Pitco 45C+, 122K BTU Manuel utilisateur

Marque: Pitco

Modèle: 45C+, 122K BTU

Catégorie: Friteuses

Taper: Manuel utilisateur

Ce manuel convient également à

35C+, 90K BTU

Installation, Operation, and Maintenance Manual

For Gas Fryers

Covering Models

45C+, 35C+ and 40C+, 65

Pitco Frialator, Inc., P.O. Box 501, Jct I-89 & I-93 Concord, NH 03302-0501 • 509 Route 3A, Bow, NH 03304

(603) 225-6684 • FAX (603) 225-8497

L20-072 Rev 7 (01/13)

ENGLISHFRANCAIS

NOTICES

There are three different types of notices that you should be familiar with, a NOTICE, CAUTION,

and WARNING. A NOTICE is a special note used to call attention to a particularly important point.

CAUTION is used to point out a procedure or operation which may cause equipment damage. The

WARNING notice is the most important of the three because it warns of an operation that may cause

personal injury. Please familiarize yourself with your new cooker before operating it and heed the

notices throughout this manual. The WARNINGS are listed below and on the following page for your

review prior to operating the unit.

FOR YOUR SAFETY

DO NOT store or use gasoline or other flammable

vapors or liquids in the vicinity of this or any other

appliance.

WARNING: Improper installation, adjustment, alter-

ation, service or maintenance can cause property dam-

age, injury or death. Read the installation, operating

and maintenance instructions thoroughly before in-

stalling or servicing this equipment.

TO THE PURCHASER

POST IN A PROMINENT LOCATION INSTRUCTIONS TO

BE FOLLOWED IN THE EVENT THAT AN OPERATOR

SMELLS GAS. OBTAIN THIS INFORMATION FROM YOUR

LOCAL GAS SUPPLIER.

THIS MANUAL MUST BE RETAINED FOR FUTURE REFERENCE

ENGLISH

SAFETY SAFETY SAFETY SAFETY SAFETY

WARNING

The cooker must be electrically grounded in accordance with local

codes. If local codes do not apply, follow the requirements of

National Code ANSI/NFPA 70-1990.

WARNING

This cooker is equipped with a three prong safety plug. This safety plug

protects operators from electrical shock in the event of an equipment malfunc-

tion. DO NOT remove the grounding (third) prong from this plug.

WARNING

DO NOT use an open flame to check for gas leaks!

WARNING

A cooker that is equipped with casters and a flexible power cord must be

connected to the gas supply with a Quick-Disconnect device. This quick

disconnect must comply with ANSI Z24.41-1989. A restraining cable must

be installed to limit the movement of the cooker.

WARNING

There is an open gas flame inside the cooker. The unit may get hot enough

to set nearby materials on fire. Keep the area around the cooker free from

combustible materials.

WARNING

Ensure that the cooker can get enough air to keep the flame burning correctly.

If the flame is starved for air it can give off dangerous carbon monoxide.

Carbon Monoxide is a clear odorless gas that can cause suffocation and death.

WARNING

Be sure the burner tubes are COMPLETELY covered with water before

lighting the pilot or main burners. If the tubes are exposed, the cooker may

overheat, causing damage to the kettle, creating a fire hazard, and voiding the

warranty.

SAFETY SAFETY SAFETY SAFETY SAFETY

THIS MANUAL MUST BE RETAINED FOR FUTURE REFERENCE

SAFETY SAFETY SAFETY SAFETY SAFETY

WARNING

Carbon monoxide can build up if the flue is blocked. Blocking the flue will

also cause the cooker to overheat. Ensure that minimum clearances specified

in the installation instructions are maintained. DO NOT obstruct the flow of

combustion/ventilation or air opening around the Noodle Cooker. Adequate

clearance around the cooker is necessary for servicing and proper burner

operation. Ensure that you meet the minimum clearances specified in the

installation instructions.

WARNING

The power supply must be disconnected before servicing or cleaning the

appliance.

WARNING

For gas cookers, DO NOT supply the cooker with a gas that is not listed on

the data plate. If you need to convert the cooker to another type of fuel, contact

your dealer.

WARNING

For gas cookers, WAIT five (5) minutes before attempting to relight the pilot.

This allows time for any gas remaining in the cooker to dissipate.

ENGLISH

Table of Contents

Section Title Page

Table of Contents ............................................................................................................................................i

List of Tables and Figures ...................................................................................................................................ii

Chapter 1: General Information and Installation ..................................................................................... 1-1

1.1 WHICH FRYER DO I HAVE? .................................................................................................. 1-1

1.2 CHECKING YOUR NEW FRYER............................................................................................ 1-1

1.2.1 Check Your Order ................................................................................................................ 1-2

1.3 ASSEMBLY AND LEVELING ................................................................................................. 1-2

1.3.1 Leg/Caster Installation and Adjustment ............................................................................... 1-2

1.3.2 Assembling Multi Fryer Systems ......................................................................................... 1-3

1.4 INSTALLATION........................................................................................................................ 1-3

1.4.1 Installation Clearances.......................................................................................................... 1-3

1.4.2 Gas Connection .................................................................................................................... 1-3

1.4.2.1 Fuel Types ..................................................................................................................... 1-4

1.4.2.2 Gas Line Connection ..................................................................................................... 1-4

1.4.2.3 Quick Disconnect Gas Connection................................................................................ 1-4

1.4.2.4 Fuel Supply Line Leak and Pressure Testing ................................................................ 1-5

1.4.3 Ventilation and Fire Safety Systems .................................................................................... 1-5

1.5 INITIAL ADJUSTMENTS......................................................................................................... 1-5

1.5.1 Visual Checks....................................................................................................................... 1-6

1.5.2 Burner Ignition Systems ....................................................................................................... 1-6

1.5.2.1 Pilot Flame Adjustment ................................................................................................. 1-7

1.5.3 Main Burner System............................................................................................................. 1-8

1.5.3.1 Gas Line Requirements.................................................................................................. 1-8

1.5.3.2 Burner Adjustment ........................................................................................................ 1-8

1.5.4 Initial Cleaning ..................................................................................................................... 1-9

1.5.5 Thermostat Calibration Check............................................................................................ 1-10

1.5.6 Thermostat Calibration ....................................................................................................... 1-11

Chapter 2: Operating Instructions ............................................................................................................. 2-1

2.1 FILLING THE FRYER............................................................................................................... 2-1

2.1.1 Filling the Fryer With Liquid Shortening ............................................................................. 2-1

2.1.2 Filling the Fryer With Solid Shortening ............................................................................... 2-1

2.2 OPERATING INSTRUCTIONS ................................................................................................ 2-2

2.2.1 Fryer Start-Up....................................................................................................................... 2-2

2.2.2 Melting Solid Shortening...................................................................................................... 2-2

2.2.3 Fryer Shutdown .................................................................................................................... 2-3

2.3 DAILY CLEANING................................................................................................................... 2-3

Chapter 3: Owner Maintenance and Adjustments ................................................................................... 3-1

3.1 WEEKLY FRYER CLEANING (BOIL OUT) .......................................................................... 3-1

3.2 FLUE INSPECTION .................................................................................................................. 3-1

3.3 TROUBLESHOOTING.............................................................................................................. 3-2

ENGLISH

List of Tables and Figures

Table Title Page

1-1 Fryer Model Information ................................................................................. 1-1

1-2 Ventilation and Fire Safety References.............................................................. 1-7

Figure Title Page

1-1 Pilot Assembly, Flame Adjustment................................................................... 1-8

1-2 Gas Valve Showing Location of Pressure Regulator and Pilot Adjusters............... 1-9

1-1

Chapter 1: General Information and Installation

Congratulations on the purchase of your new Pitco Frialator universal fryer. This unit will give

you many years of reliable service if you follow the simple operation and maintenance

procedures in this manual. Contained in this manual are the general installation, operation, and

maintenance procedures for the universal fryer Models 45C+, 35C+ 40C+, and 65C+.

1.1 WHICH FRYER DO I HAVE?

There are two models of this gas fryer available. Each fryer has its own model number. To find

out which model you have, look inside the door at the equipment identification plate. This plate

has a lot of useful information, but to identify which fryer you have, look at the model number

block. The model number identifies which fryer you have. A brief description of each model

is provided inTable 1-1.

Table 1-1 Fryer Model Information

Model

Number

45C+

35C+

40C+

65C+

Description

This fryer can cook up to 85 lbs. of potatoes per hour.

This fryer can cook up to 63 lbs. of potatoes per hour.

This fryer can cook up to 72 lbs. of potatoes per hour.

This fryer can cook up to 120 lbs. of potatoes per

hour.

Features

Frying Area: 14" x 14"

Oil Capacity: 42 lbs.

BTU Input: 122,000

Frying Area: 14" x 14"

Oil Capacity: 35 lbs.

BTU Input: 90,000

Frying Area: 14" x 14"

Oil Capacity: 45 lbs.

BTU Input: 105,000

1.2 CHECKING YOUR NEW FRYER

Your new fryer has been carefully packed into one crate. Every effort has been made to ensure

that your fryer is delivered to you in perfect condition. As you unpack your new fryer, inspect

each of the pieces for damage. If something is damaged, DO NOT sign the bill of lading.

Contact the shipper immediately, the shipper is only responsible for 15 days after delivery.

Check the packing list enclosed with your fryer to ensure that you have received all of the parts

to the fryer. If you are missing any parts, contact the dealer from whom the fryer was purchased.

As you unpack the fryer and it's accessories be careful to keep the weight of the fryer evenly

distributed.

CAUTION

To prevent equipment damage, don't tilt the fryer

onto any two of it's casters or pull the unit by the flue

vents.

ENGLISH

Frying Area: 18" x 18"

Oil Capacity: 65 lbs.

BTU Input: 150,000

1-2

Locate your Pitco Frialator warranty and fill in the serial number of the fryer and the date

received. You will find the serial number on the plate inside the door. Put your warranty card

in a safe place for future reference. DO NOT return the card to Pitco Frialator.

1.2.1 Check Your Order

The crate containing the fryer unit will also contain the following:

(2) Pitco Cleaner Sample

(1) Drain Clean Out Rod

1.3 ASSEMBLY AND LEVELING

When you receive your fryer, it is completely assembled with the possible exception of the legs (or

casters) and the heat shield. In some cases, if you have purchased a multi-fryer unit, you may need to

assemble the system.

1.3.1 Leg/Caster Installation and Adjustment

Installing the legs and leveling the fryer is done with a 7/16" wrench, socket, and a large pair of water

pump pliers. The legs/casters must be installed to provide the necessary height to meet sanitation

requirements and assure adequate air supply to the burner. Attach the legs by performing the following

procedure.

a. Lay the fryer on its side being careful not to damage the flue

by pulling on it. Protect the outside of the fryer with

cardboard or a drop cloth when laying it down.

b. Attach each leg/caster with the hex head cap screws sup-

plied with the fryer. Each leg/caster requires four 1/4-20 x

5/8" cap screws.

c. Mount the screws from the inside of the fryer with the nut

on the outside. The nuts have lock washers attached to

them, therefore it is not necessary to use lock washers.

d. When all four legs/casters are mounted, stand the unit up

being careful not to put too much weight on any one leg/

caster. Adjust the height and level the fryer by adjusting the

leveling devices on the leg/caster with the water pump

pliers.

e. On units with casters, move the fryer to the desired location

and lock the wheels using the locking devices on the

sides of the casters.

Adjust Here

Lock

Adjust

Here

Un Lock

1-3

1.3.2 Assembling Multi Fryer Systems

If you purchased a multi-fryer unit, it could be shipped in more than one piece. To assemble the unit

follow the instructions below.

a. Unpack the units and move them close together. Remove the front panels and both heat

shields from the fryers.

b. There are five joining strips to be attached to the units to make them into one system. These

strips are attached in the rear, front, upper front, and the forward and rear caster mount. Use

the screws supplied with your system to attach the strips. Secure them tightly to each unit.

c. Replace the heat shield and front panels to complete the system assembly.

1.4 INSTALLATION

Although it is possible for you to install and set up your new fryer, it is STRONGLY recommended

that you have it done by qualified professionals. The professionals that install your new fryer will know

the local building codes and ensure that your installation is safe.

WARNING

The fryer must be properly restrained to prevent movement or tipping. This

restraint must prevent the fryer from movements that would splash hot liquids

on personnel. This restraint may be any means (alcove installation, adequate

ties, or battery installation).

1.4.1 Installation Clearances

The fryer needs clearance around it for proper operation. Adequate clearances allow for servicing and

proper burner operation. The clearances shown below are for cooker installation in combustible and

non-combustible construction.

Combustible Non-Combustible

Construction Construction

Back 6" 0"

Sides 6" 0"

Floor - Combustible 6" 6"

1.4.2 Gas Connection

Your fryer will give you peak performance when the gas supply line is of sufficient size to provide the

correct gas flow. The gas line must be installed to meet the local building codes or National

ENGLISH

1-4

Fuel Gas Code (NFPA 54-Latest Edition) and ANSI Z223.1-Latest Edition Latest Edition. In

Canada, install the fryer in accordance with CAN/CGA-B149.1 or .2 and local codes. Gas line

sizing requirements can be determined by your local gas company by referring to National Fuel

Gas Code, Appendix C, Table C-4 (natural gas) and Table C-16 (propane). The gas line needs

to be large enough to supply the necessary amount of fuel to all appliances without losing

pressure to any appliance. Other factors that are used to determine the piping requirements

are BTU requirements of the appliances being connected and the length of pipe between the

meter (main shut off) and the appliances.

WARNING

NEVER supply the fryer with a gas that is not indicated on the data plate. Using

the incorrect gas type will cause improper operation. If you need to convert the

fryer to another type of fuel, contact your dealer.

1.4.2.1 Fuel Types - Each fryer is equipped to work with one type of fuel. The type of fuel with

which the appliance is intended to operate is stamped on the data plate attached to the inside of the door.

WARNING

DO NOT use an open flame to check for gas leaks!

1.4.2.2 Gas Line Connection - Connect the fryer to the gas supply line with a connector that

complies with the Standard for Connectors for Movable Gas Appliances (ANSI Z21.69-Latest

Edition). If you are installing a fryer with casters use a quick disconnect refer to the Quick Disconnect

installation instruction, 1.4.2.3. Connect the gas line to the fryer using a pipe joint sealant that is resistant

to liquefied petroleum. If the fryer was disconnected during the fuel line testing, use a solution of soap

and water to leak test the new connection.

NOTICE

NEVER use an adaptor to make a smaller gas supply line fit the cooker

connection. This may not allow proper gas flow for optimum burner operation,

resulting in poor cooker performance.

1.4.2.3 Quick Disconnect Gas Connection - Gas fryers equipped with casters must be installed

with connectors that comply with the Standard for Connectors for Movable Gas Appliances, ANSI

Z21.69-Latest Edition, and Addenda Z21.69A-Latest Edition. This connection should include a

quick disconnect device that complies with the Standard for Quick Disconnect Devices for Use

With Gas Fuel , ANSI Z21.41-Latest Edition. When installing a quick disconnect you must also

install a means for limiting the movement of the fryer. This device will prevent the gas line or the

quick disconnect from being strained. The restraining device should be attached to the cooker on

the back panel as shown in the illustration. The quick disconnect, hose, and restraining device can

be obtained from your dealer.

1-5

1.4.2.4 Fuel Supply Line Leak and Pressure Testing - The fuel supply system must be tested before

the fryer is used. If the fuel line is going to be tested at a pressure greater than (>)1/2 PSIG (3.45 kPa),

make sure that the fryer is disconnected from the fuel line. If the fuel line is to be tested at a pressure

equal to or less than (<) 1/2 PSIG (3.45 kPa), the fryer can be connected but the unit's gas valve must

be shut. Test all gas line connections for leaks with a solution of soap and water when pressure is

applied.

1.4.3 Ventilation and Fire Safety Systems

Your new fryer must have proper ventilation to function safely and properly. Exhaust gas temperatures

can reach as high as 1200°F. Therefore, it is very important to install a fire safety system. Your

ventilation system should be designed to allow for easy cleaning. Frequent cleaning of the ventilation

system and the fryer will reduce the chances of fire. Table 1-2 provides a list of reference documents

that provide guidance on ventilation and fire safety systems. This table is not necessarily complete.

Additional information can be obtained from the American Gas Association, 8501 East Pleasant Valley

Road, Cleveland, OH 44131.

Excessive ventilation causes drafts, which will interfere with the proper operation of the pilot and

the burner. Leave at least 18 inches of open space between the fryer's flue vent opening and the

intake of the exhaust hood.

CAUTION

Ensure that your ventilation system does not cause a down draft at the fryer's

flue opening. Down drafts will not allow the fryer to exhaust properly and will

cause overheating which may cause permanent damage. Damage caused by

down drafts will not be covered under equipment warranty. NEVER allow

anything to obstruct the flow of combustibles or ventilation exiting from the

fryer flue. DO NOT put anything on top of the flue area.

NOTICE

NEVER connect the blower directly to the flue openings. The direct flow of

air will cause poor temperature recovery, poor ignition, inefficient operation of

the fryer, and could extinguish the pilot.

1.5 INITIAL ADJUSTMENTS

After your fryer has been installed as described in section 1.4, it needs to be adjusted to ensure that it

will perform as designed. These adjustments must be performed by a qualified person. To perform

these adjustment the following tools will be needed:

• Manometer (low pressure gauge) • Digital Thermometer (Temperature probe)

• DC Millivolt Meter

ENGLISH

1-6

1.5.1 Visual Checks

After the fryer is in its permanent location, lock the casters and check for levelness. Any additional

leveling that is necessary can be performed as described in section 1.3.

1.5.2 Burner Ignition Systems

CAUTION

Before going any further, fill the fryer with WATER. Water is used for the

installation adjustments because the temperature will never exceed 212°F

(100°C) thereby allowing plenty of adjustment time. Never let the water level

go below the MIN LEVEL mark on the rear of the tank.

WARNING

There is an open flame inside the fryer. The unit may get hot enough to set near

by materials on fire. Keep the area around the fryer free from combus-

Topic

Grease Extractor

Ventilation Hood

Type of Fire Extinguishers

and Detection Equipment

Dry Chemical

Water

Foam

Sprinklers

Smoke Detectors

Fire Detection Thermostats

National Fuel Gas Code

Document

ANSI/NFPA 96-Latest Edition

ANSI/NFPA 12-Latest Edition

ANSI/NFPA 17-Latest Edition

ANSI/NFPA 13-Latest Edition

ANSI/NFPA 11-Latest Edition

ANSI/NFPA 13-Latest Edition

ANSI/FPA 72B-Latest Edition

Underwriters Laboratory

Document

ANSI/UL 710-Latest Edition

ANSI/UL 705-Latest Edition

ANSI/UL 154-Latest Edition

ANSI/UL 299-Latest Edition

ANSI/UL 626-Latest Edition

ANSI/UL 199-Latest Edition

ANSI/UL 268-Latest Edition

ANSI/UL 521-Latest Edition

Table 1-2. Ventilation and Fire Safety References

1-7

tibles.

To light the pilot light, refer to these instructions.

WARNING

Wait 5 minutes before attempting to relight the pilot to allow for any gas in the

fryer to dissipate.

a. Open the gas supply valves to the fryer.

b. Open the fryer's door to gain access to the controls. Turn the thermostat control knob

counterclockwise to the OFF position.

c. Turn the Unitrol valve knob to the PILOT position and push in on the

knob. Hold the knob in for approximately one minute to purge the air

out of the line. Hold a flame to the pilot light until the pilot ignites. This

may take a little while the first time you light the fryer because of air

in the lines. Once lit, hold the knob in for approximately 60 seconds

and then release.

d. If the pilot goes out wait 5 minutes and repeat step c. If after three

tries the pilot will not remain lit, refer to the operator troubleshoot-

ing section of this manual.

e. Turn the Unitrol valve knob counterclockwise to the ON position.

f. Set the thermostat control knob to the desired temperature set-

ting.

g. The main burner will light and be controlled by the thermostat.

h. To completely shut down the fryer, turn the Unitrol valve knob to pilot, push in and

continue turning to OFF.

1.5.2.1 Pilot Flame Adjustment - The pilot flame should be adjusted to produce the proper millivolt

output from the pilot sensing device. Millivolt output for the thermopile should be between 300 and

500 millivolts. This procedure is only necessary on the manual pilot ignition system. Figure 1-1 shows

the pilot assembly with examples of the incorrect and correct pilot size. Example A illustrates a pilot

flame size that is too small to produce sufficient millivolt output. Example B is the correct size for proper

millivolt output.

a. This test requires a DC millivolt meter set to a scale of 0-1000mv.

ENGLISH

1-8

b. Locate the thermopile wires coming from the thermostat/High Limit box going to the

gas shut off valve. The wire insulation size decreases near the gas valve connec-

tions.

c. Connect the negative (-) test probe to pilot bracket.

d. Connect the positive (+) test probe to to one of the High Limit terminal connections

e. Remove the pilot flame adjustment cover.

f. Turning the flame adjusting screw clockwise lowers the flame and the millivolt output.

Turning the screw counterclockwise increases flame size and millivolt output.

g. Rotate the screw in the direction to achieve a reading of 400 ±50 mv for thermopiles.

NOTICE

Allow 3 to 5 minutes between flame adjustments to allow the reading to settle.

h. Replace the pilot flame adjusting screw cover.

1.5.3 Main Burner System

For the burners to work, the gas supply valve must be open. The main burner receives gas from the

main gas supply through the thermostatically controlled valve. When the thermostat is turned up the

gas control valve opens. The pilot ignites the burners. The burner flame should be adjusted at the air

collar (at the bottom of the burner) so the the flame are a soft blue color without lifting off the face of

the burner.

1.5.3.1 Gas Line Requirements - A properly installed gas supply system will deliver 7.0 ±2.0" w.c.

Figure 1-1 Pilot Assembly, Flame Adjustment

1-9

natural gas (12.0 ±2.0" w.c. LP) to all appliances connected to the line, operating at full

demand.

1.5.3.2 Burner Adjustment - The burners must be adjusted to deliver optimum flame. Adjust the

burner flame using the following procedure.

a. Ensure that the Unitrol valve knob is in the OFF position. Remove the manifold pressure

tap plug and connect an accurate pressure gauge (range of 0-16" w.c. in 0.1" increments)

or manometer.

b. Light the pilot burner (see 1.5.2) for the unit being tested and adjust the thermostat to light

the main burners.

c. The installed pressure gauge reading should be the same, ±0.1", as that marked on the data

plate inside the door. If the pressure is correct go to step e, if not, adjust the pressure.

d. To adjust the pressure, remove the regulator adjustment screw cover (see Figure 1-3). Use

a flat tip screwdriver to adjust the screw until the proper pressure is reached. Turning the

screw clockwise will increase the pressure, counterclockwise will decrease the pressure.

e. When the pressure is correct, install the regulator adjustment screw cover.

f. To remove the pressure gauge, turn gas control valve to OFF. Remove the gauge and install

the pressure tap plug.

g. Now that the pressure is set for proper operation, set the main burner flame. Unlock the air

collars by loosening the set screw for the collars. See Figure 5. Turn the Unitrol valve knob

to ON and turn thermostat to light the main burners.

h. Adjust the shape and size by raising or lowering the air collars to achieve a soft blue flame

with well defined inner cones.

i. When the flames have been properly adjusted, lock the collars in place with the set screw

provided.

Figure 1-2 Gas Valve

Showing Location of the

Pressure Regulator and

Pilot Adjusters

ENGLISH

1-10

1.5.4 Initial Cleaning

When the fryer is shipped, many of its parts are covered with a thin coat of oil for protection.

Before the fryer is ready for cooking it must be cleaned. This will remove the oil coating and

any foreign matter that may have accumulated during storage and shipment. Perform the

cleaning as described below.

a . Fill the tank with water and add one packet of Pitco fryer cleaner or a mild detergent.

b. Turn the fryer on and set the thermostat to 200°F. Allow the fryer to heat for 15 minutes.

NOTICE

Do not leave the fryer unattended during cleaning. Never let the water level go

below the "Min Level" mark on the back of the tank.

c. Using the fryer cleaning brush, scrub the inside of the fryer to remove protective coating.

d. When cleaning is complete, turn off the fryer main burners and turn the Unitrol valve knob

to the PILOT position. Drain the water into a container suitable for hot water and dispose

of it.

e. When the tank has cooled, rinse it thoroughly with cool water. Continue to rinse the tank

until the cleaner has been rinsed, thoroughly from the tank.

f. Using a clean dry cloth, wipe out all of the water. Be very thorough removing the water,

because any residual water will cause hot oil to splatter out of the fryer.

CAUTION

Mild steel tanks must be wiped down/coated with oil to keep the tank from

rusting.

g. Now that the tank is clean, you are ready to fill and operate the fryer. Refer to 2.1 for

instructions on adding shortening to the fryer.

1.5.5 Thermostat Calibration Check

NOTICE

Thermostat calibration requires that the temperature of the fryer be raised above

boiling. Therefore, you will need to drain the water from the fryer and fill it with

oil. Before removing the water, perform the initial cleaning of the fryer.

Cleaning the fryer now will prevent you from having to drain the oil and refill

1-11

with water later.

Filling the fryer with oil is described in 2.1. To perform the calibration check detailed below you will

need a digital thermometer.

a. Place the tip of the thermometer in the shortening approximately 1" above the temperature

sensors.

b. Set the thermostat at 325°F and wait for the temperature reading on the thermometer to rise.

As the temperature rises toward 325°F watch the thermometer closely.

c. If the shortening temperature reaches 350°F and the burners DO NOT turn off, turn the

thermostat down. Keep lowering the thermostat setting until the burners go out.

CAUTION

If the burners do not turn off at the lowest thermostat setting, the thermostat

could be defective. Contact your representative immediately.

d. Let the fryer cycle 4 to 6 times before checking the temperature. Compare the thermometer

temperature against the thermostat setting. If the values are more than 5°F apart, calibrate

the thermostat using the appropriate calibration procedure in this manual.

1.5.6 Thermostat Calibration

a. Place the tip of the thermometer in the shortening approximately 1" above the temperature

sensors.

b. Set the Thermostat to 325°F and wait for the temperature reading on the thermometer to rise.

c. Let the fryer cycle 4 to 6 times to ensure that the temperature has stabilized. Compare the

thermometer temperature against the thermostat setting. If the values are more than 5°F

apart, calibrate the thermostat using the appropriate calibration procedure.

ENGLISH

1-2

snoitcurtsnI gnitarepO :2 retpahC

siht ni dedulcnI .ecnamrofrep tseb eht niatbo ot reyrf ruoy etarepo ot woh sebircsed retpahc sihT

.sreyrf sag rof snoitcurtsni gninaelc dna ,gnitarepo ,gnillif era retpahc

1.2 REYRF EHT GNILLIF

dilos tlem oT .derreferp si diuqil tub ,reyrf eht ni desu eb nac gninetrohs dilos dna diuqil htoB

.2.2.2 noitces ni noitcurtsni eht wollof ylluferac ,gninetrohs

1.1.2 gninetrohS diuqiL htiW reyrF eht gnilliF

.a .desolc yletelpmoc si evlav niard eht erus ekaM

.b dekram enil "leveL liO" eht ot lio htiw reyrf eht lliF

.knat eht fo kcab eht no

2.1.2 gninetrohS diloS htiW reyrF eht gnilliF

GNINRAW

renrub eht fo pot no gninetrohs dilos fo skcolb tlem reveN

.ytnarraw ruoy diov lliw dna erif a esuac lliw sihT .sebut

.a .desolc yletelpmoc si evlav niard eht erus ekaM

.b .sebut eht gnirevoc neercs eht evomeR

.c ."1 naht regral on sebuc otni gninetrohs eht tuC

,neewteb ,woleb gninetrohs eht kcap SYAWLA

yna evael TON OD .sebut renrub eht fo pot no dna

dilos eht gnikcap nehw erac esU .spag ria egral

eht kaerb ro dneb TON OD .knat eht ni gninetrohs

degamad era eseht fI .seborp rosnes erutarepmet

.ylreporp noitcnuf ton lliw reyrf eht

.d -trohs eht ,gninetrohs htiw dekcap si reyrf eht ecnO

refer ,gninetrohs eht tlem oT .detlem eb tsum gnine

diloS gnitleM dna ,1.2.2 noitces ,pU-tratS reyrF ot

.2.2.2 noitces ,gninetrohS

HSILGNE

2-2

2.2 SNOITCURTSNI GNITAREPO

doof eht rof snoitcurtsni noitaraperp eht wollof ,tseb yrev eht tuo semoc syawla doof eht erusne oT

tsal lliw gninetrohs tseb ehT .sdoof deirf tseb eht sekam gninetrohs tseb eht gnisU .gnikooc era uoy

eb dluohs gninetrohs eht esu ni ton nehW .yenom uoy evas dna gninetrohs edarg rewol naht regnol

.noitanimatnoc tneverp ot derevoc dna delooc

NOITUAC

latnedicca tneverp ot secived gniniartser gnisu dellatsni neeb sah reyrf ehT

diuqil toh sah ti nehw reyrf eht evom ot tpmetta ton oD .tnemevom ro gnippit

.snrub ereves esuac nac sdiuqil toh gnihsalpS .ti ni

GNINRAW

.gninetrohs toh morf yawa sdiuqil peeK .xim TON OD gninetrohs dna retaW

.gniliob tneloiv esuac lliw gninetrohs toh eht otni doof nezorf diuqil gnipporD

1.2.2 pU-tratS reyrF

!LIO HTIW GNILLIF TUOHTIW REYRF TRATS TON OD

.a .2.5.1 noitces ni debircsed sa thgil tolip eht thgiL

.b sihT .gnittes erutarepmet derised eht ot )tatsomreht( bonk lortnoc erutarepmet eht nruT

.lenap lortnoc tnorf eht no ro srood tnorf eht dniheb detacol si bonk

.c .thgil lliw srenrub niam ehT

2.2.2 gninetrohS diloS gnitleM

ECITON

ylluferac hctaW .reyrf eht fo gnilcyc seriuqer woleb erudecorp gnitlem ehT

,siht tneverp oT .gnihcrocs si gninetrohs eht ,deciton si ekoms fI .ekoms rof

.no srenrub eht evael uoy emit eht esaerced

.a .noitisop NO ni evlav lortinU eht ecalP

.b .F°051 ot tatsomreht teS

.c .sdnoces )4( ruof yletamixorppa rof erif ot srenrub niam wollA

.d .tuo og srenrub niam litnu nwod tatsomreht nruT

3-2

.e .sdnoces 03 tiaW

.f .detlem si gninetrohs eht litnu .e hguorht .c spets taepeR

.g yltnatsnoc no niamer lliw srenrub ehT .erutarepmet gnitarepo lamron ot tatsomreht teS

.gnittes tatsomreht eht sehcaer erutarepmet gninetrohs eht litnu

.h .esu ot ydaer dna yllamron gnitarepo won si reyrf eht ,erutarepmet ta ecnO

3.2.2 nwoD-tuhS reyrF

edom ybdnats ehT .ETELPMOC dna YBDNATS ,noitarepo reyrf fo sedom nwodtuhs owt era erehT

ylppus sag eht ffo snrut nwodtuhs etelpmoC .elcyc ot srenrub niam s'reyrf eht rof ytiliba eht sevomer

:yb reyrf eht nwod tuhS .reyrf eht ot

YBDNATS eht ot esiwkcolc evlav sag eht nruT .FFO ot tatsomreht eht nruT

siht niamer nac dna ybdnatS ni won si rekooc ehT .noitisop TOLIP

ni rekooc eht evael REVEN .emit fo sdoirep feirb ylno rof yaw

.thginrevo ybdnats

ETELPMOC evlav sag eht nrut dna hsup ,rekooc eht nwod tuhs yletelpmoc oT

yletelpmoc won si reyrf ehT .noitisop FFO eht ot esiwkcolcretnuoc

.deretlif dna denaelc eb nac dna nwod tuhs

3.2 GNINAELC YLIAD

eht mrofreP .ecnaraeppa dna ecnamrofrep kaep niatniam ot yad yreve denaelc eb dluohs reyrf ruoY

.yad yreve woleb serudecorp

.a htiw enod eb dluohs sihT .reyrf eht fo roiretxe eht otno sllips taht gninetrohs yna pu epiW

.mraw llits si lio eht elihw htolc tfos naelc a

.b ni retaw teg ot ton luferac eB .secafrus naelc ot tnegreted dlim a htiw retaw mraw esU

.knat yrf eht morf tnegreted yna evomer ot dna gninetrohs eht

.c .yrassecen fi sniats naelc ot dap ro redwop gniruocs evisarba-non a esU

.d .2.3 noitces ni debircsed reyrf ruoy fo gninaelc tuo liob ylkeew eht mrofreP

HSILGNE

La page charge ...

Pitco 45C+, 122K BTU Manuel utilisateur

Marque: Pitco

Modèle: 45C+, 122K BTU

Catégorie: Friteuses

Taper: Manuel utilisateur

Ce manuel convient également à

35C+, 90K BTU

Télécharger le PDF

rapport

dans d''autres langues

English: Pitco 45C+, 122K BTU User manual

Pitco 45C+, 122K BTU Manuel utilisateur

Ce manuel convient également à

Pitco 45C+, 122K BTU Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents