MicroTouch OF-150P-A1 Manuel utilisateur

OF-150P-A1

Open Frame Touch Monitor

User Manual

Version 2.0 2021/03

1

About This Document

No part of this publication may be reproduced, transmitted, transcribed, stored in a

retrieval system, or translated into any language or computer language, in any form or

by any means, including, but not limited to, electronic, magnetic, optical, chemical,

manual, or otherwise without prior written permission of MicroTouchTM a TES Company.

The information in this document is subject to change without notice. MicroTouchTM a

TES Company makes no representations or warranties with respect to the contents

herein, and specifically disclaims any implied warranties of merchantability or fitness for

a particular purpose. MicroTouchTM a TES Company reserves the right to revise this

publication and to make changes from time to time in the content hereof without

obligation of MicroTouchTM a TES Company to notify any person of such revisions or

changes. Windows is a registered trademark of Microsoft, Inc. Other brand or product

names are trademarks of their respective holders.

2

Compliance Information

For FCC (USA)

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy, and if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) this device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

For IC (Canada)

CAN ICES-3(B)/NMB-3(B)

For CE (EU)

The device complies with the EMC Directive 2014/30/EU and Low Voltage Directive

2014/35/EU

3

Renseignements relatifs à la conformité

Pour la FCC (États-Unis).

Ce matériel a fait l’objet d’essais qui ont déterminé qu’il respectait les limites d’un appareil

de classe B selon la partie 15 des règlements de la FCC. Ces limites sont établies pour

assurer une protection raisonnable contre les parasites nuisant à une installation

résidentielle. Ce matériel génère, utilise et peut émettre des ondes radio électriques, et

lorsqu’il n’est pas installé et utilisé selon les instructions, peut causer des parasites

nuisant aux communications radio. Il n’y a toutefois aucune garantie qu’il n’y aura pas de

parasites dans une installation en particulier. Si ce matériel cause des parasites à la

réception d’ondes radio ou de télévision, ce qui peut être déterminé en l’éteignant et en

l’allumant, l’utilisateur est invité à essayer de corriger le problème des parasites par l’une

ou l’autre des mesures suivantes :

• Réorienter ou déplacer l’antenne de réception.

• Augmenter la distance entre le matériel et la réception.

• Brancher le matériel dans une prise sur un autre circuit que celui où le récepteur est

branché.

• Consulter le distributeur ou un technicien radio ou TV expérimenté pour des conseils.

L’appareil respecte la partie 15 des règlements de la FCC. Le fonctionnement doit

respecter les deux conditions suivantes : 1) cet appareil ne doit pas causer de parasites et

(2) cet appareil doit accepter tous les parasites reçus, notamment ceux pouvant causer un

fonctionnement non voulu.

Pour Industrie Canada

Norme canadienne NMB-3(B)

Pour la CE (UE)

L’appareil respecte la directive 2014/30/UE relative à la compatibilité électromagnétique et

la directive 2014/35/EU sur les limites de basse tension

4

Usage Notice

Precautions

Please follow all warnings, precautions and maintenance as recommended in this user’s

manual to maximize the life of your unit.

Do

：

▪ Turn off the product before cleaning.

▪ Use a soft cloth moistened with mild detergent to clean the product housing.

▪ Use only the qualified power adapter that comes with your device.

▪ Disconnect the power plug from AC outlet if the product is not going to be used for an

extended period of time.

Don’t

：

▪ Do not use abrasive cleaners, waxes or solvents for your cleaning.

▪ Do not operate the product under the following conditions:

- Extremely hot, cold or humid environment.

- Areas susceptible to excessive dust and dirt.

- Near any appliance generating a strong magnetic field.

! Warning - To prevent the risk of fire or shock hazards, and do not

expose the product to moisture.

! Warning - Please do not open or disassemble the product as this may

cause electric shock.

! Warning - Power cord shall be connected to a socket-outlet with

earthing connection.

! Warning - The cable cover cannot be removed under normal use

conditions.

! Warning - Stability Hazard. The touch monitor may fall, causing

serious personal injury or death. To prevent injury, this

touch monitor must be securely attached to the wall in

accordance with the installation instructions.

5

Avis d’utilisation

Précautions

Veuillez suivre toutes les mises en garde, précautions et entretiens recommandés dans

ce manuel d’utilisation pour maximiser la durée de vie de votre unité.

À faire :

▪ Éteindre l’appareil avant de le nettoyer.

▪ Utiliser un chiffon humidifié par une solution savonneuse pour nettoyer le boîtier du

produit.

▪ Utiliser uniquement l’adaptateur d’alimentation prescrit pour votre appareil.

▪ Débrancher l’appareil lorsqu’il n’est pas utilisé pendant une période prolongée.

À éviter :

▪ Ne pas utiliser de nettoyants abrasifs, de cires ou de solvants pour le nettoyage

▪ Ne jamais utiliser l’appareil dans les conditions suivantes :

– des conditions environnementales extrêmes (chaud, froid ou humidité)

– des endroits remplis de poussières et de saletés.

– à proximité d’appareils produisant un fort champ magnétique.

! Mise en garde — Pour prévenir les risques d’incendie ou

d’électrocution, ne pas exposer le produit à l’humidité.

! Mise en garde — Prière de ne pas ouvrir ou démonter le produit, car

cela pourrait entraîner l’électrocution.

! Mise en garde – Le cordon d’alimentation doit être branché à une

prise pourvue d’une mise à la terre.

! Mise en garde – La gaine du câble ne doit pas être retirée en

conditions normales d’utilisation.

! Mise en garde — Risque de renversement. Le moniteur tactile peut se

renverser et causer de graves blessures corporelles, voire la mort.

Pour prévenir les blessures, ce moniteur tactile doit être solidement

fixé au mur selon les instructions d’installation.

 
   
Table of Contents 
 
Chapter 1 ........................................................................................................................ 7 
1 Overview .................................................................................................................... 8 
2 Feature ...................................................................................................................... 8 
3 Specifications ............................................................................................................. 8 
4 Block Diagram............................................................................................................ 9 
5 Interface Connectors ................................................................................................ 10 
5.1 Power Connector ............................................................................................. 10 
5.2 Video Signal Connector ................................................................................... 10 
6 Package Overview ................................................................................................... 12 
Chapter 2 ...................................................................................................................... 13 
1 About VESA Mount .................................................................................................. 14 
2 About Wall Mount ..................................................................................................... 16 
2.1 Attaching the side Brackets .............................................................................. 16 
2.2 Customer panel material .................................................................................. 17 
3 On-Screen Display ................................................................................................... 18 
3.1 OSD Function Description ................................................................................ 20 
3.2 Timing Table Chart ........................................................................................... 21 
3.3 EDID Data ........................................................................................................ 21 
4 Dimension ................................................................................................................ 22 
4.1 Front View ........................................................................................................ 22 
4.2 Side View ......................................................................................................... 22 
4.3 Rear View ........................................................................................................ 23 
Appendix ...................................................................................................................... 24 
 
 

7

Chapter 1

Product Introduction

8

1.1 Overview

The OF-150P-A1 series is developed for finance industry or hospitality. The OF-150P-A1

is a 15 inches touch display which uses the last touch technology.

1.2 Feature

▪ Support 75mm VESA mount

▪ 1024 x 768 resolution

▪ Touch type: Projected Capacitive

▪ Touch point: 10 points

1.3 Specifications

LCD Touch Panel

Size

15” TFT LCD

Brightness

215 cd/m2 (P-CAP)

Number of Pixels

1024 (H) × 768 (V)

Touch Type

P-CAP/ 10 points

Environment

Certificate

UL/cUL、CE、FCC

Compliance

IP65 Front Bezel

Operating Temperature

0C ~ 40C

Storage Temperature

-20C ~ 60C

Operating Humidity

20% ~ 80% RH, non-condensing

Mounting

VESA 75 mm x 75 mm

Dimension (W x H x D)

356.9 mm x 280.9 mm x 52.3 mm

Net Weight

3.27 kg

Gross Weight

5.28 kg

9

1.4 Block Diagram

10

1.5 Interface Connectors

1.5.1 Power Connector

The AC/DC converter shall have an IEC320 type male power receptacle for connection

to AC mains power. The power cord, exact type to be supplied in the appropriate Option

Kit, shall be length of 1.8  0.05 meters, and PC99 compliant.

1.5.2 Video Signal Connector

VGA

Signal

1

RED

9

+5V

2

GREEN

10

GND

3

BLUE

11

NC

4

NC

12

SDA

5

GND

13

HSYNC

6

RED_RTN

14

VSYNC

7

GREEN_RTN

15

SCL

8

BLUE_RTN

11

DVI

Signal

1

TMDS Data 2-

13

TMDS 3+

2

TMDS Data 2+

14

+5V DDC Power

3

TMDS Data 2/4 Shield

15

Gnd (+5, Analog V/H Sync)

4

TMDS 4-

16

Hot Plug Detect

5

TMDS 4+

17

TMDS Data 0-

6

DDC Clock

18

TMDS Data 0+

7

DDC Data

19

TMDS Data 0/5 Shield

8

No Connection

20

TMDS Data 5-

9

TMDS Data 1-

21

TMDS Data 5+

10

TMDS Data 1+

22

TMDS Clock Shield

11

TMDS Data 1/3 Shield

23

TMDS Clock+

12

TMDS 3-

24

TMDS Clock-C1

USB 2.0

Signal

1

USB5V

2

D-

3

D+

4

GND

Note

Every on USB2.0 Power current provide 1A(Regular)

12

1.6 Package Overview

LCD Display

USB Cable(A to B)

Power Cord

DC Power Supply

VGA cable

DVI cable

User Manual QR-code

sheet

! Warning!

This product is intended to be supplied by a Listed Power Adapter or DC power

source, rated 12Vdc, 2.5A minimum, Tma = 40 degree C minimum, and the

altitude of operation = 3048m minimum. If it needs further assistance with

purchasing the power source, please contact to MicroTouch for further

information.

! Mise en garde!

Cet appareil est destiné à être alimenté par un adaptateur secteur homologué ou

une source d'alimentation CC, d’une tension nominale de 12Vdc, 2,5A minimum,

Tma = 40 degrés C minimum et l’altitude de l’utilisation = 3048m minimum. Pour

d’autres conseils pour l’installation de la source d’alimentation, communiquer

avec MicroTouch pour de plus amples renseignements.

13

Chapter 2

Product Installation

14

2.1 About VESA Mount

The OF-150P-A1 series conform to the “VESA Flat Display Mounting Interface

Standard” which defines a physical mounting interface for touch monitor, and

corresponding with the standards of touch monitor mounting devices. The VESA mount

is located on the back of this unit.

! Warning!

Please select the MicroTouch original screws!

The distance between the back cover surface and the bottom of the screw hole

is 8 mm and 18 mm. Please use four M4 screws diameter with proper length to

mount your monitor.

Note: The mounting stand must be able to support at least 7.67 lbs (3.48 Kg).

VESA

Mount

15

! Mise en garde!

Sélectionner les vis d’origine de MicroTouch!

La distance entre la surface du couvercle arrière et le bas de l’orifice de la vis est

de 8 mm et 18mm. Utiliser les vis M4 de diamètre pour le montage de votre

moniteur.

Remarque : Le support de montage doit pouvoir supporter un poids d’au moins

7.67 lb (3,48kg).

16

2.2 About Wall Mount

The OF-150P-A1 series support wall mount, and this monitor can be mounted to the

wooden or concrete wall with 8 screws and four brackets on the opposites.

2.2.1 Attaching the side Brackets

Depending on your mounting scheme, alternately, you may use the side brackets to

mount your displays onto your wall or device.

Find a suitable location for attaching side brackets.

A. The left and right sides

B. The Top and bottom sides

17

2.2.2 Customer panel material

A. Wooden wall: Ø4.5mm thru holes for M4 screws w/nuts, or no thru holes,

screws for wood4mm.

B. Sheet metal: concealed head threaded studs M4 w/nuts.

! Warning!

This apparatus is intended to be supported by a Listed Wall Mount Bracket” or

the equivalent.

! Mise en garde!

Cet appareil est conçu pour être supporté par un support de montage mural

homologué ”ou l'équivalent.

18

2.3 On-Screen Display

OSD

Key

Menu off status

Menu on status

Menu appear

Menu disappear/ return to main item

▲

Brightness

Main item select up/ Adjust up

▼

Contrast

Main item select down/ Adjust down



Enter/Select sub-item function

Power On/Off

1. Press the “MENU” button to pop up the “on-screen menu” and press “Up” or

“Down” button to select among the five functions in the main menu.

2. Choose the adjustment items by pressing the “Enter” button.

3. Adjust the value of the adjustment items by pressing the “Up” or “Down” button.

4. With the OSD menu on screen, press “Menu” button to return main menu or exit

OSD.

5. The OSD menu will automatically close, if you have left it idle for a pre-set time.

6. To Lock the OSD / Power menu buttons, please follow the instructions below.

(Please note: the monitor has to be turned ON with a valid signal pre-set)

a. Press “Menu” key, the OSD menu will pops upon display.

b. Press and hold the “Menu” key again with the OSD menu on the screen,

the OSD menu will disappear. Then press the "Power" key 1 time while the

menu key is still being pressed. The “Lock/Unlock” menu will appear for 3

seconds.

c. Use the "Enter" key to select OSD or Power setting then set at “Lock” by

pushing the "UP" or "Down" button.

19

d. When the "UP" or "Down" button is released, the previous setting will be

saved and exit the “Lock/Unlock” menu automatically.

7. To Unlock the OSD / Power menu buttons, please follow the instructions below.

(Please note: the monitor has to be turned ON with a valid signal pre-set)

a. Press and hold the “Menu” key then press the “Power” key simultaneously,

the “Lock/ Unlock” menu will appear for 3 seconds.

b. Use the "Enter" key to select OSD or Power setting then set at “Unlock” by

pushing the "UP" or "Down" button.

c. When the "UP" or "Down" button is released, the previous setting will be

saved and exit the “Lock/Unlock” menu automatically.

Please note:

a. When the OSD Lock function is selected, this indicates that all the buttons

except “power” button are now disabled.

b. When the Power Lock function is selected, this indicates that the power key

is disabled; user can not to turn off the monitor by "Power" key.

La page charge ...

MicroTouch OF-150P-A1 Manuel utilisateur

MicroTouch OF-150P-A1 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents