Binatone E800 Manuel utilisateur

Marque: Binatone

Modèle: E800

Catégorie: Téléphones

Taper: Manuel utilisateur

Important note — emergency calls

The e800 is not designed for making emergency calls when the

mains power fails. So you should make alternative arrangements

for access to Emergency Services.

(This means that you should also have a basic phone that does not

need mains power, connected to your line so that you can make

calls during a power failure.)

e800

USER GUIDE

Digital cordless telephone

If you need help …

http://www.binatonetelecom.com/

The is available from

9.00 am to 5.00 pm, Monday to Friday, on

Calls are charged at Local Call rate.

Or visit our website:

Binatone Help Line

0845 345 9677

Before you can use the handset to

make calls you will need to fit and

fully charge the batteries, as

described in Section 3.

Please read the notes in Section 2

before you install the base unit.

11 Customising your handset

General points

You can customise the settings of your e800 handset and base unit, using a

menu which is shown on the handset’s display. Please note that:

■

If you don’t press any button for about 25 seconds, the handset will time out

and the display will return to standby mode.

■

When you confirm any setting you have made, you’ll hear a confirmation

tone. If you make a mistake, you’ll hear a warning tone.

■

At the end of each set of steps, you can return the handset to standby mode

by either replacing the handset on the base unit, or pressing and holding the

HANG UP/C button.

Auto-answer

When a call comes in, you need to press any button to answer it. Or you can set

auto-answer — so, if the handset is in place on the base unit, you simply lift it to

answer the call, without pressing any button.

1 Press PROG then 1 5

2 Use  or  to set:

0 for auto-answer off

1 for auto-answer on

3 Press PHONE/OK to confirm

Ringer volume and melody

The handset has eight ringer volume levels, including 0 for off; and eight ringer

melodies. With the volume set to 0, the handset won’t ring for incoming calls,

but the display will show call or the phone number.

To change the volume:

1 Press PROG then 1 1 1

2 Use  or  to change the volume

3 Press PHONE/OK to confirm

To change the melody:

1 Press PROG then 1 1 2

2 Use  or  to change the melody

3 Press PHONE/OK to confirm

Key tone

Normally, whenever you press a button on the handset, you hear a ‘beep’ tone.

You can turn these tones off if you prefer.

1 Press PROG then 1 1 3

2 Use  or  to set:

0 for key tone off

1 for key tone on

3 Press PHONE/OK to confirm

Direct Call

With Direct Call turned on, when you press any key except the PROG button,

the handset will automatically make a call to a number you have programmed

in. This feature is sometimes called babysitter’s call.

With Direct Call turned on, it is not possible to make emergency calls,

unless you have programmed an emergency number such as 999 as the

Direct Call number. But remember that the number you have

programmed will be dialled automatically when any key is pressed.

Before you can turn Direct Call on, you must program the telephone number.

To program the number:

1 Press PROG then 1 3

2 Key in the number

You can press the HANG UP/C button to clear digits one by one; or press and

hold the HANG UP/C button to clear the Direct Call number completely.

3 Press PHONE/OK to confirm

To turn Direct Call on and off:

1 Press PROG then 1 2

2 Use  or to set:

0 for Direct Call off

1 for Direct Call on

3 Press PHONE/OK to confirm

While Direct Call is turned on, the display shows and the Direct Call number.

You can answer calls as normal.

Customising your handset, continued

To clear all memories

This is a way of clearing all stored numbers at once, from the memory locations

and the Last Number Redial memories. If you have set a Direct Call number, it

will be cleared too.

1 Press PROG then 1 9

2 Press PHONE/OK to confirm

Note: Caller ID memories are cleared by resetting the base unit (Section 12).

To reset the handset

When you reset the handset, you return all its settings to their defaults:

Ringer volume — 7. Ringer melody — 4. Key tone — on.

Indirect Network (Section 13) — off . Auto-answer — off.

Select base unit — automatic (best connection).

1 Press PROG then 1 0

2 Press PHONE/OK to confirm

12 Customising your base unit

Emergency numbers

These two numbers can be dialled even when call barring is set.

1 Press PROG then 2 2 3 1

2 Key in the first emergency number

3 Press PHONE/OK to confirm

4 Press 2 3 2

5 Key in the second emergency number

6 Press PHONE/OK to confirm

Ringer volume and melody

The base unit has eight ringer volume levels, including 0 for off; and eight ringer

melodies. With the volume set to 0, the base unit won’t ring for incoming calls.

To change the volume:

1 Press PROG then 2 1 1

2 Use  or  to change the volume

3 Press PHONE/OK to confirm

To change the melody:

1 Press PROG then 2 1 2

2 Use  or  to change the melody

3 Press PHONE/OK to confirm

Call barring

You can set call barring for individual handsets registered to your base unit.

There are two kinds of call barring:

■

You can bar calls to up to two specific numbers (which can be dialling codes)

with up to eight digits each. With this option, you need to program in the

numbers first, then turn the barring on and off.

■

You can bar certain types of call — no outside calls, or no international calls.

When either kind of call barring is turned on, you may not be able to make a

call, and you may see a ‘key’ symbol on the display.

To bar calls to specific numbers

1 Press PROG then 2 2 2

2 Key in the handset number (1 to 6)

3 Press 1 1

4 Key in the first barred number

5 Press PHONE/OK to confirm

6 Press 2 2

7 Key in the handset number (1 to 6)

8 Press 1 2

9 Key in the second barred number

10 Press PHONE/OK to confirm

To turn specific number barring ON and OFF:

1 Press PROG then 2 2 2

2 Key in the handset number (1 to 6)

3 Press 0 then use  or  to set:

0 for call barring OFF

1 for call barring ON

4 Press PHONE/OK to confirm

To turn barring of certain types of call ON and OFF

1 Press PROG then 2 2 1

2 Key in the handset number (1 to 6)

3 Use  or  to set:

0 no outside calls (intercom calls only)

1 no international calls

2 all calls allowed (call barring OFF)

4 Press PHONE/OK to confirm

Date and time

You need to set the date and time if they are to be shown correctly on the

handsets’ displays and stored with Caller Display records.

1 Press PROG then 2 3

2 Key in the date as a six-digit number

…for example, 131002 for 13 October 2002, 020303 for 2 March 2003.

3 Press PHONE/OK to confirm

4 Key in the time as a four-digit number

…for example, 0830 for 8:30 am, 1406 for 2:06 pm.

5 Press PHONE/OK to confirm

To clear all Caller Display memories

This is a way of clearing all stored numbers from the Caller Display memories.

1 Press PROG then 2 9

2 Press PHONE/OK to confirm

To reset the base unit

When you reset the base unit, you return all its settings to their defaults:

Ringer volume — 7. Ringer melody — 4. Key tone — on. Call barring — none.

Caller Display memories — empty. Indirect Network codes — none.

1 Press PROG then 2 0

2 Press PHONE/OK to confirm

13 Indirect Network

You can use this feature if you make some of your calls via a different network

from the one that supplies your exchange line. By using indirect access to an

alternative network, you may be able to save money on long-distance and

international calls. When you subscribe to an alternative network provider, they

will send you a network access code

To route calls over the alternative network, you need to key in the access code

each time you make a call. Your e800 can do this automatically when you dial a

long-distance or international number (beginning with 0), either manually or

from memory.

For local calls (numbers not beginning with 0), the e800 will not dial the

network access code; so these calls will be routed over your local network. You

can also set two ‘local’ dialling codes, beginning with 0, for which the network

access code won’t be dialled.

The network access code and the additional ‘local’ dialling codes are set on the

base unit, and apply to all registered handsets. But you need to turn the Indirect

Network feature on and off on individual handsets.

To set the network access code

1 Press PROG then 2 4 0

2 Key in the network access code (up to six digits)

3 Press PHONE/OK to confirm

To set additional ‘local’ dialling codes

1 Press PROG then 2 4 1

2 Key in the first dialling code (up to 6 digits)

3 Press PHONE/OK to confirm

4 Press 4 2

5 Key in the second dialling code (up to 6 digits)

6 Press PHONE/OK to confirm

To turn Indirect Network on and off

You need to do this on each handset.

1 Press PROG then 1 4

2 Use  or  to set:

0 for Indirect Network off

1 for Indirect Network on

3 Press PHONE/OK to confirm

When you make a call, the handset will dial the network access code when you

dial a number beginning with 0, except when it’s to one of the ‘local’ codes you

have set. When a call is routed via Indirect Network,

LC is shown on the display.

Note — for Indirect Network to work, you must dial the phone number

(or select it from memory, LNR memory or Caller Display memory) before

you press PHONE/OK for an outside line.

16 Technical details

Standard Digital Enhanced Cordless Telecommunications (DECT)

Frequency range 1.88 to 1.9 GHz (bandwidth = 20 MHz)

Channel bandwidth 1.728 MHz

Operating range up to 300 m outdoors; up to 50 m indoors

Operating time Standby: 80 hours approx. Talking: 7 hours approx.

Battery charge time: 15 hours

Temperature range Operating 0 ºC to 40 ºC. Storage -20 ºC to 60 ºC

Electrical power

Handset — three AAA-size 300 mAH Nickel Cadmium (NiCd)

rechargeable batteries

Base unit/charger pod — input 230 V AC, 50 Hz; output

AC 9 V, 300 mA

Port specification The port (connected to the mains power supply) is a SELV

port with respect to EN41003.

The port (connected to the telephone line) is a TNV port

with respect to EN41003.

PBX compatibility Timed break recall: 100 ms (short press); 250 ms (long press).

Pause length (using the Redial/CDS button): 3 seconds.

Signalling type: DTMF (dual-tone multifrequency), also called

tone dialling.

Network connection This equipment is intended to be used in the UK only.

Operation on other countries’ PSTN termination points cannot

be guaranteed.

Declaration of conformity

The Binatone e800 complies with the essential protective requirements and objectives of:

■

EC R&TTE Directive 1999/5/EC

■

EC Low Voltage Directive 73/23/EEC

■

EC EMC Directive 89/336/EEC

and conforms to the following relevant harmonised standards:

■

Radio: TBR 6

■

EMC: EN 301489

■

Safety: EN 60950, EN 41003

■

Other: I-CTR 37

Binatone Telecom plc operates a policy of continuous product improvement, and so

reserves the right to make changes to the product and functions without notice.

18 Troubleshooting

The e800 must be serviced by trained engineers. NEVER attempt any

repairs or adjustments yourself — you could make the problem worse and

invalidate the Guarantee.

ALWAYS check first that:

■

you have followed all the steps in Section 3 to install and set up your e800

■

all connectors are firmly inserted in their sockets

■

mains power is switched on at the socket

■

the handset’s batteries are correctly and securely installed, and aren’t run down

Everyday use

“I can’t make or

answer calls.”

If the handset’s display is blank, it may be switched off. Press the

HANG UP/C button to switch it back on.

Check that the base unit’s mains power adapter is plugged in

and power is switched on. The base unit needs mains power for

normal operation of the phone — not just for charging the

batteries.

Make sure you’re using the telephone line cable that was sup

plied with your e800. Other telephone line cables might not work.

Move the handset closer to the base unit.

Check the Battery Level symbol on the display. If it is low,

replace the handset on the base unit or charger pod to recharge

the batteries.

Switch off power at the mains socket, wait for a few seconds

and then switch back on. This may solve the problem.

“I can’t make a

call.”

The handset’s keypad may be locked (see Section 4). Unlock it

before you make a call.

Call barring to specific numbers may have been turned on.

Barring of certain types of call (international, or all outside calls)

may have been turned on.

“When I press

keys, nothing

happens.”

Make sure the batteries are fitted in your handset. If the Battery

Level symbol on the display shows ‘low’, recharge the batteries.

“When I key in a

number, it

appears on the

display, but I

can’t make an

outside call.”

Try moving the handset closer to the base unit.

Try a different position for the base unit — somewhere higher if

possible, or further from other electrical equipment.

Call barring to specific numbers may have been turned on.

Barring of certain types of call (international, or all outside calls)

may have been turned on.

“The phone does

not ring”

Check that the base unit’s mains power adapter is plugged in

and power is switched on. The base unit needs mains power for

normal operation of the phone — not just for charging the

batteries.

Make sure you’re using the telephone line cable that was

supplied with your e800. Other telephone line cables might not

work.

Check that the total REN value of all equipment connected to

your telephone line is no more than 4. Disconnect one or more

telephones and see whether that helps.

“My call was cut

off. Now I can’t

use my handset.”

If you went out of range, move the handset closer to the base

unit before you try again to make a call.

“There is inter

ference and noise

on the line.”

Move the handset closer to the base unit, or to a different position.

Try moving the base unit so that it’s not near other electrical

equipment, such as a television or a computer.

You’ll get the best results if you site the base unit as high as

possible. For example, in a two-storey house, the first-floor

landing is an ideal place for the base unit.

“I hear ‘beeps’

from my handset

while I’m on a

call.”

You may be going out of range of the base unit. Move closer, or

your call may be cut off.

Check the Battery Level symbol on the display. If it is low,

recharge the batteries.

“The Caller

Display feature

isn’t working.”

You need to subscribe to the Caller Display feature from BT or

your service provider.

The caller may have withheld their number by dialling 141. Or

they may be calling from a network that does not transmit the

Caller ID (for example, it may be an international call).

“When I try to

make a call, I hear

Busy tone.”

If you’re using a e800 Twin system, or have extra handsets

registered to your base unit, check that another handset isn’t

already in use on a call.

“The volume is

low when I’m on

a call.”

Make sure you’re holding the earpiece correctly over your ear.

Adjust the volume using the  or  button.

Using a multi-handset system

“I can’t transfer a

call.”

Make sure the other handset is in range of the base unit.

Make sure you’re dialling the correct number for the other

handset (1 to 6, or 9 for all registered handsets).

Batteries

“The handset‘s

battery pack is

running low

within an

hour or two.”

Before you first used the handset, you should have left it on the

base unit or charger pod for up to 15 hours to charge the

batteries fully.

You may need to replace the batteries (see below).

Clean the battery charging contacts with a dry cloth.

Check the connections between the base unit and the mains

power socket.

“I try to recharge

the batteries, but

I still get a

warning that they

are low.”

You need to replace the batteries. To find out how to obtain

replacements, call the Binatone Spares Department on

0845 345 9677, between 9.00 am and 5.00 pm, Monday

to Friday.

Dispose of used batteries safely — never burn them, or put

them where they could get punctured.

DON’T use non-rechargeable batteries in your e800 — they

may burst, causing damage.

Indirect Network

“The Indirect

Network feature

isn’t working.”

You must subscribe to an alternative network provider before

you can use this feature.

If you have more than one registered handset, you need to turn

the feature on for each one individually, as well as setting the

network access code on the base unit.

When making a call, you must dial the number (or select the

number from memory, LNR memory or Caller Display memory)

before you press the PHONE/OK button for an outside line.

PBX use

“The Recall

function doesn’t

seem to work.”

You may need to press and hold the R button for a couple of

seconds, rather than pressing it briefly. Try this and see if it

works.

“Last Number

Redial and/or

memory dialling

don’t work on

a PBX.

When you first make a call, press the Redial/CDS/P button for a

pause between the outside line access code (e.g. 9) and the tele

phone number. You should later be able to redial the number.

When storing numbers in memory, you can include the outside

line access code (e.g. 9) with each number.

If your PBX requires you to wait for a second Dial tone before

dialling the telephone number, press the Redial/CDS/P button

for a pause between the access code and the number.

You can also set up your e800 so that it automatically inserts a

2-second pause after you dial the outside line access code, as

follows:

1 Press PROG then 2 5 0

2 Key in the line access code (up to four digits)

3 Press PHONE/OK to confirm

If the fault persists …

■

Disconnect all other instruments connected to the same line as the e800

and see whether you can make a call.

■

Disconnect the base unit from the telephone line and plug a different phone

into the master telephone socket. Try making a call. If this works, the line is

OK.

■

If the call does not work, and you are using a two-way socket adapter,

remove it and plug a telephone directly into the socket. If the call now works,

the adapter may be faulty.

■

If you cannot make a call, the fault may be on the exchange line. Contact the

service provider (the BT engineers on 151, or your cable company).

■

If you still cannot identify the cause of the problem, contact the Binatone

Help Line on 0845 345 9677.

17 Guarantee and service

The Binatone e800 is guaranteed for 12 months from the date of purchase

shown on your sales receipt. The Guarantee does not cover damage by misuse

or negligence, or by excessive voltages — for example, faults on the telephone

line, or lightning.

Please keep your sales (till) receipt — this is your guarantee. You should also

keep the original packaging material.

In the unlikely event that you need to return your e800 to our Repair Centre

while it is under guarantee, there will be a £5 handling charge.

While the unit is under Guarantee

1 Disconnect the base unit from the telephone line and the mains electricity

supply

2 Pack up all parts of your e800, using the original packaging. Remember to

include the mains adapter

3 Return the unit to the shop where you bought it, making sure you take your

sales receipt

After the Guarantee has expired

If the unit is no longer under Guarantee, first follow steps 1 and 2 as for repair

under Guarantee. Then …

3 Call our Service Department on 0845 345 9677 and ask for a quotation of

the repair charge and details of where to send your e800 for repair

4 Make sure you include with your e800: your name and address; a cheque

or postal order for the value of the repair charge

5 Return your e800 to the address given by the Service Department

Waste electrical products must not be

disposed of with household waste.

This equipment should be taken to

your local recycling centre for safe

treatment.

14 Cleaning and care

■

Do not clean any part of your e800 with benzene, thinner or other solvent

chemicals — this may cause permanent damage which is not covered by the

Guarantee. When necessary, clean it with a damp cloth.

■

Keep your e800 away from hot, humid conditions or strong sunlight, and

don’t let it get wet.

■

Every effort has been made to ensure high standards of reliability for your

e800. However, if something does go wrong, please do not try to repair it

yourself — consult your supplier or the Binatone Help Line.

15 Connection and conditions for use

You can connect your e800 to a direct exchange line (DEL) — a line connected

to a local exchange, with its own phone number; to an extension socket con

nected to a DEL; or to an extension on an approved compatible PBX. Do not

connect the e800 as an extension to a payphone.

The ringer equivalence numbers (RENs) of all instruments (phones, fax

machines, etc.) connected to an exchange line must not add up to more than

4 — otherwise, one or more of them may not ring and/or answer calls correctly.

The e800 has a REN of 1, and most other telephones have a REN of 1 unless

marked otherwise.

Contents of this User Guide

1 Where to find it

2 Before you start

3 Installation

4 Switching on and off

5 Making and answering calls

6 Last Number Redial

7 Caller Display

8 Memory dialling

9 Intercom, transfer and conference

10 Handset registration

11 Customising your handset

12 Customising your base unit

13 Indirect Network

14 Cleaning and care

15 Connection and conditions for use

16 Technical details

17 Guarantee and service

18 Troubleshooting

May 2005

E:\Binatone2005\e800_A2\e800_A2_01.vp

10 May 2005 15:47:09

Color profile: Generic CMYK printer profile

Composite Default screen

If the display is blank

Press the button to switch the handset on

SCROLL ( ) buttons#

When a long number (more

than 16 digits) is shown on

the display, press these to

scroll along the digits.

PROG button

Press to start programming.

Press during a call to make a note

of a number in the Notebook.

/INT (Intercom) button

Press to make an intercom call

(if you have more than one

handset).

PHONE /OK button

Press to begin or answer a

telephone call.

Press while programming to confirm

your selection.

UP and DOWN buttons

Press during a call to adjust the volume in

the earpiece.

Press to move through the list of stored

numbers or Caller Display records.

(Last Number Redial)/

CDS/ PAUSE button

Press ONCE to make a repeat

call to one of the last five

numbers you dialled.

Press TWICE to see a list of

Caller Display records.

Press to generate pauses when

using the phone on a PBX.

HANG UP / C (Cancel) button

Press to hang up at the end of a call.

Press and hold for 1 second to lock the keypad.

Press and hold for 3 seconds to turn the handset on and off.

While dialling or programming, press BRIEFLY to delete digits from

the display; or press and HOLD to clear the display.

HANDSET LOCATOR button

Press to make all registered handsets ring (see below).

R (Recall) button

eYou may need this during a call if your 800 is

connected to a PBX, or if you use BT’s Select Services.

IN USE light

This comes on when you have a connection to the telephone line.

MEMORY button

Press to store numbers in memory and to make

calls to stored numbers.

Ringer

Where to find it1

When this shows ‘nearly empty’ ( ), put the handset onto

the base unit or charger pod as soon as possible, to charge the

batteries. While the batteries are being charged, this symbol

blinks.

The handset’s number

(1 if you have a single

system, 1, 2 or 3 if you

have a Twin or Triple

system)

The time is shown if you’ve

set the handset’s clock

The base unit’s number (1,

unless you have registered

your handset to more than

one base unit)

Intercom

call

Memory/

store

Indirect

network

Redialling

Caller

Display

This appears when the handset is dialling a non-local number

via an alternative network.provider’s

This appears when you’re using Last Number Redial.

This appears when you’re checking, or dialling from, the list of

Caller Display records.

This appears when the keypad is locked, or when you’re trying

to dial a barred number.

This flashes while your handset is ringing for an intercom call,

and comes on steadily when the call’s connected.

This comes on when you’re storing numbers in memory, and

when you’re making calls to stored numbers.

Keypad

locked

Signal

level

This shows the strength of the signal between the handset and

base unit. It flashes while the handset is trying to establish a

radio link .

to the base unit If this symbol flashes while you’re

on a call, move closer to the base unit

Battery

charge

level

New call

This appears when you missed incoming calls (even if you do

not use Caller Display).

What the symbols mean

The duration of each call is shown on the display from 20 seconds

after you press the PHONE button for a line, until 5 seconds after

you end the call.

… and symbols on the display

To page all handsets from the base unit

To make all registered handsets ring (this is useful if you’ve forgotten

where you put a handset):

Handsets ring for up to 30 seconds. To stop the ringing before

this time:

Press the HANDSET LOCATOR button

Press the HANDSET LOCATOR button again OR press any

button on any handset

The e8000 base unit and charger pod must

be used with the mains adapters supplied.

Using any other adapters will result in non-

compliance with EN60950, and will invalidate

any approval given to this apparatus.

Installation3

Choose a suitable site for the base unit

See above

Plug the mains adapter into a 230 V AC,

50 Hz mains socket, with the switch on

the socket set to OFF

Plug the mains adapter into a 230 V AC, 50 Hz mains

socket, with the switch on the socket set to OFF

Switch on at the mains socket(s)

If you have one or more charger pods …

Connect the mains power lead

and the telephone line cord into

the underside of the base unit

Use the telephone line cord

supplied with your 800 — do not

use any other telephone line cord

See the note

on page 4

Fit the rechargeable batteries in each handset

+–

. Fit the three

batteries as

shown, making

sure you match

the and ends

to the markings

in the battery

compartment

B. Fit the battery

compartment cover,

sliding it into place

and pressing firmly

to make sure it is

secure

Charge the batteries for 15 hours

The battery charge level symbol should

increase by one bar every half hour when

you’re charging an empty battery. If you

think that the symbol isn’t showing the

correct battery charge level, remove and refit

the batteries.

Before you use the handset for the

first time, it’s important to charge

the batteries fully.

The handset ‘beeps’ when it’s

correctly in position on the charging

cradle.

Leave the handset on the charging cradle

for 15 hours.

The battery

level symbol

blinks

Make sure the mains socket is

switched on if you want to use

the phone — it will not work

without electrical power

Connect the base unit to the telephone line

Switch off power at the mains socket

Insert the telephone line plug into

the socket as shown

Switch mains power back on

Use the plug to

raise the shutter

before pushing

it into the socket

NOTE: the charger pod does not have

a connection to the telephone line.

Only use the rechargeable batteries supplied with

the handset. DON’T use non-rechargeable batteries

— they may burst, causing damage.

The Charge

light comes on.

2 Before you start

Unpacking your e800 system

In the box are:

■

the cordless handset (up to six, depending on which e800 system you have

bought)

■

the base unit

■

three rechargeable batteries and a battery compartment cover for each

handset

■

a telephone line cable for the base unit

■

a mains power lead and adapter for the base unit

■

up to five charger pods, each with a separate mains power lead and adapter.

Keep the packaging materials in a safe place in case you later need to transport

the unit.

Keep your sales (till) receipt, which is your guarantee.

Positions for the base unit and charger pod

The base unit and charger pod should each be placed on a level surface, in a

position where:

■

the mains adapter plug will reach an easily accessible 230-V AC switched

mains supply socket — never try to lengthen the mains power cable

■

the telephone line cable will reach your telephone line socket or extension

socket (base unit only; charger pods have no connection to the telephone line)

■

it is not close to another telephone — this can cause radio interference

during calls

■

it is not close to a sink, bath or shower, or anywhere else where it might get

wet

■

it is not close to other electrical equipment — fridges, washing machines,

microwave ovens, TVs, fluorescent lights, etc.

To use your handset and base unit together, you must be able to establish a

radio link between them. Be aware that:

■

Siting the base unit as high as possible will give better results — for example,

in a two-storey house, the best position may be on the first-floor landing.

■

Any large metal object — like a refrigerator, a mirror or a filing cabinet —

between the handset and base unit may block the radio signal.

■

Other solid structures, like walls, may reduce the signal strength.

4 Switching on and off

To switch the handset on and off

To switch the handset off and save battery power:

◗

Press HANG UP/C and hold it for 3 seconds until the display goes

blank

To switch the handset back on:

◗

Briefly press HANG UP/C

To lock the keypad

To lock the keypad:

◗

Press HANG UP/C and hold it for 1 second until the key symbol

and a group of dashes appear on the display

To unlock the keypad:

◗

Press HANG UP/C and hold it for 1 second until the key symbol

disappears from the display

◗

Or simply replace the handset on the base unit or charger pod

Notes

■

When the handset is switched off, it can’t be used for making calls, including

emergency calls.

■

When the handset is switched off, it won’t ring for incoming calls, but the

base unit will still ring. To answer a call when the handset is switched off, you

need to switch it back on. Remember that it may take a few moments for the

handset to re-establish a radio link with the base unit.

■

When you don’t need to use the handset (for example, overnight or when

you go out), replace it on the base unit or charger pod, to keep the batteries

charged

5 Making and answering calls

To make a call

1 Key in the telephone number

If you make a mistake, press the HANG UP/C button to clear digits one by

one from the display.

2 Press PHONE/OK

(You can dial the number after you press the PHONE/OK button to get Dial

tone if you prefer, but you won’t be able to correct any mistakes if you do it

this way.)

If you want to use the Indirect Network feature, refer to Section 13.

To answer a call

When there’s an incoming call, call or the phone number (if you subscribe to

Caller Display: see Section 7) flashes on the display; and the base unit and

handset ring.

◗

Press any button to answer the call

To end a call

◗

Press HANG UP/C so the IN USE light on the base unit goes out

◗

Or simply replace the handset on the base unit or charger pod

Earpiece volume

During a call, to adjust the volume in the earpiece:

◗

Press  or  There are three volume levels, shown by bars on the

left-hand side of the display. After you end your call,

the earpiece volume will stay at the level you have set.

6 Last Number Redial

To make a repeat call to the last number you dialled (up to 24 digits):

1 Press Redial/CDS

2 Press PHONE/OK

To make a repeat call to one of the the last five numbers you dialled:

1 Press Redial/CDS

2 Press  or  if necessary until the number you want is displayed

3 Press PHONE/OK

To clear a number from the Last Number Redial (LNR) memories:

1 Press Redial/CDS

2 Press  or  until the number is displayed

3 Press and hold HANG UP/C until you hear a tone;

OR press and hold HANG UP/C for 5 seconds to clear all five LNR

memories

Notes

■

Only numbers you’ve dialled manually will be stored in the LNR memories;

not numbers you’ve dialled from memory or from the Caller Display list.

■

Numbers you’ve dialled more than once will be stored only once.

■

Each time you dial a number, it clears the oldest one from the LNR memories;

so you don’t need to clear numbers manually unless you want to.

8 Memory dialling

You can store up to 20 phone numbers in memory. Each number can have up to

24 digits. The 20 memory locations are numbered 01 to 20.

To store a number

1 Key in the phone number

If you make a mistake, press the HANG UP/C button to clear one digit at a

time from the display.

2 Press and hold MEMORY for at least a second

The phone number appears on the display, with the first free memory

location to the left of it. To store it in a different location, use the

 or 

button to move to the one you prefer.

3 Press PHONE/OK to confirm

To make a memory call

1 Press MEMORY briefly

Two dashes flash on the left side of the display

2 Either press  or  to find the number you want;

OR key in a two-digit memory location number (01 to 20) using the

numbered keys

3 Press PHONE/OK

Chain dialling

You can store part of a number (for example, the long-distance dialling code)

in memory, and use any combination of memory and manual dialling to make

a call.

To change a stored number

1 Press PROG

2 Press MEMORY

3 Press  or  until the number you want to change is displayed

4 Press HANG UP/C to delete digits one by one; then key in the

new digits

5 Press PHONE/OK

To delete a stored number

1 Press MEMORY

2 Press  or  until the number you want to delete is displayed

3 Press and hold HANG UP/C until you hear a tone and the number

disappears from the display;

OR press and hold HANG UP/C for 5 seconds to clear all memories

To use the notebook

You can store a number in memory while you are busy on a call.

1 Press PROG

2 Press MEMORY

3 Press  or  to find a free memory location;

OR key in a memory location number using the numbered keys

4 Key in the phone number you want to store

5 Press PHONE/OK to confirm

Note: If you want to quit the notebook without storing a number, press the

HANG UP/C button for one second.

To store an LNR number in memory

You can move a number from the Last Number Redial (LNR) memories to a

more permanent memory location.

1 Press Redial/CDS

2 Press  or  if necessary until the number you want is displayed

3 Press and hold MEMORY for one second

The display shows a free memory location. You can press

 or  to

select a different free location if you wish (only free locations are displayed).

4 Press PHONE/OK to store the number

To store a Caller Display number in memory

1 Follow steps 1 to 3 in ‘To check Caller Display records’ (Section 7) to

display the number

2 Press and hold MEMORY for one second

The display shows the first free memory location. You can press

 or 

to select a different free location if you wish (only free locations are displayed).

3 Press PHONE/OK to store the number

7 Caller Display

If you subscribe to this feature from your service provider, you can see the phone

numbers of your callers on the display, before you answer. If a caller withholds

their number by dialling 141, or if they are calling from a network that does not

transmit the number, no number will be shown on the display when the phone

rings.

The e800 will store the numbers of the last 10 callers (whether or not you

answered the call) so you can call them back later. When all 10 Caller Display

memories are full, the next incoming number will overwrite the oldest one. If the

number was withheld or unavailable, no record will be stored.

If you’ve got new Caller Display records, the symbol is shown on the display.

To check Caller Display records

1 Press Redial/CDS TWICE

The most recent caller’s number is shown on the display.

2 Press STAR to switch between the number, and the time/date of

the call

If the number had more than 13 digits, you’ll see the first 13 digits of the

number when you press Ø once; press it again to see the time/date.

3 Press  or  to scroll through the records

When you’ve checked all the records, the

CID

symbol disappears from the display.

To return a call

To ring back someone who’s called you:

1 Follow steps 1 to 3 above to display the number

2 Press PHONE/OK to dial the number

To delete Caller Display records

To delete a Caller Display record:

1 Follow steps 1 to 3 above to display the number

2 Press and hold HANG UP/C until you hear a tone;

OR press and hold HANG UP/C for 5 seconds to clear all records

9 Intercom, transfer and conference

If you have an e800 multi-handset system, you already have up to six handsets

registered to your base unit. You can register additional handsets — altogether,

up to six handsets per base unit. With two or more handsets registered, you can:

■

make intercom calls from one handset to another

■

transfer an outside call from one handset to another

■

shuttle between an outside call and an intercom call

■

set up a three-way conference call

Each handset’s number (h1 to h6) is shown on its display.

The ringing tune for intercom calls is different from that for outside calls. When

someone makes an intercom call to you

INT appears on your handset’s display,

and you can answer and end the call as normal.

Only one handset can be connected to the outside line at once. If you try

to make a call while another handset is using the line, you’ll hear Busy tone.

Some of the instructions in this section tell you to press a button ‘for one

second’. This means you should press the button and hold it down until

the display changes, you hear a tone, or you’re connected to another call.

To make an intercom call

1 Press Ø/INT for one second

INT appears on your handset’s display, with the numbers of all other

registered handsets.

2 Key in a handset number; OR press 9 to call all other registered handsets

The other handset rings, and the

INT symbol flashes on its display. When

the other handset user answers, you will be connected.

To transfer a call

When you’ve made or answered an outside call, to transfer it to another handset:

1 Press Ø/INT for one second then key in the number of the other

handset

The outside call is put on hold and the other handset rings. When the user

answers, you can speak to her/him. If the user does not answer, you can get

back to the outside call at any time by pressing and holding Ø/INT again.

2 Press HANG UP/C to hang up and transfer the call

You can press the HANG UP/C to transfer the outside call before the other

user answers your intercom call. If the user hasn’t answered after 30 seconds,

the outside call will come back to you and your handset will ring.

To shuttle between two calls

When you have both an outside call and an intercom call in progress, you can

shuttle from one to the other, like this:

◗

Press Ø/INT for one second to speak to each in turn, putting the

other on hold

You can transfer the outside call to the other handset by pressing

HANG UP/C while you’re connected to the intercom call.

If you press HANG UP/C while you’re connected to the outside call, you’ll

disconnect it.

To set up a three-way conference

To set up a three-way conference between yourself, an outside call and an

intercom call with another handset::

◗

Press (HASH) for one second

To suspend the other handset user from the conference call:

◗

Press for one second

You remain connected to the outside call. If the other user has not hung

up, you can bring her/him back into the conference by pressing # again.

OR, to drop out of the conference call, leaving the other user connected to the

outside call:

◗

Press HANG UP/C

New Call tone

When you are on an intercom call and an outside call comes in, you will hear

New Call tone over your conversation to tell you that someone is calling you.

To answer the outside call and end the intercom call:

◗

Press R briefly

OR, to answer the outside call and put the intercom call on hold (so you can

later use shuttle, conference or transfer):

◗

Press Ø/INT for one second

10 Handset registration

The handset(s) supplied with your e800 base unit are already registered — the

first one as handset number 1, the second as number 2. You don’t need to re-

To check whether a handset is registered, make sure mains power to the base

unit is switched on and the handset is within range. The handset’s display should

show its number, and the ‘signal level’ symbol on the display should show three

bars. If the display shows Out of range continuously, you need to re-register

the handset.

To register a new handset or to re-register a handset

1 Press and hold the HANDSET LOCATOR button on the base unit

You hear Registration tone (slow ‘beeps’).

You now have 30 seconds in which to register the handset.

2 On the handset, press PROG then 1 6

followed by the base unit number (1)

(Or, if the handset is already registered to a different base unit, key in a new

base unit number — 2, 3 or 4.)

3 Key in 0000 (the base unit’s PIN)

4 Press PHONE/OK

The display shows the handset numbers which are free on the base unit.

5 (Optional) Key in a handset number

If you don’t key in a number at this point, the handset will be registered with

the lowest free number.

The handset beeps to confirm registration.

To de-register a handset

You may need to do this in order to replace a faulty handset.

1 Press PROG then 2 6

The display shows the numbers of all handset registered to the base unit.

2 Key in the number of the handset to be de-registered

The display flashes, and the handset is de-registered.

To select a base unit

If your handset is registered to more than one base unit, it will automatically

select the one with which it can best set up a radio link (usually the nearest one).

Or you can select a base unit manually.

You don’t need this function if you have only one base unit.

1 Press PROG button then 1 7

2 Use  or  to select a base unit

Base units are numbered 1 to 4.

If you select 0, your handset will automatically select the base unit that gives

the strongest connection.

3 Press PHONE/OK to confirm

To register to a different brand of base unit

Your e800 can be registered to any GAP-compatible base unit; or your can

guarantee that all features or display messages will be available using other

manufacturers’ equipment.

1 Follow the instructions in the base unit’s User Guide to put the base unit into

registration mode (for example, step 1 of the registration procedure listed

here).

2 Follow the instructions in the handset’s User Guide to register the handset

(for example, steps 2 to 5 of the registration procedure listed here).

If you need to enter a PIN code for the base unit, refer to the base unit’s User

Guide. If you have problems, contact the Binatone Help Line for more advice.

E:\Binatone2005\e800_A2\e800_A2_01.vp

10 May 2005 15:47:16

Color profile: Generic CMYK printer profile

Composite Default screen

Binatone E800 Manuel utilisateur

Marque: Binatone

Modèle: E800

Catégorie: Téléphones

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Binatone E800 User manual

Binatone E800 Manuel utilisateur

Binatone E800 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents