Maytag Bottom freezer refrigerator Manuel utilisateur

Marque: Maytag

Modèle: Bottom freezer refrigerator

Catégorie: Congélateurs

Taper: Manuel utilisateur

Form No. A/03/02 Part No. 12642705 h t t p : / / w w w . m a y t a g . c o m 67001275 Litho U.S.A.

BOTTOM FREEZER REFRIGERATOR

care & cleaning

safety

Installer: Please leave this manual with

this appliance.

Consumer: Please read and keep this

manual for future reference. Keep sales

receipt and/or cancelled check as proof of

purchase.

If you have questions, write us (include

your model number and phone number)

or call:

Maytag Appliances Sales Company

Attn: CAIR

Center

P.O. Box 2370

Cleveland, TN 37320-2370

1-800-688-9900 U.S.A.

1-800-688-2002 Canada

1-800-688-2080 (U.S.A. TTY for

hearing or speech impaired)

(Mon.-Fri., 8 am-8 pm Eastern Time)

Internet: http://www.maytag.com

For service information, see page 19.

In our continuing effort to improve

the quality and performance of our

appliances, it may be necessary to

make changes to the appliance

without revising this guide.

before you call

Page 1

Pages 2-6

Page 7

Page 10

Pages 8-9

Pages 11-12

Page 13

Pages 13-15

Page 16

Pages 17-18

Page 19

Page 20

Page 40

Model Number

Serial Number

Date of Purchase

operating sounds

food storage tips

looking inside

ice service

proper temperatures

installation

storing the refrigerator

IMPORTANT SAFETY INSTRUCTIONS

➢ Use the refrigerator only for its intend-

ed purpose.

➢ To prevent possibility of hazard due to

electrical shock, never plug the refrig-

erator into a receptacle which has not

been grounded adequately and in

accordance with the local and national

electrical codes. See warning and

the grounding instructions that follow.

➢ Unplug the refrigerator or disconnect

the circuit breaker before cleaning or

replacing a light bulb.

➢ In case of power failure, minimize door

openings. If the power failure is of a

long duration, protect the food by plac-

ing blocks of dry ice on top of the

packages or check with a local frozen

foods locker about temporary storage.

Frozen foods which have thawed

completely should not be refrozen.

➢ Any electrical service cord that

becomes frayed or damaged should

be immediately repaired or replaced.

Never unplug your appliance by

pulling on the power cord.

➢ Your refrigerator should not be operat-

ed in the presence of explosive fumes.

➢ Children should not climb, hang or

stand on the shelves of this refrigerator.

This appliance is equipped with a three-

pronged grounding plug for your protec-

tion against possible electrical shock haz-

ards. It must be plugged into a grounding

receptacle. Where a standard two-prong

wall receptacle is encountered, it is the

personal responsibility and obligation of

the customer to have it replaced with a

properly grounded three-prong wall

receptacle. Do not under any circum-

stances, cut or remove the third (ground)

prong from the power cord. Do not use

an adapter plug.

Save these instructions for future reference

What you need to know

about safety

instructions

Warning and Important Safety Instruc-

tions appearing in this manual are not

meant to cover all possible conditions

and situations that may occur. Common

sense, caution and care must be exer-

cised when installing, maintaining or

operating this appliance.

Always contact your dealer, distributor,

service agent or manufacturer about

problems or conditions you do not under-

stand.

RECOGNIZE SAFETY

SYMBOLS, WORDS,

LABELS

POWER SUPPLY CORD

WITH 3-PRONG

GROUNDING PLUG

GROUNDING TYPE

WALL RECEPTACLE

DANGER – Immediate hazards which

WILL result in severe personal injury

or death.

DANGER

WARNING – Hazards or unsafe prac-

tices which COULD result in severe

personal injury or death.

WARNING

CAUTION – Hazards or unsafe prac-

tices which COULD result in minor

personal injury.

CAUTION

When using your appliance, always

follow basic precautions.

WARNING

➢ This appliance is designed to

operate on a normal 115 volt, 15

amp, 60 cycle line. There should

be a separate, grounded circuit

serving this appliance only. Do

not use an extension cord. Do

not use any device that will alter

the electrical performance of this

appliance.

WARNING

DANGER: Child entrapment and

suffocation are not problems of the

past. Junked or abandoned refrigera-

tors are still dangerous…even if they

will sit for “just a few days.” If you are

getting rid of your old refrigerator,

please follow the instructions below to

help prevent accidents.

➢ Take off the

doors.

➢ Leave the

shelves in

place so that

children may

not easily

climb inside.

DANGER

safety

INSTALLATION

Your new refrigerator was packed care-

fully for shipment. Remove and discard

shelf packing clips (if used) located just

above each shelf where they hook onto

the frame. To remove plastic clips wiggle

the clips sideways and pull straight out.

Transport

➢ NEVER transport the refrigerator on

its side. If an upright position is not

possible, lay the refrigerator on its

back. Allow the refrigerator to sit

upright for approximately 30 minutes

prior to plugging the refrigerator in to

assure oil return to the compressor.

Plugging the refrigerator in immedi-

ately may cause damage to internal

parts.

➢ Use an appliance dolly when moving

the refrigerator. ALWAYS truck the

refrigerator from the side – NEVER

from the front or back.

➢ Protect outside finish during transport

by wrapping cabinet in blankets or

inserting padding between the refrig-

erator and dolly.

➢ Secure the refrigerator to dolly firmly

with straps or bungee cords. Thread

straps through handles when possi-

ble. DO NOT overtighten. Overtight-

ening restraints may dent or damage

outside finish.

Location

➢ Allow for a free flow of air through the

front base grille.

➢ Install the refrigerator where the room

temperature will not go below 55° F.

With temperatures below 55° F, the

refrigerator will not run frequently

enough to maintain proper tempera-

ture in the freezer.

➢ Locate the refrigerator away from heat

producing appliances such as the

range or dishwasher, heat vents and

direct sunlight.

➢ A minimum of 1/2" clearance is re-

quired on the top and back. Allow 1/2"

at the sides for ease of installation. If

refrigerator is placed with the door

hinge side against a wall, you may

want to allow additional space.

➢ Use caution when installing the refrig-

erator on vinyl or hardwood floors so

as not to mark or otherwise damage

the flooring. A piece of plywood, a rug

or other material should be used to

protect the floor while positioning the

refrigerator.

Leveling

To enhance appearance and maintain

performance, the refrigerator should be

level.

If your refrigerator requires a water

supply connection, see How to Connect

the Water Supply on page 6, before

leveling your refrigerator.

For further assistance, call 1-800-688-9900 U.S.A., 1-800-688-2002 Canada or www.maytag.com

➢ Move the refrigerator to final location

and plug the power cord in.

➢ Remove base grille and bottom

cover(s).

➢ Using a 3/8" hex head screwdriver,

turn roller adjustment screws to raise

or lower front of refrigerator. (Front of

refrigerator needs to be 1/4" higher

than the back of the refrigerator for

proper door closure.)

➢ Level refrigerator cabinet from side to

side by adjusting left and right roller

adjustment screws, as needed.

➢ Turn stabilizing leg clockwise until

firmly against floor.

IMPORTANT: For pullout drawer models

only – After completing the above steps,

turn roller adjustment screws 2 to 3 times

counterclockwise, so that the full weight

of the refrigerator rests on stabilizing

legs.

➢ Using a level, make sure front of

refrigerator is 1/4" (6 mm) or 1/2

bubble higher than back of refrigera-

tor.

➢ Replace toe grille and bracket

cover(s). See markings on inside of

toe grille to insure proper placement.

➢ Snap bottom portion into place

first. Press down on top part of grille

until top portion snaps into place.

Roller

Adjustment

Screw

Stabilizing

Leg

To protect personal property or refrig-

erator from damage, observe the

following:

➢ Protect soft vinyl or other flooring

with cardboard, rugs or other pro-

tective materials.

➢ Do not use power tools when per-

forming leveling procedure.

CAUTION

Installing side-mounted

handles

If installing handles for the first time, the

fresh food and freezer handles can be

located on the back of the refrigerator.

➢ Using a T-15 Torx

* screw driver,

remove screws from the side of the

fresh food door or top of the freezer

door or drawer.

➢ Align handle screw holes with door

holes and install handles with screws

that came in these screw holes.

Removing side-mounted

handles

Removing handles may be necessary

when transporting the refrigerator

through tight spaces, or when reversing

the door.

➢ Using a T-15 Torx

* screw driver,

remove handle by removing three

screws from side of fresh food door or

top of freezer door or drawer.

➢ Retain screws for later replacement.

INSTALLATION

,CONT.

How to remove the

doors and hinges

Some installations require complete door

removal to get refrigerator to its final loca-

tion.

WARNING – To avoid electrical shock

which can cause severe personal injury

or death, disconnect power to refrigera-

tor before removing doors. Connect

power only after replacing doors.

WARNING

CAUTION – To avoid damage to walls

and flooring, protect soft vinyl or other

flooring with cardboard, rugs or other

protective material.

CAUTION

➢ Unplug power cord from power

source.

➢ Remove top hinge cover from refriger-

ator door by removing Phillips screw.

• Retain screw and cover for replace-

ment.

➢ Unscrew 5/16" hex head screws from

top hinge to remove hinge.

• Retain all screws for later use.

➢ Lift refrigerator door from center hinge

pin.

➢ Hold freezer door in place while

removing center hinge pin with a 5/16"

hex nut driver. Remove freezer door.

• Retain hinge pin for later use.

*Torx

is a registered trademark of Textron, Inc.*Torx

is a registered trademark of Textron, Inc.

installation

For further assistance, call 1-800-688-9900 U.S.A., 1-800-688-2002 Canada or www.maytag.com

How to replace the

doors and hinges

➢ Install hinge assemblies:

• Install top hinge loosely with 5/16"

hex head screws.

• Install center hinge with Phillips

screws.

• Install bottom hinge with 3/8" hex

head screws.

➢ Insert bottom hinge pin (some models).

• Locate bottom hinge hole closest to

outside edge of cabinet, and insert

bottom hinge pin. Replace any door

shims, if present.

➢ Place hinge side of freezer door on

bottom hinge pin and hold freezer

door upright while installing center

hinge pin with 5/16" hex head driver.

• Replace any applicable door shims.

•Make sure the hinge pin fit is tight.

➢ Place hinge side of refrigerator door

on center hinge pin.

➢ While holding refrigerator door

upright, tighten down top hinge with

5/16" hex head driver and replace

hinge cover.

➢ Remove Phillips screws to remove

center hinge.

• Retain all screws for later use.

➢ Remove bottom hinge or stabilizing

bracket with 3/8" hex head driver.

• Lift out bottom hinge pin (some mod-

els).

• Retain hinge pin and screws for later

use.

➢ Remove toe grille and bottom bracket

cover(s).

• Depending on the model of your unit,

you may have one or two bracket

covers.

How to reverse the

doors

➢ Perform all steps listed in How to

Remove the Doors and Hinges on

page 3.

➢ Remove cabinet plugs with flat blade

screwdriver tip wrapped in masking

tape.

➢ Transfer cabinet plugs and cabinet

screws to opposite side of cabinet.

➢ Remove center mullion screws with

5/16" hex head driver.

➢ For swing doors only – remove bottom

mullion screws with 3/8" hex head

driver.

➢ Using a Phillips screwdriver, transfer

door stops from bottom edge of fresh

food and freezer door to opposite side

of door edge.

➢ See How to Install and Remove

Handles on page 3 to remove and

reinstall handles.

➢ Proceed to How to Replace the

Doors and Hinges on page 4 to

mount doors.

How to remove and

install the pullout

drawer

➢ Pull drawer open to full extension.

➢ Remove Phillips screw from each side

of rail system.

➢ Remove lower basket by lifting basket

from rail system.

➢ Lift top of door to unhook door sup-

ports from rail system. Lift door out to

remove.

To install:

➢ Pull both rails out to full extension.

➢ With drawer pulled out to full exten-

sion, insert lower basket by aligning

tabs on both sides of lower basket with

notches in rail assembly. Verify that

the basket sides are hooked securely

over the rails.

➢ Slide upper basket into freezer. Make

sure that rear of basket hooks behind

rail catch.

INSTALLATION

,CONT.

➢ Lower door into final position.

➢ Replace and tighten Phillips screws

that were removed from each side of

rail system.

To remove:

➢ Pull upper basket out to full extension

and lift out to remove.

WARNING – To avoid electrical shock

which can cause severe personal

injury or death, disconnect power to

refrigerator before removing the draw-

er. After replacing the drawer, connect

power.

WARNING

CAUTION – To avoid possible injury,

product, or property damage, you will

need two people to perform the follow-

ing instructions.

CAUTION

➢ While supporting door, hook door sup-

ports into tabs located on inside of rail.

installation

For further assistance, call 1-800-688-9900 U.S.A., 1-800-688-2002 Canada or www.maytag.com

How to connect the

water supply for

optional automatic

ice maker

MATERIALS NEEDED

➢ 1/4" outer diameter flexible copper

tubing

➢ Shut-off valve (requires a 1/4" hole to

be drilled into water supply before

valve attachment)

➢ Needle-nose pliers

➢ Adjustable wrench

➢ Water bucket

➢ Flat-blade screwdriver

➢ 1/4" hex nut driver

➢ Phillips screwdriver

➢ Masking tape or small plastic bag

➢ Create service loop with tubing using

care to avoid kinks in tubing.

➢ Remove plastic cap from water valve

inlet port.

➢ Place brass nut and sleeve on copper

tube end as illustrated.

➢ Place end of copper tubing into water

valve inlet port. Shape tubing slightly –

DO NOT KINK – so that tubing feeds

straight into inlet port.

➢ Slide brass nut over

sleeve and screw

nut into inlet port.

Tighten nut with

wrench.

IMPORTANT: DO

NOT overtighten.

Cross threading may occur.

➢ Pull on tubing to

confirm connection

is secure. Connect

tubing to frame with

water tubing clamp

and turn on water

supply. Check for

leaks and correct, if

present.

➢ Monitor water connection for 24

hours. Correct leaks, if necessary.

NOTE

❚ Add 8' to tubing length needed to

reach water supply for creation of

service loop.

Brass

Nut Sleeve

To avoid property damage or possi-

ble injury, follow basic precautions,

including the following:

➢ Consult a plumber to connect

copper tubing to household plumb-

ing to assure compliance with local

codes and ordinances.

➢ Confirm water pressure to water

valve is between 20 and 100

pounds per square inch. If water

filter is installed, water pressure to

water valve must be a minimum of

35 pounds per square inch.

➢ DO NOT use a self-piercing, or

3/16" saddle valve! Both reduce

water flow, become clogged over

time, and may cause leaks if repair

is attempted.

➢ Tighten nuts by hand to prevent

cross threading. Finish tightening

nuts with pliers and wrenches. Do

not overtighten.

➢ Wait 24 hours before placing refrig-

erator into final position to check

and correct any water leaks.

CAUTION

To reduce the risk of injury or

death, follow the basic precautions,

including the following:

➢ Read all instructions before

installing ice maker.

➢ DO NOT attempt installation if

instructions are not understood or if

they are beyond personal skill

level.

➢ Observe all local codes and ordi-

nances.

➢ DO NOT service ice maker unless

specifically recommended in

owner’s manual or published user-

repair instructions.

➢ Disconnect power to refrigerator

prior to installing ice maker.

WARNING

SETTING AND MAINTAINING PROPER TEMPERATURES

The controls are located at the top front of the refrigerator and freezer compartments. NOTE: The freezer control turns the cooling

system on. Neither section will cool if freezer control is set to off.

Initial control settings

After plugging the refrigerator in, set the

controls.

➢ To adjust the controls, turn the control

knob to the left or right as desired.

➢ Initially set the refrigerator control on

➢ Initially set the freezer control on 4.

➢ Let the refrigerator run at least 8-12

hours before adding food.

Warm cabinet surfaces

At times, the front of the refrigerator cab-

inet may be warm to the touch. This is a

normal occurrence that helps prevent

moisture from condensing on the cabinet.

This condition will be more noticeable

when you first start the refrigerator, dur-

ing hot weather and after excessive or

lengthy door openings.

TEMPERATURE CONTROL GUIDE

Refrigerator too warm Turn the refrigerator control to next higher number.

Refrigerator too cold Turn the refrigerator control to next lower number.

Freezer too warm Turn the freezer control to next higher number.

Freezer too cold Turn the freezer control to next lower number.

Turn refrigerator OFF Turn the freezer control to OFF.

NOTE: Turning freezer control to OFF stops cooling in both compartments. It does not

shut off power to the refrigerator.

Adjusting the controls

➢ 24 hours after adding food, you may

decide that one or both compartments

should be colder or warmer. If so,

adjust the control(s) as indicated in the

table below.

➢ Except when starting the refrigerator,

do not change either control more

than one number at a time.

➢ Allow 5-8 hours for temperatures to

stabilize.

➢ Changing either control will have

some effect on the temperature of the

other compartment.

Refrigerator Control

Freezer Control

proper temperatures

For further assistance, call 1-800-688-9900 U.S.A., 1-800-688-2002 Canada or www.maytag.com

LOOKING INSIDE

Fresh food compartment

shelves

Your refrigerator has either Spill-

Catcher™ or Tempered Glass Shelves.

The Spill-Catcher™ shelves have a spill

retainer edge which allows for easier

clean up, and some are equipped with

the Easy Glide slide out feature.

To slide out (select models), grasp the

front of the shelf and pull forward. Push in

the shelf to return to the original position.

To remove a shelf, slightly lift up the rear

of the shelf and pull the shelf straight out.

To lock the shelf into another position, tilt

up the front edge of the shelf. Insert the

hooks into the desired frame openings and

let the shelf settle into place, being sure

the shelf is securely locked at the rear.

ELEVATOR™ SHELF

The fresh food compartment is equipped

with an Elevator™ Shelf. This shelf has

a spill retainer edge for easy cleanup. It

also has the convenient slide out feature

that allows easy access to items stored at

the rear of the shelf.

This shelf can be adjusted up or down

without having to be unloaded of its con-

tents. To adjust an Elevator™ Shelf, pull

out the knob on the crank handle. Rotate

the crank clockwise to raise the height of

the shelf, and counterclockwise to lower

the height of the shelf.

To remove the Elevator™ shelf for occa-

sional cleaning, completely unload the

shelf and pull the shelf forward. When the

shelf stops, press up on the tabs located

underneath its outside edges, then con-

tinue pulling forward, clear of the frame.

To reinstall, align the shelf to the frame

and push it all the way back. (There is no

need to depress the tabs for reinstallation).

In ordinary use, the Elevator™ shelf with

the frame assembly does NOT require

removal. Though unlikely, and not recom-

mended, the correct removal procedure

is as follows:

Unload the shelf completely, raise the

shelf to its highest possible position. While

supporting the shelf and frame from the

front, press both locks inward. Lift slightly

and tilt the frame assembly to allow the

rear guides to clear the vertical rails.

To reinstall, tilt the frame assembly while

depressing both locks, reposition the rear

guide behind the vertical rails. When the

shelf is level, release the locks allowing

the shelf to latch in the correct position.

DOOR STORAGE

The Pick-Off Door Bins are adjustable

and can be easily removed.

To remove, lift the bin front up until it

clears the retainers on the door liner then

pull the bin straight out.

To replace, reverse the above procedure.

DAIRY COMPARTMENT

The dairy compartment provides conven-

ient storage for items such as butter and

margarine. This compartment is an

adjustable feature located in the door. It

can be moved to several different loca-

tions to accommodate storage needs.

To remove:

➢ Open dairy door, pull upward and tilt

out.

To reinstall:

➢ Reverse previous

procedure.

FULL WIDTH DOOR SHELF

The lower shelf on the door is full width

and not adjustable.

To remove for cleaning:

➢ Lift shelf up and out.

To reinstall:

➢ Reverse above pro-

cedure.

Your refrigerator may come equipped

with an Egg Cradle (style may vary). It

can be removed to be washed or carried

to a work area.

Special storage areas

Your refrigerator has a Snack Center

Drawer.

To remove the Snack Center Drawer

for cleaning:

➢ Pull the drawer out until it stops.

➢ Lift the drawer up slightly and pull it out.

To reinstall the drawer:

➢ Reverse the above procedure.

This drawer can be positioned as desired

on either the left or right side of the refrig-

erator cabinet.

For best results, keep this drawer closed

tightly.

The Crispers provide storage for fruit

and vegetables. There is a humidity con-

trol located on the crisper shelf above

each of the crisper drawers.

➢ For fruit storage,

slide the crisper con-

trol toward the cen-

ter to provide lower

humidity conditions

in the drawer.

➢ For vegetable storage, slide the crisper

control away from the center to provide

higher humidity conditions in the

drawer.

➢

Never attempt to adjust a shelf

that is loaded with food (except

in the case of the Elevator

Shelf).

WARNING

To remove a crisper drawer for clean-

ing:

➢ Pull out the crisper until it stops.

➢ Tilt the drawer front up and pull it out.

To reinstall a crisper drawer:

➢ Align the drawer in the tracks.

➢ Lift the drawer front and slide in.

For best results, keep the crispers tightly

closed.

To remove the Crisper Top:

➢ Remove drawers as instructed above.

➢ Place hand beneath frame to push up

glass from underneath. Lift glass out.

➢ Lift frame from refrigerator liner rails.

To reinstall the Crisper Top:

➢ Repeat above instructions in reverse

order.

If door doesn’t open far enough to

remove drawers:

➢ Remove drawer furthest from hinge

side of cabinet.

➢ Remove glass as instructed previously.

➢ Lift center divider from frame. Slide

existing drawer away from hinge side

of cabinet and remove.

Freezer compartment

shelves and baskets

WIRE ICE SERVICE RACK

To install:

➢ Position wire rack against the freezer

wall, above plastic supports.

➢ Slide the rack down, over the plastic

supports until the front and back loops

are firmly seated.

To remove:

➢ Perform above steps in reverse order.

FIXED OR SLIDE-OUT

FREEZER SHELF

(Select Models)

To remove:

➢ Pull shelf out to full extension.

➢ Tilt up front of shelf and pull straight

out.

To reinstall:

➢ Insert shelf onto freezer liner rails and

push to back of compartment.

UPPER WIRE BASKET

(Select Models)

To remove:

➢ Pull basket out to

full extension.

➢ Tilt up front of

basket and pull

straight out.

To reinstall:

➢ Insert basket into freezer liner rails

and push back into place.

PULLOUT LOWER

DRAWER BASKETS

(Select Models)

To remove bottom

basket:

➢ Lift basket from

rail guides.

To reinstall bottom

basket:

➢ With drawer pulled out to full exten-

sion, insert lower basket by aligning

tabs on both sides of lower basket with

notches in rail assembly. Verify that

the basket sides are hooked securely

over the rails.

LOWER BASKET DIVIDER

(Select Models)

The lower basket divider allows the

basket area to be organized into

sections.

To remove divider:

➢ Pull divider

straight up.

To reinstall divider:

➢ Hook top corners of divider over top

horizontal basket rungs.

Freezer door storage

FIXED DOOR SHELF

The fixed door shelf provides convenient

storage for frozen food items in freezer

door.

To remove door shelf:

➢ Lift assembly from side liner tabs and

pull out.

To reinstall door shelf:

➢ Fit ends of shelf assembly on liner

tabs and slide down.

TILT-OUT BIN (Select Models)

The tilt-out bin

in the freezer

door tilts for-

ward for easy

access to

stored items.

LOOKING INSIDE

,CONT.

To prevent accidental child entrap-

ment or suffocation risk, DO NOT

remove the divider in the top freezer

basket.

DANGER

ice service

For further assistance, call 1-800-688-9900 U.S.A., 1-800-688-2002 Canada or www.maytag.com

ICE SERVICE

Your refrigerator is automatic ice maker

ready. The number of the appropriate ice

maker kit is IC11. The kit contains instal-

lation instructions and water connection

instructions.

Other models have a factory installed ice

maker. Connect the ice maker to the

water supply as instructed in the separate

instructions furnished with the refrigera-

tor. Proper water flow and a level

refrigerator are essential for optimal

ice maker performance.

After your refrigerator has been connect-

ed to the water supply, move the sensor

arm into the down position. The ice

maker will fill with water when the freezer

reaches the proper temperature.

Using ice maker for the first time:

➢ Confirm ice bin is in place and ice

maker arm is down.

NOTE

❚ Energy rating guides that are post-

ed on the refrigerator at the time of

purchase do not include optional

ice maker energy usage.

➢ Allow approximately 24 hours after

installation to receive first harvest of ice.

➢ Discard ice created within first 12

hours of operation to verify system is

flushed of impurities.

Operating instructions:

➢ Confirm ice bin is in place and ice

maker arm is down.

➢ After freezer section reaches between

0° to 2° F (-18° to -17° C), ice maker

fills with water and begins operating.

You will have a complete harvest of

ice approximately every 3 hours.

➢ Stop ice production by raising ice

maker arm until click is heard.

➢ Ice maker will remain in the off posi-

tion until arm is pushed down.

➢ The first one or two batches will proba-

bly contain undersized and irregular

cubes because of air in the supply line.

➢ The initial batch may also contain

impurities from the new water supply

piping. Therefore, all cubes from the

first two or three batches should be

discarded.

➢ When the ice cubes are ejected it is

normal for several cubes to be joined

together at the ends. They can easily

be broken apart. The ice maker will

continue to make ice until the supply

of ice cubes raises the sensor arm,

shutting the ice maker off.

➢ Certain sounds may accompany the

various cycles of the ice maker. The

motor may have a slight hum, the

cubes will rattle as they fall into an

empty storage pan and the water

valve may click or “buzz” occasionally.

➢ If the ice is not used frequently, the ice

cubes will become cloudy, shrink, stick

together and taste stale. Empty the ice

storage bin periodically and wash it in

lukewarm water. Be sure to dry the bin

thoroughly before replacing it.

➢ Beverages and foods should not be

placed in the ice storage bin for quick

chilling. These items can block the

sensor arm, causing the ice maker to

malfunction.

➢ Turn off (arm up) the ice maker when

the water supply is to be shut off for

several hours.

To remove the ice bin:

➢ Pull it forward, away from the ice

maker. To avoid the ice maker dump-

ing ice while the bin is removed, turn

the ice maker off by raising the sensor

arm.

To reinstall the ice bin:

➢ Reverse the above procedure. Turn

the ice maker on by lowering the sen-

sor arm.

Ice cube trays

Some models are equipped with ice cube

trays and an ice storage bin. To release the

ice cubes from a tray, hold the tray upside

down over the bin and twist both ends.

Automatic ice maker

(optional)

➢ After freezer section reaches between

0° to 2° F (-18° to -17° C), ice maker

fills with water and begins operating.

FOR YOUR SAFETY

Do not place fingers or hands on

the automatic ice making mecha-

nism while the refrigerator is

plugged in. This will help protect

you from possible injury. It will also

prevent interference with moving

parts of the ejector mechanism and

the heating element that releases

the cubes.

Under certain rare circumstances,

ice cubes may be discolored,

usually appearing with a green-

bluish hue. The cause of this

unusual discoloration can be a

combination of factors such as cer-

tain characteristics of local waters,

household plumbing and the accu-

mulation of copper salts in an inac-

tive water supply line which feeds

the ice maker.

Continued consumption of such

discolored ice cubes may be injurious

to health. If such discoloration is

observed, discard the ice cubes

and contact your dealer to pur-

chase and install a water line filter.

WARNING

FOOD STORAGE TIPS

Fresh food storage

➢ The fresh food compartment of a

refrigerator should be kept between

34° F and 40° F with an optimum tem-

perature of 37° F. To check the tem-

perature, place an appliance ther-

mometer in a glass of water and place

in the center of the refrigerator. Check

after 24 hours. If the temperature is

above 40° F adjust the controls as

explained on page 7.

➢ Avoid overcrowding the refrigerator

shelves. This reduces the circulation

of air around the food and results in

uneven cooling.

FRUITS AND

VEGETABLES

➢ Storage in the crisper drawers traps

moisture to help preserve the fruit and

vegetable quality for longer time peri-

ods. (Refer to page 8).

➢ Sort fruits and vegetables before stor-

age and use bruised or soft items first.

Discard those showing signs of decay.

➢ Always wrap odorous foods such as

onions and cabbage so the odor does

not transfer to other foods.

➢ While vegetables need a certain

amount of moisture to remain fresh,

too much moisture can shorten stor-

age times (especially leafy vegeta-

bles). Drain vegetables well before

storing.

MEAT AND CHEESE

➢ Raw meat and poultry should be

wrapped securely so leakage and

contamination of other foods or sur-

faces does not occur.

➢ Occasionally mold will develop on the

surface of hard cheeses (Swiss,

Cheddar, Parmesan). Cut off at least

an inch around and below the moldy

area. Keep your knife or instrument

out of the mold itself. The remaining

cheese will be safe and flavorful to

eat. Do NOT try to save individual

cheese slices, soft cheese, cottage

cheese, cream, sour cream or yogurt

when mold appears.

DAIRY FOOD

➢ Most dairy foods such as milk, yogurt,

sour cream and cottage cheese have

freshness dates on their cartons for

appropriate length of storage. Store

these foods in the original carton and

refrigerate immediately after purchas-

ing and after each use.

Frozen food storage

➢ The freezer compartment of a refriger-

ator should be kept at approximately

0° F. To check the temperature, place

an appliance thermometer between

the frozen packages and check after

24 hours. If the temperature is above

0˚ F, adjust the control as described on

page 7.

➢ A freezer operates more efficiently

when it is at least two-thirds full.

PACKAGING FOODS FOR

FREEZING

➢ To minimize dehydration and quality

deterioration use aluminum foil, freez-

er wrap, freezer bags or airtight con-

tainers. Force as much air out of the

packages as possible and be sure

they are tightly sealed. Trapped air

can cause the food to dry out, change

color and develop an off-flavor (freez-

er burn).

➢ Overwrap fresh meats and poultry

with suitable freezer wrap prior to

freezing.

➢ Do not refreeze meat that has com-

pletely thawed.

LOADING THE FREEZER

➢ Avoid adding too much warm food to

the freezer at one time. This overloads

the freezer, slows the rate of freezing

and can raise the temperature of

frozen foods.

➢ Leave space between the packages so

cold air can circulate freely, allowing

food to freeze as quickly as possible.

➢ Avoid storing hard-to-freeze foods

such as ice cream and orange juice on

the freezer door shelves. These foods

are best stored in the freezer interior

where the temperature varies less

with door openings.

Refer to the Food Storage Chart on

page 12 for approximate storage

times.

For further assistance, call 1-800-688-9900 U.S.A., 1-800-688-2002 Canada or www.maytag.com

food storage tips

FOOD STORAGE CHART

(Storage times are approximate and may vary depending on type of packaging, storage temperature, and the quality of the food when

purchased.)

Foods

Butter

Milk & cream

Cream cheese, cheese

spread & cheese food

Cottage cheese

Sour cream

Hard cheese (Swiss,

Cheddar & Parmesan)

Eggs in the shell

Leftover yolks or whites

Apples

Bananas

Pears, plums, avocados

Berries, cherries, apricots

Grapes

Citrus fruits

Pineapples, cut

Asparagus

Brussels sprouts, broccoli, cau-

liflower, green peas, lima

beans, onions, peppers

Cabbage, celery

Carrots, parsnips, beets, &

turnips

Lettuce

Chicken and Turkey, whole

Chicken and Turkey, pieces

Fish

Bacon

Beef or lamb, ground

Beef or lamb, roast & steak

Ham, fully cooked, whole

half

slices

Luncheon meat

Pork, roast

Pork, chops

Sausage, ground

Sausage, smoked

Veal

Frankfurters

Refrigerator

1 month

1 week

1-2 weeks

3-5 days

10 days

1-2 months

3 weeks

2-4 days

1 month

2-4 days

3-4 days

2-3 days

3-5 days

1-2 weeks

2-3 days

1-2 days

3-5 days

1-2 weeks

7-10 days

1-2 days

7 days

1-2 days

3-5 days

7 days

5 days

3 days

3-5 days

1-2 days

7 days

3-5 days

7 days

Freezer

6-9 months

Not recommended

4-6 months

May become crumbly

Not recommended

9-12 months

8 months (cooked)

6 months (whole/peeled)

Not recommended

6 months

1 month (whole)

Not recommended

6-12 months

8-10 months

Not recommended

8-10 months

Not recommended

12 months

9 months

2-6 months

1 month

3-4 months

6-9 months

1-2 months

4-6 months

4 months

1-2 months

4-6 months

1 month

Storage Tips

Wrap tightly or cover.

Check carton date. Close tightly. Don’t return unused portions to

original container. Don’t freeze cream unless whipped.

Wrap tightly.

Store in original carton. Check carton date.

Wrap tightly. Cut off any mold.

Refrigerate small ends down.

For each cup of yolks to be frozen, add 1 tsp. sugar for use in

sweet, or 1 tsp. salt for non-sweet dishes.

May also store unripe or hard apples at 60-70° F.

Ripen at room temperature before refrigerating. Bananas and

avocados darken when refrigerated.

May also store at 60-70° F. If refrigerated, store uncovered.

Will not ripen after purchase. Use quickly.

Do not wash before refrigerating. Store in crisper.

Wrap odorous foods. Leave peas in pods.

Wrap odorous foods & refrigerate in crisper.

Remove tops. Wrap odorous foods and refrigerate in the crisper.

Keep in original packaging for refrigeration. Place in the Meat and

Cheese Drawer. When freezing longer than 2 weeks, overwrap

with freezer wrap.

Fresh meats can be kept in original packaging for refrigeration.

Place in the Meat and Cheese Drawer. When freezing longer than

2 weeks, overwrap with freezer wrap.

Unopened, vacuum-packed luncheon meat may be kept up to

2 weeks in the Meat and Cheese Drawer.

Processed meats should be tightly wrapped and stored in the Meat

and Cheese Drawer.

EGGS

FRUITS

DAIRY PRODUCTS

Sources: United States Department of Agriculture; Food Marketing Institute; Cooperative Extension Service, Iowa State University

VEGETABLES

MEATS

POULTRY & FISH

STORING THE REFRIGERATOR

Vacations

If you will be gone for a month or less,

leave the controls at the usual settings.

During longer absences:

1. Remove all food.

2. Shut off the ice maker (if installed) and

the valve where you tapped into the

water line to supply the refrigerator.

3. Disconnect the refrigerator from the

electrical outlet.

4. Clean and dry the refrigerator

thoroughly.

5. Leave the doors open to prevent

odors.

Moving

When moving, follow steps 1–4 under

Vacations. In addition, remove and care-

fully pack any items that are easily

removable. Ship the refrigerator in an

upright position with the doors taped

shut.

CARE AND CLEANING

Refer to the chart on the following page for

specific refrigerator cleaning guidelines.

REPLACING A LIGHT BULB

REFRIGERATOR

➢ Remove screw

from light

shield. Retain

for replacement.

➢ Slide shield toward back of compart-

ment to release from light assembly.

➢ Remove light bulbs.

➢ Replace with appliance bulbs no

greater than 40 watts.

➢ Replace light bulb cover by inserting

tabs on light shield into liner holes on

each side of light assembly. Slide

shield toward front of unit until it locks

into place. DO NOT force shield

beyond locking point. Doing so may

damage light shield.

➢ Replace light shield screw.

Freezer

➢ Pinch rear tabs on light cover and pull

straight out.

➢ Remove light bulb.

➢ Replace bulb with appliance bulb no

greater than 40 watts.

➢ Insert top tabs

of light cover

into refrigera-

tor liner and

snap back por-

tion over light

assembly.

CONDENSER

Energy saving tips

➢ When placing refrigerator into final

position, allow for 1" clearance around

the top and sides of unit to supply

ample ventilation.

➢ Locate the refrigerator away from heat

producing appliances such as the

range or dishwasher, heat vents and

direct sunlight.

➢ Level the refrigerator and do not block

ventilation around the front grille.

➢ Keep the freezer full to near capacity

so less cold air will escape during door

openings. When the freezer is less

than two-thirds full, place milk cartons

half full of water in the freezer.

➢ Let hot dishes cool slightly before put-

ting into the refrigerator or freezer.

➢ Cover liquids.

➢ Wipe moisture from the outside of

containers before placing them into

the refrigerator.

➢ Avoid opening the doors too often.

➢ Clean condenser coils every 3 months.

➢ Do not use aluminum foil, wax paper

or paper toweling as shelf liners. This

decreases air flow and causes unit to

run less efficiently.

Cleaning of the condenser is recom-

mended every three months.

➢ Unplug the refrigerator.

➢ Remove the base grille (see page 2)

to access the condenser coils.

➢ Using a vacuum cleaner hose, remove

the dust and soil.

➢ Use a vacuum cleaner hose with the

brush attachment to clean the con-

denser fan outlet grille at the back of

the refrigerator.

Top Tabs

Bottom Tabs

➢

Disconnect the power cord or

disconnect the circuit breaker

before cleaning.

CAUTION

➢

Disconnect the power cord or

disconnect the circuit breaker

before replacing light bulb(s).

Wear gloves as protection

against broken glass.

CAUTION

➢

Disconnect the power cord or

disconnect the circuit breaker

before cleaning the condenser.

CAUTION

care & cleaning

For further assistance, call 1-800-688-9900 U.S.A., 1-800-688-2002 Canada or www.maytag.com

PART DO

➢

Mild detergent and warm water

➢

Mild liquid sprays

➢

Vacuum cleaner attachment

➢ Use 4 tablespoons of baking soda dissolved in 1 quart (1 liter)

warm soapy water.

➢ Rinse surfaces with clean warm water and dry immediately to

avoid water spots.

➢ Use warm, soapy water and a soft, clean cloth or sponge.

➢ Rinse surfaces with clean warm water and dry immediately to

avoid water spots.

➢ Use a vacuum cleaner hose nozzle.

➢ Use a vacuum cleaner hose nozzle with brush attachment.

➢ Follow removal and installation instructions from appropriate

feature section.

➢ Allow items to adjust to room temperature.

➢ Dilute mild detergent and use a soft clean cloth or sponge for

cleaning.

➢ Use a plastic bristle brush to get into crevices.

➢ Rinse surfaces with clean warm water.

➢ Dry glass and clear items immediately to avoid spots.

DO NOT USE

➢ Abrasive or harsh cleaners

➢ Ammonia

➢ Chlorine bleach

➢ Concentrated detergents or

solvents

➢ Metal or plastic-textured

scouring pads

➢ Abrasive or harsh cleaners

➢ Ammonia

➢ Chlorine bleach

➢ Concentrated detergents or

solvents

➢ Metal or plastic-textured

scouring pads

➢ Vinegar-based products

➢ Citrus-based cleaners

➢ Abrasive or harsh cleaners

➢ Metal or plastic-textured

scouring pads

➢ A dishwasher

REFRIGERATOR EXTERIOR

Base grille

Textured Doors

and Exterior

Cabinet Interior

Stainless Steel Doors

and Exterior

IMPORTANT: Damage

to stainless steel finish

due to improper use of

cleaning products or

non-recommended

products is not covered

under this product’s

warranty.

Door Gaskets

Condenser Coil

Remove base grille to

access

Condenser Fan Outlet

Grille

See back of refrigerator

Accessories Shelves,

buckets, drawers, etc.

Refrigerator Cleaning Chart

➢

Disconnect the power cord or disconnect the circuit breaker before cleaning. Do not touch refrigerated surfaces with

wet or damp hands. Damp objects stick to cold metal surfaces. Before cleaning the freezer, allow it to warm up. Allow

glass shelves to warm up before immersing in warm water.

CAUTION

Removing odors from

refrigerator

➢ Remove all food.

➢ Disconnect refrigerator.

➢ Clean the following items using the

appropriate instructions in the Care

and Cleaning section.

–Walls, floor and ceiling of cabinet

interior.

– Drawers, shelves and gaskets

according to the instructions in this

section.

➢ Pay special attention to clean all

crevices by completing the following

steps:

– Dilute mild detergent and brush

solution into crevices using a plas-

tic bristle brush.

– Let stand for 5 minutes.

– Rinse surfaces with warm water.

Dry surfaces with a soft, clean

cloth.

➢ Wash and dry all bottles, containers

and jars. Discard spoiled or expired

items.

➢ Wrap or store odor-causing foods in

tightly-sealed containers to prevent

reoccurring odors.

➢ Connect power to refrigerator and

return food to unit.

➢ After 24 hours, check if odor has been

eliminated.

If odor is still present:

➢ Remove drawers and place on top

shelf of refrigerator.

➢ Pack refrigerator and freezer sections

– including doors – with crumpled

sheets of black and white newspaper.

➢ Place charcoal briquettes randomly on

crumpled newspaper in both freezer

and refrigerator compartments.

➢ Close doors and let stand 24-48

hours.

CARE & CLEANING

,CONT.

operating sounds

For further assistance, call 1-800-688-9900 U.S.A., 1-800-688-2002 Canada or www.maytag.com

NORMAL OPERATING SOUNDS

Improvements in refrigeration design may produce sounds in your new refrigerator that are different or were not present in an older

model. These improvements were made to create a refrigerator that is better at preserving food, more energy efficient, and quieter

overall. Because new refrigerators run quieter, sounds may be detected that were present in older refrigerators, but were masked by

higher sound levels. Many of these sounds are normal. Please note that the surfaces adjacent to a refrigerator, such as hard walls,

floors and cabinetry may make these sounds seem even louder. The following are some of the normal sounds that may be noticed in

a new refrigerator.

SOLUTION

➢ Normal operation

➢ See Installation Instructions for details on how to level your

refrigerator.

➢ Normal operation

➢ Stop sound by raising ice maker arm to ‘off’ position. See

Automatic Ice Maker section on page 10 for details.

➢ Normal operation

POSSIBLE CAUSE

➢ Freezer control (A) clicks when

starting or stopping compressor.

➢ Defrost timer (B) sounds like an

electric clock and snaps in and

out of defrost cycle.

➢ Freezer fan (C) and condenser

fan (D) make this noise while

operating.

➢ Evaporator (E) and heat

exchanger (F) refrigerant makes

this noise when flowing.

➢ Ice cubes from ice maker (some

models) drop into ice bucket (G).

➢ Compressor (H) makes a pul-

sating sound while running.

➢ Refrigerator is not level.

➢ Ice maker water valve (I)

hookup (some models) buzzes

when ice maker fills with water.

➢ Ice maker (J) is in the ‘on’ posi-

tion without water connection.

➢ Compressor (H) can make a high

pitched hum while operating.

➢ Defrost heater (K) hisses,

sizzles, or pops when

operating.

TOPIC

Clicking

Air rushing or whirring

Gurgling or boiling

sound

Thumping

Vibrating noise

Buzzing

Humming

Hissing or popping

BEFORE YOU CALL FOR SERVICE

PROBLEM POSSIBLE CAUSES WHAT TO DO

Freezer control and lights Refrigerator is in defrost mode. Normal operation. Wait 40 minutes to see if refrigerator restarts.

are on, but compressor

is not operating

Refrigerator does not Refrigerator is not plugged in. Plug in unit.

operate

Freezer control is not on. See page 7.

Fuse is blown, or circuit breaker needs Replace blown fuses. Reset circuit breaker.

to be reset.

Power outage has occurred Call local power company listing to report outage.

Refrigerator still won’t Unit is malfunctioning. Unplug refrigerator and transfer food to another refrigerator. If

operate another unit is not available, place dry ice in freezer section to

preserve food. Warranty does not cover food loss.

Contact service for assistance.

Refrigerator has an odor Compartment is dirty or has odor-causing See page 15.

food.

Crisper drawers do not Contents of drawer, or positioning of items Reposition food items and containers.

close freely in the surrounding compartment could be

obstructing drawer.

Drawer is not in proper position. See page 8 for proper crisper placement.

Refrigerator is not level. See page 2.

Drawer channels are dirty or need Clean drawer channels with warm, soapy water. Rinse and dry.

treatment.

Apply a thin layer of petroleum jelly to drawer channels.

Refrigerator runs too Doors have been opened frequently or Minimize door openings.

frequently for long periods of time.

Humidity or heat in surrounding area is Normal operation.

high.

Food has recently been added. Allow time for recently added food to reach refrigerator or

freezer temperature.

Refrigerator is exposed to heat by Evaluate your refrigerator’s environment. Refrigerator may

environment or by appliances nearby. need to be moved to run more efficiently.

Condenser coils are dirty. Clean according to cleaning instructions. See page 13.

Controls need to be adjusted. See page 7.

Door is not closing properly. Refrigerator is not level. See page 2.

Today’s refrigerators start and stop more Check gaskets for proper seal. Clean, if necessary. See page 14.

often to maintain even temperatures.

Check to see if something is preventing door from closing.

Noise, sounds and Normal operation. See page 16.

vibrations

Cabinet not level. Level cabinet. See page 2.

Food temperature Condenser coils are dirty. Clean according to cleaning instructions. See page 13.

is too cold

Refrigerator or freezer controls are set See page 7.

too high.

Food temperature Door is not closing properly. Refrigerator is not level. See page 2.

is too warm

Check gaskets for proper seal. Clean, if necessary. See page 14.

Check to see if something is preventing door from closing.

Controls need to be adjusted. See page 7.

Condenser coils are dirty. Clean according to cleaning instructions. See page 13.

Rear air grille is blocked. Check the positioning of food items in refrigerator to make sure

grille is not blocked. Rear air grilles are located under crisper

drawers.

Prolonged door openings. Minimize door openings.

Review this chart of troubleshooting tips first…you may not need to call for service at all.

GENERAL OPERATION

NOISE

TEMPERATURE

before you call

For further assistance, call 1-800-688-9900 U.S.A., 1-800-688-2002 Canada or www.maytag.com

PROBLEM POSSIBLE CAUSES WHAT TO DO

Refrigerator is leaking Plastic tubing was used to complete water Use copper tubing for installation. Plastic is less durable and

water connection. can cause leakage.

Ice forms in inlet tube to Improper water valve was installed. Check water connection procedure in the Installation

ice maker Instructions. Self-piercing and 3/16” saddle valves cause low

water pressure and may clog the line over time.

Water pressure is low. Water pressure must be between 20 to 100 pounds per square

inch to function properly.

Water flow is slower than Freezer temperature is too high. See page 7. Freezer temperature should be approximately

normal 0° F (-18° C).

Water pressure is low. Water pressure must be between 20 to 100 pounds per square

inch to function properly.

Improper water valve was installed. Check water connection procedure in the Installation

Instructions. Self-piercing and 3/16” saddle valves cause low

water pressure and may clog the line over time.

Water droplets form on Check gaskets for proper seal. Clean, if necessary. See page 14.

outside of refrigerator

Humidity levels are high. Normal during times of high humidity.

Controls require adjustment. See page 7.

Water droplets form on Humidity levels are high or door has been Minimize door openings.

inside of refrigerator been opened frequently.

Check gaskets for proper seal. Clean, if necessary. See page 14.

ICEMOISTURE

MAYTAG • 403 West Fourth Street North • P. O. Box 39 • Newton, Iowa 50208

Maytag warranty What is not covered by these warranties:

1. Conditions and damages resulting from any of the following:

a. Improper installation, delivery, or maintenance.

b. Any repair, modification, alteration, or adjustment not authorized by the

manufacturer or an authorized servicer.

c. Misuse, abuse, accidents, or unreasonable use.

d. Incorrect electric current, voltage, or supply.

e. Improper setting of any control.

2. Warranties are void if the original serial numbers have been removed,

altered, or cannot be readily determined.

3. Light bulbs.

4. Products purchased for commercial or industrial use.

5. The cost of service or service call to:

a. Correct installation errors.

b. Instruct the user on the proper use of the product.

c. Transport the appliance to the servicer.

6. Consequential or incidental damages sustained by any person as a result

of any breach of these warranties. Some states do not allow the exclusion

or limitation of consequential or incidental damages, so the above exclu-

sion may not apply.

If you need service

❚ Call the dealer from whom your appliance was purchased or call Maytag

Appliances Sales Company, Maytag Customer Assistance at 1-800-688-

9900, USA or 1-800-688-2002 Canada to locate an authorized servicer.

❚ Be sure to retain proof of purchase to verify warranty status. Refer to

WARRANTY for further information on owner’s responsibilities for

warranty service.

❚ If the dealer or service company cannot resolve the problem, write to

Maytag Appliances Sales Company, Attn: CAIR

Center, P.O. Box 2370,

Cleveland, TN 37320-2370, or call 1-800-688-9900 U.S.A. or 1-800-688-

2002 Canada.

U.S. customers using TTY for deaf, hearing impaired or speech impaired,

call 1-800-688-2080.

NOTE: When writing or calling about a service problem, please include

the following information:

a. Your name, address and telephone number;

b. Model number and serial number;

c. Name and address of your dealer or servicer;

d. A clear description of the problem you are having;

e. Proof of purchase (sales receipt).

❚ User’s guides, service manuals and parts information are available from

Maytag Appliances Sales Company, Maytag Customer Assistance.

Full One Year Warranty

For one (1) year from the date of original retail

purchase, any part that fails in normal home

use will be repaired or replaced free of charge.

Ice Maker - When purchased with the refriger-

ation and installed by the dealer the ice maker

will be considered part of the refrigerator for

warranty purposes.

Limited Warranty - Major Refrigeration

Components

Second Through Fifth Year - After the first

year from the date of original purchase,

through the fifth year, Maytag Appliances will

repair or replace, at its option, free of charge

for parts and labor, any part of the sealed

refrigeration system (consisting of the com-

pressor, evaporator, condenser, drier and con-

necting tubing) and the cabinet liner (exclusive

of the door liner) which fail in normal home use.

Mileage and transportation charges, if

required, shall be the responsibility of the

owner.

Limited Warranty - Other Parts

Second Year - Parts other than major refriger-

ation components which fail in normal home

use during the second year following the date

of original retail purchase will be repaired or

provided free of charge for the part itself, with

the owner paying all other costs, including

labor, mileage and transportation.

Please note: The full warranty and the limited

warranties apply when the refrigerator is locat-

ed in the United States or Canada.

Refrigerators located elsewhere are covered

by the limited warranties only including parts

that fail during the first year.

Limitations of Liability

The warrantor shall not be liable for any inci-

dental or consequential damages, including

food loss. Some states do not allow the exclu-

sion or limitation of consequential damages, so

the above limitation or exclusion may not apply

to you.

The specific warranties expressed above are

the ONLY warranties provided by the manufac-

turer. These warranties give you specific

legal rights, and you may also have other rights

which vary from state to state.

La page charge ...

Maytag Bottom freezer refrigerator Manuel utilisateur

Marque: Maytag

Modèle: Bottom freezer refrigerator

Catégorie: Congélateurs

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Maytag Bottom freezer refrigerator User manual
español: Maytag Bottom freezer refrigerator Manual de usuario

Maytag Bottom freezer refrigerator Manuel utilisateur

Maytag Bottom freezer refrigerator Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents