AD31 Reader
• A working internet connection
• A smartphone or laptop
• A #2 Phillips driver (screwdriver or power drill)
• For non-Junction Box install:
• 1/4 inch (6.35mm) drill bit if using wall anchors
• 1/8 inch (3mm) drill bit for pilot holes
• 1/2 inch (12.7mm) drill bit, or larger, for routing
cable through wall
• Wall mount screws & wall anchors (included)
Please note:
To reduce potential safety issues, only use the PoE adapter
provided with the product, a replacement PoE adapter provided by
Verkada, or a PoE adapter purchased as an accessory from Verkada.
What you’ll need AD31 LED Behavior
AD31 Overview
T10 Security
Torx screw
RFID, touch-less access
and status LED interface
Mount plate
Wiring cable
White
Reader is active and ready for secure
badge entrance.
Green
Reader has successfully processed a
user scan.
Red
Reader has identied a negative read.
Re-scan or investigate bad scan.
What’s in the box
1 AD31 Reader 1 Mount plate
2 Wall anchors,
2 wall mount screws &
2 junction box machine
screws (6-32)
1 T10 Security
Torx Allen key
AD31 Mounting
1. Route building-side cable through the circular opening in the
Mount Plate.
2. Secure the Mount Plate to the junction box using 2 provided
machine screws that match the junction box.
3. Connect the wires using the table on the adjacent page as reference.
4. Hook the Reader over the top lip on the mount plate.
5. Secure the Reader to the Mount Plate using the T10 security screw
and Allen key (provided).
1. Using the Mount Plate as your template, mark and drill two holes.
Depending on your mounting surface you may need to drill pilot holes.
If required, insert wall anchors now.
2. Drill ⁄ inch (12.7mm) hole into wall for cable routing if necessary.
3. Route building-side cable through the circular opening in
the Mount Plate.
4. Connect the wires using the table on the adjacent page as reference.
5. Secure the Mount Plate using 2 provided screws.
6. Hook the Reader over the top lip on the Mount Plate.
7. Secure the Reader to the Mount Plate using the T10 security screw
and Allen key (provided).
AD31 Wiring
Once powered on:
Reference the table below for AD31 installation.
Reference the table below for auxiliary Wiegand installation.
Pigtail Color
Orange
Gray
Green
White
Brown
Yellow
Abbreviation
V0
GND
WD0
WD1
LED
BUZZER
Name
Wiegand Voltage
Wiegand Data 1
Wiegand RTN
Wiegand LED
Wiegand Data 0
Wiegand Buzzer
Pigtail Color
Black
Blue
Purple
Red
Abbreviation
-
B
A
+
Name
Ground
RS485-B
RS485-A
+12V IN
• Indicator LEDs (8) will illuminate white during initial power on.
Once 4 white LEDs create a ‘plus’ sign, y ou are ready to scan.
• Scan a physical RFID card to conrm the reader is properly
functioning with the access control system.
• For additional assistance please visit www.verkada.com/support
Support
Thank you for purchasing a Verkada sensor.
If for any reason things don’t work right or you
need assistance, please contact us immediately.
Sincerely,
The Verkada Team
www.verkada.com/support
+1 (650) 514-2500
www.verkada.com/support
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment o and on, the user is
encouraged to try to correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modications not expressly approved by the
party responsible for compliance could void the user’s authority to operate this
equipment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Radiation Exposure Statement:
The product comply with the FCC portable RF exposure limit set forth for an
uncontrolled environment and are safe for intended operation as described in
this manual. The further RF exposure reduction can be achieved if the product
can be kept as far as possible from the user body or set the device to lower
output power if such function is available.
Industry Canada statement
This device complies with ISED’s licence-exempt RSSs. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes : (1) le dispositif ne doit pas produire de brouillage préjudiciable, et
(2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage
susceptible de provoquer un fonctionnement indésirable.
Radiation Exposure Statement:
The product comply with the Canada portable RF exposure limit set forth
for an uncontrolled environment and are safe for intended operation as
described in this manual. The further RF exposure reduction can be achieved
if the product can be kept as far as possible from the user body or set the
device to lower output power if such function is available.
Déclaration d’exposition aux radiations:
Le produit est conforme aux limites d’exposition pour les appareils portables
RF pour les Etats-Unis et le Canada établies pour un environnement non
contrôlé.
Le produit est sûr pour un fonctionnement tel que décrit dans ce manuel.
La réduction aux expositions RF peut être augmentée si l’appareil peut être
conservé aussi loin que possible du corps de l’utilisateur ou que le dispositif
est réglé sur la puissance de sortie la plus faible si une telle fonction est
disponible.
-
1
-
2
-
3
-
4
dans d''autres langues
- English: Verkada AD31 User guide
Documents connexes
Autres documents
-
ALLEGION SM10 Installation Instructions & User Manual
-
Schlage MT15-485 Guide d'installation
-
Axis A1001 Manuel utilisateur
-
HID Global Signo Guide d'installation
-
DoorBird A1121 Series Manuel utilisateur
-
Johnson Controls tyco Kantech T-MUL-MT-KP Manuel utilisateur
-
Farpointe Data CONEKT5 Mode d'emploi
-
Farpointe Data CSR-35 Mode d'emploi
-
Paxton ins-20606 Mode d'emploi
