PROPOINT 8667784 Le manuel du propriétaire
- Catégorie
- Accessoires de moto
- Taper
- Le manuel du propriétaire
V1.2 8667784
Please read and understand all instructions before use. Retain this
manual for future reference.
USER MANUAL
1,000 LB HYDRAULIC/
PNEUMATIC MOTORCYCLE LIFT
8667784 1,000 LB HYDRAULIC/PNEUMATIC MOTORCYCLE LIFT V1.2
2 For technical questions call 1-800-665-8685
SPECIFICATIONS
Material Steel Construction
Lifting Capacity
1,000 lb
Max. Lifting Height 30-1/2 in.
Min. Lifting Height
7 in.
Pump Pressure Range 90 to 120 PSI
Platform Dimensions
26-3/4 x 86-1/2 in.
INTRODUCTION
The 1,000 lb Pneumatic/Hydraulic Motorcycle Lift is a platform
with a wheel chock and removable rear plate specifically designed
to support a motorcycle or dirt bike. Use the lift for cleaning or
vehicle maintenance. Hook the lift up to an air source for quick
lifting or use the anti-slip foot pedal to manually raise the vehicle.
SAFETY
WARNING! Read and understand all instructions before using
this tool. The operator must follow basic precautions to reduce
the risk of personal injury and/or damage to the equipment.
Keep this manual for safety warnings, precautions, operating or
inspection and maintenance instructions.
HAZARD DEFINITIONS
Please familiarize yourself with the hazard notices found in this
manual. A notice is an alert that there is a possibility of property
damage, injury or death if certain instructions are not followed.
1,000 LB HYDRAULIC/
PNEUMATIC MOTORCYCLE LIFT
V1.2 1,000 LB HYDRAULIC/PNEUMATIC MOTORCYCLE LIFT 8667784
Visit www.princessauto.com for more information 3
DANGER! This notice indicates an immediate and specific
hazard that will result in severe personal injury or
death if the proper precautions are not taken.
WARNING! This notice indicates a specific hazard or unsafe
practice that could result in severe personal
injury or death if the proper precautions are not
taken.
CAUTION! This notice indicates a potentially hazardous
situation that may result in minor or moderate
injury if proper practices are not taken.
NOTICE! This notice indicates that a specific hazard or
unsafe practice will result in equipment or
property damage, but not personal injury.
WORK AREA
1. Operate in a safe work environment. Keep your work area
clean, well-lit and free of distractions.
2. Keep anyone not wearing the appropriate safety
equipment away from the work area.
3. Store tools properly in a safe and dry location. Keep tools
out of the reach of children.
PERSONAL SAFETY
WARNING! Wear personal protective equipment approved by
the Canadian Standards Association (CSA) or American
National Standards Institute (ANSI).
PERSONAL PROTECTIVE EQUIPMENT
1. Always wear impact safety goggles that provide front and
side protection for the eyes. Eye protection equipment
should comply with CSA Z94.3-07 or ANSI Z87.1 standards
based on the type of work performed.
2. Wear gloves that provide protection based on the work
materials or to reduce the effects of tool vibration.
8667784 1,000 LB HYDRAULIC/PNEUMATIC MOTORCYCLE LIFT V1.2
4 For technical questions call 1-800-665-8685
2.1 Do not wear gloves when operating a tool that can
snag the material and pull the hand into the tool.
3. Wear protective clothing designed for the work
environment and tool.
4. Non-skid footwear is recommended to maintain footing
and balance in the work environment.
5. Wear steel toe footwear or steel toe caps to prevent a foot
injury from falling objects.
PERSONAL PRECAUTIONS
Control the tool, personal movement and the work
environment to avoid personal injury or damage to the tool.
1. Do not operate any tool when tired or under the influence
of drugs, alcohol or medications.
2. Avoid wearing clothes or jewelry that can become
entangled with the moving parts of a tool. Keep long hair
covered or bound.
3. Do not overreach when operating the tool. Proper footing
and balance enables better control in unexpected situations.
SPECIFIC SAFETY PRECAUTIONS
WARNING! DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence to the
tool safety rules. If you use this tool unsafely or incorrectly,
you can suffer serious personal injury.
1. Use the correct tool for the job. This tool was designed for
a specific function. Do not modify or alter this tool or use it
for an unintended purpose.
2. Always place the tool on a solid, flat, level surface capable
of supporting the weight of the load.
3. Before lowering load, ensure that there are no obstructions
underneath and that all people are standing clear.
V1.2 1,000 LB HYDRAULIC/PNEUMATIC MOTORCYCLE LIFT 8667784
Visit www.princessauto.com for more information 5
4. Do not attempt to move the load while on the lift. The lift
must only be used in a static position for lifting and lowering
loads. Ensure that the load remains stable at all times.
5. Make sure there is enough clearance around the lift and the
load for the movement of raising and lowering.
6. Lower the load slowly to prevent dynamic load shock to
the pump.
7. Do not place your hands between the moving components.
8. Do not place any part of your body beneath the lift while
working on the vehicle.
9. Inspect the tool before each use. DO NOT use if bent,
broken, cracked, leaking or otherwise damaged, any
suspect parts are noticed or it has been subjected to a
shock load.
10. The lift is designed to temporarily support the load. Do not
use for long term support of the load.
11. Follow the precautions for the air source used with the pump.
HYDRAULIC PRECAUTIONS
DANGER! Seek immediate medical attention if hydraulic fluid
under pressure penetrates your skin. See Injection Injury
precautions for instructions before using a pressurized
hydraulic system.
1. Do not touch or handle hydraulic hoses or components
while under pressure. Hydraulic fluid escaping under
pressure has sufficient force to penetrate your clothing and
skin. A pinpoint hole may inject hydraulic fluid into your
body. Seek immediate medical attention if this occurs (see
Injection Injury).
2. Never exceed the hydraulic system’s load capacity
(see Specifications).
3. Do not adjust the hydraulic system’s relief setting. The
settings are preset by the factory.
8667784 1,000 LB HYDRAULIC/PNEUMATIC MOTORCYCLE LIFT V1.2
6 For technical questions call 1-800-665-8685
4. Hydraulic oil under pressure is hot and can cause a burn
injury if touched, sprayed or spilled. Allow the hydraulic
system to cool before conducting maintenance.
5. Hydraulic components require regular inspection. Release
all pressure from the system before you inspect it. Replace
damaged hydraulic parts with identical manufacturer's
components.
6. Do not attempt makeshift repairs to a hydraulic system. Such
repairs can fail suddenly and create a hazardous condition.
7. Hydraulic fluid has a combustible flash point of 200°F
(93°F). Do not expose the fluid to an ignition source.
8. Change your clothing immediately if sprayed with hydraulic
fluid. Store clothing or rags contaminated with hydraulic
fluid in an approved metal safety can with a spring-closing
lid and venting designed to contain a fire.
9. Only use hydraulic fluid in the pump. Do not substitute or
mix brake fluid, or any other fluid, with the hydraulic fluid.
This can result in a pump failure and injure the user or
bystander. It may also damage the pump.
INJECTION INJURY
DANGER! Seek immediate, professional medical treatment if
fluid penetrates your skin. It may feel like a pricking or sting.
Do not wait for the appearance of symptoms. A toxic reaction
can occur from the exposure. Delay in treatment can lead to
amputation or death.
Inform the medical staff that you have a fluid penetration injury
as soon as you arrive at the medical facility. The severity of the
symptoms will depend on the type of fluid injected. Bring the
Safety Data Sheet for the fluid with you to the medical facility
if possible.
V1.2 1,000 LB HYDRAULIC/PNEUMATIC MOTORCYCLE LIFT 8667784
Visit www.princessauto.com for more information 7
INJECTION PRECAUTIONS
Fluid can penetrate the skin at 100 PSI pressure. Fluid escaping
under pressure from the tool has sufficient force to penetrate
your clothing and skin. Follow the precautions below to avoid
an injection injury.
1. Always check for leaks wearing a face shield, safety
goggles, rubberized gloves and protective clothes.
2. Release all pressure from the system before you inspect it.
3. Do not use your hands to detect a fluid leak. Use a large piece
of wood, cardboard or paper and watch for discolouration.
4. Replace damaged parts with identical manufacturer's
components to ensure it is rated to handle the pressure.
UNPACKING
WARNING! Do not operate the tool if any part is missing.
Replace the missing part before operating. Failure to do so
could result in a malfunction and personal injury.
Remove the parts and accessories from the packaging and inspect
for damage.
8667784 1,000 LB HYDRAULIC/PNEUMATIC MOTORCYCLE LIFT V1.2
8 For technical questions call 1-800-665-8685
IDENTIFICATION KEY
A Wheel Rest
B Wheel Chock
C Platform
D Attachment Point
E Ramp
F Front Arm Support
G Safety Bar
H Lock Bolts (x2)
I Caster (x2)
J Pressure Release Pedal
K Foot Pedal
L Air Pump
M Air Hose and Valve
N Hydraulic Pump
O Wheel (x2)
P Rear Arm Support
OPERATION
Letter references in parenthesis (A) refer to the included
Identification Key.
Bleed the hydraulic system before first use and after a long
time in storage (see Care & Maintenance).
1. Lower the platform (C) to the lowest position and check all
nuts and bolts for tightness.
V1.2 1,000 LB HYDRAULIC/PNEUMATIC MOTORCYCLE LIFT 8667784
Visit www.princessauto.com for more information 9
2. Open the release valve on the hydraulic pump (N) and
quickly pump the foot pedal (K) several times to purge air
from the hydraulic system. Close the release valve.
3. Turn the lock bolts (H) until the casters (I) are slightly off the
ground to prevent the lift from rolling. Ensure the lift is level.
4. Tilt the wheel chock (B) so the wheel can easily roll into it.
Push the motorcycle or dirt bike up the ramp (E) onto the
platform (C), then into the wheel chock. Push the wheel
forward until the chock flips forward and the wheel is snug
against the wheel rest.
5. Secure the motorcycle/dirt bike with tie down straps (sold
separately).
6. Repeatedly depress the foot pedal (K) to slowly to raise the
platform. Stop once the table is at the maximum height.
Continuing to increase the pressure can damage the
mechanism or cause a failure in the hydraulic system.
Pressurized air can be used to raise the lift instead of the
foot pedal.
6.1 Ensure the air source pressure does not exceed the
pump’s maximum capacity (see Specifications).
6.2 Attach the valve of the air hose (M) to an air source.
6.3 Press the valve trigger to allow a steady airflow into
the pump. Do not apply air in bursts as this will jolt the
pump and load. This may damage to the lift or cause
the load to shift and fall.
7. Slide the safety bar (G) completely through the holes on
both sides of the front arm support (F). This will prevent
the lift from accidentally descending.
8. When work is complete, remove the safety bar and press the
pressure release pedal (J) and pump the foot pedal (K) to
gently lower the load. Never allow the load to come down
quickly as it can damage the pump or lift’s mechanism.
Ensure the ramp extends correctly.
8667784 1,000 LB HYDRAULIC/PNEUMATIC MOTORCYCLE LIFT V1.2
10 For technical questions call 1-800-665-8685
8.1 Tighten the speed control valve on the hydraulic pump
(N) clockwise to slow the descent speed. Turn the valve
counterclockwise to increase the descent speed.
9. Remove the tie down straps and pull the motorcycle/dirt
bike free of the wheel chock. Walk the vehicle off the
platform and ramp.
10. To store the lift, turn the lock bolts (H) until the casters
touch the ground.
CARE & MAINTENANCE
1. Maintain the tool with care. A tool in good condition is
efficient, easier to control and will have fewer problems.
2. Inspect the tool components periodically. Repair or replace
damaged or worn components. Only use identical
replacement parts when servicing.
3. Follow instructions for lubricating and changing accessories.
4. Keep the tool handles clean, dry and free from oil/grease at
all times.
5. Maintain the tool’s labels and name plates. These carry
important information. If unreadable or missing, contact
Princess Auto Ltd. for replacements.
WARNING! Only qualified service personnel should repair the
tool. An improperly repaired tool may present a hazard to the
user and/or others.
LUBRICATION
Inspect and lubricate the tool when required. Lubricate
mechanical parts of the lift like the foot or release pedal with
heavy oil or grease.
AIR TOOL LUBRICATION
NOTICE! Only use air tool oil to lubricate the pump. Other
lubricants are not suitable and will damage the pump or
cause a malfunction during use.
V1.2 1,000 LB HYDRAULIC/PNEUMATIC MOTORCYCLE LIFT 8667784
Visit www.princessauto.com for more information 11
NOTICE! Never use a penetrating oil to lubricate the pump.
Penetrating oil acts as a solvent that will dissolve the pump’s
grease packing and may damage the o-rings, causing the
pump to seize or malfunction.
1. Manually add a drop or two of air tool oil into the tool’s
male connector before each use and after every hour of
continuous use. Attach the air source and operate for three
seconds to distribute the oil. The tool will not work
properly without lubrication and parts will wear
prematurely.
2. Avoid adding too much air tool oil as this can cause
premature power loss and eventual tool failure. A qualified
technician will need to take the tool apart and clean out the
excess oil.
BLEEDING THE HYDRAULIC SYSTEM
Bleed excess air from the hydraulic system as follows:
1. Open the release valve by depressing the pressure release
pedal (J).
2. Remove the oil filler plug and fill the pump with hydraulic
fluid.
3. Wait 5 minutes for trapped air to rise to the surface.
4. Pump the foot pedal (K) quickly for several full strokes to
eliminate any air in the system. Keep the release valve open.
5. Check the oil filler hole and if necessary, top off with more
hydraulic oil.
6. Restore the oil filler plug. Close the release valve by
restoring the pressure release pedal (J) to its original
position.
7. Test the ram several times for proper operation before
putting it into use. Do not use the ram if it still does not
appear to be working properly. Have a qualified service
technician service or repair the hydraulic system.
8667784 1,000 LB HYDRAULIC/PNEUMATIC MOTORCYCLE LIFT V1.2
12 For technical questions call 1-800-665-8685
STORAGE
When not in use for an extended period, apply a thin coat of
lubricant to the steel parts to avoid rust. Remove the lubricant
before using the tool again.
Lower the lift before storing. Retract the pump’s ram fully to
protect it from corrosion. Extend the lock bolts (H) to raise the
wheels from the ground to prevent it from moving.
DISPOSAL
Recycle a tool damaged beyond repair at the appropriate facility.
Contact your local municipality for a list of disposal facilities or
by-laws for electronic devices, batteries, oil or other toxic liquids.
IMPORTANT! DO NOT pollute the environment by allowing
uncontrolled discharge of waste oil.
DISPOSAL OF HYDRAULIC FLUID
Do not drain hydraulic oil into the sewer system or dispose in
an uncontrolled location. Hydraulic fluid may take up to a year
to break down in the environment and the ingredients may still
be toxic. Contact your local municipality for proper disposal
instructions or locations.
TROUBLESHOOTING
Visit a Princess Auto Ltd. location for a solution if the tool does
not function properly or parts are missing. If unable to do so,
have a qualified technician service the tool.
V1.2 1,000 LB HYDRAULIC/PNEUMATIC MOTORCYCLE LIFT 8667784
Visit www.princessauto.com for more information 13
PROBLEM(S)
POSSIBLE CAUSE(S)
SUGGESTED SOLUTION(S)
Foot pump
does not
work.
Air entering into the
hydraulic system.
Unscrew the vent screw, and
purge the hydraulic system
of trapped air.
Release valve is not
tight.
Tighten the release valve
Lift overloaded. Reduce load (see
Specifications).
Hydraulic system is
contaminated with
particulates.
Service the hydraulic system
and replace hydraulic oil.
Pump does
not work.
The piston and
cylinder seals are
not lubricated or
blocked.
1. Check the cylinder intake
valve for blockage. Add a
small amount of lubricant
to the intake valve before
resealing.
2. Purge the hydraulic
system of air.
Pump pressure is
insufficient.
Increase the air pressure to
the pump, but ensure it does
not exceed the maximum
pressure rating (see
Specifications).
Release valve is not
tight.
Tighten the release valve.
Hydraulic system is
contaminated with
particulates.
Service the hydraulic system
and replace hydraulic oil.
Platform
doesn’t raise
to maximum
height.
Insufficient
hydraulic oil in the
cylinder.
Add hydraulic oil until
cylinder is full. Purge air from
the hydraulic system, then
top up the oil.
8667784 1,000 LB HYDRAULIC/PNEUMATIC MOTORCYCLE LIFT V1.2
14 For technical questions call 1-800-665-8685
PARTS BREAKDOWN
V1.2 1,000 LB HYDRAULIC/PNEUMATIC MOTORCYCLE LIFT 8667784
Visit www.princessauto.com for more information 15
PARTS LIST
#
DESCRIPTION
QTY
1
Bolt M10×25
8
2
Front Arm Support
1
3
Washer Ø12
16
4
Washer Ø10
2
5
Spring Washer Ø10
2
6 Nut M10 2
7
Support
2
8
Adjusting Screw
2
9
Washer Ø6
2
10
Nut M6
2
11
Universal Wheel
2
12
Washer Ø8
4
13
Bolt M8×18
1
14
Release Valve Spindle
1
15
Release Foot Pedal
1
16
Pump Foot Pedal
Spindle
1
17
Pump Seat
2
18
pump Foot Pedal
1
19
Spring
1
20
Pump Connecting
Rod
1
21
Pin
8
22
Retainer Ring Ø12
16
23
Wheel
2
24
Washer Ø14
2
25
Retainer Ring Ø14
2
26
Washer Ø10
8
27
Spring Washer Ø10
8
28
Frame assembly
1
29
Nut M10
6
30
Bolt M8X30
4
31
Release Connecting
Rod
1
32
Nut M8
4
33
Rear Arm Support
1
34
Shaft
1
35
Washer Ø20
2
36
Retainer Ring Ø20
2
37
Bolt M10×10
1
38
Pump Head
Component
1
39
Pump
1
40
Ramp
1
41
Moveable Plate
1
42
Platform
1
43
Elastic Cylindrical Pin
1
44
Safety Bar
1
45
Spring Washer Ø8
1
46
Spindle
1
47
Bolt M8X20
12
48
Washer Ø8
6
49
Track
2
50
Bolt M10X20
2
51
Spring Washer Ø10
2
52
Washer Ø10
1
53
Rubber Plug
1
54
Dam-board
1
55
Clamp Frame
1
56
Movable Frame
1
57
R-pin
1
58
Ring
1
V 1,2 8667784
Vous devez lire et comprendre toutes les instructions avant d'utiliser
l'appareil. Conservez ce manuel afin de pouvoir le consulter plus tard.
MANUEL D'UTILISATEUR
PONT-ÉLÉVATEUR POUR
MOTOCYCLETTES HYDRAULIQUE/
PNEUMATIQUE, 1 000 LB
8667784 PONT-ÉLÉVATEUR POUR MOTOCYCLETTES V 1,2
HYDRAULIQUE/PNEUMATIQUE, 1 000 LB
2 En cas de questions techniques, appelez le 1-800-665-8685
SPÉCIFICATIONS
Matériau Construction en acier
Capacité de levage 1 000 lb
Hauteur de soulèvement max. 30 1/2 po
Hauteur de levage min.
7 po
Plage de pression de la pompe 90 à 120 lb/po carré
Dimensions de plate-forme
26 3/4 à 86 1/2 po
INTRODUCTION
Le pont-élévateur pneumatique/hydraulique d’une capacité de
1 000 lb pour motocyclettes est une plate-forme munie d’une
cale de roue et d’une plaque arrière amovible conçue pour
soutenir une motocyclette ou une moto hors route. Utilisez le
pont-élévateur afin de procéder au nettoyage ou à l’entretien
du véhicule. Accrochez le pont-élévateur en position soulevée
pour procéder à un levage rapide ou utilisez la pédale
antidérapante pour soulever manuellement le véhicule.
SÉCURITÉ
AVERTISSEMENT ! Veuillez lire et comprendre toutes les
instructions avant d'utiliser cet outil. L'utilisateur doit respecter
les précautions de base lorsqu'il utilise cet outil afin de réduire
le risque de blessure ou de dommage à l'équipement.
PONT-ÉLÉVATEUR POUR
MOTOCYCLETTES HYDRAULIQUE/
PNEUMATIQUE, 1 000 LB
V 1,2 PONT-ÉLÉVATEUR POUR MOTOCYCLETTES 8667784
HYDRAULIQUE/PNEUMATIQUE, 1 000 LB
Visitez www.princessauto.com pour plus d'informations 3
Conservez ce manuel qui contient les avertissements de
sécurité, les précautions, les instructions de fonctionnement ou
d'inspection et d'entretien.
DÉFINITIONS DE DANGER
Veuillez-vous familiariser avec les avis de danger qui sont
présentés dans ce manuel. Un avis est une alerte indiquant qu'il
existe un risque de dommage à la propriété, de blessure ou de
décès si on ne respecte pas certaines instructions.
DANGER ! Cet avis indique un risque immédiat et
particulier qui entraînera des blessures
corporelles graves ou même la mort si on
omet de prendre les précautions
nécessaires.
AVERTISSEMENT ! Cet avis indique un risque particulier ou une
pratique non sécuritaire qui pourrait
entraîner des blessures corporelles graves
ou même la mort si on omet de prendre les
précautions nécessaires.
ATTENTION ! Cet avis indique une situation possiblement
dangereuse qui peut entraîner des blessures
mineures ou modérées si on ne procède pas
de la façon recommandée.
AVIS ! Cet avis indique un risque particulier ou une
pratique non sécuritaire qui entraînera des
dommages au niveau de l'équipement ou
des biens, mais non des blessures
corporelles.
AIRE DE TRAVAIL
1. Travaillez dans un environnement de travail sécuritaire.
Gardez votre aire de travail propre, bien éclairée et
exempte de toute distraction.
8667784 PONT-ÉLÉVATEUR POUR MOTOCYCLETTES V 1,2
HYDRAULIQUE/PNEUMATIQUE, 1 000 LB
4 En cas de questions techniques, appelez le 1-800-665-8685
2. Assurez-vous que les personnes qui ne portent pas
l'équipement de sécurité approprié ne se trouvent pas à
proximité de l'aire de travail.
3. Rangez les outils correctement dans un lieu sécurisé et sec.
Gardez les outils hors de la portée des enfants.
SÉCURITÉ PERSONNELLE
AVERTISSEMENT ! Portez de l'équipement de protection
personnelle homologué par l'Association canadienne de
normalisation (CSA) ou l'American National Standards
Institute (ANSI).
ÉQUIPEMENT DE PROTECTION PERSONNELLE
1. Portez toujours des lunettes antiprojections qui offrent une
protection frontale et latérale pour les yeux. L'équipement de
protection des yeux devrait être conforme à la norme CSA
Z94.3-07 ou ANSI Z87.1 fonction du type de travail effectué.
2. Portez des gants qui protègent en fonction des matériaux
de travail et pour réduire les effets des vibrations de l'outil.
2.1 Ne portez pas de gants lorsque vous utilisez un outil
dans lequel le tissu pourrait demeurer coincé,
entraînant ainsi la main.
3. Portez des vêtements de protection conçus pour
l'environnement de travail et pour l'outil.
4. Les chaussures antidérapantes sont recommandées pour
maintenir la stabilité et l'équilibre au sein de
l'environnement de travail.
5. Portez des chaussures à embout d'acier ou à coquilles d'acier
pour éviter les blessures aux pieds dues à la chute d'objets.
PRÉCAUTIONS PERSONNELLES
Gardez le contrôle de l'outil, de vos mouvements et de
l'environnement de travail pour éviter les blessures ou le bris
de l'outil.
V 1,2 PONT-ÉLÉVATEUR POUR MOTOCYCLETTES 8667784
HYDRAULIQUE/PNEUMATIQUE, 1 000 LB
Visitez www.princessauto.com pour plus d'informations 5
1. N'utilisez pas l'outil si vous êtes fatigué ou sous l'effet de
drogues, d'alcool ou de médicaments.
2. Évitez de porter des vêtements ou des bijoux pouvant se
prendre dans les pièces mobiles d'un outil. Gardez les
cheveux longs recouverts ou attachés.
3. N'utilisez pas l'outil si vous devez étirer les bras pour vous
en servir. Une stabilité et un équilibre appropriés sont
nécessaires afin d'avoir un meilleur contrôle en cas de
situations inattendues.
CONSIGNES DE SÉCURITÉ SPÉCIFIQUES
AVERTISSEMENT ! Ne permettez PAS au confort ou à votre
familiarisation avec l'outil (obtenus après un emploi répété) de
se substituer à une adhésion stricte aux règles de sécurité de
l'outil. Si vous utilisez cet outil de façon dangereuse ou
incorrecte, vous pouvez subir des blessures corporelles graves.
1. Utilisez le bon outil pour la tâche à effectuer. Cet outil a été
conçu pour une utilisation spécifique. Évitez de modifier ou
d'altérer cet outil ou de l'utiliser à une fin autre que celle
pour laquelle il a été conçu.
2. Placez toujours l'outil sur une surface solide, plane et au
niveau capable de soutenir le poids de la charge.
3. Avant d'abaisser la charge, assurez-vous qu'aucune
obstruction ne se trouve en dessous et que tous les gens se
trouvent à l'écart.
4. Ne tentez pas de déplacer la charge alors qu’elle se trouve
sur le pont-élévateur. Le pont-élévateur doit être utilisé en
position immobile afin de pouvoir soulever et abaisser des
charges. Assurez-vous que la charge demeure stable en
tout temps.
5. Assurez-vous qu’il existe un jeu suffisant autour du pont-
élévateur et de la charge afin de permettre le mouvement.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
PROPOINT 8667784 Le manuel du propriétaire
- Catégorie
- Accessoires de moto
- Taper
- Le manuel du propriétaire
dans d''autres langues
- English: PROPOINT 8667784 Owner's manual
Documents connexes
Autres documents
-
Powerfist 9105388 Le manuel du propriétaire
-
-
Power Fist 8667792 Le manuel du propriétaire
-
-
-
-
-
-
-