DK2 TMC201 Manuel utilisateur

CUSTOMER SERVICE 1 (888) 277-6960 | MONDAY - FRIDAY 8AM - 4PM EST | WWW.DK2.COM

DK2 USA WEST

3311 MEADE AVENUE STE

E DOCK 13, LAS VEGAS, NEVADA

89102 USA

DK2 USA EAST

3750 SOUTH AVENUE

NORTH UNIT, TOLEDO, OHIO

43615 USA

DK2 CORPORATE HEAD OFFICE

5330 MAINWAY

BURLINGTON, ONTARIO

L7L6A4 CANADA

TMC201

HITCHMOUNTED MOTORCYCLE CARRIER

TILTDOWN CAPABILITY  PLATFORM DESIGN  HITCHMOUNTED

USER MANUAL

IMPORTANT: RETAIN FOR FUTURE REFERENCE AND READ CAREFULLY BEFORE USE.

PLEASE DO NOT RETURN TO YOUR RETAILER.

2 | TMC201 man.

WARRANTY

WHAT IS COVERED

DK2 Inc. warrants to the original purchaser of a DK2 Inc. item that the product will be warrantied for a period of one

(1) year from the date of the original purchase.

If within one (1) year from the original date of purchase this product fails due to defect in material or workmanship,

DK2 Inc. will repair, replace, or supply any defective part at our option. Upon expiry of one (1) year, DK2 Inc. will

have no further liability related to the product.

DK2 Inc. does not authorize any party, including its authorized distributors or dealers, to oer any other warranty

on behalf of DK2 Inc.

THIS WARRANTY DOES NOT COVER OR APPLY TO:

(a) Damage to the product due to misuse, mishandling and abuse

(b) Improper installation, maintenance and storage

(c) Expendable parts such as nuts and bolts, pins and springs.

(d) Normal wear and tear

(e) Consequential damage & incidental damages such as damage to persons or property

This DK2 Inc. product is intended for personal use only. It is not intended for commercial use and subsequent use

in this capacity will void all warranty claims.

PROCEDURE FOR OBTAINING A RETURN AUTHORIZATION

Within the one (1) year warranty period, the purchaser of the product must notify an authorized distributor or dealer

of the claimed defect and provide proof of original purchase. At this time the validity of the claim will be determined

and a Return Goods Authorization Number (RGA#) will be issued if approved. No returned product will be accepted

under warranty unless accompanied by an RGA# issued by DK2 Inc.

RESOLUTION FOR A DEFECTIVE PRODUCT

DK2 Inc. will at its option repair or replace the defective product covered by this warranty. The repaired product

will be shipped to the purchaser upon completion. All transportation charges shall be the responsibility of the

purchaser. Any damage in transit will be the responsibility of the carrier or at the risk of the purchaser.

REGISTERING YOUR PRODUCT

Please take a minute and visit our website to register your product at www.DK2.com.

ENGLISH

v.220513 | 3

TABLE OF CONTENTS

WARRANTY ..........................................................................2

TABLE OF CONTENTS ................................................................3

TECHNICAL SPECIFICATIONS ..........................................................4

SECTION I  SAFETY ..............................................................5

SAFETY CONVENTIONS ..............................................................6

IMPORTANT SAFETY INFORMATION ....................................................6

SECTION II  ASSEMBLY & LOADING ................................................9

ASSEMBLY OVERVIEW ...............................................................10

STEP 1: HITCH ASSEMBLY ............................................................12

STEP 2: INSTALL THE HITCH ASSEMBLY ...............................................12

STEP 3: FRONT WHEEL CHANNEL .....................................................13

STEP 4: HITCHING TO YOUR VEHICLE .................................................14

STEP 5: SLIDING TIEDOWN TUBE ..................................................... 15

STEP 6: LOCK PIN ...................................................................16

STEP 7: LOADING THE MOTORCYCLE ................................................. 17

STEP 8: SECURING THE MOTORCYCLE ................................................18

SECTION III  PARTS & SCHEMATICS ...............................................19

SCHEMATICS .......................................................................20

PARTS LIST .........................................................................21

ENGLISH

4 | TMC201 man.

TECHNICAL SPECIFICATIONS

MODEL NUMBER TMC201

MOUNT STYLE Hitch-mounted

COUPLER 2” (5.08cm)

WEIGHT CAPACITY

To determine the

maximum weight

capacity of your Hitch-

Mounted Motorcycle

Carrier, review this

chart.

HITCH / VEHICLE

TONGUE WEIGHT LIMIT

(USE LOWEST FIGURE)

MAXIMUM WEIGHT CAPACITY OF CARRIER (YOUR

MOTORCYCLE MUST NOT WEIGH MORE THAN

THIS)

300lb (136kg) 180lb (82kg)

350lb (159kg) 225lb (102kg)

500lb (227kg) 350lb (159kg)

750lb (340kg) or more 400lb (204kg) max

ASSEMBLED

DIMENSIONS

55” (L) x 21” (W) x 7” (H)

139.7cm (L) x 53.3cm (W) x 17.8cm (H)

ASSEMBLED WEIGHT 86lb (39kg)

SHIPPING DIMENSIONS 56” (L) x 18.1” (W) x 7.9” (H)

155.5cm (L) x 46cm (W) x 20cm (H)

SHIPPING WEIGHT 89lb (40.4kg)

ENGLISH

SECTION I • SAFETY

6 | TMC201 man.

SAFETY CONVENTIONS

DANGER: This indicates a hazardous situation, which, if not avoided, will result in death

or serious injury.

WARNING: This indicates a hazardous situation, which, if not avoided, could result in

death or serious injury.

CAUTION: This indicates a hazardous situation, which, if not avoided, may cause minor

or moderate injury.

ADDITIONAL INFORMATION AND POTENTIAL CHANGES

We reserve the right to discontinue, change, and improve our products at any time without

notice or obligation to the purchaser. The descriptions and speciﬁcations contained in this

manual were in eect at printing. Equipment described within this manual may be optional.

Some illustrations may not be applicable to your product.

IMPORTANT SAFETY INFORMATION

WARNING: Read and understand the complete User Manual before

assembling or using this product. Failure to comprehend and comply with

warnings, cautions and instructions for assembly and operation could result in

serious injury or death.

WARNING: Do not permit others that have not read and understood the complete User

Manual to use this product. It is the sole responsibility of the user to understand the

assembly and safe operation of this product.

DANGER: INTENDED USE

Do not use this product for any purpose other than carrying motorcycles, for which it was

designed. Any other use is unauthorized and may result in serious injury or death.

DANGER: GENERAL SAFETY

Failure to follow warnings, cautions, and assembly instructions in the User Manual may

result in serious injury or death.

ENGLISH

v.220513 | 7

CAUTION: GENERAL REMARKS

• Please read and observe the instructions carefully before you use the product, and keep

them in a safe place for future use. Check the parts list after opening the package. Make

sure that all parts are fully assembled according to the instruction before ﬁtting it into

your car.

• The user is responsible for assembly and installation of this product, and the

manufacturer disclaims any liability due to improper ﬁtting or use of this product.

• Failure to properly install this motorcycle carrier and/or the motorcycle may cause

damage to the vehicle and/or the motorcycle, and may result in personal injury.

• Do not modify any components of the product and remove the carrier if not in use.

• This motorcycle carrier is designed to be ﬁtted directly on vehicles with a 2” (5.08cm)

hitch receiver.

WARNING: SAFE AND PROPER USE

• Please make sure you clean the surface of the hitch receiver completely before installing

the carrier.

• Always secure the wheels of the motorcycle to the carrier.

• Check if distance from the exhaust pipe to the motorcycle tires is safe for your

motorcycle. The heat of the exhaust could damage the motorcycle or the carrier.

• If your vehicle is equipped with an automatic tailgate opening system, disable this

function when using the carrier, and open the tailgate manually.

• When loading the motorcycle, remove all loose parts and accessories from the

motorcycle.

• The user is responsible for periodically verifying that all hardware is securely tightened

for safety purposes.

• Do not open the tailgate with the motorcycle installed on the carrier.

WARNING: ROAD SAFETY

• The motorcycle carrier increases the vehicle’s length, and the motorcycle may increase

its width and height. Be aware of this when passing through narrow or low-clearance

spaces and when reversing. Any loads exceeding the indicated dimensions must

nevertheless respect existing regulations and be properly secured.

• The load of the carrier and motorcycles will aect driving. Do not exceed the speed limit,

and do not drive faster than 74.5 mph (120 km/h).

• Drive slowly over speed bumps. Respect the speed limit, and adapt your speed to the

condition of the road.

• O-road driving is not recommended and could result in damage to your vehicle, hitch

receiver, motorcycle carrier, or your motorcycle.

• If you hit a bump or hole in the road, stop your vehicle and inspect the motorcycle and

the carrier. If you notice anything wrong, remove the motorcycle and do not use the

motorcycle carrier.

• Make sure there is a safe distance between the motorcycle and the ground, especially

when entering a driveway.

ENGLISH

8 | TMC201 man.

CAUTION: MAINTAINING YOUR MOTORCYCLE CARRIER

• Periodically inspect the product for signs of wear, corrosion and fatigue.

• Do not use the carrier with defective parts, contact the dealer to replace them before

using it again.

• Remove the product before entering an automatic car wash.

• To keep your product in the best condition, it is recommended to remove the product

from your vehicle when not in use. Please be advised that this product is not designed to

resist extreme weather conditions, especially seacoast air.

• Lubricate the bolts in order to avoid corrosion.

WARNING

• There is an inherent risk involved in the use of loading, unloading and transport of cargo.

DK2 Inc. assumes no liability whatsoever for damage or injury incurred during the use of

this product.

• Inspect the Hitch-Mounted Motorcycle Carrier before each use. Tighten any loose

hardware and replace any worn or damaged parts. Check that brake lights, turn signals,

and tail-lights all function properly.

• Ensure that the 5/8” hitch receiver pin is attached and locked. Safety chains must be

attached at all times. WedgeLock Nut must be tightened securely.

• Do not overload. Maximum capacity is 350lb (159kg) on a hitch receiver with maximum

tongue weight rating of 500lb (227kg). Maximum capacity is 400lb (181kg) on a hitch

receiver with maximum tongue weight rating of 750lb (340kg). See chart on Technical

Speciﬁcations (page 4).

• Ensure the motorcycle is securely fastened to the carrier. DK2 Inc. assumes no liability

whatsoever for damage caused by motorcycles that were not properly secured. Never

ride the motorcycle onto the carrier.

• Do not obstruct your license plate from view. If necessary, re-located license plate as per

local laws.

• Do not exceed the tongue weight of your vehicle or the tongue weight limit for your

hitch receiver. These may be two dierent ﬁgures. It is your responsibility to ensure that

your hitch receiver tongue weight limit is equal to or less than the limit for the vehicle.

This should have been determined at the time the hitch receiver was installed. DK2 Inc.

assumes no responsibility whatsoever for hitch receivers that are damaged, improperly

installed, or have a weight capacity which exceeds the safe limit for the vehicle.

CAUTION

Do not use the Hitch-Mounted Motorcycle Carrier if it sits at a dangerously low height

relative to the ground. The Carrier and/or front wheel of the loaded motorcycle may

“bottom out” while driving and damage may occur. It is up to the operator to determine

what is a safe height for the Carrier, and to drive accordingly.

CAUTION

Ensure tie-down straps utilized are in good condition and of the proper strength.

ENGLISH

SECTION II • ASSEMBLY & LOADING

10 | TMC201 man.

ASSEMBLY OVERVIEW

LIST OF PARTS SHOWN FOR ASSEMBLY IN THIS SECTION:

ITEM # PART # DESCRIPTION QTY. IMAGE

7

9

10

16

17

A

TMC20107

TMC20109

TMC20110

TMC20116

TMC20117

BASE ASSEMBLY

Safety Pin

Lock Pin

Main Channel

Plastic Tube Slip

Main Cross Tube

2

1

20

23

B

TMC20120

TMC20123

WEDGELOCK INNER

ASSEMBLY

Wedgelock Pin

Wedgelock Nut Tube

1

22 TMC20122 Wedgelock Bracket 1

3 TMC20103 Sliding Side Channel 2

8 TMC20108 Sliding Tie-Down Tube 1

11 TMC20111 Wheel Stop 1

12 TMC20112 Wheel Cradle 1

ENGLISH

v.220513 | 11

ITEM # PART # DESCRIPTION QTY. IMAGE

19 TMC20119 Hitch Pin 1

24 TMC20124 Chain 1

21 TMC20121 R-Clip 1

18 TMC20118 M12 U-Bolt 2

2 TMC20102 M12 Washer 8

1 TMC20101 M12 Nylock Hex Nut 8

4 TMC20104 M12 Hex Bolt 4

7 TMC20107 Safety Pin 1

ENGLISH

12 | TMC201 man.

STEP 1: HITCH ASSEMBLY

1. Separate the Wedgelock Inner Assembly (B) by removing the Wedgelock Pin (20) from the

Wedgelock Nut Tube (23).

2. Insert and re-fasten the Wedgelock Pin (20) to the Wedgelock Nut Tube (23) inside the

Wedgelock Bracket (22) as shown to complete the Hitch Assembly.

STEP 2: INSTALL THE HITCH ASSEMBLY

Fit the Base Assembly (A) over the Hitch Assembly and fasten them together using two M12

U-Bolts (18), four M12 Washers (2), and four M12 Nylock Hex Nuts (1).

A

B

20

22

23

18

21

ENGLISH

v.220513 | 13

STEP 3: FRONT WHEEL CHANNEL

1. Align the two Sliding Side Channels (3) to the two holes in the Base Assembly (A).

2. Once aligned, ﬁt the Wheel Cradle (12) and align to the same spot as shown. Fasten the

Sliding Side Channels (3) and the Wheel Cradle (12) to the Base Assembly (A) using two M12

Hex Bolts (4), two M12 Washers (2) and two M12 Nylock Hex Nuts (1).

3. Install the Wheel Stop (11) by fastening it to the Sliding Side Channel (3) as shown using two

M12 Hex Bolts (4), two M12 Washers (2), and two M12 Nylock Hex Nuts (1).

3

A12

4

2

1

2

3

11

ENGLISH

14 | TMC201 man.

STEP 4: HITCHING TO YOUR VEHICLE

Attach the motorcycle carrier to your vehicle and secure it using the Hitch Pin (19) and R-Clip

(21) as shown.

19

21

ENGLISH

v.220513 | 15

STEP 5: SLIDING TIE-DOWN TUBE

Secure the Sliding Tie-Down Tube (8) through the Base Assembly (A) using a Safety Pin (7).

A

8

7

ENGLISH

16 | TMC201 man.

STEP 6: LOCK PIN

The Lock Pin (9) is secured through the Main Channel (10) by a Safety Pin (7). To use the tilt-

down feature of the motorcycle carrier, remove the Safety Pin (7), then the Lock Pin (9), and the

Main Channel (10) will unlock for tilt-down functionality. You can temporarily store the Lock Pin

(9) into the Main Cross Tube (17) until you need to lock the carrier back in place.

9

17

7

10

ENGLISH

v.220513 | 17

STEP 7: LOADING THE MOTORCYCLE

After tilting the Main Channel (10) down, you can now mount your motorcycle.

10

ENGLISH

18 | TMC201 man.

STEP 8: SECURING THE MOTORCYCLE

1. Once the motorcycle is loaded, lift the carrier by the handles of the Main Channel (10) and

re-inserting the Lock Pin (9) and Safety Pin (7) as shown.

2. Secure the motorcycle to the handles in the Main Channel (10) with the Chain (24) as shown.

9

10 24

7

ENGLISH

SECTION III • PARTS & SCHEMATICS

20 | TMC201 man.

SCHEMATICS

1

4

2

3

12

16

17

19

20

21

22

24

23

14

15

18

75

6

8

9

10

13

11

ENGLISH

La page charge ...

DK2 TMC201 Manuel utilisateur

DK2 TMC201 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents