Amana AMAP182BW Manuel utilisateur

For questions about featur

es, operation/performance,

parts, or service, call: 1-800-207-1156.

In Canada, for assistance, installation, or service,

call: 1-800-207-1156.

Si tiene pr

eguntas respect o a las características,

funcionamiento, rendimiento, partes o servicio técnico,

llame al: 1-800-207-1156.

Au Canada, pour assistance, installation ou service,

composez le : 1-800-207-1156.

Room Air Conditioner

Use and Care Guide

Table of Contents

Table des matières

Climatiseur

Guide d’utilisation et d’entretien

AIR CONDITIONER SAFETY .......................................... 2

INSTALLATION REQUIREMENTS ................................. 3

INSTALLATION INSTRUCTIONS—

6,000-12,000 BTU MODELS ............................................ 7

WINDOW INSTALLATION INSTRUCTIONS—

15,000-24,000 BTU MODELS ........................................ 10

WALL INSTALLATION INSTRUCTIONS—

15,000-24,000 BTU MODELS ........................................ 14

USING YOUR AIR CONDITIONER ............................... 16

AIR CONDITIONER CARE ............................................ 19

TROUBLESHOOTING ...................................................20

ASSISTANCE OR SERVICE ..........................................21

XLS PRODUCTS WARRANTY FOR

AMANA

®

AIR CONDITIONERS.....................................22

SÉCURITÉ DU CLIMATISEUR

..................................... 23

EXIGENCES

D’INSTALLATION

.................................... 24

INSTRUCTIONS

D’INSTALLATION—

M

ODÈLES À 6 000 À 12 000 BTU

................................. 28

INSTALLATION

DANS UNE FENÊTRE—

MODÈLES À 15 000 À 24 000 BTU

............................... 31

INSTRUCTIONS

D’INSTALLATION AU MUR—

MODÈLES À 15,000 À 24,000 BTU

............................... 35

UTILISATION

DE VOTRE CLIMATISEUR

................... 37

ENTRETIEN

DU CLIMATISEUR

................................... 40

DÉPANNAGE .................................................................41

ASSISTANCE

OU SERVICE

.......................................... 42

GARANTIE

DE XLS PRODUCTS

POUR

LES CLIMATISEURS AMANA

®

......................... 43

Índice

Acondicionador de aire para

habitación

Manual de uso y cuidado

SEGURIDAD DEL ACONDICIONADOR DE AIRE .......44

REQUISITOS DE INSTALACIÓN ..................................45

INSTRUCCIONES DE INSTALACIÓN—

MODELOS DE 6,000-12,000 BTU ................................. 49

INSTRUCCIONES DE INSTALACIÓN PARA LA

VENTANA— MODELOS DE 15,000-24,000 BTU .........52

INSTRUCCIONES DE INSTALACIÓN PARA LA

PARED— MODELOS DE 15,000-24,000 BTU ............. 57

USO DE SU ACONDICIONADOR DE AIRE .................59

CUIDADO DEL ACONDICIONADOR DE AIRE ...........63

SOLUCIÓN DE PROBLEMAS .......................................64

AYUDA O SERVICIO TÉCNICO....................................65

GARANTÍA DE XLS PRODUCTS PARA

ACONDICIONADORES DE AIRE AMANA

®

................. 66

95114

AMAP061BW

Models/Modèles/Modelos:

®/™ ©

AMAP242BW

AMAP222BW

AMAP182BW

AMAP151BW

AMAP121BW

AMAP101BW

AMAP081BW

2

AIR CONDITIONER SAFETY

You

can be killed or seriously injured if you don't

immediately follow instructions.

You can be killed or seriously injured if you don't

follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you

what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all

safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “

DANGER” or

“WARNING.” These words mean:

IMP

ORTANT SAFETY INSTRUCTIONS

WARNING:

To reduce the risk of fire, electrical shock or injury when using your air conditioner, follow these basic precautions:

SAVE THESE INSTRUCTIONS

Unplug air conditioner before servicing.

Use two or mor

e people to move and install air conditioner.

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

This appliance is not intended for use by persons

(including children) with reduced physical, sensory,

or mental capabilities, or lack experience and knowledge,

unless they have been given supervision or instruction

concerning the use of appliance by a person responsible

for their safety.

Do not drink water collected in the water bucket.

Children should be supervised to ensure that they do not

play with the appliance.

3

INSTALLATION REQUIREMENTS

Electrical Requirements—All Models

The electrical ratings for your air conditioner are listed on the

model and serial number label. The model and serial number

label is located on the right-hand side of the air conditioner

cabinet.

Specic electrical requirements are listed in the “Electrical

Requirements” sections. Follow the requirements for the type

of plug shown in these sections.

Electrical Requirements—

115 V Models

Model BTUs − 6,000; 8,000; 10,000; 12,000; 15,000

All models −

■ 115 volts − (103.5 min. - 126.5 max.)

■ If there is a “Single Circuit Only” label on the unit, use on a

dedicated single-outlet circuit only. If a dedicated single-outlet

circuit is not available,

then it is the customer’s responsibility to have a single-outlet

circuit installed by a qualied electrician.

■ If there is no “Single Circuit Only” label on the

unit, the unit may be used on any branch circuit

of correct voltage and adequate current

protection rating.

6,000-8,000 BTU models −

■ 0-8 amps

■ 10-amp time-delay fuse or circuit breaker

10,000-15,000 BTU models −

■ 0-12 amps

■ 15-amp time-delay fuse or circuit breaker

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

Electrical Requirements—

230 V Models

Model BTUs − 18,000; 22,000; 24,000

■ 230 volts (208 min. - 240 max.)

■ 6.6-11 amps

■ 15-amp time-delay fuse or circuit breaker

■ If there is a “Single Circuit Only” label on the unit, use on a

dedicated single-outlet circuit only.

■ If a dedicated single-outlet circuit is not available, then it is

the customer’s responsibility to have a single-outlet circuit

installed by a qualied electrician.

■ If there is no “Single Circuit Only” label on the unit, the unit

may be used on any branch circuit of correct voltage and

adequate current protection rating.

Recommended Grounding Method

This air conditioner must be grounded. This air conditioner is

equipped with a power supply cord having a grounded 3 prong

plug. To minimize possible shock hazard, the cord must be

plugged into a mating, grounded 3 prong outlet, grounded in

accordance with all local codes and ordinances. If a mating

outlet is not available, it is the customer’s responsibility to have

a properly grounded 3 prong outlet installed by a qualied

electrical installer. It is the customer’s responsibility:

■ To contact a qualied electrical installer.

■ To assure that the electrical installation is adequate and in

conformance with National Electrical Code, ANSI/NFPA 70—

latest edition, and all local codes and ordinances.

Copies of the standards listed may be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02269

4

Power Supply Cord—All Models

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

NOTE: Your air conditioner’s power supply cord may differ from

those shown.

This air conditioner is equipped with a power supply cord

required by UL. This power supply cord contains state-of-the-art

electronics that sense leakage current. If the cord is crushed,

the electronics detect leakage current and power will be

disconnected in a fraction of a second.

To test your power supply cord:

1. Plug power supply cord into a grounded 3 prong outlet.

2. Press RESET (on some models, a green light will turn on).

3. Press TEST (listen for click; Reset button will trip, and on

some devices, a green light will turn off).

4. Press and release RESET (listen for click; Reset button will

latch, and on some devices, a green light will turn on).

The power supply cord is ready for operation.

NOTES:

■ The Reset button must be pushed in for proper operation.

■ The power supply cord must be replaced if it fails to trip when

the test button is pressed or fails to reset.

■ Do not use the power supply cord as an off/on switch. The

power supply cord is designed as a protective device.

■ A damaged power supply cord must be replaced with a new

power supply cord obtained from the product manufacturer

and must not be repaired.

■ The power supply cord contains no user-serviceable parts.

Opening the tamper-resistant case voids all warranty and

performance claims.

Tools Required—All Models

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Phillips screwdriver

Tape measure

Scissors

Cordless drill and

1/8" bit

Level

Pencil

Flathead screwdriver Adjustable wrench

or pliers

Socket wrenches

Parts Supplied:

6,000-12,000 BTU models

Check that all parts are included in parts package.

NOTE: Not all parts are included with all models.

A. Foam seal with

adhesive strip

B. Foam seal without

adhesive strip

C. Sash lock x1

D. Lock frame x2

E. 1/2" screws x3

F. 3/4" screws x4

G. Side curtains x2

H. 3/8" screws x4

I. Top channel (appearance

may vary)

Other: AAA batteries x2

A

B

C

D

E

G

H

Left

Right

I

F

5

Parts Supplied—

15,000-24,000 BTU Models

Check that all parts are included in parts package.

NOTE: Not all parts are included with all models.

A. Foam seal with

adhesive strip

B. Foam seal without

adhesive strip

C. Side curtain bracket x2

D. Safety lock

E. Sill angle bracket x2

F. 1/2" hex-head screw x2

G. 5/8" hex-head screw x4

H. 5/16" hex-head screw x10

I. 5/8" athead bolt with

locknut x2

J. 1/2" athead bolt with

locknut x4

K. Gasket x2

L. Top channel (appearance

may vary)

M. Window support

bracket x2

N. Side curtains x2

O. Side retainers x2

Other: AAA batteries x2

Model BTUs Width (A) Minimum

Opening (B)

6,000-8,000

23"−36"

(58.4 cm−91.4 cm)

14

1

⁄2"

(36.8 cm)

10,000-12,000

26"−36"

(66 cm−91.4 cm)

16"

(40.6 cm)

15,000-18,000 28"−41"

(71.1 cm−104.2 cm)

19"

(48.3 cm)

22,000-24,000

30"−41"

(76.2 cm−104.2 cm)

19

1

⁄2"

(49.5 cm)

Window Opening Measurements

A

B

Location Requirements—

Window Installation

IMPORTANT: Observe all governing codes and ordinances.

Check the location where the air conditioner will be installed.

Make sure you have everything necessary for correct installation.

The location should provide:

■ Grounded electrical outlet within 6 ft (183 cm) of where

the power cord exits the air conditioner. Do not use an

extension cord.

■ Free movement of air in room to be cooled.

■ A large enough opening for the air conditioner. Installation

parts are supplied for double-hung windows.

NOTE: The air conditioner can be installed without the side

panels to t in a narrow window opening.

■ Adequate wall support for weight of air conditioner.

■ Firm wood, masonry, or metal to secure to supporting parts.

NOTE: Cabinet louvers must not be obstructed. Air must be able

to pass freely through the cabinet louvers.

A

B

C

D E

F

G

H

I

K

L

M

N

O

J

Left

Right

6

Preparing Window with Storm Window

or Other Obstruction

Follow the steps in “Prepare Window Opening”.

If possible, remove the storm window frame or other obstruction.

If the storm window frame or obstruction CANNOT be removed,

a wood spacer will be required to ensure that the air conditioner

slopes to the outside. This will allow condensation and rainwater

to drain away. Make sure that drain holes or slots are not caulked

or painted shut.

Using a level and measuring tape, determine thickness of wood

spacer needed to allow the air conditioner to slope downward

slightly to the outdoors. The block should provide at least 1/2"

(1.27 cm) of height above the obstruction.

1

/2"

Min.

1

/2"

Min.

1. Measure size of spacer needed

Spacer

Obstruction

Place wood spacer on windowsill. Spacer should be at least the

full width of the air conditioner cabinet.

A

B

C

1

/2"

Min.

1

/2"

Min.

E

D

2. Place block on windowsill

A. Piece of wood

B. Windowsill

C Indoors

D. Outdoors

E. Storm window frame

or other obstruction

Prepare Window Opening

Measure the width of the window opening (A). Mark the center

line (B) of the window on the inside windowsill.

A

B

1. Measure and mark center line

Attach the foam seal with adhesive strip to the bottom of the

window sash.

2. Attach upper foam seal

Foam seal

Center line

Width of window opening

1

(3.8 cm)

(1.27 cm)

1

(3.8 cm)

(1.27 cm)

7

INSTALLATION INSTRUCTIONS—6,00012,000 BTU MODELS

1. Unpack the Air Conditioner

Remove Packaging Materials:

■ Handle the air conditioner gently while unpacking the unit.

■ Place the air conditioner on a hard, at surface.

■ Remove tape and glue residue from surfaces before turning

on the air conditioner. Rub a small amount of liquid dish soap

over the adhesive with your ngers. Wipe with a damp cloth

and dry.

■ Do not use sharp instruments, rubbing alcohol, ammable

uids, or abrasive cleaners to remove tape or glue. These

products can damage the surface of your air conditioner.

■ Remove any packaging materials inserted into the side

louvers.

■ Dispose of/recycle packaging materials in an appropriate way.

Prepare Air Conditioner for Installation

WARNING

Excessive Weight Hazard

Use two or more people to move and install

air conditioner.

Failure to do so can result in back or other injury.

Using four 3/8" screws, attach the top channel to the air

conditioner.

3. Attach screws

Place the top channel on the top of the air conditioner, lining up

the holes in the top channel with the holes in the top of the air

conditioner.

2. Install top channel

8

Slide the side curtain frame into the top channel and bottom

channels of the air conditioner. Make slight adjustments until

the panel sits securely inside the channels.

Repeat steps 1 and 2 for other side curtain and frame.

2. Insert curtain frame into channels

A

B

C

2. Lower window sash into place

Lower the window sash behind the top channel to hold the air

conditioner in place.

NOTE: Your model may differ from the one shown.

A. Side curtain

against window

channel

B. Window sash

behind top

channel

C. Bottom channel

behind window

sill

A

B

C

D

1. Position air conditioner in window

Using two or more people, place the air conditioner into the

window opening so the bottom of the air conditioner frame is

against the window sill. Tilt the back of the unit slightly downward

to allow accumulated rain water to drain out.

A. Air conditioner

B. Bottom channel

C Windowsill

D. Outside

Holding the center of the right-hand side panel in one hand, pull

the curtain open. Place the tabbed side of the side curtain in the

track on the right-hand side of the air conditioner cabinet.

Slide the side curtain down the track, making sure to leave

enough space to slip the top and bottom of the frame into the

channels on the cabinet.

Install Side Curtains

NOTE: Attach curtains to the air conditioner before placing

the air conditioner in window.

1. Install side curtain

Right curtain frame

Tabbed side of curtain

IMPORTANT:

■ Be sure your air conditioner does not fall out of the opening

during installation or removal.

■ The place where the power cord exits the air conditioner

should be no more than 6 ft (183 cm) from a grounded outlet

■ To maximize cooling efciency and air circulation, do not

block the air intake or discharge louvers in the front panel.

■ To reduce cycling on and off of the compressor and reduce

the risk of freezing up or damage to the unit, do not block the

louvers on the outside of the air conditioner.

Install Air Conditioner in Window

WARNING

Excessive Weight Hazard

Use two or more people to move and install

air conditioner.

Failure to do so can result in back or other injury.

9

3. Extend side curtains

Extend side curtains out until they t into the window channels.

5. Install screws into window sash

Use a 1/8" drill bit to drill a starter hole through the holes in the

top rail and the top corners of the side curtains into the window

sash.

Secure with three 1/2" screws through the holes in the top rail

and side curtain and into the window sash.

A

B

7. Install foam seal

A. Top of lower

window sash

B. Foam seal

Insert the foam seal without adhesive strip between the top of the

lower window sash and the glass of the upper window.

Remove any remaining clear plastic lm from the control panel

and plastic front panel.

4. Install side curtain brackets

Slide a side bracket over the bottom corner of each side curtain

frame.

Using a 1/8" drill bit, drill a starter hole through the hole in the

side curtain bracket and into the windowsill.

Secure each bracket to the windowsill with a 3/4" screw.

6. Secure lower sash

Attach the right angle sash lock with a 3/4" screw.

10

Pull down the front panel and remove the lter. Lift the front panel

upwards and remove from the air conditioner. Place to the side.

2. Remove lter and front panel

Remove the four faceplate screws.

NOTE: The faceplate screws must be reinstalled before mounting

the air conditioner.

3. Remove faceplate screws

Gently remove the faceplate from the air conditioner cabinet.

4. Remove faceplate

1. Unpack the Air Conditioner

Remove Packaging Materials:

■ Handle the air conditioner gently while unpacking the unit.

■ Place the air conditioner on a hard, at surface.

■ Remove tape and glue residue from surfaces before turning

on the air conditioner. Rub a small amount of liquid dish soap

over the adhesive with your ngers. Wipe with a damp cloth

and dry.

■ Do not use sharp instruments, rubbing alcohol, ammable

uids, or abrasive cleaners to remove tape or glue. These

products can damage the surface of your air conditioner.

■ Remove any packaging materials inserted into the side

louvers.

■ Dispose of/recycle packaging materials in an appropriate way.

Prepare Air Conditioner for Installation

WARNING

Excessive Weight Hazard

Use two or more people to move and install

air conditioner.

Failure to do so can result in back or other injury.

WINDOW INSTALLATION INSTRUCTIONS—

15,000-24,000 BTU MODELS

Remove the control panel screw from the front panel.

5. Remove control panel screw

11

3. Slide in side panels

Slide the “I” section of the window panel into the side bracket

f the cabinet. Do this for both sides.

Remove the screws from the right side of the cabinet.

6. Remove right-side screws

IMPORTANT: To avoid damage, do not pull or lift near the top

of the unit.

Hold the cabinet while pulling on the base handle to carefully

remove the unit.

7. Remove chassis

4. Attach side panels

Insert the top and bottom legs of the window ller panel frame

into the top angle channel and bottom channel. Secure with

5/16" screws. Repeat on the other side and install side retainer

into cabinet.

5/16"

screws

Install Top Channel and Side Bracket

2. Install top angle channel

Attach the top angle channel to the cabinet with four 5/16"

hex-head screws.

Place air conditioner on a hard, at surface. Attach the foam

gasket to the top angle channel.

1. Attach foam gasket

Install Air Conditioner in Window

IMPORTANT:

■ Be sure your air conditioner does not fall out of the opening

during installation or removal.

■ The place where the power cord exits the air conditioner

should be no more than 6 ft (183 cm) from a grounded outlet.

■ To maximize cooling efciency and air circulation, do not

block the air intake or discharge louvers in the front panel.

■ To reduce cycling on and off of the compressor and reduce

the risk of freezing up or damage to the unit, do not block the

louvers on the outside of the air conditioner.

WARNING

Excessive Weight Hazard

Use two or more people to move and install

air conditioner.

Failure to do so can result in back or other injury.

12

NOTE: If necessary, pre-drill holes in windowsill.

Fasten the cabinet to the windowsill using two 5/8" round-head

screws. Add the bottom channel seal over the screws. For 22,000

and 24,000 BTU models, the bottom channel seal should sit on a

gasket.

3. Secure cabinet

2. Close window

Make sure the bottom channel is seated over the window sill as

shown. Bring the window down temporarily behind the top angle

channel to hold the cabinet in place. Tilt the back of the unit

slightly downward to allow accumulated rain water to drain out.

Hold each support bracket ush against the outside of the

window sill. Tighten each bracket to the bottom of the cabinet.

Mark the location of the brackets at the top level of the

windowsill. Remove the brackets.

Install Support Brackets

NOTE: Attach curtains to the air conditioner before placing the air

conditioner in window.

1. Mark bracket location

Attach the sill angle brackets to the support brackets with 1/2"

screws, at head bolts, and locknuts as shown. Hand tighten

screws loosely to accommodate changes that may be required

later in installation.

2. Assemble brackets

Sill

Stool

angle

1/2" screw

1/2"

locknuts

5/8" athead

bolt

Sill angle

bracket

5/8" locknuts

1. Position air conditioner in window

Using two or more people, place the air conditioner into the

window opening so the bottom of the air conditioner frame is

against the window sill.

A. Air conditioner

B. Side panel

C. Plastic frame

D. “I” section

E. Locking screw hole

A

B

C

D

E

Attach the support brackets (with sill angle brackets attached)

to the bottom of the cabinet with 1/2" screws and locknuts as

shown. Tighten all six bolts securely.

3. Attach assembled brackets

13

Extend Side Panels

Raise the window to expose the window side panel and panel

frame. Loosen the locking screws so the side panels slide easily.

1. Loosen locking screws

Attach the right angle safety lock with a 5/8" hex-head screw.

2. Attach right angle safety lock

Extend each panel to completely ll the width of the

window. Tighten the locking screws when the panels are

fully extended.

2. Extend window panels

Install the Chassis into the Cabinet

WARNING

Excessive Weight Hazard

Use two or more people to move and install

air conditioner.

Failure to do so can result in back or other injury.

IMPORTANT: To prevent damage to the unit, do not push on

the controls or nned coils.

Using two people, lift the air conditioner chassis and carefully

slide it into the cabinet. Let the front of the air conditioner

hang out approximately 6" (15.24 cm). Be sure the chassis is

rmly seated in the back of the cabinet.

1. Reinsert air conditioner chassis

Insert all screws removed during window installation.

Reattach the front faceplate, front panel, and air lter. Refer

to the “Prepare Air Conditioner for Installation” section for

more information.

2. Reassemble air conditioner

Install Window Lock and Sash Seal

NOTE: Attach curtains to the air conditioner before placing the air

conditioner in window.

Trim the sash seal to t the width of the window. Insert the sash

seal into the space between the upper and lower sashes.

1. Insert sash seal

1/2"

screws

5/8"

screw

14

WALL INSTALLATION INSTRUCTIONS—

15,00024,000 BTU MODELS

Additional Tools Required

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools

listed here.

■ Wood frame

■ Shims

■ 10 wood screws − 1" (2.54 cm) long minimum

Selecting a Wall Installation Site

The air conditioner has a slide-out chassis so that it can be

installed through an outside wall.

Max wall thickness: 8" (20.32 cm)

IMPORTANT: In order to ensure proper airow, the side louvers

must never be blocked.

Wall requirements:

■ Allows unblocked airflow from the rear and sides of the air

conditioner

■ Located near existing electrical outlets or where another

outlet can or will be installed

■ Does not support major structural loads, such as the frame

construction at ends of windows, under truss-bearing

points, etc.

■ Does not have plumbing or wiring inside

■ Does not have objects blocking the air vents

Preparing the Wall Installation Site

The air conditioner has a slide-out chassis, so that it can be

installed through an outside wall. Prepare the wall in-frame

construction (including brick and stucco veneer).

Working from inside the room, nd the wall stud that is nearest to

the center of the installation area. Cut a hole on each side of the

center stud, leaving at least 3

3

/" (8.57 cm) below the hole.

1. Cut a hole on sides of center stud

3

/"

minimum

Using the below table to nd installation dimensions, measure

between the inside edges of every other stud.

Width X=inside model plus twice the thickness of the framing

material used.

Height Y= inside model height plus twice the thickness of the

framing material used.

15K/18K models 22K/24K models

Inside-frame

height

18¼" (46.4 cm) 19/" (49.5 cm)

Inside-frame

width

23/" (60.6 cm) 26

9

/" (68.3 cm)

Y

X

Build a wooden frame with the inside dimensions of your model

listed above. The frame depth should be the same as the wall

thickness. Fill in extra space from the opening to the studs with

wood spacers as shown.

Nail the spacers to the studs. They should be ush with the

drywall.

2. Build frame

15

NOTE: If the wall thickness is 8½" (21.59 cm) or more, add

aluminum flashing over the bottom of the frame opening to

assure water is unable to enter the area between the inner

and outer wall.

Prepare and Install the Cabinet

Place the cabinet into the opening with the bottom channel

resting rmly on the bottom rail of the wood frame. Position

the cabinet so it is properly tilted for water removal.

2. Place and position cabinet

Assemble brackets. See “Install Support Brackets” in the

“Window Installation” section. Nail a wooden strip to the

outside wall to be used in conjunction with the angled sill

support brackets.

4. Place and position cabinet

Screw or nail the cabinet to the wooden frame using shims if

the frame is oversized to eliminate possible noise. Remember

to maintain proper slope for water elimination.

Reinstall the chassis into the cabinet. See the “Install the Chassis

into the Cabinet” section.

5. Secure cabinet and install chassis

Masonry Construction

1. Cut or build a wall opening in the masonry wall similar to the

frame contruction. See the “Wall Installation Instructions –

240 V Models” section for a wall thickness greater than 8½"

(21.59 cm).

2. Secure the cabinet in place using masonry nails or masonry

anchor screws. Or build a frame using the instructions found

in the “Wall Installation Instructions – 240 V Models” section.

3. Make sure the masonry above the cabinet is supported well.

Use the existing holes in the cabinet or additional drilled holes

to fasten the cabinet at various positions. Make sure that the

side louvers are clear of any obstructions.

4. Install the exterior cabinet support brackets according to

“Prepare and Install the Cabinet” in the “Wall Installation

Instructions – 240 V Models” section. Caulk or ash with

aluminum if needed. This will provide a tight seal around

the top and sides of the cabinet.

5. For a more aesthetically pleasing installation, apply wood trim

molding around the sides of the cabinet without obstructing

the side louvers.

Secure the bottom channel to the wood frame with two large

1" (2.5 cm) wood screws.

3. Secure bottom channel to frame

Slide the chassis from the cabinet. See the “Prepare Air

Conditioner for Installation” section for more details.

1. Remove chassis

Aluminum

ashing

Caulk as

needed

Gap size 5/16"

to 3/8"

Support

bracket

Wooden

strip

16

Operating your air conditioner properly helps you to obtain the

best possible results.

This section explains proper air conditioner operation.

IMPORTANT:

■ If you turn off the air conditioner, wait at least 3 minutes

before turning it back on. This prevents the air conditioner

from blowing a fuse or tripping a circuit breaker.

■ Do not try to operate your air conditioner in the Cool mode

when outside temperature is below 65°F (18°C). The inside

evaporator coil will freeze up, and the air conditioner will not

operate properly.

NOTE: In the event of a power failure, your air conditioner will

operate at the previous settings when the power is restored.

Turning on the Air Conditioner

1. Press POWER to turn on air conditioner.

2. Press POWER again to turn off the air

conditioner.

Selecting the Mode

1. Press MODE to cycle through modes.

2. Choose Cool, Dry, or Fan.

■ Cool—Cools the room and reduces air

humidity. Press MODE to activate the cooling

function. Press the up or down arrow button

to adjust the temperature.

■ Dry Mode—Reduces the humidity of the air.

Press MODE to set the Dry mode. An automatic

function of alternating cooling cycles and air fan is

activated.

■ Fan—Only the fan runs. Press MODE to set the

Fan mode. Press FAN SPEED to select High, Med,

and Low. The remote control stores the speed set

in the previous mode of operation. In Auto mode,

the unit automatically chooses the fan speed and the mode of

operation (Cool, Dry, or Fan).

NOTE: After 5 seconds, display will show the current room

temperature.

USING YOUR AIR CONDITIONER

Features

■ Eco—Conserves energy by turning off

compressor when room reaches desired

temperature. The fan motor will run for 10

minutes, stop for 20 seconds, then run again.

The compressor will turn back on when the room

temperature rises above the set temperature.

Press ECO to turn Eco feature on and off. When

the unit is in Eco mode, the light will turn on.

■ Sleep—Automatically adjusts the temperature

and fan speed to make the room more

comfortable during the night. Press and hold

the SLEEP button for 10 seconds until the sleep light turns

on. All of the left lights will turn off. The set temperature

will automatically raise by 1.8°F (1°C) every 30-60 minutes.

At most, the temperature will change six times until the

temperature reaches 82°F (28°C). Running time depends upon

the set temperature.

NOTE: After 5 seconds, display will show the current room

temperature.

Selecting the Fan Speed

1. Press FAN until the LED indicator for the desired setting is lit.

2. Choose Low, Med, or High.

■ Low—Low fan speed

■ Med—Normal fan speed

■ High—Maximum fan speed

NOTES:

■ Auto fan speed and temperature cannot be selected in Fan

Only mode.

■ In Eco and Sleep modes, Auto fan speed is selected

automatically.

■ After 5 seconds, the display will show the current room

temperature.

Adjusting the Temperature

Press the up arrow button to increase the

set temperature.

Press the down arrow button to decrease

the set temperature.

NOTE: After 5 seconds, the display on the

air conditioner control panel will show the

current room temperature.

MODESPEED

MODE

SPEED

MODESPEED

MODE

SPEED

MODESPEED

17

Using the Timer

Delayed Shutoff:

Use the timer to set the air conditioner to turn off automatically

after a 0.5- to 24-hour delay (the air conditioner must be on):

1. Press TIMER. The display will show remaining

time before the air conditioner will turn off.

2. Press the up or down arrow button to change

the delayed shut-off time from 0.5 to 24 hours.

The time can be set in 0.5-hour increments below 10 hours

and 1-hour increments for 10 hours or above.

3. Press TIMER again to conrm setting.

NOTE: The Set light will turn on while setting.

Delayed Start:

You can also set the air conditioner to turn on automatically after

a 0.5- to 24-hour delay.

NOTE: After the set delay, the air conditioner will turn on with

the previous settings. Change the mode, fan speed, and/or

temperature before setting the timer, if desired.

1. Turn off the air conditioner.

2. Press TIMER. Set the temperature by pressing the up or down

arrow button.

3. Press TIMER a second time to set the rest time. Press the up

or down arrow button to change the delay time from 0.5 to 24

hours, then press TIMER again.

4. Press TIMER again while the time remaining is shown on the

display.

To Cancel Timer:

After the timer has been set, press TIMER.

Changing Air Direction

Use tab to adjust air direction

Normal Operating Sounds

When your air conditioner is operating normally, you may hear

sounds such as:

■ Droplets of water hitting the condenser, causing a pinging or

clicking sound. The water droplets help cool the condenser.

■ Air movement from the fan.

■ Clicks from the thermostat cycle.

■ Vibrations or noise due to poor wall or window construction.

■ A high-pitched hum or pulsating noise caused by the modern

high-efciency compressor cycling on and off.

■ Water will collect in the base pan during rain or days of high

humidity. The water may overow and drip from the outside

part of the unit.

Use the thumb wheel on the vent louvers to adjust the air

direction left or right.

MODESPEED

Clean Filter Reminder

To help maximize energy efciency, this air

conditioner features a Clear Filter reminder.

After 500 hours of operation, FILTER will

illuminate as a reminder that it is time to

clean the lter. Once the light is illuminated, it can be turned off

by pressing the FILTER button. See the “Air Conditioner Care”

section for instructions on how to clean the lter.

MODESPEED

18

Using the Remote Control

Power

1. Press POWER to turn on air conditioner.

2. Press POWER again to turn off the air conditioner.

Cool

Press COOL to enter Cool mode.

Fan Speed

1. Press FAN SPEED until you see the bar LED on the air

conditioner control panel display for the desired setting.

2. Choose Low, Medium, or High.

NOTES:

■ Auto fan speed and Temperature cannot be selected in Fan

mode.

■ In Energy Saver (on some models) and Cool modes, Auto fan

speed is selected automatically.

Adjusting Temperature

Press the up arrow button to increase the set

temperature. Press the down button to decrease

the set temperature.

NOTE: After 5 seconds, the display on the air

conditioner control panel will show the current

room temperature.

POWER COOL

SLEEP

TIMER

ECO

DISPLAY

AUTO

MODE

FAN

ONLY

FAN

SPEED

Timer

Delayed Shutoff:

Use the timer to set the air conditioner to turn off automatically

after a 0.5- to 24-hour delay (the air conditioner must be on):

1. Press TIMER. The display will show remaining time

before the air conditioner will turn off.

2. Press the up or down arrow button to change the

delayed shut-off time from 0.5 to 24 hours. The time

can be set in 0.5-hour increments below 10 hours and 1-hour

increments for 10 hours or above.

3. Press TIMER again to conrm setting.

NOTE: The Set light will turn on while setting.

Delayed Start:

You can also set the air conditioner to turn on automatically after

a 0.5- to 24-hour delay.

NOTE: After the set delay, the air conditioner will turn on with

the previous settings. Change the mode, fan speed, and/or

temperature before setting the timer, if desired.

1. Turn off the air conditioner.

2. Press TIMER. Set the temperature by pressing the up or down

arrow button.

3. Press TIMER a second time to set the rest time. Press the up

or down arrow button to change the delay time from 0.5 to 24

hours, then press TIMER again.

4. Press TIMER again while the time remaining is shown on the

display.

To Cancel Timer:

After the timer has been set, press TIMER.

POWER COOL

SLEEP

TIMER

ECO

DISPLAY

AUTO

MODE

FAN

ONLY

FAN

SPEED

Eco

■ Conserves energy by turning off compressor when

room reaches desired temperature. The fan motor

will run for 10 minutes, stop for 20 seconds, then

run again. The compressor will turn back on when

the room temperature rises above the set temperature. Press

ECO to turn Eco feature on and off. When the unit is in Eco

mode, the light will turn on.

Sleep

Automatically adjusts the temperature and fan speed

to make the room more comfortable during the night.

Press and hold the SLEEP button for 10 seconds until

the Sleep light turns on. All of the left lights will turn off. The set

temperature will automatically raise by 1.8°F (1˚C) every 30-60

minutes. At most, the temperature will change six times until the

temperature reaches 82°F (28°C). Running time depends upon

the set temperature.

POWER COOL

SLEEP

TIMER

ECO

DISPLAY

AUTO

MODE

FAN

ONLY

FAN

SPEED

POWER COOL

SLEEP

TIMER

ECO

DISPLAY

AUTO

MODE

FAN

ONLY

FAN

SPEED

Auto:

Press AUTO MODE to enter into Auto mode. In this mode,

the fan speed and temperature are set automatically

according to the room temperature as tested by the indoor

temperature sensor.

Display:

Press DISPLAY to switch on/off all lights or the LED

display.

Fan only:

Press the Fan Only button to enter Fan Only mode.

POWER

COOL

SLEEP

TIMER

ECO

DISPLAY

AUTO

MODE

FAN

ONLY

FAN

SPEED

POWER

COOL

SLEEP

TIMER

ECO

DISPLAY

AUTO

MODE

FAN

ONLY

FAN

SPEED

POWER COOL

SLEEP

TIMER

ECO

DISPLAY

AUTO

MODE

FAN

ONLY

FAN

SPEED

POWER COOL

SLEEP

TIMER

ECO

DISPLAY

AUTO

MODE

FAN

ONLY

FAN

SPEED

POWER COOL

SLEEP

TIMER

ECO

DISPLAY

AUTO

MODE

FAN

ONLY

FAN

SPEED

POWER COOL

SLEEP

TIMER

ECO

DISPLAY

AUTO

MODE

FAN

ONLY

FAN

SPEED

POWER COOL

SLEEP

TIMER

ECO

DISPLAY

AUTO

MODE

FAN

ONLY

FAN

SPEED

Replacing the battery

Use a small Phillips screwdriver to loosen the battery cover

screw. Slide the battery cover down with two thumbs to remove.

Remove and properly dispose of old batteries, then replace with

two new AAA batteries. Replace the battery cover and tighten the

screw.

Remove and replace batteries

19

Your new air conditioner is designed to give you many years of

dependable service. This section tells you how to clean and care

for your air conditioner properly.

Remove the lter from the grille by lifting to release the slotted

tabs on the top and bottom of the grille.

Reinstalling the air filter:

1. Reattach the air lter to the air intake grille.

2. Insert the air intake grille into the slots on the air conditioner

and snap into place.

Remove the lter by grasping the tab on the lter and pulling it

out of the grille to the side.

Reinstalling the air filter:

1. Slide the lter back into the grille.

AIR CONDITIONER CARE

1. Removing the intake grille

Turn off the air conditioner.

Remove the air lter by pressing down on the tabs on the air

intake grille and pulling the grille away from the air conditioner.

2. Removing the air lter

Air Filter Removal—Top Insert

On some models, the air lter is located behind the intake grille

of air conditioner.

Cleaning the Air Filter

The air lter is removable for easy cleaning. A clean lter helps

remove dust, lint, and other particles from the air and is important

for best cooling and operating efciency. Check the lter at least

once per month to see whether it needs cleaning.

NOTE: Do not operate the air conditioner without the lter in

place. Doing so will degrade the unit performance over time.

Use a vacuum cleaner to clean air lter. If the air lter is very dirty,

wash it in warm water with a mild detergent.

NOTE: Do not wash the air lter in the dishwasher or use any

chemical cleaners; it may damage the lter. Air dry the air lter

completely before replacing to ensure maximum efciency.

Cleaning the Front Panel

1. Unplug the air conditioner to prevent shock or a re hazard.

2. Wipe the front panel with a soft, damp cloth.

3. Air dry the front panel completely.

Repairing Paint Damage

Check once or twice a year for paint damage. This is very

important, especially in areas near saltwater or where rust is a

problem. If needed, touch up with a good grade enamel paint.

Winter Storage

1. Remove the air conditioner according to the installation

instructions.

2. Cover the air conditioner with plastic or place it back into the

original box.

1. Removing the air lter

Air Filter Removal—Side Insert

On some models, the air lter slides out the side of the intake

grille.

20

TROUBLESHOOTING

Before calling for service, try the suggestions below to see whether you can solve your problem without outside help.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

PROBLEM POSSIBLE CAUSES RECOMMENDED SOLUTIONS

The Air Conditioner Will

Not Start

The air conditioner is unplugged. Make sure the power supply cord is plugged into a

grounded 3 prong outlet.

The fuse is blown/circuit breaker is tripped. Check the house fuse/circuit breaker box and replace

the fuse or reset the breaker.

Power failure The unit will automatically restart when power is

restored. There is a protective time delay (approximately

3 minutes) to prevent tripping of the compressor

overload. The unit may not start normal cooling for

3 minutes after it is turned back on.

The power cord reset button is tripped. Press the reset button located on the power cord plug.

If the reset button will not stay engaged, discontinue

use of the air conditioner and contact a qualiﬁed service

technician.

The Air Conditioner Is

Not Cooling Properly

Airﬂow is restricted. Make sure there are no curtains, blinds, or furniture

blocking the front of the air conditioner.

The temperature control is not set correctly. Lower the set thermostat temperature.

The air ﬁlter is dirty. Clean the ﬁlter. See the “Air Conditioner Care” section.

The room is too warm. Allow time for the room to cool down after turning on the

air conditioner.

Cold air is escaping. Close all open doors and/or windows where warm air

may be entering.

The cooling coils are frozen. See “The Air Conditioner Is Freezing Up” below.

The Air Conditioner Is

Freezing Up

Ice is blocking the airﬂow. Turn off the unit and allow it to thaw until the ice has

melted, then operate on a higher fan speed. If this

continues to occur, contact customer service for

additional help.

The Remote Control Is

Not Working

Batteries are inserted incorrectly. Check that the batteries are inserted in the correct

direction.

Batteries are dead. Replace the batteries and dispose of them in a

responsible manner.

La page charge ...

Amana AMAP182BW Manuel utilisateur

Amana AMAP182BW Manuel utilisateur

dans d''autres langues

Autres documents