Swing-N-Slide Playsets 4429 Mode d'emploi

2999-18

Call Us First!

DO NOT RETURN TO STORE.

For immediate help with assembly or product information

Call our toll-free number:

1-866-890-2211

April through October M - F 8:00 AM to 6:00 PM EST

Saturday 8:30 AM to 4:30 PM EST

November through March M - F 8:00 AM to 5:00 PM EST

or email:

customerservice@backyard-play.com

Our staff is ready to provide assistance.

- NOTICE -

This playset product is not intended for public use. It is intended for

residential application and is not warranted for public or commercial use.

STOP!

(This page intentionally left blank.)

02/18/2018

- BEFORE YOU BEGIN -

Your premium playset is manufactured from wood which has many natural characteristics and blemishes that may be present in some of the pieces in your playset. These natural characteristics may include knots or mi-

nor cracks/splits. All individual parts have been cut to provide a smooth and safe surface. All parts have been inspected to assure we pack only the safest, most durable wood product. Any minor blemishes in your playset

will not affect the strength, durability, or structural integrity of the nished product. Our limited warranty does not cover the imperfections not resulting in structural failure.

2999-18

Playset

First...



Check with your homeowner’s association before

assembling.



Read instructions thoroughly before you begin. If you

have purchased accessories to accompany this play

set, please read all installation instructions before

beginning assembly of this structure.

Check All Parts



If a part is missing, circle the part in question and call.

Important



In a drawing, a dotted line represents a part hidden

from view (like a part under a panel).

Adult Assistance required



Assistance is necessary to handle, t

and secure some components.

Squareness is very Important!

Start with a level surface and keep 90° corners and 90°

perpendiculars throughout the assembly to ensure all

components t together.

Safety!



Check for protruding screws and bolts, verify all screw

and bolt lengths during assembly.

Always wear OSHA-APPROVED safety

glasses throughout assembly process.

Tools Required

Socket Set

Hammer

9/16" Combination

Wrench

3/16" Allen Wrench

#2 Square Drive

Bit

T-20 Torque Drive

Bit

#3 Phillips Bit

Cordless Drill

w/Charger

1/8" Drill Bit

7/16" Drill Bit

1/4" Drill Bit

3/8" Drill Bit

Tape Measure

Level

C - Clamps

8' Step Ladder

Framing/Speed

Square

- BEFORE YOU BEGIN -

Recommended for Ages 3 to 11

Backyard Play Systems

Customer Service

1-866-890-2211

1000 Ternes Drive

Monroe, MI 48162

- NOTICE -

This playset product is not intended for public use. It is intended for

residential application and is not warranted for public or commercial use.

Model 4429

2



Wear safety glasses during drilling, assembly of your playset.



Children should not be allowed in the playset assembly and build area.



Note the hole orientation on parts to avoid having to take parts

apart later.



Some steps require the assistance of two people to ensure proper

assembly, safety during assembly, as well as preventing any damage

to the playset.



All hex bolts and lag bolts require a lock washer or lock nut.



To properly install lock nuts, two to three threads must protrude past the

lock nut and be exposed once tightened.



Due to wood characteristics and the manufacturing process hex bolts

may protrude past a surface. If this condition occurs add additional

supplied washers to eliminate bolt protrusion.



To aid in proper assembly pound T-nuts into their respective hole

prior to assembly



Pound in T-nuts while the part is on the ground to ensure proper seating.



Use a soft material under parts when pounding in T-nuts to ensure

no scratching or de-facing of parts.



Make sure all fasteners used are as specied. Using a fastener not

specied in a particular application may result in too much thread

exposure or not enough thread engagement.

ASSEMBLY SAFETY and HELPFUL HINTS

STOP!!! Check all parts and hardware before beginning. If any parts are

missing or damaged please circle and call the phone number listed.

DO NOT CONTACT THE STORE OR RETURN YOUR PLAYSET !

KEEP THIS INSTALLATION MANUAL FOR FUTURE CARE

AND MAINTENANCE REFERENCE.

To aid in making your playset assembly easier,

here is a listing of some helpful hints.

*IMPORTANT HARDWARE INFORMATION*

3

SAFETY WARNINGS



This playset has been designed for use by a maximum of 12 occupants at one time having a

combined weight of 1,260 pounds. (This weight does not include occupants in the sandbox area.)





This playset is recommended for children (3) through (11) years of age.



On-site adult supervision for children of all ages is recommended.



Instruct children not to walk close to, in front of, behind, or between moving items.



Instruct children not to twist swing chains or ropes or loop them over the top support bar since this may

reduce the strength of the chain or rope.



Instruct children to avoid swinging empty seats.



Teach children to sit in the center of the swings with their full weight on the seats.



Instruct children not to use the equipment in a manner other than intended.



Instruct children not to get off equipment while it is in motion.



Parents should dress children appropriately (examples would include the use of well-tting shoes and

the avoidance of ponchos, scarves, and other loose-tting clothing that is potentially hazardous

while using equipment).



Instruct children not to climb when the equipment is wet. Slippery surfaces may cause a hazard.



Verify that suspended climbing ropes, chain, or cable are secured at both ends.



Verify that suspended climbing ropes, chain, or cable cannot be looped back on itself.



Instruct children not to attach items to the playground equipment that are not specically designed for

use with the equipment, such as, but not limited to, jump ropes, clothesline, pet leashes, cables and

chain as they may cause a strangulation hazard.



Instruct children to remove their bike or other sports helmet before playing on the playground equipment.



Instruct children to not walk or run up slides.



Instruct children to not pick up slides or ramps as this may cause damage or breakage.



Place the equipment on level ground not less than six (6) feet from any obstructions. Be sure to look

overhead for any obstructions above the playset.



Do not use the equipment until fully erected per this playset instruction manual, bolts tightened and

the playset is anchored to the ground.

NOTICE:

This playset product is not intended for public use. It is intended for residential application

and is not warranted for public or commercial use.

Please read carefully. Observing the following statements and warnings

reduces the likelihood of serious or fatal injury.

4

Periodic maintenance is required to ensure safe enjoyment

of your playset and optional accessories.

Observing the following procedures reduces the likelihood of serious or fatal injury.

PLAYSET CHECKLIST

At the beginning of each play season:

Twice a month during play season:

Once a month during play season:

MAINTENANCE



Activity on your playset and optional accessories may loosen fasteners. Check all lock nuts, hex and

lag bolts, quick clips, spring clips, acorn nuts, wood screws, and swing hangers for tightness and

tighten as required. T-nuts should be inspected for full and proper seating into the wood.



Checking, splitting and surface cracking are characteristics of all wooden playsets. This is caused by varying

seasonal temperatures and moisture conditions. To minimize this checking and/or cracking you may coat your

playset with a water repellent.



Tighten all hardware.



Lubricate all metallic moving parts per manufacturer’s instructions.



Check all protective coverings on bolts, pipes, edges, and corners. Replace if they are loose, cracked, or missing.



Check all moving parts including swing seats, ropes, cables, and chains for wear, rust, or other deterioration. Replace as needed.



Check metal parts for rust. If found, sand and repaint using a nonleaded-based paint meeting the requirements of 16 CFR 1303.



Check all wood members for deterioration and splinters. Sand down splinters and replace deteriorating wood members.



Reinstall any plastic parts, such as swing seats or any other items that were removed for the cold season.



Rake and check depth of loose ll protective surfacing materials to prevent compaction and to maintain appropriate depth. Replace as necessary.

Tighten all hardware.

Check all protective coverings on bolts, pipes, edges, and corners. Replace if they are loose, cracked, or missing.

Rake and check depth of loose ll protective surfacing materials to prevent compaction and to maintain appropriate depth. Replace as necessary.

Lubricate all metallic moving parts per manufacturer’s instructions.

Check all moving parts including swing seats, ropes, cables, and chains for wear, rust, or other deterioration. Replace as needed.

At the end of each play season or when the temperature drops below 10°F remove plastic swing seats, tents, sandbox cover, tire swing,

slide and other items as specied by the manufacturer and take indoors or do not use.

Rake and check depth of loose ll protective surfacing materials to prevent compaction and to maintain appropriate depth.Replace as necessary.

When you are ready to dispose of your playset, make sure that all metal, plastic and wood components are disposed of in

accordance with local waste ordinances.

Buyer and/or owner should disassemble and dispose of the playground equipment in such a way that no unreasonable hazards will

exist at the time the swing set is discarded.

5

PLAYGROUND SURFACING MATERIALS

SECTION 4 OF THE CONSUMER PRODUCT SAFETY COMMISSION’S OUTDOOR HOME

PLAYGROUND SAFETY HANDBOOK9

Select Protective Surfacing

One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing protective surfacing under

and around your play equipment. The protective surfacing should be applied to a depth that is suitable for the equipment height in accordance with

ASTM Specication F 1292. There are different types of surfacing to choose from; whichever product you select, follow these guidelines:

NOTE: Do not install home playground equipment over concrete, asphalt, or any other hard surface. A fall onto a hard surface can result in

serious injury to the equipment user. Grass and dirt are not considered protective surfacing because wear and environmental factors can reduce

their shock absorbing effectiveness. Carpeting and thin mats are generally not adequate protective surfacing. Ground level equipment – such as

a sandbox, activity wall, playhouse or other equipment that has no elevated play surface – does not need any protective surfacing.

Loose-Fill Materials:



Maintain a minimum depth of 9 inches of loose- ll materials such as wood mulch/chips, engineered wood ber (EWF), or shredded/recycled

rubber mulch for equipment up to 8 feet high; and 9 inches of sand or pea gravel for equipment up to 5 feet high. NOTE: An initial ll level of

12 inches will compress to about a 9- inch depth of surfacing over time. The surfacing will also compact, displace, and settle, and should be

periodically relled to maintain at least a 9- inch depth.



Use a minimum of 6 inches of protective surfacing for play equipment less than 4 feet in height. If maintained properly, this should be

adequate. (At depths less than 6 inches, the protective material is too easily displaced or compacted.)



Use containment, such as digging out around the perimeter and/or lining the perimeter with landscape edging. Don’t forget to account for

water drainage. U.S Consumer Product Safety Commission, Washington, D.C., 20207 or call the toll-free hotline :1-800-638-2772



Check and maintain the depth of the loose-ll surfacing material. To maintain the right amount of loose-ll materials, mark the correct level on

play equipment support posts. That way you can easily see when to replenish and/or redistribute the surfacing.



Do not install loose ll surfacing over hard surfaces such as concrete or asphalt.

Poured-In-Place Surfaces or Pre-Manufactured Rubber Tiles:

You may be interested in using surfacing other than loose-ll materials – like rubber tiles or poured-in-place surfaces.



Installations of these surfaces generally require a professional and are not "do-it-yourself" projects.



Review surface specications before purchasing this type of surfacing. Ask the installer/manufacturer for a report showing that the product

has been tested to the following safety standard: ASTM F 1292 Standard Specication for Impact Attenuation of Surfacing Materials within the

Use Zone of Playground Equipment. This report should show the specic height for which the surface is intended to protect against serious head

injury. This height should be equal to or greater than the fall height – vertical distance between a designated play surface (elevated surface for

standing, sitting, or climbing) and the protective surfacing below – of your play equipment.

 Check the protective surfacing frequently for wear.

Placement

Proper placement and maintenance of protective surfacing is essential. Be sure to



Extend surfacing at least 6 feet from the equipment in all directions.



For to-fro swings, extend protective surfacing in front of and behind the swing to a distance equal to twice the height of the top bar from which

the swing is suspended.



For tire swings, extend surfacing in a circle whose radius is equal to the height of the suspending chain or rope, plus 6 feet in all directions.

2H 2H

H

L

6 ft.

6 ft. 6 ft.

L+6 ft.

6 ft.

Use Zone for Single-Axis Swings Use Zone for Multi-Axis Swings

Denotes Use Zone with Protective Surfacing

9 This information has been extracted from the CPSC publications "Playground Surfacing—Technical Information Guide" and "Handbook for Public

Playground Safety." Copies of these reports can be obtained by sending a postcard to the: Ofce of Public Affairs, U.S. Consumer Product Safety

Commission, Washington, D.C., 20207 or call the toll-free hotline: 1-800-638-2772

6

ORIENTATION

*Hint*

Throughout this manual references made to the Left Side,

the Right Side, the Front Side and the Back Side of the playset serve

as a consistent reminder to help with assembly.

PLAYSET

LEFT SIDE

FRONT SIDE

BACK SIDE

RIGHT SIDE

7

IMPORTANT!

A

B

Use these Assembly Procedure Hints throughout the installation process.

1. All Lag Bolts must have pre-drilled holes. Use a 1/4” drill bit for all 3/8” Lag Bolts.

Use a 3/16” drill bit for all 5/16” Lag Bolts. Pre-drilling pilot holes will help prevent Screws

and Lag Bolts from breaking and wood from splitting during assembly.

2. In areas where drilling a larger 1/2” hole is neccessary, such as when installing T- Nuts,

(Fig. 1) the recommended procedure is to first drill-through a 1/4” pilot hole from the

Hex Bolt side and then drill the larger 1/2” hole from the opposite T-Nut side. This will

help avoid splintering the wood. The “Drill Both Sides ICON” (Fig. 1) will remind you to

drill according to this procedure. Be sure to clean through-holes of debris before

inserting Hex Bolts.

3. When assembling parts that are difficult to hold in position while pre-drilling pilot holes

or assembling, use a clamp to keep parts aligned or in position. The “Clamp ICON”

(Fig. 2) will advise you to use this procedure.

Fig. 1 (example)

Fig. 2

Drill Both Sides

ICON

Clamp ICON

1/4” pilot hole

1/2” drill through

DO NOT OVER-TIGHTEN LAG BOLTS

8

WOOD PARTS LIST

x1

WOOD PARTS

x2

x6

x1

x4

x1

x2

x16

x1

3/4 x 5-3/8 x 23-3/4"

x2

x1

3/4 x 3 x 38-7/8"

1 x 3-3/8 x 45-1/8"

1-3/8 x 3-3/8 x 51"

1-3/8 x 3-3/8 x 47-3/4"

2899-CC

2502-CC

2521-CC

2522-CC

2966-CC

x4

x1 x1

1 x 3-1/2 x 15-3/8"

1-1/2 x 2-1/2 x 24" 1-3/8 x 3-3/8 x 17-1/4"

2524-CC

2490-CC PF 6295

2974-CC

2976-CC

2955-CC

2953-CC

x2

x1

2962-CC

1816-CC

2505-CC

2969-CC

2971-CC

2972-CC

2523-CC

2977-CC

3/4 x 3-3/8 x 27"

x1

2967-CC

x2

2954-CC

2525-CC

3/4 x 3-3/8 x 28-5/8"

1-3/8 x 3-3/8 x 51"

3 x 3 x 45-1/8"1 x 5-1/2 x 45-1/8"

3/4 x 3-3/8 x 47"

1 x 3-3/8 x 47-1/8"

3/4 x 3-3/8 x 47-1/8"

5/8 x 3-1/4 x 29-3/4"

x1

3/4 x 3-3/8 x 17"

2965-CC

x2

3/4 x 5-3/8 x 23-3/4"

2960-CC

3/4 x 2-1/2 x 45"

x1

2516-CC

x7

2961-CC

3/4 x 5-1/2 x 44-7/8"

x1

2978-CC

1-3/8 x 3-3/8 x 18"

x4

2970-CC

1-3/8 x 3-3/8 x 51"

3 x 3 x 95"

3/4 x 3-3/8 x 53-7/8"

1 x 3-3/8 x 68-1/2"

3-3/8 x 5-3/8 x 95"

3 x 3 x 95"

3/4 x 3-3/8 x 45-1/8"

x1

2968-CC

x2

3/4 x 3-3/8 x 12"

2975-CC

x2x6

x5

x2

1 x 3-3/8 x 40-1/2"3/4 x 5-3/8 x 23-3/4"

3/4 x 3-3/8 x 45-1/8"

1 x 3-3/8 x 37-1/8"

2963-CC2950-CC

2973-CC

2964-CC

9

ACCESSORIES

HARDWARE

Safety Handle

IN BAG

x2

x3

x6

x1

Rope Plaque

Trapeze

Swing

Climbing Rocks

x1

x4

Telescope Steering Wheel

x1

WS 4885 WS 4545

SA 4220 WS 4410

WS 4610 WS 4412

x6

Swing Hanger

2631-B

x1

WS 1501

x1

x4

x1

x2

x1

90

o

Angle Bracket Plate

L-Bracket

Swing Beam Flat Plate

Swing Beam Angled Plate Left Swing Beam Angled Plate RightSwing Beam 90

o

Plate

2411

2448

WS 4521

2447

2485

2412 2449

Anchor Stake

x1

SA 3097

x4

Safety Warning Plate

x1

SA 4294

10

PLAYSET FASTENERS

1"

3/8" T - NUT

5/16" T - NUT

3/8" FLAT WASHER

3/16" x 1" FENDER WASHER

3/8" LOCK WASHER

5/16" FLAT WASHER

5/16" LOCK

WASHER

1/4" LOCK

WASHER

TRUSS HEAD

SCREW

3/4"

3/8" LOCK NUT

2-1/2"

PAN HEAD

SCREW

2-1/2"

1-3/4"

PAN HEAD

SCREW

1-3/4"

3/8"

5/16"

1/4"

1/4" ROCK WALL HARDWARE

T - Nut

Lock

Washer

Hex Bolt

Flat

Washer

1-1/2"

x19

x4

x20

x48

x28

x4

x10

x4

x8

x12

x4

11

PLAYSET FASTENERS

3/8"

LAG BOLT

WOOD SCREWS

4"

2-1/2"

3"

30 mm

2"

3/8"

5"

3/8"

2"

3/8"

3/8” HEX HEAD BOLTS

3-3/4"

1-1/4"

3/8"

1"

3/8"

LAG BOLT

3"

x4

x8

x2 x1

x12

x195

x95

x12

x1

x2

12

3/8" TORQUE

WASHER

3/8"

3"

3-3/4"

4-1/2" 6-1/2"6" 8-1/2"

x5

x2 x6 x2 x2 x2 x1

1-1/2”

3/8”

BUTTON HD.

SCREW

1-1/2”

3/8”

BUTTON HD.

SCREW

1-1/2”

3/8”

BUTTON HD.

SCREW

1-1/2”

3/8”

BUTTON HD.

SCREW

x2

3/8”

LAG BOLT

WOODSCREWS

4”

2-1/2”

3”

1-1/4”

1-5/8”

2”

3/8”

2-1/2”

3/8”

2-1/4”

3/8”

2”

3/8”

3/8” HEX HEAD BOLTS

3-3/4”

1-1/2”

3/8”

1-1/4

”

3/8”

1-3/4”

3/8”

6”

3/8”

LAG BOLT

2-1/2”

3/8”

LAG BOLT

3”

5/16" 5/16"

13

CLUBHOUSE PARTS

CLUBHOUSE PARTS LIST

L-Bracket

x2

2412

3/4 x 3-3/8 x 19-1/4"

5/8 x 3-1/4 x 5"

5/16 x 2-15/16 x 16-13/16"

3/4 x 3 x 6-15/16"

3/4 x 3 x 10-5/16"

x4

x2

x1

1806-CC

x1

1807-CC

1814-CC

1811-CC

2864-CC2852-CC

x2

2853-CC

x5

2855-CC

x8

1813-CC

x9

1808-CC

x2

1810-CC

x2

1809-CC

x2

PF-2990

x5

1826-CC

x1

5/8 x 1-7/8 x 12-7/16"

5/8 x 3/1/4 x 12-7/16"

5/8 x 3-1/4 x 14-3/4"

5/8 x 3-1/4 x 17"

5/8 x 3-1/4 x 9-1/2"

5/8 x 4-7/8 x 29-3/4"

3/4 x 3-3/8 x 45-1/8"

1 x 5-3/8 x 45-1/2"

1-3/8 x 3-3/8 x 51"

1812-CC

x2

Window

14

CLUBHOUSE FASTENERS

WOOD SCREWS

2-1/2"

2"

3/4"

1-3/16"

30 mm

1-1/2”

3/8”

BUTTON HD.

SCREW

1-1/2”

3/8”

BUTTON HD.

SCREW

1-1/2”

3/8”

BUTTON HD.

SCREW

1-1/2”

3/8”

BUTTON HD.

SCREW

x2

3/8”

LAG BOLT

WOODSCREWS

4”

2-1/2”

3”

1-1/4”

1-5/8”

2”

3/8”

1-1/2”

3/8”

1-1/4

”

3/8”

6”

3/8”

LAG BOLT

2-1/2”

3/8”

LAG BOLT

3”

5/16" 5/16"

5/16" T - NUT

5/16" FLAT WASHER

5/16" LOCK

WASHER

5/16"

CLUBHOUSE HARDWARE

x4

x54

x100

x16 x20

15

PLAYSET SET-UP SAFETY AREA

29'- 4"

28'- 6"

6' SAFETY AREA

16'- 6"

10'- 8"

HEIGHT

13'- 4"

FRONT SIDE

BACK SIDE

LEFT SIDE

RIGHT SIDE

SWINGS

SLIDE

TERRACE

LADDER

ROCK

WALL

MONKEY BARS

(This space intentionally left blank.)

16

FORT BOTTOM FRAME BRACE

FLIP ASSEMBLY OVER TO INSTALL BOTTOM BRACE.

Flush

2-1/2"

Wood Screws

x6

x1

2969-CC

90°

FORT

CORNER POSTS

2-1/2" Wood Screw

Align braces with pre-drilled holes.

Ensure all bracing is square before

installing wood screws.

Hole for

Climbing Rope

BOTTOM

T-Nut

x1

2954-CC

2953-CC

3 x 3 x 95"

x1

1 x 3-3/8 x 45-1/8"

x1

3/4 x 3-3/8 x 45-1/8"

2968-CC

2899-CC

x2

3" Lag Bolt

Lock Washer

Flat Washer

3-3/4" Hex Bolt

Lock Washer

Flat Washer

90°

47-1/4"

79-1/4"

12-5/8"

1 x 5-1/2 x 45-1/8"

Flush

x2

Note hole location.

2953-CC

17

FORT

FRAME BRACING

Align braces with

pre-drilled holes.

Flush

Flat Washer

x4

x1

1 x 3-3/8 x 45-1/8"

3/4 x 3-3/8 x 45-1/8"

x10

x2

Ensure all bracing is

square before installing

wood screws.

Flush

2899-CC

2973-CC

2-1/2"

Wood Screw

BOTTOM

x1

2969-CC

3/4 x 5-3/8 x 45-1/8"

x1

3/4 x 5-3/8 x 45-1/8"

2969-CC

FORT

FRAME BRACING

x2

Align braces with pre-drilled holes.

Flush

2-1/2" Wood Screw

Flush

3-3/4" Hex Bolt

Lock Washer

Flat Washer

x1

2953-CC

3 x 3 x 95"

x1

3/4 x 3-3/8 x 45-1/8"

2973-CC

x1

1 x 3-3/8 x 45-1/8"

2899-CC

Ensure all bracing is square before

installing wood screws.

90°

T-Nut

x2

x4

5" Hex Bolt

x4

x2

BOTTOM

47-1/4"

Lock Nut

Flat Washer

Note hole location.

x1

2954-CC

3 x 3 x 95"

79-1/4"

18

FORT

BOTTOM FRAME BRACE

Align brace with pre-drilled holes.

FLIP ASSEMBLY OVER TO INSTALL BOTTOM BRACE.

Flush

2-1/2"

Wood

Screw

x1

2969-CC

3/4 x 5-3/8 x 45-1/8"

Ensure all bracing is square before

installing wood screws.

90°

x6

FORT

CONNECT FRAME SECTIONS

Align braces with pre-drilled holes.

Lock

Nut

Flat

Washer

ENSURE THESE

HOLES ARE ON

THIS SIDE.

x4

x2

Flat Washer

5" Hex Bolt

2-1/2"

Wood Screw

x20

47-1/4"

La page charge ...

Swing-N-Slide Playsets 4429 Mode d'emploi

Ce manuel convient également à

Swing-N-Slide Playsets 4429 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents