CommScope T350D Mode d'emploi

Taper
Mode d'emploi
T350d Access Point
Quick Setup Guide
NOTE: The minimum soware revision for the T350d is
ZoneDirector (ZD) 10.1 or later, or SmartZone (SZ) 6.0 or later.
This Quick Setup Guide provides step-by-step instrucons on how
to eld-install the RUCKUS T350d access point (AP). For detailed
informaon on planning the installaon, performing a site survey,
and operang the T350d, refer to the RUCKUS Outdoor Access
Point User Guide, available at hps://support.ruckuswireless.com.
WARNING! Only trained and qualied personnel should be
allowed to install, replace, or service this equipment.
WARNING! Installaon of this equipment must comply with
local and naonal electrical codes.
CAUTION! Form a 80-mm to 130-mm (3-in. to 5-in.) drip loop
in any cable that is aached to the AP or the building. This will
prevent water from running along the cable and entering the
AP or the building where the cable terminates.
CAUTION! Be sure that grounding is available and that it meets
local and naonal electrical codes. For addional lightning
protecon, use lightning rods and lightning arrestors.
CAUTION! Make sure that proper lightning surge protecon
precauons are taken according to local electrical code.
CAUTION! RUCKUS strongly recommends that you wear eye
protecon before mounng the T350d.
This Guide in Other Languages
请从以下网站获得该指南的简体中文版 hps://
support.ruckuswireless.com.
Vous trouverez la version française de ce guide à l'adresse
suivante hps://support.ruckuswireless.com.
このガイドの日本語版は hps://support.ruckuswireless.com
でご覧ください。
가이드의 한국어 버전은 사이트 (hps://
support.ruckuswireless.com) 에서 확인하시기 바랍니다.
Veja a versão em português (Brasil) deste guia em hps://
support.ruckuswireless.com.
Puede ver la versión en español (América Lana) de esta guía
en hps://support.ruckuswireless.com.
Before You Begin
Before deploying RUCKUS products, please check for the latest
soware and the release documentaon.
Release Notes and other user documentaon are available at
hp://support.ruckuswireless.com/documents.
Soware upgrades are available at hp://
support.ruckuswireless.com/soware.
Soware license and limited warranty informaon are available
at hp://support.ruckuswireless.com/warranty.
Before deploying your RUCKUS Access Point, verify that all
items listed in Package Contents are included in the package. If
any item is damaged or missing, nofy your authorized RUCKUS
sales representave. Also, make sure that you have the
required hardware and tools.
Required Hardware and Tools
No. 2 Phillips screwdriver
Small at-blade screwdriver
Wide at-blade screwdriver
Torque wrench or torque screwdriver with sockets
Long-nose pliers
Electrical wire stripping and terminal crimping pliers
Pipe or pole, or a sturdy at surface
Electric drill with drill bits and customer-supplied wall anchors,
at washers, and hex nuts for at-surface mount
Package Contents
A complete T350d eld installaon package includes all of the
following items:
T350d Access Point
M25 data cable gland
Ground wire with lug
Pole/Wall Mount Bracket Kit
Two steel pipe clamps
Service Level Agreement/Limited Warranty Statement
Declaraon of Conformity
Regulatory Statement
RUCKUS AP Geng Started Guide
AP Cloud Management insert
This Quick Setup Guide
FIGURE 1 T350d Package Contents
1. T350d Access Point
2. M25 data cable gland
3. Ground wire with lug
4. Pole/Wall Mount Bracket Kit
Mounng Instrucons
Connecng and Sealing the RJ-45 Cables
Connect and seal the RJ-45 cables using the M25 data cable
glands.
WARNING! Do not use any PoE injector not tested and
approved by RUCKUS to power the T350d Access Point.
FIGURE 2 T350d LEDs and Ports
1. Feed the end of the cable through the sealing nut, rubber O-
ring, clamping ring assembly, and cable gland base, as shown
in Figure 3.
NOTE: Do not seat the clamping ring and rubber O-ring
into the gland body unl the gland body has been torqued
to specicaons.
Copyright © 2020 CommScope, Inc. All rights reserved. Page 1 of 4
Published April 2021, Part Number 800-72737-001 Rev A
FIGURE 3 RJ-45 Cable and Gland Assembly
2. Use a wide at-blade screwdriver to remove the required
(PoE IN) blanking cap from the AP.
3. Connect the cable to the Ethernet port on the AP.
4. Tighten the cable gland base into the AP chassis to 7 N.m or
62 in-lbs.
5. Wrap the clamping ring assembly around the rubber O-ring.
Make sure that the clamping ring assembly fully encloses the
rubber O-ring.
6. Seat the clamping ring assembly and rubber O-ring in the
cable gland base.
7. Hand-ghten the sealing nut.
Aaching the Mounng Bracket to a Flat Surface
1. The AP mounng bracket aaches to the AP using a capve
screw. Use a medium at-blade or No. 2 Phillips screwdriver
to loosen the capve screw, as shown in Figure 4, and pull up
on the end of the bracket to remove the bracket from the AP,
as shown in Figure 4.
FIGURE 4 Removing the Mounng Bracket
2. Using either of the two opons shown in Figure 5, hold the
mounng bracket at the locaon on the mounng surface
where you want to mount the AP. Use the holes on the
mounng bracket as a template to mark the locaons of the
mounng holes.
NOTE: The mounng bracket can be mounted to a vercal
or horizontal surface to support the AP in the required
orientaon.
FIGURE 5 Mounng Bracket on a Flat Surface
3. Remove the mounng bracket from the mounng surface.
4. Drill holes required for the customer-supplied mounng
hardware.
5. Aach the mounng bracket to the at surface using the
mounng hardware.
6. Using the mounng hardware instrucons, ghten the
hardware to secure the mounng bracket.
7. Connue with Mounng the AP on page 2.
Aaching the Mounng Bracket to a Pole
1. The AP mounng bracket aaches to the AP using a capve
screw. Loosen the screw and pull up on the end of the
bracket to remove the bracket from the AP, as shown in
Figure 4.
2. Insert the open end of one steel clamp into two of the slots
on the mounng bracket.
NOTE: The mounng bracket can be mounted to a vercal
or horizontal pole to support the AP in the required
orientaon.
3. Using either of the two opons shown, use the clamps to
aach the mounng bracket to the pole. Tighten the clamps
to 3 N.m or 27 in-lbs, or per manufacturers specicaons if
the factory-supplied clamps are not used.
4. If necessary, daisy-chain the other steel clamps to
accommodate larger poles.
FIGURE 6 Mounng Bracket on a Pole
5. Connue with Mounng the AP.
Mounng the AP
1. Snap the AP back onto the mounng bracket, as shown in
Figure 7, and use a medium at-blade or No. 2 Phillips
screwdriver to ghten the capve screw to 1.1 N.m or 10 in-
lbs to secure the bracket to the AP, as shown in Figure 7.
Copyright © 2020 CommScope, Inc. All rights reserved. Page 2 of 4
Published April 2021, Part Number 800-72737-001 Rev A
FIGURE 7 Aaching the Mounng Bracket to the AP
2. Oponal Step: If you also need to lock the mounng bracket
to the AP, then use an appropriately sized screwdriver to
screw the customer-supplied locking stainless steel 6-mm M3
panhead security screw through the mounng bracket and
into the AP chassis.
CAUTION! Make sure that the customer-supplied locking
stainless steel M3 panhead security screw is no longer
than 6mm. If the security screw is longer than 6mm, it can
damage the AP chassis.
FIGURE 8 Locking the Mounng Bracket to the AP
You have completed mounng the AP to the mounng bracket.
Powering the AP with DC Power
The AP can accommodate two sources of power: PoE (48V) power
and 12V DC.
The AP can draw power from the Ethernet input as a Class 4
device, providing a maximum of 18 W to the system. Alternately,
power can be supplied through a customer-provided 12V DC
power supply (12V DC preferred, 7-20V DC acceptable) that will
connect to a two-pin terminal block. The terminal block is
accessible through a water-ght gland on one end of the unit. The
terminal block connecon has surge and polarity protecon to
protect against inserng the wrong polarity leads into the
terminal block.
NOTE: When both the 12V DC and the 48V PoE power are
acve, the AP will priorize the 12V DC power.
1. Install the DC power supply as described in the DC power
supply accessory installaon guide.
2. Connect the power cord to a DC power source.
3. Verify that the PWR LED is a steady green.
Earth Grounding the AP
CAUTION! Make sure that earth grounding is available and that
it meets local and naonal electrical codes. For addional
lightning protecon, use lightning rods and lightning arrestors.
NOTE: The color coding of ground wires varies by region.
Before compleng this step, check your local wiring standards
for guidance.
Using the factory-supplied ground wire and ground screw and
washer set, connect a good earth ground to the AP chassis ground
point.
CAUTION! The T350d AP includes one 9-mm stainless steel
M6x1 earth ground screw with split lock and at washers.
Make sure that any replacement screw is no longer than 9 mm.
If a screw is longer than 9 mm, it can damage the AP chassis.
FIGURE 9 Connecng a Good Earth Ground to the AP
1. Earth ground screw
Installing a USB Dongle
To install a USB dongle (for example, an IoT radio device such as
BLE, 802.15.4, Z-wave, or similar), remove the two 3-mm hex
screws, remove the cap, and insert the dongle into the USB port.
Once installed, replace the cap and the hex screws, and ghten
the screws to 0.79 N.m or 7 in-lbs.
NOTE: If required, a larger USB dongle cap can be purchased
separately. The maximum dimensions of the USB dongle that
can be inserted (with the large USB dongle cap, part #
902-0127-000) are 6 cm x 2 cm x 1.1 cm. Max Power: 450mW
(SiLabs EM3578 max current draw at +20 dBm is 80mA over a
3.3V rail).
Copyright © 2020 CommScope, Inc. All rights reserved. Page 3 of 4
Published April 2021, Part Number 800-72737-001 Rev A
FIGURE 10 Installing a USB Dongle
Troubleshoong
CAUTION! If required, you can reset the AP to its factory
default sengs by pressing the reset buon located inside the
PoE IN port. Use the p of a pen or a 3-mm at-blade
screwdriver to press the reset buon. Press and hold the reset
buon for 4 seconds or longer to restore to factory defaults.
DO NOT RESET THE AP TO FACTORY DEFAULT SETTINGS UNLESS
SO INSTRUCTED. (Doing this resets the AP IP address to
192.168.0.1.)
NOTE: Aer a reset, you can access the internal AP web
interface using hps://192.168.0.1. Your device must use any
other address from 192.168.0.2 through 192.168.0.254, with
subnet mask 255.255.255.0. The username is super, and the
password is sp-admin. Refer to the Outdoor Access Point User
Guide for informaon on conguring and operang the AP. This
document is available at hps://support.ruckuswireless.com.
For More Informaon
For informaon on how to congure and manage the AP, refer to
the RUCKUS Access Point User Guide, available from hps://
support.ruckuswireless.com.
RUCKUS WIRELESS, Inc. is a wholly owned subsidiary of
CommScope, Inc.
© 2020 CommScope, Inc. All rights reserved.
ARRIS, the ARRIS logo, COMMSCOPE, RUCKUS, RUCKUS WIRELESS, the Ruckus
logo, and the Big Dog design are trademarks of CommScope, Inc. and/or its
aliates. Wi-Fi Alliance, Wi-Fi, the Wi-Fi logo, Wi-Fi Cered, the Wi-Fi
CERTIFIED logo, Wi-Fi Protected Access, the Wi-Fi Protected Setup logo, Wi-Fi
Protected Setup, Wi-Fi Mulmedia and WPA2 and WMM are trademarks or
registered trademarks of Wi-Fi Alliance. All other trademarks are the property of
their respecve owners.
Copyright © 2020 CommScope, Inc. All rights reserved. Page 4 of 4
Published April 2021, Part Number 800-72737-001 Rev A
Business Unit - Ruckus Wireless Inc.
350 West Java Dr.
Sunnyvale CA 94089 USA
T: +1 650 265 4200
F: +1 408 738 2065
www.commscope.com
1
Declaration of Conformity
This declaration of conformity is issued under the sole responsibility of the manufacturer:
Ruckus Wireless, Inc., 350 West Java Drive Sunnyvale, CA 94089 USA
Object of declaration
Product Name: T350d & T350c Access Point
Brand: RUCKUS
Model: T350d & T350c
The object of the declaration described above is in conformity with the relevant Union harmonization legislation:
Radio Equipment Directive 2014/53/EU and the RoHS directive 2011/65/EU
The product to which this declaration relates is in conformity with the following standards:
Safety
IEC 62368-1:2014 2nd Ed.
EN 62368-1:2014, AC:2017, A11:2017
EN 60950-22:2016
IEC 60950-1:2005, A1:2009, A2:2013
EN 60950-1: 2006 /A11:2009
/A1:2010/A12:2011 /A2:2013
EMF
EN 62311:2008
EN 50385 2017
EMC
EN 301 489-1 V2.1.1
EN 301 489-17 V3.1.1
RF
EN 300 328 V2.2.2
EN 301 893 V2.1.1
EN 302 502 V2.1.1
RoHS
EN IEC 63000:2018
Additional Information
EU-Type examination issued by NB
Signed for and on behalf of Ruckus Wireless Inc.
Signature:
Name: Ivaylo Tankov
Tittle: Principal Wireless Compliance Engineering
Date: 12 February 2021
Note: Find the complete set of AP documentation for all RUCKUS Wi-Fi products at
http://docs.commscope.com/?docs-box.
2
T350d, T350c – Outdoor Enterprise AP Ruckus Wireless Inc., a CommScope Company
Federal Communications Commission Notices
This product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
Caution: Changes or modifications to this equipment that have not been approved by Ruckus Wireless may void the user's authority to
operate this equipment.
For Class B Equipment:
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna. - Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected
—Increase the separation between the equipment and receiver. - Consult the dealer or an experienced radio/TV technician for help.
This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules. This transmitter must not be co-
located or operating in conjunction with any other antenna or transmitter.
Note: The country code selection is for non-US Products only and is not available on US Products. Per FCC regulation, Wireless product
marketed in the US must be restricted to operate only on spectrum allocated per FCC Rules and Regulations.
Canada Statement
Under ISED regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the
transmitter by ISED. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
Conformément à la réglementation d’ISED, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal
(ou inférieur) approuvé pour l'émetteur par ISED. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres
utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas
l'intensité nécessaire à l'établissement d'une communication satisfaisante.
This device complies with ISED licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may
not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the
device.
Le présent appareil est conforme aux CNR d'ISED applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux
deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel
mobile satellite systems; the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall comply
with the e.i.r.p. limit; and the maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply with the e.i.r.p. limits
specified for point-to-point and non point-to-point operation as appropriate.
Le dispositif de fonctionnement dans la bande 5150-5250 MHz est réservé à une utilisation en intérieur pour réduire le risque
d'interférences nuisibles à la co-canal systèmes mobiles par satellite, le gain d'antenne maximal autorisé pour les appareils dans les
bandes 5250-5350 MHz et 5470-5725 MHz doit se conformer à la pire limite, et le gain d'antenne maximal autorisé pour les appareils
dans la bande 5725-5825 MHz doivent être conformes avec le pire limites spécifiées à point-à-ponctuelles et non point-à-point de
fonctionnement selon qu'il convient.
Operation in the 5600-5650 MHz band is not allowed in Canada. High-power radars are allocated as primary users (i.e. priority users) of
the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.
Opération dans la bande 5600-5650 MHz n'est pas autorisée au Canada. Haute puissance radars sont désignés comme utilisateurs
principaux (c.-à-utilisateurs prioritaires) des bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer des
interférences et / ou des dommages à dispositifs LAN-EL.
Radiation Exposure Statement
The device has been found to be compliant to the requirements set forth in CFR 47 Sections 2.1091 and ISED RSS-102 for an
uncontrolled environment. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm
from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
Le dispositif a été jugé conforme aux exigences énoncées dans les articles 47 CFR 2.1091 et ISED RSS-102 pour un environnement non
contrôlé. L'antenne (s) utilisée pour ce transmetteur doit être installé pour fournir une distance de séparation d'au moins 20 cm de toutes
les personnes et ne doit pas être co-localisés ou fonctionner en conjonction avec une autre antenne ou transmetteur.
Professionally Installed Products
The product is to be installed according to the installation instructions. The Use/Operator does not have access to the device once the
device is installed and in use. Provisions for permanent grounding is provided.
1. Installation personal: This product is designed for specific application and needs to be installed by a qualified personal who has RF and
related rule knowledge. The general user shall not attempt to install or change the setting.
2. Installation location: The product shall be installed at a location where the radiating antenna can be kept 20 cm from nearby person in
normal operation condition to meet regulatory RF exposure requirement
3
a. Any installation of either a master or a client device within 35 km of a TDWR location shall be separated by at least 30 MHz
center-to-center) from the TDWR operating frequency.
b. A voluntary WISPA sponsored database has been developed that allows operators and installers to register the location
information of the UNII devices operating outdoors in the 5470 – 5725 MHz band within 35 km of any TDWR location (see
http://www.spectrumbridge.com/udia/home.aspx ). This database may be used by government agencies in order to expedite
resolution of any interference to TDWRs.
c. Addition information can be obtained from the FCC Knowledge Database, Publication Number 443999.
https://apps.fcc.gov/oetcf/kdb/index.cfm
3. External antenna: Use only the antennas which have been approved by Ruckus Wireless. The non-approved antenna(s) may produce
unwanted spurious or excessive RF transmitting power which may lead to the violation of FCC limit and is prohibited.
4. Installation procedure: Please refer to user’s manual for the detail.
5. Warning: Please carefully select the installation position and make sure that the final output power does not exceed the limit set force in
US Rule CFR 47 part 15 section 15.247 & 15.407. The violation of the rule could lead to serious federal penalty.
Products intended to be powered by an external power supply:
Caution –This product is intended to be supplied by a Listed Direct Plug-In Power Unit marked Class 2 or LPS (sub-clause 2.5 of standard
EN 60950-1). Available Ruckus power supplies intended for product operation are identified in the product datasheet. The last two digits
of the power supply part number represent the country code. For additional applicable power supplies/options, see user instructions and
product datasheet.
Medical Statement
Ruckus Wireless Access Points shall only be used in ME systems where the intended EM ENVIRONMENT does NOT does not rely on the
WLAN radio link for BASIC SAFETY or ESSENTIAL PERFORMANCE of the ME SYSTEM.
Mexico Statement
“La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause
interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación
no deseada.”
Australia and New Zealand Statement
This device complies with the ACMA requirements for a WiFi device namely Radiocommunications (Short Range Devices) 2014 and
Radiocommunications (Compliance Labelling – Devices) Notice 2014 and the New Zealand Radiocommunications Regulations (General
User Radio Licence for Short-Range Devices). The equipment complies with the ACMA and New Zealand requirements for radiation
exposure for a “general user/non-aware user”. This equipment should be installed and operated with a minimum distance of 20 cm
between the radiator and your body. This equipment complies with the Australian and New Zealand safety requirements and should only
be used with the specified power adapter carrying a RCM mark and Electrical Approval No.
Brazil Statement
For Brazil, those products are designed for specific application and needs to be installed by a qualified personal who has RF and related
rule knowledge. Regarding the operation on range of 5150 MHz to 5350 MHz, the average output power of the equipment must be
adjusted to the maximum limit of - 0,48 dBm and for 5470 MHz to 5725 MHz, the average output power of the equipment must be adjusted
to the maximum limit of 6,44 dBm.
Para o Brasil, esses produtos são projetados para aplicações específicas e necessidades a serem instalados por um pessoal qualificado
que tenha conhecimento regra RF e afins.Em relação à operação em série de 5150 MHz a 5350 MHz, a potência média de saída dos
equipamentos deve ser ajustado para o limite máximo de - 0,48 dBm e para 5470 MHz a 5725 MHz, a potência média de saída dos
equipamentos deve ser ajustada ao limite máximo de 6,44 dBm.
Este equipamento não tem direito à proteção contra interferência prejudicial e não pode causar interferência em sistemas devidamente
autorizados.
Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do
mesmo tipo, e não pode causa interferência a sistemas operando em caráter primário
Nigeria Statement
Connection and use of this communications equipment is permitted by the Nigerian Communications Commission
Thailand Statement
This telecommunication equipment conforms to NTC technical requirement
Hong Kong Statement
The 5.15 – 5.35 GHz band shall be restricted to indoor operations only. Obey local regulations when using this product.
Taiwan Statement
使用此品時應避免影響附近雷達系統之操作 This product should not affect the operation of nearby radar systems.
經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。
低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象時,應立即停用,並改善至無干擾時方得繼續使用。前項合法
通信,指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾.
The control, adjustment and on/off operation of this device does not violate the “Administrative regulations on low power radio waves
radiated devices”. Any adjustments to the device should be carried out or be monitored by a specialist who has expertise on radio
frequency devices. Replacement of components which may lead to the violation to the regulations is not allowed. Without permission
granted by the NCC, any company, enterprise, or user is not allowed to change frequency, enhance transmitting power or alter original
characteristic as well as performance to an approved low power radio-frequency devices. The low power radio-frequency device shall not
influence aircraft security and interfere with legal communications; if found, the user shall cease operating immediately until no
interference is achieved. The said legal communications means radio communications is operated in compliance with the
4
Telecommunications Act. The low power radio-frequency devices must not be susceptible with the interference from legal communications
or ISM radio wave radiated devices.
限用物質含有情況標示聲明書
設備名稱:無線網路基地台,型號(型式)T350d & T350c
Equipment name Type designation (Type)
單元Unit
限用物質及其化學符號 Restricted substances and its chemical symbols
Lead (Pb)
Mercury
(Hg)
六價鉻Hexavalent
chromium (Cr+6)
多溴聯苯
Polybrominated
Biphenyls (PBB)
多溴二苯醚
Polybrominated
diphenyl ethers (PBDE)
Enclosure - Top
頂部外殼
O
O
O
O
O
Enclosure - Bottom
底部外殼
O
O
O
O
O
PWB
電路板
O
O
O
O
Connector and Receptacle
插口
O
O
O
O
O
備考1.〝超出0.1 wt %〞及〝超出0.01 wt %〞係指限用物質之百分比含量超出百分比含量基準值。
備考2.O〞係指該項限用物質之百分比含量未超出百分比含量基準值。
備考3.〝-〞係指該項限用物質為排除項目。
Thailand
European Union Notices and National Restrictions
:
Maximum output power:
2400-2483.5MHz: 19.9dBm EIRP
5150-5250MHz: 22.9dBm EIRP
5250-5350MHz: 22.9dBm EIRP
5470-5725MHz: 29.9dBm EIRP
The frequency band 5150 – 5350 MHz is restricted to indoor use.
Note 1“Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the percentage content of the restricted substance exceeds the
reference percentage value of presence condition.
Declaration of the Presence Condition of the Restricted Substances Marking
Note 2“○” indicates that the percentage content of the restricted substance does not exceed the percentage of reference value of presence.
Note 3The “−” indicates that the restricted substance corresponds to the exemption.
5
Hereby, Ruckus Wireless Inc., declares that the radio equipment type is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address: http://docs.commscope.com/?docs-box
Български
[Bulgarian]
С настоящото Ruckus Wireless декларира, че описаното по-горе радиосъоръжение е в съответствие с
Директива 2014/53/ЕС.
Česky
[Czech]
Ruckus Wireless tímto prohlašuje, že tento Radio LAN je ve shodě se základními požadavky a dalšími
příslušnými ustanoveními směrnice 2014/53/EU.
Dansk
[Danish]
Undertegnede Ruckus Wireless erklærer herved, at følgende udstyr Radio LAN overholder de væsentlige krav og
øvrige relevante krav i direktiv 2014/53/EU.
Deutsch
[German]
Hiermit erklärt Ruckus Wireless, dass sich das Gerät Radio LAN in Übereinstimmung mit den grundlegenden
Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 2014/53/EU befindet.
Eesti
[Estonian]
Käesolevaga kinnitab Ruckus Wireless seadme Radio LAN vastavust direktiivi 2014/53/EÜ põhinõuetele ja
nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.
English
Hereby, Ruckus Wireless declares that this Radio LAN is in compliance with the essential requirements and other
relevant provisions of Directive 2014/53/EU.
Español
[Spanish]
Por medio de la presente Ruckus Wireless declara que el Radio LAN cumple con los requisitos esenciales y
cualesquiera otras disposiciones aplicables o exigibles de la Directiva 2014/53/EU.
Ελληνική
[Greek]
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Ruckus Wireless ΔΗΛΩΝΕΙ ΟΤΙ Radio LAN ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ
ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 2014/53/EU.
Français
[French]
Par la présente Ruckus Wireless déclare que l'appareil Radio LAN est conforme aux exigences essentielles et
aux autres dispositions pertinentes de la directive 2014/53/EU.
Italiano
[Italian]
Con la presente Ruckus Wireless dichiara che questo Radio LAN è conforme ai requisiti essenziali ed alle altre
disposizioni pertinenti stabilite dalla direttiva 2014/53/EU.
Latviski
[Latvian]
Ar šo Ruckus Wireless deklarē, ka Radio LAN atbilst Direktīvas 2014/53/EU būtiskajām prasībām un citiem ar to
saistītajiem noteikumiem.
Lietuvių
[Lithuanian]
Šiuo Ruckus Wireless deklaruoja, kad šis Radio LAN atitinka esminius reikalavimus ir kitas 2014/53/EU
Direktyvos nuostatas.
Nederlands
[Dutch]
Hierbij verklaart Ruckus Wireless dat het toestel Radio LAN in overeenstemming is met de essentiële eisen en de
andere relevante bepalingen van richtlijn 2014/53/EU.
Malti
[Maltese]
Hawnhekk, Ruckus Wireless, jiddikjara li dan Radio LAN jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti
oħrajn relevanti li hemm fid-Dirrettiva 2014/53/EU.
Magyar
[Hungarian]
Alulírott, Ruckus Wireless nyilatkozom, hogy a Radio LAN megfelel a vonatkozó alapvetõ követelményeknek és
az 2014/53/EU irányelv egyéb elõírásainak.
Polski
[Polish]
Niniejszym Ruckus Wireless oświadcza, że Radio LAN jest zgodny z zasadniczymi wymogami oraz pozostałymi
stosownymi postanowieniami Dyrektywy 2014/53/EU.
Português
[Portuguese]
Ruckus Wireless declara que este Radio LAN está conforme com os requisitos essenciais e outras disposições
da Directiva 2014/53/EU.
Slovensko
[Slovenian]
Ruckus Wireless izjavlja, da je ta Radio LAN v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili
direktive 2014/53/EU.
Slovensky
[Slovak]
Ruckus Wireless týmto vyhlasuje, že Radio LAN spĺňa základné požiadavky a všetky príslušné ustanovenia
Smernice 2014/53/EU.
Suomi
[Finnish]
Ruckus Wireless vakuuttaa täten että Radio LAN tyyppinen laite on direktiivin 2014/53/EU oleellisten vaatimusten
ja sitä koskevien direktiivin muiden ehtojen mukainen.
Svenska
[Swedish]
Härmed intygar Ruckus Wireless att denna Radio LAN står I överensstämmelse med de väsentliga
egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 2014/53/EU.
Íslenska
[Icelandic]
Hér með lýsir Ruckus Wireless yfir því að Radio LAN er í samræmi við grunnkröfur og aðrar kröfur, sem gerðar
eru í tilskipun 2014/53/EU.
Norsk
[Norwegian]
Ruckus Wireless erklærer herved at utstyret Radio LAN er i samsvar med de grunnleggende krav og øvrige
relevante krav i direktiv 2014/53/EU.
6
T350d & T350c, Access Point Installation Addendum
When the frequency band 5150 5250 MHz is used outdoors in the U.S.A, the FCC mandates that the energy radiated above 30° from
the horizon remains below 21 dBm EIRP. This can be maintained during installation using the following guidance.
When the device is installed level to the horizon, (i.e. – device perpendicular to the surface of the earth, antenna radome pointing
horizontal, parallel to the earth), the device operates in compliance with FCC rules without any adjustment of output power.
T350d & T350s – Antennas
When the device is installed outdoors at an angle above the
horizon, it may be necessary to reduce output power to ensure
the energy radiated
above 30° from the horizon remains under 21 dBm EIRP.
Please see table and elevation plots below.
T350d & T350d Omni Antenna
Elevation Pattern: The highest gain is -3.7dBi above 30° to 150°
0° reference
Degree Above Horizon (A)
Output Power Reduction (dBm)
A <=12
0 dBm
12 < A <15
1 dBm
15 <= A < 30
3 dBm
30 <= A < 45
6 dBm
A > 45
7dB
800-72680-001-A1
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

CommScope T350D Mode d'emploi

Taper
Mode d'emploi

dans d''autres langues