Lincoln Electric Welding System 215 Manuel utilisateur

Marque: Lincoln Electric

Modèle: Welding System 215

Catégorie: Système de soudage

Taper: Manuel utilisateur

Ce manuel convient également à

POWER MIG

™

215

OPERATOR’S MANUAL

IM828-A

April, 2007

Safety Depends on You

Lincoln arc welding and cutting

equipment is designed and built

with safety in mind. However, your

overall safety can be increased by

proper installation ... and thought-

ful operation on your part. DO

NOT INSTALL, OPERATE OR

REPAIR THIS EQUIPMENT

WITHOUT READING THIS

MANUAL AND THE SAFETY

PRECAUTIONS CONTAINED

THROUGHOUT. And, most

importantly, think before you act

and be careful.

For use with machine Code Numbers

1111007700,, 1111009999,, 1111224477

For use with machine Code Numbers

• Sales and Service through Subsidiaries and Distributors Worldwide •

Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com

• World's Leader in Welding and Cutting Products •

RETURN TO MAIN MENU

FOR ENGINE

powered equipment.

1.a. Turn the engine off before troubleshooting and maintenance

work unless the maintenance work requires it to be running.

____________________________________________________

1.b.Operate engines in open, well-ventilated

areas or vent the engine exhaust fumes

outdoors.

____________________________________________________

1.c. Do not add the fuel near an open flame

welding arc or when the engine is running.

Stop the engine and allow it to cool before

refueling to prevent spilled fuel from vaporiz-

ing on contact with hot engine parts and

igniting. Do not spill fuel when filling tank. If

fuel is spilled, wipe it up and do not start

engine until fumes have been eliminated.

____________________________________________________

1.d. Keep all equipment safety guards, covers and devices in

position and in good repair.Keep hands, hair, clothing and

tools away from V-belts, gears, fans and all other moving

parts when starting, operating or repairing equipment.

____________________________________________________

1.e. In some cases it may be necessary to remove safety

guards to perform required maintenance. Remove

guards only when necessary and replace them when the

maintenance requiring their removal is complete.

Always use the greatest care when working near moving

parts.

___________________________________________________

1.f. Do not put your hands near the engine fan.

Do not attempt to override the governor or

idler by pushing on the throttle control rods

while the engine is running.

___________________________________________________

1.g. To prevent accidentally starting gasoline engines while

turning the engine or welding generator during maintenance

work, disconnect the spark plug wires, distributor cap or

magneto wire as appropriate.

SAFETY

ARC WELDING CAN BE HAZARDOUS. PROTECT YOURSELF AND OTHERS FROM POSSIBLE SERIOUS INJURY OR DEATH.

KEEP CHILDREN AWAY. PACEMAKER WEARERS SHOULD CONSULT WITH THEIR DOCTOR BEFORE OPERATING.

Read and understand the following safety highlights. For additional safety information, it is strongly recommended that you pur-

chase a copy of “Safety in Welding & Cutting - ANSI Standard Z49.1” from the American Welding Society, P.O. Box 351040,

Miami, Florida 33135 or CSA Standard W117.2-1974. A Free copy of “Arc Welding Safety” booklet E205 is available from the

Lincoln Electric Company, 22801 St. Clair Avenue, Cleveland, Ohio 44117-1199.

BE SURE THAT ALL INSTALLATION, OPERATION, MAINTENANCE AND REPAIR PROCEDURES ARE

PERFORMED ONLY BY QUALIFIED INDIVIDUALS.

WARNING

Mar ʻ95

ELECTRIC AND

MAGNETIC FIELDS

may be dangerous

2.a. Electric current flowing through any conductor causes

localized Electric and Magnetic Fields (EMF). Welding

current creates EMF fields around welding cables and

welding machines

2.b. EMF fields may interfere with some pacemakers, and

welders having a pacemaker should consult their physician

before welding.

2.c. Exposure to EMF fields in welding may have other health

effects which are now not known.

2.d. All welders should use the following procedures in order to

minimize exposure to EMF fields from the welding circuit:

2.d.1.

Route the electrode and work cables together - Secure

them with tape when possible.

2.d.2. Never coil the electrode lead around your body.

2.d.3. Do not place your body between the electrode and

work cables. If the electrode cable is on your right

side, the work cable should also be on your right side.

2.d.4. Connect the work cable to the workpiece as close as

possible to the area being welded.

2.d.5. Do not work next to welding power source.

1.h. To avoid scalding, do not remove the

radiator pressure cap when the engine is

hot.

CALIFORNIA PROPOSITION 65 WARNINGS

Diesel engine exhaust and some of its constituents

are known to the State of California to cause can-

cer, birth defects, and other reproductive harm.

The engine exhaust from this product contains

chemicals known to the State of California to cause

cancer, birth defects, or other reproductive harm.

The Above For Diesel Engines

The Above For Gasoline Engines

POWER MIG 215

SAFETY

ARC RAYS can burn.

4.a. Use a shield with the proper filter and cover

plates to protect your eyes from sparks and

the rays of the arc when welding or observing

open arc welding. Headshield and filter lens

should conform to ANSI Z87. I standards.

4.b. Use suitable clothing made from durable flame-resistant

material to protect your skin and that of your helpers from

the arc rays.

4.c. Protect other nearby personnel with suitable, non-flammable

screening and/or warn them not to watch the arc nor expose

themselves to the arc rays or to hot spatter or metal.

ELECTRIC SHOCK can

kill.

3.a. The electrode and work (or ground) circuits

are electrically “hot” when the welder is on.

Do not touch these “hot” parts with your bare

skin or wet clothing. Wear dry, hole-free

gloves to insulate hands.

3.b. Insulate yourself from work and ground using dry insulation.

Make certain the insulation is large enough to cover your full

area of physical contact with work and ground.

In addition to the normal safety precautions, if welding

must be performed under electrically hazardous

conditions (in damp locations or while wearing wet

clothing; on metal structures such as floors, gratings or

scaffolds; when in cramped positions such as sitting,

kneeling or lying, if there is a high risk of unavoidable or

accidental contact with the workpiece or ground) use

the following equipment:

• Semiautomatic DC Constant Voltage (Wire) Welder.

• DC Manual (Stick) Welder.

• AC Welder with Reduced Voltage Control.

3.c. In semiautomatic or automatic wire welding, the electrode,

electrode reel, welding head, nozzle or semiautomatic

welding gun are also electrically “hot”.

3.d. Always be sure the work cable makes a good electrical

connection with the metal being welded. The connection

should be as close as possible to the area being welded.

3.e. Ground the work or metal to be welded to a good electrical

(earth) ground.

3.f.

Maintain the electrode holder, work clamp, welding cable and

welding machine in good, safe operating condition. Replace

damaged insulation.

3.g. Never dip the electrode in water for cooling.

3.h. Never simultaneously touch electrically “hot” parts of

electrode holders connected to two welders because voltage

between the two can be the total of the open circuit voltage

of both welders.

3.i. When working above floor level, use a safety belt to protect

yourself from a fall should you get a shock.

3.j. Also see Items 6.c. and 8.

POWER MIG 215

FUMES AND GASES

can be dangerous.

5.a.Welding may produce fumes and gases

hazardous to health. Avoid breathing these

fumes and gases. When welding, keep

your head out of the fume. Use enough

ventilation and/or exhaust at the arc to keep

fumes and gases away from the breathing zone. When

welding with electrodes which require special

ventilation such as stainless or hard facing (see

instructions on container or MSDS) or on lead or

cadmium plated steel and other metals or coatings

which produce highly toxic fumes, keep exposure as

low as possible and below Threshold Limit Values (TLV)

using local exhaust or mechanical ventilation. In

confined spaces or in some circumstances, outdoors, a

respirator may be required. Additional precautions are

also required when welding on galvanized steel.

5. b. The operation of welding fume control equipment is affected

by various factors including proper use and positioning of

the equipment, maintenance of the equipment and the spe-

cific welding procedure and application involved. Worker

exposure level should be checked upon installation and

periodically thereafter to be certain it is within applicable

OSHA PEL and ACGIH TLV limits.

5.c.

Do not weld in locations near chlorinated hydrocarbon

vapors

coming from degreasing, cleaning or spraying operations.

The heat and rays of the arc can react with solvent vapors

form phosgene, a highly toxic gas, and other irritating prod-

ucts.

5.d. Shielding gases used for arc welding can displace air and

cause injury or death. Always use enough ventilation,

especially in confined areas, to insure breathing air is safe.

5.e. Read and understand the manufacturerʼs instructions for this

equipment and the consumables to be used, including the

material safety data sheet (MSDS) and follow your

employerʼs safety practices. MSDS forms are available from

your welding distributor or from the manufacturer.

5.f. Also see item 1.b.

AUG 06

FOR ELECTRICALLY

powered equipment.

8.a. Turn off input power using the disconnect

switch at the fuse box before working on

the equipment.

8.b. Install equipment in accordance with the U.S. National

Electrical Code, all local codes and the manufacturerʼs

recommendations.

8.c. Ground the equipment in accordance with the U.S. National

Electrical Code and the manufacturerʼs recommendations.

CYLINDER may explode

if damaged.

7.a. Use only compressed gas cylinders

containing the correct shielding gas for the

process used and properly operating

regulators designed for the gas and

pressure used. All hoses, fittings, etc. should be suitable for

the application and maintained in good condition.

7.b. Always keep cylinders in an upright position securely

chained to an undercarriage or fixed support.

7.c. Cylinders should be located:

•Away from areas where they may be struck or subjected to

physical damage.

•A safe distance from arc welding or cutting operations and

any other source of heat, sparks, or flame.

7.d. Never allow the electrode, electrode holder or any other

electrically “hot” parts to touch a cylinder.

7.e. Keep your head and face away from the cylinder valve outlet

when opening the cylinder valve.

7.f. Valve protection caps should always be in place and hand

tight except when the cylinder is in use or connected for

use.

7.g. Read and follow the instructions on compressed gas

cylinders, associated equipment, and CGA publication P-l,

“Precautions for Safe Handling of Compressed Gases in

Cylinders,” available from the Compressed Gas Association

1235 Jefferson Davis Highway, Arlington, VA 22202.

iii

SAFETY

iii

POWER MIG 215

Jan, 07

WELDING and CUTTING

SPARKS can

cause fire or explosion.

6.a.

Remove fire hazards from the welding area.

If this is not possible, cover them to prevent

the welding sparks from starting a fire.

Remember that welding sparks and hot

materials from welding can easily go through small cracks

and openings to adjacent areas. Avoid welding near

hydraulic lines. Have a fire extinguisher readily available.

6.b. Where compressed gases are to be used at the job site,

special precautions should be used to prevent hazardous

situations. Refer to “Safety in Welding and Cutting” (ANSI

Standard Z49.1) and the operating information for the

equipment being used.

6.c. When not welding, make certain no part of the electrode

circuit is touching the work or ground. Accidental contact

can cause overheating and create a fire hazard.

6.d. Do not heat, cut or weld tanks, drums or containers until the

proper steps have been taken to insure that such procedures

will not cause flammable or toxic vapors from substances

inside. They can cause an explosion even

though

they have

been “cleaned”. For information, purchase “Recommended

Safe Practices for the

Preparation

for Welding and Cutting of

Containers and Piping That Have Held Hazardous

Substances”, AWS F4.1 from the American Welding Society

(see address above).

6.e. Vent hollow castings or containers before heating, cutting or

welding. They may explode.

6.f.

Sparks and spatter are thrown from the welding arc. Wear oil

free protective garments such as leather gloves, heavy shirt,

cuffless trousers, high shoes and a cap over your hair. Wear

ear plugs when welding out of position or in confined places.

Always wear safety glasses with side shields when in a

welding area.

6.g. Connect the work cable to the work as close to the welding

area as practical. Work cables connected to the building

framework or other locations away from the welding area

increase the possibility of the welding current passing

through lifting chains, crane cables or other alternate cir-

cuits. This can create fire hazards or overheat lifting chains

or cables until they fail.

6.h. Also see item 1.c.

6.I. Read and follow NFPA 51B “ Standard for Fire Prevention

During Welding, Cutting and Other Hot Work”, available

from NFPA, 1 Batterymarch Park,PO box 9101, Quincy, Ma

022690-9101.

6.j. Do not use a welding power source for pipe thawing.

SAFETY

Mar. ʻ93

POWER MIG 215

PRÉCAUTIONS DE SÛRETÉ

Pour votre propre protection lire et observer toutes les instructions

et les précautions de sûreté specifiques qui parraissent dans ce

manuel aussi bien que les précautions de sûreté générales suiv-

antes:

Sûreté Pour Soudage A LʼArc

1. Protegez-vous contre la secousse électrique:

a. Les circuits à lʼélectrode et à la piéce sont sous tension

quand la machine à souder est en marche. Eviter toujours

tout contact entre les parties sous tension et la peau nue

ou les vétements mouillés. Porter des gants secs et sans

trous pour isoler les mains.

b. Faire trés attention de bien sʼisoler de la masse quand on

soude dans des endroits humides, ou sur un plancher

metallique ou des grilles metalliques, principalement dans

les positions assis ou couché pour lesquelles une grande

partie du corps peut être en contact avec la masse.

c. Maintenir le porte-électrode, la pince de masse, le câble

de soudage et la machine à souder en bon et sûr état

defonctionnement.

d.Ne jamais plonger le porte-électrode dans lʼeau pour le

refroidir.

e. Ne jamais toucher simultanément les parties sous tension

des porte-électrodes connectés à deux machines à souder

parce que la tension entre les deux pinces peut être le

total de la tension à vide des deux machines.

f. Si on utilise la machine à souder comme une source de

courant pour soudage semi-automatique, ces precautions

pour le porte-électrode sʼapplicuent aussi au pistolet de

soudage.

2. Dans le cas de travail au dessus du niveau du sol, se protéger

contre les chutes dans le cas ou on recoit un choc. Ne jamais

enrouler le câble-électrode autour de nʼimporte quelle partie

du corps.

3. Un coup dʼarc peut être plus sévère quʼun coup de soliel,

donc:

a. Utiliser un bon masque avec un verre filtrant approprié

ainsi quʼun verre blanc afin de se protéger les yeux du ray-

onnement de lʼarc et des projections quand on soude ou

quand on regarde lʼarc.

b. Porter des vêtements convenables afin de protéger la

peau de soudeur et des aides contre le rayonnement de

lʻarc.

c. Protéger lʼautre personnel travaillant à proximité au

soudage à lʼaide dʼécrans appropriés et non-inflammables.

4. Des gouttes de laitier en fusion sont émises de lʼarc de

soudage. Se protéger avec des vêtements de protection libres

de lʼhuile, tels que les gants en cuir, chemise épaisse, pan-

talons sans revers, et chaussures montantes.

5. Toujours porter des lunettes de sécurité dans la zone de

soudage. Utiliser des lunettes avec écrans lateraux dans les

zones où lʼon pique le laitier.

6. Eloigner les matériaux inflammables ou les recouvrir afin de

prévenir tout risque dʼincendie dû aux étincelles.

7. Quand on ne soude pas, poser la pince à une endroit isolé de

la masse. Un court-circuit accidental peut provoquer un

échauffement et un risque dʼincendie.

8. Sʼassurer que la masse est connectée le plus prés possible

de la zone de travail quʼil est pratique de le faire. Si on place

la masse sur la charpente de la construction ou dʼautres

endroits éloignés de la zone de travail, on augmente le risque

de voir passer le courant de soudage par les chaines de lev-

age, câbles de grue, ou autres circuits. Cela peut provoquer

des risques dʼincendie ou dʼechauffement des chaines et des

câbles jusquʼà ce quʼils se rompent.

9. Assurer une ventilation suffisante dans la zone de soudage.

Ceci est particuliérement important pour le soudage de tôles

galvanisées plombées, ou cadmiées ou tout autre métal qui

produit des fumeés toxiques.

10. Ne pas souder en présence de vapeurs de chlore provenant

dʼopérations de dégraissage, nettoyage ou pistolage. La

chaleur ou les rayons de lʼarc peuvent réagir avec les vapeurs

du solvant pour produire du phosgéne (gas fortement toxique)

ou autres produits irritants.

11. Pour obtenir de plus amples renseignements sur la sûreté,

voir le code “Code for safety in welding and cutting” CSA

Standard W 117.2-1974.

PRÉCAUTIONS DE SÛRETÉ POUR

LES MACHINES À SOUDER À

TRANSFORMATEUR ET À

REDRESSEUR

1. Relier à la terre le chassis du poste conformement au code de

lʼélectricité et aux recommendations du fabricant. Le dispositif

de montage ou la piece à souder doit être branché à une

bonne mise à la terre.

2. Autant que possible, Iʼinstallation et lʼentretien du poste seront

effectués par un électricien qualifié.

3. Avant de faires des travaux à lʼinterieur de poste, la debranch-

er à lʼinterrupteur à la boite de fusibles.

4. Garder tous les couvercles et dispositifs de sûreté à leur

place.

TThhaannkk YYoouu

for selecting a QUALITY product by Lincoln Electric. We want you

to take pride in operating this Lincoln Electric Company product

••• as much pride as we have in bringing this product to you!

Read this Operators Manual completely before attempting to use this equipment. Save this manual and keep it

handy for quick reference. Pay particular attention to the safety instructions we have provided for your protection.

The level of seriousness to be applied to each is explained below:

WARNING

This statement appears where the information must be followed exactly to avoid serious personal injury or loss of life.

This statement appears where the information must be followed to avoid minor personal injury or damage to this equipment.

CAUTION

Please Examine Carton and Equipment For Damage Immediately

When this equipment is shipped, title passes to the purchaser upon receipt by the carrier. Consequently, Claims

for material damaged in shipment must be made by the purchaser against the transportation company at the

time the shipment is received.

Please record your equipment identification information below for future reference. This information can be

found on your machine nameplate.

Product _________________________________________________________________________________

Model Number ___________________________________________________________________________

Code Number or Date Code_________________________________________________________________

Serial Number____________________________________________________________________________

Date Purchased___________________________________________________________________________

Where Purchased_________________________________________________________________________

Whenever you request replacement parts or information on this equipment, always supply the information you

have recorded above. The code number is especially important when identifying the correct replacement parts.

On-Line Product Registration

- Register your machine with Lincoln Electric either via fax or over the Internet.

• For faxing: Complete the form on the back of the warranty statement included in the literature packet

accompanying this machine and fax the form per the instructions printed on it.

• For On-Line Registration: Go to our

WEB SITE at www.lincolnelectric.com. Choose “Quick Links” and then

“Product Registration”. Please complete the form and submit your registration.

CUSTOMER ASSISTANCE POLICY

The business of The Lincoln Electric Company is manufacturing and selling high quality welding equipment, consumables, and cutting equip-

ment. Our challenge is to meet the needs of our customers and to exceed their expectations. On occasion, purchasers may ask Lincoln

Electric for advice or information about their use of our products. We respond to our customers based on the best information in our posses-

sion at that time. Lincoln Electric is not in a position to warrant or guarantee such advice, and assumes no liability, with respect to such infor-

mation or advice. We expressly disclaim any warranty of any kind, including any warranty of fitness for any customerʼs particular purpose,

with respect to such information or advice. As a matter of practical consideration, we also cannot assume any responsibility for updating or

correcting any such information or advice once it has been given, nor does the provision of information or advice create, expand or alter any

warranty with respect to the sale of our products.

Lincoln Electric is a responsive manufacturer, but the selection and use of specific products sold by Lincoln Electric is solely within the control

of, and remains the sole responsibility of the customer. Many variables beyond the control of Lincoln Electric affect the results obtained in

applying these types of fabrication methods and service requirements.

Subject to Change – This information is accurate to the best of our knowledge at the time of printing. Please refer to www.lincolnelectric.com

for any updated information.

vi vi

MASTER TABLE OF CONTENTS FOR ALL SECTIONS

Page

________________________________________________________________________

Installation .......................................................................................................Section A

Technical Specifications........................................................................................A-1

Safety Precautions.................................................................................................A-2

Uncrating the POWER MIG 215............................................................................A-2

Location.................................................................................................................A-2

Input Power, Grounding and connection Diagrams.................................A-2 thru A-3

Output Polarity Connections..................................................................................A-3

Gun and Cable Installation ....................................................................................A-4

Shielding Gas ........................................................................................................A-4

________________________________________________________________________

Operation .........................................................................................................Section B

Safety Precautions.................................................................................................B-1

Product Description ...............................................................................................B-2

Recommended Processes and Equipment ...........................................................B-2

Welding Capability.................................................................................................B-2

Limitations..............................................................................................................B-2

Description of Controls ..........................................................................................B-2

Wire Drive Roll.......................................................................................................B-2

Wire Size Conversion parts...................................................................................B-2

Procedure for Changing Drive Roll........................................................................B-3

Wire Reel Loading.................................................................................................B-3

Mounting of 10 to 30 lbs. Spools ...........................................................................B-3

To Start the Welder................................................................................................B-3

Feeding Electrode..................................................................................................B-4

Idle Roll Pressure Setting......................................................................................B-4

Wire Drive Configuration................................................................................B-4, B-5

Making a Weld.......................................................................................................B-5

Avoiding Wire Feeding Problems ..........................................................................B-6

Fan Control............................................................................................................B-6

Input Line Voltage Protection.................................................................................B-6

Wire Feed overload Protection..............................................................................B-6

Welding Thermal Overload Protection...................................................................B-6

________________________________________________________________________

Accessories.....................................................................................................Section C

Drive Roll Kits........................................................................................................C-1

Aluminum Feeding Kit (Optional K1703-1)............................................................C-1

K363P Readi-Reel Adapter...................................................................................C-1

Dual Cylinder Mounting Kit (K1702-1)...................................................................C-1

Alternative Magnum GMAW Gun and Cable Assemblies .....................................C-1

Magnum Gun Connection Kit (Optional K466-6)...................................................C-1

Spool Gun and Adapter Kit (Optional K1809-1) ....................................................C-1

Making a Weld with the Spool Gun Adapter Kit and Spool Gun Installed.............C-2

________________________________________________________________________

POWER MIG 215

vii vii

MASTER TABLE OF CONTENTS FOR ALL SECTIONS (cont.)

Page

Maintenance ....................................................................................................Section D

Safety Precautions ................................................................................................D-1

General Maintenance............................................................................................D-1

Drive Rolls and guide Tubes .................................................................................D-1

Contact Tip and Gas Nozzle Installation ...............................................................D-1

Gun Tubes and Nozzles........................................................................................D-1

Gun Cable Cleaning..............................................................................................D-1

Liner Removal and Replacement..........................................................................D-2

Gun Handle Disassembly......................................................................................D-3

Troubleshooting..............................................................................................Section E

How to Use Troubleshooting Guide.......................................................................E-1

Troubleshooting Guide ............................................................................E-2 thru E-4

Wiring Diagram and Dimension Print............................................................Section F

Parts Manual....................................................................................................Appendix

POWER MIG 215 ..............................................................................................P-487

Magnum 250L Gun ....................................................................................P-202-H.2

POWER MIG 215

A-1

INSTALLATION

75°C Copper Wire 75°C Copper Wire

Input Ampere in Conduit in Conduit

Input Voltage/ Fuse or Breaker Rating On AWG (IEC) Sizes AWG (IEC) Sizes

(For lengths (For lengths

Frequency (Hz) Size (Super Lag) Nameplate up to 100 ft.) exceeding 100 ft.)

208/50/60 60 45A 10 (6 mm

) 8 (10 mm

)

230/50/60 60 41A 10 (6 mm

) 8 (10 mm

)

NOTE: Use #10 AWG Grounding Wire

TECHNICAL SPECIFICATIONS – POWER MIG 215

INPUT – SINGLE PHASE ONLY

RATED OUTPUT

OUTPUT

RECOMMENDED INPUT WIRE AND FUSE SIZES

Height Width Depth Weight

31.79 in 18.88 in 38.78 in 210 Ibs

808 mm 480 mm 985 mm 95 kg

PHYSICAL DIMENSIONS

Wire Speed 50 – 700 IPM (1.27 – 17.8 m/minute)

WIRE SPEED RANGE

Standard Voltage/Phase/Frequency

Input Current @ 170 Amp Rated Output Input Current @ 215 Amp Rated Output

208/230/1/50/60 Hz

(With 115V receptacle loaded to 15A) (With 115V receptacle loaded to 15A)

39/35 Amps 45/41 Amps

Duty Cycle Amps Volts at Rated Amperes

30% 215 Amps 22 Volts

40% 190 Amps 23 Volts

60% 170 Amps 24 Volts

Welding Current Range Maximum Open Circuit Voltage Welding Voltage Range

30 – 250Amps 35 Volts 13.5-24 Volts

POWER MIG 215

TEMPERATURE RANGES

STORAGE TEMPERATURE RANGE

-40°F to 185°F(-40°C to +40°C)

OPERATING TEMPERATURE RANGE

-4°F to 104°F(-20°C to +40°C)

A-2

INSTALLATION

Read entire installation section before starting

installation.

SAFETY PRECAUTIONS

POWER MIG 215

INPUT POWER, GROUNDING AND

CONNECTION DIAGRAMS

1. Before starting the installation, check with the local

power company if there is any question about

whether your power supply is adequate for the volt-

age, amperes, phase, and frequency specified on

the welder nameplate. Also be sure the planned

installation will meet the U.S. National Electrical

Code and local code requirements. This welder

may be operated from a single phase line or from

one phase of a two or three phase line.

2. Models that have multiple input voltages specified

on the nameplate (e.g. 208/230) are shipped con-

nected for the highest voltage. If the welder is to be

operated on lower voltage, it must be reconnected

according to the instructions in Figure A.1 for dual

voltage machines.

Make certain that the input power is electrically

disconnected before removing the screw on the

reconnect panel access cover.

------------------------------------------------------------------------

UNCRATING THE POWER MIG 215

Cut banding and lift off cardboard carton. Cut banding

holding the machine to the skid. Remove foam and

corrugated packing material. Untape accessories from

Gas Bottle Platform. Unscrew the two wood screws

(at the Gas Bottle Platform) holding the machine to

the skid. Roll the machine off the skid assembly.

LOCATION

Locate the welder in a dry location where there is free

circulation of clean air into the louvers in the back and

out the front. A location that minimizes the amount of

smoke and dirt drawn into the rear louvers reduces

the chance of dirt accumulation that can block air pas-

sages and cause overheating.

ELECTRIC SHOCK can kill.

• Only qualified personnel should

perform this installation.

• Only personnel that have read

and understood the POWER MIG

215 Operating Manual should

install and operate this equip-

ment.

• Machine must be grounded per

any national, local or other applic-

able electrical codes.

• The POWER MIG power switch is

to be in the OFF position when

installing work cable and gun and

when connecting other equip-

ment.

WARNING

ELECTRIC SHOCK can kill.

• Do not touch electrically live parts such as

output terminals or internal wiring.

• All input power must be electrically dis-

connected before proceeding.

WARNING

3. The 208/230 volt 50/60 Hz model POWER MIG is

shipped with a 7 ft.(2.1m). input cable and plug

connected to the welder.

4. Using the instructions in Figure A.2, have a quali-

fied electrician connect a receptacle (Customer

Supplied) or cable to the input power lines and the

system ground per the U.S. National Electrical

Code and any applicable local codes. See

“Technical Specifications” at the beginning of this

chapter for proper wire sizes. For long runs over

100 feet, larger copper wires should be used. Fuse

the two hot lines with super lag type fuses as

shown in the following diagram. The center contact

in the receptacle is for the grounding connection. A

green wire in the input cable connects this contact

to the frame of the welder. This ensures proper

grounding of the welder frame when the welder

plug is inserted into a grounded receptacle.

FIGURE A.2 — Receptacle Diagram

CONNECT TO A SYSTEM

GROUNDING WIRE. SEE

THE UNITED STATES

NATIONAL ELECTRICAL

CODE AND/OR LOCAL

CODES FOR OTHER

DETAILS AND MEANS FOR

PROPER GROUNDING.

CONNECT TO HOT WIRES

OF A THREE-WIRE, SINGLE

PHASE SYSTEM.

A-3 A-3

INSTALLATION

POWER MIG 215

50/60 HZ

FIGURE A.1 — Dual Voltage Machine Input Connections

OUTPUT POLARITY CONNECTIONS

The welder, as shipped from the factory, is connected

for electrode positive (+) polarity. This is the normal

polarity for GMA welding.

If negative (–) polarity is required, interchange the

connection of the two cables located in the wire drive

compartment near the front panel. The electrode

cable, which is attached to the wire drive, is to be con-

nected to the negative (–) labeled terminal and the

work lead, which is attached to the work clamp, is to

be connected to the positive (+) labeled terminal.

GUN AND CABLE INSTALLATION

The Magnum 250L gun and cable provided with the

POWER MIG 215 is factory installed with a liner for

.035-.045" (0.9-1.2 mm) electrode and an .035" (0.9

mm) contact tip. Be sure that the contact tip, liner, and

drive rolls all match the size of the wire being used.

Turn the welder power switch off before installing

gun and cable.

1. Lay the cable out straight.

2. Unscrew knurled screw on the drive unit front end

(inside wire feed compartment) until tip of screw no

longer protrudes into gun opening as seen from

front of machine.

3. Insert the male end of gun cable into the Gun

Adapter casting through opening in front panel.

Make sure connector is fully inserted and tighten

knurled screw.

4. Connect the gun trigger connector from the gun

and cable to the mating receptacle inside the com-

partment located above the gun connection made

in item 3 above. Make sure that the keyways are

aligned, insert and tighten retaining ring.

SHIELDING GAS

(For Gas Metal Arc Welding Processes)

Customer must provide cylinder of appropriate type

shielding gas for the process being used.

A gas flow regulator, for Argon blend gas, and an inlet

gas hose are factory provided with the POWER MIG

215. When using 100% CO

an additional adapter will

be required to connect the regulator to the gas bottle.

Install shielding gas supply as follows:

1. Set gas cylinder on rear platform of POWER MIG

215. Hook chain in place to secure cylinder to rear

of welder.

WARNING

A-4

INSTALLATION

WARNING

2. Remove the cylinder cap. Inspect the cylinder

valves and regulator for damaged threads, dirt,

dust, oil or grease. Remove dust and dirt with a

clean cloth.

DO NOT ATTACH THE REGULATOR IF OIL,

GREASE OR DAMAGE IS PRESENT! Inform your

gas supplier of this condition. Oil or grease in the

presence of high pressure oxygen is explosive.

3. Stand to one side away from the outlet and open

the cylinder valve for an instant. This blows away

any dust or dirt which may have accumulated in the

valve outlet.

Be sure to keep your face away from the valve

outlet when “cracking” the valve.

4. Attach the flow regulator to the cylinder valve and

tighten the union nut(s) securely with a wrench.

NOTE: If connecting to 100% CO

cylinder, an

additional regulator adapter must be installed

between the regulator and cylinder valve. If adapter

is equipped with a plastic washer, be sure it is seat-

ed for connection to the CO

cylinder.

5. Attach one end of the inlet gas hose to the outlet

fitting of the flow regulator, the other end to the

POWER MIG 215 rear fitting, and tighten the union

nuts securely with a wrench.

6. Before opening the cylinder valve, turn the regula-

tor adjusting knob counterclockwise until the

adjusting spring pressure is released.

7. Standing to one side, open the cylinder valve slow-

ly a fraction of a turn. When the cylinder pressure

gauge pointer stops moving, open the valve fully.

Never stand directly in front of or behind the flow

regulator when opening the cylinder valve. Always

stand to one side.

___________________________________________

8. The flow regulator is adjustable. Adjust it to the flow

rate recommended for the procedure and process

being used before making the weld.

AUXILIARY POWER RECEPTACLES

(15 Amp 120 Volt Receptacle) The receptacles are UL

and CSA approved.

CYLINDER may explode if

damaged.

• Gas under pressure is explosive. Always

keep gas cylinders in an upright position

and always keep chained to undercarriage

or stationary support. See American

National Standard Z-49.1, “Safety in

Welding and Cutting” published by the

American Welding Society.

WARNING

POWER MIG 215

WARNING

B-1

OPERATION

Read entire Operation section before

operating the POWER MIG 215.

ELECTRIC SHOCK can kill.

• Do not touch electrically live

parts or electrode with skin or wet

clothing. Insulate yourself from

work and ground.

• Always wear dry insulating

gloves.

FUMES AND GASES can be

dangerous.

• Keep your head out of fumes.

• Use ventilation or exhaust to

remove fumes from breathing

zone.

WELDING SPARKS can

cause fire or explosion.

• Keep flammable material away.

• Do not weld on closed containers.

ARC RAYS can burn eyes

and skin.

• Wear eye, ear and body protec-

tion.

Observe all safety information throughout

this manual.

WARNING

POWER MIG 215

B-2 B-2

OPERATION

PRODUCT DESCRIPTION

The POWER MIG™ 215 is a complete semiautomatic

DC voltage arc welding machine built to meet NEMA

specifications. It combines a tapped transformer volt-

age power source with a constant speed wire feeder

to form a reliable robust performance welding system.

A simple control scheme, consisting of continuous full

range wire feed speed control, and 7 output voltage

tap selections provides versatility with ease of use and

accuracy.

Other features include a 2" (51 mm) O.D. wire reel

spindle with adjustable brake, an integral gas cylinder

mounting undercarriage, an adjustable Argon blend

flow regulator with cylinder pressure gauge and inlet

hose, a 15 ft. (3.6 m) Magnum 250L GMAW gun and

cable with fixed (flush) nozzle, a 7 ft. (2.1 m) power

cable with plug, and a 10 ft. (3.0 m) work cable with

clamp.

Optional Spool Gun and Adapter kit, Dual Cylinder

Mounting kit and Aluminum Feeding Kit for push feed-

ing with standard built in feeder are also available.

RECOMMENDED PROCESSES AND

EQUIPMENT

The POWER MIG 215 is recommended for GMA

welding processes using 10 to 44 lb (4.5 to 20 kg) 2"

(51 mm) I.D. spools or Readi-Reel

coils (with option-

al adapter) of .025" through .045" (0.6 – 1.2 mm) solid

steel, .035" (0.9 mm) stainless, 3/64" (1.2 mm) alu-

minum and .035 (0.9 mm), .045" (1.2 mm)

Outershield

; as well as .035" (0.9 mm) and .045" (1.2

mm) Innershield

self-shielding electrodes.

The POWER MIG is factory equipped to feed .035"

(0.9 mm) electrodes. It also includes a 200A, 60%

duty cycle (or 250A, 40% duty cycle) rated, 15 ft. (3.6

m) GMAW gun and cable assembly equipped for

these wire sizes. Use of GMAW processes requires a

supply of shielding gas.

WELDING CAPABILITY

The POWER MIG 215 is rated at 215 amps @ 22

volts, at a 30% duty cycle based on a ten minute cycle

time. It is capable of higher duty cycles at lower output

currents. The tapped transformer design makes it

well suited for use with most portable or in-plant gen-

erating systems.

LIMITATIONS

The output voltage/current of the POWER MIG 215 is

subject to vary if the input power to the machine

varies, due to its tapped transformer power topology.

In some cases an adjustment of WFS preset and/or

voltage tap selection may be required to accommo-

date a significant drift in input power.

DESCRIPTION OF CONTROLS

See Figure B.1

1. Power ON/OFF Switch — Place the lever in the

"ON" position to energize the POWER MIG 215.

2. Voltage Control — Seven voltage tap selections

are provided Labeled "A" (minimum voltage)

through "G" (maximum voltage). It should only be

adjusted when not welding. The control selection

can be preset to the setting specified on the

Procedure Decal on the inside of the wire compart-

ment door.

3. Wire Speed Control — This controls the wire feed

speed from 50 – 700 inches per minute (1.2 – 17.8

m/min). Wire speed is not affected when changes

are made in the voltage control.

FIGURE B.1

WIRE DRIVE ROLL

The drive rolls installed with the POWER MIG have

two grooves one for .035(0.9mm) wire and the other

for .045(1.2mm) wire. Drive roll size is indicated by the

stenciling on the exposed side of the drive roll.

WIRE SIZE CONVERSION PARTS

The POWER MIG 215 is rated to feed .025 through

.045" (0.6-1.2 mm) solid or cored electrode sizes.

The drive roll kits and Magnum 250L gun and cable

parts are available to feed different sizes and types of

electrodes. See Accessories section.

POWER MIG 215

B-3 B-3

OPERATION

PROCEDURE FOR CHANGING

DRIVE AND IDLE ROLL SETS

1. Turn off the power source.

2. Release the pressure on the idle roll by swinging

the adjustable pressure arm down toward the back

of the machine. Lift the cast idle roll assembly and

allow it to sit in an upright position..

3. Remove the outside wire guide retaining plate by

loosening the two large knurled screws.

4. Twist the drive roll retaining mechanism to the

unlocked position as shown below and remove the

drive rolls. (See FigureB.2)

5. Remove the inside wire guide plate.

6. Replace the drive rolls and inside wire guide with a

set marked for the new wire size. NOTE: Be sure

that the gun liner and contact tip are also sized to

match the selected wire size.

7. Manually feed the wire from the wire reel, over the

drive roll groove and through the wire guide and

then into the brass bushing of the gun and cable

assembly.

8. Replace the outside wire guide retaining plate by

tightening the two large knurled screws. Reposition

the adjustable pressure arm to its original position

to apply pressure. Adjust pressure as necessary.

WIRE REEL LOADING - READI-REELS,

SPOOLS OR COILS

To Mount a 30 Lb. (14 kg) Readi-Reel Package

(Using the Molded Plastic K363-P Readi-Reel

Adapter:)

1. Open the Wire Drive Compartment Door

2. Depress the Release Bar on the Retaining Collar and

remove it from the spindle.

3. Place the Optional Adapter on the spindle

4. Re-install the Retaining Collar. Make sure that the

Release Bar “pops up” and that the collar retainers fully

engage the retaining ring groove on the spindle.

5. Rotate the spindle and adapter so the retaining spring is

at the 12 o'clock position.

6. Position the Readi-Reel so that it will rotate in a direction

when feeding so as to be de- reeled from top of the coil.

7. Set one of the Readi-Reel inside cage wires on the slot

in the retaining spring tab.

8. Lower the Readi-Reel to depress the retaining spring and

align the other inside cage wires with the grooves in the

molded adapter.

9. Slide cage all the way onto the adapter until the retaining

spring "pops up" fully.

CHECK TO BE SURE THE RETAINING SPRING HAS FULLY

RETURNED TO THE LOCKING POSITION AND HAS SECURELY

LOCKED THE READI-REEL CAGE IN PLACE. RETAINING SPRING

MUST REST ON THE CAGE, NOT THE WELDING ELECTRODE.

-----------------------------------------------------------------------------------------------

10. To remove Readi-Reel from Adapter, depress retaining

spring tab with thumb while pulling the Readi-Reel cage

from the molded adapter with both hands. Do not

remove adapter from spindle.

FIGURE B.1

To Mount 10 to 44 Lb. (4.5-20 kg) Spools (12"/300

mm Diameter) or 14Lb.(6 Kg) Innershield Coils:

(For 13-14 lb. (6 Kg) Innershield coils, a K435 Coil Adapter must be

used).

. Open the Wire Drive Compartment Door

2. Depress the Release Bar on the Retaining Collar and

remove it from the spindle.

3. Place the spool on the spindle making certain the spindle

brake pin enters one of the holes in the back side of the

spool (Note: an arrow mark on the spindle lines up with

the brake holding pin to assist in lining up a hole). Be

certain the wire comes off the reel in a direction so as to

de-reel from the top of the coil.

4. Re-install the Retaining Collar. Make sure that the

Release Bar “pops up” and that the collar retainers fully

engage the retaining ring groove on the spindle.

TO START THE WELDER

Turn the “Power Switch” switch to “ON”. With the desired voltage

and wire speed selected, operate the gun trigger for welder output

and to energize the wire feed motor.

CAUTION

POWER MIG 215

LOCKED POSITION

UNLOCKED POSITION

FIGURE B.2

B-4 B-4

OPERATION

FEEDING WIRE ELECTRODE

When triggering, the electrode and

drive mechanism are electrically “hot”

relative to work and ground and

remain “hot” several seconds after

the gun trigger is released.

------------------------------------------------------------------------

NOTE: Check that drive rolls, guide plates and gun

parts are proper for the wire size and type being used.

Refer to Table C.1 in Accessories section.

1. Turn the Readi-Reel or spool until the free end of

the electrode is accessible.

2. While securely holding the electrode, cut off the

bent end and straighten the first six inches. (If the

electrode is not properly straightened, it may not

feed properly through the wire drive system).

3. Release the pressure on the idle roll by swinging

the adjustable pressure arm down toward the back

of the machine. Lift the cast idle roll assembly and

allow it to sit in an upright position. Leave the outer

wire guide plate installed. Manually feed the wire

through the incoming guide bushing and through

the guide plates (over the drive roll groove). Push a

sufficient wire length to assure that the wire has fed

into the gun and cable assembly without restriction.

Reposition the adjustable pressure arm to its origi-

nal position to apply pressure to the wire.

4. Press gun trigger to feed the electrode wire through

the gun.

IDLE ROLL PRESSURE SETTING

ELECTRIC SHOCK can kill.

• Turn the input power OFF at the weld-

ing power source before installation or

changing drive rolls and/or guides.

• Do not touch electrically live parts.

• When inching with the gun trigger, electrode

and drive mechanism are "hot" to work and

ground and could remain energized several sec-

onds after the gun trigger is released.

• Only qualified personnel should perform mainte-

nance work.

------------------------------------------------------------------------

The pressure arm controls the amount of force the drive

rolls exert on the wire. Proper adjustment of both pres-

sure arm gives the best welding performance. For best

results, set both pressure arms to the same value.

Set the pressure arm as follows (See Figure B.2a):

Aluminum wires between 1 and 3

Cored wires between 3 and 4

Steel, Stainless wires between 4 and 6

WIRE DRIVE CONFIGURATION

(See Figure B.2b)

Changing the Gun Receiver Bushing

ELECTRIC SHOCK can kill.

• Turn the input power OFF at the weld-

ing power source before installation or

changing drive rolls and/or guides.

• Do not touch electrically live parts.

• When inching with the gun trigger, electrode

and drive mechanism are "hot" to work and

ground and could remain energized several sec-

onds after the gun trigger is released.

• Only qualified personnel should perform mainte-

nance work.

-----------------------------------------------------------------------

Tools required:

• 1/4" hex key wrench.

Note: Some gun bushings do not require the use of

the thumb screw.

1. Turn power off at the welding power source.

2. Remove the welding wire from the wire drive.

3. Remove the thumb screw from the wire drive.

4. Remove the welding gun from the wire drive.

WARNING

POWER MIG 215

ALUMINUM

OUTERSHIELD

METALSHIELD

INNERSHIELD

STEEL

TAINLESS

CORED WIRES

SOLID WIRES

B-5 B-5

OPERATION

3. Press the trigger to feed the wire electrode through

the gun and cable. For solid wire cut the electrode

within approximately 3/8" (10 mm) of the end of the

contact tip [3/4" (20 mm) for Outershield

4. When welding with gas, turn on the gas supply and

set the required flow rate (typically 25-35 CFH; 12-

16 liters/min).

5. Connect work cable to metal to be welded. Work

clamp must make good electrical contact to the

work. The work must also be grounded as stated in

“Arc Welding Safety Precautions”.

• When using an open arc process, it

is necessary to use correct eye,

head, and body protection.

-----------------------------------------------------------------------

6. Position electrode over joint. End of electrode may

be lightly touching the work.

7. Lower welding helmet, close gun trigger, and

begin welding. Hold the gun so the contact tip to

work distance is about 3/8" (10 mm) [3/4" (20 mm)

for Outershield

8. To stop welding, release the gun trigger and then

pull the gun away from the work after the arc goes

out.

POWER MIG 215

GUN RECEIVER BUSHING

LOOSEN TIGHTEN

THUMB SCREW

OUTER WIRE GUIDE

SOCKET HEAD

CAP SCREW

CONNECTOR BLOCK

WARNING

5. Loosen the socket head cap screw that holds the

connector bar against the gun bushing.

Important: Do not attempt to completely

remove the socket head cap screw.

6. Remove the outer wire guide, and push the gun

bushing out of the wire drive. Because of the pre-

cision fit, light tapping may be required to remove

the gun bushing.

7. Disconnect the shielding gas hose from the gun

bushing, if required.

8. Connect the shielding gas hose to the new gun

bushing, if required.

9. Rotate the gun bushing until the thumb screw hole

aligns with the thumb screw hole in the feed plate.

Slide the gun receiver bushing into the wire drive

and verify the thumb screw holes are aligned.

10. Tighten the socket head cap screw.

11. Insert the welding gun into the gun bushing and

tighten the thumb screw.

MAKING A WELD

1. Check that the electrode polarity is correct for the

process being used, then turn the power switch ON.

2. Set desired arc voltage tap and wire speed for the

particular electrode wire, material type and thick-

ness, and gas (for MIG and Outershield

) being

used. Use the Application Chart on the door inside

the wire compartment as a quick reference for

some common welding procedures.

Figure B.2b

B-6 B-6

OPERATION

9. When no more welding is to be done, close valve

on gas cylinder (if used), momentarily operate gun

trigger to release gas pressure, and turn off

POWER MIG 215.

NOTE: When using Innershield electrode, the gas

nozzle may be removed from the insulation on

the end of the gun and replaced with the gas-

less nozzle. This will give improved visibility

and eliminate the possibility of the gas nozzle

overheating.

AVOIDING WIRE FEEDING

PROBLEMS

Wire feeding problems can be avoided by observing

the following gun handling procedures:

1. Do not kink or pull cable around sharp corners.

2. Keep the gun cable as straight as possible when

welding or loading electrode through cable.

3. Do not allow dolly wheels or trucks to run over

cables.

4. Keep cable clean by following maintenance instruc-

tions.

5. Use only clean, rust-free electrode. The Lincoln

electrodes have proper surface lubrication.

6. Replace contact tip when the arc starts to become

unstable or the contact tip end is fused or

deformed.

7. Keep wire reel spindle brake tension to minimum

required to prevent excess reel over-travel which

may cause wire “loop-offs” from coil.

8. Use proper drive rolls and wire drive idle roll pres-

sure for wire size and type being used.

FAN CONTROL

The fan is designed to come on when input power is

applied to the POWER MIG 215 and go off when

power is removed.

INPUT LINE VOLTAGE VARIATIONS

High Line Voltage — Higher than rated input voltage

will result in output voltages higher than normal for a

given tap setting. If your input line is high, you may

want to select a lower voltage tap than given on the

recommended procedure chart.

Low Line Voltage — You may not be able to get

maximum output from the machine if the line voltage

is less than rated input. The unit will continue to weld,

but the output may be less than normal for a given tap

setting. If your input line is low, you may want to select

a higher voltage tap than given on the recommended

procedure chart.

WIRE FEED OVERLOAD

PROTECTION

The POWER MIG has solid state overload protection

of the wire drive motor. If the motor becomes over-

loaded, the protection circuitry turns off the wire feed

speed and gas solenoid. Check for proper size tip,

liner, and drive rolls, for any obstructions or bends in

the gun cable, and any other factors that would

impede the wire feeding. to resume welding, simply

pull the trigger. There is no circuit breaker to reset, as

the protection is done with reliable solid state electron-

ics.

WELDING THERMAL OVERLOAD

PROTECTION

The POWER MIG 215 has built-in protective ther-

mostats that respond to excessive temperature. They

open the wire feed and welder output circuits if the

machine exceeds the maximum safe operating tem-

perature because of a frequent overload, or high

ambient temperature plus overload. The thermostats

automatically reset when the temperature reaches a

safe operating level and welding and feeding are

allowed again, when gun is retriggered.

Wire Feed Speed/Voltage Tap Settings

Wire Dia. Gas Type Wire Type

Polarity 18 gage 16 gage14 gage 12 gage10gage 3/16 1/4 5/16 3/8 1/2

Outershield

1" CTWD

†

.035 75Ar/25CO

OS71M DC+

250/D 300/E 350/F 500/G *500/G

.035 100%CO

OS71M DC+

300/E 350/F 500/G

.045 75Ar/25CO

OS71M DC+

200/E 225/F 250/G 250/G *250/G

Innershield

5/8" CTWD

†

.035 NoneReqʼd NR-211MP DC-

50/B 70/B 80/B 90/C 100/C

.045 NoneReqʼd NR-211MP DC-

50/B 70/C 90/C 110/D

**130/E

.045 NoneReqʼd NR212 DC-

40/B 50/B 60/B 65/C 70/C 90/C 110/D

*130/E *150/E *150/E

POWER MIG 215

PROCEDURE CHART

†

Contact Tip to Work Distance

* Note- Requires Multiple Pass

**.035 & .045 NR-211 MP are only recommended for a maximum steel thickness of 5/16"

C-1 C-1

ACCESSORIES

DRIVE ROLL KITS

Refer to Table C.1 for various drive roll kits that are

available for the POWER MIG 215.The item in Bold is

supplied standard with the POWER MIG 215.

TABLE C.1

3/64" (1.2 mm) ALUMINUM

FEEDING KIT (K1703-1)

This kit helps push feeding aluminum through stan-

dard machine feeder and gun. It provides gun and

wire drive conversion parts to weld with 3/64" (1.2

mm) aluminum wire. 5356 alloy aluminum wire is rec-

ommended for best push feeding performance.

Kit includes drive rolls and wire guide plate for the

wire drive, liner and two contact tips for the gun, along

with installation instructions.

READI-REEL ADAPTER (K363P)

The K363P Readi-Reel Adapter mounts to the 2" spin-

dle. It is needed to mount the 22-30 lb. Readi-Reels.

DUAL CYLINDER MOUNTING KIT

(K1702-1)

Permits stable side-by-side mounting of two full size

228.6mm dia x 1.524m high(9" dia. x 5' high) gas

cylinders with “no lift” loading. Simple installation and

easy instructions provided. Includes upper and lower

cylinder supports, wheel axles and mounting hard-

ware.

SMALL SPOOL SPINDLE ADAPTER

(K468)

The K468 spindle adapter allows the use of 8" diamter

small spools.

ALTERNATIVE MAGNUM GMAW

GUN AND CABLE ASSEMBLIES

The following Magnum 250L gun and cable assem-

blies are separately available for use with the POWER

MIG 215. Each is rated 250 amps 40% duty cycle and

is equipped with the integrated connector, twist-lock

trigger connector, fixed nozzle and insulator, and

includes a liner, diffuser, and contact tips for the wire

sizes specified:

MAGNUM GUN CONNECTION KIT

(Optional K466-6)

Using the optional K466-6 Magnum Connection kit for

the POWER MIG permits use of standard Magnum

200, 300 or 400 gun and cable assemblies.

SPOOL GUN AND ADAPTER KIT

(K1809-1)

The K1809-1includes the Magnum 250SG Spool gun

and the adapter kit for connecting the spool gun to the

Power MIG 215.

The Adapter Kit provides toggle switch selection

between the machineʼs use with its feeder gun or the

spool gun for same polarity welding with different wire

and gas processes.

The kit includes a spool gun adapter module assem-

bly with a single connecting plug and trigger switch, a

rear gas inlet, fitting hose, solenoid valve assembly,

and mounting hardware with installation and operation

instructions.

• Unplug or Disconnect all input power

from the POWER MIG 215 before

installing the Spool Gun and Kit.

------------------------------------------------------------------------

Wire Size Drive Roll Kit

.023”-.030” (0.6-0.8 mm)

KP1696-030S

.035” (0.9 mm) KP1696-035S

Solid

.045” (1.2 mm) KP1696-045S

Steel

.035-.045 (0.9-1.2mm) KP1696-1

.040 (1.01) KP1696-2

Cored

.035” (0.9 mm) KP1697-035C

.045” (1.2 mm) KP1697-045C

Aluminum

3/64” (1.2 mm) KP1695-3/64A

English Wire Metric Wire

Length Part No. Size Size

10' (3.0 m) K533-1

12' (3.6 m) K533-7 .035 – .045" 0.9 – 1.2 mm

15' (4.5 m) K533-3

WARNING

POWER MIG 215

MAKING A WELD WITH THE SPOOL GUN

ADAPTER KIT AND SPOOL GUN

INSTALLED

In either toggle switch position, closing either gun

trigger will cause the electrode of both guns to be

electrically “HOT”. Be sure unused gun is posi-

tioned so electrode or tip will not contact metal

case or other metal common to work.

------------------------------------------------------------------------

1. Setting spool gun selector switch to the “Normal”

position and pulling the trigger for the built-in feed-

er gun.

• Disables spool gun operation and spool gun

gas solenoid valve.

• Closing feeder gun trigger starts feeder gun

welding and makes both electrodes electrically

“HOT”.

2. Setting spool gun selector switch to the Spool Gun

Position and pulling SPOOL GUN Trigger.

• Disables built-in feeder gun operation and

machine gas solenoid valve.

• Enables spool gun operation and spool gun gas

solenoid valve.

• Closing spool gun trigger starts spool gun weld-

ing and makes both electrodes electrically

“HOT”.

3. Operation with POWER MIG 215:

• Turn the POWER MIG-215 input power ON.

• Adjusting the voltage tap control will increase or

decrease your welding voltage.

• Adjusting the wire speed control on the spool

gun will increase or decrease the spool gun

wire feed speed. NOTE: Adjusting the wire feed

speed control on the Power Mig Panel has no

affect on the spool gunʼs wire feed speed.

4. Refer to the procedure decal on the Power Mig for

initial aluminum settings. Make a test weld to deter-

mine the final settings.

5. To return to normal POWER MIG 215 welding,

release the spool gun trigger set spool gun selector

switch to normal and reset feeder gun voltage pro-

cedure setting if necessary.

C-2 C-2

ACCESSORIES

CAUTION

POWER MIG 215

La page charge ...

Lincoln Electric Welding System 215 Manuel utilisateur

Marque: Lincoln Electric

Modèle: Welding System 215

Catégorie: Système de soudage

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Lincoln Electric Welding System 215 User manual

Lincoln Electric Welding System 215 Manuel utilisateur

Ce manuel convient également à

Lincoln Electric Welding System 215 Manuel utilisateur

dans d''autres langues

Documents connexes