Nexgrill 720-0894F Manuel utilisateur

Marque: Nexgrill

Modèle: 720-0894F

Catégorie: Barbecues

Taper: Manuel utilisateur

Ce manuel convient également à

720-0925

19000584A1

WARNING

To reduce the risk of fire, burn hazard or other injury,

read the manual carefully and completely before

using your grill.

WARNING

FOR OUTDOOR USE ONLY.

WARNING

This grill is not intended to be

installed in or on recreational

vehicles and/or boats.

Example only: SERIAL #__________MFG. DATE___________PURCHASE DATE:_______________

Questions, problems, missing parts? Before returning to your retailer, call our customer service

department at 1-800-913-8999 in USA, 8 a.m. - 5 p.m., PST, Monday - Friday

MODEL / MODÈLE / MODELO # 720-0894F

LP Gas Grill page 1-13

PARRILLA A GAS PROPANO pagina 14-

GRIL AU GAZ DE PÉTROLE LIQUÉFIÉ

page 27-42

Safety Precautions--------------------------------

Lighting Instructions----------------------------

Cooking Instruction----------------------------------

Cooking Chart-----------------------------------------

Cleaning and Maintenance--------------------------

Troubleshooting--------------------------------------

Warranty------------------------------------------------

Parts Diagram ---------------------------------------

Parts List-----------------------------------------------

Table of Contents

State of California Proposition 65 Warnings:

WARNING: To operate, this equipment requires

the use of propane gas, which contains the

chemical Benzene which is known to the State

of California to cause cancer and other

reproductive harm.

WARNING: This product contains one or more

chemicals known to the State of California to

cause cancer.

WARNING: This product contains one or more

chemicals known to the State of California to

cause birth defects or other reproductive harm.

In the State of Massachusetts, the following

installation instructions apply:

 Installations and repairs must be performed

by a qualified or licensed contractor, plumber,

or gasfitter qualified or licensed by the State of

Massachusetts.

 If using a ball valve, it shall be a T-handle

type.

 A flexible gas connector, when used, must

not exceed 3 feet.

ASSEMBLER: Leave this manual with consumer.

CONSUMER: Keep this manual for future reference.

ASEMBLADOR: Deje este manual al consumidor.

CONSUMIDOR: Conserve este manual para futuras referencias .

ASSEMBLEUR: Laissez ce manuel avec le consommateur.

CONSOMMATEUR: Conserver ce manuel à titre de référence ultérieure .

WARNING

Failure to comply with these instructions could result in a

fire or explosion that could cause serious bodily injury,

death, or property damage.

WARNING

Your grill will get very hot. Never lean over the

cooking area while using your grill. Do not touch

cooking surfaces, grill housing, lid or any other grill

parts while the grill is in operation, or until the gas grill

has cooled down after use.

Failure to comply with these instructions may

result in serious bodily injury.

WARNING

1. Do not store or use gasoline or other

flammable liquids or vapors in the

vicinity of this or any other appliance.

2. An LP cylinder not connected for use

shall not be stored in the vicinity of this

or any other appliance.

DANGER

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open flame.

3. Open lid.

4. If odor continues, keep away from the

appliance and immediately call your gas

supplier or your fire department.

Grill Installation Codes

The installation must conform with local codes or, in the

absence of local codes, with either the national fuel gas

code, ANSI Z 223.1/NFPA 54, Natural gas and propane

installation code, CSA B149.1, or propane storage and

handling code, B149.2, or the standard for Recreational

vehicles, ANSI A 119.2, and CSA Z240 RV series

recreational vehicle code, as applicable.

LP gas grill models are designed for use with a

standard 20 lb. Liquid Propane Gas tank, not included

with grill. Never connect your gas grill to an LP gas tank

that exceeds this capacity.

Precautions

A tank of approximately 12 inches in diameter by 18-1/2 inches

high is the maximum size LP gas tank to use.

You must use an OPD gas tank which offers an Overfill

Prevention Device.

This safety feature prevents the tank from being overfilled

which can cause malfunction of the LP gas tank, pressure

regulator and/or grill.

The LP gas tank must be constructed and marked in

accordance with specifications of the U.S. Dept. of

Transportation (DOT). In Canada, the LP gas tank must meet

the National Standard of Canada ,CAN/CSA-B339 , Cylinders ,

spheres and Tubes for Transportation of Dangerous Goods

and Commission .

1. The LP gas tank must have a shutoff valve, terminating in an

LP gas supply tank valve outlet, that is compatible with a Type

1 tank connection device. The LP gas tank must also have a

safety relief device that has a direct connection with the vapor

space of the tank.

2. The tank supply system must be arranged for vapor

withdraw.

3. The LP gas tank used must have a collar to protect the tank

valve.

Proper Placement and Clearance of Grill

Never use your gas grill in a garage, porch, shed, breezeway

or any other enclosed area. Your gas grill is to be used

outdoors only, at least 36 inches from the back and side of

any combustible surface. Your gas grill should not be used

under overhead combustible construction . Do not obstruct the

flow of ventilation air around the gas grill housing.

• Do not install this outdoor gas grill in or on recreational

vehicles or boats

• Keep outdoor gas grill area clear and free from combustible

materials, gasoline and other flammable vapors and liquids

• Do not obstruct the flow of combustion and ventilation air.

Check for this each time prior to using grill.

• Never connect an unregulated LP gas tank to your gas grill.

The gas pressure regulator assembly supplied with your gas

grill is adjusted to have an outlet pressure of 11” water column

(W.C.) for connection to an LP gas tank.

• Only use the pressure regulator and the hose assembly

supplied with your gas grill. Replacement pressure regulators

and hose assemblies must be those specified in this manual.

• Have your LP gas tank filled by a reputable propane

gas dealer and visually inspected and re-qualified at

each filling.

• Do not store a spare LP gas tank under or

near this appliance.

• Never fill the tank beyond 80 percent full . If this

information is not followed exactly a fire causing death

or serious injury may occur.

• Always keep LP gas tanks in an upright position.

• Do not store or use gasoline or other flammable vapors

and liquids in the vicinity of this gas grill.

• Do not subject the LP gas tank to excessive heat.

•

Never store an LP gas tank indoors. If you store your

gas grill in the garage or other indoor location, always

disconnect the LP gas tank first and store it safely

outside.

• Place dust cap on cylinder valve outlet whenever the

cylinder is not in use. Only install the type of dust cap

on the cylinder valve outlet that is provided with the

cylinder valve. Other types of caps or plugs may result

in leakage of propane.

• LP gas tanks must be stored outdoors in a well-

ventilated area and out of reach of children.

Disconnected LP gas tanks must not be stored in a

building, garage or any other enclosed area.

• When your gas grill is not in use the gas must be

turned off at the LP gas tank.

• The pressure regulator and hose assembly must be

inspected before each use of the grill. If there is

excessive abrasion or wear or if the hose is cut, it must

be replaced prior to the grill being used again.

• Keep the gas pressure regulator hose away from hot

grill surfaces and dripping grease. Avoid unnecessary

twisting of hose. Visually inspect the hose prior to each

use for cuts, cracks, excessive wear or other damage.

If the hose appears damaged do not use the gas grill.

Call 1-800-913-8999 for a replacement hose.

• Never light your gas grill with the lid closed or before

checking to ensure the burner tubes are fully seated

over the gas valve orifices.

• Never allow children to operate your grill.

Always keep the LP cylinder at

90° (upright) orientation to

provide vapor withdraw.

WARNING

A strong gas smell, or the hissing sound of gas

indicates a serious problem with your gas grill or the

LP gas tank. Failure to immediately follow the steps

listed below could result in a fire or explosion that

could cause serious bodily injury, death, or property

damage.

• Shut off gas supply to the gas grill.

• Turn the control knobs to OFF position.

• Put out any flame with a proper fire extinguisher.

• Open Grill Lid.

• Get away from the LP gas tank.

• Do not try to fix the problem yourself.

• If odor continues or you have a fire you can not

extinguish, call your fire department. Do not call near

the LP gas tank because your telephone is a form of

electrical device and could create a spark resulting in

fire and/or explosion.

NOTE: The normal flow of gas through the pressure

regulator and hose assembly can create a humming

noise. A low volume of noise is perfectly normal and

will not interfere with operation of the grill. If humming

noise is loud and excessive you may need to purge

air from the gas line or reset the pressure regulator

excess gas flow device. This purging procedure

should be done every time a new LP gas tank is

connected to your grill. For help with this procedure

refer to page 7, Item 4 of “If Grill Still Fails To Light”,

or call the Grill Information Center at 1-800-913-8999.

CAUTION: Spiders and small insects occasionally spin

webs or make nests in the grill burner tubes during transit

and warehousing. These webs can lead to gas flow

obstruction which could result in a fire in and around burner

tubes. This type of fire is known as “FLASH-BACK” and can

cause serious damage to your grill and create an unsafe

operating condition for the user.

Although an obstructed burner tube is not the only cause of

“FLASH-BACK”, it is the most common cause.

To reduce the chance of “FLASH-BACK”, you must clean

the burner tubes before assembling your grill, and at least

once a month in late summer or early fall when spiders are

most active. Also perform this burner tube cleaning

procedure if your grill has not been used for an extended

period of time.

See Cleaning Burner Tubes and Ports on page # 11.

Visually check the burner flames prior to each use. The flames should

look like picture, if they do not, refer to the cleaning burner tubes and

ports, see page 11 of this manual.

CAUTION: Beware of Flash-Back Burner Flame Check

1. Make a 50/50 (soap/water) mild soap solution.

2. Turn the control knobs to full OFF position; then turn gas ON at

supply tank.

Apply the soap solution with a clean brush to all gas connections.

See below. If growing bubbles appear in the solution the

connections are not properly sealed. Check each fitting and

tighten or repair as necessary.

4. If you have a gas connection leak you cannot repair, turn gas

OFF at supply tank, disconnect fuel line from your grill and call

1-800-913-8999 or your gas supplier for repair assistance.

5. Also apply soapy solution to the tank seams. See below. If

growing bubbles appear, shut tank OFF and do not use or move

it! Contact an LP gas supplier or your fire department for

assistance.

Gas Connection Leak Check

Gas Tank Leak Check

Checking for LP gas leaks

Never test for leaks with a flame. Prior to first use, at the beginning

of each season, or every time your LP gas tank is changed, you

must check for gas leaks.

WARNING

Failure to open grill lid during the lighting

procedure could result in a fire or explosion that

could cause serious bodily injury, death, or

property damage.

Grill Lighting Instruction

3. Be sure all gas connections are securely tightened.

4. Turn on gas supply.

5. Open the grill main lid.

6. Push and turn any main burner control knob to

/HIGH, at the same time, press and hold electronic

ignition button to light the burner. Once the burner is lit,

release the electronic ignition button and knob.

7. If the burner does not light after 5 seconds, turn knob

to OFF. Turn gas OFF at LP tank and wait 5 minutes

for gas to clear. Then turn gas ON at tank and repeat

step 6.

8. If burner still does not light, see Match Lighting section

and If Grill Still Fails to Light section on following page.

9. To light additional burners, turn burner knob(s) to

/HIGH . Push and hold electronic ignition button to

light burner. Adjust knob(s) to desired setting.

Grill Lighting Instructions for Main Burners

1. Do not smoke while lighting grill or checking gas supply

connections.

2. Be sure that LP gas tank is sufficiently full.

WARNING

Never lean over the grill cooking area while lighting

your gas grill. Keep your face and body a safe

distance (at least 18 inches) from the cooking grid

surface when lighting your grill by match.

If Grill Still Fails To Light

1. Check gas supply and connections for leaks. Check that

all wire connections are secure.

2. Repeat basic lighting procedure. If your grill still fails to

operate, turn the gas off at source, turn the control knobs to

OFF, then check the following:

• Misalignment of burner tubes over orifices

Correction: Reposition burner tubes over orifices.

• Plugged orifice

Correction: Remove burners from grill, carefully lift each

burner up and away from gas valve orifice. Remove the

orifice from gas valve and gently clear any obstruction with

a fine wire. Then reinstall all orifices, burners, and cooking

components.

3. If an obstruction is suspected in grill burner valves,

please call for repair service at 1-800-913-8999.

4. If the grill still does not light you may need to purge air

from the gas line or reset the pressure regulator excess gas

flow device. Note: This procedure should be done every

time a new LP gas tank is connected to your grill.

To purge air from your gas line and/or reset the

pressure regulator excess gas flow device:

• Turn all control knobs to the OFF position.

• Turn off the gas at the tank valve.

• Disconnect pressure regulator from LP gas tank.

• Let unit stand for 5 minutes.

• Reconnect pressure regulator to the LP gas tank.

• Turn the tank valve on slowly until ¼ to ½ open.

• Open the grill lid.

• Push and turn any control knob to .

• Turn control knobs to until all the burners are lit

•

You may start to use the grill

5. If all checks or corrections have been made and you still

have questions about operating your gas grill, call the Grill

Information Center at 1-800-913-8999

WARNING

Should a “FLASH-BACK” fire occur in/or around the

burner tubes, follow the instructions below. Failure

to comply with these instructions could result in a

fire or explosion that could cause serious bodily

injury, death, or property damage.

• Shut off gas supply to the gas grill.

• Turn the control knobs to OFF position.

• Put out any flame with a proper fire extinguisher.

• Open grill lid.

• Once the grill has cooled down, clean the burner tubes

and burners according to the cleaning instructions found

on page 11.

•If the burner will not light after several attempts then the burner

can be match lit, before using the match allow 5 minutes for any

accumulated gas to dissipate.

•Clip a paper match on one end of the lighting rod.

•Light match.

•Hold lighting rod and insert lighted match right next to the

burner ports or ceramic file.

•Push and turn the designated control knob to /HIGH.

•Burner should ignite immediately.

Match light

Congratulations

Your Nexgrill gas grill is now ready for use. Before

the first use and at the beginning of each season

(and whenever the LP gas tank has been changed):

1. Read all safety, lighting and operating instructions.

2. Check gas valve orifices, burner tubes and burner

ports for any obstructions.

3. Perform gas leak check according to instructions

found on next page of the manual.

Important

Before cooking on your grill the first time, wash

cooking grids and cooking rack with warm , soapy

water. Rinse and dry thoroughly. Season with

cooking oil regularly. After cooking is completed, turn

grill to HIGH setting for 3 to 5 minutes to burn off

excess grease or food residue.

DISCONNECTING THE LIQUID PROPANE CYLINDER

Turn the grill burner valves “OFF” and make sure the

grill is cool.

Turn the Liquid Propane Cylinder valve “OFF” by

turning clockwise until it stops.

Detach the pressure regulator assembly from the

cylinder valve by turning the quick coupling nut

counterclockwise.

Place dust cap on cylinder valve outlet whenever the

cylinder is not in use. Only install the type of dust cap

on the cylinder valve outlet that is provided with the

cylinder valve. Other types of caps or plugs may

result in leakage of propane.

Hold coupling nut and regulator

as shown for proper connection

to LP tank valve.

Nipple has to be centered

into the LP tank valve.

5. Hold regulator and insert nipple into LP tank valve. Hand-

tighten the coupling nut, holding regulator in a straight line with

LP tank valve so as not to crossthread the connection.

6. Turn the coupling nut clockwise and tighten to a full stop. The

regulator will seal on the back-check feature in the LP tank

valve, resulting in some resistance. An additional one-half to

three-quarters turn is required to complete the connection.

Tighten by hand only – do not use tools.

NOTE:

If you cannot complete the connection, disconnect regulator and

repeat steps 5 and 6. If you are still unable to complete the

connection, do not use this regulator! Call 1-800-913-8999 for

assistance.

WARNING

Do not leave the grill unattended.

Your grill will get very hot. Never lean over the

cooking area while using your grill. Do not touch

cooking surfaces, grill housing. Grill Lid or any other

grill parts while the grill is in operation, or until the

grill has cooled down after use. Failure to comply

with these instructions may result in serious bodily

injury.

Burn-off

Before cooking on your gas grill for the first time, you will

want to “burn off” the grill to eliminate any odor or foreign

matter. Just ignite the burners, lower the Lid, and operate

grill on the HIGH setting for 3 to 5 minutes.

Cooking Temperatures

High setting: Only use this setting for fast warm-up,

searing steaks or chops and for burning food residue off

the grill after cooking is complete. Never use the HIGH

setting for extended cooking.

Medium to Low Settings: Most recipes specify medium

to low settings, including all smoking, rotisserie cooking

and for cooking lean cuts such as fish.

NOTE: Temperature settings will vary with the

temperature and the amount of wind outside your home.

Direct Cooking

The direct cooking method can be used with the supplied

cooking grids and food placed directly over the lit grill

Burners. The method is ideal for searing and whenever

you want meat, poultry or fish to have and open-flame

barbecued taste. Deep frying and smoking are also best

cooked in this manner because they require direct heat.

Indirect Cooking

To cook indirectly, the food should be placed on the

left or right side of your grill with the burner lit on the

opposite side.

Flare-ups

The fats and juices dripping from grilled food can cause

flare-ups. Since flare-ups impart a favorably, distinctive

taste and color to food cooked cover an open flame,

they should be accepted up to a point. Nevertheless,

uncontrolled flaring can result in a ruined meal.

WARNING

Do not line the bottom of the grill housing with aluminum

foil, sand or any substance that will restrict the flow of

grease into the grease tray.

Failure to comply with these instructions could result in a

fire or explosion which could cause serious bodily injury,

death, or property damage.

Cooking Instructions

FOOD Weight or thickness Temperature Time Special instructions and tips

Vegetables NA Medium 8 to 20 minutes

Slice or chop vegetables and dot with butter or

margarine. Wrap tightly in heavy duty foil. Grill

turning occassionally.

Potatoes Whole Medium 40 to 60 minutes

Wrap individually in heavy duty foil. Cook

rotating occassionally.

Meat/Steaks 1/2 to 3/4 inches High-Medium 4 to 15 minutes

Pre heat grill for 15-20 minutes then sear

steaks on each side for two minutes. Next

grill 3 to 5 minutes on each side or until

desired doneness.

Ground Meats 1/2 to 3/4 inches Medium 8 to 15 minutes

Grill turning once when juices rise to the

surface or until desired amount of doneness.

Do not leave hamburgers unattended since a

flare-up could occur quickly.

Ribs 1/2 or full rack Medium 20 to 40 minutes

Grill turning occassionally. During last few

minutes brush with barbecue sauce, turn

several times.

Hot dogs NA Medium 5 to 10 minutes

Grill turning four times. 2-4 minutes on each of

four sides.

Poultry-Cut 1/4 to 1/2 pounds Low or Medium 20 to 40 minutes

Grill turning occassionally. During last few

minutes brush with barbecue sauce if desired,

turn several times.

Low or 1 to 1-1/2 hours

Use poultry stand and brush frequently as

desired

Medium 40 to 60 minutes

Use poultry stand and brush frequently as

desired

Fish 3/4 to 1 inch Medium 8 to 15 minutes

Grill turning once to desired doneness. Brush

with melted butter, margarine or oil.

Poultry Whole

2 to 3 pounds

Grill Cooking Chart

To ensure a proper working unit the following proper care

and maintenance is suggested. Caution: Regular cleaning of

the bowl assembly is required to prevent grease build-up.

Cleaning Cooking Grids

We suggest you wash your cooking grids in a mild soap and

warm water solution. You can use a wash cloth or soft brush

to clean your cooking grids.

Cleaning Heat diffusers

Periodically you should wash the heat diffusers in a soap and

warm water solution. Use a soft brush to remove stubborn

burnt-on cooking residue. The heat diffusers should be dry

before you reinstall them.

Cleaning Grease Tray

The grease tray should be emptied and wiped down

periodically and washed in a mild detergent and warm water

solution. A small amount of sand or cat litter may be placed

in bottom of grease tray to absorb the grease.

Check the grease tray frequently, don’t allow excess grease

to accumulate and overflow out of the grease tray.

Annual Cleaning of Grill Interior

Burning-off the grill after every use will keep it ready for your

next use. However, once a year you should give the entire

grill a thorough cleaning to keep it in top operating condition.

Follow these steps.

1. Turn all burner valves to full OFF position.

2. Turn LP gas tank valve to full OFF position.

3. Detach LP gas hose and pressure regulator assembly

from your gas grill. Inspect for any damage and replace as

necessary with manufacturer replacement part number found

on parts list.

4. Remove and clean heat diffusers, cooking grids and grill

burners.

5. Cover each gas valve orifice with aluminum foil.

6. Brush inside and bottom of grill with a nylon brush, and

wash with a mild soap and warm water solution. Rinse

thoroughly and let dry.

7. Remove the aluminum foil, then reinstall heat diffusers,

and cooking grids.

8. Reconnect gas source and observe burner flame for

correct operation.

Cleaning Exterior Surface

We suggest you wash your grill using a mild soap and warm

water solution. You can use a wash cloth or sponge for this

process. Do not use abrasives or a brush that might remove

finish during the cleaning process.

Cleaning Exterior Stainless Steel Surfaces

Weathering and extreme heat can cause exterior stainless steel

surfaces to turn tan in color. Machine oils used in manufacturing

process of stainless steel can also cause this tanning color. Use a

stainless steel cleaner to polish stainless steel surfaces of your grill.

Never use abrasive cleaners or scrubbers because they will scratch

and damage your grill.

Cleaning Burner Tubes and Burner Ports

To reduce the chance of “FLASH-BACK” the procedure below should

be followed at least once a month in late summer or early fall when

spiders are most active or when your grill has not been used for a

period of time.

1. Turn all burner valves and gas tank valve to off position.

2. Detach the LP gas pressure regulator assembly from your gas grill.

3. Remove cooking grids, heat diffusers, and grease tray from the grill.

4. Remove the R clip from the burner and lift the burners up and away

from the gas valve orifice.

5. Using a bent stiff wire in the shape of a hook , air hose or a bottle

brush, run it through the burner tube and inside several times to

remove any debris.

6. Replace burners, see illustration below.

Step 1. Replace R clip.

Step 2. Take off R clip which fixes burner at the end side.

Step 3. Locate the new burner onto the orifice.

(a) Insert the burner over the main burner gas valve .

(b) Make sure the orifice stud (C1) is inside the burner venture (D1)

as shown in (Fig.23).

Step 4. Secure the main burner on the back wall use R clip, and fix on

ignite wire.

Cleaning and Maintenance

BEFORE CALLING FOR SERVICE

If the grill does not function properly, use the following check list before calling for service.

You should inspect the burners at least once a year or immediately after any of the following conditions occur:

Regardless of which burner cleaning procedure you use, we

recommend you also complete the following steps to help

prolong burner life.

1. Use a fiber pad or nylon brush to clean the entire outer surface

of each burner until free of food residue and dirt.

WARNING

Spiders and insects can nest inside the burners of the grill

and disrupt gas flow. This very dangerous condition could

cause a fire behind the valve panel, thereby damaging the

grill and making it unsafe for operation. Inspect the grill at

least twice a year.

2. Clean any clogged ports with a stiff wire, such as an open

paper clip.

3. Inspect each burner for damage (cracks or holes) and if such

damage is found, order and install a new burner. After installation

check to ensure that gas valve orifices are correctly placed inside

the ends of the burner tubes.

Troubleshooting

PROBLEMS WHAT TO DO

Check to see if LP tank is empty.

Clean wires and/or electrode by rubbing

with alcohol and clean swab.

Wipe with dry cloth.

Make sure the wire is connected to

electrode assembly.

Do other burners on the unit operate?

Check to see if other burners operate. If

so, check the gas orifice on the

malfunctioning burner for an obstruction.

Burner flame is yellow or orange, in

combination with the odor of gas.

Refer to Clean Burner Tubes and Burner

Ports on page 11. If problem still exists,

call 1-800-913-8999.

Low heat with knob in “HI” position. Is the fuel hose bent or kinked?

Is the grill in a dusty area?

Is there adequate gas supply available?

If it is only one burner that appears low,

does the orifice or burner need cleaning?

Is the gas supply or gas pressure low?

Grill won’t light when the control knob is

rotated.

WARNING

The location of the burner tube with respect to the orifice is vital

for safe operation. Check to ensure the orifice is inside the

burner tube before using the gas grill. If the burner tube does not

fit over the valve orifice, lighting the burner may cause explosion

and/or fire.

MANUFACTURER/ FABRICANTE/ FABRICANTE:Nexgrill Industries, Inc.14050 Laurelwood Pl. Chino, CA

91710

LIMITED WARRANTY (Model # 720-0894F)

The manufacturer warrants to the original consumer-purchaser only

that this product (Model #720-0894F) shall be free from defects in workmanship

and materials after correct assembly and under normal and reasonable home use for the periods indicated below beginning on the date of

purchase. The manufacturer reserves the right to require photographic evidence of damage, or that defective parts be returned, postage and/or

freight pre-paid by the consumer, for review and examination. Nexgrill’s obligation is limited to repair, replacement, or depreciated value, at the

option of Nexgrill.

• TUBE BURNERS: 1 year LIMITED warranty against perforation.

• COOKING GRIDS and FLAME TAMERS: 1 year LIMITED warranty; does not cover dropping, chipping, scratching, or surface damage.

• STAINLESS STEEL PARTS: 1 year LIMITED warranty against perforation; does not cover cosmetic issues like surface corrosion, scratches and

rust.

•

ALL OTHER PARTS: 1 year LIMITED warranty (Includes, but not limited to, valves, frame, housing, cart, control panel, igniter, regulator, hoses)

*Does not cover chipping, scratching, cracking surface corrosion, scratches or rust.

Upon consumer supplying proof of purchase as provided herein, Manufacturer will repair or replace the parts which are proven defective during the

applicable warranty period. Parts required to complete such repair or replacement shall be free of charge to you except for shipping costs, as long

as the purchaser is within the warranty period from the original date of purchase. The original consumer-purchaser will be responsible for all

shipping charges of parts replaced under the terms of this limited warranty. This limited warranty is applicable in the United States and Canada

only, is only available to the original owner of the product and is not transferable. Manufacturer requires reasonable proof of your date of purchase.

Therefore, you should retain your sales receipt and/or invoice. If the unit was received as a gift, please ask the gift-giver to send in the receipt on

your behalf, to the below address. Defective or missing parts subject to this limited warranty will not be replaced without registration or proof of

purchase. This limited warranty applies to the functionality of the product ONLY and does not cover cosmetic issues such as scratches, dents,

corrosions or discoloring by heat, abrasive and chemical cleaners or any tools used in the assembly or installation of the appliance, surface rust, or

the discoloration of stainless steel surfaces. Surface rust, corrosion, or powder paint chipping on metal parts that does not affect the structural

integrity of the product is not considered a defect in workmanship or material and is not covered by this warranty. This limited warranty will not

reimburse you for the cost of any inconvenience, food, personal injury or property damage. If an original replacement part is not available, a

comparable replacement part will be sent. You will be responsible for all shipping charges of parts replaced under the terms of this limited warranty.

MANUFACTURER WILL NOT PAY FOR:

•Service calls to your home.

•Repairs when your product is used for other than normal, single-family household or residential use.

•Damage resulting from accident, alteration, misuse, lack of maintenance/cleaning, abuse, fire, flood, acts of God, improper installation, and

installation not in accordance with electrical or plumbing codes or misuse of product.

•Any food loss due to product failures.

•Replacement parts or repair labor costs for units operated outside the United States or Canada.

•Pickup and delivery of your product.

•Postage fees or photo processing fees for photos sent in as documentation.

•Repairs to parts or systems resulting from unauthorized modifications made to the product.

•The removal and/or reinstallation of your product.

•

Shipping cost, standard or expedited, for warranty/non warranty and replacement parts.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES

Repair or replacement of defective parts is your exclusive remedy under the terms of this limited warranty. Manufacturer will not be responsible for

any consequential or incidental damages arising from the breach of either this limited warranty or any applicable implied warranty, or for failure or

damage resulting from acts of God, improper care and maintenance, grease fire, accident, alteration, replacement of parts by anyone other than

manufacturer, misuse, transportation, commercial use, abuse, hostile environments (inclement weather, acts of nature, animal tampering), improper

installation or installation not in accordance with local codes or printed manufacturer instructions.

THIS LIMITED WARRANTY IS THE SOLE EXPRESS WARRANTY GIVEN BY THE MANUFACTURER. NO PRODUCT PERFORMANCE

SPECIFICATION OR DESCRIPTION WHEREVER APPEARING IS WARRANTED BY MANUFACTURER EXCEPT TO THE EXTENT SET FORTH

IN THIS LIMITED WARRANTY. ANY IMPLIED WARRANTY PROTECTION ARISING UNDER THE LAWS OF ANY STATE, INCLUDING IMPLIED

WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR USE, IS HEREBY LIMITED IN DURATION TO THE

DURATION OF THIS LIMITED WARRANTY.

Neither dealers nor the retail establishment selling this product has any authority to make any additional warranties or to promise remedies in

addition to or inconsistent with those stated above. Manufacturer's maximum liability, in any event, shall not exceed the documented purchase price

of the product paid by the original consumer. This warranty only applies to units purchased from an authorized retailer and or re-seller. NOTE:

Some states do not allow an exclusion or limitation of incidental or consequential damages, so some of the above limitations or exclusions may not

apply to you; this limited warranty gives you specific legal rights as set for herein. You may also have other rights which vary from state to state.

If you wish to obtain performance of any obligation under this limited warranty, you should write to:

Nexgrill Customer Relations

14050 Laurelwood PI

Chino, CA 91710

All consumer returns, parts orders, general questions, and troubleshooting

assistance can be acquired by calling U.S.A:1-800-913-8999

19000584A1

MODEL / MODÈLE / MODELO # 720-0894F

ADVERTENCIA

Para reducir el riesgo de incendio, el peligro de

quemaduras u otras lesiones, lea atentamente y por

completo el manual antes de utilizar su parrilla.

ADVERTENCIA

PARA USO EN EXTERIORES

SOLAMENTE.

ADVERTENCIA

Esta parrilla no fue diseñada con la

intención de ser instalada en

vehículos recreacionales ni en

botes.

Sólo a modo de ejemplo: SERIE Nº ________ FECHA DE FAB ________ COMPRA : _________

¿Tiene preguntas, problemas o le faltan piezas? Antes de devolver el producto a la tienda

minorista, llame a nuestro departamento de servicio al cliente al 1-800-913-8999 en Estados

Unidos, de lunes a viernes de 8 a.m. a 5 p.m., hora del Pacífico

LP Gas Grill page 1-13

PARRILLA A GAS PROPANO pagina 14-

GRIL AU GAZ DE PÉTROLE LIQUÉFIÉ

page 27-42

Precauciones de seguridad-----------------------------

Instrucciones de cocción---------------------------------

Tabla de cocción en la parrilla------------------------

Limpieza y mantenimiento -------------------------------

Localización y resolución de problemas --------------

Garantía------------------------------------------------------

Diagrama de piezas --------------------------------------

Listado de piezas ------------------------------------------

Índice

Advertencias de la Proposición 65 del estado de

California:

ADVERTENCIA: Para operar, este equipo requiere el

uso de gas propano, que contiene la sustancia química

benceno identificada por el estado de California como

causante de cáncer u otro tipo de daño en la función

reproductora.

ADVERTENCIA: Este producto contiene una o más

sustancias químicas identificadas por el estado de

California como causantes de cáncer.

ADVERTENCIA: Este producto contiene una o más

sustancias químicas identificadas por el estado de

California como causantes de defectos congénitos o

algún otro tipo de daños en la función reproductora.

En el estado de Massachusetts se aplican las

siguientes instrucciones de instalación:

Las instalaciones y reparaciones se deben efectuar

por un contratista, plomero o gasista calificado o

licenciado por el estado de Massachusetts.

Si se usa una válvula de bola, debe ser un tipo de

manigueta T.

Si se usa un conector de gas flexible no debe exceder

de 3 pies.

ADVERTENCIA

En caso de que estas instrucciones no se cumplieran,

ello podría dar como resultado un incendio o una

explosión que podría causar lesiones corporales graves,

la muerte o daños a la propiedad.

ADVERTENCIA

Su parrilla llegará a tener una temperatura muy

elevada. Nunca se incline sobre el área de cocción

mientras use la parrilla. No toque las superficies de

cocción, la carcasa de la parrilla, la tapa o cualquier otra

pieza de la parrilla mientras esta esté operando o hasta

que la parrilla de gas se haya enfriado luego de usarla.

El incumplimiento de estas instrucciones puede dar

como resultado lesiones corporales graves.

ADVERTENCIA

1. No almacene ni use gasolina u otros líquidos

o vapores inflamables en las cercanías de

este o cualquier otro dispositivo.

2. No se debe almacenar en las cercanías de

este o cualquier otro dispositivo un cilindro

de propano líquido (LP, por sus siglas en

inglés) que no esté conectado para su uso.

PELIGRO

En caso de que usted huela gas :

1. Cierre el suministro de gas del dispositivo.

2. Apague cualquier tipo de llama abierta.

3. Abra la tapa.

4. Si el olor persiste, manténgase alejado del

dispositivo y llame inmediatamente a su

proveedor del servicio de gas o al

departamento de bomberos.

Precauciones

Códigos de instalación de la parrilla

La instalación debe cumplir con los códigos locales o, en ausencia de

ellos, con todo código de gas combustible a nivel nacional, norma

ANSI Z 223.1/NFPA 54, el código de instalación para gas propano y

gas natural, norma CSA B149.1 o el código de manipulación y

almacenamiento de propano, norma B149.2, o las normas para

vehículos recreativos, norma ANSI A 119.2, y el código de vehículos

recreativos serie CSA Z240 RV, según corresponda.

Los modelos de parrilla de gas LP están diseñados para que se usen

con un tanque de gas propano líquido de 20 lb, que no está incluido

con la parrilla. Nunca conecte su parrilla de gas a un tanque de gas LP

que supere esta capacidad.

Un tanque de 12 pulgadas de diámetro por 18½

pulgadas de alto aproximadamente es el tamaño

máximo del tanque de gas LP para usar en la prrilla.

Debe usar un tanque de gas OPD que brinda un Dispositivo

de Prevención por Sobrecarga.

Esta función de seguridad evita que el tanque se sobrecargue lo

que puede ocasionar un funcionamiento incorrecto del tanque

de gas LP, del regulador y/o de la parrilla.

El tanque de gas LP debe estar construido y marcado de

acuerdo con las especificaciones del Departamento de

Transporte de Estados Unidos (DOT, por sus siglas en inglés).

En Canadá, el tanque de gas LP debe cumplir con las Normas

Nacionales de Canadá, norma CAN/CSA-B339, sobre cilindros,

esperas y tubos de la Comisión y Transporte de Mercadería

Peligrosa.

1. El tanque de gas LP debe tener una válvula de cierre que

cancele la salida del suministro de gas LP de la válvula del

tanque y que sea compatible con un dispositivo de conexión

para tanque Tipo 1. El tanque de gas LP también debe contar

con un dispositivo de escape de seguridad que tenga una

conexión directa con el espacio de vapor del tanque.

2. El sistema de suministro del tanque debe estar adaptado para

la salida de vapores.

3. El tanque de gas LP debe tener un collarín que proteja la

válvula del tanque.

Colocación correcta y espacio libre de la parrilla

Nunca use la parrilla de gas en un garaje, entrada, cobertizo,

corredor o cualquier otro lugar cerrado. La parrilla de gas debe

utilizarse sólo al aire libre, al menos 36 pulgadas desde la

parte de atrás y del costado de cualquier superficie combustible.

La parrilla de gas no debe utilizarse en una construcción

combustible elevada.

•No obstruya el flujo de aire de la ventilación que se encuentra en la

carcasa de la parrilla de gas.

• No instale esta parrilla de gas para exteriores en o sobre vehículos

recreativos o botes

• Mantenga despejada y sin materiales combustibles, gasolina y

demás vapores y líquidos inflamables el área donde se encuentra la

parrilla de gas para exteriores

• No obstruya el flujo de combustión y del aire de la ventilación.

Controle esto con anterioridad cada vez que use la parrilla.

• Nunca conecte un tanque de gas LP sin regular a la parrilla de gas.

El ensamble del regulador de gas que viene con su parrilla de gas

está adaptado para que tenga una presión de salida de una columna

de agua (W.C.) de 11” para la conexión a un tanque de gas LP.

• Sólo use el ensamble del regulador y la manguera que viene con su

parrilla de gas. Los ensambles de los reguladores y de la manguera

de reemplazo deben ser los que se especifican en este manual.

•Haga llenar su tanque de gas LP por un distribuidor de gas propano

de confianza, haga que le practiquen una inspección ocular y lo dejen

en condiciones cada vez que llene el tanque.

• No guarde un tanque de gas LP de repuesto debajo de o cerca de

este dispositivo.

• Nunca llene el tanque superando el 80 por ciento de la capacidad.

Si esta instrucción no se cumpliera con exactitud, es posible que se

produzca un incendio que ocasione la muerte o lesiones graves.

• Siempre mantenga los tanques de gas LP en una posición vertical.

• No almacene o use gasolina u otros vapores o líquidos inflamables

en las cercanías de esta parrilla de gas.

• No someta el tanque de gas LP a un calor excesivo.

• Nunca almacene en un ambiente cerrado un tanque de gas LP. Si

usted guarda su parrilla de gas en el garaje o en otro lugar cerrado,

siempre desconecte el tanque de gas LP en primer término y

guárdelo afuera en un lugar seguro.

• Coloque la tapa anti-polvo sobre la salida de la válvula del cilindro

siempre que el mismo no esté en uso. Instale sólo el tipo de tapa

anti-polvo sobre la salida de la válvula del cilindro que viene con la

mencionada válvula. Otros tipos de tapas o tapones pueden causar

fugas de propano.

Conserve siempre el cilindor de

propano líquido a 90º (vertical) para

proporcionar la eliminación del vapor

• Los tanques de gas LP deben guardarse en exteriores, en

áreas bien ventiladas y fuera del alcance de los niños.

No deben guardarse los tanques de gas LP desconectados en

viviendas, garajes o en cualquier otro tipo de lugar cerrado.

• Cuando su parrilla de gas no esté en uso, se debe cerrar el

paso de gas en el tanque de gas LP.

• El ensamble del regulador y la manguera deben

inspeccionarse con anterioridad cada vez que se use la parrilla.

En caso de que exista abrasión o desgaste excesivo o si la

manguera está cortada, se debe reemplazar antes de que se

utilice la parrilla nuevamente.

• Mantenga la manguera del regulador de gas alejada de

superficies calientes de la parrilla y que recolecten grasa. Evite

la torsión innecesaria de la manguera. Haga una inspección

visual de la manguera con anterioridad cada vez que use la

parrilla para detectar cortes, rajaduras, desgaste excesivo u

otros daños. Si la manguera pareciera estar dañada, no use la

parrilla de gas. Llame al 1-800-913-8999 para solicitar una

manguera de reemplazo.

• Nunca encienda su parrilla de gas con la tapa cerrada o antes

de controlar a fin de asegurarse si los tubos de los mecheros

están colocados por complete en los orificios de las válvulas de

gas.

• Nunca permita que los niños operen la parrilla.

ADVERTENCIA

Un fuerte olor a gas o un sonido siseante del gas indica un

problema grave respecto de la parrilla de gas o el tanque de

gas LP. En caso de que las siguientes instrucciones no se

cumplieran, ello podría dar como resultado un incendio o

una explosión que podría causar lesiones corporales

graves, la muerte o daños a la propiedad.

• Cierre el suministro de gas de la parrilla.

• Gire las perillas de control a la posición de apagado

(OFF).

• Apague cualquier tipo de llama con un extintor de

incendios adecuado.

• Abra la tapa de la parrilla.

• Aléjese del tanque de gas LP.

• No intente solucionar el problema usted mismo.

• Si el olor persiste o tiene un incendio que no puede

apagar, llame al departamento de bomberos de su área. No

llame cerca del tanque de gas LP ya que el teléfono es una

forma de dispositivo eléctrico y podría generar chispas que

den como resultado un incendio y/o una explosión.

NOTA: El flujo normal de gas que va por el ensamble del

regulador y la manguera puede causar un zumbido. Un volumen

bajo de ruido es perfectamente normal y no interferirá con la

operación de la parrilla. Si el zumbido es fuerte y excesivo, es

posible que deba purgar el aire de la línea de gas o reajustar el

dispositivo de flujo de gas en exceso del regulador. Este

procedimiento de purga debe hacerse cada vez que se conecte

un nuevo tanque de gas LP a la parrilla. Para obtener asistencia

con este procedimiento, consulte la página 24, del título “En caso

de que aún no se encienda la parrilla” o llame al Centro de

Información sobre Parrillas al 1-800-913-8999.

PRECAUCIÓN: Tenga cuidado con los

fogonazos

PRECAUCIÓN: Las arañas y los insectos pequeños pueden

ocasionalmente tejer telillas o hacer nidos en los tubos de

los mecheros de la parrilla durante el transporte o mientras

están en el depósito. Estas telillas pueden causar

obstrucciones en el flujo de gas que podrían hacer que se

quemen los tubos de los mecheros y áreas circundantes.

Este tipo de evento se lo conoce como “FOGONAZO” y

puede causar graves daños a la parrilla y generar

condiciones de operación riesgosas para el usuario.

Aunque el tubo de un mechero obstruido no es la única

causa para que se genere un "FOGONAZO", es la más

común.

A fin de minimizar las probabilidades de que ello ocurra,

usted debe limpiar los tubos de los mecheros antes de

armar la parrilla y luego por lo menos una vez al mes hacia

el final del verano o a principios del otoño que es cuando

las arañas tienen mayor actividad. Asimismo realice este

procedimiento de limpieza si usted no ha usado la parrilla

durante un tiempo prolongado.

Consulte la sección Limpieza de Tubos y Puertos de los

Mecheros en la página 24

Control de las llamas de los mecheros

Controle en forma visual las llamas de los mecheros antes de cada uso.

Las llamas debe tener el aspecto que se observa en la imagen. En caso

contrario, consulte la sección sobre limpieza de los tubos y puertos de

los mecheros en la página 24 de este manual.

Verificación para detectar fugas de gas LP

Nunca haga pruebas para detectar fugas con una llama. Antes de

usarla por primera vez, al comienzo de cada estación o cada vez

que se cambie el tanque de gas LP, debe verificar el dispositivo

para detectar fugas de gas.

1. Haga una solución de jabón suave en partes iguales (50% agua/

50% jabón).

2. Gire las perillas de control a la posición de apagado (OFF);

luego abra el paso de gas (ON) en el tanque de suministro.

Aplique la solución jabonosa con un cepillo limpio en todas las

conexiones de gas. Observe a continuación. Si aparecen

formaciones de burbujas en la solución, las conexiones no

están selladas apropiadamente. Verifique cada conexión y

ajústelas o repárelas según sea necesario.

4. Si tiene una fuga en la conexión de gas que no pueda reparar,

cierre el paso de gas (OFF) en el tanque de suministro,

desconecte la línea de combustible de la parrilla y llame al 1-

800-913-8999 o a su proveedor de servicios de gas para que lo

asista en la reparación.

5. Asimismo, aplique la solución jabonosa en las junturas del

tanque. Observe a continuación. Si aparecen formaciones de

burbujas, cierre el tanque (OFF) y no lo use ni lo mueva.

Contacte al proveedor especialista en gas LP o al departamento

de bomberos de su localidad para obtener asistenciafor

assistance.

Verificación para la detección de fugas en la conexión de gas

Verificación para la detección

de fugas en el tanque de gas

Encendido manual de la parrilla con un cerillo

1. Coloque un cerillo en la varilla de encendido manual.

2. Siga los pasos 1 a 5 del Procedimiento de Encendido

Básico.

3. Encienda el cerillo y extienda la varilla de encendido hasta

la superficie de la rejilla de cocción.

4. Gire la perilla de control que desee hasta la posición de

máximo para liberar la salida del gas. El mechero debe

encenderse de inmediato.

ADVERTENCIA

En caso de que ocurriera un “FOGONAZO” en o cerca de

los tubos de los mecheros, siga las siguientes

instrucciones. En caso de que estas instrucciones no se

cumplieran, ello podría dar como resultado un incendio o

una explosión que podría causar lesiones corporales

graves, la muerte o daños a la propiedad.

• Cierre el suministro de gas de la parrilla.

• Gire las perillas de control a la posición de apagado (OFF).

• Apague cualquier tipo de llama con un extintor de incendios

adecuado.

• Abra la tapa de la parrilla.

• Cuando la parrilla se haya enfriado, limpie los tubos del

mechero y los mecheros según las instrucciones de limpieza

que están en la página 24.

Si no se puede encender la parrilla

1. Verifique el suministro y las conexiones de gas para detectar

fugas. Verifique que la totalidad de las conexiones de cables sean

seguras.

2. Repita el procedimiento de encendido básico. Si todavía la

parrilla no funciona, apague la fuente de gas, gire las perillas de

control a la posición de apagado (OFF), y verifique lo siguiente:

• Alineación errónea de los tubos de los mecheros sobre los

orificios

Corrección: vuelva a posicionar los tubos de los mecheros sobre

los orificios.

• Orificio tapado

Corrección: quite los mecheros de la parrilla, con cuidado

levante cada uno de los mecheros y aléjelos del orificio de la

válvula de gas. Quite el orificio de la válvula de gas y con

gentileza destape cualquier obstrucción con un alambre delgado.

Luego vuelva a instalar todos los orificios, mecheros y

componentes de cocción.

3. Si sospecha de que existe una obstrucción en las válvulas de

los mecheros de la parrilla, llame para solicitar un servicio de

reparación al 1-800-913-8999.

4. Si todavía la parrilla no enciende, es posible que deba purgar el

aire de la línea de gas o reajustar el dispositivo de flujo de gas en

exceso del regulador. Nota: Este procedimiento debe hacerse

cada vez que se conecte un nuevo tanque de gas LP a la parrilla.

Para purgar el aire de la línea de gas y/o reajustar el

dispositivo de flujo de gas en exceso del regulador:

• Gire todas las perillas de control a la posición de apagado

(OFF).

• Cierre el paso del gas de la válvula del tanque.

• Desconecte el regulador del tanque de gas LP.

• Deje a la unidad reposar durante 5 minutos.

• Vuelva a conectar el regulador al tanque de gas LP.

• Abra la válvula del tanque lentamente hasta que esté abierta en

un nivel de 1/4 a ½.

• Abra la tapa de la parrilla.

• Presione y gire cualquiera de las perillas de control a la posición

de máximo (HIGH).

• Gire las perillas de control a la posición de máximo (HIGH)

hasta que todos los mecheros estén encendidos.

• Puede comenzar a usar la parrilla

5. Si se han realizado todas las operaciones de verificación y

corrección y aún tiene consultas sobre la operación de su parrilla

de gas, llame al Centro de Información sobre Parrillas al 1-800-

913-8999.

Sostenga la tuerca del acoplador

y el regulador como se muestra

para conectarlos debidamente

con la válvula del tanque.

El niple tiene que estar

centrado con la válvula

del tanque LP.

5. Sostenga el regulador e inserte el empalme en la válvula del

tanque LP. Apriete con la mano la tuerca del acoplador,

sosteniendo el regular verticalmente con respecto del tanque

para que no se trasrosque la conexión.

6. Gire la tuerca del acoplador en el sentido del reloj y apriete

hasta que tope por completo. El regulador sella la función de

cierre lento de la válvula del tanque LP, lo que produce cierta

resistencia. Se requiere un giro adicional de media vuelta o

tres cuartos de vuelta para realizar la conexión. Aprieta

exclusivamente a mano; no use herramientas.

NOTA:

Si no puede llevar a cabo la conexión, desconecte el

regulador y repita los pasos 5 y 6. Si aun así no puede

realizarla, no use este regulador. Llame 1-800-913-8999 para

pedir ayuda.

Felicitaciones

Su parrilla de gas Nexgrill ya está lista para usarse.

Antes de usarla por primera vez y al principio de cada

estación (y siempre que se haya cambiado el tanque de

gas LP):

1. Lea todas las instrucciones relativas a la seguridad, el

encendido y la operación del dispositivo.

2. Verifique los orificios de la válvula de gas, los tubos de

los mecheros y los puertos de los mecheros para detectar

todo tipo de obstrucciones.

3. Realice un control para detectar fugas de gas de acuerdo

con las instrucciones que se encuentran en la siguiente

página de este manual.

Importante

Antes de cocinar en su parrilla por primera vez, lave las

rejillas y plataformas de cocción con agua caliente y

jabonosa. Enjuáguelas y séquelas minuciosamente.

Colóqueles aceite para cocinar en forma regular. Luego de

que la cocción se termine, ponga la parrilla en la posición

de máximo (HIGH) durante 3 a 5 minutos para quemar el

exceso de grasa o los residuos de comida.

DESCONEXIÓN DEL CILINDRO DE PROPANO LÍQUIDO

Gire las válvulas del mechero de la parrilla a la posición de

apagado (OFF) y asegúrese de que la parrilla esté fría.

Gire la válvula del cilindro de propano líquido a la posición de

apagado (OFF) girando las mismas en sentido de las agujas del

reloj hasta que haga tope.

Desprenda el ensamble del regulador de presión de la válvula

del cilindro girando la arandela de acoplamiento rápido en

sentido contrario de las agujas del reloj.

Coloque la tapa para polvo sobre la salida de la válvula del

cilindro cuando el cilindro no se use. Instale sólo el tipo de tapa

para polvo en la salida de la válvula del cilindro que viene con

dicha válvula. Otros tipos de tapas o tapones pueden dar como

resultado fugas de propano.

La page charge ...

Nexgrill 720-0894F Manuel utilisateur

Marque: Nexgrill

Modèle: 720-0894F

Catégorie: Barbecues

Taper: Manuel utilisateur

Ce manuel convient également à

720-0925

Télécharger le PDF

rapport

dans d''autres langues

English: Nexgrill 720-0894F User manual
español: Nexgrill 720-0894F Manual de usuario

Nexgrill 720-0894F Manuel utilisateur

Ce manuel convient également à

Nexgrill 720-0894F Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents