PROPOINT 9081548 Le manuel du propriétaire

Marque: PROPOINT

Modèle: 9081548

Taper: Le manuel du propriétaire

V1.0 9081548

Please read and understand all instructions before use. Retain this manual for future reference.

SHOP PRESS



PNEUMATIC/HYDRAULIC

This page is intentionally left blank.

SPECIFICATIONS

Press Capacity 40,000 lb

Press Type Pneumatic/hydraulic

Ram Travel 6 in.

Working Range 3-5/16 to 18-1/8 in.

Bed Width 19-11/16 in.

Overall Height 39-13/16 in.

Pressure Rating 110 to 120 PSI

Material Steel Construction

INTRODUCTION

The workshop press is designed for light industrial use or for home

use. Perform straightening, stamping and bending with this powerful

hydraulic press. Features an H-frame design that makes it perfect for

removing or installing bearings, bushings, gears, ball joints, pulleys,

universal joints and more.

The press features a pneumatic foot control .

SAFETY

WARNING! Read and understand all instructions before

using this tool. The operator must follow basic precautions

to reduce the risk of personal injury and/or damage to the

equipment.

HAZARD DEFINITIONS

Please familiarize yourself with the hazard notices found in this manual.

A notice is an alert that there is a possibility of property damage, injury

or death if certain instructions are not followed.

DANGER! This notice indicates an immediate and specific hazard that will

result in severe personal injury or death if the proper precautions

are not taken.

WARNING! This notice indicates a specific hazard or unsafe practice that could

result in a serious injury if the proper precautions are not taken.

V1.0 PNEUMATIC/HYDRAULIC SHOP PRESS 9081548

Page 3 Assistance available at www.princessauto.com or 1-800-665-8685

CAUTION! This notice indicates a potentially hazardous situation that may

result in minor or moderate injury if proper practices are not taken.

NOTICE! This notice indicates that a specific hazard or unsafe practice will

result in equipment or property damage, but not personal injury.

WORK AREA

1. Operate in a safe work environment. Keep your work area clean,

well-lit and free of distractions. Place lights so you are not working

in a shadow.

2. Keep anyone not wearing the appropriate safety equipment away

from the work area.

3. Store unused tools properly in a dry, safe and secure location to

prevent rust, damage or misuse.

PERSONAL SAFETY

WARNING! Wear personal protective equipment approved

by the Canadian Standards Association (CSA) or American

National Standards Institute (ANSI).

PERSONAL PROTECTIVE EQUIPMENT

1. Always wear impact safety goggles that provide front and side

protection for the eyes. Eye protection equipment should comply

with CSA Z94.3-07 or ANSI Z87.1 standards based on the type of

work performed.

2. Wear the appropriate type of full-face shield in addition to safety

googles, as the work can create chips, abrasive or particulate

matter.

3. Wear protective clothing and gloves designed for the work

environment, materials and tools.

4. Wear steel toe footwear or steel toe caps to prevent a foot injury

from falling objects.

5. The tool may contain high pressure. Use safety glasses and gloves

for protection during operation. Keep hands clear of the exposed

rubber portions of the hose.

6. The air source used with this tool may cause hearing damage.

Wear ear protection gear to eliminate or reduce the noise.

9081548 PNEUMATIC/HYDRAULIC SHOP PRESS V1.0

Assistance available at www.princessauto.com or 1-800-665-8685 Page 4

PERSONAL PRECAUTIONS

Control the tool, personal movement and the work environment to avoid

personal injury or damage to tool.

1. Do not operate any tool when tired or under the influence of drugs,

alcohol or medications.

2. Avoid wearing clothes or jewelry that can become entangled with

the moving parts of a tool. Keep long hair covered or bound.

3. Avoid unintentional starts. Be sure that the regulator/throttle switch

is in the neutral or OFF position when not in use and before

connecting it to any air source.

4. Never point the air stream or tool at any point of your body, other

people or animals. Debris and dust ejected at high speed can

cause an injury.

5. Serious injury or death may occur from inhaling compressed air.

The air stream may contain carbon monoxide, toxic vapors or solid

particles. Never inhale compressed air directly from the pump or

air tool.

SPECIFIC SAFETY

WARNING! DO NOT let comfort or familiarity with product

(gained from repeated use) replace strict adherence to the

tool safety rules. If you use this tool unsafely or incorrectly,

you can suffer serious personal injury.

1. Use the correct tool for the job. This tool was designed for a

specific function. Do not modify or alter this tool or use it for an

unintended purpose.

2. The maximum load is 20 tons. Do not exceed this rated capacity.

Never apply excessive force to a workpiece and always use the

pressure gauge to accurately determine the applied load.

3. Inspect the press before each use. Do not use if any component

is bent, broken, cracked, leaking or showing other damage. Do not

use the press after a shock load until a qualified technician has

examined the press.

4. Check to ensure that all bolts and nuts are tight.

V1.0 PNEUMATIC/HYDRAULIC SHOP PRESS 9081548

Page 5 Assistance available at www.princessauto.com or 1-800-665-8685

5. Only use this shop press on a surface that is stable, level and not

slippery. The surface must be capable of sustaining the weight of

the shop press and the load.

6. Ensure that the workpiece is center-loaded and secure. An

unbalanced load may slip off the heel blocks or bed frame.

7. Keep hands and feet away from the bed frame area at all times.

8. Do not use the shop press to compress a spring or any other item

that could disengage and cause a potential hazard. Never stand

directly in front of a loaded press and never leave a loaded press

unattended.

9. Do not allow an untrained person to operate the press.

10. Do not use brake fluid or other improper fluid in place of hydraulic

oil. Avoid mixing different types of oil when adding hydraulic oil.

Only good quality hydraulic jack oil can be used.

11. Do not expose the press to rain, snow or inclement weather.

12. Bolt the press to the floor if it is to be used on bulky or

unstable items.

POWER TOOL PRECAUTIONS

1. Do not use any power tool with a malfunctioning power switch

or control. A power tool that fails to respond to the controls is

dangerous and can cause an injury. A qualified technician must

repair and verify the power tool is operating correctly, before it can

be used.

2. Shut the power off and disconnect the press from the power

supply (if possible) before making any adjustments, changing

accessories, cleaning, servicing or when storing. Such preventive

safety measures reduce the risk of starting the tool accidentally.

3. Check if the press's moving parts are misaligned or binding before

each use. Correct the issue before using the press to avoid an

injury or damage to the tool.

4. Avoid unintentional starts. Be sure that the regulator/throttle switch

is in the neutral or OFF position when not in use and before

connecting it to any air source.

9081548 PNEUMATIC/HYDRAULIC SHOP PRESS V1.0

Assistance available at www.princessauto.com or 1-800-665-8685 Page 6

HYDRAULIC PRECAUTIONS

DANGER! Seek immediate medical attention if hydraulic

fluid under pressure penetrates your skin. See Injection

Injury precautions for instructions before using a

pressurized hydraulic system.

1. Do not touch or handle, hydraulic hoses or components while

under pressure. Hydraulic fluid escaping under pressure has

sufficient force to penetrate your clothing and skin. A pinpoint hole

may inject hydraulic fluid into your body. Seek immediate medical

attention if this occurs (see Injection Injury).

2. Never exceed the hydraulic system’s load capacity (see

Specifications).

3. Do not adjust the hydraulic system’s relief setting. The settings are

preset by the factory.

4. Hydraulic oil under pressure is hot and can cause a burn injury

if touched, sprayed or spilled. Allow the hydraulic system to cool

before conducting maintenance.

5. Hydraulic components require regular inspection. Release all

pressure from the system before you inspect it. Replace damaged

hydraulic parts with identical manufacturer's components.

6. Do not attempt makeshift repairs to a hydraulic system. Such

repairs can fail suddenly and create a hazardous condition.

7. A damaged or disconnected hydraulic hose under pressure may

whip around and inflict personal injury or damage the work area.

Secure the hose to a fixed or permanent structure with clamps or

cable ties.

8. Hydraulic fluid has a combustible flash point of 200°F (93°F). Do

not expose the fluid to an ignition source.

9. Change your clothing immediately if sprayed with hydraulic fluid.

Store clothing or rags contaminated with hydraulic fluid in an

approved metal safety can with a spring-closing lid and venting

designed to contain a fire.

10. Only use hydraulic fluid in the pump. Do not substitute or mix

brake fluid, or any other fluid, with the hydraulic fluid. This can

V1.0 PNEUMATIC/HYDRAULIC SHOP PRESS 9081548

Page 7 Assistance available at www.princessauto.com or 1-800-665-8685

result in a pump failure and injure the user or bystander. It may

also damage the pump.

INJECTION INJURY

DANGER! Seek immediate, professional medical treatment

if fluid penetrates your skin. It may feel like a pricking or

sting. Do not wait for the appearance of symptoms. A toxic

reaction can occur from the exposure. Delay in treatment

can lead to amputation or death.

Inform the medical staff that you have a fluid penetration injury as soon

as you arrive at the medical facility. The severity of the symptoms will

depend on the type of fluid injected. Bring the Safety Data Sheet for the

fluid with you to the medical facility if possible.

INJECTION PRECAUTIONS

Fluid can penetrate the skin at 100 PSI pressure. Fluid escaping under

pressure from the tool has sufficient force to penetrate your clothing

and skin. Follow the precautions below to avoid an injection injury.

1. Always check for leaks wearing a face shield, safety goggles,

rubberized gloves and protective clothes.

2. Release all pressure from the system before you inspect it.

3. Do not use your hands to detect a leak. Use a large piece of wood,

cardboard or paper and watch for discolouration.

4. Replace damaged parts with identical manufacturer's components

to ensure it is rated to handle the pressure.

AIR TOOL PRECAUTIONS

1. Use only clean and dry compressed air as a power source.

Contaminated or moist air will gradually damage the tool.

2. Install an in-line shutoff valve or regulator to allow immediate

control over the air supply in an emergency, even if a hose is

ruptured.

3. Discontinue tool use if it does not work properly or air is leaking.

Tag or mark the tool as ‘defective’ or ‘out of service’ until repaired.

4. Check the manufacturer’s maximum pressure rating for air tools

and accessories. Compressor outlet pressure must be regulated

9081548 PNEUMATIC/HYDRAULIC SHOP PRESS V1.0

Assistance available at www.princessauto.com or 1-800-665-8685 Page 8

to never exceed the maximum pressure rating of the tool (see

Specifications). Exceeding the maximum PSI rating can create a

bursting hazard, causing injury and property damage.

a. The tool does not regulate the pressure level. The power

output is in direct proportion to the air pressure available. An

external air pressure regulator is required to safely use this

tool.

5. Never use oxygen, combustible gas or any other bottled gas as

a power source. Any power source other than an air compressor

could cause an explosion and serious personal injury.

6. Turn OFF the valve and discharge any remaining air pressure after

each use or before adjusting the tool.

7. Do not leave the air tool unattended with its compressed air supply

on. Turn off the compressed air supply and bleed the air tool of any

remaining compressed air before leaving the air tool unattended.

8. Serious injury may occur from loose debris being propelled at

high speeds from the compressed air stream. Always wear OSHA

approved safety glasses to protect the eyes during operation of the

air compressor.

9. Always turn off the air compressor and drain tank pressure

completely before attempting maintenance or attaching air tools.

Release pressure slowly from the system.

10. Do not cover the air vents.

AIR HOSE PRECAUTIONS

1. Inspect the tool's air hose for cracks, fraying or other faults before

each use. Discontinue use if the air hose is damaged or hissing

is heard from the air hose or couplers. Replace the defective air

hose.

2. Do not allow people, mobile equipment or vehicles to pass over the

unprotected air hose. Position the air hose away from high traffic

areas, in a reinforced conduit or place planks on both sides of the

air hose to create a protective trench.

3. Prevent damage to the air hose by observing the following:

a. Keep the air hose behind the tool and out of the tool's work

path.

V1.0 PNEUMATIC/HYDRAULIC SHOP PRESS 9081548

Page 9 Assistance available at www.princessauto.com or 1-800-665-8685

b. Keep the air hose away from heat, oil, sharp edges or moving

parts.

c. Do not wrap the air hose around the tool as sharp edges may

pierce or crack the air hose. Gently coil the hose and either

hang on a hook or fasten with a device to keep hose together

when storing.

4. A damaged or disconnected air hose under pressure may whip

around and inflict personal injury or damage the work area. Secure

the compressor's air hose to a fixed or permanent structure with

clamps or cable ties.

UNPACKING

WARNING! Do not operate the tool if any part is missing.

Replace the missing part before operating. Failure to do so

could result in a malfunction and personal injury.

Remove the parts and accessories from the packaging and inspect for

damage.

ASSEMBLY & INSTALLATION

INSTALL AN AIR COUPLER PLUG

Prepare a standard 1/4 in. NPT coupler plug (sold separately) for use

with your tool.

1. Wrap the external threads of the coupler plug with sealant tape.

a. Wrap tape in a clockwise direction so it will not unravel.

b. Do not tape all the threads. Leave several leading threads

unwrapped for easier alignment.

2. Screw the coupler plug into the tool's air inlet and tighten with a

wrench until snug.

3. Run the compressor at a low volume and check the connection for

air leaks. Do not use the tool until all air leaks are repaired or the

faulty component is replaced.

9081548 PNEUMATIC/HYDRAULIC SHOP PRESS V1.0

Assistance available at www.princessauto.com or 1-800-665-8685 Page 10

IMPORTANT! Vibration may cause failure if a quick coupler

is connected directly to the air tool. To overcome this,

connect a leader hose to the tool. A quick coupler may then

be used to connect the leader hose to the air line hose.

ASSEMBLY

Consult the parts list as necessary during assembly.

1. Position the frame (#1) vertically on a flat surface. Check that

mounting plate for the pump is on the right side.

2. Insert an M10x30 bolt (#2) through each bolt hole on the frame's

bottom from the inside. Do not secure yet.

3. Position one base (#4) over the protruding bolts. Secure each

M10x30 bolt with a M10 washer (#5), M10 lock washer (#6) and

M10 nut (#7) until hand-tight.

4. Repeat on the other side.

5. Secure a strut (#3) to each end of a base with an M10x30 bolt,

M10 washer, M10 lock washer and M10 nut until hand-tight.

6. Secure the free end of each strut to the second set of bolt holes

from the bottom with an M10x30 bolt, M10 washer, M10 lock

washer and M10 nut.

7. Screw the pressure gauge (#21) and o-ring (#24) into the

connection nut (#25) of the three-way valve block (#23) through

the hole on the upper beam.

8. Connect one end of the long hydraulic hose (#15) to the 90°

connection nut (#27) on the end of the three-way valve block.

9. Secure the pump with M10x15 bolts (#17) and M10 washers. The

bolts are inserted through the right post and into screw holes in the

pump’s mounting frame.

10. Connect the other end of the long hydraulic hose (#15) to the

pump's connection nut.

11. Thread the upper round nut (#30) onto the ram until it reaches the

top threads.

12. Slide the ram through the opening in the cylinder base plate until

the upper round nut is sitting on top of the plate.

V1.0 PNEUMATIC/HYDRAULIC SHOP PRESS 9081548

Page 11 Assistance available at www.princessauto.com or 1-800-665-8685

13. Thread the lower round nut (#18) onto the ram from beneath and

tighten to secure the ram to the cylinder base plate.

14. Connect the short hydraulic hose (#32) to the ram cylinder's

connection nut. Connect the other end to the 90° connection nut

(#27) on the three-way valve block.

15. Connect the air pump's hose to the outlet port of the foot air valve.

• Follow the instructions for wrapping the threads with sealant

tape in Install an Air Coupler Plug.

16. Push each bed frame pin (#36) through the matching set of holes

on the left and right side of the frame. The bed frame will rest on

these, so ensure they are level with each other. Secure the pins

with the included clips (#37).

17. Position the bed frame so the beams are outside of the leg

assemblies. Lower until the bed frame is resting on the pins.

18. Install the rollers. Slide an M10 washer (#A7) onto an M10x35 bolt

(#A11), then a roller bushing (#A12) and a short bushing (#A13).

Screw the bolt into one of the inner bolt holes on the bed frame's

face. Repeat for the other 3 rollers.

19. Place an M10 washer (#A7) onto an M10x50 bolt (#A6) and insert

it in the top bolt hole of the left adjusting base. Place another M10

washer, then a bushing onto the protruding bolt. Prepare a second

bolt in the same manner.

20. Position the left adjusting base (#A8) with the angled side to the

outside and the knob (#A10) on the inside. Screw the bolt into

the upper outer bolt hole on the bed frame's left side. Screw the

second bolt into the lower bolt hole.

21. Repeat steps 18 and 19 with the right adjusting base.

22. Place the screen handle (#A1) on the screen and align the bolt

holes. Insert an M6x20 bolt (#A4) through each bolt hole. Secure

each with an M6 washer (#A2) and M6 nut (#A3).

23. Slide the screen into place between the rollers until the height is

appropriate to protect the user during the task. Tighten the two

adjusting base knobs to hold the screen in place.

24. Insert the handle (#11) into the pump receiver for manual

operation.

9081548 PNEUMATIC/HYDRAULIC SHOP PRESS V1.0

Assistance available at www.princessauto.com or 1-800-665-8685 Page 12

25. Check all bolts and nuts and tighten if necessary.

OPERATIONS

BEFORE FIRST USE

Before the first use, check for proper hydraulic oil level in the system.

Then thoroughly test the hydraulic ram for proper operation prior to its

actual use.

1. Purge air from the hydraulic system. See Bleeding the Hydraulic

System in the Maintenance section.

2. Test the shop press without a workpiece to ensure all parts work

smoothly. Test again with a load. Gradually increase pressure and

watch that the workload does not shift and there is no distortion or

deflection of the ram, leakage from the pump assembly or shifting

of the frame. A qualified technician should examine and repair any

problems with the pump itself.

PRESSURE DROP

Apply the air consumption and pressure rate numbers to the tool’s

air inlet, not the compressor’s outlet. Calculate the pressure drop for

your air supply set-up and increase the compressor outlet pressure to

compensate. Make sure you do not exceed the maximum pressure for

any part of your air supply system.

Installing a pressure gauge at the tool inlet is the best way to measure

the air pressure and adjust the compressor’s output.

OPERATING THE PRESS

IMPORTANT! Ensure that you read, understand and apply

the safety instructions and warnings before use.

Manually add a drop or two of air tool oil into the tool’s coupler plug

before each use and after every hour of continuous use. The tool will

not work properly without lubrication and parts will wear prematurely.

1. Lift or lower the bed frame (#34) until it is in position. Insert a bed

frame pin (#36) into the left and right posts beneath the bed frame.

Lower the bed frame so it rests on the bed frame pins.

V1.0 PNEUMATIC/HYDRAULIC SHOP PRESS 9081548

Page 13 Assistance available at www.princessauto.com or 1-800-665-8685

2. Place the heel blocks (#35) on the bed frame, then insert a

workpiece on the heel blocks.

• Tapping the elastic cylinder pins out on the heel block's

corners can help hold them in position during the task

3. Close the release valve (#13) on the pump by turning it clockwise.

4. Pump the handle or pedal until the ram nears the workpiece.

5. Align the workpiece and ram to ensure center-loading.

6. Pump the handle or pedal to apply load onto the workpiece.

7. Do not exceed the maximum piston stroke. If you see a red line

on the piston, retract the ram and adjust the bed to bring the

workpiece closer to the ram.

8. Stop applying load to the workpiece when the task is complete.

9. Slowly and carefully remove load from workpiece by turning the

release valve counterclockwise in small increments.

10. Once the ram has fully retracted, remove the workpiece from the

bed frame.

11. Close the release valve when you have finished for the day.

CARE & MAINTENANCE

1. Maintain the tool with care. A tool in good condition is efficient,

easier to control and will have fewer problems.

2. Inspect the tool components periodically. Repair or replace

damaged or worn components. Only use identical replacement

parts when servicing.

3. Only use accessories intended for use with this tool. Follow

instructions for changing accessories.

4. Keep the tool handles or gripping surfaces clean and dry.

5. Maintain the tool’s labels and name plates. These carry important

information. If unreadable or missing, contact Princess Auto Ltd.

for replacements.

WARNING! Only qualified service personnel should repair

the tool. An improperly repaired tool may present a hazard

to the user and/or others.

9081548 PNEUMATIC/HYDRAULIC SHOP PRESS V1.0

Assistance available at www.princessauto.com or 1-800-665-8685 Page 14

HYDRAULIC RAM MAINTENANCE

Monthly maintenance is recommended for the hydraulic ram. Any

restrictions due to dirt, rust, etc. can cause the either slow movement or

extremely rapid jerks, damaging the internal components. The following

steps are designed to keep the pump maintained and operational.

1. Lubricate the cylinder and the pumping mechanism with light oil.

2. Visually inspect for cracked welds, bent, loose, missing parts or

hydraulic oil leaks.

3. Inspect the hydraulic ram immediately if it was subjected to an

abnormal load or shock load.

4. Remove any hydraulic jack pump from service that is damaged,

worn down or operates abnormally, until repaired by an authorized

service technician.

5. Check and maintain the ram oil level.

6. Always store the hydraulic ram in the fully retracted position. This

will help protect critical areas from corrosion.

7. Do not use brake or transmission fluids or regular motor oil as they

can damage the seals. Always purchase and use products labeled

Hydraulic Oil.

REPLACE THE HYDRAULIC OIL

Replace the hydraulic oil annually.

The oil can be removed by using a fluid extractor tool or detaching the

from the press and manually emptying it.

FLUID EXTRACTOR TOOL

1. Retract the ram and remove the oil filler plug.

2. Follow the instructions for your fluid extractor tool to remove the old

hydraulic oil.

3. Follow the instructions for Refill the.

MANUAL OIL REPLACEMENT

1. Relieve pressure from the system by loosening the oil filler plug.

2. Remove the from the press.

V1.0 PNEUMATIC/HYDRAULIC SHOP PRESS 9081548

Page 15 Assistance available at www.princessauto.com or 1-800-665-8685

3. Remove the oil fill plug.

4. Lay the on its side and drain the oil into a suitable container.

Dispose of used hydraulic oil in accordance with local by-laws.

5. Stand the on its base and wipe off any excess oil.

6. Reinstall the hydraulic onto the press.

7. Follow the instructions for Refill the.

REFILL THE HYDRAULIC JACK PUMP

The pump may become less efficient when the hydraulic oil level is too

low or contaminated by metal particulate through normal wear-and-tear.

1. Retract the ram and remove the oil filler plug.

2. Check and maintain the ram oil level.

• Check the oil level with the oil dip stick. Use a long plastic

cable tie as a substitute if the unit does not have a dipstick.

3. Fill the cylinder with a high quality hydraulic jack oil, up to the oil

plug opening.

a. Place a funnel into the oil fill neck. The funnel opening should

be wide enough to prevent the oil from collecting in the

funnel’s cone.

b. Pour oil into the funnel. Allow the oil to settle for one minute

and recheck the level. Repeat until the desired level is

reached.

4. Follow the steps in Bleeding the Hydraulic System.

5. Insert the oil filler plug and hand tighten.

6. Wipe up any spilled oil. Dispose of oil soaked rags in a proper

hazardous waste container.

BLEEDING THE HYDRAULIC SYSTEM

Bleed excess air from the hydraulic system as follows:

1. Open the release valve by turning it counterclockwise.

2. Remove the oil filler screw and fill the hydraulic jack pump with

hydraulic fluid.

3. Wait 5 minutes for trapped air to rise to the surface.

9081548 PNEUMATIC/HYDRAULIC SHOP PRESS V1.0

Assistance available at www.princessauto.com or 1-800-665-8685 Page 16

4. Pump the handle or pedal for several strokes or press the air valve

trigger to eliminate any air in the system.

5. Check the oil filler hole and if necessary, top off with more

hydraulic oil.

6. Restore the oil filler screw. Close the release valve by turning

clockwise.

7. Test the ram several times for proper operation before putting it

into use. Do not use the ram if it still does not appear to be working

properly. Have a qualified service technician service or repair the

hydraulic system.

LUBRICATION

Inspect and lubricate the tool when required. Only use light oil to

lubricate the tool. Other lubricants may not be suitable and could

damage the tool or cause a malfunction during use.

Clean and lubricate all moving parts.

AIR TOOL LUBRICATION

NOTICE! Only use air tool oil to lubricate the tool. Other

lubricants are not suitable and will damage the tool or cause

a malfunction during use.

NOTICE! Never use a penetrating oil to lubricate an air tool.

Penetrating oil acts as a solvent that will dissolve the tool’s

grease packing and may damage the o-rings, causing the

tool to seize or malfunction.

1. All air tools have an internal coating of grease to prevent corrosion

during shipping and storage. Remove this grease by adding a

generous amount of air tool oil in the air inlet and then run the tool

under no load until the exhaust is clear.

2. Manually add a drop or two of air tool oil into the tool’s coupler

plug before each use and after every hour of continuous use. The

tool will not work properly without lubrication and parts will wear

prematurely.

V1.0 PNEUMATIC/HYDRAULIC SHOP PRESS 9081548

Page 17 Assistance available at www.princessauto.com or 1-800-665-8685

3. Avoid adding too much air tool oil as this can cause premature

power loss and eventual tool failure. A qualified technician will

need to take the tool apart and clean out the excess oil.

4. Apply a generous amount of air tool oil to the tool before storing

it for an extended period of time (overnight, weekend, etc.). Run

the tool for approximately 30 seconds to ensure the oil is evenly

distributed throughout the tool. Store it in a clean and dry location.

STORAGE

When not in use, store the press in a dry location with ram and piston

fully retracted.

DISPOSAL

Recycle a tool damaged beyond repair at the appropriate facility.

Contact your local municipality for a list of disposal facilities or by-laws

for electronic devices, batteries, oil or other toxic liquids.

DO NOT pollute the environment by allowing uncontrolled

discharge of waste oil.

HYDRAULIC FLUID DISPOSAL

Do not drain hydraulic oil into the sewer system or dispose in an

uncontrolled location. Hydraulic fluid may take more than a year to

breakdown in the environment and the ingredients may still be toxic.

Contact your local municipality for proper disposal instructions or

locations.

TROUBLESHOOTING

Visit a Princess Auto Ltd. location for a solution if the tool does not

function properly or parts are missing. If unable to do so, have a

qualified technician service the tool.

9081548 PNEUMATIC/HYDRAULIC SHOP PRESS V1.0

Assistance available at www.princessauto.com or 1-800-665-8685 Page 18

Problem(s) Possible Cause(s) Suggested Solution(s)

No oil flow. 1. Cylinder doesn’t

move.

2. Air lock in the lines.

3. No pressure reading

on gauge.

1. Check oil level. Fill as required.

2. Loosen fitting to bleed line.

3. Check pressure gauge. Replace if

defective.

a. Check control valve. Clean,

repair or replace as required.

b. Check cylinder seals. Oil

bypassing in cylinder. Replace

seals.

Oil on Press. 1. Oil leaking from

cylinder.

2. Oil leaking from

loose fitting or line.

1. Replace seals as required.

2. Tighten or add sealant as required.

a. Defective fitting. Replace.

Cylinder ram

doesn’t move.

1. Hydraulic problems.

2. Press overloaded.

3. Ram jammed.

4. Ram binding.

5. Press efficiency

drops.

1. Check hydraulic system. Check

workpiece.

2. Exceeded capacity of Press. Use a

larger press.

3. Check cylinder. Remove defective

part and repair.

4. Cylinder ram is bent. Replace ram

and seals. Use more care when

applying loads.

5. Purge air from hydraulic system as

described in Bleeding the Hydraulic

System.

V1.0 PNEUMATIC/HYDRAULIC SHOP PRESS 9081548

Page 19 Assistance available at www.princessauto.com or 1-800-665-8685

PARTS BREAKDOWN

PARTS LIST

#DESCRIPTION QTY

1 Frame 1

2 Bolt M10x30 12

3 Support strut 4

4 Base 2

5 Washer M10 17

6 Lock washer M10 12

# DESCRIPTION QTY

7 M10 Nut 12

8 Foot air valve 1

9 Intake air hose 1

10 Air hose 1

11 Handle 1

12 Air pump 1

9081548 PNEUMATIC/HYDRAULIC SHOP PRESS V1.0

Assistance available at www.princessauto.com or 1-800-665-8685 Page 20

La page est en cours de chargement...

PROPOINT 9081548 Le manuel du propriétaire

Marque: PROPOINT

Modèle: 9081548

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: PROPOINT 9081548 Owner's manual

PROPOINT 9081548 Le manuel du propriétaire

PROPOINT 9081548 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents