Whirlpool WGD9400SB0 Le manuel du propriétaire

Marque: Whirlpool

Modèle: WGD9400SB0

Catégorie: Sèche-linge

Taper: Le manuel du propriétaire

Ce manuel convient également à

WGD9400ST0

ELECTRONIC

GASDRYER

In the U.S.A., for questions about features, operation/performance,

parts, accessories or service call:

1-800-253-1301

In Canada, for assistance, installation and service call: 1-800-807-6777

or visit our website at.,. www,whirlpool,com or www,whirlpool,ca

SECHEUSEAGAZ

ELECTRONIQUE

Pour assistance, installation ou service composez le :

1-800-807-6777

ou visitez notre site web L_,,.

www,whirlpool,oa

Table of Contents/Table des mati_res ......................... 2

W10110851A

TABLEOFCONTENTS

RYER SAFETY ................................................................................ 3

INSTALLATION INSTRUCTIONS .................................................. 5

Tools and Parts ............................................................................ 5

Options ......................................................................................... 5

Location Requirements ............................................................... 6

Electrical Requirements ............................................................... 8

Gas Supply Requirements ........................................................... 8

Venting Requirements .................................................................. 9

Plan Vent System ....................................................................... 11

Install Vent System ..................................................................... 12

Install Leveling Legs ................................................................... 12

Level Dryer ................................................................................. 12

Make Gas Connection ............................................................... 13

Connect Vent .............................................................................. 13

Complete Installation ................................................................. 13

DRYER USE .................................................................................. 14

Starting Your Dryer ..................................................................... 14

Stopping Your Dryer .................................................................. 15

Pausing or Restarting ................................................................. 15

Control Locked ........................................................................... 15

Drying and Cycle Tips ................................................................ 15

Status Lights .............................................................................. 16

Cycles ......................................................................................... 16

Additional Features .................................................................... 17

Changing Cycles, Options and Modifiers .................................. 18

Drying Rack Option .................................................................... 18

DRYER CARE .............................................................................. 19

Cleaning the Dryer Location ...................................................... 19

Cleaning the Lint Screen ............................................................ 19

Cleaning the Dryer Interior ......................................................... 20

Removing Accumulated Lint ...................................................... 20

Vacation and Moving Care ......................................................... 20

Changing the Drum Light ........................................................... 20

TROUBLESHOOTING .................................................................. 21

Dryer Operation .......................................................................... 21

Dryer Results .............................................................................. 21

ASSISTANCE OR SERVICE ......................................................... 23

WARRANTY .................................................................................. 24

TABLEDESMATIERES

SECURITI :!:DE LA SECHEUSE .................................................... 25

INSTRUCTIONS D'INSTALLATION ............................................. 26

Outillage et pieces ...................................................................... 26

Options ....................................................................................... 27

Exigences d'emplacement ......................................................... 28

Specifications electriques .......................................................... 30

Alimentation en gaz .................................................................... 30

Exigences concernant I'evacuation ........................................... 32

Planification du systeme d'evacuation ...................................... 33

Installation du systeme d'evacuation ......................................... 35

Installation des pieds de nivellement ......................................... 35

Mise h niveau de la secheuse .................................................... 35

Raccordement au gaz ................................................................ 35

Raccordement du conduit d'evacuation ................................... 36

Achever I'installation .................................................................. 36

UTILISATION DE LA SI:!:CHEUSE................................................ 37

Mise en marche de la secheuse ................................................ 37

ArrGt de la secheuse ................................................................... 38

Pause ou remise en marche ....................................................... 38

Control Locked (verrouillage des commandes) ......................... 39

Conseils pour le sechage et les programmes ........................... 39

Temoins lumineux ...................................................................... 39

Programmes ............................................................................... 40

Caracteristiques supplementaires ............................................. 41

Changement des programmes, options et modificateurs .........42

Option de grille de sechage ....................................................... 42

ENTRETIEN DE LA SI_CHEUSE ................................................. 43

Nettoyage de I'emplacement dela secheuse ............................ 43

Nettoyage du filtre a charpie ...................................................... 43

Nettoyage de I'interieur de la secheuse ..................................... 44

Retrait de la charpie accumulee ................................................ 44

Precautions a prendre pour les vacances et

avant un demenagement ........................................................... 44

Changement de I'ampoule d'eclairage du tambour .................. 44

DI!:PANNAGE ................................................................................. 45

Fonctionnement de la secheuse ................................................ 45

Resultats de la secheuse ........................................................... 45

ASSISTANCE OU SERVICE ......................................................... 47

GARANTI E ..................................................................................... 48

DRYERSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

i WARNING: For your safety, the information in this manual must be followed to minimize

the risk of fire or explosion, or to prevent property damage, personal injury, or death.

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this

or any other appliance.

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Clear the room, building, or area of all occupants.

• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency, or

the gas supplier.

In the State of Massachusetts, the following installation instructions apply:

[] Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by

the State of Massachusetts.

[] If using a ball valve, it shall be a T-handle type.

[] A flexible gas connector, when used, must not exceed 3 feet.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic precautions,

including the following:

[] Read all instructions before using the dryer.

[] Do not place items exposed to cooking oils in your dryer.

Items contaminated with cooking oils may contribute to

a chemical reaction that could cause a load to catch fire.

[] Do not dry articles that have been previously cleaned in,

washed in, soaked in, or spotted with gasoline, dry-

cleaning solvents, or other flammable or explosive

substances as they give off vapors that could ignite or

explode.

[] Do not allow children to play on or in the dryer. Close

supervision of children is necessary when the dryer is

used near children.

[] Before the dryer is removed from service or discarded,

remove the door to the drying compartment.

[] Do not reach into the dryer if the drum is moving.

[] Do not install or store the dryer where it will be exposed

to the weather.

[] Do not tamper with controls.

[] Do not repair or replace any part of the dryer or attempt

any servicing unless specifically recommended in this

Use and Care Guide or in published user-repair

instructions that you understand and have the skills to

carry out.

[] Do not use fabric softeners or products to eliminate static

unless recommended by the manufacturer of the fabric

softener or product.

[] Do not use heat to dry articles containing foam rubber or

similarly textured rubber-like materials.

[] Clean lint screen before or after each load.

[] Keep area around the exhaust opening and adjacent

surrounding areas free from the accumulation of lint, dust,

and dirt.

[] The interior of the dryer and exhaust vent should be

cleaned periodically by qualified service personnel.

[] See installation instructions for grounding requirements.

SAVE THESE INSTRUCTIONS

IMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas

Code, ANSi Z223.1/NFPA 54 or the Canadian Natural Gas and Propane installation Code, CSA B149.1.

The dryer must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National

Electrical Code, ANSI/NFPA 70 or Canadian Electrical Code, CSA C22.1.

INSTALLATIONINSTRUCTIONS

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

8" or 10" pipe wrench

8" or 10" adjustable

wrench (for gas

connections)

Flat-blade screwdriver

Adjustable wrench that

opens to 1" (2.5 cm) or

hex-head socket wrench

(for adjusting dryer feet)

v4" nut driver or socket

wrench

• Level

• Knife

• Vent clamps

• Pipe-joint compound

resistant to LP gas

• Caulking gun and

compound (for installing

new exhaust vent)

• Pliers

• Tape measure

Parts supplied

Remove parts packages from dryer drum. Check that all parts are

included.

• Parts package

4 Leveling legs

NOTE: Do not use leveling legs if installing the dryer on a

pedestal.

Parts needed

Check local codes and with gas supplier. Check existing gas

supply, electrical supply and venting. Read "Electrical

Requirements," "Gas Supply Requirements" and "Venting

Requirements" before purchasing parts.

• For close-clearance installations between 31.5" (80.01 cm)

and 37" (93.98 cm), see "Plan Vent System" section for

venting requirements.

I_- 37" --_1

(93.98 cm)

Mobile home installations require special parts (listed following)

that may be ordered by calling the dealer from whom you

purchased your dryer. For further information, please refer to the

"Assistance or Service" section of this manual.

• Mobile Home Installation Kit. Ask for Part Number 346764.

• Metal exhaust system hardware.

Pedestal

Are you placing the dryer on a pedestal? You have the option of

purchasing pedestals of different heights separately for this dryer.

You may select a 10" (25.4 cm) or 15.5" (39.4 cm) pedestal.

These pedestals will add to the total height of the dryer for a total

height of approximately 48" (121.9 cm) or 53.5" (135.9 cm),

respectively.

For a garage installation, you will need to place the 10" (25.4 cm)

pedestal at least 9" (22.9 cm) above the floor and the

15.5" (39.4 cm) pedestal at least 3.5" (8.9 cm) above the floor.

A B

A. 10" (25.4 cm) pedestal

B. 15.5" (39.4 cm) pedestal

The pedestals are available in several colors.

To order, call the dealer from whom you purchased your dryer or

refer to the "Assistance or Service" section of this manual.

Pedestal Color Part Number

Height

10" (25.4 cm) White WHP1000SC

10" (25.4 cm) Biscuit WHP1000ST

10" (25.4 cm) Diamond Dust WHP1000SU

(Silver)

10" (25.4 cm) Black Diamond WHP1000SB

15.5" (39.4 cm) White WHP1500SC

15.5" (39.4 cm) Biscuit WHP1500ST

15.5" (39.4 cm) Diamond Dust WHP1500SU

(Silver)

15.5" (39.4 cm) Black Diamond WHP1500SB

Stack Kit

Are you planning to stack your DUET_ washer and dryer? To do

so, you will need to purchase a Stack Kit.

To order, call the dealer from whom you purchased your dryer or

refer to the "Assistance or Service" section of this manual. Ask

for Part Number 8541503.

Door Reversal Kit

Are you planning to reverse the door swing direction on your

DUET®dryer? To do so, you will need to purchase a Door

Reversal Kit.

To order, call the dealer from whom you purchased your dryer or

refer to the "Assistance or Service" section of this manual. Ask

for Part Number 8579666.

Door Reversal and Stack Combination Kit

Are you planning to reverse the door swing direction on your

DUET®dryer and stack your DUET®washer and dryer? To do so,

you can purchase a Door Reversal and Stack Combination Kit.

To order, call the dealer from whom you purchased your dryer or

refer to the "Assistance or Service" section of this manual. Ask

for Part Number W10110889.

Backguard

If you are installing your DUET° washer and dryer and wish to

avoid having loose items fall behind your machines, you may

purchase a pair of washer/dryer backguards. These will reduce

the chance of items falling behind the machines during operation.

To order, call the dealer from whom you purchased your dryer or

refer to the "Assistance or Service" section of this manual. Ask

for Part Number 8558694 (White).

• For a garage installation, you will need to place the dryer at

least 18" (46 cm) above the floor. If using a pedestal, you will

need 18" (46 cm) to the bottom of the dryer.

Do not operate your dryer at temperatures below 45°F (7°C). At

lower temperatures, the dryer might not shut off at the end of an

automatic cycle. This can result in longer drying times.

The dryer must not be installed or stored in an area where it will

be exposed to water and/or weather.

Check code requirements. Some codes limit, or do not permit,

installation of the dryer in garages, closets, mobile homes or

sleeping quarters. Contact your local building inspector.

NOTE: No other fuel-burning appliance can be installed in the

same closet as a dryer.

Installation clearances

The location must be large enough to allow the dryer door to

open fully.

Dryer Dimensions

(130.81 cm)

38 ,,I

(96.52 cm)

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer,

Place dryer at least 18 inches (46 cm) above the floor

for a garage installation.

Failure to do so can result in death, explosion, or fire.

You will need

• A location that allows for proper exhaust installation. A gas

dryer must be exhausted to the outdoors. See "Venting

Requirements."

A grounded electrical outlet located within 2 ft (61 cm) of

either side of the dryer. See "Electrical Requirements."

A sturdy floor to support the total dryer weight of 200 Ibs

(90.7 kg). The combined weight of a companion appliance

should also be considered.

A level floor with a maximum slope of 1" (2.5 cm) under entire

dryer. If slope is greater than 1" (2.5 cm), install Extended

Dryer Feet Kit, Part Number 279810. Clothes may not tumble

properly, and automatic sensor cycles may not operate

correctly if dryer is not level.

'311/_''

{80 cm) 27"

"_/ _ (68.6crn)

*Most installations require a minimum 5" (12,7 cm) clearance

behind the dryer for the exhaust vent with elbow. See "Venting

Requirements."

Installation spacing for recessed area or closet installation

The following spacing dimensions are recommended for this

dryer. This dryer has been tested for spacing of 0" (0 cm)

clearance on the sides and rear. Recommended spacing should

be considered for the following reasons:

• Additional spacing should be considered for ease of

installation and servicing.

• Additional clearances might be required for wall, door and

floor moldings.

• Additional spacing should be considered on all sides of the

dryer to reduce noise transfer.

For closet installation, with a door, minimum ventilation

openings in the top and bottom of the door are required.

Louvered doors with equivalent ventilation openings are

acceptable.

• Companion appliance spacing should also be considered.

Custom undercounter installation - Dryer only

1"* _ _-_27"--}_ _ 1"*

2,5 cm) 68,6 cm 2.5 cm

*Required spacing

Closet installation - Dryer only

I1"*_ 31v2"_h"-I

(2.5cm) (80cm) (12.7cm)

A. Side view - closet or confined area

B. Closet door with vents

3"*

(7,6cm)

(7.6cm)

*Required spacing

**For side or bottom venting, O" (Ocm) spacing is allowed.

Recessed or closet installation - Dryer on pedestal

1..1I_- 31v_"-_15""1

1"-_ 1"_27"--_11<-1"

(2.5 cm) (68.6 cm) (2.5 cm) (2.5 cm) (80 cm) (12.7 cm)

A B

A.Recessedarea

B.Side view - closet or confined area

*Required spacing

**For side or bottom venting, 0" (0 cm) spacing is allowed.

Recommended installation spacing for cabinet

installation

• For cabinet installation, with a door,minimum ventilation

openings inthe top of the cabinet are required.

T'* (17.8cm)

T'* (17.8 crn)

5"** 31W' 1"* 1" 27" 1"

(12.7 cm) (80.0 cra) (2.5 cra)(2.5 cm)(68.6 cm) (2.5 cra)

I/ ;;.80ml

*Required spacing

**For side or bottom venting, O" (Ocm) spacing is allowed.

Recommended installation spacing for recessed or

closet installation, with stacked washer and dryer

The dimensions shown are for the recommended spacing.

48 in.2 *

(310crn2)

24 in? *

(155crn2)

•Required spacing

(12.7crn)

3"* (7.6 cm) .....................

3"* (7.6 cm) =

_ -_- 1"* (2.5crn)

6"*Zcrn)

76"

{193 cm)

_- (2.51cm)

w'f_\X

_--27"_,, _ _ I"

68.6 cm 2.5 cm

*Required spacing

Mobile home - Additional installation requirements

This dryer is suitable for mobile home installations. The

installation must conform to the Manufactured Home

Construction and Safety Standard, Title 24 CFR, Part 3280

(formerly the Federal Standard for Mobile Home Construction

and Safety, Title 24, HUD Part 280) or Standard CAN/CSA-Z240

MH.

Mobile home installations require:

• Metal exhaust system hardware, which is available for

purchase from your dealer.

• Mobile Home Installation Kit Part Number 346764. See "Tools

and Parts" section for ordering information.

Special provisions must be made in mobile homes to

introduce outside air into the dryer. The opening (such as a

nearby window) should be at least twice as large as the dryer

exhaust opening.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

120 Volt, 60 Hz., AC only, 15- or 20-amp fused electrical

supply is required. A time-delay fuse or circuit breaker is

recommended. It is also recommended that a separate circuit

serving only this dryer be provided.

GROUNDING INSTRUCTIONS

• For a grounded, cord-connected dryer:

This dryer must be grounded. In the event of malfunction or

breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current.

This dryer is equipped with a cord having an equipment-

grounding conductor and a grounding plug. The plug must

be plugged into an appropriate outlet that is properly

installed and grounded in accordance with all local codes

and ordinances.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or service representative

or personnel if you are in doubt as to whether the dryer is

properly grounded. Do not modify the plug provided with the

dryer: if it will not fit the outlet, have a proper outlet installed

by a qualified electrician.

SAVE THESE INSTRUCTIONS

Explosion Hazard

Use a new CSA international approved gas supply line.

install a shut=off valve.

Securely tighten all gas connections.

If connected to LP, have a qualified person make sure

gas pressure does not exceed 13" (33 cm) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

Gas Type

Natural gas:

This dryer is equipped for use with Natural gas. It is design-

certified by CSA International for LP (propane or butane) gases

with appropriate conversion.

• Your dryer must have the correct burner for the type of gas in

your home. Burner information is located on the rating plate

in the door well of your dryer. If this information does not

agree with the type of gas available, contact your dealer or

call the phone numbers referenced in the "Assistance or

Service" section of this manual.

LP gas conversion:

Conversion must be made by a qualified technician.

No attempt shall be made to convert the appliance from the gas

specified on the model/serial rating plate for use with a different

gas without consulting your gas company.

Gas supply line

• Must include 1/8"NPT minimum plugged tapping accessible

for test gauge connection, immediately upstream of the gas

connection to the dryer. See illustration.

1/2"IPS pipe is recommended.

%" approved aluminum or copper tubing is acceptable for

lengths under 20 ft (6.1 m) if local codes and gas supplier

permit.

If you are using Natural gas, do not use copper tubing.

Lengths over 20 ft (6.1 m) should use larger tubing and a

different size adapter fitting.

If your dryer has been converted to use LP gas, %" LP

compatible copper tubing can be used. If the total length of

the supply line is more than 20 ft (6.1 m), use larger pipe.

NOTE: Pipe-joint compounds that resist the action of LP gas

must be used. Do not use TEFLON _ttape.

• Must include a shutoff valve:

In the U.S.A.:

An individual manual shutoff valve must be installed within

six (6)feet (1.8 m) of the dryer in accordance with the National

Fuel Gas Code, ANSI Z223.1.

In Canada:

An individual manual shutoff valve must be installed in

accordance with the B149.1, Natural Gas and Propane

Installation Code. It is recommended that an individual

manual shutoff valve be installed within six (6) feet (1.8 m)

of the dryer.

The location should be easy to reach for opening and closing.

A C E

B D

A. %" flexible gas connector

B. %" pipe to flare adapter fitting

C. Vs"NPT minimum plugged tapping

D. Y/' NPT gas supply line

E. Gas shutoff valve

Gas supply connection requirements

• Use an elbow and a 3/8"flare x %" NPT adapter fitting

between the flexible gas connector and the dryer gas pipe, as

needed to avoid kinking.

• Use only pipe-joint compound. Do not use TEFLON _ tape.

• This dryer must be connected to the gas supply line with a

listed flexible gas connector that complies with the standard

for connectors for gas appliances, ANSI Z21.24 or CSA 6.10.

Burner input requirements

Elevations above 10,000 ft (3,048 m):

• When installed above 10,000 ft (3,048 m) a 4% reduction of

the burner Btu rating shown on the model/serial number plate

is required for each 1,000 ft (305 m) increase in elevation.

Gas supply pressure testing

• The dryer must be disconnected from the gas supply piping

system during pressure testing at pressures greater than

1/2psi.

Dryer gas pipe

• The gas pipe that comes out through the rear of your dryer

has a %" male pipe thread.

1½"

A (3.8cm)

A. Y2"NPT gas supply line

B. _" NPT dryer pipe

*NOTE: Ifthe dryer is mounted on a pedestal, the gas pipe height

must be an additional 10" (25.4 cm) or 15.5" (39.4 cm) from the

floor, depending on the pedestal model. For a garage

installation, the gas pipe height must be an additional

18" (46 cm) from the floor.

Fire Hazard

Use a heavy metal vent.

Do not use a plastic vent.

Do not use a metal foil vent.

Failure to follow these instructions can result in death

or fire.

WARNING: To reduce the risk of fire, this dryer MUST BE

EXHAUSTED OUTDOORS.

IMPORTANT: Observe all governing codes and ordinances.

The dryer exhaust must not be connected into any gas vent,

chimney, wall, ceiling or a concealed space of a building.

If using an existing vent system

• Clean lint from the entire length of the system and make sure

exhaust hood is not plugged with lint.

• Replace any plastic or metal foil vent with rigid or flexible

heavy metal vent.

• Review Vent system chart. Modify existing vent system if

necessary to achieve the best drying performance.

1-®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

If this is a new vent system

Vent material

• Use a heavy metal vent. Do not use plastic or metal foil vent.

• 4" (10.2 cm) heavy metal exhaust vent and clamps must be

used. DURASAFE TM venting products are recommended.

Exhaust

4" (10.2cm) heavymetal exhaust vent

DURASAFE TM vent products can be purchased from your

dealer or by calling Whirlpool Parts and Accessories. For

more information, see the "Assistance or Service" section of

this manual.

Rigid metal vent

• For best drying performance, rigid metal vents are

recommended.

• Rigid metal vent is recommended to avoid crushing and

kinking.

Flexible metal vent

• Flexible metal vents are acceptable only if accessible for

cleaning.

• Flexible metal vent must be fully extended and supported

when the dryer is in its final location.

• Remove excess flexible metal vent to avoid sagging and

kinking that may result in reduced airflow and poor

performance.

• Do not install flexible metal vent in enclosed walls, ceilings or

floors. •

Elbows

45° elbows provide better airflow than 90° elbows.

Good Better

Clamps

• Use clamps to seal all joints.

• Exhaust vent must not be connected or secured with screws

or other fastening devices that extend into the interior of the

duct. Do not use duct tape.

Clamp

Recommended hood styles are shown here.

_ (1J._"!rn)

(10.2 cm)

A. Louvered hood style

B.Box hood style

The angled hood style (shown here) is acceptable.

" _ 21/2 .'

(6.4 cm)

An exhaust hood should cap the vent to keep rodents and

insects from entering the home.

Exhaust hood must be at least 12" (30.5 cm) from the ground

or any object that may be in the path of the exhaust (such as

flowers, rocks or bushes, snow line, etc.).

Do not use an exhaust hood with a magnetic latch.

improper venting can cause moisture and lint to collect

indoors, which may result in:

[] Moisture damage to woodwork, furniture, paint, wallpaper,

carpets, etc.

[] Housecleaning problems and health problems.

Choose your exhaust installation type

Recommended exhaust installations

Typical installations vent the dryer from the rear of the dryer.

Other installations are possible.

A=--

............... F

...................................G

A. Standard rear offset exhaust installation

B. Left or right side exhaust installation

C. Bottom exhaust installation (not an option

with pedestal installations)

A. Dryer

B. Elbow

C. Wall

D. Exhaust hood

E. Clamps

F. Rigid metal or flexible metal vent

G. Vent length necessary to connect elbows

H. Exhaust outlet

Optional exhaust installations

This dryer can be converted to exhaust out the right side, left

side, or through the bottom. Contact your local dealer to have the

dryer converted.

Fire Hazard

Cover unused exhaust holes with one of the

following kits:

279818 (white)

279820 (black)

279925 (biscuit)

279989 (pewter)

280171 (diamond dust)

Contact your local dealer.

Failure to follow these instructions can result in death,

fire, electrical shock, or serious injury.

Alternate installations for close clearances

Venting systems come in many varieties. Select the type best for

your installation. Two close-clearance installations are shown.

Refer to the manufacturer's instructions.

) ,,,

\\,\ II \\, j

A B

A. Over-the-top installation (also available with one

offset elbow)

B. Periscope installation

NOTE: The following kits for close clearance alternate

installations are available for purchase. Please see the

"Assistance or Service" section of this manual to order.

• Over-the-Top Installation:

Part Number 4396028

• Periscope Installation For use with dryer vent to wall vent

mismatch):

Part Number 4396037 - 0" (0 cm) to 18" (45.72 cm)

mismatch

Part Number 4396011 - 18" (45.72 cm) to 29" (73.66 cm)

mismatch

Part Number 4396014 - 29" (73.66 cm) to 50" (127 cm)

mismatch

Special provisions for mobile home installations

The exhaust vent must be securely fastened to a noncombustible

portion of the mobile home structure and must not terminate

beneath the mobile home. Terminate the exhaust vent outside.

Determine vent path

• Select the route that will provide the straightest and most

direct path outdoors.

• Plan the installation to use the fewest number of elbows and

turns.

• When using elbows or making turns, allow as much room as

possible.

• Bend vent gradually to avoid kinking.

• Use the fewest 90 °turns possible.

Determine vent length and elbows needed for best

drying performance

• Use the following Vent system chart to determine type of vent

material and hood combinations acceptable to use.

NOTE: Do not use vent runs longer than those specified in

the Vent system chart. Exhaust systems longer than those

specified will:

• Shorten the life of the dryer.

• Reduce performance, resulting in longer drying times and

increased energy usage.

The Vent system chart provides venting requirements that will

help to achieve the best drying performance.

Vent system chart

NOTE: Side and bottom exhaust installations have a 90° turn

inside the dryer. To determine maximum exhaust length, add one

90° turn to the chart.

Number of Type of Box or Angled

90° turns vent Iouvered hoods

or elbows hoods

0 Rigid metal 64 ft (20 m) 58 ft (17.7 m)

Flexible metal 36 ft (11 m) 28 ft (8.5 m)

1 Rigid metal 54 ft (16.5 m) 48 ft (14.6 m)

Flexible metal 31 ft (9.4 m) 23 ft (7 m)

2 Rigid metal 44 ft (13.4 m) 38 ft (11.6 m)

Flexible metal 27 ft (8.2 m) 19 ft (5.8 m)

3 Rigid metal 35 ft (10.7 m) 29 ft (8.8 m)

Flexible metal 25 ft (7.6 m) 17 ft (5.2 m)

4 Rigid metal 27 ft (8.2 m) 21 ft (6.4 m)

Flexible metal 23 ft (7 m) 15 ft (4.6 m)

1. Install exhaust hood. Use caulking compound to seal exterior

wall opening around exhaust hood.

2. Connect vent to exhaust hood. Vent must fit inside exhaust

hood. Secure vent to exhaust hood with 4" (10.2 cm) clamp.

3. Run vent to dryer location. Use the straightest path possible.

See "Determine vent path" in "Plan Vent System." Avoid 90°

turns. Use clamps to seal all joints. Do not use duct tape,

screws or other fastening devices that extend into the interior

of the vent to secure vent.

Excessive Weight Hazard

Use two or more people to move and install dryer.

Failure to do so can result in back or other injury.

1. To protect the floor, use a large flat piece of cardboard from

the dryer carton. Place cardboard under the entire back edge

of the dryer.

2. Firmly grasp the body of the dryer. Gently lay the dryer on the

cardboard. See illustration.

3. Examine the leveling legs. Find the diamond marking.

4. Screw the legs into the leg holes by hand. Use a wrench to

finish turning the legs until the diamond marking is no longer

visible.

5. Place a carton corner post from dryer packaging under each

of the 2 dryer back corners. Stand the dryer up. Slide the

dryer on the corner posts until it is close to its final location.

Leave enough room to connect the exhaust vent or gas line.

For mobile home use

Gas dryers must be securely fastened to the floor at the time of

installation.

Mobile home installations require a Mobile Home Installation Kit.

For more information, please reference the service numbers in

the "Assistance or Service" section of this manual.

Check the levelness of the dryer. Check levelness first

side to side, then front to back.

If the dryer is not level, prop up the dryer using a wood block.

Use a wrench to adjust the legs up or down and check again for

levelness.

_yp _. "! '! _

Remove the red cap from the gas pipe.

Using a wrench to tighten, connect the gas supply to the

dryer. Use pipe-joint compound on the threads of all non-

flared male fittings. If flexible metal tubing is used, be sure

there are no kinks.

A............................._ _ ............................B

A. Flared male fitting

B. Non-flared male fitting

NOTE: For LP gas connections, you must use pipe-joint

compound resistant to the action of LP gas. Do not use

TEFLON °t tape.

A combination of pipe fittings must be used to connect the

dryer to the existing gas line. Shown is a recommended

connection. Your connection may be different, according to

the supply line type, size and location.

A. _" flexible gas connector

B. _" dryerpipe

C. _" to _" pipe elbow

D. _" pipe-to-flare adapter fitting

Open the shutoff valve in the supply line. The valve is open

when the handle is parallel to the gas pipe.

A. Closed valve

B.Open valve

Test all connections by brushing on an approved

noncorrosive leak-detection solution. Bubbles will show a

leak. Correct any leak found.

S'iSl a_.

: e

1. Check that a[[ parts are now installed. If there is an extra part,

go back through the steps to see which step was skipped.

2. Check that you have all of your tools.

3. Check the dryer's final location. Be sure the vent is not

crushed or kinked.

4. Check that the dryer is level. See "Level Dryer."

10.

11.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord,

Failure to follow these instructions can result in death,

fire, or electrical shock.

Plug into a grounded 3 prong outlet. Turn on power.

Remove any protective film or tape remaining on the dryer.

Dispose of/recycle all packaging materials.

Read "Dryer Use."

Wipe the dryer drum interior thoroughly with a damp cloth to

remove any dust.

Select a Timed Dry heated cycle, and start the dryer. Do not

select the Air Only Temperature setting.

If the dryer will not start, check the following:

• Dryer is plugged into a grounded 3 prong outlet.

• Electrical supply is connected.

• Household fuse is intact and tight, or circuit breaker has

not tripped.

• Dryer door is closed.

When the dryer has been running for 5 minutes, open the

dryer door and feel for heat. Ifyou feel heat, cancel cycle and

close door. If you do not feel heat, turn off the dryer and

check that the gas supply line shutoff valve is open.

• Ifthe gas supply line shutoff valve is closed, open it, then

repeat the 5-minute test as outlined above.

• Ifthe gas supply line shutoff valve is open, contact a

qualified technician.

1. Using a 4" (10.2 cm) clamp, connect vent to exhaust outlet in

dryer. If connecting to existing vent, make sure the vent is

clean. The dryer vent must fit over the dryer exhaust outlet

and inside the exhaust hood. Check that the vent is secured

to exhaust hood with a 4" (10.2 cm) clamp.

2. Move dryer into its final location. Do not crush or kink vent.

3. (On gas models) Check that there are no kinks in the flexible

gas line.

4. Once the exhaust vent connection is made, remove the

corner posts and cardboard.

1-®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

DRYERUSE

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Do not dry anything that has ever had anything

flammable on it (even after washing).

Failure to follow these instructions can result in death,

explosion, or fire.

Fire Hazard

No washer can completely remove oil.

Do not dry anything that has ever had any type of oil on

it (including cooking oils),

items containing foam, rubber, or plastic must be dried

on a clothesline or by using an Air Cycle.

Failure to follow these instructions can result in death

or fire.

This manual covers several different models. Your dryer may not

have all of the cycles and features described.

The following is a guide to starting your dryer. Please refer to

specific sections of this manual for more detailed information.

f. Clean lint screen before each load. See "Cleaning the Lint

Screen."

2. Place laundry in dryer and shut door.

3. Press the POWER button then rotate the dial to select either

an Automatic or Manual Cycle. The preset settings and drying

time for the cycle chosen will be displayed.

NOTE: A default time is displayed when an Automatic Cycle

is selected. During the first few minutes of the drying process,

the cycle time may automatically vary from the default time

based on the size and fabric type of the load. Toward the end

of the drying process, the estimated time display will adjust

again, showing the final drying time.

To use an Automatic Cycle

NOTE: A light next to each feature will glow green when the

feature is selected or will glow amber when the feature is

selectable. The light will not glow when the selection is

unavailable with the cycle or option combinations selected.

• Press the POWER button.

• Rotate the dial to select an Automatic Cycle.

Select DRYNESS LEVEL to adjust how dry you want the

load to be. As the cycle runs, the control senses the

dryness of the load and adjusts the time automatically for

the selected Dryness Level.

NOTE: Most loads may be dried using Normal, which is

shown in bold letters on your control panel. Normal is the

energy preferred dryness level and will use the least

energy.

Mo_e

Non//a(

ess

The default dryness setting is Normal when an Auto Dry

Cycle is selected. You can select a different dryness level,

depending on your load, by pressing DRYNESS LEVEL

and choosing More, Normal or Less. Selecting More,

Normal or Less automatically adjusts the dryness level at

which the dryer will shut off. Once a dryness level is set, it

cannot be changed without stopping the cycle.

The Dryness Level can be changed only with Automatic

Cycles.

Press the WRINKLE SHIELD TM feature button if this

option is desired.

Press the CYCLE SIGNAL button to set end of cycle

signal volume to desired level.

Press the DAMP DRY CYCLE SIGNAL button to set damp

dry signal volume to desired level.

• Press and hold START button until dryer starts (about

1 second).

Once an Automatic cycle has started, the WRINKLE

SHIELD TM feature and cycle signals can be adjusted. Press

the PAUSE/CANCEL key twice to stop the dryer and clear the

settings, allowing you to select another cycle and Dryness

Level.

NOTE: Time and Temperature are not adjustable for

Automatic Cycles. Pressing the DRY TIME or TEMPERATURE

buttons will cause a triple beep, indicating that the time

cannot be changed.

How Automatic Cycles Work

The AccelerCare TM function improves drying performance

with Auto Moisture Sensing Plus, which advances the cycle

as moisture is extracted from clothing. A thermistor

(electronic temperature sensor) and moisture sensing strips in

the dryer drum help measure the amount of moisture in the

clothes as they tumble. An electronic control determines the

load type to help save time, avoid overdrying, and increase

the accuracy of the end dryness level. After the first 5 minutes

of an automatic cycle, the estimated time display will adjust

based on the approximate load size, cycle, dryness level

selected and amount of moisture left in the clothes. When the

clothes have reached approximately 80% of the dryness level

selected, the estimated time display will adjust again,

showing the final drying time. The AccelerCare TM feature

takes the guesswork out of drying time and enhances fabric

care.

To use a Manual Cycle

NOTE: A light next to each feature will glow green when the

feature is selected or will glow amber when the feature is

selectable. The light will not glow when the selection is

unavailable with the cycle or option combinations selected.

• Press POWER.

Rotate the dial to select a Manual Cycle.

Press the DRY TIME up or down buttons until the desired

drying time is displayed. Press DRY TIME, and the time

will change by 1-minute intervals. Press and hold DRY

TIME, and the time will change by 5-minute intervals. The

initial time displayed is the actual drying time.

Adi_stManual

0ryTime

®®

The Dry Time feature can be used only with Manual

Cycles.

Press TEMPERATURE until the desired temperature

glows green.

I High

Medium

Low

ExtraLow

Air Only

Temperature

Adjst Manual

Cyde_Only

Temperature settings can be changed only with Manual

Cycles.

Press the WRINKLE SHIELD TM feature button if this

option is desired.

Press the CYCLE SIGNAL button to set end of cycle

signal volume to desired level.

• Press and hold START button until dryer starts (about

1 second).

NOTE: Dryness Level is not adjustable for Manual Cycles.

Pressing the Dryness Level button will cause the triple beep

indicating that this option is not selectable.

While a Manual Cycle is running, you can change the settings

for Time, Temperature, the WRINKLE SHIELD TM feature and

the cycle signals. Press the PAUSE/CANCEL key twice to

stop the dryer and clear the settings, allowing you to select

another cycle.

To stop your dryer at anytime

Press PAUSE/CANCELtwice or open the door.

To pause the dryer at any time

Open the door or press PAUSE/CANCEL once.

To restart the dryer

Close the door and press and hold START button until dryer

starts.

NOTE: Drying will continue from where the cycle was interrupted,

if you close the door and press Start within 5 minutes. If the cycle

is interrupted for more than 5 minutes, the dryer will shut off.

Select new cycle settings before restarting the dryer.

This feature allows you to lock your settings to avoid unintended

use of the dryer. You can also use the Control Locked feature to

avoid unintended cycle or option changes during dryer operation.

To enable the Control Locked feature when dryer is

running:

Press and hold the CONTROL LOCK/UNLOCK button for

3 seconds. The control is locked when a single beep is heard and

the Control Locked status light is on.

• When the dryer is off, it is not necessary to press the Control

On button before activating the Control Locked feature.

To unlock:

Press and hold the CONTROL LOCK/UNLOCK button for

3 seconds to turn this feature off.

NOTE: When the dryer is running and Control Locked is on, the

dryer can be stopped by pressing the Pause/Cancel button, but

cannot be restarted until the control is unlocked.

Select the correct cycle and dryness level or temperature for your

load. If an Automatic Cycle is running, the display shows the

estimated cycle time when your dryer is automatically sensing

the dryness level of your load. If a Manual Cycle is running, the

display shows the exact number of minutes remaining in the

cycle.

Cool Down tumbles the load without heat during the last few

minutes of all cycles. Cool Down makes the loads easier to

handle and reduces wrinkling. The length of the Cool Down

depends on the load size and dryness level.

Drying tips

• Follow care label directions when they are available.

• If desired, add a fabric softener sheet. Follow package

instructions.

• Remove the load from the dryer as soon as tumbling stops to

reduce wrinkling. This is especially important for permanent

press, knits and synthetic fabrics.

Avoid drying heavy work clothes with lighter fabrics. This

could cause overdrying of lighter fabrics, leading to increased

shrinking or wrinkling.

If you dry sheets in a mixed load or large items in the Bulky

Items cycle, rearrange the load when the signal sounds. This

will aid in the drying process.

Indicator lights

Other indicator lights on the control panel show Cycle,

Temperature, Dryness Level, and cycle signal settings selected.

The time display will indicate the estimated or actual time

remaining in a cycle.

Cycle tips

• Dry most loads using the preset cycle settings.

• Refer to the Automatic or Manual Preset Cycle Settings chart

(in the "Cycles" section) for a guide to drying various loads.

Drying temperature and Dryness Level are preset when

you choose an Automatic Cycle. You can choose a

different dryness level, depending on your load by

pressing the DRYNESS LEVEL button to select MORE,

NORMAL or LESS.

• Ifyou wish to adjust the cycle length of a Manual Cycle,

you must press the DRY TIME up or down buttons. Adjust

the temperature of a Manual Cycle by pressing

TEMPERATURE until the desired temperature is selected.

NOTE: You cannot choose a Dryness Level with Manual

Cycles.

Select the drying cycle that matches the type of load you are

drying. See Automatic Preset or Manual Preset Cycle Settings

chart.

NORMAL

CASUAL BULKYITEMS

DELICATE HEAVYDUTY

SUPER

DELICATE

DAMPDRY

AUTOMATICCYCL[S [viANUALCYCLES

TIMEDDRY

TOUCHUP

_UICKDRY

You may follow the progress of your dryer with the drying Status

indicator lights.

WrinkleShield Sensing

Wet Damp C001D0wnDone

WRINKLE SHIELD TM Feature

The WRINKLE SHIELD TM feature light glows during the WRINKLE

SHIELD TM feature (when selected).

Sensing

When a cycle is first turned on, the Sensing light glows until a wet

item is detected.

• In an Automatic Cycle, if a wet item has not been detected

within 10 minutes, the Sensing light will turn off and the dryer

will shut down.

• In a Manual Cycle, if a wet item is not detected after

10 minutes, the Wet light turns on and the selected cycle

continues.

Cycle Control knob

Automatic Cycles

Automatic Cycles allow you to match the cycle to the load you

are drying. See the following Automatic Preset Cycle Settings

chart. Each cycle dries certain fabrics at the recommended

temperature. A sensor detects the moisture in the load and

automatically adjusts the drying time for optimal drying.

Heavy Duty

Use this cycle to get High heat for heavyweight mixed loads,

cotton towels or jeans.

Bulky Items

Use this cycle to get Medium heat for drying large items that

require very long drying times such as jackets, comforters and

pillows. Rearrange the load halfway through the dryer cycle. This

will aid in the drying process.

Normal

Use this cycle to get Medium heat for drying sturdy fabrics such

as work clothes and sheets.

Wet

The Wet light will turn on when a wet item has been detected in

the dryer. The Wet light will remain on until:

• The damp dry point is reached in an Automatic Cycle.

• The dryer enters the cool down period in a Manual Cycle.

Damp

The Damp light indicates that the load has reached the damp dry

level. To be alerted when your load is approximately 80% dry, you

may use the Damp Dry Cycle Signal option. See "Damp Dry

Cycle Signal" in "Additional Features" section.

NOTE: The Damp light is not used with manual cycles.

Cool Down

The Cool Down light glows during the cool down part of the

cycle. Laundry is cooling down for ease in handling.

Done

The Done light illuminates when the drying cycle is finished. This

indicator stays on during the WRINKLE SHIELD TM feature.

Casual

Use this cycle to get Low heat for drying no-iron fabrics such as

sport shirts, casual business clothes and permanent press

blends.

Delicate

Use this cycle to get Low heat to gently dry items such as

washable knit fabrics.

Super Delicate

Use this cycle to get Extra-Low heat to gently dry items such as

lingerie.

Damp Dry

Use this cycle to dry items to a damp level using Low heat. Damp

dry items such as jeans (to avoid stiffness) or cotton clothing (to

make ironing easier). The temperature setting on this cycle

cannot be adjusted. Items will have different levels of dampness.

At the end of this cycle, clothes will be damp. To be alerted when

this cycle is complete, select the End of Cycle Signal.

Automatic Preset Cycle Settings

Automatic Cycles Temperature Time*

Load Type (Minutes)

HEAVY DUTY High 50

Heavyweight items, towels, jeans

BULKY ITEMS Medium 55

Jackets, comforters, pillows

NORMAL Medium 40

Corduroys, work clothes, sheets

CASUAL Low 35

Permanent press, synthetics

DELICATE Low 30

Lingerie, blouses, washable

woolens

SUPER DELICATE Extra Low 25

Lingerie, blouses, washable

Woolens

DAMP DRY Low 20

Clothes to come out suitable for

ironing

*Estimated Time with Dryness Level (medium) setting. Time will

vary depending on load type and load size.

Manual Cycles

Use Manual Cycles to select a specific amount of drying time and

a drying temperature. When a Manual Cycle is selected, the

Estimated Time Remaining display shows the actual time

remaining in your cycle. You can change the actual time in the

cycle by pressing the DRY TIME up or down buttons.

Timed Dry

Use this cycle to complete drying if items are still damp after an

Automatic Cycle. Timed Dry is also useful for drying heavyweight

and bulky items such as bedspreads and work clothes.

Lightweight garments, such as exercise wear, can be dried using

Timed Dry on a Low temperature setting.

Touch Up

Use this setting to help smooth out wrinkles from such items as

clothes packed in a suitcase or wrinkled from being left in the

dryer too long.

Quick Dry

Use this cycle for drying small loads or loads that need a short

drying time.

Manual Preset Cycle Settings

Manual Cycles Temperature Default Time

Load Type (Minutes)

TIMED DRY High 40

Heavyweight items, bulky

items, bedspreads, work

clothes

TOUCH UP Medium 15

Helps to smooth out

wrinkles

QUICK DRY High 21

Small loads

Air Only

Use the Air Only setting for items that require drying without heat

such as rubber, plastic and heat-sensitive fabrics. This chart

shows examples of items that can be dried using Air Only.

Type of Load Time*

(Minutes)

Foam rubber - pillows, padded bras, stuffed toys 20 - 30

Plastic - Shower curtains, tablecloths 20 - 30

Rubber-backed rugs 40 - 50

Olefin, polypropylene, sheer nylon 10 - 20

*Reset time to complete drying, if needed.

When using Air Only

• Check that coverings are securely stitched.

• Shake and fluff pillows by hand periodically during the cycle.

• Dry item completely. Foam rubber pillows are slow to dry.

NOTE: Automatic Cycles are not available when using the Air

Only setting.

Drum Light

Select Drum Light to turn on the light inside the dryer drum.

During a cycle, if Drum Light is selected, the drum light turns on

and will remain on until DRUM LIGHT is pressed again, the door

is open and closed, or the door is left open for 20 minutes.

When the dryer is not running, the drum light will turn on when

DRUM LIGHT is pressed or the dryer door is opened, and it will

remain on until the dryer door has been open for 20 minutes, the

dryer door is closed or DRUM LIGHT is pressed again.

Press DRUM LIGHT at any time to turn the drum light ON or OFE

WRINKLE SHIELD TM Feature

When you are unable to remove a load of clothes from the dryer

as soon as it stops, wrinkles can form. The WRINKLE SHIELD TM

feature periodically tumbles, rearranges and fluffs the load to help

keep wrinkles from forming.

• Press the WRINKLE SHIELD TM feature to get up to

120 minutes of heat-free, periodic tumbling at the end of a

cycle.

• Stop at any time by pressing the WRINKLE SHIELD TM feature

or opening the dryer door.

For the Casual Cycle, the WRINKLE SHIELD TM feature is

preset to "ON." The other cycles will retain the WRINKLE

SHIELD TM feature setting. (For example, if you select the

WRINKLE SHIELD TM feature in the Normal cycle, the

WRINKLE SHIELD TM feature will be on the next time you

select the Normal cycle.)

NOTE: If you do not select the WRINKLE SHIELD TM feature, the

dryer stops after the cool down period.

Damp Dry Cycle Signal

On some models, the Damp Dry Signal may be selected to alert

you that your clothes are approximately 80% dry. This is useful

when you want to remove lightweight items in a mixed load to

avoid overdrying or remove partially dry items that may need

ironing.

The DAMP DRY SIGNAL is useful when drying bedsheets/linens

in a mixed load. When the signal goes off, open the door to stop

the dryer, rearrange the load inside the dryer, close the door and

restart the dryer to finish the drying cycle. Rearranging the load

will aid in the drying process.

[0_d

Soft

Off

Press DAMP DRY CYCLE SIGNAL until the desired volume

(Loud, Soft or Off) glows green.

NOTE: This signal is independent of the Damp Dry Cycle. The

Damp Dry Signal is available only with the Automatic Cycles.

Cycle Signal

The End of Cycle Signal produces an audible sound when the

drying cycle is finished. Promptly removing clothes at the end of

the cycle reduces wrinkling.

Loud

Soft

Off

Cycle

Signal

Press CYCLE SIGNAL until the desired volume (Loud, Soft or Off)

glows green.

NOTE: When the WRINKLE SHIELD TM feature is selected and the

End of Cycle Signal is on, an audible sound will be emitted every

5 minutes until the clothes are removed, or the WRINKLE

SHIELD TM feature is finished.

Button Sound

You can change the volume of the sound of the beeps. Press

BUTTON SOUND until the desired volume (Loud, Soft or Off)

glows green. The Power and Cancel buttons will still beep softly

even when the Button Sound volume is set to Off.

Loud

Soft

Off

Button

Sound

Changing Modifiers and Options after pressing Start

You can change a Modifier or Option anytime before the selected

Modifier or Option begins.

1. Press PAUSE/CANCEL once.

2. Select the new Modifier and/or Option.

3. Press and hold START to continue the cycle.

NOTE: If you happen to press Pause/Cancel twice, the program

clears and your dryer shuts down. Restart the selection process.

Changing the Preset Dryness Level Settings

If all your loads on all Auto Dry cycles are consistently not as dry

as you would like, you may change the preset Dryness Level

settings to increase the dryness. This change will affect all of your

Auto Dry cycles.

Your Dryness Level settings can be adjusted to adapt to different

installations, environmental conditions or personal preference.

There are 3 drying settings: 1 (factory preset dryness level),

2 (slightly dryer clothes, approximately 15% more drying time)

and 3 (much dryer clothes, approximately 30% more drying

time).

1. The Dryness Level settings cannot be changed while the

dryer is running.

2. Press and hold the Dryness Level button for 5 seconds. The

dryer will beep, and "CF" will be displayed for 1 second

followed by the current drying setting.

3. To select a new drying setting, press the Dryness Level key

again until the desired drying setting is shown.

NOTE: While cycling through the settings, the current setting

will not flash, but the other settings will flash.

4. Press START to save the drying setting.

5. The drying setting you selected will become your new preset

drying setting for all Auto Dry cycles.

The drying rack is useful for drying items you would not

necessarily want to tumble dry or that you would normally line dry

(for example, sweaters).

If your model does not have a drying rack, you may be able to

purchase one for your model. To find out whether your model

allows drying rack usage and for information on ordering, please

refer to the front page of the manual or contact the dealer from

whom you purchased your dryer.

To use the drying rack

Do not remove the lint screen.

1. Open dryer door.

You can change Auto Cycles, Timed Cycles, Modifiers and

Options anytime before pressing Start.

• Three short tones sound if an unavailable combination is

selected. The last selection will not be accepted.

Changing Cycles after pressing Start

1. Press PAUSE/CANCEL twice. This ends the current cycle.

2. Select the desired cycle and options.

3. Press and hold START.The dryer starts at the beginning of

the new cycle.

NOTE: If you do not press Start within 5 minutes of selecting the

cycle, the dryer automatically shuts off.

A. Front edge

Place drying rack inside dryer drum, positioning the back wire

on the ledge of the inner dryer back panel. Push down on

front edge of drying rack to secure over the lint screen.

A. Dryerrack front edge

B.Dryerback panel

3. Put the wet items on top of the rack. Leave space between

the items so air can reach all the surfaces.

NOTE: Do not allow items to hang over the edge of the rack.

Close the door.

Select a timed drying cycle and temperature, or an air cycle

(see following chart). Items containing foam, rubber, or plastic

must be dried on a clothesline or by using the Air Only

temperature setting.

6. You must select a time by pressing the DRY TIME up or down

buttons. Reset time as needed to complete drying. Refer to

the following table.

7. Press and hold START button (about 1 second).

NOTE: Check the lint screen and remove any lint accumulated

from items dried on the rack.

This chart shows examples of items that can be rack dried and

the suggested cycle, temperature setting and drying time. Actual

drying time will depend on the amount of moisture items hold.

Rack Dry Setting Temp. Time*

Wool Sweaters Timed Low 60

Block to shape and lay flat on Dry

the rack.

Stuffed toys or pillows Timed Low 60

Cotton or polyester fiber filled Dry

Stuffed toys or pillows N/A Air Only 90

Foam rubber filled (no heat)

Sneakers or canvas shoes N/A Air Only 90

(no heat)

*(Minutes) Reset time to complete drying, if needed.

NOTE: You must remove rack for normal tumbling. Do not use

automatic cycles with the drying rack.

DRYERCARE

Keep dryer area clear and free from items that would obstruct the

flow of combustion and ventilation air.

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Place dryer at least 18 inches (46 cm) above the floor

for a garage installation.

Failure to do so can result in death, explosion, or fire.

Every load cleaning

The lint screen is located in the door opening of the dryer. The

control panel has an indicator light to remind you to clean the lint

screen before or after each load. A screen blocked by lint can

increase drying time.

To clean

1. Pull the lint screen straight up. Roll lint off the screen with

your fingers. Do not rinse or wash screen to remove lint. Wet

lint is hard to remove.

2. Push the lint screen firmly back into place.

IMPORTANT:

• Do not run the dryer with the lint screen loose, damaged,

blocked, or missing. Doing so can cause overheating and

damage to both the dryer and fabrics.

• If lint falls off the screen into the dryer during removal, check

the exhaust hood and remove the lint. See "Venting

Requirements."

As needed cleaning

Laundry detergent and fabric softener residue can build up on the

lint screen. This buildup can cause longer drying times for your

clothes, or cause the dryer to stop before your load is completely

dry. The screen is probably clogged if lint falls off the screen.

Clean the lint screen with a nylon brush every 6 months, or more

frequently, if it becomes clogged due to a residue buildup.

To wash

1. Roll lint off the screen with your fingers.

2. Wet both sides of lint screen with hot water.

3. Wet a nylon brush with hot water and liquid detergent. Scrub

lint screen with the brush to remove residue buildup.

4. Rinse screen with hot water.

5. Thoroughly dry lint screen with a clean towel. Replace screen

in dryer.

To clean dryer drum

1. Make a paste with powdered laundry detergent and very

warm water.

2. Apply paste to a soft cloth.

Apply a liquid, nonflammable household cleaner to the

stained area and rub with a soft cloth until all excess dye and

stains are removed.

3. Wipe drum thoroughly with a damp cloth.

4. Tumble a load of clean cloths or towels to dry drum.

NOTE: Garments that contain unstable dyes, such as denim blue

jeans or brightly colored cotton items, may discolor the dryer

interior. These stains are not harmful to your dryer and will not

stain future loads of clothes. Dry unstable dye items inside out to

avoid dye transfer.

Moving care

1. Unplug the power supply cord.

2. Close shutoff valve in gas supply line.

3. Disconnect gas supply line pipe and remove fittings attached

to dryer pipe.

4. Cap the open fuel supply line.

5. Make sure leveling legs are secure in dryer base.

6. Use masking tape to secure dryer door.

The dryer light automatically turns on inside the dryer drum when

you open the door.

To change the drum light

1. Unplug dryer or disconnect power.

2. Open the dryer door. Locate the light bulb cover on the back

wall of the dryer. Remove the screw located in the lower right

corner of the cover. Remove the cover.

From Inside the Dryer Cabinet

Lint should be removed every 2 years, or more often, depending

on dryer usage. Cleaning should be done by a qualified person.

From the Exhaust Vent

Lint should be removed every 2 years, or more often, depending

on dryer usage.

Vacation care

Operate your dryer only when you are at home. If you will be on

vacation or not using your dryer for an extended period of time,

you should:

1. Unplug dryer or disconnect power.

2. Close shutoff valve in gas supply line.

3. Clean lint screen. See "Cleaning the Lint Screen."

3. Turn bulb counterclockwise. Replace the bulb with a 10-watt

appliance bulb only. Replace the cover and secure with the

screw.

4. Plug in dryer or reconnect power.

La page charge ...

Whirlpool WGD9400SB0 Le manuel du propriétaire

Marque: Whirlpool

Modèle: WGD9400SB0

Catégorie: Sèche-linge

Taper: Le manuel du propriétaire

Ce manuel convient également à

WGD9400ST0

Télécharger le PDF

rapport

dans d''autres langues

English: Whirlpool WGD9400SB0 Owner's manual

Whirlpool WGD9400SB0 Le manuel du propriétaire

Ce manuel convient également à

Whirlpool WGD9400SB0 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents