Simplicity 040248-0 Manuel utilisateur

7KW DUAL-MODE BACKUP GENERATOR

Operator’s Manual

Manual del Operario

Manuel d’utilisation

SAVE THESE INSTRUCTIONS

Manual No. 200267GS

Revision A (06/26/2006)

Model / Modelo/ Modèle

040248

Failure to read and follow the operator’s

manual and all operating instructions can

result in death, bodily injury, and/or

property damage.

WARNING

L’omission de lire et de suivre le manuel de

l’utilisateur et toutes les directives d’utilisation

pourrait entraîner la mort, des blessures

corporelles ou des dommages matériels.

AVERTISSEMENT

Si no se leen y siguen las indicaciones del

Manual del operario y todas las instrucciones

de uso, se pueden producir daños materiales,

lesiones o incluso la muerte.

ADVERTENCIA

Home Generator Systems

Briggs & Stratton Power Products Group, LLC

900 North Parkway

Jefferson, WI 53549

transmitted in any form by any means without the express written

permission of Briggs & Stratton Power Products Group, LLC.

Generator

Model Number 040248

Revision _______

Serial Number __________________

Engine

Model Number _______________________________

Serial Number _______________________________

Date Purchased

Thank you for purchasing this quality-built Briggs & Stratton generator. We are pleased that you’ve placed your

confidence in the Briggs & Stratton brand. When operated and maintained according to the instructions in this manual,

your Briggs & Stratton generator will provide many years of dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with gaseous fueled

generators and how to avoid them. Because Briggs & Stratton does not necessarily know all the applications this

generator could be used for, it is important that you read and understand these instructions. Keep this manual near the

generator for convenient reference.

This generator requires final assembly before use. Refer to the Assembly section of this manual for instructions on final

assembly procedures. Follow the instructions completely.

Where to Find Us

You never have to look far to find Briggs & Stratton support and service for your generator. Consult your Yellow Pages.

There are over 30,000 Briggs & Stratton authorized service dealers worldwide who provide quality service. You can also

contact Briggs & Stratton Customer Service by phone at 1-800-743-4115 or on the Internet at

www.briggsandstratton.com.

1
Table of Contents
Safety Rules.................................................................2
Equipment Description..............................................................................4
The Gaseous Fuel System.........................................................................5
Assembly/Installation .................................................6
Generator Location....................................................................................6
Attach LP Fuel Tank Housing Pad Parts ................................................7
LP Fuel Tank Installation ...........................................................................8
Leak Testing Fuel System..........................................................................9
Battery Connection..................................................................................10
Generator Controls and Features...........................11
Control Panel ............................................................................................12
Receptacles ................................................................................................13
Operating Your Generator......................................14
Starting the Engine....................................................................................14
Connecting Electrical Loads...................................................................14
Stopping the Engine..................................................................................14
Don’t Overload Generator....................................................................16
Maintenance Schedule .............................................17
Oil ................................................................................................................18
Service Air Cleaner Elements................................................................19
Service Spark Plug.....................................................................................20
Check Valve Clearance ...........................................................................20
Engine Air Cooling System.....................................................................20
Charge Battery..........................................................................................20
Storage ........................................................................................................21
Troubleshooting........................................................22
Product Specifications..............................................23
Warranties ................................................................24

2

www.briggsandstratton.com

SAVE THESE INSTRUCTIONS

Safety Rules

This is the safety alert symbol. It is used to

alert you to potential personal injury

hazards. Obey all safety messages that

follow this symbol to avoid possible injury or

death.

The safety alert symbol ( ) is used with a signal word

(DANGER, CAUTION, WARNING), a pictorial

and/or a safety message to alert you to hazards.

DANGER indicates a hazard which, if not avoided, will

result in death or serious injury. WARNING indicates a

hazard which, if not avoided, could result in death or

serious injury. CAUTION indicates a hazard which, if not

avoided, might result in minor or moderate injury.

CAUTION, when used without the alert symbol,

indicates a situation that could result in equipment

damage. Follow safety messages to avoid or reduce the

risk of injury or death.

The manufacturer cannot possibly anticipate every

possible circumstance that might involve a hazard. The

warnings in this manual, and the tags and decals affixed to

the unit are, therefore, not all-inclusive. If you use a

procedure, work method or operating technique that the

manufacturer does not specifically recommend, you must

satisfy yourself that it is safe for you and others. You must

also make sure that the procedure, work method or

operating technique that you choose does not render the

generator unsafe.

Hazard Symbols and Meanings

• Operate generator ONLY outdoors.

• Keep exhaust gas from entering a confined area through windows,

doors, ventilation intakes or other openings.

• DO NOT operate generator inside any building or enclosure

(even if doors or windows are open), including the generator

compartment of a recreational vehicle (RV).

Running generator gives off carbon monoxide,

an odorless, colorless, poison gas.

Breathing carbon monoxide can cause nausea,

fainting or death.

WARNING

The engine exhaust from this product contains

chemicals known to the State of California to

cause cancer, birth defects, or other reproductive

harm.

WARNING

Fire

Read

Manual

Explosive

Pressure

Chemical

Burns

Explosion

Toxic Fumes

Hot Surface

Electrical Shock

• DO NOT dispose of battery in a fire.

• DO NOT allow any open flame, spark, heat, or lit cigarette during

and for several minutes after charging a battery.

• DO NOT open or mutilate the battery.

• Wear protective goggles, rubber apron, and rubber gloves.

• Remove watches, rings, or other metal objects.

• Use tools with insulated handles.

Storage batteries give off explosive hydrogen

gas during recharging.

Slightest spark will ignite hydrogen and cause

explosion.

Battery electrolyte fluid contains acid and is

extremely acidic.

Contact with battery contents will cause severe

chemical burns.

A battery presents a risk of electrical shock and

high short circuit current.

DANGER

Using a generator indoors WILL KILL YOU

IN MINUTES.

Exhaust contains carbon monoxide, a

poison gas you cannot see or smell.

NEVER use in the home

or in partly enclosed

areas such as garages.

ONLY use outdoors and

far from open windows,

doors, and vents.

3

• DO NOT touch hot surfaces and avoid hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5 ft. (152 cm) clearance on all sides of generator

including overhead.

• Code of Federal Regulation (CFR) Title 36 Parks, Forests, and

Public Property require equipment powered by an internal

combustion engine to have a spark arrester, maintained in

effective working order, complying to USDA Forest service

standard 5100-1C or later revision. In the State of California a

spark arrester is required under section 4442 of the California

Public resources code. Other states may have similar laws.

Running engines produce heat. Temperature of

muffler and nearby areas can reach or exceed

150°F (65°C).

Severe burns can occur on contact.

Exhaust heat/gases can ignite combustibles,

structures or damage LP fuel tank causing a fire.

WARNING

• When using generator for backup power, notify utility company.

Use approved transfer equipment to isolate generator from

electric utility.

• DO NOT use when under the influence of drugs or alcohol.

• Despite the safe design of the generator, operating this equipment

imprudently, neglecting its maintenance or being careless can

cause possible injury or death.

• Remain alert at all times while working on this equipment. Never

work on the equipment when you are physically or mentally

fatigued.

• DO NOT touch bare wires or receptacles.

• DO NOT use generator with electrical cords which are worn,

frayed, bare or otherwise damaged.

• DO NOT handle generator or electrical cords while standing in

water, while barefoot, or while hands or feet are wet.

• DO NOT allow unqualified persons or children to operate or

service generator.

• If you must work around a unit while it is operating, stand on an

insulated dry surface to reduce shock hazard.

• In case of an accident caused by electrical shock, immediately shut

down the source of electrical power and contact the local

authorities. Avoid direct contact with the victim.

• Before performing any maintenance on the generator, disconnect

the battery cable indicated by a NEGATIVE, NEG or (-) first.

When finished, reconnect that cable last.

• Remove the 15 Amp fuse BEFORE working on the equipment.

When finished, replace the 15 Amp fuse.

Generator produces hazardous voltage.

Failure to isolate generator from power utility

can result in death or injury to electric utility

workers due to backfeed of electrical energy.

WARNING

• Generator installation must comply with all applicable codes. To

check your local codes, see your local LP gas dealer or natural gas

company.

• Properly secure fuel tanks to LP fuel tank mounting tray as

described in “Assembly”.

• Before using the generator, fuel system hoses must be properly

purged and leak tested, especially after changing fuel tanks.

• No fuel leakage is permitted. NEVER check for leaks using a match

or open flame. Strong odors, colds, sinus congestion, etc. may

prevent the detection of gaseous fuel. Use caution and common

sense when testing for leaks (see “Leak Testing Fuel System”).

• After the generator is positioned for operation, inspect the fuel

system and connecting hoses for evidence of damage, excess wear

or deterioration periodically. If such defects are found, replace

components with manufacturer-supplied replacement parts ONLY.

The fuel hoses and regulator should be replaced every five years.

• When generator is not in use, manually close fuel shut off valve(s).

• DO NOT operate generator if smell of fuel is present.

• DO NOT smoke around generator. Wipe up any oil spills

immediately. Ensure that no combustible materials are left in the

generator compartment. Keep area near the generator clean and

free of debris.

• DO NOT supply unregulated gaseous fuel to generator. See

Product Specifications for required supply pressure.

• DO NOT allow fuel hose(s) to come in contact with hot surfaces.

• DO NOT store LP gas tank(s):

Indoors or in the vicinity of the generator

In a building, garage or any other enclosed area

Within the reach of children.

• LP gas tank must have:

A safety relief device having direct communication with the

cylinder vapor space

A listed over-filling prevention device (OPD)

DOT or CAN/CSA-B339 approval

A shut off valve, terminating in a fuel outlet compatible with

a Type 1 tank connector. No other tank connectors are

permitted for use with this generator.

A collar to protect the fuel shut off valve

• DO NOT insert any foreign objects into the tank valve outlet or

any of the fuel system components.

• LP tank supply system must be arranged for vapor withdrawal.

• Have LP gas tank filled to no more than 80% capacity by a

reputable propane gas dealer and visually inspected and

re-qualified at each filling.

• ALWAYS keep LP gas tanks in an upright position.

• ALWAYS handle LP gas tanks with care.

• The LP fuel tank is equipped with an internal thermal device that

will permanently shut off gas flow if the tank is subjected to

temperatures above 240° F (115° C). If this should happen, take

the LP fuel tank to your fuel supplier. The cause of the excessive

heat should be determined and corrected before using your

generator again.

• The normal flow of gas through the regulator and hose assembly

can create a humming noise. A low volume of noise is normal and

will not interfere with generator operation. If humming noise is

loud and excessive, the fuel supply system must be purged.

Propane and Natural Gas are extremely

flammable and explosive.

Fire or explosion can cause severe burns or

death.

WARNING

• This generator does not meet U. S. Coast Guard Regulation

33CFR-183 and should not be used on marine applications.

• Failure to use the appropriate U. S. Coast Guard approved

generator could result in death or serious injury and/or property

damage.

WARNING

4

www.briggsandstratton.com

Equipment Description

Read this manual carefully and become

familiar with your generator. Know its

applications, its limitations and any hazards

involved.

The generator is an engine–driven, revolving field,

alternating current (AC) generator. It was designed to

supply electrical power for operating compatible electrical

lighting, appliances, tools and motor loads. The generator’s

revolving field is driven at about 3,600 rpm by a single-

cylinder engine. The generator is operated on liquefied

propane (LP) gas. It can operate on natural gas (NG) fuel

only after conversion by a licensed professional gaseous

fuel technician.

This generator incorporates GFCI (Ground Fault Circuit

Interrupter) outlet protection and has its neutral bonded

to grounding fastener to comply to OSHA inspections on

job sites.

This generator will not function when connected to a

2 pole transfer switch since its service disconnect also has

a neutral bonded to ground. When both the generator

and the home or building’s service disconnect contains a

neutral bonded to ground, the generator’s GFCI will open

and no outlets will function.

A switching neutral transfer switch MUST be used if the

generator is connected to a building’s electrical system.

This product is intended for residential use as an all-

weather temporary source of electric power. It is capable

of supplying power to loads such as heating, refrigeration

systems, and communication systems. This product does

not qualify for emergency standby as defined by NFPA 70

(NEC). DO NOT use this generator for anything other

than it’s intended purpose.

Every effort has been made to ensure that the information

in this manual is both accurate and current. However, the

manufacturer reserves the right to change, alter or

otherwise improve the generator and this documentation

at any time without prior notice.

• DO NOT remove the neutral bond.

• Removing the neutral bond could result in death, bodily injury

and/or property damage.

GFCI will not function if neutral bond removed

DANGER

• See “Don’t Overload Generator”.

• Start generator and let engine stabilize before connecting electrical

loads.

• Connect electrical loads in OFF position, then turn ON for

operation.

• Turn electrical loads OFF and disconnect from generator before

stopping generator.

Exceeding generators wattage/amperage capacity can

damage generator and/or electrical devices connected

to it.

CAUTION

• Use generator only for intended uses.

• If you have questions about intended use, ask dealer or contact

Briggs and Stratton.

• Operate generator only on level surfaces.

• Adequate, unobstructed flow of cooling and ventilating air is

critical to correct generator operation.

• The access door and roof must be installed whenever the unit is

running.

• DO NOT expose generator to excessive moisture, dust, dirt, or

corrosive vapors.

• DO NOT start engine with air cleaner or air cleaner cover

removed.

• DO NOT insert any objects through cooling slots.

• DO NOT use the generator or any of its parts as a step. Stepping

on the unit can cause stress and break parts. This may result in

dangerous operating conditions from leaking exhaust gases, fuel

leakage, oil leakage, etc..

• If connected devices overheat, turn them off and disconnect them

from generator.

• Shut off generator if:

-electrical output is lost;

-equipment sparks, smokes, or emits flames;

-unit vibrates excessively.

Improper treatment of generator can damage it and

shorten its life.

CAUTION

• FOR RESIDENTIAL USE ONLY. DO NOT use this generator for

anything other than its intended purpose.

• DO NOT tamper with governed speed. Generator supplies

correct rated frequency and voltage when running at governed

speed.

• DO NOT modify generator in any way.

Excessively high operating speeds increase risk of injury

and damage to generator.

Excessively low speeds impose a heavy load.

CAUTION

When adjusting or making repairs to your

generator:

• Disconnect the spark plug wire from the spark plug and place the

wire where it cannot contact spark plug.

When testing for engine spark:

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.

Unintentional sparking can result in fire or

electric shock.

WARNING

5

Ground Fault Protection

The generator’s receptacles are equipped with Ground

Fault Circuit Interrupter (GFCI) protection. This GFCI

device meets applicable federal, state and local codes.

The GFCI protects against electrical shock that may be

caused if your body becomes a path in which electricity

travels to reach the ground. This could happen if you

touch a “Live” appliance or wire, or are touching plumbing

or other materials that connect to the ground.

When protected by a GFCI device, one may still feel a

shock, but the GFCI should cut current off quickly enough

so that a person in normal health should not suffer any

serious electrical injury.

Connections

to a Building’s Electrical

System

Connections from this generator to a building’s electrical

system must be made through a switching neutral transfer

switch installed by a qualified electrician. The connection

must isolate the generator power from utility power, and

must comply with all applicable laws and electrical codes.

IMPORTANT: A switching neutral transfer switch MUST

be used when switching between utility and generator power.

Customer’s Responsibilities

• If considering installation with a transfer swith, read

and follow the instructions given in this manual.

• Follow a regular schedule in maintaining, caring for

and using your generator, as specified in this manual.

• ALWAYS disconnect and store indoors the cord used

to connect generator and inlet connection box when

generator is not in use.

To help you make informed choices and communicate

effectively with your installation contractor(s),

Read and understand the Assembly section of

this manual before starting your generator

installation.

You can arrange for proper installation by contacting the

store at which you purchased your generator, your Briggs

& Stratton dealer, a licensed professional electrician or

your utility power provider.

The generator warranty is VOID if permanent fuel

connections to the generator are installed by

anyone other than a licensed gaseous fuel

professional.

The generator warranty is VOID if permanent

electrical connections to the generator are made.

The Gaseous Fuel System

The generator unit has been factory set to run on

liquefied petroleum gas. If the generator is to run on

natural gas, the engine will need to be reconfigured using

the supplied NG Conversion kit. Contact a licensed

professional gaseous fuel technician to install this kit.

The generator engine is fitted with a fuel mixer system

that meets the specifications of the California Air

Resources Board for “tamper-proof” dual fuel systems.

The unit will run on natural gas or liquefied propane

vapor.

• Use clean, dry fuel, free of moisture or any particulate

material. Using fuels outside the following

recommended values may cause performance

problems:

• Commercial grade HD5 LPG is recommended -

minimum fuel energy of 2500 BTU’s/ft

3

with maximum

propylene content of 5% and butane and heavier gas

content of 2.5% and minimum propane content of 90%.

• See “Specifications” for required fuel supply pressure.

Fuel Consumption

See the following table for fuel supply requirements at half

and full load for both natural gas and LP vapor.

• Contact with the hot and neutral conductor at the same time can

cause electrical shock or burn, even if the circuit is GFCI

protected.

• Before using the GFCI receptacle, ALWAYS push the test button

to insure it works.

Generator produces hazardous voltage/current.

WARNING

Only qualified electricians and gaseous fuel

technicians should attempt fuel conversion or

permanent connection of this generator. Each

installation must strictly comply with applicable

codes, standards and regulations.

WARNING

• LP gas is heavier than air and will settle in low areas.

• Natural gas is lighter than air and will collect in high areas.

• The slightest spark can ignite these fuels and cause an explosion.

• IF YOU SMELL GAS - Shut off gas to the generator at the LP

cylinder(s)/source.

• If odor continues, leave the area and immediately call your gas

supplier or fire department.

Propane and Natural Gas are extremely

flammable and explosive.

Fire or explosion can cause severe burns or

death.

WARNING

Natural Gas* LP Vapor**

1/2 Load Full Load 1/2 Load Full Load

80 137 33 56

* = Natural Gas is in cubic feet per hour

** = LP Vapor is in cubic feet per hour

Fuel Supply Requirements

Generator Location

Consider these factors when determining the proper

generator operating location:

• Install the unit outdoors on a flat, level surface with

provisions for adequate ventilation. This will allow for

dispersion of deadly exhaust gas. DO NOT install

generator where exhaust gas could accumulate and

enter inside or be drawn into a potentially occupied

building areas.

Ensure exhaust gas is kept away from any windows,

doors, ventilation intakes or other openings that can

allow exhaust gas to collect in a confined area

(Figure 1). Prevailing winds and air currents should be

taken into consideration when positioning generator.

• The unit must have at least 5 ft. (152 cm) of clearance

on all sides of the enclosure and LP tank housing pad,

including overhead. This will reduce the risk of

exhaust heat or exhaust gases igniting nearby

combustible materials and will provide for adequate

cooling and generator maintenance.

6

www.briggsandstratton.com

Assembly/Installation

Your generator is ready for use after you assemble the LP

fuel tank housing pad components, make proper fuel

connections, and verify that engine oil is at the proper

level.

If you have any problems with the assembly of your

generator, please call the generator helpline at

1-800-743-4115. If calling for assistance, please have the

model, revision, and serial number from the data tag

available. See “Generator Controls and Features” for data

tag location.

Shipment Contents

The generator is supplied with:

• Generator pre-attached to mounting pad

• LP fuel tank housing tray assembly pre-attached to

mounting pad

• Fuel hose and regulator assembly pre-attached to

generator

• LP fuel tank all-weather cover

• Bag containing LP fuel tank attachment hardware

• Operator’s manual

• Battery

• Oil drain tray

• Touch-up paint

• One spare 15A fuse

• NG conversion kit

You must purchase two filled 20 pound DOT LP fuel tanks

that are equipped with a listed over-filling prevention

device (OPD).

Lifting the Generator

CAUTION The generator weighs more than

280 pounds (130 kg). Proper tools, equipment and

qualified personnel should be used in all phases of

handling and moving the generator. Each full LP

tank will weigh more than 20 pounds (9 kg).

CAUTION DO NOT lift unit by roof as damage to

generator will occur.

Lifting pockets are provided at each corner between the

base of the generator and its mounting pad. See

“Generator Controls and Features” for locations. Retouch

any chipped paint with supplied touch-up paint.

• Keep at least 5 ft. (152 cm) clearance on all sides of generator

including overhead.

Exhaust heat/gases can ignite combustibles,

structures or damage LP fuel tank causing a fire.

WARNING

CAUTION

• Refer to Maintenance for oil fill information.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

Any attempt to crank or start the engine without

verifying it has been properly serviced with the

recommended oil will result in equipment failure.

Figure 1 — Generator Clearances

A - Engine Exhaust Opening

A

Using a generator indoors WILL KILL YOU

IN MINUTES.

Exhaust contains carbon monoxide, a

poison gas you cannot see or smell.

NEVER use in the home

or in partly enclosed

areas such as garages.

ONLY use outdoors and

far from open windows,

doors, and vents.

7

• Install the unit in a location where sump pump

discharge, rain gutter down spouts, roof run-off,

landscape irrigation, or water sprinklers will not flood

the unit or spray the enclosure and enter any air inlet

or outlet openings.

• Install the unit where the location of any services such

as phone, electrical, fuel, air conditioning, irrigation,

including covered, concealed and underground

services will not be affected or obstructed.

• Install the unit where air inlet and outlet openings will

not become obstructed by leaves, grass, snow, etc. If

prevailing winds will cause blowing or drifting, you

may need to construct a windbreak to protect the

unit.

The generator is shipped already attached to its mounting

pad. Unless mandated by local code, a concrete slab is not

required.

If mandated by local code, construct a concrete slab at

least 3 inches thick and 6 inches longer and wider than the

combined generator and LP tank pad footprint. Attach

pads to slab with 1/4” diameter (minimum) masonry

anchor bolts.

Attach LP Fuel Tank Housing Pad Parts

Required Tools

You will need either of the following tools to attach the

LP fuel tank housing pad to the generator pad:

• 1/2 inch (13 mm) socket and ratchet OR

• 1/2 inch (13 mm) open end wrench

Attach Mounting Pads Together

1. Place LP tank housing pad (with pre-attached LP fuel

tank tray) on the ground next to the side of the

generator where the fuel hose(s) and regulator are

attached.

Confirm that the pre-drilled holes on both mounting

pads are adjacent to each other (see Figure 2).

2. Lay one 20 inch (50 cm) angle bracket across both

mounting pads, aligning the bracket holes with the

pre-drilled pad holes, as shown in Figure 2.

3, Pass one 5/16” X 1” lag bolt through one 5/16” flat

washer, then through one hole on the angle bracket.

Finger tighten lag bolt into mounting pad hole (see

Figure 3).

4. Repeat Step 3 three more times, placing a lag

bolt/washer in each angle bracket hole.

5. Tighten each lag bolt until snug using specified tool.

DO NOT over-tighten as threads could strip.

6. Repeat Steps 2 through 5 to attach the second angle

bracket to the opposite ends of the mounting pads.

Attach Tank Hold-Down Rod

Insert either end of the supplied threaded rod into the LP

fuel tank tray location shown in Figure 4. Hand tighten

rod.

Figure 2 — Mounting Pad and Angle Bracket Holes

A - Mounting Pad Holes

B - Angle Bracket

B

A

Figure 3 — Start Lag Bolts into Mounting Pad Holes

A - Mounting Pad

B - Flat Washer

C - Lag Bolt

D - Angle Bracket

C

DBA

Figure 4 — Attach Tank Hold-Down Rod to LP Tank Tray

A - Hold-Down Rod

B - LP Fuel Tank Tray

A

B

8

www.briggsandstratton.com

LP Fuel Tank Installation

IMPORTANT: To ensure optimal performance,

use two (2) LP fuel tanks during operation.

This section describes the proper method of installing and

leak testing the generator’s LP fuel tanks. This system is

supplied with an LP fuel tank cover. Always cover the LP

fuel tanks whenever they are connected to the generator.

To Install LP Fuel Tanks:

1. Confirm both LP fuel tank shut off valves are closed

(turned fully CLOCKWISE).

2. Place each LP tank into the LP tank tray with it’s fuel

valve pointing towards the generator (see Figure 5).

3. Slide the LP fuel tank hold-down bracket onto the

threaded rod. Position the bracket so that its notches

are aligned with both LP fuel tank collar holes, as

shown in Figure 6.

It may be necessary to “wiggle” the LP fuel tanks and

the bracket to obtain proper alignment.

4. Slide the fuel hose/regulator assembly over the

threaded rod so that it faces the generator and rests

on the hold-down bracket (see Figure 7).

5. Thread the wing nut CLOCKWISE onto the threaded

rod. Hand tighten wing nut against fuel hose/regulator

assembly, ensuring hold-down bracket notches remain

engaged with LP fuel tank collars and LP fuel tanks are

held firmly. See Figure 8.

6. Remove protective covers from both LP fuel tank shut

off valve connectors. DO NOT discard protective

covers - they should be installed any time the LP fuel

tank is disconnected from the generator.

7. Insert the nipple of the left connection device (as you

face the generator and LP fuel tanks) into the left LP

fuel tank valve outlet (see Figure 9). Ensure it is fully

inserted.

• The slightest spark can ignite this fuel and cause an explosion.

• IF YOU SMELL GAS - Shut off gas to the generator at the LP fuel

tank(s).

• If odor continues, leave the area and immediately call your gas

supplier or fire department.

Propane Gas is extremely flammable and

explosive.

Fire or explosion can cause severe burns or

death.

WARNING

Figure 5 — Proper Position for LP Fuel Tanks

A - LP Fuel Tank Shut Off Valve Connector

B - LP Fuel Tank

B

A

Figure 6 — Properly-Aligned Hold-Down Bracket

A - Bracket Notch over Fuel Tank Collar

B - Hold-Down Bracket

BA

Figure 7 — Fuel Hose/Regulator Assembly Placement

A - Hold-Down Bracket

B - Threaded Rod

C - Fuel Hose/Regulator Assembly

A B C

Figure 8 — Properly-Secured LP Fuel Tanks

A - LP Fuel Tank

B - Wing Nut

C - Fuel Hose/Regulator Assembly

A

B

C

3. Using a sponge, rag or small non-metallic brush, apply

the soap water mixture at each of the locations

shown in Figure 10 below.

4. Check each location shown in Figure 10 for growing

bubbles, which indicates a fuel leak. Bubbles will look

something like this:

5. Close both LP fuel tank shut off valves (turn fully

CLOCKWISE).

6. Press and hold control panel’s START/RUN/STOP

switch in START position for 5 seconds to release gas

pressure in hoses. See “Control Panel Controls and

Features”.

7. Tighten or replace any leaking connections.

9

8. Turn the large coupling nut CLOCKWISE and hand

tighten to a full stop.

DO NOT cross thread the connection.

DO NOT use thread sealant.

DO NOT over-tighten the coupling nut.

DO NOT use tools to tighten the connection.

NOTE: If you are unable to make the connection, repeat

Step 7 or contact an LP fuel professional.

9. Repeat Steps 7 and 8 to attach the right LP fuel tank.

10. Confirm that each fuel hose does not have kinks and

that it does not touch sharp edges or surfaces that

may become hot during generator operation.

11. Perform a complete fuel leak test, using the

instructions given in “Leak Testing Fuel System”.

Leak Testing Fuel System

1. Create a mixture of 50% water and 50% liquid

dishwashing soap.

2. Turn ON the fuel supply by turning both LP fuel tank

shut off valves one full turn COUNTERCLOCKWISE.

Figure 10 — Leak Test Locations

A - LP Fuel Tank Welds

B - LP Fuel Tank Shut Off Valves at Cylinder

Connections

C - Both Coupling Nuts to LP Fuel Tank Shut Off Valve

Connections

D - Back Sides of Coupling Nuts and Hose Connection

Joints

E - Brass T-Valve Connections (all joints)

F - Regulator Connection to Fuel Hose

G - The Full Length of all Fuel Hoses

H - Fuel Hose Connection to Generator (all joints)

A

D

B G H

G

E

F

E

C D

G

B G

• DO NOT smoke or permit ignition sources in the area while

conducting a leak test.

• Perform leak test OUTDOORS only in a well ventilated area.

• DO NOT perform a leak test with a match or open flame.

• DO NOT perform a leak test while the generator is in use.

• ALWAYS perform a leak test when first using the generator.

• ALWAYS perform a leak test every time an LP fuel tank or any

fuel system component is changed.

• ALWAYS perform a leak test whenever the generator is moved.

• Perform a leak test at least once per year or if your generator has

not been used for more than 60 days.

Propane Gas is extremely flammable and

explosive.

Fire or explosion can cause severe burns or

death.

WARNING

Figure 9 — Proper Connection Device Alignment

A - Fuel Hose Connector Nipple

B - LP Fuel Tank Shut Off Valve Connector

B

A

10

www.briggsandstratton.com

8. Repeat Steps 2 through 7 until no leaks are detected.

DO NOT use the generator if leaks cannot be

stopped. Contact a qualified LP fuel professional for

assistance.

9, Turn OFF both LP fuel tank shut off valves until you

are ready to use the generator.

10. Wash off soapy residue with clean cold water and

towel dry.

11. Wait five minutes to allow all gas to evacuate the area

before starting the generator.

NOTE: The leak test must be performed in an area that

has adequate lighting in order to see if bubbles are

developing. DO NOT use a flashlight to check for bubbles.

To Remove LP Fuel Tank(s)

1. Confirm the LP fuel tank shut off valve is closed

(turned fully CLOCKWISE).

2. Disconnect the fuel hose from the LP tank by turning

the large coupling nut COUNTERCLOCKWISE by

hand (see Figure 9).

3. Install the protective cover over the LP fuel tank shut

off valve outlet.

4. Remove wing nut from threaded rod by turning it

COUNTERCLOCKWISE. Lift and remove the fuel

hose/regulator assembly from the threaded rod. See

Figures 7 and 8.

5. Lift and remove the LP tank hold-down bracket from

threaded rod (see Figure 6). It may be necessary to

wiggle the LP fuel tanks to release the hold-down

bracket.

6. Carefully lift the LP fuel tank off the LP fuel tank tray.

Verify Engine Oil Level

The generator engine is shipped from the factory filled

with synthetic oil (API SJ/CF 5W-30W). This allows for

generator operation in the widest range of temperature

and climate conditions. Before starting the engine, check

oil level and ensure that engine is serviced as described in

“Maintenance”.

NOTE: The use of synthetic oil does not alter the

required oil change intervals described in the

Maintenance section.

Removable Roof and Access Door

The generator enclosure includes a removable roof and

battery access door.

To Remove Roof:

There are two screws on each side of the roof located in

the half-moon roof slots. Remove the four screws and lift

roof off.

To Remove Battery Access Door:

1. Disconnect any loads connected to the generator.

2. Remove roof as described above.

3. Remove screw at top of access door.

4. Pull access door outward (away) from unit while

pulling door upward and out of base.

Door will come free of generator enclosure.

To Install Battery Access Door and Roof:

1. Guide bottom of access door into base.

2. Push access door in until it is flush with sides.

3. Replace door screw.

4. Replace roof and four roof screws.

Battery Connection

The generator is supplied with a sealed, lead-acid

rechargeable 12 Volt DC, AGM type, 33 Amp-Hour,

battery. The battery cables are connected at the factory.

The battery will lose some charge in shipping and prior to

generator installation. If battery voltage is too low to start

the engine, charge the battery, as described in

“Maintenance”.

If the battery fails to take a charge, it must be replaced

ONLY with the same type of 12 Volt DC, AGM type,

33 Amp-Hour battery. DO NOT replace with liquid

electrolyte lead-acid type battery.

CAUTION

• Refer to Maintenance for oil fill information.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

Any attempt to crank or start the engine without

verifying it has been properly serviced with the

recommended oil will result in equipment failure.

• DO NOT dispose of battery in a fire.

• DO NOT allow any open flame, spark, heat, or lit cigarette during

and for several minutes after charging a battery.

• DO NOT open or mutilate the battery.

• Wear protective goggles, rubber apron, and rubber gloves.

• Remove watches, rings, or other metal objects.

• Use tools with insulated handles.

Storage batteries give off explosive hydrogen

gas during recharging.

Slightest spark will ignite hydrogen and cause

explosion.

Battery electrolyte fluid contains acid and is

extremely acidic.

Contact with battery contents will cause severe

chemical burns.

A battery presents a risk of electrical shock and

high short circuit current.

DANGER

11

Generator Controls and Features

Read this Operator’s Manual and safety rules before operating your generator.

Compare the illustrations with your generator, to familiarize yourself with the locations of various controls and

adjustments. Save this manual for future reference.

Generator is shown with roof, oil filter access door, battery access door and control panel cover removed.

See Figures 5 through 8, earlier, for important LP fuel tank component views.

N

A

M

G

L

KH

CB

E

D

F

A - Engine Model Number Identification — (stamped

on top of valve cover) Identifies engine model and type.

B - Rotating Screen — Prevents large debris from

entering engine cooling airflow stream.

C - Oil Fill Cap/Dipstick — Check and fill engine with

recommended oil here.

D - Control Panel — Used for various operation and

maintenance functions. See “Control Panel Controls and

Features” on next page.

E - Oil Drain Hose — Provided to facilitate oil changing.

F - Unit Data Decal — Displays model, revision and

serial numbers.

G - Battery — 12 Volt DC, 33 Amp-Hour, sealed battery

provides power to start engine. Battery receives trickle

charge whenever generator is running.

H - Equipment Grounding Terminal — Connect

generator to earth ground here.

K - Lifting Pockets — Provided at each lower corner

for lifting generator and attached pad.

L - Fuel Inlet — Fuel supply components are attached to

generator here.

M - Exhaust Port — High-performance muffler lowers

engine noise to comply with most residential codes.

Includes approved spark arrester.

N - Oil Filter — Filters engine oil to prolong generator

life.

P - Hazard/Start/Stop Instructions — Observe these

warnings and procedures when operating generator.

R - Air Cleaner — Uses a dry type filter element and

foam precleaner to

protect engine by filtering dust and

debris out of intake air.

R

P

12

www.briggsandstratton.com

GFCI

MAIN BREAKER

PUSH

TO

RESET

Control Panel Controls and Features

Compare this illustration with your generator’s Control Panel, to familiarize yourself with the locations of the receptacles,

controls and circuit breakers:

A - LED Light — Generator is producing voltage when

illuminated.

B - Ground Fault Circuit Interrupter/Breaker —

Protects the generator from over-current conditions

electrical faults to ground and must be in the “ON”

position to supply power to all of the control panel

receptacles.

C - START/RUN/STOP Switch — This three-position

switch is used as follows:

•“START” position starts the generator. Press and

hold to start generator.

•“RUN” position is switch position while generator is

running.

•“STOP” position turns off the generator. Press and

hold until engine stops.

D - 120/240V 30 Amp Locking Receptacle —

Supplies the total generator output power and is

GFCI protected.

E - Push-to-Reset Circuit Breakers — Protects the

generator from current overload at receptacle.

F - 120 Volt 20 Amp Receptacles — Each receptacle

can supply a maximum of 20 amperes of power. The

120 Volt receptacles are GFCI protected. Total load

on all four receptacles cannot exceed 7000 watts.

G - 15 Amp Fuse — Protects the generator DC control

circuits. If the fuse has melted open or was removed,

the engine cannot crank or start. Replace the fuse

using only an identical ATO-type 15A fuse, available

from most automotive parts stores.

120/240V 30A

G

C

A

E

F

D

B

PUSH

TO

RESET

120V 20A

ALL RECEPTACLES GFCI-PROTECTED

120V 20A

15A FUSE

START/RUN/STOP

13

Receptacles

120/240 Volt AC, 30 Amp, Locking

Receptacle

This receptacle (Figure 11) supplies the entire generator

output and is protected against overload by a double-pole

GFCI circuit breaker.

Use a NEMA L14–30 plug with this receptacle. Connect a

4–wire cord set rated for 250 Volt AC loads at 30 Amps

(or greater). You can use the same 4–wire cord if you

plan to run a 120 Volt load. Inspect cord set(s) before

each use. Store cord set(s) indoors.

When operating on LP fuel, this receptacle powers

120/240 Volt AC, 60 Hz, single phase loads requiring up

to 7,000 watts of power (7.0 kW) at 29.16 Amps for

240 Volts or two independent 120 Volt loads at

29.16 Amps each.

120 Volt AC, 20 Amp, Duplex Receptacles

Each individual duplex receptacle (Figure 12) is protected

against overload by a push-to-reset circuit breaker. All

four receptacles are also protected by a double-pole GFCI

circuit breaker.

Use each receptacle to operate 120 Volt AC,

single–phase, 60 Hz electrical loads requiring up to

2,400 watts (2.4 kW) at 20 Amps of current when

operating on LP fuel. Use cord sets that are rated for

125 Volt AC loads at 20 Amps (or greater). Inspect cord

set(s) before each use.

NOTE: Follow all safety precautions when connecting any

extension cord or device to the generator.

Equipment Ground

The generator is equipped with an equipment grounding

terminal that connects the generator frame components

to the ground terminals on the AC output receptacles.

Ground the generator per applicable codes, standards, and

regulations.

The equipment ground is connected to the AC neutral

wire and the neutral is bonded to the generator frame.

The equipment grounding terminal is shown on

“Generator Controls and Features”.

Special Requirements

There may be Federal or State Occupational Safety and

Health Administration (OSHA) regulations, local codes, or

ordinances that apply to the intended use of the

generator. Please consult a qualified electrician, electrical

inspector, or the local agency having jurisdiction.

• In some areas, generators are required to be

registered with local utility companies.

• If the generator is used at a construction site, there

may be additional regulations which must be

observed.

• NEVER attempt to power a device requiring more amperage than

generator or receptacle can supply.

• DO NOT overload the generator. See “Don’t Overload

Generator”.

Receptacles may be marked with rating value greater

than generator output capacity.

CAUTION

• See “Don’t Overload Generator”.

• Start generator and let engine stabilize before connecting electrical

loads.

• Connect electrical loads in OFF position, then turn ON for

operation.

• Turn electrical loads OFF and disconnect from generator before

stopping generator.

Exceeding generators wattage/amperage capacity can

damage generator and/or electrical devices connected

to it.

CAUTION

Figure 11 — 120/240 Volt AC, 30 Amp Receptacle

4-Wire Cord Set

240V

120V

W (Neutral)

X (Hot)

Y (Hot)

NEMA L14-30

Ground (Green)

Figure 12 — 120 Volt, 20 Amp Duplex Receptacle

14

www.briggsandstratton.com

Operating Your Generator

Starting the Engine

Use the following start instructions:

1. Make sure unit is on a flat, level surface.

IMPORTANT: Failure to start and operate unit on a

level surface will cause the unit not to start or shut down

during operation.

2. Open control panel cover using standard screwdriver.

3. Disconnect all load(s) to generator.

4. Open LP tank fuel shut off valve(s).

5. Confirm 15 Amp fuse is installed in control panel.

6. Push and hold START/RUN/STOP switch in START

position until engine starts and control panel LED is

ON.

IMPORTANT: If you release the switch from the

START position before red LED comes on, the generator

will shut down.

NOTE: DO NOT crank engine for more than

15 seconds, then pause for 15 seconds to reduce heat in

starter. Repeat start process until engine starts.

NOTE: When starting generator, air may be present in

the fuel line(s), especially after changing fuel tanks. It may

take several starting cycles to purge that air before the

engine will start.

Connecting Electrical Loads

1. Let engine run for two minutes after starting.

2. Open control panel cover and confirm generator’s

main circuit breaker is in the ON (closed) position.

See “Control Panel Controls and Features”.

3. Plug in, then turn on the desired 120 and/or 240 Volt

AC, single phase, 60 Hz electrical loads.

3. Close and latch control panel cover.

IMPORTANT:

• DO NOT connect 240 Volt loads to the 120 Volt

duplex receptacles.

• DO NOT connect 3–phase loads to the generator.

• DO NOT connect 50 Hz loads to the generator.

• DO NOT OVERLOAD THE GENERATOR. See

“Don’t Overload Generator”.

Stopping the Engine

1. Open control panel cover using standard screwdriver.

2. Turn OFF all electrical loads. Disconnect them from

control panel receptacles.

Never start or stop engine with electrical devices

plugged in and turned on.

3. Let engine run for two minutes with no loads to

stabilize internal temperatures of engine and

generator.

4. Push and hold START/RUN/STOP switch in STOP

position until LED turns off and engine stops.

5. Close manual fuel shut off valve(s).

6. Close and latch control panel cover.

These steps should be performed after the generator has been

assembled, stored, moved, cleaned, or repaired. DO NOT operate this

generator until you have read and understand ALL of the warnings and

instructions in this operator’s manual.

• Insure that the generator is properly assembled.

• Inspect the LP fuel supply hoses for burns, chaffing, kinks, and

proper routing before each use. Hoses should be kept at least

3 inches (8 cm) away from hot surfaces.

• Leak test all LP fuel connections and and hoses. See “Leak Testing

Fuel System”.

• Position your generator on level ground in a well ventilated

location, 5 feet (152 cm) away from combustible materials and

buildings, including overhead. DO NOT use generator on wooden

decks or other surfaces that could burn.

Propane Gas is extremely flammable and

explosive.

Fire or explosion can cause severe burns or

death.

WARNING

• DO NOT touch hot surfaces and avoid hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5 ft. (152 cm) clearance on all sides of generator

including overhead.

Running engines produce heat. Temperature of

muffler and nearby areas can reach or exceed

150°F (65°C).

Severe burns can occur on contact.

Exhaust heat/gases can ignite combustibles,

structures or damage LP fuel tank causing a fire.

WARNING

15

Ground Fault Protection

This unit is equipped with a Ground Fault Circuit

Interrupter (GFCI). This device meets applicable federal,

state and local codes.

Test GFCI Circuit Breaker

Test your GFCI circuit breaker (see “Control Panel

Controls and Features” for location) every month, as

follows:

1. While generator is running and control panel cover

open, push white “Test” button. The circuit breaker

should trip (handle will move to approximate center

position), which will disconnect power to outlets.

2. If handle moves to center, reset circuit breaker by

firmly moving handle to “Off” (left) position, then to

“On” (right) position.

During Generator Use

If circuit breaker trips during use, it usually indicates faulty

electrical equipment or cords. However, test the circuit

breaker as follows;

1. Open control panel cover, disconnect loads, reset and

test circuit breaker as described earlier. Let generator

run without any loads for 1 minute.

2. If circuit breaker tests correctly, the electrical

equipment or extension cords may be faulty. Replace

faulty electrical equipment and cords before further

use.

• DO NOT use generator.

• Call a Briggs & Stratton Power Products service center.

If circuit breaker does not trip:

CAUTION

• DO NOT use generator.

• Call a Briggs & Stratton Power Products service center.

If circuit breaker does not reset properly:

CAUTION

• DO NOT use generator.

• Call a Briggs & Stratton Power Products service center.

If circuit breaker trips in the 1 minute period:

CAUTION

• Have qualified personnel check all electrical equipment and cords

for any defects.

• Replace electrical equipment and cords or take to a qualified

repair center.

If circuit breaker tests correctly:

CAUTION

16

www.briggsandstratton.com

Don’t Overload Generator

Capacity

You must make sure your generator can supply enough

rated (running) and surge (starting) watts for the items

you will power at the same time. Follow these simple

steps:

1. Select the items you will power at the same time.

2. Total the rated (running) watts of these items. This is

the amount of power your generator must produce

to keep your items running. See Figure 13.

3. Estimate how many surge (starting) watts you will

need. Surge wattage is the short burst of power

needed to start electric motor-driven tools or

appliances such as a circular saw or refrigerator.

Because not all motors start at the same time, total

surge watts can be estimated by adding only the

item(s) with the highest additional surge watts to the

total rated watts from step 2.

Example:

Total Rated (Running) Watts = 3075

Highest Additional Surge Watts = 1800

Total Generator Output Required = 4875

Power Management

To prolong the life of your generator and attached

devices, it is important to take care when adding electrical

loads to your generator. There should be nothing

connected to the generator outlets before starting it's

engine. The correct and safe way to manage generator

power is to sequentially add loads as follows:

1. With nothing connected to the generator, start the

engine as described in this manual.

2. Plug in and turn on the first load, preferably the

largest load you have.

3. Permit the generator output to stabilize (engine runs

smoothly and attached device operates properly).

4. Plug in and turn on the next load.

5. Again, permit the generator to stabilize.

6. Repeat steps 4 and 5 for each additional load.

Never add more loads than the generator capacity.

Take special care to consider surge loads in

generator capacity, as described above.

*Wattages listed are approximate only. Check tool or

appliance for actual wattage.

Figure 13 — Wattage Reference Guide

Tool or Appliance

Rated*

(Running)

Watts

Additional

Surge

(Starting)

Watts

Essentials

Light Bulb - 75 watt

75

-

Deep Freezer

500

Sump Pump

800

1200

Refrigerator/Freezer - 18 Cu. Ft.

800

1600

Water Well Pump - 1/3 HP

1000

2000

Heating/Cooling

Window AC - 10,000 BTU

1200

1800

Window Fan

300

600

Furnace Fan Blower - 1/2 HP

800

1300

Kitchen

Microwave Oven - 1000 Watt

1000

-

Coffee Maker

1500

-

Electric Stove - Single Element

1500

-

Hot Plate

2500

-

Family Room

DVD/CD Player

100

-

VCR

100

-

Stereo Receiver

450

-

Color Television - 27”

500

-

Personal Computer w/17” monitor

800

-

Other

Security System

180

-

AM/FM Clock Radio

300

-

Garage Door Opener - 1/2 HP

480

520

Electric Water Heater - 40 Gallon

4000

-

DIY/Job Site

Quartz Halogen Work Light

1000

-

Airless Sprayer - 1/3 HP

600

1200

Reciprocating Saw

960

Electric Drill - 1/2 HP

1000

Circular Saw - 7 1/4”

1500

Miter Saw - 10”

1800

Table Planer - 6”

1800

Table Saw/Radial Arm Saw - 10”

2000

Air Compressor - 1-1/2 HP

2500

17

Maintenance Schedule

Follow the hourly or calendar intervals, whichever occurs first.

More frequent service is required when operating in adverse conditions noted below.

General Recommendations

Regular maintenance will improve the performance and

extend the life of the generator. See any authorized Briggs

& Stratton dealer for service. Never operate a

damaged or defective generator. To receive full value

from the warranty, the operator must maintain the

generator as instructed in this section.

All service and adjustments should be made at least once

each season. Follow the requirements in the “Maintenance

Schedule” chart above.

NOTE: Once a year you should clean or replace the

spark plug and replace the air filter. A new spark plug and

clean air filter assure proper fuel-air mixture and help

your engine run better and last longer.

NOTE: The alternator assembly rotates on a

prelubricated and sealed ball bearing that requires no

additional lubrication for the life of the bearing.

Emissions Control

Maintenance, replacement or repair of the emissions

control devices and systems may be performed by any

non-road engine repair establishment or individual. See

“Emissions Control System Warranty”.

Maintenance

Maintenance consists of keeping the unit clean. Operate

the unit in an environment where it will not be exposed

to excessive dust, dirt, moisture or any corrosive vapors.

Cooling air louvers on the enclosure must not become

clogged with snow, leaves, or any other foreign material.

Inspect cooling air slots and openings on generator. These

openings must be kept clean and unobstructed.

Check the cleanliness of the unit frequently and clean

when dust, dirt, oil, moisture or other foreign substances

are visible on its exterior/interior surface.

NOTE: DO NOT use direct spray from a garden hose to

clean generator. Water can enter the engine and

generator and cause problems.

Clean Debris

• Use a damp cloth to wipe exterior surfaces clean.

• Use a soft bristle brush to loosen caked on dirt or oil.

• Use a vacuum cleaner to pick up loose dirt and

debris.

1 Change oil sooner when operating under dirty or dusty conditions.

2 Replace more often under dirty or dusty conditions.

3 Check yearly only.

4 Clean more often under dirty or dusty conditions.

5 Replace every five years.

MAINTENANCE SCHEDULE

FILL IN DATES AS YOU

COMPLETE REGULAR SERVICE

SERVICE DATES

MAINTENANCE TASK

Before

Each Use

Every 25 Hours

or Yearly

Every 50 Hours

or Yearly

Every 100 Hours

or Yearly

Clean debris

X

Check oil level

X

Change engine oil

X

1

Change oil filter

X

Service air cleaner pre-cleaner

X²

Replace air cleaner cartridge

X²

Replace spark plug

X

Check valve clearance

X

3

Clean cooling system

X

4

Replace fuel hoses and regulator

X

5

18

www.briggsandstratton.com

Engine parts should be kept clean to reduce the risk of

overheating and ignition of accumulated debris. Use the

same instructions given above for the engine.

Oil

Oil Recommendations

NOTE: When adding oil to the engine crankcase, use

only high quality detergent oil classified “For Service SF,

SG, SH, SJ” or higher. DO NOT use special additives.

1. Choose a viscosity according to the following table:

*Check oil level frequently at higher temperatures.

NOTE: Synthetic oil meeting ILSAC GF-2, API

certification mark and API service symbol with “SJ/CF

ENERGY CONSERVING” or higher, is an acceptable oil at

all temperatures. Use of synthetic oil does not alter

required oil change intervals.

SAE 30: 40 °F and higher (5 °C and higher) is good for all

purpose use above 40°F, use below 40°F will cause hard

starting.

10W-30: 0 to 100 °F (-18 to 38 °C) is better for varying

temperature conditions. This grade of oil improves cold

weather starting, but may increase oil consumption at

80°F (27°C) or higher.

Synthetic 5W-30: -20 to 120 °F (-30 to 40 °C) provides

the best protection at all temperatures as well as

improved starting with less oil consumption.

5W-30: 40 °F and below (5 °C and below) is

recommended for winter use, and works best in cold

conditions.

Checking and Adding Oil

Oil level should be checked prior to each use or at least

every 8 hours of operation. Keep oil level maintained.

1. Make sure unit is on a level surface.

2. Remove roof (see Removable Roof and Battery

Access section).

3. Remove oil fill cap/dipstick and wipe clean with cloth.

4. Verify oil level is at the FULL mark on dipstick

(Figure 14).

5. If needed, slowly pour oil into oil fill opening.

RECHECK oil level. DO NOT overfill.

6. Replace and tighten dipstick.

7. Replace roof.

Changing Engine Oil and Filter

Remove the two screws from each plastic access cover

and remove both access covers from the two sides of the

generator enclosure.

Changing Oil

1. Slide oil drain tube from hose clamp and place oil

drain tube into approved container.

2. Push in and rotate oil drain fitting 1/4 turn

counterclockwise. Slowly pull outward until oil starts

draining (Figure 15). DO NOT pull oil drain fitting

off.

Figure 15 — Oil Drain Fitting

Figure 14 — Oil Fill Range

• DO NOT expose generator to excessive moisture, dust, dirt, or

corrosive vapors.

• DO NOT insert any objects through cooling slots.

Improper treatment of generator can damage it and

shorten its life.

CAUTION

La page est en cours de chargement...

Simplicity 040248-0 Manuel utilisateur

Ce manuel convient également à

Simplicity 040248-0 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents