Binatone SYMPHONY 2200 Manuel utilisateur

Marque: Binatone

Modèle: SYMPHONY 2200

Catégorie: Téléphones

Taper: Manuel utilisateur

Important note — emergency calls

The Symphony 2200is not designed for making emergency calls when

access to Emergency Services.

(This means that you should also have a basic phone that does not

need mains power, connected to your line so that you can make calls

during a power failure.)

USER GUIDE

If you need help …

The is available

from 9.00 am to 5.00 pm, Monday

to Friday, on

Calls are charged at Local Call rate.

Binatone Help Line

0845 345 9677

Unpacking your Symphony 2200

In the box are:

the cordless handset (two handsets with

a Twin system, three with a Triple

system, four with a Quad system)

the base unit

rechargeable batteries or a battery pack,

and a battery compartment cover for

the handset

a telephone line cable

a mains power lead and adapter

If you have an Symphony 2200Twin, Triple

one, two or three charger pods

a mains power lead and adapter for

each one

Keep the packaging materials in a safe

place in case you later need to transport

the unit.

Keep your sales (till) receipt, which is

your guarantee.

Stylish Digital Cordless Telephone

11 Handset registration

14 Troubleshooting

15 Guarantee and service

16 Technical details

Interference

If the sound quality gets worse as you move around while on a call, this is

probably due to interference between the handset and the base unit, perhaps

because you are too near to another phone or other electrical equipment. Move

to a different position to clear the interference. If you do not move, your call

may be cut off.

Radio interference in the environment may occasionally cause a short break in

the link between the handset and the base unit while you are on a call. The

handset’s display will flash briefly, while the unit automatically changes to a

different channel to restore the link.

Keeping the batteries charged

When you don’t need to carry your handsets around (for example, at night),

leave them on the base unit or charger pod, to keep the batteries charged.

Whenever the battery charge level symbol on the display shows ‘nearly empty’,

replace the handset on the base unit or charger pod.

‘Out of range’ warning

If you hear a warning tone during a call, and/or the sound in the earpiece

becomes faint or distorted, you may be going out of range of the base unit.

Move nearer to the base unit within 20 seconds, until the tone stops.

Otherwise, your call may be cut off.

While you are out of range and you are not on a call, the handset’s display

shows and the ‘signal level’ symbol flashes. Before you make a call,

you must move closer to the base unit until the handset’s name and number

are displayed and the symbol stops flashing.

Cleaning and care

■

Don’t clean any part of your Symphony 2200 with benzene, thinner or other solvent

chemicals — this may cause permanent damage which is not covered by the

Guarantee. When necessary, clean it with a damp cloth.

■

Keep your Symphony2200 away from hot, humid conditions or strong sunlight,

and don’t let it get wet.

■

Every effort has been made to ensure high standards of reliability for your

do not try to repair

it yourself — consult your supplier or the Binatone Help Line.

Contents of this User Guide

1 Where to find it

2 Installation

3 Making and answering calls

4 Memory dialling

5 Caller Display

6 Tones and volumes

7 Call barring

8 Customising your phone

9 Resetting the system

10 Using a muti-handset system

11 handset registration

Baby Call

Operational notes

Troubleshooting

15 Guarantee and service

16 Technical details

Pressing buttons on your phone

■

When the instructions in this user guide tell you

simply to ‘press’ a button, this means that you

should press the button briefly, then release it.

■

When the instructions tell you to ‘press and hold’

a button, this means you should keep the button

pressed until the display changes and/or you hear a

tone.

Waste electrical products must not be disposed of with

household waste. This equipment should be taken to your

local recycling centre for safe treatment.

Ver , Jul. 07

The outside call is put on hold. When the user of the other handset unit

answers, you can talk on an intercom call.

Press the HANG UP/C to transfer the call

If the handset user does not answer:

you can get back to the outside call by pressing the INTERCOM button again

You can also shuttle backwards and forwards between the calls -

To shuttle between two calls

When you have both an outside call and an intercom call in progress, you can

shuttle from one to the other, like this:

◗

Press the INTERCOM for one second to speak to each in turn, putting

the other on hold

You can transfer the outside call to the other handset by pressing the

HANG UP/C

while you’re connected to the intercom call

If you press theHANG UP/C while you're connected to the outside call,

you will disconnect it.

You can set up a conference using two handsets.

When you have an outside call (either one you've made or answered, or one

that’s been transferred to you) in progress

Press the INTERCOM then key in a handset number

The outside call is put on hold. When the other handset user answers,

and you have an intercom call in progress:

Press and hold the (STAR) button for 2 seconds to set up a

three-way conference

Both you and the other user are connected to the outside call.

If you press HANG UP/C during the conference call, youll leave the other user

connected to the outside call.

If the other user presses HANG UP/C, you’ll be left connected to the outside call.

New call

tone

When both handsets are on an intercom call and an outside call comes in, you will

hear NEW CALL TONE over your conversation to tell you that someone is calling you.

Press the

To answer the outside call and put the intercom call on hold (so you can later

use shuttle,conference or transfer):

Press

INTERCOM

To answer the outside call and end the intercom call:

To set up a three-way conference

To suspend the other handset user from the conference call: Press and hold

the (STAR) button for 2 seconds

You remain connected to the outside call.If the other user has not hung up,

you can bring her/him back into the conference by pressing and hold the

(STAR) button for 2 seconds.

The handsets supplied with your Symphony2200 system are already

registered to the base unit. You don t need to register them yourself.

If you buy new handsets separately, you’ll need to register them. Up to

six handsets can be registered to each base unit; and each handset can be

registered to up to four base units.

To register a new handset

Press and hold the HANDSET LOCATOR

on the base unit until you

hear Registration tone (repeated ‘beeps’)

On the handset, press the

then the

▲

▼

button to display

Press the PHONE/OK

The display shows BS 1234 . If any of these numbers is steady (not

flashing), then the handset is already registered to that base unit.

Press 1 to select base unit number 1

The display shows PIN____

Key in the system PIN (default 0000) and press the PHONE/OK

The display shows WAIT____ for a few moments, while the handset

searches for a base. Then it shows a list of handset numbers which are still

free on the base unit.

(For example, 1346indicates that numbers 1,3, 4 and 6 are free; 2 and 5

are already assigned to other handsets.)

BASE

Key in a free handset number

After a moment, the display should show the handsets name and number.

If registration

fails…

Try again, making sure you begin step 2 as soon as Registration tone starts.

To register to a new base unit

If your handset is already registered to a base unit, and you want to register it to

another one:

◗

Follow steps 1 to 5 on page 20. But at step 4, select the lowest numbered

free base unit (the lowest number that is still flashing).

To select a

base unit

If your handset is registered to more than one base unit, you can select which

one you want it to operate with. Or you can leave it to search and establish a

link with the nearest free base unit.

Press the

▲

▼

button to display SELBASE

Press the PHONE/OK

The display shows a list of the base units to which the handset is registered.

The currently selected base unit is steady; others are flashing.

Key in a base unit number (or 0 to let the handset search for the nearest

free base

unit) and press the PHONE/OK to confirm

The display goes back to SELBASE and you can wait a moment or press

HANG UP/C to go back.

To de-register

a handset

Press the

▲

▼

button to select

Press the PHONE/OK

The display shows the numbers of all handset registered to

the base unit.

Key in a the number of the handset to be de-registered.

The display goes back to and you can wait a moment

or press HANG UP/C to go back to standby mode.

The Symphony2200 must be serviced by trained engineers. NEVER attempt

any repairs or adjustments yourself you could make the problem

worse and invalidate the Guarantee.

If you have problems using your Symphony2200 cordless phone,

refer to the separate user guide.

ALWAYS check

first that:

■

you have followed all the steps listed in section 2

to install and set up your Symphony2200

■

all connectors are firmly inserted in their sockets

■

mains power to the base unit telephone is switched

on at the socket

“I can’t make or

answer calls.”

If you don’t hear Dial tone when you press the

handset’s PHONE button, check whether the base unit

or another handset is already using the line.

If you’re using a cordless handset, make sure it’s within

range of the base unit. Move closer to the base unit

and see if that helps.

Make sure you’re using the telephone line cable that

was supplied with your Symphony2200. Other telephone

line cables might not work.

If the handset’s display is blank, press the HANG UP/C

button to switch it on.

Call barring may be set (see section 7) for your handset.

Check with any other user who may have set it.

Switch off power at the mains socket, wait for a few

seconds and then switch back on. This may solve the

problem.

“The phone is

not ringing.”

The ringer melody may be set to OFF. Change it as

described in section 6.

Check that the total REN value of all instruments con-

nected to the line is no more than 4 . Disconnect

one or more instruments and see if that helps.

“Caller Display

isn’t working.”

You need to subscribe to the Caller Display feature

from your network service provider. You should find

contact details on your phone bill.

The caller may have withheld their number by dialling

141. Or they may be calling from a network that does

not transmit the caller’s number (for example, it may be

an international call).

When you store local numbers in the Phone Book,

include the full dialling code (you’ll still be charged

local rate for making calls). Then the name will be

shown as part of the Caller Display record. Alternatively,

you can set the national dialling code for your area as a

local code.

“The phone is

dialling very

slowly”

The dial mode may have been accidentally changed

. Change the setting to —

you should hear ‘beep’ tones as you dial.

“I can’t make

intercom calls.”

Make sure you’re using the correct handset number

Make sure the handset you’re trying to call is switched

on and within range.

“Baby Call isn’t

working.”

When you turn Baby Call on, you also need to set the

number to be dialled.

PBX use

“Last Number

Redial and/or

memory dialling

don’t work on

a PBX.”

When you first make a call, press the REDIAL/CDS/P

button for a pause between the outside line access

code (for example, 9) and the telephone number. You

should later be able to redial the number.

When storing numbers in memory, you can include the

outside line access code (e.g. 9) with each number.

If your PBX requires you to wait for a second Dial tone

before dialling the telephone number, press P for a

pause between the access code and the number.

If the fault persists …

Disconnect all other instruments connected to the

same line as the Symphony2200 and see whether you

Disconnect the base unit from the telephone line and

plug a different phone into the master telephone

socket. Try making a call. If this works, the line is OK.

If the call does not work, and you are using a two-way

socket adapter, remove it and plug a telephone

directly into the socket. If the call now works, the

adapter may be faulty.

If you cannot make a call, the fault may be on the

exchange line. Contact the service provider (the BT

engineers on 151, or your cable company).

If you still cannot identify the cause of the problem,

contact the Binatone Help Line on 0845 345 9677.

The Binatone Symphony 2200 is guaranteed for 12 months from the date of

purchase shown on your sales receipt. The Guarantee does not cover damage

telephone line, or lightning.

Please keep your sales (till) receipt — this is your guarantee.

You should also keep the original packaging material.

In the unlikely event that you need to return your Symphony2200 to our Repair

Centre while it is under

guarantee, there will be a £5 handling charge.

While the unit is under Guarantee

Disconnect the base unit and charger pod from the telephone line and the

mains electricity supply

Pack up all parts of your Symphony2200, using the original packaging.

Remember to include the mains adapters

Return the unit to the shop where you bought it, making sure you take your

sales receipt

After the Guarantee has expired

If the unit is no longer under Guarantee, first follow steps 1 and 2 as for repair

under Guarantee. Then …

Call our Service Department on 0845 345 9677 and ask for a quotation of the

repair charge and details of where to send your Symphony2200 for repair

Make sure you include with your Symphony2200:

■

your name and address

■

a cheque or postal order for the value of the repair charge

Return your Symphony2200 to the address given by the Service Department

This does not affect your statutory rights.

Standard

Digital Enhanced Cordless

Telecommunications (DECT)

Frequency range

1.88 to 1.9 GHz (bandwidth = 20 MHz)

Channel bandwidth 1.728 MHz

Operating range

up to 300 m outdoors; up to 50 m indoors

Operating time

for cordless

handset

standby: 100 hours approx.

talking: 10 hours approx.

battery charge time: 15 hours

Temperature

range

Operating 0 ºC to 40 ºC

Storage -20 ºC to 60 ºC

Electrical power

Cordless handset

— three AAA-size 550 mAH NiMH

rechargeable batteries

Port specification The port (connected to the mains power supply) is a

SELV port with respect to EN41003.

The port (connected to the telephone line) is a TNV port with respect to

EN41003.

PBX compatibility Timed break recall: programmable as 85 ms (Short) , 100 ms

Pause length: 3 seconds. Signalling type: DTMF (dual-tone multifrequency), also

called tone dialling; or loop-disconnect (pulse dialling).

Network connection

This equipment is intended to be used in the UK only. Operation on other

countries’ PSTN termination points cannot be guaranteed.

Charger pod

— input 230 V AC, 50 Hz; output DC 9 V, 300 mA

Declaration of conformity

The Binatone Symphony2200 complies with the essential

protective requirements and objectives of:

■

EC R&TTE Directive 1999/5/EC

■

EC Directive 2006/95/EC

■

EC EMC Directive 89/336/EEC

and conforms to the following relevant harmonised

■

Radio: EN 301406 : V 1.5.1:2003

■

EMC: EN 301489-1 : V 1.6.1:2005

12 Baby Call

With Baby Call (babysitter’s call) turned on, the handset will automatically dial a

specified number when any button (except PROG) is pressed. Before you turn

Baby Call on, you must programme the Baby Call phone number to be dialled.

With Baby Call turned on, the handset can’t be used for calling Emergency

Services. Make sure there’s another handset (or phone) available for

emergencies.

Press the button then

Press

Key in the phone number and press to confirm

If a Baby Call number is already programmed use to delete

Press

to go to

Press to select Tick (ON) or Cross (OFF)

Press and hold to go back Stand by mode

When Baby Call is turned on, the number is shown on the display, with a ¡®lock¡¯

symbol on the top line.

To turn Baby Call off:

Press the

▲

▼

button to display

BABYCALL

Press the PHONE/OK

Press the PHONE/OK to display a

cross next to ON / OFF

Make sure the symbol disappears from the display.

rANGE OUT

button then

Press

standards:

ON / OFF

13 Operational notes

Electrical safety

■

DON’T let the base unit get wet. Electrical equipment can cause serious

injury if used while you are wet or standing in water.

■

If the base unit ever falls into water, DON’T retrieve it until you have

unplugged the power lead from the mains and the telephone line plug from

the telephone socket; then pull it out by the unplugged cables.

■

NEVER use your Symphony2200 outdoors during a thunderstorm— unplug the

base unit from the telephone line and the mains socket when there are

storms in your area. Damage caused by lightning is not covered by the

guarantee.

Siting the base unit and charger pod

The base unit and charger pod should each be placed on a level surface, in a

position where:

■

the mains adapter plug will reach an easily accessible 230-V

switched

mains supply socket — never try to lengthen the mains power cable

■

the telephone line cable will reach your telephone line socket or extension

socket (base unit only; charger pods have no connection to the telephone

line)

■

it is not close to another telephone — this can cause radio interference

during calls

■

it is not close to a sink, bath or shower, or anywhere else where it might get

wet

■

it is not close to other electrical equipment — fridges, washing machines,

microwave ovens, TVs, fluorescent lights, etc.

Radio signals between the handset and the base unit

To use your handset and base unit together, you must be able to establish a

radio link between them. Be aware that:

■

Siting the base unit as high as possible will give better results — for example,

in a two-storey house, the best position may be on the first-floor landing.

■

Any large metal object — like a refrigerator, a mirror or a filing cabinet —

between the handset and base unit may block the radio signal.

■

Other solid structures, like walls, may reduce the signal strength.

Symphony 2200

the mains power fails. So you should make alternative arrangements for

or Quad system, you should also have:

Symphony2200. However, if something does go wrong, please

can make a call.

by misuse or negligence, or by excessive voltages — for example, faults on the

utton

BABYCALL

NUMBER

TONE

PULSE

— inp

ut 230 V AC, 50

Hz; output AC

V, 300 mA

ase unit

7.5

(Medium) (recommended for most PBX systems) or 250 ms (Long)

■

Ele

ctrical Safel

y: EN 6095

0-1 : 2001

+ A :2004

EN 301489-6 : V 1.2.1:2002

PHONEBOOK

ringer

Display messages and symbols

Installation

3 Making and answering calls

To make a call

Key in the phone number

If you make a mistake, press

to clear digits from the display.

To clear all digits, press and hold

Press

To answer a call

When the handset and base unit ring:

◗

Press

To end a call

◗

Press

so that the

symbol disappears from the display

Last Number Redial

To make a repeat call to the last number you dialled:

Press

To make a repeat call to one of the 10 last numbers you dialled:

Press

▲

▼

until the number is shown on the display

Press

Muting the mouthpiece

◗

Press and hold key

for 4s

to mute the mouthpiece

While the mouthpiece is muted the person on the other end of the call can’t

hear you. is shown on the display.

◗

Press

and hold key

once again to un-mute the mouthpiece

6 Tones and volumes

To adjust the earpiece volume during a call

Press

▲

▼

to change the volume

Handset ringing melodies

To change the ringing melody for incoming external calls

Press

melod

Press

▲

▼

to hear each melody in turn.

Press

to confirm the melody you want

Press and hold

to go back to standby mode

4 Memory dialling

You can store up to 40 numbers in each handset’s memory. Each number can

have up to 2

digits, and you can store a name of up to 10

characters with

the number.

To store a number

The display shows:

Press

add

Press

name

Key in the name, using the numbered keys

Press

Key in the number

Note:

if you make a mistake , press to clear digits or letters from

the display.

Press

You can now carry on storing numbers

To store a number from redial list

ress then select the number

Press

if you wish.

ress to confirm.

ress key in a name then

To make a memory call

Press

▲

▼

until the display shows the name and

number

Press

to dial the number

Handset ringing volume

You have a choice of

eight

volume levels

including

ringer off.

Press

rvo

off

Press

▲

▼

to change the volume

Press

to confirm

Press and hold

to go back to standby mode

Base unit ringing melody

Press

volume

Press

melody

Press

melody

Press

▲

▼

to hear each melody in turn

Press

to confirm the melody you want

Press and hold

to go back to standby mode

Base unit ringing volume

Press

▲

▼

to change the volume

Press

to confirm the volume level you want

Press and hold

to go back to standby mode

* If you’ve set the ringer volume to OFF, you won’t hear any melody at this point.

Key tone on/off

Each time you press a key, you hear a tone. You can turn this off if you prefer.

Press

then

handset

Press

keytone

Press

off

Press and hold

to go back to standby mode

7 Call barring

Using call barring, you can prevent certain types of call being made on your

handset. There are four levels of Call Barring:

■

no bar

— all calls are allowed. This is the default.

■

local

—

no international calls

■

internal

— you can’t make any outgoing calls except emergency 999 calls.

To bar calls to specified numbers

Press

then

press

base

Press

then press

Press

to select [

] or [

]

the display shows a list of registered handset numbers

Key in a handset number

key in the barred number and confirm using

ress to select [

] and confirm using

Using

to select tick(ON) to activate the call barring or

Cross (OFF) to de- activerte it ,

to go back.

8 Customising your phone

Your handset’s name

The default name shown on your handse

t’s display is

[

]

. You can

change this to anything with up to ten characters.

Press

then

handset

Press

hs name

Press

to display the current name

Press

repeatedly to clear the display

Key in your chosen name

Press

to confirm

Press and hold

to go back to standby mode

Auto-answer

Normally, you need to press

to answer an incoming call. But with

auto-answer turned on, when your handset is resting on the base unit and

it rings for an incoming call, you can answer by simply lifting the handset.

To turn auto-answer on or off:

Press

then

handset

Press

then

auto ans

Press

to select

Tick (ON)

Cross (OFF)

Press

and hold

to go back to standby mode

If you have turned auto-answer on, don’t press the

after

you’ve answered a call by lifting the handset;

Locking the keypad

When the keypad is locked, no numbered keys can be pressed so you can’t make

calls by mistake.

To lock the keypad:

ress and hold for 4

seconds

The display shows the symbol when the keypad is locked.

To unlock the keypad:

ress and hold for 4

seconds again

The symbol will disappear from display.

With the keypad locked, you cannot make emergency calls to 999 or 112.

Your security PIN

You will only need this feature if you plan to set up

Call Barring

The base unit has a default PIN (personal identity number) of 0000

. You can

change it to any number you’ll remember, with up to eight digits.

9 Resetting the system

If you reset the system, all features will return to their default settings.

While you are resetting the system, you should disconnect the telephone

line cord from the back of the base unit, so you won’t be interrupted by

incoming calls.

Reset Base

Press

base

Press

then

default

Press

You hear a confirmation tone

Reset handset

1 Where to find it

Redial / CDS/

PAUSE button

once

twice

Press to open a list

of the last 10 phone

numbers you called.

Press to open the

list of Caller Display

records.

Press while dialling a

number to insert a

pause (you might need

this on a PBX).

Ringer Off /

Scroll button

Press and hold for 4 seconds

to turn the ringer off.

When viewing a number with

more than 12 digits, press to

scroll back along the display.

R (Recall) button

You may need this if your

phone is connected to a

PBX, or if you use

network-based services.

Press to start using Menu

functions.

Press to begin or answer a

phone call.

When using Menu functions,

press to confirm your

selection.

UP and DOWN buttons

Press during programming to

Press to move through the Caller

Press during a call to adjust the

Keypad Lock /MUTE /

Scroll button

Press and hold for a moment to lock and

unlock the

keypad.

Press during a call to mute the mouthpiece.

When viewing a number with more than 12

digits,press to scroll

for ward along the display

PHONE BOOK button

Press to open the Phone Book.

INTERCOM button

Press to make an intercom call

to another handset.

G U

(Cancel) button

Press to end a call.

Press and hold for 3 seconds to

switch the handset on and off.

Press

while editing

using

u f

nct

cancel

what

you’re doing and return the

display to Standby mode.

move through the menus and

options.

Display or Redial list.

volume

the

earpiece

speakerphone.

16:25

When this shows ‘nearly empty’ ( ), put the handset on the

base unit or charger pod as soon as possible, to charge the

batteries. While the batteries are being charged, this blinks.

Appears when you have a connection to the outside line.

Flashes when there’s an incoming call to be answered

(even if the ringer is turned off).

The handset’s number

The current time

The handset’s name

)

Phone

Book

Ringer off

Comes on when you’re storing numbers in the Phone Book, and

when you’re making calls to stored numbers.

Comes on when the handset’s ringer is turned off.

Radio link/

signal level

on steadily when there’s a radio link between

the handset and base unit. lashes while the handset is trying

to establish a link

e first symbol

It f

to the base unit

The second symbol shows the strength of the signal.

If this symbol flashes while

you’re on a call, move closer to the base unit

Battery

charge

level

Phone

New call

You have new Caller Display records.

What the symbols mean

The duration of each call is displayed, from 20 seconds after you press the

PHONE button for a line, until 5 seconds after you end the call.

Lock

Comes on when your handset’s keypad is locked.

Mute

Comes on when your handset’s microphone is muted.

If you use a network voice mail service, this symbol appears

when you have new messages in your Inbox.

Network

voice mail

Plug the mains adapter into a

230 V AC, 50 Hz mains socket,

with the switch on the socket

set to OFF

Plug the mains adapter into a 230 V AC,

50 Hz mains socket, with the switch on

the socket set to OFF

Switch on at the mains socket(s)

Install the charger pod(s) …

Connect the mains power

lead and the telephone

line cord into the

underside of the base unit

Use the telephone line

supplied with your

use any other

telephone line cord

cord

Choose a suitable site for the

base unit telephone

The CHARGE

light comes

The bars on the

battery level symbol

continuously change

as the batteries are

being charged

Make sure the mains socket is

switched on — the phone won’t

work without electrical power

Connect the base unit to the telephone line

Switch off power at the mains socket

Insert the telephone line plug into the socket

Switch mains power back on

NOTE: the charger pod doesn’t have

a connection to the telephone line.

Charge the batteries for 15 hours

Before you use the cordless

handsets for the first time,

it’s important to charge the

batteries fully.

You hear a ‘beep’ when the

handset is correctly in

position on the charging

cradle.

To keep the batteries charged,

whenever you don’t need to use the

handset (such as overnight, or when

you go out), leave it on the base unit

or charger pod.

Leave the handsets on the base unit

and charger pod(s) for 15 hours.

Fit the batteries in the cordless handsets

Insert the three rechargeable

batteries as shown

Drop in the battery compartment

cover, then slide it forward until it

clicks firmly into place

Press

show

first

memory stored

entry

You can edit the number using HANG UP/C before storing it

call bar

To bar certain type of call

Press

hen press

base

Press

then press

Press

then k

ey in a handset number, press

select [

] , [ ] o

r [

]

Using

to confirm or

to go back to turn call barring off

* Follow 1 to

4 above, setting the level to [

] at step

call bar

Clear memories on handset

Press

then

Press

then

Press

to c

nfirm

handset

Press

then

Press

Key in your new PIN and Press

to confirm.

Press

to go back.

base

Press

then

Press

then

default

Press

You hear a confirmation tone from the

handset.

handset

10 Using a muti-handset system

■

page

the handsets from the base unit (this is useful if you can t find a handset)

■

make

intercom

calls from one handset to another

■

transfer

outside calls between handsets

To page all

handsets

Press the

HANDSET LOCATOR

button on the base unit

All registered handsets ring, and their

displays show

PAGING

To stop the ringing:

Press the

HANDSET LOCATOR

button again, or press any button

on any handset

If you have an

multi-handset system, you

already have up to six

handsets registered to your base unit.

You can register additional handsets —

altogether, up

to six handsets per base

unit

. With two or more

handsets registered, you can:

■

Set up a three - way conference call

To make an intercom call

Press the

INTERCOM

button on the handset

EITHER key in a handset number (1 to 6, depending on how many

handsets are registered);

OR key in

to call all registered handsets;

If you called a handset, it rings and its

display shows

INT

and your handset number.

To answer the intercom call

Press the

PHONE/OK

button on the ringing handset;

To end the intercom call

Press the

HANG UP/C

button on the handset;

To transfer

a call

Make or answer an outside call using the handset

Briefly

press the

INTERCOM

button then key in a handset number (or

press

to call all handsets)

To modify (change) a number in memory

Press

show memory stored.

add

Press

▼

TWICE

modify

Press

▲

▼

until the display shows the name

Modify the name if necessar

y, pressing to clear characters from

the display before keying in the correct ones

Press

he display shows the corresponding number

Modify the number if necessa

ry then press

You can now carry on modifying numbers

To return a call

To make a return call to someone who’s called you:

◗

Press

while either the name or number is shown on the display

To delete a Caller Display record

Press

twice

, then

▲

▼

to select the caller display record,

press

Press

twice

delete

Press

to delete this record

or press

if you don¡¯

't want to delete the record

When there are no more records, the display shows

handset name.

To delete all Caller Display records

Press

twice

The display shows the first Caller Display record

press

Press to confirm or press

if you don'¡¥t want to delete all records

When there are no more records, the display shows

handsset name.

5 Caller Display

If you subscribe to this feature from your service provider, you can see the phone

numbers of people calling you, before you answer. The Symphony2200 will store

the

numbers of the last

incoming call

. Each Caller Display record includes:

■

The caller’s

name

, if it’s one you’ve already stored in your phone’s memory.

■

The caller’s

number

(up to 20 digits). The number won’t be displayed if the

network they’re calling from does

’t support this feature

withheld

If the call

’

s number was

’

t available, the display shows

■

The

date and time

of the call

When there have been calls you haven’t answered, the symbol is shown on

the display.

To check Caller Display records

Press

twice

Press

▲

▼

to scroll through the records

You’ll see either

names or number

.If you see a

name

displayed

number

to check Date/Time of the call,

Press

to show the Date/Time,

the

symbol will

disappear

from the display, once you enter the record list.

Press

then

To store a number from Caller Display

Press

twice

, then

select the

number.

Press

ress to confirm.

ress key in a name then

You can edit the number using HANG UP/C before storing it

if you wish.

then

by (Tick)

by(Cross)

UNKNOWN

To delete an entry (all entries) from

redial list

Press

then

select the number.

Press to confirm delete an entry or delete all entries.

To delete an entry or all entries from Phone Book

Press

then

select

or .

then

select the number.

Press to confirm.

volume

COPY tO PB

DELETE

DELETE ALL

DELETE

DELETE ALL

COPY tO PB

volume

off

then key in a handset number

Press

then press

To set the date and time

Press

then

Press

to confirm

DATE/TIME

dd-mm-yy

key in the date

Press

key in the time

HH-MM

If you do will clear all numbers from the handset's phonebook and redial list

Dial mode

Always leave this setting at .

’

s ver

y unlikely that yo

’ll need this function, and it

’

usually best to leave

the setting at its default,

need to change this setting (also

called the

recall lengt

) to

. If

applicable,

consult the PBX documentation for details.

Clear all memories on base

Select this to clear all numbers from caller display list

Press then

The display asks:

Press then

Press to confirm, to cancel

Flash

CONFIRM?

twice

Handset Switch ON/OFF

Press

and hold

The handset will switch ON or OFF

for 3 seconds

base

then

CONFIRM?

CLEAR MEM

PHONEBOOK

hs ringer

PHONEBOOK

hs ringer

PHONEBOOK

ringer

PHONEBOOK

NEW

C LEAR

C I

PHONEBOOK

then

select

DELETE

Provider mode

Press

then

Press

then

Press

to select Tick (ON) or Cross (OFF)

handset

If you have programmed a prefix code into the base unit , you need to turn provider

mode on for each handset if you want it automatically to dial the prefix whenever

you dial a number beginning with 0.

PROV MODE

Prefix number

This may be useful if you use a dialling prefix to route your long-distance calls via a

service provider other them the one which supplies your line. You can program this

prefix into the base unit. Then when you turn on Provider Mode on individual handsets

the prefix will automatically be dialled out at the beginning of any phone number

starting with 0.

he display shows

and any prefix

that¡¯s

If necessary, use

to clear digits from the

display. Then key in the

prefix and confirm using

Press

then

Press

then

Press

base

already been set.

–

F /C

CHARGE

handset's batteries are

beingcharged.

IN USE

nne

telephone line.

Symphony2200

Symphony2200 — don’t

MENU button

Comes on when the

Comes on when you

Switch the Speakerphone on and off

◗

During a call, you can press to switch the speakerphone on, the

symbol will appear on display.

◗

Press when speakerphone on, the speakerphone will turn off and

the symbol disappear from display.

The speakerphone won't work if the batteries are low.

NU MBER1

NU MBER2

ACTIVATION

NO BAR

LOCAL

INTERNAL

PREFI NUM

PREFI NUMBER

Press to switch speakerphone

on or off.

Press to make all registered handsets

(

)

ring, this is usefull if you've forgotten

where you put a handset.

Your handset's loudspeaker on.

melody

If you have a Broadband line

noh

elet yr

ve ,

dnabdaorb htiw

h a nI

tsu

,de

enn

oy taht tn

iop

t eh

eno

deen

cenn

bro

cro

rs,

you

oadband

supp

If you connect your telephone to a line with

you will need to

insert a microfilter(not included) between the telephone

between

which could cause problems.

a broadband connection,

and the

telephone line, otherwise you may get interference

the telephone and the broadband,

Binatone SYMPHONY 2200 Manuel utilisateur

Marque: Binatone

Modèle: SYMPHONY 2200

Catégorie: Téléphones

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Binatone SYMPHONY 2200 User manual

Binatone SYMPHONY 2200 Manuel utilisateur

Binatone SYMPHONY 2200 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents