MicroTouch DS-320P-A1 Manuel utilisateur

DS-320P-A1

Digital Signage Monitor

User Manual

1

About This Document

No part of this publication may be reproduced, transmitted, transcribed, stored in a

retrieval system, or translated into any language or computer language, in any form or

by any means, including, but not limited to, electronic, magnetic, optical, chemical,

manual, or otherwise without prior written permission of MicroTouchTM a TES Company.

The information in this document is subject to change without notice. MicroTouchTM a

TES Company makes no representations or warranties with respect to the contents

herein, and specifically disclaims any implied warranties of merchantability or fitness for

a particular purpose. MicroTouchTM a TES Company reserves the right to revise this

publication and to make changes from time to time in the content hereof without

obligation of MicroTouchTM a TES Company to notify any person of such revisions or

changes. Windows is a registered trademark of Microsoft, Inc. Other brand or product

names are trademarks of their respective holders.

2

Compliance Information

For FCC (USA)

This equipment has been tested and fund to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC Rules. There limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instruction manual,

may cause harmful interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) this device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

For IC (Canada)

CAN ICES-3(A)/NMB-3(A)

For CE (EU)

The device complies with the EMC Directive 2014/30/EU and Low Voltage Directive

2014/35/EU

Warning:

This is a class A product. In a domestic environment this product may cause radio

interference in which case the user may be required to take adequate measures.

3

Renseignements relatifs à la conformité

Pour la FCC (États-Unis).

Ce matériel a fait l’objet d’essais qui ont déterminé qu’il respectait les limites d’un appareil

de classe A selon la partie 15 des règlements de la FCC. Ces limites sont établies pour

assurer une protection raisonnable contre les parasites nuisant à un fonctionnement dans

un environnement commercial. Ce matériel génère, utilise et peut émettre des ondes radio

électriques, et lorsqu’il n’est pas installé et utilisé selon le manuel d’instructions, peut

causer des parasites nuisant aux communications radio. L’utilisation de ce matériel dans

une zone résidentielle est susceptible de causer des parasites auquel cas l’utilisateur est

tenu de corriger le problème des parasites à ses propres frais.

L’appareil respecte la partie 15 des règlements de la FCC. Le fonctionnement doit

respecter les deux conditions suivantes : 1) cet appareil ne doit pas causer de parasites et

(2) cet appareil doit accepter tous les parasites reçus, notamment ceux pouvant causer un

fonctionnement non voulu.

Pour Industrie Canada

Norme canadienne NMB-3(A)

Pour la CE (UE)

L’appareil respecte la directive 2014/30/UE relative à la compatibilité électromagnétique et

la directive 2014/35/EU sur les limites de basse tension

Avertissement :

Ceci est un produit de classe A. Dans un environnement résidentiel ce produit peut causer

des parasites radio auquel cas l’utilisateur peut être tenu de prendre les mesures

nécessaires.

4

Usage Notice

Precautions

Please follow all warnings, precautions and maintenance as recommended in this user’s

manual to maximize the life of your unit.

Do

：

▪ Turn off the product before cleaning.

▪ Use a soft cloth moistened with mild detergent to clean the product housing.

▪ Use only the qualified power adapter that comes with your device.

▪ Disconnect the power plug from AC outlet if the product is not going to be used for an

extended period of time.

Don’t

：

▪ Do not use abrasive cleaners, waxes or solvents for your cleaning.

▪ Do not operate the product under the following conditions:

- Extremely hot, cold or humid environment.

- Areas susceptible to excessive dust and dirt.

- Near any appliance generating a strong magnetic field.

! Warning - To prevent the risk of fire or shock hazards, and do not

expose the product to moisture.

! Warning - Please do not open or disassemble the product as this may

cause electric shock.

! Warning - Power cord shall be connected to a socket-outlet with

earthing connection.

! Warning - The cable cover cannot be removed under normal use

conditions.

! Warning - Stability Hazard. The touch monitor may fall, causing

serious personal injury or death. To prevent injury, this

touch monitor must be securely attached to the wall in

accordance with the installation instructions.

5

Avis d’utilisation

Précautions

Veuillez suivre toutes les mises en garde, précautions et entretiens recommandés dans

ce manuel d’utilisation pour maximiser la durée de vie de votre unité.

À faire :

▪ Éteindre l’appareil avant de le nettoyer.

▪ Utiliser un chiffon humidifié par une solution savonneuse pour nettoyer le boîtier du

produit.

▪ Utiliser uniquement l’adaptateur d’alimentation prescrit pour votre appareil.

▪ Débrancher l’appareil lorsqu’il n’est pas utilisé pendant une période prolongée.

À éviter :

▪ Ne pas utiliser de nettoyants abrasifs, de cires ou de solvants pour le nettoyage

▪ Ne jamais utiliser l’appareil dans les conditions suivantes :

– des conditions environnementales extrêmes (chaud, froid ou humidité)

– des endroits remplis de poussières et de saletés.

– à proximité d’appareils produisant un fort champ magnétique.

! Mise en garde — Pour prévenir les risques d’incendie ou

d’électrocution, ne pas exposer le produit à l’humidité.

! Mise en garde — Prière de ne pas ouvrir ou démonter le produit, car

cela pourrait entraîner l’électrocution.

! Mise en garde – Le cordon d’alimentation doit être branché à une

prise pourvue d’une mise à la terre.

! Mise en garde – La gaine du câble ne doit pas être retirée en

conditions normales d’utilisation.

! Mise en garde — Risque de renversement. Le moniteur tactile peut se

renverser et causer de graves blessures corporelles, voire la mort.

Pour prévenir les blessures, ce moniteur tactile doit être solidement

fixé au mur selon les instructions d’installation.

 
     
 
Table of Contents 
 
Chapter 1 ........................................................................................................................ 7 
1 Overview .................................................................................................................... 8 
2 Feature ...................................................................................................................... 8 
3 Specifications ............................................................................................................. 8 
4 Block Diagram............................................................................................................ 9 
5 Interface Connectors ................................................................................................ 10 
5.1 Power Connector ............................................................................................. 10 
5.2 Video Signal Connector ................................................................................... 10 
6 Package Overview ................................................................................................... 12 
Chapter 2 ...................................................................................................................... 14 
1 About VESA Mount .................................................................................................. 15 
1.1 Install the VESA screw ..................................................................................... 16 
2 About General Mounting Information ....................................................................... 17 
2.1 Landscape ....................................................................................................... 17 
2.2 Portrait ............................................................................................................. 17 
3 On-Screen Display ................................................................................................... 18 
3.1 OSD Function Description ................................................................................ 20 
3.2 Timing Table Chart ........................................................................................... 21 
3.3 EDID Data ........................................................................................................ 21 
4 Dimension ................................................................................................................ 22 
4.1 Front View ........................................................................................................ 22 
4.2 Side View ......................................................................................................... 22 
4.3 Rear View ........................................................................................................ 23 
Appendix ...................................................................................................................... 24 
 
 

7

Chapter 1

Product Introduction

8

1.1 Overview

DS-320P-A1 series supports landscape or portrait and low power consumption at the

maximum consumption of 70W. DS-320P-A1 provides application for Interactive

whiteboard and digital signage.

1.2 Feature

▪ VESA mounting holes for various mounting options.

▪ Multilingual OSD user control

▪ High Resolution FHD (1920 x 1080)

1.3 Specifications

LCD Touch Panel

Size

31.5” TFT LCD

Brightness

400 cd/m2 (Non-touch screen)

360 cd/m2 (P-CAP)

Number of Pixels

1920(H) x 1080(V)

Touch Type

P-CAP/ 10 points

Environment

Power Input

100-240V ~ 1.2A 50/60Hz

Operating Temperature

0C ~ 40C

Storage Temperature

-20C ~ 60C

Operating Humidity

20% ~ 80% RH, non-condensing

Mounting

VESA 400 mm x 200 mm

Dimension (W x H x D)

476.1mm x 66.8mm x 781.5 mm

Net Weight

15.0 kg

Gross Weight

18.0 kg

9

1.4 Block Diagram

This section describes the electrical requirements of the monitor. The block

diagram in figure 1 illustrates the various electrical sub-systems.

10

1.5 Interface Connectors

1.5.1 Power Connector

The monitor shall have a power control switch visible and accessible on the bottom

of the monitor. The power switch shall be marked with icons per IEC 417, #5009.

The operation of the power switch should be programmable thru monitor firmware

control.

1.5.2 Video Signal Connector

The video signal input via D-type 15-pin female connector.

Connector Pin Assignment:

Signal

1

Red video signal input

2

Green video signal input

3

Blue video signal input

4

NC

5

DDC ground for the VESA DDC2B function

6

Analog signal ground for the red video

7

Analog signal ground for the Green video

8

Analog signal ground for the blue video

9

+ 5V: Input from host system for the VESA DDC2B function

10

Signal ground

11

NC

12

SDA signal input for the VESA DDC2B function

13

Horizontal signal input from host system

14

Vertical signal input from host system

15

SCL signal input for the VESA DDC2B function

11

The video signal input via HDMI female connector.

Connector Pin Assignment:

Signal

1

TMDS Data2+

11

TMDS Clock Shield

2

TMDS Data2 Shield

12

TMDS Clock–

3

TMDS Data2–

13

CEC

4

TMDS Data1+

14

Reserved (N.C. on device)

5

TMDS Data1 Shield

15

SCL

6

TMDS Data1–

16

SDA

7

TMDS Data0+

17

DDC/CEC Ground

8

TMDS Data0 Shield

18

+5V Power

9

TMDS Data0–

19

Hot Plug Detect

10

TMDS Clock+

The video signal input via DVI female connector.

Connector Pin Assignment:

Signal

1

TMDS Data 2-

13

TMDS 3+

2

TMDS Data 2+

14

+5V DDC Power

3

TMDS Data 2/4 Shield

15

Gnd (+5, Analog V/H Sync)

4

TMDS 4

16

Hot Plug Detect

5

TMDS 4

17

TMDS Data 0-

6

DDC Clock

18

TMDS Data 0+

7

DDC Data

19

TMDS Data 0/5 Shield

8

No Connection

20

TMDS Data 5-

9

TMDS Data 1-

21

TMDS Data 5+

10

TMDS Data 1+

22

TMDS Clock Shield

11

TMDS Data 1/3 Shield

23

TMDS Clock+

12

TMDS 3-

24

TMDS Clock-C1

12

1.6 Package Overview

LCD Display

Power Cord

DVI Cable

USB Cable (A to B)

HDMI Cable

VGA cable

Nut x 2

Screw (M5 x 8mm)

x 4 pcs

Washer x 2

13

! Warming!

This product is intended to be supplied by a AC-in Power source, rated

100V~240V, 1.2A 50/60Hz minimum, Tma = 40 degree C minimum, and the

altitude of operation = 3048m minimum. If it needs further assistance with

purchasing the power source, please contact to MicroTouch for further

information.

! Mise en garde!

Cet appareil est conçu avec une alimentation de courant CA, d’une tension

nominale de 100 V~240 V, 1,2A 50/60 Hz minimum, Tma = 40 degrés C minimum

et l’altitude de l’utilisation = 3048 m minimum. Pour d’autres conseils pour

l’installation de la source d’alimentation, communiquer avec MicroTouch pour

de plus amples renseignements.

14

Chapter 2

Product Installation

15

2.1 About VESA Mount

The DS-320P-A1 series conform to the “VESA Flat Display Mounting Interface

Standard” which defines a physical mounting interface for touch monitor and

corresponding with the standards of touch monitor mounting devices. The VESA

mount is located on the back of this unit.

! Warming!

Please select the MicroTouch original screws!

The distance between the back cover surface and the bottom of the screw hole

is 6~7 mm. Please use M5 screws diameter with proper length to mount your

monitor.

Note: The mounting stand must be able to support at least 33 lbs (15.0 Kg).

! Mise en garde!

Sélectionner les vis d’origine de MicroTouch!

La distance entre la surface du couvercle arrière et le bas de l’orifice de la vis est

de 6 ~7mm. Utiliser les vis M5 de diamètre pour le montage de votre moniteur.

Remarque : Le support de montage doit pouvoir supporter un poids d’au moins 33

lb (15,0kg).

16

2.1.1 Install the VESA screw

Note: Please install/ dismantle the product when the device is in the shutdown state.

Step 1: Fasten two M5 screws nut into the VESA hole

The length of screw nut is 30mm

Step 2: Fasten four M5 screws into the VESA hole

The specification of screw is M5 x 8mm

17

2.2 About General Mounting Information

The following two mounting orientations are supported: Landscape and portrait

mode. For optimal touch performance, ensure that the monitor is supported fully and

is as flat as possible.

2.2.1 Landscape

2.2.2 Portrait

18

2.3 On-Screen Display

The OF-320P-A1 provide side panel controls. And the following is OSD function

table:

OSD

Key

Menu off status

Menu on status

MENU

Menu appear

Menu disappear/ return to main item

▲

Brightness

Main item select up/ Adjust up

▼

Contrast

Main item select down/ Adjust down

SELECT

Auto Adjusting

Enter/Select sub-item function

Power On/Off

1. Press the “MENU” button to pop up the “on-screen menu” and press “Up” or

“Down” button to select among the five functions in the main menu.

2. Press “SELECT” to enter the sub menu , and then use “Up” or “Down” button to

select the adjustable functions.

3. Choose the adjustment items in the sub menu by pressing the “SELECT ”

button.

4. Adjust the value of the adjustment items by pressing the “Up” or “Down” button.

5. With the OSD menu on screen, press “Menu” button to return main menu or exit

OSD.

6. The OSD menu will automatically close, if you have left it idle for a pre-set time.

7. To Lock the OSD / Power menu buttons, please follow the instructions below.

(Please note: the monitor has to be turned ON with a valid signal pre-set)

a. Without the OSD menu on screen, press and hold “Menu” key ,and press

“POWER” once then release “MENU” key. The “Lock/Unlock” menu will

appear for 5 seconds.

b. Use the "UP” and “DOWN key to select OSD or Power setting then set at

“Lock” (or “Unlock” ) by pushing the "ENTER" button.

c. When pressing “MENU” button , the previous setting will be saved and

exit the “Lock/Unlock” menu automatically.

Please note:

19

1. When the OSD Lock function is selected, this indicates that all the buttons

except “power” button are now disabled.

2. When the Power Lock function is selected, this indicates that the power key is

disabled; user can not to turn off the monitor by "Power" key.

3. How to enter factory OSD menu, please follow the instructions below.

a. Without the OSD menu on screen, press and hold “Menu” key ,and press

“UP” once then release “MENU” key. The factory menu will appear on the

screen.

d. Use the "UP” and “DOWN key to select main functions, then press

“SELECT” to enter sub menu for adjusting (or setting) those values.

c. Select “GoTo Main” and press “SELECT” to exit factory OSD menu, it will

automatically switch to user menu for normal OSD operation.

4. In power saving status, to press “Menu” button can wake up OSD for selecting

video port.

La page charge ...

MicroTouch DS-320P-A1 Manuel utilisateur

MicroTouch DS-320P-A1 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents