Extron XTP R HDMI Manuel utilisateur

Catégorie
Commutateurs vidéo
Taper
Manuel utilisateur

Ce manuel convient également à

User Guide
XTP T HDMI
XTP R HDMI
XTP Systems
XTP HDMI Transmitter and Receiver
68-1723-01 Rev. E
01 19
Safety Instructions
Safety Instructions • English
WARNING: This symbol, ,when used on the product, is
intended to alert the user of the presence of uninsulated dangerous
voltage within the product’s enclosure that may present a risk of electric
shock.
ATTENTION: This symbol, , when used on the product, is intended
to alert the user of important operating and maintenance (servicing)
instructions in the literature provided with the equipment.
For information on safety guidelines, regulatory compliances, EMI/EMF
compatibility, accessibility, and related topics, see the Extron Safety and
Regulatory Compliance Guide, part number 68-290-01, on the Extron
website, www.extron.com.
Sicherheitsanweisungen • Deutsch
WARNUNG: Dieses Symbol auf dem Produkt soll den Benutzer
darauf aufmerksam machen, dass im Inneren des Gehäuses dieses
Produktes gefährliche Spannungen herrschen, die nicht isoliert sind und
die einen elektrischen Schlag verursachen können.
VORSICHT: Dieses Symbol auf dem Produkt soll dem Benutzer in
der im Lieferumfang enthaltenen Dokumentation besonders wichtige
Hinweise zur Bedienung und Wartung (Instandhaltung) geben.
Weitere Informationen über die Sicherheitsrichtlinien, Produkthandhabung,
EMI/EMF-Kompatibilität, Zugänglichkeit und verwandte Themen finden Sie in
den Extron-Richtlinien für Sicherheit und Handhabung (Artikelnummer
68-290-01) auf der Extron-Website, www.extron.com.
Instrucciones de seguridad • Español
ADVERTENCIA: Este símbolo, , cuando se utiliza en el producto,
avisa al usuario de la presencia de voltaje peligroso sin aislar dentro del
producto, lo que puede representar un riesgo de descarga eléctrica.
ATENCIÓN: Este símbolo, , cuando se utiliza en el producto, avisa
al usuario de la presencia de importantes instrucciones de uso y
mantenimiento recogidas en la documentación proporcionada con el
equipo.
Para obtener información sobre directrices de seguridad, cumplimiento
de normativas, compatibilidad electromagnética, accesibilidad y temas
relacionados, consulte la Guía de cumplimiento de normativas y seguridad
de Extron, referencia 68-290-01, en el sitio Web de Extron, www.extron.com.
Instructions de sécurité • Français
AVERTISSEMENT : Ce pictogramme, , lorsqu’il est utilisé sur le
produit, signale à l’utilisateur la présence à l’intérieur du boîtier du
produit d’une tension électrique dangereuse susceptible de provoquer
un choc électrique.
ATTENTION : Ce pictogramme, , lorsqu’il est utilisé sur le produit,
signale à l’utilisateur des instructions d’utilisation ou de maintenance
importantes qui se trouvent dans la documentation fournie avec le
matériel.
Pour en savoir plus sur les règles de sécurité, la conformité à la
réglementation, la compatibilité EMI/EMF, l’accessibilité, et autres sujets
connexes, lisez les informations de sécurité et de conformité Extron, réf.
68-290-01, sur le site Extron, www.extron.com.
Istruzioni di sicurezza • Italiano
AVVERTENZA: Il simbolo, , se usato sul prodotto, serve ad
avvertire l’utente della presenza di tensione non isolata pericolosa
all’interno del contenitore del prodotto che può costituire un rischio di
scosse elettriche.
ATTENTZIONE: Il simbolo, , se usato sul prodotto, serve ad
avvertire l’utente della presenza di importanti istruzioni di funzionamento
e manutenzione nella documentazione fornita con l’apparecchio.
Per informazioni su parametri di sicurezza, conformità alle normative,
compatibilità EMI/EMF, accessibilità e argomenti simili, fare riferimento
alla Guida alla conformità normativa e di sicurezza di Extron, cod. articolo
68-290-01, sul sito web di Extron, www.extron.com.
Instrukcje bezpieczeństwa • Polska
OSTRZEŻENIE: Ten symbol, , gdy używany na produkt, ma na celu
poinformować użytkownika o obecności izolowanego i niebezpiecznego
napięcia wewnątrz obudowy produktu, który może stanowić zagrenie
porażenia prądem elektrycznym.
UWAGI: Ten symbol, , gdy używany na produkt, jest przeznaczony do
ostrzegania użytkownika ważne operacyjne oraz instrukcje konserwacji
(obsługi) w literaturze, wyposażone w sprzęt.
Informacji na temat wytycznych w sprawie bezpieczeństwa, regulacji
wzajemnej zgodności, zgodność EMI/EMF, dostępności i Tematy pokrewne,
zobacz Extron bezpieczeństwa i regulacyjnego zgodności przewodnik, część
numer 68-290-01, na stronie internetowej Extron, www.extron.com.
Инструкция по технике безопасности Русский
ПРЕДУПРЕЖДЕНИЕ: Данный символ, , если указан
на продукте, предупреждает пользователя о наличии
неизолированного опасного напряжения внутри корпуса
продукта, которое может привести к поражению электрическим
током.
ВНИМАНИЕ: Данный символ, , если указан на продукте,
предупреждает пользователя о наличии важных инструкций
по эксплуатации и обслуживанию в руководстве,
прилагаемом к данному оборудованию.
Для получения информации о правилах техники безопасности,
соблюдении нормативных требований, электромагнитной
совместимости (ЭМП/ЭДС), возможности доступа и других
вопросах см. руководство по безопасности и соблюдению
нормативных требований Extron на сайте Extron: ,
www.extron.com, номер по каталогу - 68-290-01.
安全说明 简体中文
警告 产品上的这个标志意在警用户该产品机壳内有暴露的危险 电压,
险。
注意 产品上的这个标志意在提示用户设备随附的用户手册中有
重要的操作和维护(维修说明
关于我们产品的安全指南、遵循的规范、EMI/EMF 的兼容性、无障碍
使用的特性等相关内容,敬请访问 Extron 网站 , www.extron.com,参见
Extron 安全规范指南,产品编号 68-290-01
안전 지침 • 한국어
경고: 이 기호 가 제품에 사용될 경우, 제품의 인클로저 내에 있는
접지되지 않은 위험한 전류로 인해 사용자가 감전될 위험이 있음을
경고합니다.
주의: 이 기호 가 제품에 사용될 경우, 장비와 함께 제공된 책자에 나와
있는 주요 운영 및 유지보수(정비) 지침을 경고합니다.
안전 가이드라인, 규제 준수, EMI/EMF 호환성, 접근성, 그리고 관련 항목에
대한 자세한 내용은 Extron 웹 사이트(www.extron.com)의 Extron 안전 및
규제 준수 안내서, 68-290-01 조항을 참조하십시오.
安全記事 • 繁體中文
警告: 若產品上使用此符是為了提醒使用者產品機殼內存
可能會導致觸電之風險的未絕緣危險電壓
注意 品上使用此符號,是為提醒使用設備隨附用戶手冊中
重要的操作和維維修
有關安全性指導方針法規遵EMI/EMF 相容存取範圍和相主題的詳細資
訊,請瀏覽 Extron 網站:www.extron.com然後《Extron 安全性與法規
守手冊準則編號 68-290-01
安全上の注意 日本語
警告: この 製品上に表示されている場合は、筐体内に絶縁され
いない高電圧が流れ、感電の危険があるこていま
意:この が製品上に表されている場合はの取明書
されている重作と保()の示についてユーザーの
を喚起するものです
安全上の注意、法規厳守、EMI/EMF適合性、その他の関連項
スト イト www.extron.com よ り Extron Safety
and Regulatory Compliance Guide』 ( P/N 68-290-01) をご覧ださい。
Copyright
© 2013-2019 Extron Electronics. All rights reserved. www.extron.com
Trademarks
All trademarks mentioned in this guide are the properties of their respective owners.
The following registered trademarks (
®
), registered service marks (
SM
), and trademarks (
TM
) are the property of RGBSystems, Inc. or
ExtronElectronics (see the current list of trademarks on the Terms of Use page at www.extron.com):
Registered Trademarks
(
®
)
Extron, Cable Cubby, ControlScript, CrossPoint, DTP, eBUS, EDID Manager, EDID Minder, Flat Field, FlexOS, Global Configurator,
GlobalScripter, GlobalViewer, Hideaway, HyperLane, IPIntercom, IPLink, KeyMinder, LinkLicense, LockIt, MediaLink, MediaPort, NetPA,
PlenumVault, PoleVault, PowerCage, PURE3, Quantum, Show Me, SoundField, SpeedMount, SpeedSwitch, SystemINTEGRATOR,
TeamWork, TouchLink, V-Lock, VideoLounge, VN-Matrix, VoiceLift, WallVault, WindoWall, XTP, XTPSystems, and ZipClip
Registered Service Mark
(SM)
: S3 Service Support Solutions
Trademarks
(
)
AAP, AFL (Accu-RateFrameLock), ADSP(Advanced Digital Sync Processing), Auto-Image, CableCover, CDRS(ClassD Ripple
Suppression), Codec Connect, DDSP(Digital Display Sync Processing), DMI (DynamicMotionInterpolation), DriverConfigurator,
DSPConfigurator, DSVP(Digital Sync Validation Processing), eLink, EQIP, Everlast, FastBite, FOX, FOXBOX, IP Intercom HelpDesk,
MAAP, MicroDigital, Opti-Torque, PendantConnect, ProDSP, QS-FPC(QuickSwitch Front Panel Controller), Room Agent, Scope-Trigger,
ShareLink, SIS, SimpleInstructionSet, Skew-Free, SpeedNav, StudioStation, Triple-Action Switching, True4K, Vector™ 4K , WebShare,
XTRA, and ZipCaddy
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part15 of the FCC rules. The ClassA limits provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause interference. This interference must be corrected at the expense of the user.
ATTENTION: The Twisted Pair Extension technology works with unshielded twisted
pair (UTP) or shielded twisted pair (STP) cables; but to ensure FCC Class A and CE
compliance, STP cables and STP Connectors are required.
For more information on safety guidelines, regulatory compliances, EMI/EMF
compatibility, accessibility, and related topics, see the “Extron Safety and Regulatory
Compliance Guide” on the Extron website.
VCCI-A Notice
の装置はA情報技術装置です の装置を家庭環境で使用す電波妨害を
があの場合には使用者が適切な対策を講ず要求があ
CI -A
ixXTP T HDMI Transmitter and XTP R HDMI Receiver • Contents
Contents
Introduction............................................................ 1
Guide Overview .................................................. 1
XTP T HDMI Transmitter and XTP R HDMI
Receiver Description .......................................... 1
System Compatibility .......................................... 2
Features ............................................................. 3
Installation .............................................................. 4
Rear Panel Connectors ....................................... 4
Transmitter Rear Panel Connectors ................. 4
Receiver Rear Panel Connectors .................... 6
Connection Details ............................................. 8
HDMI Connection ........................................... 8
TP Cable Termination and
Recommendations ........................................ 9
RS-232 and IR Communication .................... 11
Power Connection ........................................ 12
Operation .............................................................. 15
Front Panel Features ......................................... 15
Transmitter Front Panel Features ................... 15
Receiver Front Panel Features ...................... 16
HDMI Audio Switch .......................................... 16
EDID ................................................................. 17
Audio Output Overview ..................................... 17
Reset Mode ...................................................... 18
SIS Configuration and Control ........................ 19
Host Device Connection ................................... 19
SIS Overview .................................................... 19
Host-to-Device and Device-to-Host
Communication ........................................... 19
Error Responses ........................................... 19
Using the Command and Response Tables
for SIS Commands ...................................... 20
Symbol Definitions ........................................ 20
Command and Response Tables for the
Transmitter SIS Commands ............................. 21
Audio Configuration Commands ................... 21
EDID Commands .......................................... 22
Advanced Configuration Commands ............ 22
Command and Response Tables for the
Receiver SIS Commands ................................. 24
Audio Configuration Commands ................... 24
Advanced Configuration Commands ............ 24
XTP System Configuration Software ............. 26
Software Installation.......................................... 26
Software Download Center Page .................. 26
Software Product Page ................................. 27
Software Operation........................................... 28
Connection ................................................... 28
Menu Bar ..................................................... 29
Transmitter Configuration .............................. 32
Receiver Configuration .................................. 36
Reference Information ...................................... 38
Mounting .......................................................... 38
Tabletop Mounting ........................................ 38
Furniture Mounting........................................ 38
Rack Mounting ............................................. 38
XTP T HDMI Transmitter and XTP R HDMI Receiver • Contents x
XTP T HDMI Transmitter and XTP R HDMI Receiver • Introduction 1
Introduction
This section contains general information about this guide, the Extron XTP T HDMI
Transmitter and XTP R HDMI Receiver. Topics in this section include:
Guide Overview
XTP T HDMI Transmitter and XTP R HDMI Receiver Description
System Compatibility
Features
Guide Overview
This guide contains installation, operation, control, and reference information for the
XTP T HDMI Transmitter and XTP R HDMI Receiver.
In this guide, the terms “XTP T HDMI” and “transmitter” refer to the XTP T HDMI Transmitter.
The terms “XTP R HDMI” and “receiver” refer to the XTP R HDMI Receiver.
XTP T HDMI Transmitter and XTP R HDMI Receiver Description
The XTP T HDMI and XTP R HDMI send and receive video, audio, bidirectional
RS-232 and IR, and Ethernet signals over a shielded twisted pair cable. They are
HDCP-compliant and support 1080p @ 60 Hz Deep Color and 1920x1200 signals, and
embedded HD lossless audio formats. They work with Extron XTP devices in matrix or
point-to-point applications for signal distribution and long-distance transmission (up to
330 feet) between remote endpoints, using shielded twisted pair cable.
Either device can be powered locally or remotely through an Extron Power Injector or XTP
matrix switcher (see Power Connection on page 12).
Both devices can be controlled through Extron Simple Instruction Set (SIS) commands (see
SIS Configuration and Control on page 19) or the XTP Configuration Software (see XTP
System Configuration Software on page 26).
XTP T HDMI Transmitter and XTP R HDMI Receiver • Introduction 2
The following diagram shows ways the XTP T HDMI and XTP R HDMI can be integrated in
an XTP matrix application.
FLEX I/O
SWITCHED 12VDC
40W MAX TOTAL
LAN
1234
COM1
TXRX
RTS CTS
IR/SERIAL
1
SGSG
2
RELAY
3
SGSG
+-+-
+-+-
4 1 21 2 3 4
3 4
5
SGSG
6 7
SGSG
8 5 6 7 8
COM2
TXRX
COM3
TXRX
COM7
TXRX
COM4
TXRX
RTS CTS
COM5
TXRX
COM6
TXRX
COM8
TXRX
eBUS
+V
PWR OUT = 12W
D-S+S
5A MAX
100-240V 50-60Hz
100-240V 1.3A, 50-60Hz
CLASS 2 WIRING
1
2
17TT
AUDIO/VIDEO
APPARATUS
XPA 1002
C US
LEVEL
1
12
1
2
LIMITER/
PROTECT
SIGNAL
2
INPUTS
OUTPUT
REMOTE
0 0
10V 50 mA
VOL/MUTE
STANDBY
LISTED
POWER
12V
INPUTS
HDMI
--A MAX
RxTx
RS-232 IR
RxTx
+−+
LR
LOOP-THRU
RESET
OVER XTP
AUDIO
OFF
XTP T HDMI
HDMI AUDIO
ON
LAN
ACT LINK
SIG LINK
XTP OUT
POWER
12V
INPUTS
HDMI
--A MAX
RxTx
RS-232 IR
RxTx
+−+
LR
LOOP-THRU
RESET
OVER XTP
AUDIO
OFF
XTP T HDMI
HDMI AUDIO
ON
LAN
ACT LINK
SIG LINK
XTP OUT
POWER
12V
INPUTS
HDMI
--A MAX
RxTx
RS-232 IR
RxTx
+−+
LR
LOOP-THRU
RESET
OVER XTP
AUDIO
OFF
XTP T HDMI
HDMI AUDIO
ON
LAN
ACT LINK
SIG LINK
XTP OUT
POWER
12V
OUTPUTS
HDMI
--A MAX
RxTx
RS-232 IR
RL
RxTx
-+-+
1
2
OVER XTP
AUDIO
OFF
HDMI AUDIO
ON
XTP R HDMI
S/PDIF
RELAYS
RESET
LAN
ACT LINK
SIG LINK
XTP IN
Flat Panel
Display
HDMI
RS-232
Ethernet
XTP R HDMI
Long Distance XTP
Receiver for HDMI
POWER
12V
OUTPUTS
HDMI
--A MAX
RxTx
RS-232 IR
RL
RxTx
-+-+
1
2
OVER XTP
AUDIO
OFF
HDMI AUDIO
ON
XTP R HDMI
S/PDIF
RELAYS
RESET
LAN
ACT LINK
SIG LINK
XTP IN
Flat Panel
Display
HDMI
IR
Ethernet
XTP R HDMI
Long Distance XTP
Receiver for HDMI
STANDBY/ON
PQLS HDMIOPEN/CLOSE FL OFF
USB
I
N
P
U
T
S
O
U
T
P
U
T
S
OUT
XTP CP 4o SA
AUDIO
LRLR LRLR
OUT
LAN
ACT
LINK
RESET
100-240V
50-60Hz
--A MAX
REMOTE
RS 232/RS422
DISCONNECT POWER
CORD BEFORE
SERVICING
IN
XTP CP 4i VGA
AUDIO
LRLR LRLR
IN
IN
XTP CP 4i VGA
AUDIO
LRLR LRLR
IN
IN
IN
XTP CP 4i
RS-232 IR
Tx Rx Tx Rx
RS-232 IR
Tx Rx Tx Rx
RS-232 IR
Tx Rx Tx Rx
RS-232 IR
Tx Rx Tx Rx
SIG LINK
XTP
PWR
ACT LINK
LAN
XTP
PWR
ACT LINK
LAN
XTP
PWR
ACT LINK
LAN
XTP
PWR
ACT LINK
LAN
IR/RS-232 OVER XTP
IN
IN
XTP CP 4i
RS-232 IR
Tx Rx Tx Rx
RS-232 IR
Tx Rx Tx Rx
RS-232 IR
Tx Rx Tx Rx
RS-232 IR
Tx Rx Tx Rx
SIG LINK
SIG LINK
SIG LINK
SIG LINK
SIG LINK
SIG LINK
SIG LINK
XTP
PWR
ACT LINK
LAN
XTP
PWR
ACT LINK
LAN
XTP
PWR
ACT LINK
LAN
XTP
PWR
ACT LINK
LAN
IR/RS-232 OVER XTP
OUT
OUT
XTP CP 4o
RS-232 IR
Tx Rx Tx Rx
RS-232 IR
Tx Rx Tx Rx
RS-232 IR
Tx Rx Tx Rx
RS-232 IR
Tx Rx Tx Rx
SIG LINK
XTP
PWR
ACT LINK
LAN
XTP
PWR
ACT LINK
LAN
XTP
PWR
ACT LINK
LAN
XTP
PWR
ACT LINK
LAN
IR/RS-232 OVER XTP
OUT
OUT
XTP CP 4o
RS-232 IR
Tx Rx Tx Rx
RS-232 IR
Tx Rx Tx Rx
RS-232 IR
Tx Rx Tx Rx
RS-232 IR
Tx Rx Tx Rx
SIG LINK
SIG LINK
SIG LINK
SIG LINK
SIG LINK
SIG LINK
SIG LINK
XTP
PWR
ACT LINK
LAN
XTP
PWR
ACT LINK
LAN
XTP
PWR
ACT LINK
LAN
XTP
PWR
ACT LINK
LAN
IR/RS-232 OVER XTP
IN
XTP CP 4i DVI Pro
AUDIO
LRLR LRLR
IN
IN
XTP CP 4i DVI Pro
AUDIO
LRLR LRLR
IN
OUT
XTP CP 4o DVI Pro
AUDIO
LRLR LRLR
OUT
OUT
XTP CP 4o DVI Pro
AUDIO
LRLR LRLR
OUT
IN
XTP CP 4i HDMI
AUDIO
LRLR LRLR
IN
IN
XTP CP 4i HDMI
AUDIO
LRLR LRLR
IN
OUT
XTP CP 4o HDMI
AUDIO
LRLR LRLR
OUT
OUT
XTP CP 4o HDMI
AUDIO
LRLR LRLR
OUT
Laptop
PC
HDMI
Ethernet
Ethernet
Ethernet
Ethernet
Stereo Audio
IR
Shielded Twisted Pair
Cable
RS-232
IR
Blu-ray
AV Control
Network
IPCP 505
IP Link Control
Processor
XTP T HDMI
Long Distance XTP
Transmitter for HDMI
HDMI
Ethernet
XTP T HDMI
Long Distance XTP
Transmitter for HDMI
HDMI
Ethernet
XTP T HDMI
Long Distance XTP
Transmitter for HDMI
TLP 1000TV
10" Tabletop TouchLink
Touchpanel
XPA 1002
Stereo Power Amplier
SI 28
Surface Mount
Speakers
XTP CrossPoint 3200
Modular Digital
Matrix Switcher
House Network Switch
Ethernet
Figure 1. XTP T HDMI and XTP R HDMI Matrix Application Example
System Compatibility
The XTP T HDMI and XTP R HDMI are compatible with XTP Systems, but the maximum
video resolution may be limited with different XTP devices. See the table below for maximum
video resolutions and refresh rates for various XTP Systems.
Output
Non-4K 4K Fiber 4K Plus
Input
Analog 1920x1200 @ 60 Hz 1920x1200 @ 60 Hz 1920x1200 @ 60 Hz
Non-4K Digital 2048x1080 @ 60 Hz 2048x1080 @ 60 Hz 2048x1080 @ 60 Hz
4K Fiber 2048x1080 @ 60 Hz 4096x2160 @ 24 Hz 4096x2160 @ 24 Hz
4K PLUS 2048x1080 @ 60 Hz 4096x2160 @ 24 Hz 4096x2160 @ 60 Hz
XTP T HDMI Transmitter and XTP R HDMI Receiver • Introduction 3
Features
Reliable cable infrastructure — Provides high reliability and maximum performance
on an economical and easily installed cable infrastructure.
Support for computer-video to 1920x1200, including HDTV 1080p/60 Deep
Color and 2K signals — Maintains superior image quality at the highest resolutions.
Shielded twisted pair cable compatibility — Optimized for use with common
shielded twisted pair cable types. XTP Systems fully support a maximum transmission
distance of 330 feet (100 meters) for all compatible resolutions when used with shielded
twisted pair cable. Shielded twisted pair cabling with solid center conductor sizes of
24 AWG or better is recommended for optimal performance.
Bidirectional RS-232 and IR insertion — Allows a remote display to be controlled
without the need for additional cabling through bidirectional RS-232 and IR control
signals inserted into the XTP output.
HDMI specification features — Support data rates up to 6.75 Gbps, Deep Color up
to 12-bit, 3D, and HD lossless audio formats.
HDCP compliance — Ensures display of content-protected media and interoperability
with other HDCP-compliant devices.
EDID Minder — Automatically manages EDID communication between connected
devices. It ensures that all sources power up properly and reliably outputs content for
display.
Key Minder — Authenticates and maintains continuous HDCP encryption between
input and output devices to ensure quick and reliable switching in professional AV
environments, while enabling simultaneous distribution of a single source signal to one
or more displays.
Ethernet extension — Centralized 10/100 Ethernet communication can be
implemented via an Ethernet pass-through port to reduce the amount of independent
network drops required within a system.
Remote power capability — Allows the devices to be powered by an
XTP CrossPoint Matrix Switcher or XTP Power Injectors to simplify integration.
Multiple embedded audio formats — Provides reliable operation with HDMI sources,
compatible with a broad range of multi-channel audio signals.
XTP compatibility — Provides a completely integrated solution for multiple digital and
analog formats through XTP integrated system products. XTP is a flexible, reliable signal
switching and distribution system.
UL 2043 plenum rated — Meets UL 2043 for smoke and heat release for installation
within a plenum airspace above a drop ceiling - power supply excluded.
Above-the-ceiling placement conceals the device to prevent theft, and is convenient for
installing equipment when space inside the room is limited.
Transmitter HDMI loop-through with selectable audio control — Features an
active HDMI output with support for embedded audio for connection to a local monitor.
Transmitter selectable analog stereo audio input embedding — Supports
balanced or unbalanced audio for extended transmission by embedding stereo audio
into the signal stream. This feature enables direct connection of separate stereo audio
signals from a laptop, Blu-ray Disc™ player, or other device.
Receiver HDMI audio de-embedding with analog stereo and digital S/PDIF
audio outputs Digital HDMI audio is made available as a balanced or unbalanced
analog stereo signal on captive screw connectors or a S/PDIF connector.
XTP T HDMI Transmitter and XTP R HDMI Receiver • Installation 4
Installation
This section contains the installation procedures for the XTP T HDMI and XTP R HDMI.
Topics in this section include:
Rear Panel Connectors
Connection Details
Rear Panel Connectors
Transmitter Rear Panel Connectors
POWER
12V
HDMI
1.0 A MAX
Rx GTx
RS-232 IR
RxTx
+−+
LR
LOOP-THRU
RESET
AUDIO
OFF
ON
AUDIO
SIG LINK
XTP OUT
INPUTS
OVER XTP
LAN
ABCD E
F
G
A
HDMI input connector (see page 4)
B
HDMI loop-through connector
(see page 4)
C
Analog audio input connector
(see page 5)
D
RS-232 and IR Over XTP connector
(see page 5)
E
XTP output connector (see page 5)
F
LAN connector (see page 5)
G
Power connector and LED (see
page 6)
Figure 2. XTP T HDMI Rear Panel Connectors
Transmitter inputs
NOTES:
For HDMI cables, the maximum cable length is 15 feet (4.6 meters).
Use Extron LockIt Cable Lacing Brackets to secure HDMI connectors to the device
(see HDMI Connection on page 8).
A
HDMI input connector — Connect a digital video source device to the HDMI
input connector. It accepts HDMI, DVI (with an appropriate adapter), or dual mode
DisplayPort video sources.
B
HDMI loop-through connector — Connect a digital video display to the HDMI
loop-through connector for a local display of the HDMI input (see HDMI Audio Switch
on page 16 to select local audio output options). A display that is not HDCP-compliant
displays a green screen when HDCP encrypted content is sent to it.
XTP T HDMI Transmitter and XTP R HDMI Receiver • Installation 5
C
Analog audio input connector — Connect an audio source to the 5-pole captive
screw connectors (see figure 2,
C
on the previous page). Wire the connector as
shown in figure 3.
Unbalanced Audio Input
Balanced Audio Input
Tip
Ring
Tip
Ring
Slee
ves
Tip
Sleeve
Sleeve
Tip
LR
LR
Do not tin the wires!
Figure 3. Audio Input Wiring
Transmitter XTP interconnection
D
RS-232 Over XTP port To pass bidirectional serial signals between
XTP-compatible devices, connect a control device to the 5-pole captive
screw connector (see figure 2,
D
on the previous page). The port includes
only the 3 poles labeled “RS-232.”
IR Over XTP port — To transmit and receive IR signals (up to 56 kHz),
connect a control device to the 5-pole captive screw connector (see
figure 2,
D
on the previous page). This port includes the 2 poles
labeled “IR” and shares the ground pole with the RS-232 port.
NOTE: RS-232 and IR data can be transmitted simultaneously (see RS-232 and IR
Communication on page 11 for wiring details).
E
XTP output connector — Connect a twisted pair cable to this RJ-45 connector (see
figure 2,
E
on the previous page) on the XTP T HDMI and the XTP input port on
another XTP device to pass all signals (see TP Cable Termination and
Recommendations on page 9). This cable carries the following signals:
Digital video
Digital audio
Bidirectional RS-232 and IR commands
Remote power
Ethernet communication
System communication
Signal LED indicator — Lights green when the transmitter outputs an
XTP signal to a compatible receiver or matrix switcher.
Link LED indicator — Lights yellow when XTP devices are connected
and communication is established.
ATTENTION:
Do not connect this connector to a computer data or telecommunications
network.
Ne connectez pas ce connecteur à un réseau de données informatiques ou à
un réseau de télécommunications.
XTP remote power is intended for indoor use only. No part of the network that
uses XTP remote power should be routed outdoors (see Remote power on
page 14).
XTP à distance est destiné à une utilisation en intérieur seulement. Aucune
partie du réseau qui utilise l’alimentation XTP à distance ne peut être routée en
extérieur (voir Remote power à la page 14).
F
LAN connector — Connect a control device or device to be controlled to the
pass-through LAN connector (see figure 2,
F
on the previous page) for 10/100Base-T
Ethernet communication. LEDs on the connector indicate link and activity status.
IR
Tx Rx G Tx Rx
RS-232
IR
Tx Rx G Tx Rx
RS-232
Signa
l
Link
XTP T HDMI Transmitter and XTP R HDMI Receiver • Installation 6
Transmitter power
G
Power connector and LED — Connect the external 12 V, 1.5 A power supply to the
2-pole captive screw connector (see figure 2,
G
on page 4). For wiring considerations,
see Power Connection on page 12. The Power LED lights to indicate the device is
receiving power.
NOTE: The XTP T HDMI can also be powered remotely (see Remote power on
page 14).
Receiver Rear Panel Connectors
POWER
12V
1.0 A MAX
Rx GTx
RS-232 IR
RL
RxTx
-+-+
1
2
AUDIO
ON
AUDIO
RESET
OVER XTP
OUTPUTS RELAYS
SIG LINK
XTP IN
HDMI
OFF
S/PDIF
LAN
A
B
CDEFGH
A
XTP input connector (see page 6)
B
LAN connector (see page 7)
C
RS-232 and IR Over XTP
connector (see page 7)
D
HDMI output connector
(see page 7)
E
Analog audio output connector (see
page 7)
F
S/PDIF output connector (see page 7)
G
Relay connector (see page 8)
H
Power connector and LED (see
page 8)
Figure 4. XTP R HDMI Rear Panel Connectors
Receiver XTP interconnection
A
XTP Input connector — Connect a twisted pair cable to this RJ-45 connector on the
XTP R HDMI and the XTP output port on another XTP device to pass all signals (see TP
Cable Termination and Recommendations on page 9). This cable carries the
following signals:
Digital video
Digital audio
Bidirectional RS-232 and IR commands
Remote power
Ethernet communication
System communication
Signal LED indicator — Lights green when the receiver is receiving an
active XTP input signal.
Link LED indicator — Lights yellow when XTP devices are connected
and communication is established.
ATTENTION:
Do not connect this connector to a computer data or telecommunications
network.
Ne connectez pas ce connecteur à un réseau de données informatiques ou à
un réseau de télécommunications.
XTP remote power is intended for indoor use only. No part of the network that
uses XTP remote power should be routed outdoors (see Remote power on
page 14).
XTP à distance est destiné à une utilisation en intérieur seulement. Aucune
partie du réseau qui utilise l’alimentation XTP à distance ne peut être routée en
extérieur (voir Remote power à la page 14).
Signa
l
Link
XTP T HDMI Transmitter and XTP R HDMI Receiver • Installation 7
B
LAN connector — Connect a control device or device to be controlled to the receiver
for 10/100 Ethernet communication through this pass-through port (see figure 4.
B
on
the previous page). LEDs on the connector indicate link and activity status.
C
RS-232 Over XTP port To pass bidirectional serial signals between
XTP-compatible devices, connect a control device to the 5-pole captive
screw connector (see figure 4.
C
on the previous page). The port includes
only the 3 poles labeled “RS-232.”
IR Over XTP port — To transmit and receive IR signals (up to 56 kHz),
connect a control device to the 5-pole captive screw connector (see
figure 4.
C
on the previous page). This port includes the 2 poles labeled
“IR” and shares the ground pole with the RS-232 port.
NOTE: RS-232 and IR data can be transmitted simultaneously (see RS-232 and IR
Communication on page 11 for wiring details).
Receiver outputs
D
HDMI output connector — Connect a display device to the female HDMI connector
(see figure 4,
D
on the previous page). It supports HDMI or DVI (with an appropriate
adapter) signals.
NOTES:
The maximum cable length is 15 feet (4.6 meters).
Use an Extron LockIt Cable Lacing Bracket to secure the HDMI connector to
the device (see HDMI Connection on the next page).
E
Analog audio output connector — Connect a balanced or unbalanced, stereo or
mono audio output device to the 3.5 mm, 5-pole captive screw connector (see
figure 4,
E
on the previous page) for analog audio output. Wire the connector as
shown in figure 5.
Do not tin the wires!
Balanced Audio Output
Tip
Ring
Tip
Ring
Slee
ves
Unbalanced Audio Output
Tip
No Ground Here
No Ground Here
Tip
Sleeves
LR
LR
Figure 5. Audio Output Wiring
ATTENTION:
For unbalanced audio, connect the sleeves to the contact ground. Do not
connect the sleeves to the negative (-) contacts.
Pour l’audio asymétrique, connectez les manchons au contact au sol. Ne pas
connecter les manchons aux contacts négatifs (–).
F
S/PDIF output connector — Connect an audio device to the female orange RCA
connector for digital S/PDIF audio output (see figure 4,
F
on the previous page). The
type of audio present on this output is dictated by the following (see Audio Output
Overview on page 17 for supported audio formats on the S/PDIF output):
The audio format selected on the source material or device.
The source device automatically outputting an audio format through EDID.
IR
Tx Rx G Tx Rx
RS-232
IR
Tx Rx G Tx Rx
RS-232
XTP T HDMI Transmitter and XTP R HDMI Receiver • Installation 8
Receiver relay
G
Relay connector — Connect equipment that can be controlled via momentary or
latching contact, like projector screens or lifts, to normally open relays (see figure 4,
G
on page 6).
ATTENTION:
Do not exceed 24 V at 1.0 A for each port.
Ne pas dépasser 24volts à 1,0A pour chaque port.
Receiver power
H
Power connector and LED — Connect the external 12 V, 1.5 A power supply to the
2-pole captive screw connector (see figure 4,
H
on page 6). For wiring considerations,
see Power Connection on page 12. The Power LED lights to indicate the device is
receiving power.
NOTE: The XTP R HDMI can also be powered remotely (see Remote power on
page 14).
Connection Details
HDMI Connection
To secure the HDMI cable to the HDMI input connector, use an Extron LockIt Cable Lacing
Bracket and a tie wrap.
3
1
2
3
4
5
Figure 6. Installing the LockIt Cable Lacing Bracket
1. Plug the HDMI cable into the panel connection (see figure 6,
1
).
2. Loosen the HDMI connection mounting screw from the panel (
2
) enough to allow the
LockIt to be placed over it. The screw does not have to be removed.
3. Place the LockIt on the screw and against the HDMI connector (
3
), and then tighten
the screw to secure the bracket.
4. Loosely place the included tie wrap around the HDMI connector and the LockIt (
4
).
5. While holding the connector securely against the cable lacing bracket, use pliers or
similar tools to tighten the tie wrap, then remove any excess length (
5
).
ATTENTION:
Connect and pull the tie wraps until they are secure. Do not overtighten.
Connectez et tirez les serre-câbles jusqu’à ce qu’ils soient sécurisés. Ne pas
trop serrer.
XTP T HDMI Transmitter and XTP R HDMI Receiver • Installation 9
TP Cable Termination and Recommendations
Use the following pin configurations for twisted pair cables.
12345678
RJ-45
Connector
Inser
t Twisted
Pair Wires
Pins:
Pin
1
2
3
4
5
6
7
8
Wire color
White-green
Green
White-orange
Blue
White-blue
Orange
White-brown
Brown
Wire color
T568A T568B
White-orange
Orange
White-green
Blue
White-blue
Green
White-brown
Brown
TIA/EIA-T568B
Pin Wire Color
1 White-orange
2 Orange
3 White-green
4 Blue
5 White-blue
6 Green
7 White-brown
8 Brown
Figure 7. TP Cable Termination
Supported cables
The XTP T HDMI and XTP R HDMI are compatible with shielded twisted pair (F/UTP,
SF/UTP, and S/FTP) cable.
ATTENTION:
Do not use Extron UTP23SF-4 Enhanced Skew-Free AV UTP cable or STP201
cable to link the XTP products.
N’utilisez pas le câble AV Skew-FreeUTP version améliorée UTP23SF d’Extron ou
le câble STP201 pour relier les produits XTP.
To ensure FCC Class A and CE compliance, STP cables and STP connectors are
required.
Afin de s’assurer de la compatibilité entre FCC ClasseA et CE, les câbles STP et
les connecteurs STP sont nécessaires.
XTP T HDMI Transmitter and XTP R HDMI Receiver • Installation 10
Cable recommendations
Extron recommends using the following practices for XTP communication to achieve full
transmission distances up to 330 feet (100 meters) and reduce transmission errors.
Use the following Extron XTP DTP 24 SF/UTP cables and connectors for the best
performance:
XTP DTP 24/1000 Non-Plenum 1000’ (305 m) spool 22-236-03
XTP DTP 24P/1000 Plenum 1000’ (305 m) spool 22-235-03
XTP DTP 24 Plug Package of 10 101-005-02
If not using XTP DTP 24 cable, at a minimum, Extron recommends 24 AWG, solid
conductor, STP cable with a minimum bandwidth of 400 MHz.
Terminate cables with shielded connectors to the TIA/EIA-T568B standard (see
figure 7 on the previous page).
Limit the use of more than two pass-through points, which may include patch points,
punch down connectors, couplers, and power injectors. If these pass-through points
are required, use shielded couplers and punch down connectors.
NOTE: When using STP cable in bundles or conduits, consider the following:
Do not exceed 40% fill capacity in conduits.
Do not comb the cable for the first 20 meters, where cables are straightened,
aligned, and secured in tight bundles.
Loosely place cables and limit the use of tie wraps or hook-and-loop fasteners.
Separate twisted pair cables from AC power cables.
XTP T HDMI Transmitter and XTP R HDMI Receiver • Installation 11
RS-232 and IR Communication
The RS-232 and IR Over XTP connector is for pass-through transmission of serial signals,
such as projector control signals, and infrared data. To pass bidirectional serial command
signals between XTP-compatible devices, connect a control device to the three poles
(Tx, Rx, and G) under “RS-232” of the 5-pole captive screw connector. To transmit and
receive IR signals, connect a control device to the three poles (G, Tx, and Rx) under “IR.”
The ground (G) pole is shared.
NOTE: RS-232 and IR data can be transmitted or received simultaneously (see figure 8
for wiring considerations).
Tx/Rx
Pins
RxTx
RS-232 IR
RxTx
TxRx
RxTx
IR Device
RS-232 Device
G
G
G
Figure 8. RS-232 and IR Over XTP Connector Wiring Configuration
ATTENTION: The length of the exposed wires in the stripping process is important.
ATTENTION : La longueur des câbles exposés est importante lorsque l’on entreprend
de les dénuder.
The ideal length is 3/16 inch (5 mm).
La longueur idéale est de 5mm (3/16inches).
Any longer and the exposed wires may touch, causing a short circuit between
them.
S’ils sont un peu plus longs, les câbles exposés pourraient se toucher et provoquer
un court circuit.
Any shorter and the wires can be easily pulled out even if tightly fastened by the
captive screws.
S’ils sont un peu plus courts, ils pourraient sortir, même s’ils sont attachés par les
vis captives.
XTP T HDMI Transmitter and XTP R HDMI Receiver • Installation 12
Power Connection
Apply power to the transmitter or receiver locally with the provided power supply (if
necessary, see figure 9 for wiring considerations) or remotely (through the XTP connector)
with a power injector or an XTP CrossPoint matrix switcher.
Local power
SECTION A–A
AA
Power Supply
Output Cord
2-Pole Captive Screw
Connector
Ridges
Smooth
Tie
Wrap
3/16”
(5 mm) Max.
Figure 9. Power Wiring
Both the transmitter and receiver can be powered by a local power supply. See the
notifications on the next page for local power considerations.
XTP T HDMI Transmitter and XTP R HDMI Receiver • Installation 13
WARNING: The DC output cables must be kept separate from each other while the
power supply is plugged in. Remove power before wiring.
AVERTISSEMENT : Les câbles de sortie CC doivent être séparés les uns des autres
tant que la source d’alimentation est branchée. Coupez l’alimentation avant d’effectuer
les raccordements.
ATTENTION:
This product is intended for use with a UL Listed power source marked “Class 2”
or “LPS” rated 12 VDC, 1.0 A minimum, 48 VDC (PoE), minimum 0.35 A, or an
Extron UL Listed XTP remote power source. Always use a power supply supplied
by or specified by Extron. Use of an unauthorized power supply voids all regulatory
compliance certification and may cause damage to the supply and the unit.
Ce produit est destiné à une utilisation avec une source d’alimentation certifiée UL
de classe 2 ou LPS et calibrée à 12 Vcc, 1,0 A minimum, 48 Vcc (PoE),
0,35 A minimum, ou une source d’alimentation délocalisée XTP Extron certifiée UL.
Utilisez toujours une source d’alimentation fournie par Extron. L’utilisation d’une
source d’alimentation non autorisée annule toute conformité réglementaire et peut
endommager la source d’alimentation ainsi que l’unité.
Unless otherwise stated, the AC/DC adapters are not suitable for use in air handling
spaces or in wall cavities. The installation must always be in accordance with the
applicable provisions of National Electrical Code ANSI/NFPA 70, article 725 and
the Canadian Electrical Code part 1, section 16. The power supply shall not be
permanently fixed to a building structure or similar structure.
Sauf mention contraire, les adaptateurs AC/DC ne sont pas appropriés pour
une utilisation dans les espaces d’aération ou dans les cavités murales. Cette
installation doit toujours être en accord avec les mesures qui s’applique au National
Electrical Code ANSI/NFPA70, article725, et au Canadian Electrical Code,
partie1, section16. La source d’alimentation ne devra pas être fixée de façon
permanente à une structure de bâtiment ou à une structure similaire.
Power supply voltage polarity is critical. Incorrect voltage polarity can damage the
power supply and the unit. The ridges on the side of the cord identify the power
cord negative lead.
La polarité de la source d’alimentation est primordiale. Une polarité incorrecte
pourrait endommager la source d’alimentation et l’unité. Les stries sur le côté du
cordon permettent de repérer le pôle négatif du cordon d’alimentation.
The length of the exposed (stripped) copper wires is important. The ideal length is
3/16 inch (5 mm).
La longueur des câbles exposés est primordiale lorsque l’on entreprend de les
dénuder. La longueur idéale est de 5mm (3/16inch).
TIP: Do not tin the stripped power supply leads. Tinned wires are not as secure in the
captive screw connectors and could be pulled out.
XTP T HDMI Transmitter and XTP R HDMI Receiver • Installation 14
Remote power
Either device can be powered remotely through an XTP Power Injector or through an XTP
matrix switcher.
ATTENTION:
XTP remote power is intended for indoor use only. No part of the network that uses
XTP remote power should be routed outdoors.
L’alimentation à distance XTP est destinée à un usage en intérieur uniquement.
Aucune partie du réseau qui utilise l’alimentation XTP à distance ne peut être routée
en extérieur.
Power injector
To power either device remotely with an XTP Power Injector, power one device locally (see
Local power on page 12) and connect an XTP Power Injector to the XTP cable run along
the XTP ports (see the XTP Power Injector User Guide at www.extron.com for more
installation information).
POWER
12V
HDMI
0.7A MAX
Rx GTx
RS-232 IR
RxTx
+
+
LR
LOOP THRU
RESET
AUDIO
OFF
ON
AUDIO
XTP T HDMI
LAN
SIG LINK
XTP OUT
INPUTS
OVER XTP
LAN
SIG LINK
XTP IN
POWER
12V
HDMI
1A MAX
Rx GTx
RS-232 IR
RxTx
+−+
LR
1
2
OVER XTP
AUDIO
OFF
ON
S/PDIF
RESET
XTP R HDMI
RELAYS
OUTPUTS
AUDIO
XTP
PWR
XTP PWR
100-240V
50/60 Hz
0.4A MAX
Power
XTP R HDMI
XTP Receiver
XTP PI 100
XTP Power
Injector
Shielded Twisted Pair
Cable
REMOTE
POWER
12V Local Power
Supply
XTP T HDMI
XTP Transmitter
Figure 10. Typical Pont-to-Point Application with Remote Power
NOTE: The power injector provides remote power up to 330 feet with a shielded twisted
pair cable with 24 AWG wire.
XTP CrossPoint matrix switcher
XTP CrossPoint matrix switchers have a fixed amount of power available to provide remote
power to connected XTP devices (see the XTP CrossPoint matrix switcher user guide at
www.extron.com for more details). To manage available power from the XTP CrossPoint
matrix switcher, use the XTP System Configuration Software with the XTP CrossPoint matrix
switcher.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45

Extron XTP R HDMI Manuel utilisateur

Catégorie
Commutateurs vidéo
Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues