dark areas invite accidents.

• Do not operate power tools in explosive atmo-

spheres, such as in the presence of flammable

liquids, gases, or dust. Power tools create sparks

which may ignite the dust or fumes.

• Keep bystanders, children, and visitors away while

operating a power tool. Distractions can cause you to

lose control.

Electrical Safety

• Grounded tools must be plugged into an outlet

properly installed and grounded in accordance

with all codes and ordinances. Never remove the

grounding prong or modify the plug in any way. Do

not use any adapter plugs. Check with a qualified

electrician if you are in doubt as to whether the out-

let is properly grounded. If the tool should electrically

malfunction or break down, grounding provides a low

resistance path to carry electricity away from the user.

• Avoid body contact with grounded surfaces such

as pipes, radiators, ranges and refrigerators. There

is an increased risk of electric shock if your body is

grounded.

• Do not expose power tools to rain or wet condi-

tions. Water entering a power tool will increase the risk

of electric shock.

• Do not abuse the cord. Never use the cord to carry

the tool or pull the plug from an outlet. Keep cord

away from heat, oil, sharp edges or moving parts.

Replace damaged cords immediately. Damaged

cords increase the risk of electric shock.

• When operating a power tool outside, use an out-

door extension cord marked “W-A” or “W”. These

cords are rated for outdoor use and reduce the risk of

electric shock.

Personal Safety

• Stay alert, watch what you are doing and use com-

mon sense when operating a power tool. Do not

use a tool while you are tired or under the influence

Safety Symbols

In this operator’s manual and on the product, safety symbols and signal words are used to communicate important safety

information. This section is provided to improve understanding of these signal words and symbols.

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this

symbol to avoid possible injury or death.

DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.

WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

NOTICE indicates information that relates to the protection of property.

This symbol means read the operator’s manual carefully before using the equipment to reduce the risk of injury. The operator’s

manual contains important information on the safe and proper operation of the equipment.

This symbol means always wear safety glasses with side shields or goggles when handling or using this equipment to reduce

the risk of eye injury.

NOTICE

This symbol indicates the risk of hands, fingers or other body parts being caught, wrapped or crushed in the drain cleaning

cable.

This symbol indicates a risk of electrical shock.

DANGER

WARNING

CAUTION

This symbol indicates the risk of entanglement in a belt and pulley.

* The text used in the General Safety Rule section of this manual is verbatim, as required, from the applicable UL/CSA 745 1st edition standard. This section con-

tains general safety practices for many different types of power tools. Not every precaution applies to every tool, and some do not apply to this tool.

of drugs, alcohol or medication. A moment of inat-

tention while operating power tools may result in seri-

ous personal injury.

• Dress properly. Do not wear loose clothing or jew-

elry. Contain long hair. Keep your hair, clothing and

gloves away from moving parts. Loose clothes,

jewelry or long hair can be caught in moving parts.

• Avoid accidental starting. Be sure switch is OFF be-

fore plugging in. Carrying power tools with your finger

on the switch or plugging in power tools that have the

switch ON invites accidents.

• Remove adjusting keys or wrenches before turning

the tool ON. A wrench or a key left attached to a rotat -

ing part of the power tool may result in personal injury.

• Do not overreach. Keep proper footing and balance

at all times. Proper footing and balance enables bet-

ter control of the tool in unexpected situations.

• Use safety equipment. Always wear eye protec-

tion. Dust mask, non-skid safety shoes, hard hat, or

hearing protection must be used for appropriate condi-

tions.

Tool Use and Care

• Use clamps or other practical way to secure and

support the workpiece to a stable platform. Holding

the work by hand or against your body is unstable

and may lead to loss of control.

• Do not force the tool. Use the correct tool for your

application. The correct tool will do the job better

and safer at the rate for which it was designed.

• Do not use tool if the switch does not turn it ON and

OFF. Any tool that cannot be controlled with the switch

is dangerous and must be repaired.

• Disconnect the plug from the power source be-

fore making any adjustments, changing accessor-

ies, or storing the tool. Such preventive safety mea-

sures reduce the risk of starting the tool accidentally.

• Store idle tools out of the reach of children and

other untrained persons. Tools are dangerous in

the hands of untrained users.

• Maintain tools with care. Keep cutting tools sharp

and clean. Properly maintained tools with sharp cutting

edges are less likely to bind and are easier to control.

• Check for misalignment or binding of moving parts,

breakage of parts and any other condition that

may affect the tool’s operation. If damaged, have the

tool serviced before using. Many accidents are

caused by poorly maintained tools.

K-750 Drain Cleaning Machine

• Use only accessories that are recommended by the

manufacturer for your model. Accessories that may

be suitable for one tool, may become hazardous when

used on another tool.

Service

• Tool service must be performed only by qualified

repair personnel. Service or maintenance performed

by unqualified personnel could result in a risk of injury.

• When servicing a tool, use only identical replace-

ment parts. Follow instructions in the Maintenance

section of this manual. Use of unauthorized parts or

failure to follow Maintenance Instructions may create a

risk of electrical shock or injury.

Drain Cleaner Safety Warnings

WARNING

This section contains important safety information

that is specific to this tool.

Read these precautions carefully before using the K-

750 Drain Cleaning Machine to reduce the risk of

electrical shock or other serious personal injury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE!

Keep this manual with the machine for use by the operator.

Drain Cleaner Safety

• Only wear RIDGID

drain cleaning gloves or mitts

(“gloves”). Never grasp the rotating cable with

any thing else, including other gloves or a rag.

They can become wrapped around the cable, causing

hand injuries. Only wear latex or rubber gloves

under

RIDGID drain cleaner gloves. Do not use damaged

drain cleaning gloves.

• Never operate machine with the belt guard re-

moved. Fingers can be caught between the belt and

pulley.

• Do not allow the cutter to stop turning while the

machine is running. This can overstress the cable

and may cause twisting, kinking or breaking of the

cable. Twisting, kinking or breaking cable may cause

striking or crushing injuries.

• Keep gloved hand on the cable whenever the ma-

chine is running. This provides better control of the

cable and helps prevent twisting, kinking and breaking

of the cable. Twisting, kinking or breaking cable may

cause striking or crushing injuries.

• Position machine within three feet of the drain inlet

K-750 Drain Cleaning Machine

– Contact your local RIDGID distributor.

– Visit www.RIDGID.com or www.RIDGID.eu to find

your local RIDGID contact point.

– Contact Rudge Tool Technical Services Department at

[email protected], or in the U.S. and

Canada call (800) 519-3456.

Description, Specifications and

Standard Equipment

Description

The RIDGID

K-750 Drain Cleaning Machine will clean

drain lines 3" to 8" in diameter and 200 feet in length de-

pending on size of cable. Corrosion resistant cable drum

holds 100 feet of

" diameter cable or 125 feet of

" di-

ameter cable. Cable spins at 200 RPM.

The drum is belt-driven by a

HP electric motor that

has a grounded electrical system. An integral Ground

Fault Interrupter (GFCI) is built into the line cord. A pneu-

matic foot switch provides ON/OFF control of the motor. A

“kickstand” base is provided for machine stability during op-

eration.

The cable has a quick change coupling system for con-

necting or disconnecting tools. An optional AUTOFEED ad-

vances or retracts the cable at a rate up to 20 feet per

minute. A manual feed option is also available.

Specifications

Line Capacity ..................

See Following Chart

Drum Capacity...............100' of

" Cable or

125' of

" Cable

Motor Type ......................Induction

Motor Rating

115V Motor ..................115VAC Single Phase

6.5 A, 60Hz

230/240V Motor ...........230/240VAC

3.6 A, 50Hz, 550W

No Load Speed ...............200 r/min (RPM)

Weight (Machine Only)...95 lbs.

Dimensions

Length..........................26"

Width............................21"

Height ..........................43"

or properly support exposed cable when the dis-

tance exceeds three feet. Greater distances can

cause control problems leading to twisting, kinking or

breaking of the cable. Twisting, kinking or breaking

cable may cause striking or crushing injuries.

• One person must control both the cable and the

foot switch. If the cutter stops rotating, the operator

must be able to turn the machine motor off to prevent

twisting, kinking and breaking of the cable. Twisting,

kinking or breaking cable may cause striking or crush-

ing injuries.

• Do not operate the machine in REV (reverse) rota-

tion except as described in this manual. Operating

in reverse can result in cable damage and is used to

back the tool out of blockages.

• Keep hands away from rotating drum and guide

tube. Do not reach into drum unless machine is un-

plugged. Hand may be caught in the moving parts.

• Do not wear loose clothing or jewelry. Keep your

hair and clothing away from moving parts. Loose

clothing, jewelry or hair can be caught in moving parts.

• Always use appropriate personal protective equip-

ment while handling and using drain cleaning e -

quip ment. Drains may contain chemicals, bacteria

and other substances that may be toxic, infectious,

cause burns or other issues. Appropriate personal

protective equipment always includes safety glass -

es and RIDGID drain cleaning gloves, and may in-

clude equipment such as latex or rubber gloves, face

shields, goggles, protective clothing, respirators and

steel-toed footwear.

• Practice good hygiene. Use hot, soapy water to

wash hands and other body parts exposed to drain

contents after handling or using drain cleaning equip-

ment. Do not eat or smoke while operating or handling

drain cleaning equipment. This will help prevent con-

tamination with toxic or infectious material.

• Do not operate this machine if operator or ma-

chine is standing in water. Operating machine while

in water increases the risk of electrical shock.

• Only use drain cleaning machine to clean drains of

recommended sizes according to these instruc-

tions. Other uses or modifying the drain cleaning ma-

chine for other applications may increase the risk of

injury.

The EC Declaration of Conformity (890-011-320.10) will

accompany this manual as a separate booklet when re-

quired.

If you have any question concerning this RIDGID

product:

Cable Size Recommended Line

and Type Size and Reach

Line Size Reach

" Cable 3" to 6" 150'

" Cable 4" to 8" 200'

Figure 1 – K-750 Drain Cleaning Machine with AUTOFEED

Figure 2 – Machine Serial Number

The machine serial number is located on the rear drum

support. The last 4 digits indicates the month and year of

the manufacture. (04 = month, 10 = year).

Standard Equipment

All K-750 Drain Cleaning Machines come with one pair of

RIDGID Drain Cleaning Gloves.

This machine is made to clean drains. If prop-

erly used it will not damage a drain that is in good condi-

tion and properly designed, constructed and maintained.

If the drain is in poor condition, or has not been properly

designed, constructed and maintained, the drain cleaning

process may not be effective or could cause damage to

the drain. The best way to determine the condition of a

drain before cleaning is through visual inspection with a

camera. Improper use of this drain cleaner can damage

the drain cleaner and the drain. This machine may not

clear all blockages.

Machine Assembly

WARNING

To reduce the risk of serious injury during use, follow

these procedures for proper assembly.

FOR/OFF/REV switch should be OFF and machine un-

plugged before assembly.

Installing Handles

1. Remove the bolts and nuts retaining the belt guard

bracket to the machine frame, remove belt guard.

2. Loosely assemble loading wheel to handles with pro-

vided bolts

(see Figure 3)

Figure 3 – Handle Installation and Belt Guard Adjustment

K-750 Drain Cleaning Machine

Belt Guard

AUTOFEED

Guide Tube

Loading Wheel

Handles

FOR/OFF/REV

Switch

Foot Switch

Drum

Kickstand

Motor

GFCI Cord

NOTICE

Date Code

Loading Wheel

Belt Guard

Gap

1/4" MAX.

Handles

Belt Guard

Fasteners

3. Insert handles into machine frame and install bolts

through belt guard bracket, machine frame and han-

dle. Install nuts to retain bolts, do not tighten.

4. Firmly tighten bolts holding loading wheel to han-

dles.

5. Adjust gap between guard and drum to less than

". Firmly tighten belt guard bracket bolts. Confirm

that gap between belt guard and drum is less than

to prevent fingers and other objects from being pulled

into the belt and pulley. Adjust if necessary.

Installing Cable

Do not remove the bands or cables from the cable car-

ton. The cable is under tension and can whip or strike if

released.

Manual Cable Installation – this can be used for both

Manual and AUTOFEED units.

1. Retrieve male coupling end of cable through the

center hole of the carton and pull approximately 6' of

cable from the carton.

2. Connect the male coupling of the cable to the pigtail

coupling

(See Figure 4)

. Confirm connection is secure.

3. Pull short sections of cable from the carton and man-

ually feed into the drum. Do not turn machine ON.

AUTOFEED Cable Installation

1. Retrieve male coupling end of cable through center

hole of carton and pull cable from carton. Lay cable

out straight in a flat area (such as an empty paved

Connecting/Disconnecting

" and

" Drum Machine

Cable Couplings

Keep couplings clean and lubricated. Plunger pin must move freely and fully extend to secure connection.

New style – Plunger pin

Screwdriver required.

Connecting

1. Slide the couplings together. If needed, depress plunger

pin.

2. Confirm connection is secure. (plunger pin fully ex-

tended).

Disconnecting

1. Insert the screwdriver to depress the plunger pin.

2. Push the couplings apart until the male coupling con-

tacts the screwdriver.

3. Remove the screwdriver and push the couplings apart.

Old style – Rotating pin

Screwdriver required.

Connecting

1. Slide the couplings together.

2. Rotate pin so hash mark is away from end of cable (to-

wards “L” stamped on coupling). Confirm connection is

secure.

Disconnecting

1. Rotate pin so hash mark is towards end of cable (away

from “L” stamped on coupling).

2. Push the couplings apart.

3b2

Hash Mark

Figure 4

K-750 Drain Cleaning Machine

Pre-Operation Inspection

WARNING

Before each use, inspect your drain cleaning ma-

chine and correct any problems to reduce the risk of

serious injury from electric shock, twisted or broken

cables, chemical burns, infections and other causes

and prevent drain cleaner damage.

Always wear safety glasses, RIDGID drain cleaning

gloves, and other appropriate protective equipment

when inspecting your drain cleaner. For extra pro-

tection from chemicals and bacteria on the equip-

ment, wear latex, rubber or other liquid barrier

gloves under the RIDGID drain cleaning gloves.

1. Inspect the RIDGID drain cleaning gloves or mitts

(“gloves”). Make sure they are in good condition with

no holes, tears or loose sections that could be caught

in the rotating cable. It is important not to wear im-

proper or damaged gloves. The gloves protect your

hands from the rotating cable. If the gloves are not

RIDGID drain cleaning gloves or are damaged or

worn out, do not use machine until RIDGID drain

cleaning gloves are available.

See Figure 6.

Figure 6 – RIDGID Drain Cleaning Gloves – Leather, PVC

2. Make sure that the drain cleaning machine is un-

plugged and inspect the power cord, Ground Fault

Circuit Interrupter (GFCI) and plug for damage. If the

plug has been modified, is missing the grounding

prong or if the cord is damaged, to avoid electrical

shock, do not use the machine until the cord has

been replaced by a qualified repair person.

3. Clean any oil, grease or dirt from all equipment han-

dles and controls. This helps prevent the machine

or control from slipping from your grip.

parking lot or driveway) with no obstructions or items

that could become wrapped around the cable.

2. When using an AUTOFEED to load cable, the rotating

cable will tend to walk sideways. To prevent this,

place suitable stops (such as wood blocks) on either

side of the cable at 10 foot intervals.

3. After properly inspecting and setting up the drain

cleaner, attach the cable to the pigtail as shown in

Figure 4

. Make sure that no one is in the area around

the cable. Tighten the AUTOFEED knob so that the

roller touches the cable plus one additional turn. With

the FOR/OFF/REV switch in the FOR position, press

the foot switch to start the drum turning. Move the feed

handle in the opposite direction of the cable rotation to

feed the cable into the drum.

4. When 10' of cable is left outside of the drum, step off

the foot switch and move the FOR/OFF/REV switch to

OFF. Loosen the AUTOFEED knob and manually

feed the remaining cable into the drum. Do not use the

AUTOFEED to put all of the cable in the drum. The

cable end can whip around and cause serious injury.

Attaching Front Guide Hose (Optional Accessory

For Use With AUTOFEED)

1. Pull approximately 4' of cable from the drum.

2. Slide Front Guide Hose over the cable, adapter end

first. Pull plunger pin head up and place adapter over

the mounting collar on the AUTOFEED. Make sure

plunger pin locks into the hole in the mounting collar.

Figure 5 – Attaching Front Guide Hose To AUTOFEED

K-750 Drain Cleaning Machine

Plunger Pin

Hole

Guide Hose

4. Make sure the foot switch is attached to the drain

cleaning machine. Do not operate the machine with-

out the foot switch.

5. Inspect the drain cleaning machine for the following

items:

• Proper assembly and completeness

• Any broken, worn, missing, mis-aligned or binding

parts

• Smooth and free movement of the AUTOFEED

handle throughout range. Rotate the drum and

make sure that it turns freely without binding.

• Presence and readability of the warning label

(see

Figure 7)

• Presence and proper adjustment of the belt guard.

Belt guard should be adjusted so that the gap be-

tween the guard and the drum is no more than

(See Figure 3.)

• Any condition which may prevent safe and normal

operation.

If any problems are found, do not use the drain

cleaner until the problems have been repaired.

Figure 7 – Warning Label

6. Clean any debris from the cable and cutting tools.

Inspect cables for wear and damage. Inspect for:

• Obvious flats worn into the outside of the cable

(cable is made from round wire and the profile

should be round).

• Multiple or excessively large kinks (slight kinks up to

15 degrees can be straightened).

• Space between cable coils indicating that the cable

has been deformed by stretching, kinking, or running

in reverse (REV).

• Excessive corrosion from storing wet or exposure to

drain chemicals.

All of these forms of wear and damage weaken the

cable and make cable twisting, kinking or breaking

more likely during use. Replace worn and damaged

cable before using drain cleaner.

Make sure the cable is fully retracted with no more

than 6" of cable outside of the machine. This will

prevent whipping of the cable at start up.

7. Inspect the tools for wear and damage. If necessary,

replace prior to using the drain cleaning machine.

Dull or damaged cutting tools can lead to binding,

cable breakage, and slow the drain cleaning pro-

cess.

8. Make sure that the FOR/OFF/REV switch is set to the

OFF position.

9. With dry hands, plug cord into properly grounded

outlet. Test the GFCI provided in the electrical cord to

insure that it is operating correctly. When the test

button is pushed in, the indicator light should go off.

Reactivate by pushing the reset button in. If the indi-

cator light goes on, the GFCI is functioning properly.

If GFCI is not functioning properly, unplug the cord and

do not use the drain cleaning machine until the GFCI

has been repaired.

Figure 8 – Proper Drum Rotation (FOR Switch Position)

K-750 Drain Cleaning Machine

FORWARD

Drum

Rotation

10. Move the FOR/OFF/REV switch into the FOR posi-

tion. Press the foot switch and note the direction of ro-

tation of the drum. If the foot switch does not control

the machine operation, do not use the machine until

the foot switch has been repaired. The drum should

rotate counter-clockwise when viewed from the front

of the drum, and will match the drum direction s

hown

on the warning label (Figure 7) and shown in Figure 8.

Release the foot switch and let the drum come to a

complete stop. Place the FOR/OFF/REV switch into

the REV position, and repeat above testing to confirm

that the drain cleaner operates properly in reverse. If

the rotation is not correct, do not use the machine until

it has been repaired.

11. With the inspection complete, move the FOR/OFF/ -

REV switch into the OFF position and, with dry hands,

unplug the machine.

Machine and Work Area Set-Up

WARNING

Set up the drain cleaning machine and work area ac-

cording to these procedures to reduce the risk of in-

jury from electric shock, fire, machine tipping,

twisted or broken cables, chemical burns, infec-

tions and other causes, and prevent drain cleaner

damage.

Always wear safety glasses, RIDGID drain cleaning

gloves, and other appropriate protective equipment

when setting up your drain cleaner. For extra pro-

tection from chemicals and bacteria on the ma-

chine and in the work area, wear latex, rubber or

other liquid barrier gloves under the RIDGID drain

cleaning gloves. Rubber soled, non-slip shoes can

help prevent slipping and electric shock, especially

on wet surfaces.

1. Check work area for:

• Adequate lighting.

• Flammable liquids, vapors or dust that may ignite. If

present, do not work in area until sources have

been identified and corrected. The drain cleaner is

not explosion proof and can cause sparks.

• Clear, level, stable dry place for machine and oper-

ator. Do not use the machine while standing in wa -

ter. If needed, remove the water from the work area.

Wood or other coverings may need to be put down.

K-750 Drain Cleaning Machine

• Properly grounded electrical outlet. A three-prong or

GFCI outlet may not be properly grounded. If in

doubt, have outlet inspected by a licensed electri-

cian.

• Clear path to electrical outlet that does not contain

any potential sources of damage for the power

cord.

• Clear path to transport the drain cleaner to the work

area.

2. Inspect the drain to be cleaned. If possible, deter-

mine the access point(s) to the drain, the size(s) and

length(s) of the drain, distance to tanks or mainlines,

the nature of the blockage, presence of drain cleaning

chemicals or other chemicals, etc. If chemicals are pre-

sent in the drain, it is important to understand the

specific safety measures required to work around

those chemicals. Contact the chemical manufacturer

for required information.

If needed, remove fixture (water closet, etc.) to allow

access to the drain. Do not feed the cable through a

fixture. This could damage the drain cleaner and the

fixture.

3. Determine the correct drain cleaning equipment for

the application. The K-750 drain cleaner is made for:

• 3" to 6" lines up to 150' long with

" cable

• 4" to 8" lines up to 200' long with

" cable

Drain cleaners for other applications can be found

by consulting the the Ridge Tool Catalog, on line

at www.RIDGID.com or www.RIDGID.eu.

Inner-Core Cable is not recommended for use through

P-Traps and severe bends in lines smaller than 4".

Optional 24" flexible trap leaders can be added to aid

users through traps and tight clean-outs.

4. Make sure machine has been properly inspected.

5. If machine is equipped with an AUTOFEED, confirm

that the AUTOFEED is set to the proper size for the

cable being used

(see Figure 9)

. The slots in the

ends of the pins should align with the size of cable

being used. A screwdriver can be used to turn the

pins. The AUTOFEED adjustment knob may need to

be loosened to allow the size to be adjusted.

6. If needed, place protective covers in the work area.

The drain cleaning process can be messy.

K-750 Drain Cleaning Machine

Figure 9 – AUTOFEED Size Setting

7. Take the drain cleaning machine to the work area

along the clear path. If the machine needs to be

lifted, use proper lifting techniques. Use care moving

equipment up and down stairs, and be aware of pos-

sible slip hazards. Wear appropriate footwear to help

prevent slips.

8. Position the drain cleaning machine so that the K-750

cable outlet is within 3 feet of the drain access. Great -

er distances from the drain access increases the

risk of the cable twisting or kinking. If the machine

cannot be placed with the cable outlet within 3' of the

drain access, extend the drain access back to within

3' of the cable outlet with similar sized pipe and fit-

tings. Improper cable support can allow the cable to

kink and twist and can damage the cable or injure the

operator.

See Figure 10.

If using front guide hose,

place machine so that at least 6" of guide hose can be

placed in drain opening.

Figure 10 – Example of Extending Drain to Within 3' of

Cable Outlet

9. Tilt the machine forward and use your foot to rotate

one kickstand at a time to the backside of the wheel.

The machine should firmly rest on the kickstands.

The kickstands stabilize the machine and help prevent

tipping or walking during use. If working on soft ground,

it may be necessary to place wood or other solid ma-

terial under the drain cleaner for proper support.

Figure 11 – Setting Kickstands

10. Evaluate the work area and determine if any barriers

are needed to keep bystanders away from the drain

cleaner and work area. The drain cleaning process can

be messy and bystanders can distract the operator.

11. Select proper tool for the conditions.

If the nature of the obstruction is unknown, it is good

practice to use a straight or bulb auger to explore the

obstruction and retrieve a piece of the obstruction for

inspection.

Once the nature of the obstruction is known, an ap-

propriate tool can be selected for the application. A

good rule of thumb is to start by running the smallest

available tool through the blockage to allow the backed

up water to start flowing and carry away the debris and

cuttings as the drain is cleaned. Once the drain is open

and flowing, other tools appropriate for the blockage

can be used. Generally, the largest tool used should

be no bigger than the inside diameter of the drain

minus one inch.

Proper tool selection depends on the specific cir-

cumstances of each job and is left to the users’

judgement.

A variety of other cable attachments are available

and are listed in the Accessories section of this

manual. Other information on cable attachments

can be found in the RIDGID Catalog and on line at

www.RIDGID.com or www.RIDGID.eu.

AUTOFEED Size Setting

K-750 Drain Cleaning Machine

12. Securely install tool on the end of the cable

(See

Figure 4)

. If the connection is not secure, the cutting

tool may fall off in use.

13. Position the foot switch for easy accessibility. You

must be able to hold and control the cable, control the

foot switch, and reach the FOR/OFF/REV switch.

14. Confirm that the FOR/OFF/REV switch is in the OFF

position.

15. Run the cord along the clear path. With dry hands

plug the drain cleaner into a properly grounded outlet.

Keep all connections dry and off the ground. If the

power cord is not long enough, use an extension

cord that:

• Is in good condition.

• Has a three prong plug similar to that supplied on

the drain cleaner.

• Is rated for outdoor use and contains a W or W-A in

the cord designation (i.e. SOW), or complies with

H05VV-F, H05RN-F types or IEC type design

(60227 IEC 53, 60245 IEC 57).

• Has sufficient wire size (16 AWG (1.5mm

) for 50'

(15.2m) or less, 14 AWG (2.5mm

) for 50' – 100'

(15.2m – 30.5m) long). Undersized wires can over-

heat, melting the insulation or causing a fire or other

damage.

When using an extension cord, the GFCI on the

drain cleaner does not protect the extension cord. If

the outlet is not GFCI protected, it is advisable to

use a plug in type GFCI between the outlet and the

extension cord to reduce the risk of shock if there is a

fault in the extension cord.

Operating Instructions

WARNING

Always wear eye protection to protect your eyes

against dirt and other foreign objects.

Only wear RIDGID drain cleaning gloves or mitts.

Never grasp the rotating cable with anything else, in-

cluding a glove or a rag. They can become wrapped

around the cable, causing serious injury.

When cleaning drains that might contain hazardous

chemicals or bacteria, wear appropriate protective

equipment, such as goggles, face shields or respi-

rators, to prevent burns and infections. For extra pro-

tection from chemicals and bacteria on the ma-

chine and in the work area, wear latex, rubber or

other liquid barrier gloves under the RIDGID drain

cleaning gloves. Rubber soled, non-slip shoes can

help prevent slipping and electric shock, especially

on wet surfaces.

Follow operating instructions to reduce the risk of

injury from twisted or broken cables, cable ends

whipping around, machine tipping, chemical burns,

infections and other causes.

1. Make sure that machine and work area is properly set

up and that the work area is free of bystanders and

other distractions.

2. Pull cable out of drum and feed into drain. If needed,

loosen AUTOFEED knob. Push cable as far into drain

as it will go. At least one foot (.3 m) of cable must be

in drain so that the end of the cable will not come out

of the drain and whip around when the machine is

started.

Directly route the cable from the outlet of the machine

to the drain opening, minimizing exposed cable and

changes in direction. Do not tightly bend the cable –

this can increase the risk of twisting or breaking.

Figure 12 – In Operating Position, Manually Feeding

Cable

3. Assume a proper operating position:

• Be sure you can control the ON/OFF action of the

foot switch and can quickly release the foot switch

if needed. Do not press foot switch yet.

• Be sure that you have good balance, do not have to

over reach, and cannot fall on the foot switch, drain

cleaning machine, the drain or other hazards.

K-750 Drain Cleaning Machine

• You must be able to place at least one hand on the

cable at all times to control and support the cable.

• You must be able to reach the FOR/OFF/REV

switch.

This operating position will help to maintain control of

the cable and machine.

See Figure 12.

4. Move the FOR/OFF/REV switch to the FOR (FOR-

WARD) position. Do not depress the foot switch yet.

FOR/OFF/REV refers to the drum/cable rotation and

not to the direction of cable movement. Do not rotate

the cable in reverse except as specifically described

in these instructions. Running the drain cleaner in

REV can damage the cable.

Operation

The K-750 Drain Cleaning Machine is available in two

different feed configurations, either manual feed or AUTO -

FEED. A K-750 supplied with the AUTOFEED can either

feed the cable with the AUTOFEED (feed lever position) or

by manually pulling the cable from the drum and feeding it

into the drain. With the AUTOFEED you can switch back

and forth between operating methods as needed. A K-750

without the AUTOFEED can only be used manually.

Feeding The Cable Into The Drain

Manual Operation

Confirm that at least one foot (.3 m) of cable is in the drain.

Grasp the exposed cable with both gloved hands equally

spaced and pull 6"-12" of cable out of the drum so that

there is a slight bow in the cable. Gloved hands must be

on the cable to control and support the cable. Improper

cable support can allow the cable to kink or twist and can

damage the cable or injure the operator. Make sure that

the cable outlet of the drain cleaner is within 3' of the drain

opening.

Depress the foot switch to start the machine. The person

controlling the cable must also control the foot switch. Do

not operate the drain cleaner with one person controlling

the cable and another person controlling the foot switch.

This can lead to twisting, kinking and breaking of the

cable. Feed the rotating cable into the drain. The rotating

cable will work its way into the drain as you push on the

cable with gloved hands. Do not allow the cable to build up

outside the drain, bow or curve. This can allow the cable

to twist, kink or break.

When the cable has been fed into the drain opening,

pull 6"-12" more cable from the drum and continue feed-

ing the rotating cable into the drain.

AUTOFEED Operation

Confirm that at least one foot (.3 m) of cable is in the drain.

Tighten the AUTOFEED knob

(Figure13)

so that the roller

touches the cable plus one additional turn. Do no over-

tighten the knob – this can cause premature failure of the

AUTO FEED or cable.

Grasp near the center of the exposed length of cable

with a gloved hand. Gloved hand must be on the cable to

control and support the cable. Improper cable support can

allow the cable to kink or twist and can damage the cable

or injure the operator. Make sure that the cable outlet of

the drain cleaner is within 3' of the drain opening. Place the

other hand on the AUTOFEED lever. AUTOFEED lever

should be in neutral (Vertical) position

(see Figure 13).

See “Using Machine With A Front Guide Hose” if using a

guide hose.

Figure 13 – AUTOFEED Lever Positions

(Cable Turning In FOR Direction)

NOTE: Rate of cable advance or retrieve varies by

handle movement from neutral.

Depress the foot switch to start the machine. The person

controlling the cable must also control the foot switch. Do

not operate the drain cleaner with one person controlling

the cable and another person controlling the foot switch.

This can lead to twisting, kinking and breaking of the

cable. With the cable rotating, move the AUTOFEED

control handle in the same direction that the cable rotates.

This will cause the cable to feed out of the machine. The

further the control handle from the neutral position, the

faster the cable will be fed (up to 20' per minute, maxi-

mum). The rotating cable will work into the drain as you

control the cable with your gloved hand. Do not allow

the cable to build up outside the drain, bow or curve.

This can allow the cable to twist, kink or break.

Neutral

Full

Advance

Full

Retrieve

FOR

Rotation

AUTOFEED

Knob

K-750 Drain Cleaning Machine

Figure 14 – Operating the K-750 using the AUTOFEED

If it is difficult to get the cable through a trap or other fit-

ting, the following methods or combinations of methods

can be used.

• Sharp thrusts of the cable, both with and without

the cable rotating, can help the cable through a

trap.

• In some cases with the switch in the OFF position,

rotating the drum by hand can change the orien-

tation of the cutter to allow it to more easily ne-

gotiate the fitting.

• Run the drain cleaner in REV (REVERSE) rotation

for several seconds while pushing on the cable.

Only do this long enough to get the cable started

through the trap. Running the cable in reverse can

damage the cable.

• Use a flexible leader between the tool and the

cable.

• If these options don’t work, consider using a smaller

diameter or more flexible cable, or a different drain

cleaner.

Cleaning The Drain

As you feed the cable into the drain, you may see the

cable slow down or build up outside the drain. Always

keep your hands on the cable. You may feel the cable

start to wind or load up (this may feel like the cable is start-

ing to twist or squirm). This may be a transition in the drain

(trap, elbow, etc.), build up in the drain (grease, etc.) or the

actual blockage. Feed the cable slowly and carefully. Do

not let cable build up outside the drain. This can cause the

cable to twist, kink or break.

Pay attention to the amount of cable that has been fed into

the drain. Feeding cable into a larger drain, septic tank or

similar transition may cause the cable to kink or knot

and prevent removal from the drain. Minimize the amount

of cable fed into the transition to prevent problems. Each

wrap of the cable in the drum is approximately four feet

long. If using

" cable with a

" pigtail, do not feed the

connection through the AUTOFEED. This could damage

the AUTOFEED.

If an additional length of cable is needed,

see the section

“Adding Additional Cable”.

Working The Blockage

If the end of the cable stops turning, it is no longer clean-

ing the drain. If the end of the cable becomes lodged in the

blockage and power is maintained to the drain cleaner, the

cable will start to wind up (this may feel like the cable is

starting to twist or squirm). Having a hand on the cable al-

lows you to feel this wind up and control the cable. If the

cable end stops turning or if the cable starts to wind up, im-

mediately pull the cable back from the obstruction:

• Manual Operation – pull back on the cable to free

the cable end from the blockage.

• AUTOFEED Operation – move the feed lever in the

direction opposite the cable rotation to free the cable

end from the blockage.

Don’t keep the cable rotating if the cable is stuck in a

blockage. If the cable end stops turning and the drum

keeps rotating, the cable can twist kink or break.

Once the cable end is free of the blockage and turning

again, you can slowly feed the cable end back into the

blockage. Do not try to force the cable end through the

blockage. Let the spinning end “dwell” in the blockage to

completely break it up. Work the tool in this manner until

you have moved completely past the blockage (or block-

ages) and the drain is flowing. Manual operation is usually

the best choice if the cable repeatedly gets stuck when

using the AUTOFEED. If using an AUTOFEED machine

manually, the feed knob may need to be loosened, and

the feed lever placed in the neutral position.

While working the blockage, the cable and tool may be-

come clogged with debris and cuttings from the blockage.

This can prevent further progress. The cable and tool

need to be retrieved from the drain and the debris re-

moved.

See section on “Retrieving the Cable”

K-750 Drain Cleaning Machine

Handling A Stuck Tool

If the tool stops turning and the cable cannot be pulled

back from the blockage, immediately release the foot

switch while firmly holding the cable. Do not remove

hands from cable or cable may kink, twist and break. The

motor will stop and the cable and drum may turn back-

wards until the energy stored in the cable is relieved. Do

not remove hands from cable until the tension is re-

leased. Place FOR/OFF/REV switch in OFF position.

Freeing A Stuck Tool

If the tool is stuck in the blockage, with the FOR/OFF/-

REV switch in the OFF position and the foot switch re-

leased, try pulling the cable loose from the blockage. If

the tool will not come free from the blockage, place the

FOR/OFF/REV switch in the REV position. Grasp the

cable with both gloved hands, press the foot switch for

several seconds and pull on the cable until it is free of the

blockage. Do not operate the machine in the REV posi-

tion any longer than required to free the cutting tool

from the blockage or cable damage can occur. Place the

FOR/OFF/REV switch in the FOR position and con-

tinue cleaning the drain.

Retrieving The Cable

Once the drain is open, start a flow of water down the

drain to flush the debris out of the line. This can be

done by running a hose down the drain opening, turning

on a faucet in the system or other methods. Pay attention

to the water level, as the drain could plug again.

With water flowing through the drain, retrieve the cable

from the line. The flow of water will help to clean the

cable as it is retrieved. The FOR/OFF/REV switch should

be in the FOR position – do not retrieve the cable with the

switch in the REV position, this can damage the cable. As

with feeding the cable into the drain, cables can be caught

while being retrieved.

• Manual Operation – With both gloved hands equally

spaced on the exposed cable for control, pull 6"-12"

lengths of cable from the drain at a time and feed it

into the drum .

• AUTOFEED Operation – With one hand near the

center of the exposed length of cable, move the feed

lever in the direction opposite the cable rotation to

retrieve the cable. The rotating cable will work its way

out of the drain and back into the drum.

Continue retrieving cable until the cable end is just inside

the drain opening. Release the foot switch and allow the

machine to come to a complete stop. Do not pull the

end of the cable from the drain while the cable is rotating.

The cable can whip around and cause serious injury.

Pay attention to the cable during retrieval as the cable end

can still become stuck.

Place the FOR/OFF/REV switch in the OFF position.

Pull the remaining cable from the drain with gloved hands

and feed back into the drain cleaner. If needed, change

the tool and continue cleaning following the above pro-

cess. Several passes through a line are recommended for

complete cleaning.

Using Machine With A Front Guide Hose

The front guide hose is an optional accessory to help

protect fixtures and contain the liquid and debris thrown

off of the cable. It can only be used with an AUTOFEED.

Using the Front Guide hose can decrease feedback

from the cable, making it harder to tell what conditions

the cable is encountering. This may increase the pos-

sibility of damage to the cable. Using the front guide

hose makes it more difficult to switch back a forth be-

tween manual and AUTOFEED operation.

Using a machine with the front guide hose is similar to

using a machine with just the AUTOFEED. Follow in-

structions for AUTOFEED operation with the following

exceptions:

• When setting up the machine, insert the guide hose

at least 6" into the drain.

• Instead of holding the cable, hold the guide hose.

See Figure 15.

Always control the guide hose and

properly support the cable to prevent the cable from

twisting, kinking or breaking.

Figure 15 – Using Machine with Guide Hose

K-750 Drain Cleaning Machine

When using a front guide hose, pay attention how the

guide hose feels in your hand and watch the drum ro-

tation. Because the guide hose is over the cable, there

is less sensitivity to the loading of the cable, and it is

harder to tell if the tool is rotating or not. If the tool is not

rotating, the drain is not being cleaned.

If the tool continues to get hung up in the blockage, stop

using the AUTOFEED (leave the feed lever in the neu-

tral position) and work the cable manually. To do this, the

cable must be retrieved from the drain and the guide

hose removed to allow proper positioning of the machine

to the drain and access to the cable. Do not try to work the

cable by hand with the front guide hose in place.

When retrieving the cable, be sure to stop the cable be-

fore the tool is pulled into the end of the guide hose to

prevent damage.

Adding Additional Cable

If more cable is necessary to clean the drain than is

available in the machine drum, use the following pro-

cedures to add additional cable.

1. Make sure that the FOR/OFF/REV switch is in the

OFF position and the machine is unplugged.

2. Pull the cable connection from the drum. If using

the AUTOFEED, the feed knob may need to be loos-

ened.

3. Disconnect the cable from the pigtail and secure the

cable so it cannot slip down the drain.

4. If loading another cable in the existing drum, see

“Installing Cable” in the Assembly section.

5. Make sure that the drain cleaning machine is properly

set up. Attach the end of the cable in the drain to the

cable in the drum. Feed any excess cable back into

the drum.

6. Resume cleaning the drain. Make sure that the cable

is rotating and up to speed before feeding cable in.

Drum Removal and Installation

1. Make sure that the FOR/OFF/REV switch is in the

OFF position and the machine is unplugged.

2. If needed, remove AUTOFEED from machine by

unscrewing mounting bolt with

" wrench. Bolt and

AUTOFEED will come off as one.

See Figure 16.

Figure 16 – Removing AUTOFEED

3. Push down on motor table to release belt tension

and slip belt off of the drum.

See Figure 17.

Figure 17 – Releasing Belt Tension

Push Down

Motor Table

K-750 Drain Cleaning Machine

4. Use

" wrench to remove the bolt that holds the

drum to the machine frame.

See Figure 18.

Figure 18 – Removing Drum Bolt

5. Lay machine on it’s back

(see Figure 19)

. Use proper

lifting technique to lift the drum off of its mounting po-

sition. A drum with 100' of cable can weigh as much

as 150 pounds. In some cases, two people will be

needed to handle a drum of cable.

Figure 19 – Removing Drum

6. Reverse steps 2-5 to reassemble a drum to the K-750

frame. Exercise care when standing the machine

up to tighten the drum bolt.

Maintenance Instructions

WARNING

FOR/OFF/REV switch should be OFF and machine

unplugged before performing any maintenance.

Always wear safety glasses and RIDGID drain clean -

ing gloves and other appropriate protective equip-

ment when performing any maintenance.

Cleaning

The machine should be cleaned as needed with hot,

soapy water and/or disinfectants. Do not allow water to

enter motor or other electrical components. Make sure

unit is completely dry before plugging in and using.

Cables

Cables should be thoroughly flushed with water after

every use to prevent damaging effects of sediment and

drain cleaning compounds. Flush cable with water and

drain debris from drum by tipping machine forward after

every use to remove sediment, etc. which can corrode

cable.

To help prevent corrosion during storage, cables can be

coated with RIDGID Cable Rust Inhibitor. Once the cable

is clean and dry, pull the cable from the drum. While

manually feeding the cable back into the drum, wipe the

Cable Rust Inhibitor on the cable with a cloth.

Do not apply the Cable Rust Inhibitor to a rotating

cable. The cloth and your hand can become entangled in

the cable, and Cable Rust Inhibitor can be slung from ro-

tating cable.

AUTOFEED

After each use, hose out AUTOFEED assembly with

water and lubricate with lightweight machine oil.

Lubrication

Lubricate motor as per instructions on motor.

Lubricate machine with general purpose grease at

grease fitting (located at connection of guide tube and

drum) If drum is changed or removed, once a week if

used every day: once a month if used less.

Front Guide Hose

After use, flush the guide hose with water and drain.

When dry, a small amount of Cable Rust Inhibitor can be

placed in the guide hose to help keep it flexible.

K-750 Drain Cleaning Machine

5/8 (16mm)

3/4 (20mm)

Catalog Model

No. No. Description

43637 A-7558 Drum Assembly w/

⁄

" Pigtail

41982 A-7534 Drum Assembly w/

⁄

" Pigtail

43642 A-75 AUTOFEED Assembly

41992 C-100IC Kit w/Tools,

⁄

" x 100'

49032 Front Guide Hose Assembly

46015 E-453 Allen Wrench

41937 — RIDGID Leather Drain Cleaning Gloves

70032 — RIDGID PVC Drain Cleaning Gloves

59360 A-3 Tool Box

59987 Cable Rust Inhibitor 1 GAL.

31487 A-7570

⁄

" Repair Splicer

92805 A-6582

⁄

" Male Coupling

92810 A-6583

⁄

" Female Coupling

31492 A-7571

⁄

" Repair Splicer

92880 B-6840

⁄

" Male Coupling

92885 B-6841

⁄

" Female Coupling

Accessories

Inner Core (IC) Cables

Good flexibility and more cleaning power to the cable end.

Catalog Model

No. No. Description

92460 C-25 25' IC Cable (7.6m)

92465 C-26 50' IC Cable (15.2m)

92470 C-27 75' IC Cable (22.9m)

43647 C-24 100' IC Cable (30.5m)

92475 C-28 25' IC Cable (7.6m)

92480 C-29 50' IC Cable (15,2m)

41212 C-75 75' IC Cable (22.9m)

41697 C-100 100' IC Cable (30.5m)

5/8 (16mm)

3/4 (20mm)

Catalog Model

No. No. Description

32737 C-27HC 75' HC Cable (22.9m)

58192 C-24HC 100' HC Cable (30.5m)

47427 C-75HC 75' HC Cable (22.9m)

47432 C-100HC 100' HC Cable (30.5m)

Hollow Core Cables

Catalog Model

No. No. Description

92555 T-458

⁄

" x 2' Leader

92560 T-468

⁄

" x 2' Leader

44122 —

⁄

" Pigtail, 4

⁄

" Long

44117 —

⁄

" Pigtail, 6" Long

Leaders and Pig Tails

Accessories

WARNING

To reduce the risk of serious injury, only use ac-

cessories specifically designed and recommended

for use with the RIDGID K-750 Drain Cleaning Ma -

chine, such as those listed below. Other Ac ces -

sories suitable for use with other tools may be

hazardous when used with the K-750 Drain Clean -

ing Machine.

Tools and Replacement Blades – Fits 5/8" and 3/4"

Cables

Fits C-24, C-25, C-26, C-27, C-28, C-29, C-75, C-100, C-27HC,

C-24HC, C-75HC, and C-100HC

Catalog Model

No. No.

92485 T-403

92490 T-404

92495 T-406

92500 T-407

92505 T-408

51762 T-409

92510 T-411

92515 T-412

92520 T-413

92525 T-414

92530 T-416

92535 T-432

92540 T-433

92545 T-434

92550 T-436

Blade(s)

92835

92840

92850

—

92890

—

92815

92820

92825

92830

92855

92860

92865

92870

92875

Holder

92900

92915

—

92915

—

92905

92910

92895

Description

P-Trap Cutter, 3"

P-Trap Cutter, 3

Spear Blade, 1

Retrieving Auger, 2

Sawtooth Cutter, 3"

H-D Bulb Auger, 1

Double Cutter, 2"

Double Cutter, 2

Double Cutter, 3"

Double Cutter, 4"

Double Cutter, 6"

3-Blade Cutter, 2"

3-Blade Cutter, 3"

3-Blade Cutter, 4"

3-Blade Cutter, 6"

Replacement

Machine Storage

The drain cleaner and cables must be

kept dry and indoors or well covered if kept outdoors. Store

the machine in a locked area that is out of reach of chil-

dren and people unfamiliar with drain cleaners. This ma-

chine can cause serious injury in the hands of untrained

users.

Service and Repair

WARNING

Improper service or repair can make machine un-

safe to operate.

The “Maintenance Instructions” will take care of most of

the service needs of this machine. Any problems not ad-

dressed by this section should only be handled by an au-

thorized RIDGID service technician.

Tool should be taken to a RIDGID Independent Author -

ized Service Center or returned to the factory.

WARNING

K-750 Drain Cleaning Machine

Cable kinking or breaking.

Drum stops while foot

switch is depressed.

Re starts when foot

switch is re-depressed.

Drum turns in one direc-

tion but not the other.

Ground Fault Circuit Inter -

rupter trips when ma chine

is plugged in or when foot

pedal is depressed.

Motor turning but drum

is not.

AUTOFEED doesn’t work.

Machine wobbles or

moves while cleaning

drain.

Cable is being forced.

Cable used in incorrect pipe diameter.

Motor switched to reverse.

Cable exposed to acid.

Cable worn out.

Cable not properly supported.

Hole in foot switch or hose.

Hole in air switch.

Faulty FOR/OFF/REV switch.

Damaged power cord.

Short circuit in motor.

Faulty Ground Fault Circuit Interrupter.

Moisture in motor, switch box or on plug.

Belt slipping because cable is being forced.

Belt not on drum or pulley.

AUTOFEED full of debris.

AUTOFEED needs lubrication.

AUTOFEED not set properly for cable size.

Cable not evenly distributed.

Kickstands are not on ground.

Ground not level/stable.

Do Not Force Cable! Let the cutter do the work.

Use correct cable for pipe.

Use reverse only if cable gets caught in pipe.

Clean and oil cables routinely.

If cable is worn, replace it.

Support cable properly, see instructions.

Replace damaged component.

If no problem found with pedal or hose, replace

diaphragm switch.

Replace switch.

Replace cord set.

Take unit to authorized service center.

Replace cord set that includes a Ground Fault

Circuit Interrupter.

Take drain cleaner to an Authorized Service Center.

Do not force cable.

Re-install belt.

Clean AUTOFEED.

Lubricate AUTOFEED.

Properly set AUTOFEED, see instructions.

Pull all cable out and refeed in, evenly distribute.

Move kickstands to use position.

Place on level stable surface.

PROBLEM POSSIBLE REASONS SOLUTION

Chart 1 Troubleshooting

For information on your nearest RIDGID Independent

Service Center or any service or repair questions:

• Contact your local RIDGID distributor.

• Visit www.RIDGID.com or www.RIDGID.eu to find

your local RIDGID contact point.

• Contact Ridge Tool Technical Services Department at

[email protected], or in the U.S. and

Canada call (800) 519-3456

Disposal

Parts of the K-750 drain cleaner contain valuable materials

and can be recycled. There are companies that specialize

in recycling that may be found locally. Dispose of the

com ponents in compliance with all applicable regula-

tions. Contact your local waste management authority

for more information.

For EC Countries: Do not dispose of elec-

trical equipment with household waste!

According to the European Guideline 2002/ -

96/ EC for Waste Electrical and Electronic

Equip ment and its implemen tation into nation -

al le g is lation, electrical equipment that is no

longer usable must be collected separately and disposed

of in an environmentally correct manner.

La page charge ...

RIDGID 51402 Manuel utilisateur

Marque: RIDGID

Modèle: 51402

Catégorie: Outils électroportatifs

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: RIDGID 51402 User manual
español: RIDGID 51402 Manual de usuario

RIDGID 51402 Manuel utilisateur

RIDGID 51402 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents