Black Max BM903650 Series Manuel utilisateur

Marque: Black Max

Modèle: BM903650 Series

Catégorie: Groupes électrogènes

Taper: Manuel utilisateur

OPERATOR’S MANUAL

Manuel de l’opérateur

Manual del operador

3650 WATT GENERATOR

Générateur de 3650 watts

Generador 3650 watts

BM903650 Series

Série BM903650

Serie BM903650

SAVE THIS MANUAL FOR FUTURE REFERENCE

Your generator has been engineered and manufactured to our high standard for dependability, ease of operation, and

operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.

DANGER: You WILL be KILLED or SERIOUSLY HURT if you do not follow the instructions in this operator’s

manual.

Thank you for your purchase.

Ce générateur a été conçu et fabriqué conformément à nos

strictes normes de fiabilité, de simplicité d’emploi et de sécurité

d’utilisation. Correctement entretenu, il vous donnera des années

de fonctionnement robuste et sans problème.

DANGER : Le non-respect des instructions fournies

dans ce manuel d’utilisation entraînera des BLESSURES

GRAVES, voire MORTELLES.

Merci de votre achat.

Su generador ha sido diseñado y fabricado de conformidad con

estrictas normas para brindar fiabilidad, facilidad de uso y seguridad

para el operador. Con el debido cuidado, le brindará muchos años

de sólido y eficiente funcionamiento.

PELIGRO: El incumplimiento de las instrucciones en

este manual del operador puede CAUSARLE LA MUERTE O

LESIONARLE GRAVEMENTE.

Le agradecemos su compra.

CONSERVER CE MANUEL POUR

FUTURE RÉFÉRENCE

GUARDE ESTE MANUAL PARA

FUTURAS CONSULTAS

NEUTRAL BONDED TO FRAME

CONNECTEUR NEUTRE RELIÉ AU CADRE /

PUNTO NEUTRO CONECTADO AL MARCO

CUSTOMER SERVICE

SERVICE CLIENTELE

SERVICIO AL CLIENTE

1-800-726-5760

OFF

MARCHA

APAGADO

SYSTEM MONITOR/MONITOR DEL SYSTEMA

See this fold-out section for all of the figures

referenced in the operator’s manual.

Consulter l’encart à volets afin d’examiner

toutes les figures mentionnées dans le manuel

d’utilisation.

Consulte esta sección desplegable para ver todas

las figuras a las que se hace referencia en el

manual del operador.

iii

OFF

MARCHA

APAGADO

SYSTEM MONITOR/MONITOR DEL SYSTEMA

Fig. 1

A - Recoil starter grip (poignée du démarreur à rappel, mango del arrancador

retráctil)

B - Air filter (filtre à air, filtro de aire)

C - Choke lever (levier d’étrangleur, palanca del anegador)

D - Fuel cap (bouchon de carburant, tapa del tanque)

E - Fuel tank (réservoir de carburant, tanque de combustible)

F - 120 volt AC 20 amp receptacles (prises 120 V C.A. 20 A,

120 V de CA 20 A receptáculos)

G - 120 Volt 30 Amp RV receptacle (prise pour un véhicules récréatifs de 120

V, 30 A; toma receptáculo por vehículos recreativos de 120 V, 30 A)

H - 30 amp AC circuit breaker (30 A disjoncteur de C.A., 30 A disyuntor de

circuito de CA)

I - Engine switch (commutateur du moteur, interruptor del motor)

Fig. 2 Fig. 3

J - Digital display (afficheur numérique, pantalla digital)

K - Oil drainage bolt (vis de vidange d’huile, perno de drenaje de aceite)

- Oil cap/dipstick (bouchon/jauge d’huile, tapa de relleno de aceite/varilla

medidora de aceite)

M - Handle (poignée, mango)

- Ground terminal (borne de terre, terminal de conexión a tierra)

O - Fuel valve (robinet de carburant, válvula de combustible)

P - Muffler (silencieux, silenciador)

Q - 20 amp AC circuit breakers (20 A disjoncteurs de C.A., 20 A disyuntors

de circuito de CA)

R - 120 Volt 30 Amp amp twist lock receptacle (prise à verrouillage par

rotation de 120 V et 30 A; toma de corriente de fijación por giro de 120 V

y 30 A)

A - Bolt (boulon, perno)

B - Support foot (pied de support, pie de soporte)

C - Wing nut (écrou à oreilles, tuerca de mariposa)

D - Frame (cadre, armazón)

E - Washer (rondelle, arandela)

D B

OFF

MARCHA

APAGADO

SYSTEM MONITOR/MONITOR DEL SYSTEMA

120 V 20 A AC

OFF

MARCHA

APAGADO

SYSTEM MONITOR/MONITOR DEL SYSTEMA

Fig. 4

Fig. 6

Fig. 5

Fig. 8

A - Handle bracket (support de la poignée,

abrazadera del mango)

B - Handle (poignée, mango)

C - Hole (trou, agujero)

D - Bolt (boulon, perno)

E - Wing nut (écrou à oreilles, tuerca de mariposa)

A - Handle bracket (support de la poignée,

abrazadera del mango)

B - Bolt (boulon, perno)

C - Wing nut (écrou à oreilles, tuerca de mariposa)

Fig. 11

Fig. 12

Fig. 10

Fig. 9

A - Fuel valve (robinet de carburant, interruptor

del motor)

B - Engine switch (contacteur du moteur, válvula

de combustible)

C - Recoil starter grip (poignée de démarreur à

rappel, mango del arrancador retráctil)

A - Wheel (roue, rueda)

B - Lock Nut (écrou frein, tuerca de bloqueo)

C - Bolt (boulon, perno)

D - Wheel mounting hole (trou du roue, agujero

para rueda)

E - Spacer (écarteur, espaciador)

Fig. 7

A - Oil cap/dipstick (bouchon/jauge d’huile,

tapa de relleno de aceite/varilla medidora de

aceite)

B - Lubricant fill hole (orifice de remplissage

d’huile, agujero de llenado de aceite)

A - Fuel cap (bouchon de carburant, tapa del

tanque de combustible)

B - Fuel tank (réservoir de carburant, tanque de

combustible)

A - Fuel valve (robinet de carburant, válvula de

combustible)

B - Off (arret, apagado)

C - On (marche, encendido)

A - Engine switch (contacteur du moteur, válvula

de combustible)

B - Off (arret, apagado)

C - On (marche, encendido)

A - Move choke lever right to run (pousser droite

le levier d’étranglement pour la marche,

desplace derecha la palanca del anegador

para poner en marcha)

B - Move choke lever left to start (tirer gauche

le levier d’étranglement pour démarrer,

desplace izquierda de la palanca del anegador

para arrancar)

OFF

MARCHA

APAGADO

SYSTEM MONITOR/MONITOR DEL SYSTEMA

OFF

(B)

OFF

(C)

A - Spark plug (bougie, bujía)

B - Spark plug cap (capuchon de bougie, tapa de

la bujía)

Fig. 16

A - Fuel line (conduite de carburant, conducto de

combustible)

B - Fuel valve (robinet de carburant, válvula de

combustible)

C - Petcock (robinet de carburant, llave de

purga)

D - Off (arret, apagado)

E - On (marche, encendido)

A - Carburetor drain screw (vis de vidange

du carburateur, tornillo de drenaje del

carburador)

Fig. 19

Fig. 14

A - Knob (bouton, perilla)

B - Air filter cover (couvercle du filtre à air, tapa del

filtro de aire)

C - Air filter (filtre à air, filtro de aire)

D - Deflector (déflecteur, deflector)

E - Air filter unit (unité de filtre à air, unidad del

filtro de aire)

Fig. 15

A - Oil drainage bolt (vis de vidange d’huile,

perno de drenaje de aceite)

B - Oil cap/dipstick (bouchon/ jauge d’huile,

tapa de relleno de aceite/varilla medidora de

aceite)

Fig. 18

Fig. 13

OFF

(D)

OFF

(E)

Fig. 17

A - Screw (vis, tornillo)

B - Muffler outlet (sortie du silencieux,

recubrimiento del silenciador)

C - Spark arrestor (pare-étincelles, parachispas)

D - Wire brush (brosse métallique, cepillo de

alambre)

A - Fuel line (conduites de carburant, conducto

de combustible)

B - Fuel filter (filtre à carburant, filtro de

combustible)

Fig. 20

A - Select button (bouton de sélection, botón de

selección)

Page 2 — English

DANGER:

GROUNDING THE GENERATOR

To reduce the risk of shock or electrocution, generator must be properly

grounded. The nut and ground terminal on the frame must always be

used to connect the generator to a suitable ground source. The ground

path should be made with #8 size wire. Connect the terminal of the

ground wire between the lock washer and the nut, and tighten the nut

fully. Connect the other end of the wire securely to a suitable ground

source.

The National Electric Code contains several practical ways in which to

establish a good ground source. If a steel or iron rod is used, it should

be at least 5/8 in. diameter, and if a nonferrous rod is used, it should be

at least 1/2 in. diameter and be listed as material for grounding. Drive

the rod or pipe to a depth of 8 ft. If a rock bottom is encountered less

than 4 ft. down, bury the rod or pipe in a trench.

All electrical tools and appliances operated from this generator must

be properly grounded by use of a third wire or be “Double Insulated.”

It is recommended to:

1. Use electrical devices with 3-prong grounded plugs.

2. Use an extension cord with a 3-pole receptacle and a 3-prong plug at opposite ends to ensure continuity of the

ground protection from the generator to the appliance.

Check and adhere to all applicable federal, state, and local regulations relating to grounding specifications. Consult a

qualified electrician or service personnel if the grounding instructions are not completely understood or if in doubt as

to whether the generator is properly grounded.



Introduction .................................................................................................................................................................... 2



Important Safety Instructions .....................................................................................................................................3-4



Specific Safety Rules ..................................................................................................................................................... 4



Symbols ......................................................................................................................................................................5-7



Electrical .....................................................................................................................................................................8-9



Features ...................................................................................................................................................................... 10



Assembly ................................................................................................................................................................11-12



Operation ................................................................................................................................................................13-15



Maintenance ...........................................................................................................................................................16-18



Troubleshooting ........................................................................................................................................................... 19



Warranty ..................................................................................................................................................................20-22



Parts Ordering / Service..................................................................................................................................Back Page

TABLE OF CONTENTS

INTRODUCTION

This product has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability

have been given top priority in the design of this product, making it easy to maintain and operate.

Page 3 — English

IMPORTANT SAFETY INSTRUCTIONS

DANGER:

Carbon Monoxide. Using a generator indoors CAN KILL

YOU IN MINUTES.

Generator exhaust contains high levels of carbon mon-

oxide (CO), a poisonous gas you cannot see or smell. If

you can smell the generator exhaust, you are breathing

CO. But even if you cannot smell the exhaust, you could

be breathing CO.

 Never use a generator inside homes, garages, crawl-

spaces, or other partly enclosed areas. Deadly levels

of carbon monoxide can build up in these areas.

Using a fan or opening windows and doors does NOT

supply enough fresh air.

 ONLY use a generator outdoors and far away from

open windows, doors, and vents. These openings

can pull in generator exhaust.

Even when you use a generator correctly, CO may leak

into the home. ALWAYS use a battery-powered or bat-

tery-backup CO alarm in the home.

If you start to feel sick, dizzy, or weak after the generator

has been running, move to fresh air RIGHT AWAY. See a

doctor. You could have carbon monoxide poisoning.

WARNING:

Read and understand all instructions. Failure to follow

all instructions listed below may result in electrocution,

fire, and/or carbon monoxide poisoning, which will cause

death or serious injury.

WARNING:

National Electric Code requires generator to be grounded

to an approved earth ground. Before using the ground

terminal, consult a qualified electrician, electrical inspec-

tor, or local agency having jurisdiction for local codes

or ordinances that apply to the intended use of the

generator.

SAVE THESE INSTRUCTIONS

This manual contains important instructions that should be

followed during installation and maintenance of the genera-

tor and batteries.



Do not connect to a building’s electrical system unless

the generator and transfer switch have been properly

installed and the electrical output has been verified by

a qualified electrician. The connection must isolate the

generator power from utility power and must comply with

all applicable laws and electrical codes.

 Do not allow children or untrained individuals to use this

unit.

 Never start or run the engine inside a closed or partially

enclosed area. Breathing exhaust fumes will kill you.

 Keep all bystanders, children, and pets at least 10 feet

away.

 Wear sturdy and dry shoes or boots. Do not operate while

barefoot.

 Do not operate generator when you are tired or under the

influence of drugs, alcohol, or medication.

 Keep all parts of your body away from any moving parts

and all hot surfaces of the unit.

 Do not touch bare wire or receptacles.

 Do not use generator with electrical cords which are

worn, frayed, bare, or otherwise damaged.

 Before storing, allow the engine to cool and drain fuel

from the unit.

 Do not operate or store the generator in rain, snow, or

wet weather.

 Store the generator in a well-ventilated area with the fuel

tank empty. Fuel should not be stored near the generator.

 Empty fuel tank, close fuel valve, and restrain the unit

from moving before transporting in a vehicle.

 Allow engine to cool for five minutes before refueling.

 To reduce the risk of fire and burn injury, handle fuel with

care. It is highly flammable.

 Do not smoke while handling fuel.

 Store fuel in a container approved for gasoline.

 Position the unit on level ground, stop engine, and allow

to cool before refueling.

 Loosen fuel cap slowly to release pressure and to keep

fuel from escaping around the cap.

 Tighten the fuel cap securely after refueling.

 Wipe spilled fuel from the unit.

 Never attempt to burn off spilled fuel under any circum-

stances.

 Generators vibrate in normal use. During and after the

use of the generator, inspect the generator as well as

extension cords and power supply cords connected to

it for damage resulting from vibration. Have damaged

items repaired or replaced as necessary. Do not use plugs

or cords that show signs of damage such as broken or

cracked insulation or damaged blades.

 For power outages, permanently installed stationary gen-

erators are better suited for providing back-up power to

the home. Even a properly connected portable generator

can become overloaded. This may result in overheating

or stressing the generator components, possibly leading

to generator failure.

Page 4 — English

SPECIFIC SAFETY RULES

WARNING:

When this generator is used to supply a building

wiring system: generator must be installed by a quali-

fied electrician and connected to a transfer switch as

a separately derived system in accordance with NFPA

70, National Electrical Code. The generator shall be

connected through a transfer switch that switches all

conductors other than the equipment grounding con-

ductor. The frame of the generator shall be connected to

an approved grounding electrode. Failure to isolate the

generator from power utility can result in death or injury

to electric utility workers.



Do not use this generator to provide power for emergency

medical equipment or life support devices.



This generator has a neutral bonded condition. This means

the system ground is connected electrically to the AC

neutral wire.



Exhaust contains poisonous carbon monoxide, a color-

less, odorless gas. Breathing exhaust can cause loss

of consciousness and can lead to death. If running in a

confined or partially-enclosed area, the air may contain

a dangerous amount of carbon monoxide. To keep ex-

haust fumes from building up, always provide adequate

ventilation.



Always use a battery-powered carbon monoxide detec-

tor when running the generator. If you begin to feel sick,

dizzy, or weak while using the generator, shut it off and

get to fresh air immediately. See a doctor. You may have

carbon monoxide poisoning.



Place the generator on a flat, stable surface with a slope

of no more than 4°.



Operate in a well-ventilated, well-lit area isolated from

working areas to avoid noise interference.



Operating the generator in wet conditions could result in

electrocution. Keep the unit dry.



Keep the generator a minimum of 3 feet away from all

types of combustible material.



Do not operate generator near hazardous material.



Do not operate generator at a gas or natural gas filling

station.



Do not touch the muffler or cylinder during or immediately

after use; they are HOT and will cause burn injury.



Do not allow the generator’s gas tank to overflow when

filling. Fill to 1 in. below the top neck of the gasoline tank

to allow for fuel expansion. Do not cover the fuel tank cap

when the engine is running. Covering the fuel tank cap

during use may cause engine failure and/or damage to

the tool.



Do not smoke when filling the generator with gasoline.



Shut down the engine and allow to cool completely before

adding gasoline or lubricant to the generator.



Do not remove the oil dipstick or the fuel tank cap when

the engine is running.



Pay close attention to all safety labels located on the

generator.



Keep children a minimum of 10 feet away from the gen-

erator at all times.



The unit operates best in temperatures between 23°F and

104°F with a relative humidity of 90% or less.



Specific modifications for high-altitude performance are

needed if the generator will always be operated at alti-

tudes above 5,000 feet. Contact your nearest authorized

service center for more information and to have these

modifications performed.



Operating voltage and frequency requirement of all

electronic equipment should be checked prior to plug-

ging them into this generator. Damage may result if the

equipment is not designed to operate within a +/- 10%

voltage variation, and +/- 3 hz frequency variation from

the generator name plate ratings. To reduce the risk of

damage, always have an additional load plugged into the

generator if solid state equipment (such as a television

set) is used. A power line conditioner is recommended

for some solid state applications.



Never operate the generator without a spark arrestor

screen.



For outdoor use only.



Save these instructions. Refer to them frequently and use

them to instruct others who may use this product. If you

loan someone this product, loan them these instructions

also.

 Use only authorized replacement parts and accessories

and follow instructions in the Maintenance section of this

manual. Use of unauthorized parts or failure to follow

maintenance instructions may create a risk of shock or

injury.

 Maintain the unit per maintenance instructions in this

Operator’s Manual.

 Inspect the unit before each use for loose fasteners, fuel

leaks, etc. Replace damaged parts.

IMPORTANT SAFETY INSTRUCTIONS

Page 5 — English

SYMBOLS

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper

interpretation of these symbols will allow you to operate the product better and safer.

SYMBOL NAME DESIGNATION/EXPLANATION

Safety Alert Indicates a potential personal injury hazard.

Read Operator’s Manual

To reduce the risk of injury, user must read and understand

operator’s manual before using this product.

Wet Conditions Alert Do not expose to rain or use in damp locations.

Electric Shock

Failure to use in dry conditions and to observe safe practices can

result in electric shock.

Toxic Fumes

Running generator gives off carbon monoxide, an odorless, color-

less, poison gas. Breathing carbon monoxide can cause nausea,

fainting, or death.

Fire/Explosion

Fuel and its vapors are extremely flammable and explosive. Fire

or explosion can cause severe burns or death.

Hot Surface

To reduce the risk of injury or damage, avoid contact with any hot

surface.

Lifting Hazard

To reduce the risk of serious injury, avoid attempting to lift the

generator alone.

Ground

Consult with local electrician to determine grounding requirements

before operation.

Electrocution

Failure to properly ground generator can result in electrocution,

especially if the generator is equipped with a wheel kit.

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL SIGNAL MEANING

DANGER:

Indicates an imminently hazardous situation, which, if not avoided, will result

in death or serious injury.

WARNING:

Indicates a potentially hazardous situation, which, if not avoided, could result

in death or serious injury.

CAUTION:

Indicates a potentially hazardous situation, which, if not avoided, may result in

minor or moderate injury.

CAUTION:

(Without Safety Alert Symbol) Indicates a situation that may result in property

damage.

Page 6 — English

SYMBOLS

SAFETY LABELS

The information on this page can be found on

the generator. For your safety, please study and

understand all of the labels before starting the

generator.

If any of the labels come off the unit or become

hard to read, contact an authorized service center

for replacement.

 You WILL be KILLED or SERIOUSLY HURT if you

do not follow the Operator’s Manual instructions.

 Risk of Fire. Do not add fuel while the product is

operating.

 Generator is a potential source of electric shock.

Do not expose to moisture, rain, or snow. Do not

operate with wet hands or feet.

 Exhaust contains poisonous carbon monoxide

gas that can cause unconsciousness or DEATH.

Operate in well-ventilated, outdoor areas away

from open windows or doors.

 Failure to properly ground generator can result

in electrocution, especially if the generator is

equipped with a wheel kit.

 Do not expose to rain or use in damp locations.

 Using a generator indoors CAN KILL YOU IN

MINUTES. Generator exhaust contains carbon

monoxide. This is a poison you cannot see or smell.

 NEVER use inside a home or garage, EVEN IF

doors and windows are open.

 Only use OUTSIDE and far away from windows,

doors, and vents.

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper

interpretation of these symbols will allow you to operate the product better and safer.

SYMBOL NAME DESIGNATION/EXPLANATION

V Volts Voltage

A Amperes Current

Hz Hertz Frequency (cycles per second)

W Watt Power

hrs Hours Time

gal Gallon Volume

qt Quart Volume

DANGER

PELIGRO

L’utilisation d’une génératrice à l’intérieur PEUT VOUS

TUER ENQUELQUES MINUTES.

Les génératrices produisent du monoxyde de carbone,

un gaz mortel incolore et inodore.

NE JAMAIS utiliser à l’intérieur d’une maison ou d’un

garage,MÊME SI les portes et les fenêtres sont ouvertes.

Utiliser uniquement À L’EXTÉRIEUR et loin des fenêtres,

des portes et des évents.

Usar un generador en el interior PUEDE MATARLO EN

POCOS MINUTOS.

Los gases de escape del generador contienen monóxido

de carbono. Es un veneno que no puede verse ni olerse.

NUNCA lo use dentro de su hogar o del garaje, INCLUSO

con las puertas y las ventanas abiertas.

Sólo utilícelo AL AIRE LIBRE y lejos de ventanas, puertas

y respiraderos.

Using a generator indoors CAN KILL YOU IN MINUTES.

Generator exhaust contains carbon monoxide. This is a

poison you cannot see or smell.

NEVER use inside a home

or garage, EVEN IF doors

and windows are open.

Only use OUTSIDE and

far away from windows,

doors, and vents.

Page 7 — English

SYMBOLS

FUEL WARNING

No smoking when filling with gasoline.

Do not overfill. Full level is 1 in. below

the top of the fuel neck. Stop the en-

gine for five minutes before refueling to

avoid the heat from the muffler igniting

fuel vapors.

ENGINE LUBRICANT WARNING

You must add lubricant before first op-

erating the generator. The oil reservoir

capacity is .64 qt. Always check the

lubricant level before each operation.

The lubricant level should always register

between the hatched areas on the dip-

stick. The unit is equipped with a sensor

which will automatically shut off the engine if the lubricant level

falls below a safe limit.

SPARK ARRESTOR

Operation of this equipment may create sparks that can start

fires around dry vegetation. A spark arrestor may be required.

The operator should contact local fire agencies for laws or

regulations relating to fire prevention requirements.

GROUNDING WARNING

National Electric Code requires generator to be grounded to an approved

earth ground.

HOT SURFACE WARNING

Do not touch the muffler or aluminum cylin-

der of the engine. They are very HOT and will

cause severe burns. Don’t put any flammable

or combustible materials in the direct path of

the exhaust.

El uso de este equipo puede producir chispas propensas a

iniciar incendios cerca de vegetación seca. Es posible que se necesite un parachis-

pas. El operador debe ponerse en contacto con las agencias contra incendios locales

para conocer las leyes y regulaciones relacionadas con los requisitos de prevención

de incendios.

Page 8 — English

ELECTRICAL

EXTENSION CORD CABLE SIZE

Refer to the table below to ensure the cable size of the extension cords you use are capable of carrying the required load.

Inadequate size cables can cause a voltage drop, which can damage the appliance and overheat the cord.

Current in

Amperes

Load in Watts Maximum Allowable Cord Length

At 120V #8 Wire #10 Wire #12 Wire #14 Wire #16 Wire

2.5 300 1000 ft. 600 ft. 375 ft. 250 ft.

5 600 500 ft. 300 ft. 200 ft. 125 ft.

7.5 900 350 ft. 200 ft. 125 ft. 100 ft.

10 1200 250 ft. 150 ft. 100 ft. 50 ft.

15 1800 150 ft. 100 ft. 65 ft.

20 2400 175 ft. 125 ft. 75 ft.

25 3000 150 ft. 100 ft.

30 3600 125 ft. 65 ft.

40 4800 90 ft.

ELECTRIC MOTOR LOADS

It is characteristic of common electric motors in normal operation to draw up to six times their running current while start-

ing. This table may be used to estimate the watts required to start “Code G” electric motors; however, if an electric motor

fails to start or reach running speed, turn off the appliance or tool immediately to avoid equipment damage. Always check

the requirements of the tool or appliance being used compared to the rated output of the generator.

Motor Size (H.P.) Running Watts

Watts Required to Start Motor

Repulsion Induction Capacitor Split Phase

1/8 275 600 850 1200

1/6 275 600 850 2050

1/4 400 850 1050 2400

1/3 450 975 1350 2700

1/2 600 1300 1800 3600

3/4 850 1900 2600 —

1 1100 2500 3300 —

CAUTION:

Operating voltage and frequency requirement of all electronic equipment should be checked prior to plugging them

into this generator. Damage may result if the equipment is not designed to operate within a +/- 10% voltage variation,

and +/- 3 hz frequency variation from the generator name plate ratings. To avoid damage, always have an additional

load plugged into the generator if solid state equipment (such as a television set) is used. A power line conditioner is

recommended for some solid state applications.

Page 9 — English

ELECTRICAL

GENERATOR CAPACITY

Make sure the generator can supply enough continuous (run-

ning) and surge (starting) watts for the items you will power

at the same time. Follow these simple steps.

1. Selecttheitemsyouwillpoweratthesametime.

2. Totalthecontinuous(running)wattsoftheseitems.This

is the amount of power the generator must produce to

keep the items running. See the wattage reference chart

at right.

3. Estimatehowmanysurge(starting)wattsyouwillneed.

Surge wattage is the short burst of power needed to

start electric motor-driven tools or appliances such as a

circular saw or refrigerator. Because not all motors start

at the same time, total surge watts can be estimated by

adding only the item(s) with the highest additional surge

watts to the total rated watts from step 2.

Example:

Tool or Appliance

Continuous

(Running) Watts

Surge

(Starting) Watts

Window AC,

10,000 BTU

1200 1800

Refrigerator 700 2200

1/3 HP Well Pump 1000 2000

27 in. Television 500 0

Light (75 Watts) 75 0

3475 Total

Running Watts

2200 Highest

Surge Watts

Total Continuous (Running) Watts 3475

Plus Highest Additional Surge Watts + 2200

Equals Total Generator Output Required 5675

POWER MANAGEMENT

To prolong the life of the generator and attached devices,

it is important to take care when adding electrical loads to

the generator. There should be nothing connected to the

generator outlets before starting its engine. The correct and

safe way to manage generator power is to sequentially add

loads as follows:

1. With nothing connected to the generator, start the engine

as described later in this manual.

2. Plug in and turn on the first load, preferably the largest

load you have.

3. Permit the generator output to stabilize (engine runs

smoothly and attached device operates properly).

4. Plug in and turn on the next load.

5. Again, permit the generator to stabilize.

6. Repeat steps 4 and 5 for each additional load.

Never add more loads than the generator capacity. Take

special care to consider surge loads in generator capacity

as previously described.

CAUTION:

Do not overload the generator’s capacity. Exceeding the

generator’s wattage/amperage capacity can damage the

generator and/or electrical devices connected to it.

Application/Equipment

Estimated

Run Watts

Estimated

Starting

Watts

Emergency / Home Standby

Clock Radio 50 50

Lights (qty. 4 x 75 W) 300 300

Refrigerator 700 2200

Furnace Fan 800 2350

Water Well Pump 1000 1500

Microwave 1000 1000

Sump Pump 1050 2200

Electric Range (per element) 2100 2100

Job Site

ElectricDrill−1/2HP 600 900

AirlessSprayer−1/3HP 600 1200

Quartz Halogen Work Light 1000 1000

Reciprocating Saw 960 1920

AirCompressor−1HP 1600 4500

CircularSaw−7-1/4in. 1400 2300

Planer/Jointer−6in 1800 1800

MiterSaw−10in. 1800 1800

TableSaw/RadialArmSaw−10in. 2000 2000

*Wattages listed are approximate. Check tool or appliance for actual wattage.

Page 10 — English

FEATURES

PRODUCT SPECIFICATIONS

ENGINE

Engine Type ......................................................208 cc OHV

Cooling System ...................................................Forced Air

Starting System ......................................................... Recoil

Ignition System ............................................................T.C.I.

Spark Plug .......................................................NGK BP6ES

Engine Lubricant Volume.......................................0.64 qts.

Fuel Volume ................................................................ 4 gal.

GENERATOR

Rated Voltage ..............................................................120V

Rated Amps ...............................................................30.4 A

Rated Running Watts* ............................................3,650 W

Rated Starting Watts ..............................................4,550 W

Rated Frequency ........................................................60 Hz

DIMENSIONS

Length ........................................................................ 24 in.

Width .......................................................................... 17 in.

Height ......................................................................... 18 in.

Weight .................................................................... 105 lbs.

KNOW YOUR GENERATOR

See Figure 1.

The safe use of this product requires an understanding of the

information on the product and in this operator’s manual as

well as a knowledge of the project you are attempting. Before

use of this product, familiarize yourself with all operating

features and safety rules.

AC CIRCUIT BREAKERS

The circuit breakers are provided to protect the generator

against electrical overload. The circuit breaker may be reset

by pressing the circuit breaker reset button.

AIR FILTER

The air filter helps to limit the amount of dirt and dust drawn

into the unit during operation.

CHOKE LEVER

The choke lever is used when starting the engine.

DIGITAL DISPLAY

The digital display shows AC voltage output, frequency, how

long the engine has been running during the current usage

period, and the total number of hours the unit has been used.

FUEL TANK

The fuel tank has a capacity of 4 gallons.

FUEL VALVE

The flow of fuel through the generator is controlled by the

position of the fuel valve.

GROUND TERMINAL

The ground terminal is used to assist in properly ground-

ing the generator to help protect against electrical shock.

Consult with a local electrician for grounding requirements

in your area.

OIL CAP/DIPSTICK

Remove the oil cap/dipstick to check and add lubricant to

the generator when necessary.

LOW LUBRICANT SENSOR

The engine will automatically shut off whenever the lubricant

level in the engine becomes low.

OIL DRAINAGE BOLT

When changing the engine lubricant, the oil drainage bolt is

removed to allow old engine lubricant to be drained.

RECEPTACLES

Your generator has the following single phase, 60 Hz outlets:

two 120 V AC/20 amp receptacles, one 120 V AC/30 amp twist

lock receptacle, and one 120 V AC/30 amp RV receptacle.

These can be used for operating appropriate appliances,

electrical lighting, tools, and motor loads.

RECOIL STARTER GRIP

The recoil starter grip is used (along with the engine switch)

to start the generator’s engine.

*Rated running watts determined by PGMA Standard G200

Page 11 — English

ASSEMBLY

WARNING:

Do not attempt to operate the generator until assembly

is complete. Failure to comply could result in possible

serious personal injury.

LOOSE PARTS LIST

See Figure 2.

The following items are included with the generator:

Key

No. Description Qty.

1 Bolts (1/4-20 x 2 mm) ..........................................2

2 Wing Nuts (1/4-20) ..............................................5

3 Wheels .................................................................2

4 Bolts (3/8 x 16 mm) .............................................2

5 Support Feet ........................................................2

6 Handle .................................................................1

7 Washer (1/4-20) ...................................................2

8 Spacer .................................................................2

9 Handle Bracket ....................................................1

10 Bolts (1/4-20 x 1.5 mm) .......................................3

11 Lock Nut (3/8) ......................................................2

12 Bottle of Engine Lubricant ...................................1

Operator’s Manual (not shown) ...........................1

UNPACKING

This product requires assembly.

 Carefully cut the box down the sides then remove the

machine and any accessories from the box. Make sure

that all items listed in the packing list are included.

NOTE: This machine is heavy and requires a minimum of

two people to lift. To avoid back injury, lift with your legs

and not your back.

WARNING:

Do not use this product if any parts on the Loose Parts

List are already assembled to your product when you

unpack it. Parts on this list are not assembled to the

product by the manufacturer and require customer instal-

lation. Use of a product that may have been improperly

assembled could result in serious personal injury.

 Inspect the unit carefully to make sure no damage oc-

curred during shipping.

 Do not discard the packing material until you have

carefully inspected and satisfactorily operated the

product.

 If any parts are damaged or missing, please call customer

service for assistance.

WARNING:

If any parts are damaged or missing do not operate

this product until the parts are replaced. Use of this

product with damaged or missing parts could result in

serious personal injury.

WARNING:

Do not attempt to modify this product or create acces-

sories not recommended for use with this product. Any

such alteration or modification is misuse and could result

in a hazardous condition leading to possible serious per-

sonal injury.

WARNING:

Do not attempt to operate the generator until assembly

is complete. Failure to comply could result in possible

serious personal injury.

NOTE: Do not put fuel or lubricant in the generator before

installing the feet and wheels.

INSTALLING FEET

See Figure 3.

 Raise the end of the generator where the recoil starter is

located high enough to gain access to the frame bottom;

securely position props underneath to support.

 Locate the following items:

2 Support Feet

2 Wing Nuts (1/4-20)

2 Washers (1/4-20)

2 Bolts (1/4-20 x 2 mm)

 Insert bolt through the foot and frame as shown.

 Slide washer onto the bolt and install wing nut. Tighten

securely.

 Repeat with remaining foot.

INSTALLING THE WHEELS

See Figure 4.

Wheels are provided to assist in moving the generator to the

desired location and should be installed on the same side

as the recoil starter.

 Locate the following items:

2 Wheels

2 Bolts (3/8 x 16 mm)

2 Spacers

2 Lock Nuts (3/8)

Page 12 — English

ASSEMBLY

 Raise the end of the generator on the side opposite the

recoil starter to gain access to the frame bottom; securely

position props underneath to support.



Insert a wheel spacer into the center of the wheel.



Slide bolt through the wheel spacer, then through the

wheel mounting hole on the frame.



Install nut on bolt and tighten securely.



Repeat the process on the other side to install second

wheel.

INSTALLING THE HANDLE BRACKET

See Figure 5.

 Locate the following items:

Handle Bracket

2 Bolts (1/4-20 x 1.5 mm)

2 Wing Nuts (1/4-20)

 Place the handle bracket on the generator frame on the

side where the recoil starter is located.

 Slide the bolts (1/4-20 x 1.5 mm) through the holes in the

handle bracket and generator frame; install wing nuts and

tighten securely.

ATTACHING THE HANDLE ASSEMBLY

See Figure 6.

 Locate the following items:

Handle

1 Bolt (1/4-20 x 1.5 mm)

1 Wing Nut (1/4-20)

 Place the handle on the handle bracket.

 Slide the bolt (1/4-20 x 1.5 mm) through the handle and

handle bracket; install wing nut and tighten securely.

WARNING:

Do not attempt to lift the unit by the handle assembly. If

it is necessary to lift the generator, always grasp by the

frame. Use proper lifting techniques to avoid back injury.

Page 13 — English

DANGER:

Carbon Monoxide. Using a generator indoors CAN KILL

YOU IN MINUTES.

Generator exhaust contains high levels of carbon mon-

oxide (CO), a poisonous gas you cannot see or smell. If

you can smell the generator exhaust, you are breathing

CO. But even if you cannot smell the exhaust, you could

be breathing CO.

 Never use a generator inside homes, garages, crawl-

spaces, or other partly enclosed areas. Deadly levels

of carbon monoxide can build up in these areas. Us-

ing a fan or opening windows and doors does NOT

supply enough fresh air.

 ONLY use a generator outdoors and far away from

open windows, doors, and vents. These openings

can pull in generator exhaust.

Even when you use a generator correctly, CO may

leak into the home. ALWAYS use a battery-powered or

battery-backup CO alarm in the home.

If you start to feel sick, dizzy, or weak after the generator

has been running, move to fresh air RIGHT AWAY. See a

doctor. You could have carbon monoxide poisoning.

DANGER:

Failure to properly ground generator can result in elec-

trocution, especially if the generator is equipped with a

wheel kit. National Electric Code requires generator to be

properly grounded to an approved earth ground. Call an

electrician for local grounding requirements.

WARNING:

Do not allow familiarity with this product to make you

careless. Remember that a careless fraction of a second

is sufficient to inflict serious injury.

WARNING:

Do not use any attachments or accessories not

recommended by the manufacturer of this product. The

use of attachments or accessories not recommended

can result in serious personal injury.

Before each use, inspect the entire product for damaged,

missing, or loose parts such as screws, nuts, bolts, caps, etc.

Tighten securely all fasteners and caps and do not operate

this product until all missing or damaged parts are replaced.

Please contact an authorized service center for assistance.

APPLICATIONS

This generator is designed to supply electrical power for

operating compatible electrical lighting, appliances, tools,

and motor loads.

BEFORE OPERATING THE UNIT

 Only use OUTSIDE and far away from windows, doors,

and vents.

 NEVER use inside a home or garage, EVEN IF doors and

windows are open.

 Always position the generator on a flat firm surface.

SPECIAL REQUIREMENTS:

There may be General or State Occupational Safety and

Health Administration (OSHA) regulations, local codes or

ordinances that apply to the intended use of the generator.

Please consult a qualified electrician, electrical inspector, or

the local agency having jurisdiction:

 In some areas, generators are required to be registered

with local utility companies.

 If the generator is used at a construction site, there may

be additional regulations which must be observed.

CAUTION:

Attempting to start the engine before it has been properly

filled with lubricant will result in equipment failure.

CHECKING/ADDING LUBRICANT

See Figure 7.

Engine lubricant has a major influence on engine perfor-

mance and service life. For general, all-temperature use,

SAE 10W-30 is recommended. Always use a 4-stroke motor

lubricant that meets or exceeds the requirements for API

service classification SJ.

NOTE: Non-detergent or 2-stroke engine lubricants will

damage the engine and should not be used.

 Unscrew the oil cap/dipstick and remove.

OPERATION

Page 14 — English

OPERATION

 Wipe dipstick clean and re-seat in hole; do not re-thread.

 Remove dipstick again and check lubricant level. Lubri-

cant level should fall between the hatched areas on the

dipstick.

 If level is low, add engine lubricant until the fluid level rises

to the upper portion of the dipstick.

 Replace and secure the oil cap/dipstick.

CHECKING/ADDING FUEL

See Figure 8.

 Remove the fuel cap.

 Fill the fuel tank to 1 in. below the top of the fuel neck.

 Replace and secure the fuel cap.

NOTE: Always use unleaded gasoline with a pump octane

rating of 86 or higher. Never use old, stale, or contaminated

gasoline, and do not use an oil/gas mixture. Do not allow

dirt or water into the fuel tank.

USING FUEL STABILIZER

Fuel gets old, oxidizes, and breaks down over time. Adding

a fuel stabilizer (not included) extends the usable life of fuel

and helps prevent deposits from forming that can clog the

fuel system. Follow fuel stabilizer manufacturer’s directions

for correct ratio of stabilizer to fuel.

 Add stabilizer to fuel tank, then fill with gasoline following

previous instructions.

NOTE: Fuel stabilizer and gasoline can be mixed prior

to filling the tank by using a gas can or other approved

fuel container and shaking gently to combine.

 Replace and secure the fuel tank cap.

 Start and run the engine for at least 5 minutes to allow

stabilizer to treat the entire fuel system.

OXYGENATED FUELS

DO NOT USE E85 FUEL. IT WILL VOID YOUR

WARRANTY.

NOTE: Fuel system damage or performance problems re-

sulting from the use of an oxygenated fuel containing more

than the percentages of oxygenates stated previously are

not covered under warranty.

Ethanol. Gasoline containing up to 10% ethanol by volume

(commonly referred to as E10) is acceptable. E85 is not.

CAUTION:

On a level surface with the engine off, check the lubricant

level before each use of the generator.

STARTING THE ENGINE

See Figures 9 - 11.

NOTE: If location of generator is not level, the unit may not

start or may shut down during operation.

 Unplug all loads from the generator.

 Turn the fuel valve to the ON position.

 Move the choke lever left to the START position.

NOTE: If engine is warm or the temperature is above

50˚F,movethechokeleverrighttotheRUNposition.

 Put the engine switch in the ON ( I ) position.

 Pull the recoil starting grip until the engine runs (a maxi-

mum of 6 times).

NOTE: Do not allow the grip to snap back after starting;

return it gently to its original place.

 Allow the engine to run for 30 seconds, then move the

choke lever right to the RUN position.

Page 15 — English

OPERATION

STOPPING THE ENGINE

See Figures 10 and 12.

To stop the engine under normal operating conditions:

 Remove any load from the generator.

 Turn the fuel valve to the OFF position.

 Put the engine switch in the OFF position.

To stop the engine in an emergency situation:

 Put the engine switch in the OFF position.

WARNING:

While operating and storing, keep at least 3 feet of clear-

ance on all sides of this product, including overhead.

Allow a minimum of 30 minutes of “cool down” time be-

fore storage. Heat created by muffler and exhaust gases

may be hot enough to cause serious burns and/or ignite

combustible objects.

UNDERSTANDING THE DIGITAL DISPLAY

See Figure 13.

The digital display shows AC voltage output, frequency, how

long the engine has been running during the current usage

period, and the total number of hours the unit has been used.

To cycle through these displays, press the select button. The

(information type) on the digital display will light in sequence

to show which type of information is being displayed.

Hour meter: The hour meter keeps track of how many hours

the unit has been running during the current operation as

well as the total number of hours the unit has been used.

AC voltage: When selected, the AC voltage indicator will

display the generator’s voltage output.

Frequency: When selected, the frequency indicator shows

the generator’s output frequency.

MOVING THE GENERATOR

 Turn the engine switch OFF. Disconnect any equipment

that is plugged into the generator.

 Turn the fuel valve to the OFF position.

 Allow 30 minutes of “cool down” time before storing the

machine.

 Tilt the machine away from you until it balances on the

wheels, then roll the machine to the desired location.

Page 16 — English

WARNING:

When servicing, use only identical Black Max replace-

ment parts. Use of any other parts may create a hazard

or cause product damage.

WARNING:

Always wear eye protection with side shields marked to

comply with ANSI Z87.1. Failure to do so could result in

objects being thrown into your eyes, resulting in possible

serious injury.

Only the parts shown on the parts list are intended to be

repaired or replaced by the customer. All other parts should

be replaced at an authorized service center.

GENERAL MAINTENANCE

Before each use, inspect the entire product for damaged,

missing, or loose parts such as screws, nuts, bolts, caps, etc.

Tighten securely all fasteners and caps and do not operate

this product until all missing or damaged parts are replaced.

Please contact an authorized service center for assistance.

Keep the generator in a clean and dry environment where it

is not exposed to dust, dirt, moisture, or corrosive vapors.

Do not allow the cooling air slots in the generator to become

clogged with foreign material such as leaves, etc.

Do not use a garden hose to clean the generator. Water en-

tering the fuel system or other internal parts of the unit can

cause problems that will decrease the life of the generator.

To clean the unit:

 Use a soft bristle brush and/or vacuum cleaner to loosen

and remove dirt and debris.

 Clean air vents with low pressure air that does not exceed

25 psi.

 Wipe the exterior surfaces of the generator with a damp

cloth.

CHECKING/CLEANING AIR FILTER

See Figure 14.

For proper performance and long life, keep air filter clean.

 Loosen the knob on the bottom of the air filter cover.

Remove cover and set aside.

 Remove the air filter.

 Remove the deflector. Wipe with a clean cloth and replace

in the air filter unit.

 If the air filter is dirty, wash it with warm, soapy water.

Rinse and squeeze to dry.

MAINTENANCE

 Apply a light coat of engine lubricant to the air filter, then

squeeze it out.

 Replace the air filter.

 Replace the air filter cover and tighten knob to secure.

NOTE: Do not run the generator without the air filter or

gasket. Rapid engine wear will result.

CHANGING ENGINE LUBRICANT

See Figure 15.

 Remove the oil cap/dipstick.

 Place a container underneath the oil drainage bolt to

collect used lubricant as it drains.

 Unscrew the oil drainage bolt and remove.

 Allow lubricant to drain completely.

 Reinstall the oil drainage bolt and tighten securely.

 Refill with lubricant following the instructions in the

Checking/Adding Lubricant section.

 Reinstall the oil cap/dipstick.

NOTE: Used lubricant should be disposed of at an approved

disposal site. See your local oil retailer for more information.

SPARK PLUG MAINTENANCE

See Figure 16.

The spark plug must be properly gapped and free of deposits

in order to ensure proper engine operation. To check:

 Remove the spark plug cap.

 Clean any dirt from around base of spark plug.

 Remove spark plug using wrench (not included).

 Inspect spark plug for damage, and clean with a wire

brush before reinstalling. If insulator is cracked or chipped,

spark plug should be replaced.

NOTE: If replacing, use the following recommended spark

plug or equivalent: NGK BP6ES.

 Measurepluggap.Thecorrectgapis0.028−0.031in.

(0.7-0.8 mm). To widen gap, if necessary, carefully bend

the ground (top) electrode. To lessen gap, gently tap

ground electrode on a hard surface.

 Seat spark plug in position; thread in by hand to prevent

cross-threading.

 Tighten with wrench to compress washer. If spark plug

is new, use 1/2 turn to compress washer appropriate

amount. If reusing old spark plug, use 1/8 to 1/4 turn for

proper washer compression.

NOTE: An improperly tightened spark plug will become

very hot and could damage the engine.

La page charge ...

Black Max BM903650 Series Manuel utilisateur

Marque: Black Max

Modèle: BM903650 Series

Catégorie: Groupes électrogènes

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Black Max BM903650 Series User manual
español: Black Max BM903650 Series Manual de usuario

Black Max BM903650 Series Manuel utilisateur

Black Max BM903650 Series Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents