MartinLogan Outdoor Sat 40 Manuel utilisateur

Marque: MartinLogan

Modèle: Outdoor Sat 40

Taper: Manuel utilisateur

Ce manuel convient également à

OUTDOOR LIVING SERIES

user’s manual

OUTDOOR

40 SAT

OUTDOOR

60 SAT

TABLE OF CONTENTS

Overview ...........................3

MartinLogan Outdoor Living Series Satellite Speakers ...3

Required Tools ..........................3

Power ...............................3

Planning The Install ...................4

Quantity Recommendations .............5

Wiring Recommendations ...............5

Installation Considerations ..............5

Wiring & Speaker Installation ............6

Mono Setup Using 4 Conductor Burial Cable &

Crown Amplifier.........................6

Preparing the 4 Conductor Burial Cable . . . . . . . . . 6

Installing Ground Stake Accessory &

Attaching Speaker .......................7

Installing Surface Mount Bracket Accessory &

Attaching Speaker .......................9

Speaker & Burial Cable Connections ..........11

Speaker Direction & Settings................ 11

Optional Inground Conduit Box..........12

OPTION 1: PVC Conduit Installation ..........12

OPTION 2: Burial Cable Installation ..........12

Test System ........................13

To Avoid Speaker Damage .............14

Listening Outdoors ...................14

Off Season Speaker Cover .............14

Audio Settings Chart ..................15

Warranty ..........................16

Service............................16

Specifications .......................17

Dimensional Drawings ................18

MartinLogan Outdoor Living Series

Satellite Speakers

The MartinLogan Outdoor Living Series satellite speakers are

premium sounding all-season outdoor speakers.

OUTDOOR SAT 40 and OUTDOOR SAT 60 are sold

individually and can be ordered in accordance with the area

to be covered.

Made of durable UV treated ABS plastic, MartinLogan Outdoor

Living Series speakers can endure the elements while providing

years of trouble free service.

While installation is relatively easy, MartinLogan’s Outdoor

Living Series products are designed to be installed by your

authorized MartinLogan dealer.

WARNING!

• ACCOUNT FOR POTENTIAL ELECTRICAL,

GAS, BURIED CABLES, PLUMBING OR

OTHER OBSTACLES BEFORE INSTALLING

GROUND STAKES.

• MANY LOCALITIES FORBID DIGGING

WITHOUT PRIOR NOTIFICATION.

CONTACT LOCAL AUTHORITIES

BEFORE INSTALLATION.

• READ AND FOLLOW all instructions

before beginning installation.

IMPORTANT! CONTENTS OF

OUTDOOR SAT 40 AND OUTDOOR

SAT 60 SATELLITE SPEAKERS DO NOT

CONTAIN MOUNTING OPTIONS. THESE

MUST BE PURCHASED SEPARATELY:

Contents of OUTDOOR SAT 40 and OUTDOOR SAT 60:

• (1) Speaker with Mounting Arm

• (1) Off-Season Speaker Cover

• (2) Silicone-Filled Wire Connectors

Mounting Options (Sold Separately):

• Ground Stake • Surface Mount Bracket

• Inground Conduit Box

Required Tools:

• Shovel • Cable Strippers

• Phillips Screwdriver • Wrench

Power

• Crown CDi 1000 Amplifier or dealer recommended amp

The MartinLogan OUTDOOR SAT 40 and OUTDOOR SAT 60

are passive speakers. These speakers are optimized for use with

the Crown CDi 1000 amplifier which can be programmed

with customized DSP settings for a variety of different speaker/

subwoofer installation scenarios. See ‘Audio Settings Chart’ on

page 15.

8 ohm amplifiers can also be used with the MartinLogan

Outdoor Living system, however, they will not be able to run the

proprietary MartinLogan DSP presets available for the Crown

Amplifier. If you use the speakers and subwoofer with an 8 ohm

amplifier, we recommend the following. Satellite Speakers:

Wire only one speaker per amplifier channel and set the tap

on each speaker to the 8 ohm setting. Note: Do not wire

more than one satellite per amplifier channel in 8 ohm mode.

Subwoofer: Wire one subwoofer per amplifier channel.

OVERVIEW

OUTDOOR

40 SAT

OUTDOOR

60 SAT

PLANNING THE INSTALL

Outdoor

SAT 40

Outdoor

SAT 60

Dynamo

Outdoor

SUB 100

Dynamo

Outdoor

SUB 120

Crown Amplifier

4 Conductor Burial Wire

Subwoofer

Speakers

–

Black Red

Green White

–

• Identify the locations and determine the positioning of

subwoofer(s) and satellite speakers. Evenly distribute

speakers and subwoofer(s) throughout the space.

• Dig the trench according to speakers and accessories to

be installed.

• The trench should be 6”–8” deep.

• If using the Crown CDi 1000 amplifier with MartinLogan

Outdoor Living presents, you can use:

o 1 to 3 subwoofers on channel 1 of the amplifier

o 1 to100 satellite speakers on channel 1 or channel 2 of

the amplifier if running 70V

o 1 to 4 satellite speakers on channel 1 or channel 2 of

the amplifier if running 8 Ohm.

We strongly recommend using burial-rated cable (not

included) when installing any of the Outdoor Living Series

speakers. In addition, it’s critical to use the proper speaker

cable gauge. Please review the chart below.

We do not recommend use of high gauge wires, as

performance will be compromised.

There a few considerations before you start digging a trench:

• Ensure that ALL Speakers are tested prior to installation.

• Ensure that the proposed area is easily accessed and that

the area is not prone to flooding, standing water or where

the speakers can be easily damaged, kicked or struck.

• Consider overall landscape/garden design and positioning

in relation to listening area

WIRING RECOMMENDATIONS

QUANTITY RECOMMENDATIONS

INSTALLATION CONSIDERATIONS

CABLE GAUGE CHART

Total Wire Length 70 Volt 8 Ohm

0–100 feet

(0–30 meters)

18 gauge

or lower

14 gauge

or lower

100+ feet

(30+ meters)

16 gauge

or lower

12 gauge

or lower

USAGE CHART

Product Use 1x per

SAT 40

or SAT 60

250–500

square feet

SUB 100

or SUB 120

1000–2000

square feet

Mono Setup Using 4 Conductor Burial Cable & Crown Amplifier

Preparing the 4 Conductor Burial Cable

WIRING & SPEAKER INSTALLATION

1. Starting with

the first speaker

and every

speaker/sub

that comes after,

create a loop

approximately

6” in length.

3. Use a Round

Cable Stripper

to remove

the outside

protective cable

jacket to expose

the four color-

coded wires.

Separate the

wire loops as

shown.

2. Recommended:

Use a wire tie

(not included) to

keep the wire

loop intact and

act as a strain

relief.

4. Cut the red (+)

and black (-)

wires with cable

strippers and

strip off 1 inch

(25.4mm) of

insulation from

the ends if the

wires to expose

the copper

conductor.

Wires for

Speaker

red (+) &

black (-)

Wires for

Subwoofer

green (+) &

white (-)

MonoMonoMonoMonoMonoMonoMonoMono

SAT 40 OR SAT 60 (70V or 8-Ohm)

SUB 100 OR SUB120 (8 Ohm)

Speakers and subs should be

wired in parallel, not series.

Installing Ground Stake Accessory & Attaching Speaker

1. Remove nut from

the threaded end

of the speaker

arm.

3. Slide the twist

cap over the

speaker arm

then slide

the gasketed

aluminum washer

(from the ground

stake) over the

threaded end of

speaker arm.

4. Using a wrench,

thread and

firmly tighten the

nut (removed in

step 1) over the

threaded end

of the speaker

arm.

2. Remove the twist

cap and gas-

keted aluminum

washer from the

ground stake

accessory.

WIRING & SPEAKER INSTALLATION (CONT’D)

IMPORTANT!

The face of

the aluminum

washer with the

smaller rubber

gasket must be

facing up.

7. To attach the

speaker to the

ground stake,

hand thread the

twist cap to the

ground stake.

8. The speaker is

now mounted

to the ground

stake. The next

step is wiring,

go the ‘Wiring’

section for

instructions.

For wiring instructions see ‘Speaker & Burial Cable Connections’ on page 11.

6. Thread the

speaker’s wiring

through the

wiring hole

in the ground

stake.

5. Using a mallet and

a wooden block,

pound the ground

stake into the

ground. Drive the

ground stake down

until the ground

stake flange is

nearly flush with

the surface. Note:

Leave a slight

gap between

the ground stake

flange and the

ground surface

in order to thread

speaker wiring

through the wiring

hole in the ground

stake.

Installing Surface Mount Bracket Accessory & Attaching Speaker

1. Remove nut from

the threaded end

of the speaker

arm.

3. Slide the twist cap

over the speaker

arm then slide the

gasketed aluminum

washer (from the

ground stake) over

the threaded end

of speaker arm.

4. Using a wrench,

thread and firmly

tighten the nut

(removed in step 1)

over the threaded

end of the speaker

arm.

2. Remove the twist

cap and gasketed

aluminum washer

from the surface

mount bracket

accessory.

IMPORTANT!

The face of

the aluminum

washer with the

smaller rubber

gasket must be

facing up.

WIRING & SPEAKER INSTALLATION (CONT’D)

6. To attach the

speaker to the

surface mount

bracket base:

a) First hand

thread the twist

cap to the

surface mount

bracket base.

b) Now firmly

tighten the

twist cap with

the provided

wrench.

5. Thread the

speaker wire

through the

center hole

and out of the

wire opening

on the surface

mount bracket

base. Place

surface mount

bracket base

flush against

the surface you

wish to install

your speaker. To

attach surface

mount bracket

base to the

surface, use

appropriate

screws (not supplied) for your installation. For specifications

on screws, see your dealer for details.

Note: For a wall mounted installation where a wire connection

is contained within the surface mount bracket base, please

follow these instructions. It is recommend that the speaker wire

be cut short and the wire sleeve should be removed to expose

the red (+) and black (-) wires. Follow steps 6 a-b, but do not

attach the assembled speaker with surface mount bracket base

until your wire connections are made with silicone-filled wire

connectors covering the exposed wire connections. The wire

connections with silicone- filled wire connectors must be stuffed

inside the surface mount bracket base before attaching to the

desired surface with appropriate screws (not supplied) for your

installation. For specifications on screws, see your dealer for

details.

For wiring instructions see ‘Speaker &

Burial Cable Connections’ on page 11.

Speaker & Burial Cable Connections

SPEAKER DIRECTION & SETTINGS

1. Aim the speaker by loosening the screw in the speaker

arm and retightening once the desired aim is achieved.

2. Set the dial on every satellite speaker

in your sytem. To access the dial, remove the

rear cap from your satellite speaker by turning a

quarter turn in a counter clockwise direction. Now

pull the cap away from the satellite enclosure.

Set the dial to correspond with the number of

satellite speakers and subwoofers in the installation

(see ‘Audio Settings Chart’ on page 15).

Combine and

twist (clockwise)

the red wires

(as shown in the

diagram) from

the amp, speaker

and to the next

speaker. Secure

these three wires

using the provided

silicone-filled wire

connectors; Repeat procedure for Black wires. NOTE: You

may have to cut some of the speaker cable emanating from

the speaker to a more manageable size.

To Amp

To Adjoining

Speaker

WIRING & SPEAKER INSTALLATION (CONT’D)

8oh

7.5W

3.75W

30W

Following the same instructions outlined for the Ground Stake

or Surface Mount Bracket accessory. The Outdoor Living

Series Inground Conduit Box can be substituted. Knock out

holes in the Inground Conduit Box as needed. Conduit is sold

separately.

Included:

• (1) Inground Conduit Box

• (1) Two Piece Mounting Post

• (8) Stainless Steel Screws

• (4) Ground Stakes

Recommended Tools:

• Drill

• PVC Glue – for PVC conduit or fittings

• Silicone Caulk

• Shovel

• Hammer

• #2 Phillips Screwdriver

• Wrench

Installation Instructions

IMPORTANT! Test your system before

gluing or caulking any part of the

Inground Conduit Box or any conduit

piping connections. Use silicone caulk to seal any

openings used for cable. Allow caulk and glue to dry

completely before burying the Inground Conduit Box.

OPTION 1: PVC Conduit Installation – Knock out the

conduit openings to be used. Glue the conduit piping to the

Inground Conduit Box.* Draw the cable through the conduit

and pull at least 8 inches of cable into the box cavity.

Note: The Inground Conduit Box openings are 3/4” in

diameter. Other conduit piping sizes may be used with adapters.

OPTIONAL INGROUND CONDUIT BOX

OPTIONAL INGROUND CONDUIT BOX (CONT’D)

TEST SYSTEM

OPTION 2: Burial Cable Installation – Drill a hole into

the center of the knock out slightly larger than the cable. Route

the cable through and pull at least 8 inches of cable into

the box cavity. Seal the entrance completely with silicone.*

Place the Inground Conduit Boxes in their appropriate trench

location, ensuring a minimum depth of 6 inches.

3. Install the satellite speaker to the Inground Conduit Box

lid, using the two piece post. Use silicone in the threads

to enhance sealing of the Inground Conduit Box against

moisture.*

4. Use the silicone-filled wire connectors included with the

speaker to terminate the wiring connections. Turn the

silicone-filled wire connectors clockwise by hand until they

are tight.

5. The box may now be closed. A weatherproof gasket is

attached to the cover, but for additional water intrusion

protection, line the inside edge of the cover with silicone

where it contacts the box, then assemble the box using the

8 screws.* Tighten the screws tightly by hand with a #2

screwdriver.

6. Anchor Inground Conduit Box in the hole using the 4

provided stakes. Install all speakers and test the system

before burying the boxes and wiring.

7. Using a screw driver, adjust the speaker angle and

position last.

*See ‘IMPORTANT!’ notice on the previous page.

After all satellites and subwoofer connections are completed,

connect the wires to your receiver or amplifier.

IMPORTANT! Be sure not to let any stray’+’ and’-’

strands touch each other. Touching strands will cause

a short circuit which could damage your amplifier.

Turn your receiver or amplifier ‘On’ and test the system with your

favorite music. If the speakers are operating properly, refill the

wire trench and enjoy your new speakers.

Don’t be fooled by your amplifier’s volume

control. It adjusts listening level—it does not indicate power

output. If your speakers begin to sound harsh or grating,

or if you hear the bass breaking up, turn the volume down

immediately or you will damage your speakers! This type of

damage constitutes abuse and is not covered by the warranty!

Tone controls and equalizers can demand even more power

from an amplifier, lowering the point at which it produces

clipping distortion. Use them sparingly, if at all, and do not

use them when listening at loud levels.

Outdoors there are no walls to contain sound. Background

noise is louder and the distance listeners are from the

speaker(s) is usually greater. Achieving a reasonable listening

level can be more difficult. The tendency is to turn up the

volume, however this may disturb neighbors and when turned

up too high, can seriously damage the speakers or your

amplifier.

The solution? In larger areas we recommend using multiple

MartinLogan Outdoor Living Series speakers. Using more

speakers ensures that sound is evenly distributed, allowing for

reasonable listening levels at lower volumes. Demand on the

amplifier is reduced and neighbors are not disturbed. Think

of it this way: When lighting a large outdoor area, using

multiple floodlights on a dimmer set to a low setting is far

more effective than using a single floodlight with the dimmer

set to high.

TO AVOID SPEAKER DAMAGE

LISTENING OUTDOORS

During the off season, when your speakers are not in use for

prolonged periods, you can cover your speakers from the

elements using the cover included. This cover is breathable,

while protecting your speaker for harsh, inclement weather.

OFF SEASON SPEAKER COVER

AUDIO SETTINGS CHART

LARGE SYSTEM INSTALLATION (8 Ohm SUBS with 70 Volt SATS)

CHANNEL 1

ON CROWN AMP

CHANNEL 2

ON CROWN AMP

PRESET NAME

ON CROWN AMP

POWER OUTPUT

ON CROWN AMP

SETTINGS FOR MARTINLOGAN

SUBWOOFERS AND SPEAKERS

Crown CDi1000

Amplifier

MartinLogan

product

connected to

Amp Channel 1

MartinLogan

product

connected to

Amp Channel 2

Set Crown CDi

1000 amplifier

preset to

Amplifier signal

provided to

speakers

OUTDOOR SUB 100 or 120

Amp Channel 1:

OUTDOOR SUB

subwoofers

plus

Amp Channel 2:

OUTDOOR SAT

speakers

SUB 100 SAT 40 40SAT100

Amp Channel 1:

8 Ohm

Amp Channel 2:

70 Volt

Amp Channel 1:

1–3 subwoofers (sub is always 8 Ohm)*

SUB 100 SAT 60 60SAT100

OUTDOOR SAT 40 or 60

SUB 120 SAT 40 40SAT120

Number of

speakers per

Amp Channel

Setting for SAT

speaker

(remove rear cap

to access dial)

SUB 120 SAT 60 60SAT120

Amp Channels 1 and 2:

OUTDOOR SAT

speaker(s)

SAT 40 (mono) SAT 40 (mono) 40SAT_MO

Amp Channel 1:

70V Volt

Amp Channel 2:

70 Volt

Amp Channel 1 or 2:

1–12 speakers*

70 VOLTS / 30W

(or less)

SAT 60 (mono) SAT 60 (mono) 60SAT_MO

Amp Channel 1 or 2:

13–24 speakers*

70 VOLTS / 15W

(or less)

SAT 40 (stereo)** SAT 40 (stereo)** 40SAT_ST

Amp Channel 1 or 2:

25–49 speakers*

70 VOLTS / 7.5W

(or less)

SAT 60 (stereo)** SAT 60 (stereo)** 60SAT_ST

Amp Channel 1 or 2:

50–100 speakers*

70 VOLTS / 3.8W

(or less)

COMPACT SYSTEM INSTALLATION (8 Ohm SUBS with 8 Ohm SATS)

CHANNEL 1

ON CROWN AMP

CHANNEL 2

ON CROWN AMP

PRESET NAME

ON CROWN AMP

POWER OUTPUT

ON CROWN AMP

SETTINGS FOR MARTINLOGAN

SUBWOOFERS AND SPEAKERS

Crown CDi1000

Amplifier

MartinLogan

product

connected to

Amp Channel 1

MartinLogan

product

connected to

Amp Channel 2

Set Crown CDi

1000 amplifier

preset to

Amplifier signal

provided to

speakers

OUTDOOR SUB 100 or 120

Amp Channel 1:

OUTDOOR SUB

subwoofers

plus

Amp Channel 2:

OUTDOOR SAT

speakers

SUB 100 SAT 40 840ST100

Amp Channel 1:

8 Ohm

Amp Channel 2:

8 Ohm

Amp Channel 1:

1–3 subwoofers (sub is always 8 Ohm)*

SUB 100 SAT 60 860ST100

OUTDOOR SAT 40 or 60

SUB 120 SAT 40 840ST120

Number of

speakers per

Amp Channel

Setting for SAT

speaker

(remove rear cap

to access dial)

SUB 120 SAT 60 860ST120

Amp Channels 1 and 2:

OUTDOOR SAT

speakers

SAT 40 (mono) SAT 40 (mono) 840STMO

Amp Channel 1:

8 Ohm

Amp Channel 2:

8 Ohm

Amp Channel 1 or 2:

1–4 speakers*

8ohm

SAT 60 (mono) SAT 60 (mono) 860STMO

SAT 40 (stereo)** SAT 40 (stereo)** 840SATST

SAT 60 (stereo)** SAT 60 (stereo)** 860SATST

* Using a large number

of speakers per amplifier

channel will result in

lower overall system

volume. Large systems

may benefit from multiple

amplifiers.

** The wiring harness

provided with the

MartinLogan sourced

Crown CDi 1000 amplifier

is configured for mono.

To convert this wiring

harness for stereo, cut the

blue wire on the harness.

* Using a large number

of speakers per amplifier

channel will result in

lower overall system

volume. Large systems

may benefit from multiple

amplifiers.

** The wiring harness

provided with the

MartinLogan sourced

Crown CDi 1000 amplifier

is configured for mono.

To convert this wiring

harness for stereo, cut the

blue wire on the harness.

MartinLogan offers online warranty registration

at www.martinlogan.com.

Your speaker is provided with an automatic Limited 90 Day

Warranty coverage.

You have the option, at no additional charge, to receive a

Limited 3 Year Warranty coverage. To obtain the Limited 3

Year Warranty coverage register your speakers at www.

martinlogan.com. Save a copy of your dealer receipt as it

may be requested if service is required.

MartinLogan may not honor warranty service claims unless

we have a completed Warranty Registration on file at

www.MartinLogan.com!

Should you be using your MartinLogan product in a country

other than the one in which it was originally purchased, we

ask that you note the following:

1. The appointed MartinLogan distributor for any given

country is responsible for warranty servicing only on units

distributed by or through it in that country in accordance

with its applicable warranty.

2. Should a MartinLogan product require servicing in a

country other than the one in which it was originally

purchased, the end user may seek to have repairs

performed by the nearest MartinLogan distributor, subject

to that distributor’s local servicing policies, but all cost of

repairs (parts, labor, transportation) must be borne by the

owner of the MartinLogan product.

3. If, after owning your speakers for six months, you relocate

to a country other than the one in which you purchased

your speakers, your warranty may be transferable. Contact

MartinLogan for details.

LIMITED WARRANTY

SERVICE

SPECIFICATIONS

Frequency Response .......

Recommended Amp Power ..

Recommended Amplifier ....

Maximum Input Power .....

Sensitivity — Outdoor ......

Sensitivity — Anechoic ......

Impedance...............

Crossover................

High Frequency Driver ......

Bass/Midrange Driver ......

Input Controls ............

Ingress Protection Rating ....

Dimensions ..............

Weight..................

Accessories (included).......

OUTDOOR SAT 40

120–20,000 Hz ±3dB

15–120 Watts

Crown CDi 1000 (with MartinLogan

custom DSP settings)

60 Watts

87 dB

83 dB

Compatible with 8 ohms

2,500 Hz

0.75” (1.9cm) aluminum dome, ferro-

fluid cooled tweeter

4” (10 cm) mineral-filled

polypropylene cone

8-Ohm, 70 Volt (3.75W, 7.5W, 15W,

or 30W), 100 Volt (7.5W, 15W, or

30W)

IP54

6” (diameter) x 10” (depth)

(15.2 cm x 25.4 cm)

5 lbs (2.3 kg)

Off season speaker cover

OUTDOOR SAT 60

90–20,000 Hz ±3dB

15–120 Watts

Crown CDi 1000 (with MartinLogan

custom DSP settings)

80 Watts

92 dB

88 dB

Compatible with 8 ohms

2,500 Hz

0.75” (1.9cm) aluminum dome, ferro-

fluid cooled tweeter

6” (16 cm) mineral-filled

polypropylene cone

8-Ohm, 70 Volt (3.75W, 7.5W,

15W, or 30W), 100 Volt (7.5W,

15W, or 30W)

IP54

8.3” (diameter) x 11.3” (depth)

(21 cm x 28.6 cm)

6.5 lbs (3 kg)

Off season speaker cover

DIMENSIONAL DRAWINGS

Detailed dimensional drawings of the entire Outdoor Living

Series are available for download from MartinLogan.com.

Lawrence, Kansas, USA tel 785.749.0133 fax 785.749.5320 www.martinlogan.com

La page charge ...

MartinLogan Outdoor Sat 40 Manuel utilisateur

Marque: MartinLogan

Modèle: Outdoor Sat 40

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: MartinLogan Outdoor Sat 40 User manual

MartinLogan Outdoor Sat 40 Manuel utilisateur

Ce manuel convient également à

MartinLogan Outdoor Sat 40 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents