Krups XP420050 Manuel utilisateur

Marque: Krups

Modèle: XP420050

Catégorie: Cafetières

Taper: Manuel utilisateur

XP4200

www.krups.com

NC00026258-01

EN . . . . . . . . . . . . . . . . . p.7

FR . . . . . . . . . . . . . . . p. 27

ES . . . . . . . . . . . . . . . p. 47

WWW.KRUPS.COM

XP42

Réalisation : Espace Graphique

IFU_KR_XP4200_NAFTA_NC00026258-01 18/11/11 14:02 PageC1

PUSH

Fig.1 Fig.2 Fig.3

Fig.4 Fig.5 Fig.6

Fig.7 Fig.8 Fig.9

Fig.10 Fig.11 Fig.12

Fig.13 Fig.14 Fig.15

Fig.16 Fig.16.2 Fig.16.3

Fig.17 Fig.18.1 Fig.18.2

Fig.19 Fig.20 Fig.21

IFU_KR_XP4200_NAFTA_NC00026258-01 18/11/11 14:02 PageC4

Fig.22 Fig.23

IFU_KR_XP4200_NAFTA_NC00026258-01 18/11/11 13:47 PageC7

Filter-holder position for 1 cup

Position du porte-filtre pour 1 tasse

Posición del portafiltro para 1 taza

Filter-holder position for 2 cups

Position du porte-filtre pour 2 tasses

Posición del portafiltro para 2 tazas

IFU_KR_XP4200_NAFTA_NC00026258-01 18/11/11 13:47 PageC8

English

TABLE OF CONTENTS

1. DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p. 11

2. TECHNICAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . p. 11

3. TIPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p. 12

4. BEFORE FIRST USE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . p. 13

5. MAKING AN ESPRESSO. . . . . . . . . . . . . . . . . . . . . . . . . p. 13

6. MILK FROTHING FUNCTION . . . . . . . . . . . . . . . . . . . . . p. 16

7. CLEANING AND MAINTENANCE . . . . . . . . . . . . . . . . . . p. 18

8. DESCALING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p. 19

9. PROBLEMS, PROBABLE CAUSES

AND CORRECTIVE ACTIONS. . . . . . . . . . . . . . . . . . . . . p. 22

10. DISPOSING OF YOUR MACHINE. . . . . . . . . . . . . . . . p. 24

11. WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p. 25

IFU_KR_XP4200_NAFTA_NC00026258-01 18/11/11 13:47 Page7

English

IMPORTANT

SAFEGUARDS

When using electrical appliances, basic safety precautions

should always be followed to reduce the risk of fire, electric

shock, and/or injury to persons including the following :

1. Read all instructions prior to first use.

2. Do not touch hot surfaces. Use handles or knobs.

3. To protect against fire, electric shock and injury to persons,

do not immerse cord, plugs or machine in water or other

liquid.

4. Not intended for use by children.

5. Close supervision is necessary when any machine is used

near children. Keep machine out of reach of children.

6. This appliance is not designed to be used by children or

people without knowledge or experience with the product,

unless they are supervised or given prior instructions

concerning the use of the appliance by someone

responsible for their safety.

7. Children must be supervised to ensure that they do not play

with the appliance.

8. Burns can occur from touching hot plate, hot water or

steam. Exercise caution.

9. Exercise caution when using the steam nozzle as steam can

cause scalding.

10. Unplug machine from outlet when not in use and when

cleaning. Allow to cool before putting on or taking off parts,

before cleaning the machine, and before storing.

11. All machines are subject to stringent quality control.

Practical tests using machines taken at random are

conducted and this may explain any slight marks or coffee

residue prior to use.

12. Do not operate any machine with a damaged cord or plug

or after the machine malfunctions, or has been damaged in

any manner. Return machine to the nearest Krups Service

Center for examination, repair or adjustment or your

respective countries Consumer Service Department.

IFU_KR_XP4200_NAFTA_NC00026258-01 18/11/11 13:47 Page8

English

13. To reduce the risk of injury do not drape cord over the

counter top or table top where it can be pulled on by

children or tripped over accidentally.

14. Do not let cord hang over edge of table or counter, or touch

hot surfaces.

15. The use of accessory attachments not recommended by

Krups may result in fire, electric shock or injury to persons.

16. Do not use outdoors.

17. Do not place on or near a hot gas or electric burner, or in a

heated oven.

18. To disconnect the machine, Turn the machine OFF by

pressing the button, then remove plug from wall outlet.

Do not yank cord, instead grasp plug and pull to

disconnect.

19. Do not use this machine for anything other than it’s intended

use.

20. Do not pour liquids other than water and descaling

solutions specified in this manual into the water tank.

21. Protect the machine against humidity and freezing.

22. This machine is for household use only.

SAVE THESE

INSTRUCTIONS

IFU_KR_XP4200_NAFTA_NC00026258-01 18/11/11 13:47 Page9

English

CAUTION

This machine is intended for household use only. Any servicing

other than cleaning and user maintenance should be performed

by the nearest authorized Krups Service Center.

Visit our website at www.krupsusa.com in the USA or

www.krups.ca in Canada or contact your respective country's

Consumer Service department for the service center nearest to

you, or contact your respective country’s Consumer Service

department.

To reduce the risk of fire or electric shock, do not attempt to

disassemble the machine. Repair should be done by an

authorized Krups Service Center only.

SHORT CORD INSTRUCTIONS

A. We do not recommend using an extension cord with

this device.

B. If an extension cord is absolutely necessary,

1) the marked electrical rating of the extension cord

should be at least as great as the electrical rating

of the machine,

2) the longer cord should be arranged so that it will

not drape over the counter top or table top where

it can be pulled on by children or tripped over.

C. This machine has a polarized plug (one blade is wider

than the other). To reduce the risk of electric shock,

this plug is intended to fit into a polarized outlet only

one way. If the plug does not fit fully into the outlet,

reverse the plug. If it still does not fit, contact a

qualified electrician. Do not attempt to modify the

plug in any way.

In the interest of improving products, Krups reserves the right

to change specifications without prior notice.

IFU_KR_XP4200_NAFTA_NC00026258-01 18/11/11 13:47 Page10

English

Your Krups espresso machine is equipped with a filter-holder that has

three patented systems designed to help you make the perfect espresso

at home.

1. KRUPS Precise Tamp: gradual tamping of the espresso ground

coffee as the filter-holder is turned ensures that coffee is tamped

precisely each time.

2. Coffee ejection system under the filter-holder for clean removal of

the cake each time.

3. The filter-holder is compatible with all types of pods including

E.S.E. and soft pods.

The filter-holder is also removable and can be frequently cleaned to

maintain the filter-holder system in perfect working order. For your safety,

the filter-holder is equipped with a locking system when pressure rises.

1. DESCRIPTION

2. TECHNICAL INFORMATION

n Pump: 15 bars

n Filter-holder with grounds or pod ejection system. Compatible with

espresso ground coffee and all types of pods including E.S.E. and

soft pods.

n Steam function

a Water tank lid

b Removable water tank

c Measuring spoon

d Cup warming tray

e On/Off button with LED

indicator

f Function switch

f1. Coffee position

f2. Off position

f3. Steam preheating

position

f4. Steam position

g Brewing head

h Filter holder with grounds or

pod ejection system and gra-

dual coffee tamping system:

KPT "Krups Precise Tamp":

Compatible with ground coffee

(1 or 2 cups) and ESE or soft

pods

i Drip tray grid

j Drip tray with overflow indica-

tor

k Steam nozzle

IFU_KR_XP4200_NAFTA_NC00026258-01 18/11/11 13:47 Page11

English

n Automatic shutoff.

n Removable water tank (capacity: 0.86 litres).

n Power: 1450 W

n Voltage: 120V – 60Hz

n Anti overheating safety mechanisms

n Dimensions : H. 322,5 mm, L. 291 mm, P. 214 mm

IMPORTANT!

Operating voltage: This device is designed to work only at

alternating current 120V.

Type of use: This machine is designed EXCLUSIVELY for

household use only. Any non-residential use including

commercial purposes will void the warranty.

3. TIPS

n To extract the fullest flavor from your beans, we recommend using whole

coffee beans that have been freshly ground each time espresso is

prepared. Take care to make sure your coffee is ground to the proper

size for espresso. Too fine a grind will result in espresso that is over-

extracted and bitter. Too coarse a grind will result in espresso that is

under-extracted and weak in flavor. The perfect espresso grind will feel

like fine grains that do not clump when pressed together.

n Store your espresso grounds in an airtight container, and in a cool, dry

place to retain the flavor. Grounds should not be kept for long periods

of time as the flavor will be reduced over time.

n Do not fill your filter holder to the brim. Using the measuring spoon

included, use 1 level spoon of grounds per shot of espresso.

n If you do not use the machine for more than 5 consecutive days, rinse

and drain the water tank.

n Before removing the water tank to fill or empty it, always turn the machine

off.

n Always place the unit on a flat, stable, heat-resistant work surface.

n To obtain an espresso at exactly the right temperature, we recommend

that you preheat your cups.

IMPORTANT!

Before using for the first time, after a prolonged period

of inactivity or after descaling, the machine must be

cleaned as described in Section 4: “BEFORE FIRST

USE”.

IFU_KR_XP4200_NAFTA_NC00026258-01 18/11/11 13:47 Page12

English

4. BEFORE FIRST USE

Before using your espresso machine for the first time, clean all

accessories using warm water and a gentle dishwashing liquid, and rinse

well before replacing.

PRIMING OF YOUR MACHINE:

Use the following procedure to prime the machine:

n Open the lid and remove the water tank by lifting up on the handle

(fig.1).

n Fill it with water (fig. 2).

n Replace the water tank by positioning it firmly, to ensure the water

inlet is in place, and close the lid (fig.3).

n Press the on/off button to turn the machine on (fig.4).

n Insert the filter holder (without espresso grounds) in the machine and

turn to the right (fig.7).

n Place a container under the filter holder large enough to hold all the

water in the water tank.

n Once the machine has reached the correct temperature, the on/off

button will stop blinking. Turn the dial to the position (fig.8) and

let all the water in the tank run through.

n If the container you are using has a smaller capacity than the water tank,

turn the dial back to the to pause the water flow when necessary.

Empty the container, replace under the filter holder, and turn the dial back

to the position.

n Repeat as necessary until the water tank is empty. (fig.9).

n Once all the water has been drained from the water tank, remove and

empty the container, press the button on the filter holder and turn

the filter holder handle to the left to remove (fig.10).

5. MAKING AN ESPRESSO

In order to extract the maximum flavor from the beans, this machine

pre-infuses each cup. The pump works for 3 seconds, pauses for

3 seconds, and then continues until the cup is finished.

PREHEATING THE ACCESSORIES

For the best results, we recommend that you preheat the filter holder

before espresso grounds are added, and warm the cups.

IFU_KR_XP4200_NAFTA_NC00026258-01 18/11/11 13:47 Page13

English

n Fill the water tank with fresh cold water and turn the machine on

(fig 1-4).

n Put the filter holder in place, place the cups below.

As soon as the required temperature is achieved, the light will stop

flashing.

n Turn the dial to the position (fig.8).

n When the cups are filled with hot water, turn the dial to the position

(fig.9).

n Remove the cups, taking care to not spill the water.

n Unlock the filter holder by pressing the button on the handle while

turning the handle to the left to release, and remove the filter holder

from the machine (fig.10).

Note: Use the cup warming tray to warm espresso cups.

WITH GROUND COFFEE

The type of coffee you choose strongly influences the strength and

flavor of your espresso. Always use coffee beans ground to the

proper size for espresso. Too fine a grind will result in espresso that

is over-extracted and bitter. Too coarse a grind will result in

espresso that is under-extracted and weak in flavor. The perfect

espresso grind will feel like fine grains that do not clump when

pressed together.

Store your espresso grounds in an airtight container, and in a cool,

dry place to retain the flavor. Grounds should not be kept for long

periods of time as the flavor will be reduced over time.

Do not use instant coffee, or coffee for drip coffee machines.

n Fill the water tank to the maximum line with fresh cold water and turn

the machine on (fig. 1-4). While the machine is preheating, the light

will flash.

n Using the measuring spoon, add 1 level spoon of espresso grounds

per cup of espresso (fig.5).

n Remove any excess espresso grounds from the edge of the filter.

Important:

Do not tamp the coffee down in the filter holder. The

coffee is automatically tamped to the optimum level by

the Krups Precise Tamp (KPT) system.

IFU_KR_XP4200_NAFTA_NC00026258-01 18/11/11 13:47 Page14

English

n Insert the filter holder and turn the handle to the right as far as it will go.

You will hear a clicking sound as the Krups Precise Tamp (KPT) system

automatically adjusts the tamping level depending on the amount of

coffee grounds used. The handle will become progressively harder to

turn as you approach the optimum tamping level, do not force the handle

past this point. Use the “one cup” and “two cup” markings on the

brewing head as a guideline of where to stop. Because the Krups

Precise Tamp automatically adjusts the tamping level, you may find that

you do not always stop at the same point each time. Never turn the

handle past the far right edge of the “one cup”marking (fig.7).

n Put one or two cups under the filter holder as desired.

As soon as the required temperature is achieved, the light will stop

flashing.

n Turn the dial to the position (fig.8).

n When the cups are filled with the desired amount of espresso, turn

the dial back to the position.

n Unlock the filter holder by pressing the button on the handle while

turning the handle to the left to release, and remove the filter holder

from the machine.

n Remove the used espresso grounds using the ejection system by

holding the filter holder upside down over a trash receptacle. Press

the « PUSH » button located between the two coffee outlet nozzles

on the underside of the filter holder (fig.11). Rinse the filter holder

under running water, pressing « PUSH » while rinsing to release any

remaining grounds. Once the filter holder has been rinsed and dried

it can be refilled to prepare more espresso.

IMPORTANT: Do not store the filter holder in the locked

position when the machine is not in use to avoid

unnecessary wear to the seal.

WITH AN “E.S.E." ESPRESSO POD

“ESE” for “Easy Serving Espresso" is a packaged pod (44 mm

diameter) of 7g of selected coffee, ground and compacted between

two paper filters, specially designed to make Italian style ristretto

(tight) espressos.

This system allows for simple and clean use of your machine.

n Fill the water tank with fresh cold water to the maximum line and turn

on the machine (fig.1, 2, 3 and 4). The light will flash while the

machine preheats

IFU_KR_XP4200_NAFTA_NC00026258-01 18/11/11 13:47 Page15

English

n Remove the excess paper from the E.S.E. pod, and place the pod in

the filter holder with the red writing facing down.

n Take care to make sure that the pod is centered in the filter holder

with no paper hanging out, as this may cause leaks and/or

unsatisfactory results.

n Never use more than one pod at a time.

n Then follow the steps above for figure 7-11 to make your espresso.

WITH A SOFT POD

Your machine is also compatible with soft pods, which are usually

smaller in diameter than E.S.E. pods. However since soft pods are

not specifically designed for use with espresso machines, you will

get a less flavorful espresso than with an E.S.E. pod.

n Fill the water tank with fresh cold water to the maximum line and turn

on the machine (fig.1, 2, 3 and 4). The light will flash while the

machine preheats.

n Place the soft pod in the filter holder.

n Take care to make sure that the pod is centered in the filter holder

with no paper hanging out, as this may cause leaks and/or

unsatisfactory results.

n Never use more than one pod at a time.

n Then follow the steps above for figure 7-11 to make your espresso.

6. MILK FROTHING FUNCTION

n Steam can be used to froth milk by using the steam wand with frothing

nozzle (for example to make a cappuccino or latte).

n As the machine produces steam, the pump will make a thumping sounds.

This sound is normal and is an indication that the machine is operating

properly.

n After using the steam function, the machine purges automatically

to cool down by pumping cold water through the heating system.

During the purging cycles of cold water, the excess steam in the

heating system is released with hot water into the drip tray.

n The steam and noise that accompany this phase are important

for cooling the machine.

Caution: During and after using the steam wand, the metal

parts of the steam wand can become very hot. Take care

when handling the steam wand to avoid injury.

IFU_KR_XP4200_NAFTA_NC00026258-01 18/11/11 13:47 Page16

English

USING THE STEAM NOZZLE TO FROTH MILK

n Fill the water tank with fresh cold water to the maximum line and turn

the machine on (fig.1, 2, 3 and 4).

n Turn the dial to the position (fig.12). The indicator light will flash

to show that the machine is preheating.

n Position the steam nozzle so that it points away from the machine.

n Pour 2 to 3 oz (1/4 – 1/3 cup) of fresh milk in a small container that

is short enough to fit under the steam nozzle. Both the milk and the

container should be cold for optimum results.

n Pasteurised or UHT milk is recommended. Whole, lowfat, or skim milk

can all be frothed.

n As soon as the preheating indicator light stops blinking, plunge the

steam nozzle into the milk.

n Turn the dial to the position (fig.13).

n For optimal results, froth from the bottom of the container and slowly

move upwards. Hold the nozzle towards the bottom of the container

without touching the bottom for about 25 seconds. Then gradually

lower the container so that the steam nozzle moves up towards the

surface of the milk. Do not allow the nozzle to come completely out of

the milk, nor allow the milk level to cover the black plastic ring at the

top of the nozzle.

n Once the frothing is complete, turn the dial to the position (fig.15).

The machine will then begin 3 pumping cycles to automatically cool

the system. Once cooling is complete, another espresso can be made.

Important: To prevent clogging of the steam nozzle, make

sure the milk foam does not cover the black plastic ring at

the top of the steam nozzle.

It is important to clean the steam nozzle after each use to prevent milk

from hardening and drying inside the nozzle which can result in the tube

blowing off due to pressure build-up. To clean the nozzle :

n Place the steam nozzle in a small container filled with water.

n Turn the dial to the position (fig.12).

n Once the indicator light has stopped blinking, turn the dial to the

position (fig.13) to remove any remaining milk. Run in the steam

position for at least 30 seconds.

n Then turn the dial to th position and wipe the outside of the steam

nozzle with a clean cloth.

For thorough cleaning of the steam nozzle, see Section 7, “Cleaning of

the Steam Nozzle”.

IFU_KR_XP4200_NAFTA_NC00026258-01 18/11/11 13:47 Page17

English

7. CLEANING AND MAINTENANCE

IMPORTANT: Your espresso machine accessories are not

dishwasher-safe. Do not wash the spoon, the drip tray, the

filter holder and the water tank in the dishwasher.

CLEANING OF THE MACHINE

n Always unplug the machine before cleaning and allow to cool down

to avoid injury.

n Wipe the outside of the machine with a clean damp cloth. Do not use

harsh or abrasive cleaners, or alcohol/solvent-based cleaners to clean

the machine. Use only gentle dishwashing liquid and warm water. After

each use, rinse out the water tank and empty before replacing in the

machine.

n When a thin white layer of powder starts to form in the tank, this is a

sign that descaling is necessary. See Section 8 for details on

descaling. Please note that descaling should be performed

periodically to maintain optimum performance of your machine.

CLEANING OF THE DRIP TRAY

n The drip tray must be emptied each time the machine is used. The

presence of water in the drip tray is normal and is not the sign of a

leak. Lift up the tray slightly and pull out to remove from the machine.

n If multiple espressos are prepared one after the other, the drip tray

should be emptied every few espressos to prevent overflowing.

n The red overflow indicators in the tray will float up and become visible

to remind you to empty the drip tray before it overflows. When

emptying the drip tray, remove the metal tray and rinse out the

compartment below. If necessary, both the metal tray and the

compartment can be cleaned with warm water and a gentle

dishwashing liquid. Rinse well and dry completely before replacing

the drip tray in the machine. Make sure when replacing the drip tray

to push it all the way into the machine to avoid leaking.

CLEANING OF THE BREWING HEAD AND FILTER

HOLDER

n Both the brewing head and filter holder should be cleaned after each use.

n Wipe the brewing head with a clean damp cloth. (fig.21).

n Wash the filter holder with warm water and a gentle dishwashing

liquid.

n Do not use harsh or abrasive cleaners, or alcohol/solvent-based

cleaners to clean the brewing head or filter holder.

IFU_KR_XP4200_NAFTA_NC00026258-01 18/11/11 13:47 Page18

English

n When cleaning the filter holder, hold under running water and press

the « PUSH » button several times to remove all remaining espresso

grinds.

n Rinse well and dry carefully.

n When not using the espresso machine, do not store the filter holder

in the locked position. This will avoid unnecessary wear to the seal.

For more thorough cleaning, disassemble the filter holder:

n Remove the black plastic part with the coffee outlets and « PUSH »

button by turning it to the left and pulling (fig.22).

n Rinse the various components under running water. If necessary, use

gentle dishwashing liquid.

n Rinse and dry all components well before re-assembling.

n Replace the black plastic part in the metal part, turning in the opposite

direction to that shown in Figure 22.

n If the brewing head is heavily clogged, unscrew the grid using a

screwdriver, rinse well, dry, and then replace in the machine.

CLEANING OF THE STEAM WAND AND STEAM

NOZZLE

n This accessory consists of 2 parts: one part which is the plastic

support and the other which is the metal protection cylinder.

n Before cleaning, unlock the nozzle from the articulated arm by turning

it to the left. (fig.16, 16.2)

n Then slide the metal cylinder along the plastic support (fig.16.3).

n Clean these two parts with tap water and some mild washing-up liquid

(fig.17).

n Rinse and dry.

n Once the parts have been properly cleaned, put the metal cylinder

back on the support.

n Make sure that you don’t damage the silicone seal which makes the

nozzle watertight (fig.16.3).

n Insert the nozzle on the articulated arm then lock to the right (fig.18.1,

18.2).

8. DESCALING

The warranty does not cover machines which have become faulty

because descaling was not periodically performed.

Descale your espresso machine regularly using Krups descaling kits

(model F054), available in Krups authorized service centers (go to

Krupsonlinestore.ca for Canadian residents only).

IFU_KR_XP4200_NAFTA_NC00026258-01 18/11/11 13:47 Page19

English

In addition to two packets of descaling powder, the kit also includes a

water hardness tester to help you determine the proper schedule for

descaling your machine in normal use. The amount of scale that develops

depends on the hardness of the water used, but also the level of use.

The schedule indicated by the water hardness tester is a general

guideline only. Keep in mind that you may have to descale more

frequently than indicated.

If in doubt, it is recommended to descale every month.

DESCALING THE MACHINE

n Empty the tank and replace.

n Follow the instructions for using the Krups descaling powder inside

the kit.

n Then insert the filter holder (without espresso grounds) and lock into

place by turning to the right.

n Place a container under the steam wand to catch the water.

n Press the button to turn the machine on, and then immediately turn

the dial to the position, without stopping at the position).

n Let the mixture run through the nozzle until steam appears,

n Then turn the dial back to the position

n Place the container under the filter holder.

n Once the indicator light stops blinking, turn the dial to the position

and run half of the remaining water through.

n Turn the machine OFF by pressing the button and leave the dial at

the position. Empty the container under the filter holder then

replace it.

n After 15 minutes, turn the machine back on.

n Let the rest of the water run through until the water tank is empty.

n Then turn the dial to the position.

DESCALING FREQUENCY

Avg. number of

uses per week

Soft water

(<19°th)

Hard water

(19-30°th)

Very hard water

(>30°th)

Less than 7 Once a year Every 8 months Every 6 months

From 7 to 20 Every 4 months Every 3 months Every 2 months

Over 20 Every 3 months Every 2 months Every month

IFU_KR_XP4200_NAFTA_NC00026258-01 18/11/11 13:47 Page20

English

RINSING

IMPORTANT!

After descaling, rinse 2-3 times with clean water as

described in Section 4 “BEFORE FIRST USE”.

Then rinse the steam nozzle by following the instructions

below:

n Fill the water tank with clean water. Then place a container under the

steam nozzle.

n Press the button to turn the machine on, and then immediately turn

the dial to the position, without stopping at the position.

n Let the water run through the nozzle until steam appears.

n Turn the dial back to the position.

n The machine is now descaled and ready to be used again.

IFU_KR_XP4200_NAFTA_NC00026258-01 18/11/11 13:47 Page21

English

9. PROBLEMS, PROBABLE CAUSES AND

CORRECTIVE ACTIONS

Problems Possible causes Solutions

The espresso

is not hot

enough.

The cups and the

filter holder are

cold.

Preheat the accessories: cups and

filter holder (see paragraph 5).

The filter

holder is

locked.

You forgot to unlock

the filter.

Press « » while turning the filter

holder to the left.

The grounds

are not dry

after water has

run through.

You have not

tightened the filter

holder properly.

Tighten the filter holder by turning it

to the right as far as it will go.

The coffee

flows too

slowly.

You have tightened

the filter holder too

much.

The ground coffee

is too fine, too oily

or floury.

The filter holder is

dirty.

The water drip-

through grid is

clogged.

Loosen it slightly.

Choose a larger grind of coffee.

The perfect espresso grind will feel

like fine grains that do not clump

when pressed together.

Clean your filter holder (see

paragraph 7).

When the machine has cooled,

clean the brewing head with a

clean damp cloth (fig.21).

The water

does not run

through.

No water in the tank.

The tank is not

properly in place.

The filter is

clogged. The

ground coffee is

too fine.

Your machine

needs to be

descaled.

Fill the tank.

Replace the tank in the correct

position.

Clean the filter holder (see Section

7) and try a larger grind of coffee.

The perfect espresso grind will feel

like fine grains that do not clump

when pressed together.

Descale the machine (see Section 8).

Water leaks

from the filter

holder after an

espresso has

been made.

The dial has not been

returned to the

position.

Your machine needs

to be descaled.

Turn off your machine by moving the

dial back to the position (fig.9).

Descale the machine (see Section 8).

IFU_KR_XP4200_NAFTA_NC00026258-01 18/11/11 13:47 Page22

La page charge ...

Krups XP420050 Manuel utilisateur

Marque: Krups

Modèle: XP420050

Catégorie: Cafetières

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Krups XP420050 User manual
español: Krups XP420050 Manual de usuario

Documents connexes

Autres documents

Klipsch KPT-1802-HLS Manuel utilisateur