Hotpoint I55RM 1110 W 1 Mode d'emploi

Instructions for use

EN

DE

Gebrauchsanweisung

FR

Mode d’emploi

NL

Gebruiksaanwijzing

ENGLISH Instructions for use Page 4

DEUTSCH Gebrauchsanweisung Seite 22

FRANÇAIS Mode d’emploi Page 40

NEDERLANDS Gebruiksaanwijzing Pagina 58

4

SAFETY INSTRUCTIONS

IMPORTANT to be read and observed

Before using the appliance, read

these safety instructions. Keep them

nearby for future reference.

These instructions and the appliance

itself provide important safety

warnings, to be observed at all times.

The manufacturer declines any

liability for failure to observe these

safety instructions, for inappropriate

use of the appliance or incorrect

setting of controls.

Very young children (0-3 years)

should be kept away from the

appliance. Young children (3-8

years) should be kept away from

the appliance unless continuously

supervised. Children from 8 years

old and above and persons with

reduced physical, sensory or mental

capabilities or lack of experience and

knowledge can use this appliance

only if they are supervised or have

been given instructions on safe

use and understand the hazards

involved.

Children must not play with the

appliance. Cleaning and user

maintenance must not be carried out

by children without supervision.

PERMITTED USE

CAUTION: The appliance is not

intended to be operated by means

of an external switching device,

such as a timer, or separate remote

controlled system.

This appliance is intended to

be used in household and similar

applications such as: staff kitchen

areas in shops, ofces and other

working environments; farm houses;

by clients in hotels, motels, bed

& breakfast and other residential

environments.

This appliance is not for

professional use. Do not use the

appliance outdoors.

The bulb used inside the

appliance is specically designed

for domestic appliances and is not

suitable for general room lighting

within the home (EC Regulation

244/2009).

The appliance is designed for

operation in places where the

ambient temperature comes within

the following ranges, according to

the climatic class given on the rating

plate. The appliance may not work

properly if it is left for a long time at

a temperature outside the specied

range.

Climatic Class Amb. T. (°C)

SN: From 10 to 32 °C

ST: From 16 to 38 °C;

N: From 16 to 32 °C

T: From 16 to 43 °C

This appliance does not

contain CFCs. The refrigerant

circuit contains R600a (HC).

Appliances with Isobutane

(R600a): isobutane is a natural

gas without environmental

impact, but is ammable.

Therefore, make sure the

refrigerant circuit pipes are

not damaged, especially when

emptying the refrigerant circuit.

WARNING: Do not damage the

appliance refrigerant circuit pipes.

WARNING: Keep ventilation

openings, in the appliance enclosure

or in the built-in structure, clear of

obstruction.

5

WARNING: Do not use

mechanical, electric or chemical

means other than those

recommended by the Manufacturer

to speed up the defrost process.

WARNING: Do not use or

place electrical devices inside the

appliance compartments if they are

not of the type expressly authorised

by the Manufacturer.

WARNING: Ice makers and/

or water dispensers not directly

connected to the water supply must

be lled with potable water only.

Do not store explosive substances

such as aerosol cans and do not

place or use gasoline or other

ammable materials in or near the

appliance.

Do not swallow the contents (non-

toxic) of the ice packs (provided with

some models). Do not eat ice cubes

or ice lollies immediately after taking

them out of the freezer since they

may cause cold burns.

For products designed to use

an air lter inside an accessible fan

cover, the lter must always be in

position when the refrigerator is in

function.

Do not store glass containers with

liquids in the freezer compartment

since they may break.

Do not obstruct the fan (if included)

with food items.

After placing the food check that the

door of the compartments closes

properly, especially the freezer door.

Damaged gaskets must be

replaced as soon as possible.

Use the refrigerator compartment

only for storing fresh food and the

freezer compartment only for storing

frozen food, freezing fresh food and

making ice cubes.

Avoid storing unwrapped food

in direct contact with internal

surfaces of the refrigerator or freezer

compartments.

Appliances could have special

compartments (Fresh Food

Compartment, Zero Degree Box,...).

Unless differently specied in the

specic booklet of product, they can

be removed, maintaining equivalent

performances.

C-Pentane is used as blowing

agent in the insulation foam

and it is a ammable gas.

INSTALLATION

The appliance must be handled

and installed by two or more persons

- risk of injury. Use protective gloves

to unpack and install - risk of cuts.

Installation, including water supply

(if any), electrical connections and

repairs must be carried out by a

qualied technician. Do not repair

or replace any part of the appliance

unless specically stated in the user

manual. Keep children away from

the installation site. After unpacking

the appliance, make sure that it has

not been damaged during transport.

In the event of problems, contact

the dealer or your nearest Aftersales

Service. Once installed, packaging

waste (plastic, styrofoam parts

etc.) must be stored out of reach of

children - risk of suffocation. The

appliance must be disconnected

from the power supply before any

installation operation - risk of electric

shock. During installation, make sure

the appliance does not damage the

power cable - risk of re or electric

shock. Only activate the appliance

6

when the installation has been

completed.

Be careful not to damage the

oors (e.g. parquet) when moving the

appliance. Install the appliance on

a oor or support strong enough to

take its weight and in a place suitable

for its size and use. Make sure the

appliance is not near a heat source

and that the four feet are stable and

resting on the oor, adjusting them

as required, and check that the

appliance is perfectly level using a

spirit level. Wait at least two hours

before switching the appliance on, to

ensure that the refrigerant circuit is

fully efcient.

All dimensions and spacing needed

for installation of the appliance are in

the Installation Instruction booklet.

WARNING: When positioning the

appliance, ensure the supply cord is

not trapped or damaged.

WARNING: To avoid a hazard

due to instability, positioning or xing

of the appliance must be done in

accordance with the manufacturer

instructions.

It’s forbidden to place the refrigerator

in such way that the metal hose of

gas stove, metal gas or water pipes,

or electrical wires are in contact with

the refrigerator back wall (condenser

coil).

ELECTRICAL WARNINGS

It must be possible to disconnect

the appliance from the power

supply by unplugging it if plug is

accessible, or by a multi-pole switch

installed upstream of the socket in

accordance with the wiring rules

and the appliance must be earthed

in conformity with national electrical

safety standards.

Do not use extension leads,

multiple sockets or adapters. The

electrical components must not

be accessible to the user after

installation. Do not use the appliance

when you are wet or barefoot.

Do not operate this appliance if it has

a damaged power cable or plug, if

it is not working properly, or if it has

been damaged or dropped.

If the supply cord is damaged, it

must be replaced with an identical

one by the manufacturer, its service

agent or similarly qualied persons

in order to avoid a hazard - risk of

electric shock.

WARNING: Do not locate multiple

portable socket-outlets or portable

power supplies at the rear of the

appliance.

CLEANING AND MAINTENANCE

WARNING: Ensure that the

appliance is switched off and

disconnected from the power supply

before performing any maintenance

operation; never use steam cleaning

equipment - risk of electric shock.

Do not use abrasive or harsh

cleaners such as window sprays,

scouring cleansers, ammable

uids, cleaning waxes, concentrated

detergents, bleaches or cleansers

containing petroleum products

on plastic parts, interior and door

liners or gaskets. Do not use paper

towels, scouring pads, or other harsh

cleaning tools.

7

DISPOSAL OF PACKAGING

MATERIALS

The packaging material is 100% recyclable

and is marked with the recycle symbol .

The various parts of the packaging must

therefore be disposed of responsibly and

in full compliance with local authority

regulations governing waste disposal.

DISPOSAL OF HOUSEHOLD

APPLIANCES

This appliance is manufactured with

recyclable or reusable materials.

Dispose of it in accordance with local waste

disposal regulations.

For further information on the treatment,

recovery and recycling of household

electrical appliances, contact your local

authority, the collection service for

household waste or the store where you

purchased the appliance. This appliance

is marked in compliance with European

Directive 2012/19/EU, Waste Electrical and

Electronic Equipment (WEEE).

By ensuring this product is disposed of

correctly, you will help prevent negative

consequences for the environment and

human health.

The symbol on the product or on the

accompanying documentation indicates

that it should not be treated as domestic

waste but must be taken to an appropriate

collection centre for the recycling of

electrical and electronic equipment.

ENERGY SAVING TIPS

To guarantee adequate ventilation follow

installation instructions.

Insufcient ventilation at the back of the

product increases energy consumption and

decreases cooling efciency.

Frequent door opening might cause an

increase in Energy Consumption.

The internal temperature of the appliance

and the Energy Consumption may be

affected also by the ambient temperature,

as well as location of the appliance.

Temperature setting should take into

consideration these factors. Reduce door

opening to a minimum.

When thawing frozen food, place it in

the refrigerator. The low temperature of

the frozen products cools the food in the

refrigerator.

Allow warm food and drinks to cool down

before placing in the appliance.

Positioning of the shelves in the refrigerator

has no impact on the efcient usage of

energy. Food should be placed on the

shelves in such way to ensure proper air

circulation (food should not touch each other

and distance between food and rear wall

should be kept).

You can increase storage capacity of frozen

food by removing baskets and, if present,

Stop Frost shelf.

Do not worry about noises coming from the

compressor which are normal operation

noises.

The Gulf Conformity Marking on the

product indicates the conformity

with all the requirements of the

Gulf Technical Regulation for Low

Voltage Electrical Equipment and

Appliances BD-142004-01.

8

Thermostat setting

• The thermostat automatically

regulates the inside temperature

of the fridge. By rotating the

knob from position 1 to 5, colder

temperatures can be obtained.

• The “

•

“ position shows

thermostat is closed and no

cooling will take place.

• For short-term storage of food in the fridge, you can set the knob between minimum and

medium positions (1-3).

• For long-term storage of food in the fridge, you can set knob to the medium position (3-

4).

Note that: The ambient temperature, temperature of the freshly stored food and how often

the door is opened, affects the temperature in the fridge. If required, change the temperature

setting.

• When you rst switch on the appliance, you should ideally try to run it without any food in

for 24 hours and not open the door. If you need to use it straight away, try not to store a

large quantity of food inside it.

• If the unit is switched off or unplugged, you must allow at least 5 minutes before

restarting in order not to damage the compressor.

• LARDERS (without star rating): Larders (coolers) do not have a freezer compartment but

can cool down to 4 - 6°C.

Warnings about temperature adjustments

• It is not recommended that you operate your fridge in environments colder than 10°C in

terms of its efciency.

• Temperature adjustments should be made according to the frequency of door openings

and the quantity of food kept inside the fridge.

• Your fridge should be operated up to 24 hours according to the ambient temperature

without interruption after being plugged in to be completely cooled. Do not open doors of

your fridge frequently and do not place much food inside it in this period.

• A 5 minute delaying function is applied to prevent damage to the compressor of your

fridge, when you take the plug off and then plug it on again to operate it or when an

energy breakdown occurs. Your fridge will start to operate normally after 5 minutes.

• Your fridge is designed to operate in the ambient temperature intervals stated in the

standards, according to the climate class stated in the information label. We do not

recommend operating your fridge out of stated temperatures value limits in terms of

cooling effectiveness.

• This appliance is designed for use at an ambient temperature within the 16°C - 32°C

range.

HOW TO OPERATE THE APPLIANCE

9

• The fridge is used for storing fresh food for few days.

• Do not place food in direct contact with the rear wall of the refrigerator. Leave some

space around food to allow the circulation of air.

• Do not place hot food or evaporating liquid in the refrigerator.

• Always make sure food is wrapped or stored in closed containers.

• To reduce humidity and avoid formation of frost, never place liquids in unsealed

containers in the refrigerator.

• We recommend that you loosely wrap meat and store it on the glass shelf just above the

vegetable bin, where the air is cooler.

• Store fruit and vegetable items loose in the crisper containers.

• To prevent the cold air escaping, try not to open the door too often, and not leave the

door open for a long time.

FOOD STORAGE IN THE APPLIANCE

• Disconnect the unit from the power supply before cleaning.

• Do not clean the appliance by pouring water.

• Make sure that no water enters the lamp housing and other electrical components.

• The refrigerator should be cleaned periodically using a solution of bicarbonate of soda

and lukewarm water.

• Clean the accessories separately with soap and water Do not clean them in the

dishwasher.

• Do not use abrasive products, detergents or soaps. After washing, rinse with clean water

and dry carefully. When you have nished cleaning, reconnect the plugto the mains

supply with dry hands.

• Clean the condenser with a broom at least twice a year. This will help you to save on

energy costs and increase productivity.

THE POWER SUPPLY MUST BE DISCONNECTED.

Defrosting

• Defrosting occurs automatically in the fridge

during operation; the water is collected by the

evaporation tray and evaporates automatically.

• The evaporation tray and the water drain hole

should be cleaned periodically with the defrost drain plug to prevent the water from

collecting at the bottom of the fridge instead of owing out.

• You can also clean the drain hole by pouring ½ glass of water down it.

Replacing the light bulb

When replacing the bulb of the fridge;

1. Unplug the unit from the power supply,

2. Press the hooks on the sides of the light cover top

and remove the light cover

3. Change the present light bulb with a new one of

not more than 15 W.

4. Replace the light cover and after waiting 5 minutes plug the unit.

Replacing LED Lighting

If your fridge has LED lighting contact the help desk as this should be changed by

authorized personnel only.

CLEANING AND MAINTENANCE

10

Transportation and changing of Installation position

• The original packages and foamed polystyrene (PS) can be retained if required.

• During transportation, the appliance should be secured with a wide string or a strong

rope. The instructions written on the corrugated box must be followed while transporting.

• Before transporting or changing the installation position, all the moving objects

(ie,shelves,crisper…) should be taken out or xed with bands in order to prevent them

from getting damaged.

Carry your fridge in the upright position.

TRANSPORTATION AND CHANGING OF IN-

STALLATION POSITION

If your fridge is not working properly, it may be a minor problem, therefore check the

following.

The appliance does not operate,

Check if:

• There is a power failure.

• The mains plug is not plugged in properly, or is loose.

• The thermostat setting is on position ““.

• The socket is defective. To check this, plug in another appliance that you know is working

into the same socket.

The appliance performs poorly,

Check if:

• You have overloaded the appliance.

• The door is not closed properly.

• There are not enough ventilation ducts in the kitchen unit as mentioned in the installation

manual.

If there is noise:

The cooling gas which circulates in the fridge circuit may make a slight noise (bubbling

sound) even when the compressor is not running. Do not worry, this is quite normal. If you

hear different sounds, check if:

• The appliance is installed rmly as described in the installation manual.

• Objects on the appliance are vibrating.

If there is water in the lower part of the fridge,

Check if:

• The drain hole for water is not clogged (use defrost drain plug to clean the drain hole).

BEFORE CALLING YOUR AFTER SALES

SERVICE

11

Recommendations

• When there is no power, to prevent any damage to the compressor, you should unplug

the refrigerator. You should delay pluging in 5 – 10 minutes after power is restored.

• If you unplug the refrigerator for any reason you should wait at least 5 min to replug. This

will avoid damage to the refrigerator’s components.

• The cooling unit of your refrigerator is hidden at the rear of the appliance. Therefore,

water droplets or icing may form on the rear surface of your fridge due to the operation

of the compressor at specied intervals. This is normal, there is no need to perform a

defrosting operation unless the icing is excessive.

• If you do not intend to use your fridge for a long time (e.g. in summer holidays), turn the

thermostat to the «

•

» position. After defrosting, clean your fridge and leave the door open

to prevent humidity and smells.

• If the problem persists after you have followed all the instructions above, please consult

to the nearest Authorised Service Centre.

• The appliance you have purchased is designed for domestic use and can only be used

at home and for the stated purposes. It is not suitable for commercial or common use. If

the consumer uses the appliance in a way that does not comply with this, we emphasise

that the manufacturer and the dealer will not be responsible for any repair and failure

within the guarantee period.

Tips for saving energy

1. Install the appliance in a cool, well ventilated room , but not in direct sunlight and not

near a heat source (radiator, cooker ... etc). Otherwise use an insulating plate.

2. Allow warm food and drinks to cool down outside the appliance.

3. Cover drinks or other liquids when placing them in the appliance Otherwise humidity

increases in the appliance. Therefore, the working time gets longer. Also covering drinks

and other liquids helps to preserve smell and taste.

4. Try to avoid keeping the doors open for long periods or opening the doors too frequently

as warm air will enter the cabinet and cause the compressor to switch on unnecessarily

often.

5. Keep the covers of the different temperature compartments (crisper, chiller ... etc ) closed

6. Door gasket must be clean and pliable. Replace gaskets if worn.

12

THE PARTS OF THE APPLIANCE AND THE

COMPARTMENTS

1. Thermostat knob

2. Fridge shelves

3. Crisper cover

4. Crispers

5. Left & Right feet

6. Bottle shelf

7. Door shelves

8. Egg holder

1. Thermostat knob

2. Fridge shelves

3. Crisper cover

4. Crispers

5. Bottle shelf

6. Door shelves

7. Butter shelf cover *

8. Egg holder

* In some models

8

2

3

4

5

7

6

1

8

4

3

5

6

2

7

1

This presentation is only for information about the parts of the appliance.

Parts may vary according to the appliance model.

13

Installation instructions and door reversibility for versions with Rail hinges

! It is recommended that the installation be performed by authorized technical staff

! Before installation, read the instructions carefully.

! Fit the refrigerator/freezer in stable kitchen units only.

! Cabinet dimensions are changed by material of trim ap

1

.

1. If material of trim ap

1

is plastic, look at (Table.1/B1) for cabinet dimensions.

2. If material of trim ap

1

is metal, look at (Table.1/B2) for cabinet dimensions.

! If necessary, reverse the door according to instructions.

1. See g.A for the necessary attachment components.

2. Insert trim ap

1

into slot and screw by screws

6

. (g.D)

3. Pass the power cord through ventilation shaft and position it so that the appliance could

be easily plugged in once it has been installed. (g.B - g.C)

4. Take out the trim gasket

4

located on the side panel of the appliance and stick it on

reverse side of the door hinges of the appliance. (g.D - g.E)

5. Raise the appliance and slide into the kitchen unit.

6. Push the appliance to the reverse side of the door hinges providing that the trim gasket

2

covers the space between the appliance and the kitchen unit.

7. Align the front feet with front surface of the kitchen unit. (g.F)

8. Screw the front feet by using screws

5

. (g.F)

9. Screw trim ap

1

to kitchen unit using screws

5

. (g.G)

10. Screw guides

3

to appliance door with screws

6

. (g.H)

11. Lean appliance door to unit door as it is opened at right angle.

12. Slide rails4 into guides

3

aligning the groove. (g.H)

13. Screw the rails

4

to the unit door with screws

5

. (g.H)

14. Set 1~2 mm gap on handle side between unit itself and unit door by adjusting guides

3

.

That is vital for appliance performance. (g.H)

14

Table 1

2

1

6

Figure A

Figure B Figure C

Figure D Figure E

mm

A B1 (Plastic) B2 (Metal)

875 875 - 895 875 - 883

Table 1

15

Figure GFigure F

Figure H

16

Door reversing

1. Open appliance door

14

. (g.J)

2. Disassemble door hinge

15

and take appliance door

14

to safe place. (g.K)

3. Unscrew door hinge pin

16

and screw it to opposite side rmly and take to safe place.

(g.K.a)

4. Take door lower pin

18

to opposite side. (g.K.b)

5. Take hole plugs

17

to opposite side. (g.K.c)

6. Place appliance door

14

over door lower pin

18

and insert door hinge pin

16

into hinge

hole on appliance door

14

and then screw door hinge

15

rmly onto opposite side of

original position. (g.K)

Figure J

Figure K

17

Installation instructions for product with Hettich hinges

! It is recommended that this installation be performed by authorized technical stuff.

! Before installation, read the instructions carefully.

! Fit the refrigerator/freezer in stable kitchen units only.

! Cabinet dimensions are changed by material of trim ap

1

.

1. If material of trim ap

(1)

is plastic, look at (Table.1/B1) for cabinet dimensions.

2. If material of trim ap

(1)

is metal, look at (Table.1/B2) for cabinet dimensions.

! If necessary, reverse the door according to instructions.

1. See g.A for the necessary attachment components.

2. Open the package. Take gasket spacer

(9)

and brake into three as shown in gureD.

Themiddle part is door hang rail

(10)

. The other two parts are unit door spacers

(11)

. (g.D)

3. Insert trim ap

(1)

into slot and screw by screws

(8)

. (g.E)

4. Pass the power cord through ventilation shaft and position it so that the appliance could-

be easily plugged in once it has been installed. (g.B - g.C)

5. Cut trim gasket

(4)

to the height of the recess and stick it on reverse side of the doorhin-

ges of the appliance. (g.E)

6. Raise the appliance and slide into the kitchen unit.

7. Lean the appliance to the kitchen unit through the hinges and align the front feet with

frontsurface of the kitchen unit. (g.F)

8. Open the appliance door and screw the front feet by using screws

(7)

. (g.G)

9. Screw trim ap

(1)

to kitchen unit using screws

(7)

. (g.G)

10. Screw the hinges to the kitchen unit using screws

(7)

. (g.G)

11. Close the appliance door. Unscrew and remove the nuts

(14)

, washers

(13)

and adjustmen-

tbolts

(12)

from the appliance door. (g.H)

12. Remove the liner for the adhesive part on the door hang rails

(10)

. Place door hang

rails

(10)

on theappliance door by inserting the bosses on the holes of the appliance door,

aligning thefront surfaces of the door hang rails(

10)

and the appliance door parallel to

each other. Letthe door hang rails

(10)

, stick onto the appliance door. (g.H)

13. Slide the door hang

(2)

into door hang rails

(10)

. (g.J - g.K)

14. Take out the liners of the adhesive part on the front side of the door hang

(2)

.

15. Take out the liners of the adhesive part on the unit door spacers

(11)

and and stick them

onto theunit door(15), closer to the upper corners. (g.K)

16. Lean the unit door

(15)

to the door hang

(2)

, aligning the unit door spacers(11) on the

left,right and top edges with the sides of the unit or the doors of the nearer and upper

kitchenunits. (g.K)

17. Make sure that the unit door

(15)

sticks onto the door hang

(2)

. Pull the unit door

(15)

al-

lowing the door hang

(2)

to slide out the door hang rails

(10)

. Observe that the door hang

(2)

stays stuck on the unit door

(15)

. (g.L)

18. Lay down the unit door

(15)

on the oor and screw the door hang

(2)

to the unit door

(15)

by

screws

(7)

. (g.L)

19. To overcome some of the furniture mistakes, there are plastic spacers

(A)

sticked on the

door hang

(2)

. Remove these plastic spacers

(A)

. (g.M)

18

20. Remove the door hang rails

(10)

from the appliance door. Screw the adjustment bol-

ts

(12)

to the holes on the appliance door by leaving the necessary space using unit door

spacer

(11)

. (g.N)

21. Open the appliance door. Place the unit door

(15)

onto the appliance door insertingadjust-

ment bolts(12) into the slots on the door hang

(2)

. (g.N)

22. Place the washers

(13)

and screw the nuts

(14)

onto the adjustment bolts

(12)

. (g.N)

23. 1~2 mm gap between the unit itself and unit door is vital for appliance performance.

Close the door and make the accurate adjustment of the unit door

(15)

by screwing orun-

screwing the adjustment bolts

(12)

for vertical adjustment and by the help of the slotson

the door hang

(2)

for other directions. (g.P1)

24. Place the door bottom xings

(5)

to the bottom of the appliance door between theap-

pliance door and unit door

(15)

. Screw the door bottom xings

(5)

to the appliance doorwi-

th screws

(6)

. (g.O)

25. Screw the door bottom xings

(5)

to the unit door

(15)

by screws

(7)

. (g.O)

26. For the adjustment of the space between the unit upper door

(15)

and the unit itself, you-

can unscrew the screws

(6)

then adjust the space between the appliance upper door

(19)

and unit upper door

(15)

by the spring effect of the door bottom xings

(5)

while screwin-

gback the screws

(6)

.

27. Slide the hang cover

(3)

onto the door hang

(2)

. (g.P2)

19

1

2

3

4

5

6

7

8

1

8

9

10

11

7

mm

A B1 (Plastic) B2 (Metal)

875 875 - 895 875 - 883

Table 1

20

10

14

13

12

10

2

215

15

7

2

11

12

14

13

12

2

3

5

6

7

15

11

10

La page charge ...

Hotpoint I55RM 1110 W 1 Mode d'emploi

Ce manuel convient également à

Hotpoint I55RM 1110 W 1 Mode d'emploi

dans d''autres langues

Autres documents