Sony MEX-GS620BT Manuel utilisateur

Marque: Sony

Modèle: MEX-GS620BT

Catégorie: Récepteurs multimédia de voiture

Taper: Manuel utilisateur

MEX-GS620BT

4-687-334-11(1)

Bluetooth®

Audio System

Owner’s Record

The model and serial numbers are located on the bottom of the

unit.

Record the serial number in the space provided below.

Refer to these numbers whenever you call upon your Sony dealer

regarding this product.

Model No. MEX-GS620BT

Serial No.

Operating Instructions

Mode d’emploi

To cancel the demonstration (DEMO) display, see page 19.

For the connection/installation, see page 32.

Pour annuler l’affichage de démonstration (DEMO),

reportez-vous à la page 21.

Pour le raccordement/l’installation, reportez-vous à la page 36.

2GB

The nameplate indicating operating voltage, etc., is

located on the bottom of the chassis.

Warning

This device complies with Part 15 of the FCC Rules

and Industry Canada’s licence-exempt RSSs.

Operation is subject to the following two

conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference,

including interference that may cause undesired

operation of the device.

This transmitter must not be co-located or operated

in conjunction with any other antenna or

transmitter.

Under Industry Canada regulations, this radio

transmitter may only operate using an antenna of a

type and maximum (or lesser) gain approved for

the transmitter by Industry Canada. To reduce

potential radio interference to other users, the

antenna type and its gain should be so chosen that

the equivalent isotropically radiated power (e.i.r.p.)

is not more than that necessary for successful

communication.

This equipment complies with FCC/IC radiation

exposure limits set forth for an uncontrolled

environment and meets the FCC radio frequency

(RF) Exposure Guidelines and RSS-102 of the IC

radio frequency (RF) Exposure rules. This

equipment has very low levels of RF energy that is

deemed to comply without maximum permissive

exposure evaluation (MPE).

CAUTION

The use of optical instruments with this product will

increase eye hazard.

For the State of California, USA only

Perchlorate Material – special handling may apply,

See

www.dtsc.ca.gov/hazardouswaste/perchlorate

WARNING: Do not ingest battery,

Chemical Burn Hazard.

The remote commander contains a coin/

button cell battery. If the coin/button cell battery is

swallowed, it can cause severe internal burns in just

2 hours and can lead to death.

Keep new and used batteries away from children. If

the battery compartment does not close securely,

stop using the product and keep it away from

children.

If you think batteries might have been swallowed or

placed inside any part of the body, seek immediate

medical attention.

Note on the lithium battery

Do not expose the battery to excessive heat such as

direct sunlight, fire or the like.

For safety, be sure to install this unit in the

dashboard of the car as the rear side of the unit

becomes hot during use.

For details, see “Connection/Installation”

(page 32).

FOR THE CUSTOMERS IN THE USA. NOT

APPLICABLE IN CANADA, INCLUDING IN THE

PROVINCE OF QUEBEC.

POUR LES CLIENTS AUX ÉTATS-UNIS. NON

APPLICABLE AU CANADA, Y COMPRIS LA

PROVINCE DE QUÉBEC.

This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable

protection against harmful interference in a

residential installation. This equipment

generates, uses, and can radiate radio frequency

energy and, if not installed and used in

accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference to

radio or television reception, which can be

determined by turning the equipment off and

on, the user is encouraged to try to correct the

interference by one or more of the following

measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the

equipment and receiver.

 Connect the equipment into an outlet on a

circuit different from that to which the receiver

is connected.

 Consult the dealer or an experienced radio/TV

technician for help.

You are cautioned that any changes or

modifications not expressly approved in this

manual could void your authority to operate this

equipment.

3GB

Disclaimer regarding services offered by third

parties

Services offered by third parties may be changed,

suspended, or terminated without prior notice.

Sony does not bear any responsibility in these sorts

of situations.

Caution

IN NO EVENT SHALL SONY BE LIABLE FOR ANY

INCIDENTAL, INDIRECT OR CONSEQUENTIAL

DAMAGES OR OTHER DAMAGES INCLUDING,

WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF

REVENUE, LOSS OF DATA, LOSS OF USE OF THE

PRODUCT OR ANY ASSOCIATED EQUIPMENT,

DOWNTIME, AND PURCHASER’S TIME RELATED TO

OR ARISING OUT OF THE USE OF THIS PRODUCT, ITS

HARDWARE AND/OR ITS SOFTWARE.

Dear customer, this product includes a radio

transmitter.

Please check your vehicle operation manual or

contact the manufacturer of your vehicle or your

vehicle dealer, before you install this product into

your vehicle.

Emergency calls

This BLUETOOTH car handsfree and the electronic

device connected to the handsfree operate using

radio signals, cellular, and landline networks as well

as user-programmed function, which cannot

guarantee connection under all conditions.

Therefore do not rely solely upon any electronic

device for essential communications (such as

medical emergencies).

On BLUETOOTH communication

 Microwaves emitting from a BLUETOOTH device

may affect the operation of electronic medical

devices. Turn off this unit and other BLUETOOTH

devices in the following locations, as it may cause

an accident.

 where inflammable gas is present, in a hospital,

train, airplane, or petrol station

 near automatic doors or a fire alarm

 This unit supports security capabilities that

comply with the BLUETOOTH standard to provide

a secure connection when the BLUETOOTH

wireless technology is used, but security may not

be enough depending on the setting. Be careful

when communicating using BLUETOOTH wireless

technology.

 We do not take any responsibility for the leakage

of information during BLUETOOTH

communication.

If you have any questions or problems concerning

your unit that are not covered in this manual,

consult your nearest Sony dealer.

Warning if your car’s ignition has no ACC

position

Be sure to set the AUTO OFF function (page 19).

The unit will shut off completely and

automatically in the set time after the unit is

turned off, which prevents battery drain. If you

do not set the AUTO OFF function, press and hold

OFF until the display disappears each time you

turn the ignition off.

Important notice

4GB

Table of Contents

Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Guide to Parts and Controls . . . . . . . . . . . . . . . . . . . 5

Getting Started

Detaching the Front Panel . . . . . . . . . . . . . . . . . . . . 7

Resetting the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Preparing a BLUETOOTH Device. . . . . . . . . . . . . . . . 8

Connecting a USB Device . . . . . . . . . . . . . . . . . . . . 10

Connecting Other Portable Audio Device . . . . . . . 10

Listening to the Radio

Listening to the Radio. . . . . . . . . . . . . . . . . . . . . . . 10

Using Radio Data System (RDS) . . . . . . . . . . . . . . . 11

Listening to the SiriusXM Radio . . . . . . . . . . . . . . . 11

Playback

Playing a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Playing a USB Device . . . . . . . . . . . . . . . . . . . . . . . 12

Playing a BLUETOOTH Device. . . . . . . . . . . . . . . . . 13

Searching and Playing Tracks. . . . . . . . . . . . . . . . . 13

Listening to Pandora®

Setting up Pandora® . . . . . . . . . . . . . . . . . . . . . . . . 14

Streaming Pandora® . . . . . . . . . . . . . . . . . . . . . . . . 14

Available Operations in Pandora® . . . . . . . . . . . . . 15

Handsfree Calling (via BLUETOOTH

only)

Receiving a Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Making a Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Available Operations during Call . . . . . . . . . . . . . . 16

Useful Functions

SongPal with iPhone/Android smartphone . . . . . 17

Using Siri Eyes Free . . . . . . . . . . . . . . . . . . . . . . . . . 18

Settings

Canceling the DEMO Mode . . . . . . . . . . . . . . . . . . 19

Basic Setting Operation . . . . . . . . . . . . . . . . . . . . . 19

General Setup (GENERAL). . . . . . . . . . . . . . . . . . . . 19

Sound Setup (SOUND) . . . . . . . . . . . . . . . . . . . . . . 20

Display Setup (DISPLAY) . . . . . . . . . . . . . . . . . . . . . 21

BLUETOOTH Setup (BLUETOOTH). . . . . . . . . . . . . . 22

SongPal Setup (SONGPAL) . . . . . . . . . . . . . . . . . . . 22

Additional Information

Updating the Firmware . . . . . . . . . . . . . . . . . . . . . 23

Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Connection/Installation

Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Parts List for Installation . . . . . . . . . . . . . . . . . . . . 32

Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

5GB

Guide to Parts and Controls

Front panel removed (inner panel)

The number 3/ (repeat) button has a tactile dot.

 (browse) (page 11, 13, 14, 15)

Enter the browse mode during playback.

(Not available when an iPod is connected.)

 Front panel release button

 SEEK +/–

Tune in radio stations automatically. Press and

hold to tune manually.

/ (prev/next)

/ (fast-reverse/fast-forward)

 Control dial

Rotate to adjust the volume.

PUSH ENTER

Enter the selected item.

Press SRC, rotate then press to change the

source (timeout in 2 seconds).

VOICE (page 16, 18)

Activate voice dial, voice recognition (Android™

smartphone only), or the Siri function (iPhone

only).

APP (page 17)

Press and hold for more than 2 seconds to

establish “SongPal” function (connection).

N-Mark

Touch the control dial with Android smartphone

to make BLUETOOTH connection.

 Receptor for the remote commander

 Disc slot

 Display window

 (disc eject)

 SRC (source)

Turn on the power.

Change the source.

OFF

Press and hold for 1 second to turn the source

off and display the clock.

Press and hold for more than 2 seconds to turn

off the power and the display.

If the unit is turned off and the display

disappears, operation by the remote

commander is not available.

 (back)

Return to the previous display.

MODE (page 10, 11, 15, 16)

 CALL

Enter the call menu. Receive/end a call.

Press and hold more than 2 seconds to switch

the BLUETOOTH signal.

 MENU

Open the setup menu.

DSPL (display)

Press and hold, then press to change display

items.

Main unit

6GB

 Number buttons (1 to 6)

Receive stored radio stations. Press and hold to

store stations.

ALBUM /

Skip an album for audio device. Press and hold

to skip albums continuously.

(Not available when an iPod is connected.)

Press  to thumbs up, or  to thumbs down in

Pandora® (page 15).

(repeat)

(shuffle)

MIC (page 16)

PAUSE

 PTY (program type)

Select PTY in RDS.

CAT (category)

Select radio channels from categories in

SiriusXM.

 AUX input jack

 USB port

 RESET (inner panel) (page 7)

The VOL (volume) + button has a tactile dot.

 SOUND

Open the SOUND menu directly.

Press and hold to open the setup menu.

///

Select a setup item, etc.

ENTER

Enter the selected item.

Press and hold for more than 2 seconds to

establish or terminate the “SongPal” function.

/ (prev/next)

+/– (album +/–)

 DSPL (display)

Change display items.

SCRL (scroll)

Press and hold to scroll a display item.

 VOL (volume) +/–

Remove the insulation film before use.

RM-X231 Remote commander

7GB

Detaching the Front Panel

You can detach the front panel of this unit to

prevent theft.

1 Press and hold OFF  until the unit turns

off, press the front panel release button

, then pull the panel towards you to

remove.

Caution alarm

If you turn the ignition switch to the OFF position

without detaching the front panel, the caution

alarm will sound for a few seconds. The alarm will

only sound if the built-in amplifier is used.

Serial numbers

Make sure the serial numbers on the bottom of the

unit and the back of the front panel are matched

correctly. Otherwise you cannot make BLUETOOTH

pairing, connection and disconnection by NFC.

Resetting the Unit

Before operating the unit for the first time, after

replacing the car battery, or changing the

connections, you must reset the unit.

Press RESET on the inner panel with a ball-point

pen, etc., after detaching the front panel.

Note

Resetting the unit will erase the clock setting and some

stored contents.

Setting the Clock

1 Press MENU, rotate the control dial to

select [GENERAL], then press it.

2 Rotate the control dial to select [SET

CLOCK-ADJ], then press it.

The hour indication flashes.

3 Rotate the control dial to set the hour

and minute.

To move the digital indication, press SEEK +/–.

4 After setting the minute, press MENU.

The setup is complete and the clock starts.

To display the clock

Press and hold DSPL.

Getting Started

Attaching the front panel

8GB

Preparing a BLUETOOTH Device

You can enjoy music, or perform handsfree calling

depending on the BLUETOOTH compatible device

such as a smartphone, cellular phone and audio

device (hereafter “BLUETOOTH device” if not

otherwise specified). For details on connecting,

refer to the operating instructions supplied with the

device.

Before connecting the device, turn down the

volume of this unit; otherwise, loud sound may

result.

By touching the control dial on the unit with an

NFC* compatible smartphone, the unit is paired and

connected with the smartphone automatically.

* NFC (Near Field Communication) is a technology

enabling short-range wireless communication

between various devices, such as mobile phones and

IC tags. Thanks to the NFC function, data

communication can be achieved easily just by

touching the relevant symbol or designated location

on NFC compatible devices.

For a smartphone with Android OS 4.0 or lower

installed, downloading the app “NFC Easy Connect”

available at Google Play™ is required. The app may

not be downloadable in some countries/regions.

1 Activate the NFC function on the

smartphone.

For details, refer to the operating instructions

supplied with the smartphone.

2 Touch the N-Mark part of the unit with

the N-Mark part of the smartphone.

Make sure that lights up on the display of the

unit.

To disconnect by One touch

Touch the N-Mark part of the unit with the N-Mark

part of the smartphone again.

Notes

 When making the connection, handle the

smartphone carefully to prevent scratches.

 One touch connection is not possible when the unit is

already connected to two NFC compatible devices. In

this case, disconnect either device, and make

connection with the smartphone again.

When connecting a BLUETOOTH device for the first

time, mutual registration (called “pairing”) is

required. Pairing enables this unit and other devices

to recognize each other. This unit can connect two

BLUETOOTH devices (two cellular phones, or a

cellular phone and an audio device).

1 Place the BLUETOOTH device within 1 m

(3 ft) of this unit.

2 Press MENU, rotate the control dial to

select [BLUETOOTH], then press it.

3 Rotate the control dial to select [SET

PAIRING], then press it.

4 Rotate the control dial to select [SET

DEVICE 1]* or [SET DEVICE 2]*, then press

it.

flashes while the unit is in pairing standby

mode.

* [SET DEVICE 1] or [SET DEVICE 2] will be changed

to the paired device name after pairing is

complete.

5 Perform pairing on the BLUETOOTH

device so it detects this unit.

6 Select [MEX-GS620BT] shown in the

display of the BLUETOOTH device.

If your model name does not appear, repeat

from step 2.

7 If passkey* input is required on the

BLUETOOTH device, input [0000].

* Passkey may be called “Passcode,” “PIN code,”

“PIN number” or “Password,” etc., depending on

the device.

When pairing is made, stays lit.

Connecting with a Smartphone by One

touch (NFC)

Pairing and connecting with a

BLUETOOTH device

[0000]

Input passkey

9GB

8 Select this unit on the BLUETOOTH device

to establish the BLUETOOTH connection.

or lights up when the connection is made.

Note

While connecting to a BLUETOOTH device, this unit

cannot be detected from another device. To enable

detection, enter the pairing mode and search for this

unit from another device.

To start playback

For details, see “Playing a BLUETOOTH Device”

(page 13).

To disconnect the paired device

Perform steps 2 to 4 to disconnect after this unit

and the BLUETOOTH device are paired.

To use a paired device, connection with this unit is

required. Some paired devices will connect

automatically.

1 Press MENU, rotate the control dial to

select [BLUETOOTH], then press it.

2 Rotate the control dial to select [SET BT

SIGNL], then press it.

Make sure that lights up.

3 Activate the BLUETOOTH function on the

BLUETOOTH device.

4 Operate the BLUETOOTH device to

connect to this unit.

or lights up.

Icons in the display:

To connect the last-connected device from

this unit

Activate the BLUETOOTH function on the

BLUETOOTH device.

To connect with the audio device, press SRC to

select [BT AUDIO] and press PAUSE.

To connect with the cellular phone, press CALL.

Note

While streaming BLUETOOTH audio, you cannot

connect from this unit to the cellular phone. Connect

from the cellular phone to this unit instead.

Tip

With BLUETOOTH signal on: when the ignition is turned

to on, this unit reconnects automatically to the last-

connected cellular phone.

To install the microphone

For details, see “Installing the microphone”

(page 34).

When an iPhone/iPod with iOS5 or later installed is

connected to the USB port, the unit is paired and

connected with the iPhone/iPod automatically.

To enable BLUETOOTH Auto Pairing, make sure [SET

AUTOPAIR] in [BLUETOOTH] is set to [ON] (page 22).

1 Activate the BLUETOOTH function on the

iPhone/iPod.

2 Connect an iPhone/iPod to the USB port.

Make sure that lights up on the display of the

unit.

Notes

 BLUETOOTH Auto Pairing is not possible if the unit is

already connected to two BLUETOOTH devices. In this

case, disconnect the either device, then connect the

iPhone/iPod again.

 If BLUETOOTH Auto Pairing is not established, see

“Preparing a BLUETOOTH Device” for details (page 8).

Connecting with a paired BLUETOOTH

device

Lights up when handsfree calling is

available by enabling the HFP (Handsfree

Profile).

Lights up when the audio device is

playable by enabling the A2DP

(Advanced Audio Distribution Profile).

Connecting with an iPhone/iPod

(BLUETOOTH Auto Pairing)

10GB

Connecting a USB Device

1 Turn down the volume on the unit.

2 Connect the USB device to the unit.

To connect an iPod/iPhone, use the USB

connection cable for iPod (not supplied).

Connecting Other Portable

Audio Device

1 Turn off the portable audio device.

2 Turn down the volume on the unit.

3 Connect the portable audio device to the

AUX input jack (stereo mini jack) on the

unit with a connecting cord (not

supplied)*.

* Be sure to use a straight type plug.

4 Press SRC to select [AUX].

To match the volume level of the connected

device to other sources

Start playback of the portable audio device at a

moderate volume, and set your usual listening

volume on the unit.

Press MENU, then select [SOUND]  [SET AUX VOL]

(page 21).

Listening to the Radio

To listen to the radio, press SRC to select [TUNER].

1 Press MODE to change the band (FM1,

FM2, FM3, AM1 or AM2).

2 Press MENU, rotate the control dial to

select [GENERAL], then press it.

3 Rotate the control dial to select [SET

BTM], then press it.

The unit stores stations in order of frequency on

the number buttons.

1 Press MODE to change the band (FM1,

FM2, FM3, AM1 or AM2).

2 Perform tuning.

To tune manually

Press and hold SEEK +/– to locate the

approximate frequency, then press SEEK +/–

repeatedly to fine adjust to the desired

frequency.

To tune automatically

Press SEEK +/–.

Scanning stops when the unit receives a station.

1 While receiving the station that you want

to store, press and hold a number button

(1 to 6) until [MEM] appears.

1 Select the band, then press a number

button (1 to 6).

Listening to the Radio

Storing automatically (BTM)

Tuning

Storing manually

Receiving the stored stations

11GB

Using Radio Data System (RDS)

1 Press PTY during FM reception.

2 Rotate the control dial until the desired

program type appears, then press it.

The unit starts to search for a station

broadcasting the selected program type.

Type of programs

The CT data from the RDS transmission sets the

clock.

1 Set [SET CT-ON] in [GENERAL] (page 20).

Listening to the SiriusXM Radio

Only SiriusXM brings you more of what you love to

listen to, all in one place. Get over 140 channels,

including commercial-free music plus the best

sports, news, talk, comedy and entertainment.

Welcome to the world of satellite radio. A SiriusXM

Connect Vehicle Tuner and Subscription are

required. For more information, visit

www.siriusxm.com

After installing your SiriusXM Connect Vehicle Tuner

and antenna, press SRC to select [SIRIUSXM]. You

should be able to hear the SiriusXM preview

channel on Channel 1. After verifying that you can

hear the preview channel, select Channel 0 to find

the Radio ID of your tuner. In addition, the Radio ID

is located on the bottom of the SiriusXM Connect

Vehicle Tuner and its packaging. You will need this

number to activate your subscription. Write the

number down for reference.

In the USA, you can activate online or by calling

SiriusXM Listener Care:

 Online: Visit www.siriusxm.com/activatenow

 Phone: Call 1-866-635-2349

In Canada, you can activate online or by calling

SiriusXM Listener Care:

 Online: Visit www.siriusxm.ca/activatexm

 Phone: Call 1-877-438-9677

As part of the activation process, the SiriusXM

satellites will send an activation message to your

tuner. When your radio detects that the tuner has

received the activation message, your radio will

display: [SUBSCRIPTION UPDATED - PRESS ENT TO

CONTINUE]. Once subscribed, you can tune to

channels in your subscription plan.

Notes

 The activation process usually takes 10 to 15 minutes,

but may take up to an hour.

 Your radio will need to be turned on and receiving the

SiriusXM signal to receive the activation message.

1 Press (browse).

2 Rotate the control dial to select the

desired channel, then press it.

To select channels from categories

1 Press CAT.

2 Rotate control dial to select the desired category,

then press it.

3 Rotate the control dial to select the desired

channel, then press it.

To store channels

1 While receiving the channel that you want to store,

press and hold a number button (1 to 6) until [MEM]

appears.

To receive the stored channel, press MODE to select

[SX1], [SX2] or [SX3], then press a number button (1

to 6).

Selecting program types (PTY)

NEWS (News), INFORM (Information), SPORTS

(Sports), TALK (Talk), ROCK (Rock), CLS ROCK

(Classic Rock), ADLT HIT (Adult Hits), SOFT RCK (Soft

Rock), TOP 40 (Top 40), COUNTRY (Country),

OLDIES (Oldies), SOFT (Soft), NOSTALGA

(Nostalgia), JAZZ (Jazz), CLASSICL (Classical),

R & B (Rhythm and Blues), SOFT R&B (Soft Rhythm

and Blues), LANGUAGE (Foreign Language), REL

MUSC (Religious Music), REL TALK (Religious Talk),

PERSNLTY (Personality), PUBLIC (Public), COLLEGE

(College), HABL ESP (Spanish Talk), MUSC ESP

(Spanish Music), HIP HOP (Hip-Hop), WEATHER

(Weather)

Setting clock time (CT)

Activating your SiriusXM Subscription

Selecting channels for SiriusXM

12GB

To set a parental control

The parental control feature allows you to limit

access to SiriusXM channels with mature content.

When enabled, the parental control feature requires

you to enter a passcode to tune to the locked

channels. Information on setting up the passcode

and locking channels can be found below.

1 Press MENU and rotate the control dial.

2 Select [GENERAL]  [SXM PARENTAL] 

[LOCK SELECT]  [LOCK-ON].

3 Enter the passcode by rotating the control dial on

the unit or pressing / on the remote

commander.

To move the entry position, press SEEK +/– on the

unit or / on the remote commander.

The initial passcode is [0000].

4 After entering the passcode, press ENTER.

To unlock the channels, select [LOCK-OFF].

To change the passcode

1 Press MENU and rotate the control dial.

2 Select [GENERAL]  [SXM PARENTAL]  [CODE EDIT].

3 Enter the current passcode on the current passcode

input display, then press ENTER.

The initial passcode is [0000].

4 Enter your new 4-digit passcode on the new

passcode input display, then press ENTER.

To change display items

Press and hold DSPL, then press DSPL again to

change as follows:

Channel Number (Default)  Channel Name  Artist

Name  Song Title  Content Info  Category Name

 Clock

Playing a Disc

1 Insert the disc (label side up).

Playback starts automatically.

Playing a USB Device

In these Operating Instructions, “iPod” is used as a

general reference for the iPod functions on an iPod

and iPhone, unless otherwise specified by the text

or illustrations.

For details on the compatibility of your iPod, see

“About iPod” (page 23) or visit the support site on

the back cover.

MSC (Mass Storage Class) and MTP (Media Transfer

Protocol) type USB devices* compliant with the USB

standard can be used. Some digital media players

or Android smartphones may require setting to

MTP mode.

* e.g., a USB flash drive, digital media player, Android

smartphone

Notes

 For details on the compatibility of your USB device,

visit the support site on the back cover.

 Playback of the following files is not supported.

MP3/WMA/AAC/FLAC:

 copyright-protected files

 DRM (Digital Rights Management) files

 Multi-channel audio files

MP3/WMA/AAC:

 lossless compression files

WAV:

 Multi-channel audio files

1 Connect a USB device to the USB port

(page 10).

Playback starts.

If a device is already connected, to start

playback, press SRC to select [USB1] for the USB

port on the front, [USB2] for the USB port on the

rear ([IPD] appears in the display when the iPod

is recognized).

2 Adjust the volume on this unit.

Playback

13GB

To stop playback

Press and hold OFF for 1 second.

To remove the device

Stop playback, then remove the device.

Caution for iPhone

When you connect an iPhone via USB, phone call

volume is controlled by the iPhone, not the unit. Do

not inadvertently increase the volume on the unit

during a call, as a sudden loud sound may result

when the call ends.

Playing a BLUETOOTH Device

You can play contents on a connected device that

supports BLUETOOTH A2DP (Advanced Audio

Distribution Profile).

1 Make BLUETOOTH connection with the

audio device (page 8).

To select the audio device, press MENU, then

select [BLUETOOTH]  [SET AUDIODEV]

(page 22).

2 Press SRC to select [BT AUDIO].

3 Operate the audio device to start

playback.

4 Adjust the volume on this unit.

Notes

 Depending on the audio device, information such as

title, track number/time and playback status may not

be displayed on this unit.

 Even if the source is changed on this unit, playback of

the audio device does not stop.

 [BT AUDIO] does not appear in the display while

running the “SongPal” application via the BLUETOOTH

function.

To match the volume level of the BLUETOOTH

device to other sources

Start playback of the BLUETOOTH audio device at a

moderate volume, and set your usual listening

volume on the unit.

Press MENU, then select [SOUND]  [SET BTA VOL]

(page 21).

Searching and Playing Tracks

1 During playback, press (repeat) or

(shuffle) repeatedly to select the desired

play mode.

Playback in the selected play mode may take

time to start.

Available play modes differ depending on the

selected sound source.

Not available when an iPod is connected.

1 During CD, USB or BT AUDIO*

playback,

press (browse)*

to display the list of

search categories.

When the track list appears, press (back)

repeatedly to display the desired search

category.

*1 Available only for audio devices supporting

AVRCP (Audio Video Remote Control Profile) 1.4

or above.

*2 During USB playback, press (browse) for

more than 2 seconds to directly return to the

beginning of the category list.

2 Rotate the control dial to select the

desired search category, then press it to

confirm.

3 Repeat step 2 to search the desired track.

Playback starts.

To exit the Quick-BrowZer mode

Press (browse).

Repeat play and shuffle play

Searching a track by name (Quick-

BrowZer™)

14GB

Not available when an iPod is connected.

1 Press (browse).

2 Press SEEK +.

3 Rotate the control dial to select the item.

The list is jumped in steps of 10% of the total

number of items.

4 Press ENTER to return to the Quick-

BrowZer mode.

The selected item appears.

5 Rotate the control dial to select the

desired item, then press it.

Playback starts.

Pandora® is available to stream music through your

iPhone and Android smartphone. You can control

Pandora® on a BLUETOOTH connected iPhone/

Android smartphone from this unit.

Pandora® is only available in certain countries.

Please visit

http://www.pandora.com/legal

for more information.

Setting up Pandora®

1 Check the compatibility of your mobile

device by visiting the support site on the

back cover.

2 Download the latest version of the

Pandora® application from your

smartphone’s app store. A list of

compatible devices can be found at

www.pandora.com/everywhere/mobile

Streaming Pandora®

1 Connect the mobile device with this unit

(page 8).

To select the audio device, press MENU, then

select [BLUETOOTH]  [SET AUDIODEV]

(page 22).

2 Press SRC to select [PANDORA].

3 Launch Pandora® application on your

mobile device.

4 Press PAUSE to start playback.

If the device number appears

Make sure that the same numbers are displayed

(e.g., 123456) in this unit and the mobile device,

then press ENTER on this unit and select [Yes] on

the mobile device.

When activating the BLUETOOTH function

You can adjust the volume level.

Press MENU, then select [SOUND]  [SET BTA VOL]

(page 21).

Searching by skipping items

(Jump mode)

Listening to Pandora®

15GB

Available Operations in

Pandora®

“Thumbs Up” or “Thumbs Down” feedback allows

you to personalize stations.

1 During playback, press  (Thumbs Up) or

 (Thumbs Down).

The station list allows you to easily select a desired

station.

1 During playback, press (browse).

2 Press SEEK + to select the sorting order

[BY DATE] or [A TO Z].

3 Rotate the control dial to select the

desired station, then press it.

Playback starts.

The track currently being played can be

bookmarked and stored in your Pandora® account.

1 During playback, press MODE.

To use a cellular phone, connect it with this unit.

You can connect two cellular phones to the unit. For

details, see “Preparing a BLUETOOTH Device”

(page 8).

Receiving a Call

1 Press CALL when a call is received with a

ringtone.

The phone call starts.

Note

The ringtone and talker’s voice are output only from the

front speakers.

To reject the call

Press and hold OFF for 1 second.

To end the call

Press CALL again.

Making a Call

You can make a call from the phonebook or call

history when a cellular phone supporting PBAP

(Phone Book Access Profile) is connected.

When two cellular phones are connected to the

unit, select either phone.

1 Press CALL.

When two cellular phones are connected to the

unit, rotate the control dial to select either

phone, then press it.

2 Rotate the control dial to select [PHONE

BOOK], then press it.

3 Rotate the control dial to select an initial

from the initial list, then press it.

4 Rotate the control dial to select a name

from the name list, then press it.

“Thumbs” feedback

Using the station list

Bookmarking

Handsfree Calling (via BLUETOOTH

only)

From the phonebook

16GB

5 Rotate the control dial to select a

number from the number list, then press

it.

The phone call starts.

1 Press CALL.

When two cellular phones are connected to the

unit, rotate the control dial to select either

phone, then press it.

2 Rotate the control dial to select [RECENT

CALL], then press it.

A list of the call history appears.

3 Rotate the control dial to select a name

or phone number from the call history,

then press it.

The phone call starts.

1 Press CALL.

When two cellular phones are connected to the

unit, rotate the control dial to select either

phone, then press it.

2 Rotate the control dial to select [DIAL

NUMBER], then press it.

3 Rotate the control dial to enter the

phone number, and lastly select [ ]

(space), then press ENTER*.

The phone call starts.

* To move the digital indication, press SEEK +/–.

Note

[_] appears instead of [#] on the display.

1 Press CALL.

When two cellular phones are connected to the

unit, rotate the control dial to select either

phone, then press it.

2 Rotate the control dial to select [REDIAL],

then press it.

The phone call starts.

You can make a call by saying the voice tag stored

in a connected cellular phone that has a voice

dialing function.

1 Press CALL.

When two cellular phones are connected to the

unit, rotate the control dial to select either

phone, then press it.

2 Rotate the control dial to select [VOICE

DIAL], then press it.

Alternatively, press VOICE while the “SongPal”

function is off.

3 Say the voice tag stored on the cellular

phone.

Your voice is recognized, and the call is made.

To cancel voice dialing

Press VOICE.

Available Operations during

Call

To adjust the ringtone volume

Rotate the control dial while receiving a call.

To adjust the talker’s voice volume

Rotate the control dial during a call.

To adjust the volume for the other party (Mic

gain adjustment)

Press MIC.

Adjustable volume levels: [MIC-LOW], [MIC-MID],

[MIC-HI].

To reduce echo and noise (Echo Canceler/

Noise Canceler Mode)

Press and hold MIC.

Settable mode: [EC/NC-1], [EC/NC-2].

To switch between handsfree mode and

handheld mode

During a call, press MODE to switch the phone call

audio between the unit and cellular phone.

Note

Depending on the cellular phone, this operation may

not be available.

From the call history

By phone number input

By redial

By voice tags

17GB

SongPal with iPhone/Android

smartphone

Downloading the latest version

of “SongPal” application is

required from the App Store for

iPhone or from Google Play for

Android smartphone.

Notes

 For your safety, follow your local

traffic laws and regulations, and

do not operate the application

while driving.

 “SongPal” is an app for

controlling Sony audio devices

which are compatible with “SongPal”, by your iPhone/

Android smartphone.

 What you can control with “SongPal” varies

depending on the connected device.

 To make use of “SongPal” features, see the details on

your iPhone/Android smartphone.

 For further details on “SongPal,” visit the following

URL: http://rd1.sony.net/help/speaker/songpal/

 Visit the website below and check the compatible

iPhone/Android smartphone models.

For iPhone: visit the App Store

For Android smartphone: visit Google Play

1 Make the BLUETOOTH connection with

iPhone/Android smartphone (page 8).

To select the audio device, press MENU, then

select [BLUETOOTH]  [SET AUDIODEV]

(page 22).

2 Launch the “SongPal” application.*

3 Press and hold APP on the unit for more

than 2 seconds.*

Connection to iPhone/Android smartphone

starts.

For details on the operations on iPhone/

Android smartphone, see the help of the

application.

*1 If [AUTO LAUNCH] in [SONGPAL] is set to [ON]

(page 22), the “SongPal” connection is

established automagically when the BLUETOOTH

signal of iPhone/Android smartphone is turned

on.

*2 Alternatively, press MENU, then select [SONGPAL]

 [CONNECT] (page 22).

If the device number appears

Make sure that the number is displayed (e.g.,

123456), then select [Yes] on the iPhone/Android

smartphone.

To terminate connection

1 Press MENU, rotate the control dial to select

[SONGPAL], then press it.

2 Rotate the control dial to select [CONNECT], then

press it.

Selecting the source or application

You can operate to select the desired source or

application on iPhone/Android smartphone.

To select the source

Press SRC repeatedly. Alternatively, press SRC,

rotate the control dial to select the desired source,

then press ENTER.

To display the source list

Press SRC.

Announcement of various information by

voice guide (Android smartphone only)

When SMS, Twitter/Facebook/Calendar

notifications, etc., are received, they are

automatically announced through the car speakers.

For details on settings, refer to the help of the

application.

Useful Functions

Establishing the SongPal connection

18GB

Activating voice recognition (Android

smartphone only)

By registering applications, you can control an

application by voice command. For details, refer to

the help of the application.

To activate voice recognition

1 Press VOICE to activate voice recognition.

2 Say the desired voice command into the

microphone when [Say Source or App] appears on

the Android smartphone.

Notes

 Voice recognition may not be available in some cases.

 Voice recognition may not work properly depending

on the performance of the connected Android

smartphone.

 Operate under conditions where noise such as engine

sound is minimized during voice recognition.

Replying a message of SMS (Android

smartphone only)

You can reply a message by voice recognition.

1 Activate voice recognition, then input “Reply.”

The message input display appears on the “SongPal”

application.

2 Input a reply message by voice recognition.

The list of message candidates appears on the

“SongPal” application.

3 Rotate the control dial to select the desired

message, then press it.

The message is sent out.

Making sound and display settings

You can adjust the settings relating to sound and

display via iPhone/Android smartphone.

For details on settings, refer to the help of the

application.

Using Siri Eyes Free

Siri Eyes Free allows you to use an iPhone

handsfree by simply speaking into the microphone.

This function requires you to connect an iPhone to

the unit via BLUETOOTH. Availability is limited

iPhone 4s or later. Make sure that your iPhone is

running the latest iOS version.

You must complete BLUETOOTH registration and

connection configurations for the iPhone with the

unit in advance. For details, see “Preparing a

BLUETOOTH Device” (page 8).

To select the iPhone, press MENU, then select

[BLUETOOTH]  [SET AUDIODEV] (page 22).

1 Activate the Siri function on the iPhone.

For details, refer to the operating instructions

supplied with the iPhone.

2 Press VOICE.

The voice command display appears.

3 After the iPhone beeps, speak into the

microphone.

The iPhone beeps again, then Siri starts

responding.

To deactivate Siri Eyes Free

Press VOICE.

Notes

 The iPhone may not recognize your voice depending

on usage conditions. (For example, if you are in a

moving car.)

 Siri Eyes Free may not function properly, or the

response time may lag in locations where iPhone

signals are difficult to receive.

 Depending on the iPhone’s operating condition, Siri

Eyes Free may not function properly, or may quit.

 If you play a track with an iPhone using the

BLUETOOTH audio connection, when the track starts

playback via BLUETOOTH, Siri Eyes Free automatically

quits and the unit switches to the BLUETOOTH audio

source.

 When Siri Eyes Free is activated during audio

playback, the unit may switch to the BLUETOOTH

audio source even if you do not specify a track to play.

 When connecting the iPhone to the USB port, Siri Eyes

Free may not function properly, or may quit.

 When connecting the iPhone to the unit via USB, do

not activate Siri with the iPhone. Siri Eyes Free may

not function properly, or may quit.

 There is no audio sound while Siri Eyes Free is

activated.

19GB

Canceling the DEMO Mode

You can cancel the demonstration display which

appears when the source is off and the clock is

displayed.

1 Press MENU, rotate the control dial to

select [GENERAL], then press it.

2 Rotate the control dial to select [SET

DEMO], then press it.

3 Rotate the control dial to select [SET

DEMO-OFF], then press it.

The setting is complete.

4 Press (back) twice.

The display returns to normal reception/play

mode.

Basic Setting Operation

You can set items in the following setup categories:

General setup (GENERAL), Sound setup (SOUND),

Display setup (DISPLAY), BLUETOOTH setup

(BLUETOOTH), SongPal setup (SONGPAL)

1 Press MENU.

2 Rotate the control dial to select the setup

category, then press it.

The items that can be set differ depending on

the source and settings.

3 Rotate the control dial to select the

options, then press it.

To return to the previous display

Press (back).

General Setup (GENERAL)

DEMO (demonstration)

Activates the demonstration: [ON], [OFF].

CLOCK-ADJ (clock adjust) (page 7)

CAUT ALM (caution alarm)

Activates the caution alarm: [ON], [OFF] (page 7).

(Available only while the source is off and the

clock is displayed.)

BEEP

Activates the beep sound: [ON], [OFF].

AUTO OFF

Shuts off automatically after a certain time when

the unit is turned off: [ON] (30 minutes), [OFF].

STEERING

Registers/resets the setting of the steering

wheel remote control.

(Available only while the source is off and the

clock is displayed.)

STR CONTROL (steering control)

Selects the input mode of the connected remote

control. To prevent a malfunction, be sure to

match the input mode with the connected

remote control before use.

CUSTOM

Input mode for the steering wheel remote

control

PRESET

Input mode for the wired remote control

excluding the steering wheel remote control

EDIT CUSTOM

Registers the functions (SOURCE, ATT, VOL +/–,

SEEK +/–, VOICE, ON HOOK, OFF HOOK) to the

steering wheel remote control:

 Rotate the control dial to select the function

you want to assign to the steering wheel

remote control, then press it.

 While [REGISTER] is blinking, press and hold

the button on the steering wheel remote

control you want to assign the function to.

When registration is complete, [REGISTERED]

is displayed.

 To register other functions, repeat steps 

and .

(Available only when [STR CONTROL] is set to

[CUSTOM].)

RESET CUSTOM

Resets the registered functions of the steering

wheel remote control: [YES], [NO].

(Available only when [STR CONTROL] is set to

[CUSTOM].)

Notes

 While making settings, only button operation on

the unit is available. For safety, park your car

before making this setting.

 If an error occurs while registering, all the

previously-registered information remains. Restart

registration from the function where the error

occurred.

 This function may not be available on some

vehicles. For details on the compatibility of your

vehicle, visit the support site on the back cover.

Settings

20GB

CT (clock time)

Activates the CT function: [ON], [OFF].

BTM (best tuning memory) (page 10)

(Available only when the tuner is selected.)

SXM PARENTAL

Sets the parental lock to [ON], [OFF], and edits

the passcode (page 12).

(Available only when SiriusXM is selected.)

SXM RESET (SiriusXM reset)

Initializes the SiriusXM Connect Vehicle Tuner

settings (preset channels/parental lock): [YES],

[NO].

(Available only when SiriusXM is selected.)

FIRMWARE

(Available only while the source is off and the

clock is displayed.)

Checks/updates the firmware version. For

details, visit the support site on the back cover.

FW VERSION (firmware version)

Displays current firmware version.

FW UPDATE (firmware update)

Enters firmware update process: [YES], [NO].

Updating the firmware takes a few minutes to

complete. During the update, do not turn the

ignition to the OFF position, nor remove the USB

device.

Sound Setup (SOUND)

This setup menu is not available when the source is

off and the clock is displayed.

EXTRA BASS

Reinforces bass sound in synchronization with

the volume level: [1], [2], [OFF].

(Automatically sets to [OFF] when [C.AUDIO+] is

set to [ON].)

C.AUDIO+ (ClearAudio+)

Reproduces sound by optimizing the digital

signal with the Sony recommended sound

settings: [ON], [OFF]. (Automatically sets to [OFF]

when [EQ10 PRESET] is changed and/or [EXTRA

BASS] is set to [1] or [2] and/or [DSO] is set to

[LOW], [MID] or [HIGH].)

EQ10 PRESET

Selects an equalizer curve from 10 equalizer

curves or off:

[OFF], [R&B], [ROCK], [POP], [DANCE], [HIP-HOP],

[ELECTRONICA], [JAZZ], [SOUL], [COUNTRY],

[CUSTOM].

The equalizer curve setting can be memorized

for each source.

EQ10 CUSTOM

Sets [CUSTOM] of EQ10.

Setting the equalizer curve: [BAND1] 32 Hz,

[BAND2] 63 Hz, [BAND3] 125 Hz, [BAND4] 250 Hz,

[BAND5] 500 Hz, [BAND6] 1 kHz, [BAND7] 2 kHz,

[BAND8] 4 kHz, [BAND9] 8 kHz, [BAND10] 16 kHz.

The volume level is adjustable in 1 dB steps,

from -6 dB to +6 dB.

POSITION (listening position)

F/R POS (front/rear position)

Simulates a natural sound field by delaying the

sound output from speakers to suit your position:

 [FRONT L] (front left),

 [FRONT R] (front right),

 [FRONT] (center front),

 [ALL] (center of your car),

[CUSTOM] (position set by the advanced car

audio settings on SongPal)

[OFF] (no position set)

ADJ POSITION (adjust position)

Fine-tunes the listening position setting: [+3] –

[CENTER] – [-3].

(Available only when [F/R POS] is not set to [OFF]

or [CUSTOM].)

SW POS (subwoofer position)

 [NEAR] (near),

 [NORMAL] (normal),

 [FAR] (far)

(Available only when [F/R POS] is set to other

than [OFF].)

DSO (dynamic stage organizer)

Creates a more ambient sound as if there were

speakers in the dashboard: [OFF], [LOW], [MID],

[HIGH].

(Automatically sets to [OFF] when [C.AUDIO+] is

set to [ON].)

BALANCE

Adjusts the sound balance: [RIGHT-15] –

[CENTER] – [LEFT-15].

FADER

Adjusts the relative level: [FRONT-15] – [CENTER]

– [REAR-15].

DSEE (digital sound enhancement engine)

Improves digitally compressed sound by

restoring high frequencies lost in the

compression process: [ON], [OFF].

This setting can be memorized for each source

other than the tuner.

La page charge ...

Sony MEX-GS620BT Manuel utilisateur

Marque: Sony

Modèle: MEX-GS620BT

Catégorie: Récepteurs multimédia de voiture

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Sony MEX-GS620BT User manual

Sony MEX-GS620BT Manuel utilisateur

Sony MEX-GS620BT Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents