Jacuzzi MOF6636WCR2CPWC Manuel utilisateur

MOF6636WCR2CPWC
Jacuzzi
Marque
Jacuzzi
Modèle
MOF6636WCR2CPWC
Catégorie
Chauffe-eau
Taper
Manuel utilisateur
OPERATING MANUAL
Jacuzzi Luxury Bath
14525 Monte Vista Avenue
Chino, CA 91710
1-800-288-4002
www.jacuzzi.com
Pure Air
®
Whirlpool
Salon
®
Spa
LG74000D 06/2019
Operating Manual
English
Page 2 www.jacuzzi.com
General Operation Information. ....................................................................................................................................... 2
Reference Illustration for a Pure Air
®
System. ................................................................................................................. 3
Pure Air
®
Operations. ...................................................................................................................................................... 4
Pure Air
®
Auto-Dri™ Air Channels. .................................................................................................................................. 5
Whirlpool System Reference Illustrations. .................................................................................................................... 6-7
Whirlpool Operations. ................................................................................................................................................... 8-9
Heated Soak Reference Illustrations ........................................................................................................................ 10-11
RapidHeat™. ................................................................................................................................................................. 12
Cleaning. ....................................................................................................................................................................... 13
Maintenance. ............................................................................................................................................................ 13-14
Salon
®
Spa System Reference Illustrations .................................................................................................................. 15
Salon
®
Spa Operations. ................................................................................................................................................ 16
Troubleshooting Procedures. ........................................................................................................................................ 17
*For Spanish and French installation instructions, please visit www.jacuzzi.com/baths/support/owners-manuals/.
*Para instrucciones de instalación en español, por favor visite www.jacuzzi.com/baths/support/owners-manuals/.
*Pour directives d'installation en français canadien, veuillez visiter www.jacuzzi.com/baths/support/owners-manuals/.
Table of Contents
General Operation Information
All bathtubs manufactured by Jacuzzi Luxury Bath are designed for “ll and drain,” which means the bathtub should be
drained after each use and lled with fresh water by the next bather. This is a health precaution, as these bathtubs are
not designed to hold water continuously like pools or spas.
Close the drain and ll the bathtub until water is at least 1" to 2" (25 mm to 51 mm) above the highest jet or air inlet (see
water line indicated in the illustration - Figure 1). Do not turn on the Whirlpool or Pure Air
®
system at any time if the jets or
air inlets are not completely immersed in water. Running the Whirlpool or Pure Air
®
system when there is insufcient water
in the bathtub could result in water spraying outside the bath area.
ATTENTION: When exiting the bathtub, the water level will drop below the jets which could result in water being
sprayed out of the unit. To prevent this, you must turn unit OFF before exiting bathtub.
Fill to at least 1" to 2"
above highest jet
Fig. 1
Operating Manual
English
www.jacuzzi.com Page 3
Reference Illustration for a Pure Air
®
System
These illustrations are for reference only, as the unit comes fully assembled.
DANGER: RISK OF ELECTRIC SHOCK! Before servicing these connections, disconnect all
power supply cables to both 120 VAC services.
J2 Control Panel Pure Air
®
Schematic Diagram
J4 Control Panel Pure Air
®
Schematic Diagram
Fig. 2
CONTROL
PANEL
BLOWER
120 VAC 15A
Dedicated GFCI
Circuit Required
Fig. 3
BLOWER
CONTROL PANEL
CHROMATHERAPY
LIGHTS 2X
Auto-Dri™
SENSOR
CABLE
LIGHT CONTROL
BOX
120 VAC
Panel
LED Light
120VAC 15A
Dedicated GFCI
Circuit Required
120VAC 15A
Dedicated GFCI
Circuit Required
Operating Manual
English
Page 4 www.jacuzzi.com
Pure Air
®
Operations
J2 Pure Air
®
Controls
J4 Pure Air
®
Controls
Fig. 4
BLOWER OPERATION
• Press once to turn ON
• Press again to turn OFF
NOTE: The last blower setting used
is remembered by the system and will
automatically resume upon next use.
INCREASE TOGGLE
• Press to increase the blower inten-
sity
• Press and hold 5 seconds to set/
cancel daily Auto-Dri™
• Alternately, you can press and hold
the button to increase the intensity
level.
DECREASE TOGGLE
• Press to decrease the blower inten-
sity
• Alternately, you can press and hold
the button to decrease the intensity
level
NOTE: When switching be-
tween functions, the LED for
the newly selected function
will FLASH once to indicate
selection.
Fig. 5
BLOWER OPERATION
• Press to turn ON
• Press again to turn OFF
• Use toggles to control speed
INCREASE TOGGLE
• Press to increase selected
feature
• Press and hold 5 seconds to
set/cancel daily Auto-Dri™
• Press to increase light inten-
sity
• Press to turn ON lights at
last color used from OFF
DECREASE TOGGLE
• Press to decrease selected
feature
• Press to decrease light
intensity all the way down
to OFF
CHROMATHERAPY
• Press once to turn lights ON
at white level 2
• Press again to cycle colors
• Press again to stop at the
current color
• Press again to restart the
cycle
• Color Sequence: White,
Purple, Blue, Turquoise,
Green, Yellow, Orange, Red,
Pink, Repeat
PULSE FEATURE
• Press to turn Pulse ON
• Press to turn Pulse OFF
• +/- keys can be used to ad-
just maximum air intensity
WAVE FEATURE
• Press to turn Wave ON
• Press to turn Wave OFF
• +/- keys can be used to
adjust maximum intensity
STATUS LED
• Relays the current intensity
of selected feature
Low
1-2
Medium
Low 3-4
High
7-8
Medium
High 5-6
Operating Manual
English
www.jacuzzi.com Page 5
Pure Air® Auto-Dri™ Air Channels
J2 Auto-Dri™ Air Channels
The blower will operate for 20 minutes and then automatically shut off, unless power is manually turned off. In either
case, 20 minutes after the blower has shut off, it will turn ON for a one-minute drying cycle to blow out any water remain-
ing in the air system.
If the bath is used without the blower operating (showering or bathing without using the Pure Air
®
system), initiate the one-
minute drying cycle manually by use of the ON/OFF switch. Turn the switch ON and OFF again as you exit the bath and
the drying cycle will occur in 20 minutes.
J2 Daily Auto-Dri™ Cycle
To Activate: Holding the button for ve-seconds when the blower is off activates the daily Auto-Dri™ cycle. The blower
will start every day at the same time for one-minute. Once the daily Auto-Dri™ cycle is activated, the blower will come on
for one-second, turn off for two-seconds, come on for one-second and then turn off.
To Deactivate: Holding the button for ve-seconds when the blower is off deactivates the daily Auto-Dri™ cycle. When
the daily Auto-Dri™ cycle is deactivated, the blower will come on for one-second and then turn off.
J4 Auto-Dri™ Air Channels
The Auto-Dri™cycle is automatic and will reduce excessive accumulation of residual water in the air channels.
There are two Auto-Dri™ cycles: drain assisted Auto-Dri™ cycle and daily Auto-Dri™ cycle.
J4 Drain Assist
The Auto-Dri™ cycle is sensor assisted – two sensors (metal dials) are located near the drain of the bathtub. The sensors
detect the presence and absence of water in the bathtub.
To ensure effective and correct operation of the water sensors, it is important to keep them clean and free from block-
age or objects.
After bathing and following the emptying of the bathing well, the sensors detect a “no water” condition. A ve minute wait
time elapses and then the blower is activated. The blower will cycle through a range of speeds for 2 ½ minutes, during
which either 2 or 3 indicator lights will ash at various speeds.
• The Auto-Dri™ cycle will engage even if the blower is not used during bathing.
• The cycle may initiate more than once if the sensors become wet during any part of the Auto-Dri™ operation or during
routine cleaning of the bathtub. This is normal and does not require attention.
•
•
J4 Daily Auto-Dri™ Cycle
Each day, the blower will automatically activate a daily Auto-Dri™ cycle. The blower will operate for one minute on high
power, followed by 15 seconds at ½ power.
To set Auto-Dri™ cycle time: Wait until the time that you desire the daily Auto-Dri™ cycle to activate. With the blower off,
press and hold the plus button for ve seconds. To conrm that you have set the time, the blower will cycle between on
and off two times in a 4 second span.
To cancel daily Auto-Dri™ cycle: With the blower off, press and hold the plus button for ve seconds. To conrm that you
have cancelled the Auto-Dri™ cycle , the blower will come on for 1 second and then stop.
You must set the daily Auto-Dri™ cycle upon installation; the default is no pre-set daily Auto-Dri™ cycle.
If a power failure occurs, the system will default to no daily Auto-Dri™ cycle.
Operating Manual
English
Page 6 www.jacuzzi.com
Pushbutton Whirlpool Schematic Diagram
CONTROL PANEL
PUMP/MOTOR
120VAC 20A
Dedicated GFCI
Circuit Required
CONTROL BOX
120 VAC
PUMP
FOR MODELS
WITH IN-LINE
HEATER
OR
PUMP
PUMP/MOTOR
120VAC 15A
Dedicated GFCI
Circuit Required
Whirlpool System Reference Illustrations
Fig. 6
J2 Control Panel Whirlpool Schematic Diagram
Fig. 7
Operating Manual
English
www.jacuzzi.com Page 7
CONTROL PANEL
120VAC
PUMP
PUMP/MOTOR
CONTROL BOX
120V 20A
Decidated GFCI
Circuit Breaker
120V 15A
Decidated GFCI
Circuit Breaker
FOR MODELS
WITH IN-LINE
HEATER
CHROMATHERAPY
LIGHTS
Fig. 9
Whirlpool System Reference Illustrations (Continued)
J4 Control Panel Whirlpool Schematic Diagram
J2 Control Panel Whirlpool with Chromatherapy Schematic Diagram
CONTROL PANEL
AIR VALVE
ASSEMBLY
CHROMATHERAPY
LIGHTS 2X
LEAD CONNECTIONS
4-WHITE-C
3-BLACK-H
2-N/A
1-GREEN-GRD
VIEW A
LEAD CONNECTIONS
4-WHITE-C
3-BLACK-H
2-RED-L
1-GREEN-GRD
VIEW B
CONTROL BOX
120VAC
Pump
Panel
Blower
LED Light
PUMP/MOTOR
ILLUMATHERAPY
LIGHTS 4X
OR
120VAC 15A
Dedicated GFCI
Circuit Required
120VAC 20A
Dedicated GFCI
Circuit Required
SEE VIEW B
SEE VIEW A
OR
PUMP/MOTOR
Air Valve
FOR MODELS
WITH IN-LINE
HEATER
Fig. 8
Operating Manual
English
Page 8 www.jacuzzi.com
Fig. 11
J2 Whirlpool Controls
J2 Whirlpool Controls with Chromatherapy Controls
Fig. 12
Whirlpool Operations
CHROMATHERAPY
• Press once to turn lights ON at
white level 2
• Press again to cycle colors
• Press again to stop at the cur-
rent color
• Press again to restart the cycle
• Color Sequence: White, Purple,
Blue, Turquoise, Green, Yellow,
Orange, Red, Pink, Repeat
INCREASE TOGGLE
• Press to increase light intensity
• Press to turn ON lights at last
color used from OFF
NOTE: Default lighting color is
white level 2.
DECREASE TOGGLE
• Press to decrease light inten-
sity all the way down to OFF
NOTE: Default lighting color is
white level 2.
• Press once to turn ON.
• Press again to turn OFF.
• Press once to turn ON.
• Press again to turn OFF.
Pushbutton Whirlpool Controls
Fig. 10A
ON/OFF Button
Push down on the button to
turn ON the whirlpool system.
Push down on the button to
turn OFF the whirlpool system.
Whirlpool Control
Fig. 10B
In the closed position, the
jets massage with only
water.
In the open position, air
mixes with water to create a
deep, wide plume of
massaging bubbles.
OPEN Position
CLOSED Position
Operating Manual
English
www.jacuzzi.com Page 9
Whirlpool Operations (Continued)
J4 Whirlpool Controls
Fig. 13
NOTE: When switching be-
tween functions, the LED for
the newly selected function
will FLASH once to indicate
selection.
WHIRLPOOL
• Press to turn ON
• Press again to turn OFF
• Use toggles to control
speed*
* Whirlpool speed available
only for models equipped
with 2-speed motors.
INCREASE TOGGLE
• Press to increase selected
feature
• Press to increase light inten-
sity
• Press to turn ON lights at last
color used from OFF
DECREASE TOGGLE
• Press to decrease the
selected feature
• Press to decrease light
intensity all the way
down to OFF
LEFT AIR VALVE CONTROL
• Press to activate the left air
valve
• Use toggles to control air
mix
RIGHT AIR VALVE CONTROL
• Press to activate the right air
valve
• Use toggles to control air mix
WAVE FEATURE
• Press to turn Wave ON
• Press to turn Wave OFF
• +/- keys can be used to
adjust maximum intensity
CHROMATHERAPY
• Press once to turn lights
ON at white level 2
• Press again to cycle
colors
• Press again to stop at the
current color
• Press again to restart the
cycle
• Color Sequence: White,
Purple, Blue, Turquoise,
Green, Yellow, Orange,
Red, Pink, Repeat
STATUS LED
• Relays the current intensity of
selected feature
Operating Manual
English
Page 10 www.jacuzzi.com
Heated Soak System Reference Illustrations
J2 Control Panel Heated Soak Schematic Diagram
Fig. 14
J2 Control Panel Heated Soak with Chromatherapy Schematic Diagram
Fig. 15
CONTROL PANEL
PUMP/MOTOR
CONTROL BOX
120 VAC
Pump
120VAC 15A
GFCI
PUMP/MOTOR
CONTROL PANEL
CHROMATHERAPY
LIGHT
CONTROL BOX
120 VAC
Pump
Panel
LED Light
120VAC 15A
GFCI
Operating Manual
English
www.jacuzzi.com Page 11
Fig. 16
J2 Heated Soak Controls
J2 Heated Soak with Chromatherapy Controls
Fig. 17
Heated Soak System Reference Illustrations (Continued)
CHROMATHERAPY
• Press once to turn lights ON at
white level 2
• Press again to cycle colors
• Press again to stop at the cur-
rent color
• Press again to restart the cycle
• Color Sequence: White, Purple,
Blue, Turquoise, Green, Yellow,
Orange, Red, Pink, Repeat
INCREASE TOGGLE
• Press to increase light intensity
• Press to turn ON lights at last
color used from OFF
NOTE: Default lighting color is
white level 2.
DECREASE TOGGLE
• Press to decrease light inten-
sity all the way down to OFF
NOTE: Default lighting color is
white level 2.
• Press once to turn ON.
• Press again to turn OFF.
• Press once to turn ON.
• Press again to turn OFF.
Operating Manual
English
Page 12 www.jacuzzi.com
Whirlpool Operations (Continued)
CAUTION: Never run the whirlpool system with all the jets closed.
To adjust the direction of the jets:
• To change the direction of the water ow, swivel the jet nozzle to the desired angle (Figure 18).
To adjust the water ow to the jets:
• Increase the force of the ow by rotating the nozzle or jet face to the left (counterclockwise). Decrease the force of the
ow by rotating the nozzle or jet face to the right (clockwise). Reference Figure 19.
RapidHeat™
RapidHeat™ (Standard on Salon
®
Spa Models)
The heater turns ON automatically any time whirlpool operation is active. Heater
operation is not displayed on the control panel. There is a visible indicator light on the
heater itself that signies the heater is operating (Figure 21). The heater will help main-
tain the temperature of the water in the bathtub. It is not intended to heat the water to a
desired temperature.
Vacuum Switch
The heater is equipped with a preset vacuum switch which will not allow
the heater to turn ON if the pump is not running and water is not owing
through the whirlpool system.
High-Limit Switch
The heater includes an exclusive High-Limit switch (Figure 21). This safety circuit will not false trip from hot tap water. It
will only turn OFF the heater if the thermostat fails. To reset, press the button. If the high-limit trips frequently, please con-
tact us at www.jacuzzi.com, or at 1-800-288-4002.
PUSH TO RESET
OVER HEAT
PROTECTION
HEATER ON
High Limit
Reset
Heater
On
Fig. 21
IMPORTANT NOTE:
Heater will only work when
the water temp is 77°F or
above. You should always fill
the tub with warm water.
Fig. 18 Fig. 19
Controlling Whirlpool Direction & Flow
Controlling Waterfall (Applicable Models Only)
Turning the Waterfall Control knob
counter-clockwise will turn on the waterfall
Turning the Waterfall Control knob
clockwise will turn off the waterfall
Turning ON... Turning OFF...
The more the waterfall control knob is turned in a counter-
clockwise direction, the ow of water will increase. Reference
Figure 20.
The waterfall can only be activated when the whirlpool
pump is in operation.
Fig. 20
To remove accumulations of bathtub residue from the system, it is recommended that a bathtub be cleaned at least twice
a month. For best results, however, we recommend that you clean your bathtub after each use using Systems Clean™,
our exclusive two-part plumbing system cleaner made specically for bathtubs. Systems Clean™ is available through an
authorized Jacuzzi Luxury Bath distributor, by calling 1-800-288-4002 or may be purchased online at www.jacuzzi.com.
Operating Manual
English
www.jacuzzi.com Page 13
Cleaning
Systems Clean™
To remove accumulations of bathtub residue from the whirlpool system, it is recommended that a Whirlpool bathtub be
cleaned at least twice a month. For best results, we recommend that you clean your Whirlpool bathtub after each use us-
ing Systems Clean™, our exclusive two-part plumbing system cleaner made specically for Whirlpool bathtubs. Systems
Clean™ is available through an authorized Jacuzzi Luxury Bath distributor by calling us direct at 1-800-288-4002, or may
be purchased online at www.jacuzzi.com/baths.
Bathtub Additives
CAUTION: Do not use oil or oil-based bathtub additives. Never use abrasive or caustic household cleaners on any
Jacuzzi Luxury Bath product.
If you want to use any kind of bathtub additive, use only a small amount of low-foaming powder or crystal substance; the
whirlpool action intensies the foaming properties of soaps.
The use of certain bathtub oils, bubble baths, and bathtub additives may increase the level of accumulations of bathtub
residue in the Whirlpool system and may cause false reading of the water level sensors. If excess accumulations persist,
you should discontinue use of these products.
To remove accumulations of bathtub residue from the Whirlpool system, it is recommended that a bathtub be cleaned
regularly. For best results, we recommend that you clean your Whirlpool bathtub after each use using Systems Clean™,
our exclusive two-part plumbing system cleaner made specically for Whirlpool bathtubs. Systems Clean™ is available
through an authorized Jacuzzi Luxury Bath distributor, or by calling 1-800-288-4002 or may be purchased online at
www.jacuzzi.com.
To clean your bathtub, simply use a mild, non-abrasive liquid detergent solution. You can protect and restore the gloss to a
dulled acrylic surface by applying Meguiar’s #10 Mirror Glaze, a product specically designed for use on acrylic nishes. If
Meguiar’s is not available, use a ne grade automotive rubbing compound followed by an application of clear automotive
paste wax.
Minor scratches which do not penetrate the color nish can be removed by lightly sanding with 600-grit wet/dry sandpaper.
Restore the gloss using Meguiar’s Mirror Glaze or automotive paste wax. Major scratches and gouges which penetrate
the acrylic surface will require renishing. Call Jacuzzi Luxury Bath to nd a service agent in your area.
If hair, or other types of debris, get caught in the bearings of these jets, it could cause
them to stop spinning (Figure 22). This may require disassembly and removal. To do this,
simply grab the nozzle and pull it straight out of the jet housing. The bearing casing will be
attached to the nozzle. These two items can be separated by holding the casing and push-
ing the nozzle out from the rear of the casing. After the cleaning is complete, reassemble
and reinstall.
Maintenance
Spinning Jet Maintenance
Fig. 22
Operating Manual
English
Page 14 www.jacuzzi.com
Clean the suction cover/strainer of hair and debris when necessary (Figure 23).
1. Remove the center screw and detach the suction cover.
2. Clean the cover by back ushing debris from the holes.
3. Replace the suction cover immediately after cleaning.
WARNING! When reinstalling, orient the cover/strainer with the small
notch at the bottom. The gasket must be inserted into the groove of the
cover/strainer before reinstalling onto the suction tting.
DANGER: RISK OF SEVERE INJURY OR DROWNING! Keep hair a
minimum of 6 inches (152 mm) away from the suction tting at all times when the whirlpool system is operating. Hair
longer than shoulder length should be secured close to the head, or a bathing cap should be worn.
DANGER: RISK OF SEVERE INJURY OR DROWNING! Do not operate the Whirlpool system with the suction
cover/strainer removed! It is a safety device and must always be in place on the suction tting to minimize the potential
hazard of hair and body entrapment.
Maintenance (Continued)
Whirlpool Suction Cover/Strainer Maintenance
Fig. 23
Operating Manual
English
www.jacuzzi.com Page 15
Salon
®
Spa System Reference Illustrations
J4 Control Panel Salon
®
Spa Schematic Diagram
CONTROL
PANEL
CHROMATHERAPY
LIGHTS 2X
LEAD CONNECTIONS
4-WHITE-C
3-BLACK-H
2-N/A
1-GREEN-GRD
VIEW A
Air Valve
ILLUMATHERAPY
LIGHTS 4
SEE VIEW A
240VAC/20A
Dedicated GFCI
Required
AIR VALVE
ASSEMBLY
CONTROL BOX
240VAC
Pump
OR
Panel
Blower
LED Light
PUMP/MOTOR
120VAC 15A
Dedicated GFCI
Required
FUSE
FUSE
FUSE
FUSE
BLOWER
HEATER
FUSE/JUNCTION
BOX
AUTO-DRI™
SENSOR CABLES
CHROMATHERAPY
LIGHTS 2X
1
2
3
4
VIEW A
SEE VIEW A
PUMP/MOTOR
ILLUMATHERAPY
LIGHTS 4X
FUSE
FUSE
FUSE
FUSE
BLOWER
HEATER
CONTROL BOX
Air Valve
240VAC
Pump
RS232
Panel
Blower
Inside
Light 1
Inside
Light
3
Ambient
Light 1
Temp
Sensor
Inside
Light
2
Inside
Light
4
LOGO
Light
Ambient
Light
2
TEMPERATURE
SENSOR
OR
AUTO-DRI™ SENSOR CABLES
CONTROL
PANEL
240VAC/20A
Dedicated GFCI
Required
AIR VALVE
ASSEMBLY
LEAD CONNECTIONS
4-GREEN-(GRD)
3-RED-(L)
2-BLACK-(H)
1-WHITE-(C)
120VAC 15A
Dedicated GFCI
Required
FUSE/
JUNCTION BOX
Fig. 24
Fig. 25
J5 Control Panel Salon
®
Spa Schematic Diagram
Operating Manual
English
Page 16 www.jacuzzi.com
Salon
®
Spa Operations
J4 Salon
®
Spa Controls
Pure Air
®
and Auto-Dri™ Air Channels
For complete operating instructions reference page 5.
J5 Salon
®
Spa Controls
Controlling Whirlpool Direction and Flow
For complete operating instructions reference page 12.
Fig. 26
NOTE: When switching be-
tween functions, the LED for
the newly selected function
will FLASH once to indicate
selection.
WHIRLPOOL
• Press to turn ON
• Press again to turn OFF
• Use toggles to control
speed
INCREASE TOGGLE
• Press to increase selected
feature
• Press and hold 5 seconds to
set/cancel daily Auto-Dri™
• Press to increase light inten-
sity
• Press to turn ON lights at last
color used from OFF
DECREASE TOGGLE
• Press to decrease the
selected feature
• Press to decrease light
intensity all the way
down to OFF
LEFT AIR VALVE CONTROL
• Press to activate the left air
valve
• Use toggles to control air
mix
RIGHT AIR VALVE CONTROL
• Press to activate the right air
valve
• Use toggles to control air mix
WAVE FEATURE
• Press to turn Wave ON
• Press to turn Wave OFF
• +/- keys can be used to
adjust maximum inten-
sity.
CHROMATHERAPY
• Press once to turn lights
ON at white level 2
• Press again to cycle
colors
• Press again to stop at the
current color
• Press again to restart the
cycle
• Color Sequence: White,
Purple, Blue, Turquoise,
Green, Yellow, Orange,
Red, Pink, Repeat
STATUS LED
• Relays the current intensity of
selected feature
PURE AIR
®
FEATURE
• Press to turn ON
• Press again to turn OFF
• Use toggles to control
intensity
POWER
Main Menu
J5 Control Panel
Optional J5 Luxury LCD Control Panel: Operation instructions for this panel are
outlined in the supplemental guide provided in your warranty pack. Refer to this
document for complete operation details (P/N GU47000).
Operating Manual
English
www.jacuzzi.com Page 17
Troubleshooting Procedures
PROBLEM PROBABLE CAUSES REMEDY
Pump/motor does not start • No power to pump/motor
• Pump/motor not plugged in
• Pump/motor faulty
• Reset GFCI
• Insert plug securely into outlet
• Ensure control panel is connected to control box
• Contact Jacuzzi Luxury Bath @ 800-288-4002
Pump/motor operates but no fully
adjustable jets are functioning
• Jets are closed
• Suction cover/strainer may be clogged
• Open jets by rotating counter-clockwise
• With the motor turned OFF, remove the suction
cover/strainer and remove any debris. Replace the
suction cover before operating
Pump/motor operates but air is not
injected into the water
• Air valves are closed • Open air control valves
Water leakage from pump unions • Overtightened, O-ring may be pinched or improp-
erly seated, undertightened
• Loosen unions, check and reseat O-ring. If O-ring
has been pinched out of shape, replace (refer to
number below). When tightening union nuts, hand
tighten only
Pump/motor shuts off by itself before
time elapses
• Motor thermal protection has deactivated pump/
motor due to overheating (supply voltage low)
• GFCI tripped
• Inadequate supply wiring
• Let motor cool; thermal protection will reset. Check
for proper ventilation (check supply voltage)
• Reset GFCI; if it continues to trip, do not use this
unit. Disconnect the unit and have the problem cor-
rected by a licensed electrician before using
• Consult a licensed electrician to correct the wiring
unit
Chromatherapy lights do not operate • Connector has come loose • Contact Jacuzzi Luxury Bath @ 800-288-4002
Blower does not start • No power to pump/motor
• Blower not connected
• Blower faulty
• Reset GFCI and/or breaker
• Ensure plug is fully in outlet
• Ensure control panel is connected to control box
• Ensure control box is connected to control panel
• Contact Jacuzzi Luxury Bath @ 800-288-4002
Blower operates but NO air is exiting
the holes
• Check valves are stuck in the closed position • Contact Jacuzzi Luxury Bath @ 800-288-4002
Blower operates but air is not exiting
all of the holes
• Blower intensity is not sufcient
• Obstructed air holes
• Increase the blower intensity. NOTE: The system is
designed such that all air channels operate at the 4th
blower setting.
• Remove debris with a toothpick or tooth brush
Blower shuts off unexpectedly • 20 minute timer has elapsed
• GFCI tripped
• Inadequate supply wiring
• Improper ventilation
• Connector has come loose
• Turn on blower
• Reset GFCI; if it continues to trip, do not use the unit
• Consult a licensed electrician to correct
• Contact Jacuzzi Luxury Bath @ 800-288-4002
Drain assist Auto-Dri™ cycle comes
on multiple times
• Water sensors detect multiple wet and dry condi-
tions
• If during a Auto-Dri™ cycle, water is coming in
contact with both sensors, the system is working as
designed and will continue to Auto-Dri™ until excess
water is expelled
• Remove any washcloth or toy that may be covering
the sensors
Drain assist Auto-Dri™ does not
come on 5 minutes after bathtub is
drained out completely
• Water sensors not connected and not detecting
water being drained out of the tub
• Faulty control box
• Contact Jacuzzi Luxury Bath @ 800-288-4002
Water not maintaining temperature • High limit switch on heater has tripped • Press Reset button on heater
Waterfall not working • Whirlpool function not on
• Waterfall control knob is in the OFF position
• Debris in waterfall outlet
• Turn on whirlpool
• Turn waterfall control knob counter-clockwise until
water ow is at the desired ow
• Use a thin, rigid and non-abrasive material (ie. credit
card) and gently swipe back and forth until debris is
cleared away from the waterfall opening
If the unit is within the warranty period, contact Jacuzzi Luxury Bath Service Support at 1-800-288-4002 with your
bath’s serial number before work is started. The serial number is located on the Specication/Serial Number
Plate.
Operating Manual
English
Page 18 www.jacuzzi.com
Notes:
Jacuzzi Luxury Bath
14525 Avenue Monte Vista
Chino, CA 91710 États-Unis
1-800-288-4002
www.jacuzzi.com
Pure Air
MD
Baignoire d’hydromassage
Spa Salon
MD
MANUEL D’UTILISATION
LG74000D 06/2019
Manuel d’utilisation
Français
Page 2 www.jacuzzi.com
Renseignements généraux sur l’utilisation. ..................................................................................................................... 2
Illustration de référence d’un système Pure Air
MD
. ......................................................................................................... 3
Opérations de Pure Air
MD
. ............................................................................................................................................... 4
Canaux d’air Pure Air
MD
Auto-Dri
MC
. ................................................................................................................................ 5
Illustrations de référence du système de baignoire d’hydromassage. ......................................................................... 6-7
Opérations de la baignoire d’hydromassage. ............................................................................................................... 8-9
Schémas de référence du système de chauffage .................................................................................................... 10-11
RapidHeat
MC
. ................................................................................................................................................................. 12
Nettoyage. ..................................................................................................................................................................... 13
Entretien. .................................................................................................................................................................. 13-14
Illustrations de référence du système de spa Salon
MD
................................................................................................. 15
Opérations du spa Salon
MD
. ......................................................................................................................................... 16
Procédures de dépannage. ........................................................................................................................................... 17
*For Spanish and French installation instructions, please visit www.jacuzzi.com/baths/support/owners-manuals/.
*Para instrucciones de instalación en español, por favor visite www.jacuzzi.com/baths/support/owners-manuals/.
*Pour les directives d'installation en français canadien, veuillez visiter www.jacuzzi.com/baths/support/owners-manuals/.
Table des matières
Renseignements généraux sur l’utilisation
Toutes les baignoires fabriquées par Jacuzzi Luxury Bath sont conçues pour « remplissage et évacuation », ce qui signie
que la baignoire doit être vidée après chaque utilisation et remplie d’eau fraîche par le baigneur suivant. Il s’agit d’une
précaution de santé puisque ces baignoires ne sont pas conçues pour conserver de l’eau continuellement comme les
piscines ou les spas.
Fermez l’évacuation et remplissez la baignoire jusqu’à ce que l’eau soit à au moins 25 à 51 mm (1 à 2 po) au-dessus du
jet le plus élevé ou de l’entrée d’air (reportez-vous à la ligne d’eau indiquée dans l’illustration – Figure 1). Ne mettez pas
le système PureAir
MD
de la baignoire d’hydromassage en marche si les jets ou commandes d’air ne sont pas complète-
ment immergés dans l’eau. Faire fonctionner la baignoire d’hydromassage ou le système PureAir
MD
lorsqu’il n’y a pas
assez d’eau peut entraîner la pulvérisation de l’eau à l’extérieur de la baignoire.
ATTENTION : lorsque vous sortez de la baignoire, le niveau
d’eau s’abaissera sous les jets ce qui pourrait entraîner la
pulvérisation de l’eau à l’extérieur de la baignoire. Pour empêcher
cette pulvérisation, vous devez éteindre l’unité avant de sortir de
la baignoire.
Remplir jusqu’à une
distance d’au moins
2,5 à 5 cm au-dessus
du jet le plus élevé
Fig. 1
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54

Jacuzzi MOF6636WCR2CPWC Manuel utilisateur

MOF6636WCR2CPWC
Jacuzzi
Marque
Jacuzzi
Modèle
MOF6636WCR2CPWC
Catégorie
Chauffe-eau
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents