MicroTouch SK-150P-A1 Slimline Kiosk Touch Monitor Manuel utilisateur

SK-170P-A1

Slimline Kiosk Touch Monitor

User Manual

1

About This Document

No part of this publication may be reproduced, transmitted, transcribed, stored in a

retrieval system, or translated into any language or computer language, in any form or

by any means, including, but not limited to, electronic, magnetic, optical, chemical,

manual, or otherwise without prior written permission of MicroTouchTM a TES Company.

The information in this document is subject to change without notice. MicroTouchTM a

TES Company makes no representations or warranties with respect to the contents

herein, and specifically disclaims any implied warranties of merchantability or fitness for

a particular purpose. MicroTouchTM a TES Company reserves the right to revise this

publication and to make changes from time to time in the content hereof without

obligation of MicroTouchTM a TES Company to notify any person of such revisions or

changes. Windows is a registered trademark of Microsoft, Inc. Other brand or product

names are trademarks of their respective holders.

2

Compliance Information

For FCC (USA)

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy, and if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) this device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

For IC (Canada)

CAN ICES-3(B)/NMB-3(B)

For CE (EU)

The device complies with the EMC Directive 2014/30/EU and Low Voltage Directive

2014/35/EU

3

Renseignements relatifs à la conformité

Pour la FCC (États-Unis).

Ce matériel a fait l’objet d’essais qui ont déterminé qu’il respectait les limites d’un appareil

de classe B selon la partie 15 des règlements de la FCC. Ces limites sont établies pour

assurer une protection raisonnable contre les parasites nuisant à une installation

résidentielle. Ce matériel génère, utilise et peut émettre des ondes radio électriques, et

lorsqu’il n’est pas installé et utilisé selon les instructions, peut causer des parasites

nuisant aux communications radio. Il n’y a toutefois aucune garantie qu’il n’y aura pas de

parasites dans une installation en particulier. Si ce matériel cause des parasites à la

réception d’ondes radio ou de télévision, ce qui peut être déterminé en l’éteignant et en

l’allumant, l’utilisateur est invité à essayer de corriger le problème des parasites par l’une

ou l’autre des mesures suivantes :

• Réorienter ou déplacer l’antenne de réception.

• Augmenter la distance entre le matériel et la réception.

• Brancher le matériel dans une prise sur un autre circuit que celui où le récepteur est

branché.

• Consulter le distributeur ou un technicien radio ou TV expérimenté pour des conseils.

L’appareil respecte la partie 15 des règlements de la FCC. Le fonctionnement doit

respecter les deux conditions suivantes : 1) cet appareil ne doit pas causer de parasites et

(2) cet appareil doit accepter tous les parasites reçus, notamment ceux pouvant causer un

fonctionnement non voulu.

Pour Industrie Canada

Norme canadienne NMB-3(B)

Pour la CE (UE)

L’appareil respecte la directive 2014/30/UE relative à la compatibilité électromagnétique et

la directive 2014/35/EU sur les limites de basse tension

4

Usage Notice

Precautions

Please follow all warnings, precautions and maintenance as recommended in this user’s

manual to maximize the life of your unit.

Do

：

▪ Turn off the product before cleaning.

▪ Use a soft cloth moistened with mild detergent to clean the product housing.

▪ Use only the qualified power adapter that comes with your device.

▪ Disconnect the power plug from AC outlet if the product is not going to be used for an

extended period of time.

Don’t

：

▪ Do not use abrasive cleaners, waxes or solvents for your cleaning.

▪ Do not operate the product under the following conditions:

- Extremely hot, cold or humid environment.

- Areas susceptible to excessive dust and dirt.

- Near any appliance generating a strong magnetic field.

! Warning - To prevent the risk of fire or shock hazards, and do not

expose the product to moisture.

! Warning - Please do not open or disassemble the product as this may

cause electric shock.

! Warning - Power cord shall be connected to a socket-outlet with

earthing connection.

! Warning - The cable cover cannot be removed under normal use

conditions.

! Warning - Stability Hazard. The touch monitor may fall, causing

serious personal injury or death. To prevent injury, this

touch monitor must be securely attached to the wall in

accordance with the installation instructions.

5

Avis d’utilisation

Précautions

Veuillez suivre toutes les mises en garde, précautions et entretiens recommandés dans

ce manuel d’utilisation pour maximiser la durée de vie de votre unité.

À faire :

▪ Éteindre l’appareil avant de le nettoyer.

▪ Utiliser un chiffon humidifié par une solution savonneuse pour nettoyer le boîtier du

produit.

▪ Utiliser uniquement l’adaptateur d’alimentation prescrit pour votre appareil.

▪ Débrancher l’appareil lorsqu’il n’est pas utilisé pendant une période prolongée.

À éviter :

▪ Ne pas utiliser de nettoyants abrasifs, de cires ou de solvants pour le nettoyage

▪ Ne jamais utiliser l’appareil dans les conditions suivantes :

– des conditions environnementales extrêmes (chaud, froid ou humidité)

– des endroits remplis de poussières et de saletés.

– à proximité d’appareils produisant un fort champ magnétique.

! Mise en garde — Pour prévenir les risques d’incendie ou

d’électrocution, ne pas exposer le produit à l’humidité.

! Mise en garde — Prière de ne pas ouvrir ou démonter le produit, car

cela pourrait entraîner l’électrocution.

! Mise en garde – Le cordon d’alimentation doit être branché à une

prise pourvue d’une mise à la terre.

! Mise en garde – La gaine du câble ne doit pas être retirée en

conditions normales d’utilisation.

! Mise en garde — Risque de renversement. Le moniteur tactile peut se

renverser et causer de graves blessures corporelles, voire la mort.

Pour prévenir les blessures, ce moniteur tactile doit être solidement

fixé au mur selon les instructions d’installation.

 
   
 Table of Contents 
 
Chapter 1 ........................................................................................................................ 7 
1 Overview .................................................................................................................... 8 
2 Feature ...................................................................................................................... 8 
3 Specifications ............................................................................................................. 8 
4 Block Diagram............................................................................................................ 9 
5 Interface Connectors ................................................................................................ 10 
5.1 Power Connector ............................................................................................. 10 
5.2 Video Signal Connector ................................................................................... 10 
5.3 Signal Connector .............................................................................................. 12 
6 Package Overview ................................................................................................... 13 
Chapter 2 ...................................................................................................................... 14 
1 About VESA Mount .................................................................................................. 15 
2 On-Screen Display ................................................................................................... 16 
2.1 OSD Function Description ................................................................................ 18 
2.2 Timing Table Chart ........................................................................................... 19 
2.3 EDID Data ........................................................................................................ 19 
3 Dimension ................................................................................................................ 20 
3.1 Front View ........................................................................................................ 20 
3.2 Side View ......................................................................................................... 20 
3.3 Rear View ........................................................................................................ 21 
Appendix ...................................................................................................................... 22 
 
 

7

Chapter 1

Product Introduction

8

1.1 Overview

The SK-170P-A1 series is a 17” touchscreen monitor that builds to withstand commercial

grade open frame monitor, with stylish thin cable management bracket and versatile

design SK-170P-A1 is an exceptional choice for applications for all business sectors and

well suited for point-of-sales, point-of-information, point-of-service and interactive signage.

1.2 Feature

▪ Cable management bracket design for easy organize cable.

1.3 Specifications

LCD Touch Panel

Size

17” TFT LCD

Brightness

250 cd/m2 (Non-touch screen)

225 cd/m2 (P-cap touch)

Number of Pixels

1280(H) ×1024 (V)

Touch Type

P-CAP/ 10 points

Environment

Certificate

CE、FCC、UL/cUL

Compliance

Front Panel IP65 Compliant, Rear IPX1

Operating Temperature

0C ~ 40C

Storage Temperature

-20C ~ 60C

Operating Humidity

20% ~ 80% RH, non-condensing

Mounting

VESA 100 mm x 100 mm

Dimension (W x H x D)

369 x 307 x 47.3 mm

Net Weight

3.6 kg

Gross Weight

5.2 kg

9

1.4 Block Diagram

10

1.5 Interface Connectors

1.5.1 Power Connector

The DC power via external 12V Adapter provide it

1.5.2 Video Signal Connector

VGA

The video signal input via D-type 15-pin female connector.

Connector Pin Assignment:

Signal

1

RED

2

GREEN

3

BLUE

4

NC

5

GND

6

RED_RTN

7

GREEN_RTN

8

BLUE_RTN

9

+5V

10

GND

11

NC

12

SDA

13

HSYNC

14

VSYNC

15

SCL

11

Display Port(1.2a)

Signal

1

ML_Lane 0(p) Data0 +

11

Signal ground

2

Signal ground

12

ML_Lane 3(n) Data3 -

3

ML_Lane 0(n) Data0 -

13

Signal ground

4

ML_Lane 1(p) Data1 +

14

Signal ground

5

Signal ground

15

AUX_CH(p) AUX + Signal for

Auxiliary Channel

6

ML_Lane 1(n) Data1 -

16

Signal ground

7

ML_Lane 2(p) Data2 +

17

AUX_CH(n) AUX - Signal for

Auxiliary Channel

8

Signal ground

18

Hot Plug

9

ML_Lane 2(n) Data 2 -

19

DP_PWR Return

10

ML_Lane 3(p) Data3 +

20

DP_PWR

HDMI(1.3) (compatible with HDMI1.4)

Signal

1

TMDS Data2+

11

TMDS Clock Shield

2

TMDS Data2 Shield

12

TMDS Clock–

3

TMDS Data2–

13

CEC

4

TMDS Data1+

14

Reserved (N.C. on device)

5

TMDS Data1 Shield

15

SCL

6

TMDS Data1–

16

SDA

7

TMDS Data0+

17

DDC/CEC Ground

8

TMDS Data0 Shield

18

+5V Power

9

TMDS Data0–

19

Hot Plug Detect

10

TMDS Clock+

12

1.5.3 Signal Connector

USB Connector

Signal

1

VCC

3

D+

2

D-

4

GND

RJ11 Connector (for Remote Key) (option)

Signal

1

MENU

4

SELECT

2

UP

5

POWER

3

DOWN

6

GND

13

1.6 Package Overview

LCD Display

Power Cord

DC Power Supply

HDMI Cable

VGA cable

USB cable (A to B)

M3 screw

! Warming!

This product is intended to be supplied by a Listed Power Adapter or DC power

source, rated 12Vdc, 2.5A minimum, Tma = 40 degree C minimum, and the

altitude of operation = 3048m minimum. If it needs further assistance with

purchasing the power source, please contact to MicroTouch for further

information.

! Mise en garde!

Cet appareil est conçu avec une alimentation de courant CA, d’une tension

nominale de 12Vdc, 2.5A minimum, Tma = 40 degrés C minimum et l’altitude de

l’utilisation = 3048 m minimum. Pour d’autres conseils pour l’installation de la

source d’alimentation, communiquer avec MicroTouch pour de plus amples

renseignements.

14

Chapter 2

Product Installation

15

2.1 About VESA Mount

The SK-170P-A1 series conform to the “VESA Flat Display Mounting Interface

Standard” which defines a physical mounting interface for touch monitor, and

corresponding with the standards of touch monitor mounting devices. The VESA

mount is located on the back of this unit.

VESA Mount

! Warming!

Please select the MicroTouch original screws!

The distance between the back cover surface and the bottom of the screw hole

is 8 mm. Please use four M4 screws diameter with 8-10mm proper length to

mount your monitor.

Note: The mounting stand must be able to support at least 7.67 lbs (3.48 Kg).

! Mise en garde!

Sélectionner les vis d’origine de MicroTouch!

La distance entre la surface du couvercle arrière et le bas de l’orifice de la vis

est de 8 mm et 18mm. Utiliser les vis M4 de diamètre pour le montage de

votre moniteur.

Remarque : Le support de montage doit pouvoir supporter un poids d’au moins

7.67 lb (3,48kg).

16

2.2 On-Screen Display

OSD

Key

Menu off status

Menu on status

MENU

Menu appear

Menu disappear/ return to main item

▲

Brightness

Main item select up/ Adjust up

▼

Contrast

Main item select down/ Adjust down

SELECT

Enter/Select sub-item function

Power On/Off

1. Press the “MENU” button to pop up the “on-screen menu” and press “Up” or

“Down” button to select among the four functions in the main menu.

2. Choose the adjustment items by pressing the “SELECT ” button.

3. Adjust the value of the adjustment items by pressing the “Up” or “Down” button.

4. With the OSD menu on screen, press “ Menu” button to return main menu or exit

OSD.

5. The OSD menu will automatically close, if you have left it idle for a pre-set time.

6. To Lock / Unlock the OSD / Power menu buttons, press “Menu” and “Minus” at

the same time to select.

OSD / Power the Lock / Unlock function.

17

Please note:

a. When the OSD Lock function is selected, this indicates that all the buttons

except “power” button are now disabled.

b. When the Power Lock function is selected, this indicates that the power key

is disabled; user can not to turn off the monitor by "Power" key.

7. To disable the touch function, press “Menu” and “Enter” Key, at the same time.

8. To enable the touch function, press “Menu” and “Enter” Key, at the same time

for five seconds.

9. Press the power key button, there will be an OSD window pop up to ask if it

should be going off.

If press the power key in five seconds, the monitor power will be off. If don’t

press the power key in five seconds, the OSD window will be gone and return to

the normal status instead.

10. Direct input select function.

a. Normal:Press and keep pressing “Select” key for 3 seconds, will change to

pop up “source select” OSD.

b. Sleep status:Press and keep pressing “Select” key for 1 seconds, will

change to pop up “source select” OSD.

11. Factory mode: Press the “MENU” button to pop up the “on-screen menu” and

select "Option" icon in "Factory" item, key in password "3","3","3","3" into factory

mode.

12. Burn-in mode: In Factory mode to select “Burn In” item into Burin-in mode

(unplug signal cable or do not enter the signal source).

13. Work time: In factory mode, displays monitor the work time counting in hours.

18

2.2.1 OSD Function Description

Item

Content

Default

Contrast

The monitor luminance level control.

50

Brightness

The monitor backlight level control.

100

H-Positon

Moving screen image horizontal position to left or right.

NA

V-Positon

Moving screen image vertical position to up or down.

NA

Phase

The screen image horizontal dot clock adjustment.

NA

Clock

The screen image pixel phase adjustment.

NA

Auto Adjust

Fine-tune the image to full screen automatically.

NA

OSD Timeout

OSD auto-disappear time selection.

15

Reset

Factory default value restored.

NA

OSD Language

OSD menu language selection.

( English, French, Deutsch, Italian,Spanish, Japanese,

Traditional Chinese and Simplified Chinese)

English

Source Select

Select Input function.(Auto, VGA,HDMI,DP)

Auto

Factory

Factory mode related adjustment items.

NA

19

2.2.2 Timing Table Chart

Mode

Resolution

H-Freq.

(KHz)

Band Width

(MHz)

Polarity

H

V

1

VGA 720x400 70Hz

31.47

28.322

-

+

2

VGA 640x480 60Hz

31.47

25.175

-

3

MAC 640x480 66Hz

35

32.24

-

4

VESA 640x480 72Hz

37.86

31.5

-

5

VESA 640X480 75Hz

37.5

31.5

-

6

VESA 800x600 56Hz

35.16

36

+

7

VESA 800x600 60Hz

37.88

40

+

8

VESA 800x600 75Hz

46.88

49.5

+

9

VESA 800x600 72Hz

48.08

50

+

10

MAC 832x624 75Hz

49.72

57.283

-

11

VESA 1024x768 60Hz

48.36

65

-

12

VESA 1024x768 70Hz

56.48

75

-

13

VESA 1024x768 75Hz

60.02

78.75

+

14

SXGA 1280x1024 60Hz

64

108

+

15

SXGA 1280x1024 75Hz

80

135

+

16

SXGA 1152x864 75Hz

67.5

108

+

17

SXGA 1280x960 60Hz

60

108

+

2.2.3 EDID Data

DP/HDMI

The monitor assembly shall provide a display communications channel that

conforms to VESA DDC2B hardware requirements. This configuration shall contain

the 256-byte EDID file as specified by VESA EDID Standard

VGA

The monitor assembly shall provide a display communications channel that

conforms to VESA DDC2B hardware requirements. This configuration shall contain

the 128-byte EDID file as specified by VESA EDID Standard

La page charge ...

MicroTouch SK-150P-A1 Slimline Kiosk Touch Monitor Manuel utilisateur

MicroTouch SK-150P-A1 Slimline Kiosk Touch Monitor Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents