Sunfire Atmos XTATM265 Manuel utilisateur

Marque: Sunfire

Modèle: Atmos XTATM265

Catégorie: Subwoofers

Taper: Manuel utilisateur

Ce manuel convient également à

Atmos XTATM265230

1. AutoRoom EQ: For AutoRoom EQ starts the same way as the current TSEQ subwoofer. We have

removed the option to manually adjust the EQ on this product. The EQ Led will blink till the EQ is

complete

2. EQ On-OFF We have removed the EQ authority switch on this model and changed it to EQ-ON EQ-

OFF switch. So the user will have an option of either having the EQ ON or OFF.

3. 12V trigger: We just have the barrier jack for 12V trigger.

4. Output: On the output there is an option Bypass and 85Hz High pass. This output can be used for

full range speakers or other 2 channel setup. In the Bypass option full range signal will be passed to the

speakers. In case of 85Hz high pass, only 85hz and above will be passed on to the speakers.

5. Slave output: Slave output will be used to add more than one subwoofer to the system. In this case

the 1st subwoofer will control the EQ for the system, volume for the system, phase for the system and

frequency for the system. Slave subwoofers will lose all those controls.

User's Manual

Important Safety Instructions

1. Read these Instructions.

Lisez ces instructions.

2. Keep these Instructions.

Conservez ces instructions.

3. Heed all Warnings.

Respectez tous les avertissements.

4. Follow all instructions.

Suivez toutes les instructions.

5. Do not use this apparatus near water.

Ne pas utiliser cet appareil près de

l'eau.

6. Clean only with a dry cloth.

Nettoyer uniquement avec un chiffon

sec.

7. Do not block any ventilation open-

ings. Install in accordance with

the manufacturer’s instructions.

Ne pas bloquer les ouvertures de

ventilation. Installer conformément aux

instructions du fabricant.

8. Do not install near any heat sources

such as radiators, heat registers,

stoves, or other apparatus (including

ampliers) that produce heat.

Ne pas installer près de sources de

chaleur telles que radiateurs, registres

de chaleur, poêles ou autres appareils

(y compris les amplicateurs)

produisant de la chaleur.

9. Do not defeat the safety purpose of the

polarized or grounding - type plug. A

polarized plug has two blades with one

wider than the other. When the pro-

vided plug does not t into your outlet,

consult an electrician for replacement of

the obsolete outlet.

Ne détruisez pas la sécurité de la

terre ou polarisées - che. Une che

polarisée possède deux lames dont une

est plus large que l'autre. Si la che

fournie ne rentre pas dans votre prise,

WARNING:

To reduce the risk of re or electric shock, do not expose

this apparatus to rain or moisture.

AVIS:

Pour réduire le risque d’incendie ou de choc électrique,

ne pas exposer cet appareil sous la pluie et l’humidité.

The lightning ash with arrowhead symbol, within an equilateral triangle, is in-

tended to alert the user to the presence of uninsulated “dangerous voltage” within

the product’s enclosure that may be of sufcient magnitude to constitute a risk of

electric shock to persons.

Le symbole de l’éclair éché dans un triangle équilatéral, est destiné à alerter

l’utilisateur de la présence d’une “tension dangereuse” dans le boîtier du produit

qui peuvent être des ampleur sufsante pour constituer un risque d’électrocution

aux personnes.

This symbol is intended to alert the user to the presence of important operation

and maintenance (servicing) instructions in the literature accompanying the

appliance.

Ce symbole est destiné à alerter l’utilisateur de la présence d’opération et de

maintenance (entretien) dans la documentation accompagnant l’appareil.

The apparatus shall not be exposed to dripping or splashing and that no objects lled with

liquids, such as vases, shall be placed on apparatus.

L’appareil ne doit pas être exposé aux écoulements ou aux éclaboussures et aucun objet

ne contenant de liquide, tel qu’un vase, ne doit être placé sur l’objet.

User's Manual

consultez un électricien pour remplacer

la prise obsolète.

10. Protect the power cord from being

walked on or pinched particularly at

plugs, convenience receptacles, and

the point where they exit from the ap-

paratus.

Protégez le cordon d'alimentation d'être

piétiné ou pincé, particulièrement au

niveau des ches, des prises, et le

point où ils sortent de l'appareil.

11. Only use attachments/accessories

specied by the manufacturer.

N'utilisez que des accessoires spéciés

par le fabricant.

12. Use only with a cart, stand, tripod,

bracket, or table specied by

the manufacturer, or sold with

the apparatus. When a cart

or rack is used, use caution

when moving the cart/appa-

ratus, combination to avoid injury from

tip-over.

Utilisez uniquement un chariot, stand,

trépied, support ou table spéciés par

le fabricant ou vendu avec l'appareil.

Quand un panier ou rack est utilisé,

faites attention lorsque vous déplacez

l'ensemble chariot / appareil, pour

éviter d'éventuelles blessures en cas

de chute.

13. Unplug this apparatus during lightning

storms or when unused for long periods

of time.

Débranchez cet appareil pendant les

orages ou lorsqu'il n'est pas utilisé

pendant de longues périodes de temps.

14. Refer all servicing to qualied service

personnel. Servicing is required when

Safety Instructions .......................2

Introduction ..................................4

Features ....................................4

Unpacking and Care ....................4

Overview ....................................5

Control Panel Features ................6

Installation ...................................9

Connections ...............................10

Location ..................................11

Room Equalization Procedure ...12

System Congurations ..............14

Adjusting the Controls ...............18

Specications ............................19

Troubleshooting Guide ..............21

Limited Warranty ........................23

Service Assistance ....................23

Table of Contents

sunre.com

the apparatus has been damaged in

any way, such as power-supply cord

or plug is damaged, liquid has been

spilled or objects have fallen into the

apparatus, the apparatus has been

exposed to rain or moisture, does not

operate normally, or has been dropped.

Conez toute réparation à un personnel

qualié. Une réparation est

nécessaire lorsque l'appareil a été

endommagé de quelque façon que ce

cordon d'alimentation ou la che est

endommagé, liquide a été renversé ou

des objets sont tombés dans l'appareil,

l'appareil a été exposé à la pluie ou à

l'humidité, ne fonctionne pas

normalement, ou s'il est tombé.

15. WARNING: The mains plug (appliance

coupler) is used as disconnect device,

the disconnect device shall remain

readily operable.

AVERTISSEMENT: La che

d'alimentation (appareil coupleur) est

utilisé comme dispositif de déconnexion,

le dispositif de déconnexion doit rester

facilement accessible.

16. No naked ame sources, such as

lighted candles, should be placed on

the apparatus.

Aucune source de amme nue, telle

que des bougies allumées, ne doit être

placé sur l'appareil

17. Protective earthing terminal. The appa-

ratus should be connected to a mains

socket outlet with a protective

earthing connection.

Borne de terre de protection. L'appareil

doit être connecté à une prise secteur

avec une prise de terre.

User's Manual

Your Sun re Subwoofer should reach you

in perfect con di tion. If you do notice any

ship ping dam age, please contact your

Sun re Dealer im me di ate ly.

Gently lift out the unit and remove all the

packing material. It is im por tant to save

all the packing ma te ri als and the box in

case your subwoofer ever needs to be

moved or shipped for repair.

Make sure that you keep your sales

receipt. It is the only way to establish

the duration of your Limited Warranty

and it may come in useful for insurance

pur pos es.

Please take a moment to  ll out and mail

the Sun re Customer Response card.

Also read the serial num ber located on

the control panel and record it here:

Unpacking

Features

• 1400 watt, high ef ciency ampli er

• Automatic Room Equalization mode

• Measurement Microphone included

• Very low distortion

• Long throw, premium quality drivers

• Stunning output from a small cube!

• Automatic signal-sensing turn-on and

standby mode

• 12 VDC trigger input for remote turn-on

• Line-level unbalanced inputs

• Line-level outputs with high-pass or full-

range switch

• Continuously variable phase control

• Continuously variable crossover fre-

quency adjustment, 30 to 100 Hz

• Continuously variable volume level

control

• Soft clipping circuit allows graceful

overload and prevents speaker dam age

due to clipping

• Gold-plated inputs and outputs.

Thank you for purchasing this Sun re

ATMOS Subwoofer. We hope you enjoy

it and the music it makes as much as we

have enjoyed creating it for you.

The big breakthrough features of the

subwoofer are its uncanny tracking

downconverter, its long throw, high

back-electromotive force driver, and its

fully automatic room equalizer. Taken

together, they provide this sub woof er with

as much bass as you could get from sev-

eral 15 inch drivers mount ed in a cabinet

the size of a small re frig er a tor.

Introduction

Care

To maintain the speaker cabinet’s  nish,

 rst unplug the power cord and then use

a soft cloth to clean the sur fac es.

If your Sun re Subwoofer needs ser-

vic ing, please read the Trou ble shoot ing

section on page 21. If a problem persists,

contact your near est au tho rized Sun re

Dealer.

Serial Number:

Purchased from:

Date:

User's Manual

Your Sunre ATMOS Subwoofer is

designed to give you the best possible

low-frequency sound quality for your

Home Theater experience. It incorporates

a tremendously powerful built-in amplier

and a pair of drivers to produce tight,

oor-rumbling, denture-rattling bass that

you can feel as well as hear.

The subwoofer has an automatic

equalization system which will tailor the

subwoofer output to compensate for any

room effects.

The subwoofer has an adjustable high

cut lter and line-level inputs for easy

incorporation into existing systems, or

as part of a subwoofer/satellite speaker

combination.

Controls for adjusting the volume,

crossover frequency and phase, allow

the subwoofer to be perfectly matched

to any listening environment and audio

components.

The Drivers

To have lots of bass requires moving lots

of air. Your Sunre Subwoofer incorpo-

rates two drivers that can move back and

forth approximately ve times more than

a normal subwoofer. This gives it a lot

of air moving capacity which allows for

majestic bass performance.

Two drivers share the acoustic output.

Sometimes one driver appears to be

moving more than the other. They both

move the same amount only when op-

erating at the limit of their excursion and

power output, or when bass requirements

and music requirements demand maxi-

mum output from the system. Otherwise,

the power is shared between the two

drivers in a way that depends on the mo-

mentary amplitude and the momentary

musical spectrum. It is normal for one or

the other to move more or less than its

mate during operation.

The Amplier

The large movement range of the driv-

ers creates greater air pressure inside

the box than a conventional subwoofer.

Therefore, the drive amplier must be

much more powerful than an ordinary

subwoofer amplier. In fact, it has to be

so powerful, it is almost hard to believe.

The power amplier within your Sunre

Subwoofer is capable of delivering over

1400 watts into a 3.3 ohm resistor (the

driver voice coil resistance). When the

same full output is applied to the driver,

however, the enormous back-electro-

motive force generated as a conse-

quence of its large motion and giant mag-

net, causes the current ow to be much

less than if it were a 3.3 ohm resistor. It

is this singular property of the driver that

allows the subwoofer to be approximately

ten times more efcient than a subwoofer

this size would normally be.

A compressor circuit kicks in automati-

cally if the input signal level reaches a

level that would overload the driver. This

maintains a ceiling on the output without

clipping. If the input signal is driven even

further, a ‘soft clipping’ circuit is enabled.

This allows the subwoofer to put more

sound into the room to satiate the power

hungry user, but without distortion or

damage to the subwoofer. Thus, for ex-

plosive scenes in movies, this produces

extremely high sound pressure levels

(SPL) in your room without the drivers

banging against the mechanical stops.

For more details of the subwoofer design,

please call us or view our website: www.

sunre.com.

Overview

1. Crossover Frequency

This control changes the high fre-

quency cutoff point. With the control set

to 100 Hz, the sub woof er will reproduce

fre quen cies up to 100 Hz. If the control

is set fully clockwise, the crossover is

bypassed and the subwoofer will re-

pro duce a wide frequency range. With

the control fully counter-clock wise the

sub woof er re pro duc es a narrow range,

up to 30 Hz.

Rotate the control until the bass sounds

natural. If the mid-bass sounds natural

but you want more low bass, turn this

control down a little, then turn the

Volume control up by about the same

amount. This increases the low-bass

output while leaving the mid-bass

output the same.

2. Level

This control lets you match the output

level of the subwoofer to the level of

your other speak ers. The subwoofer

output will increase as this control is

rotated clockwise. When you have just

installed your system, turn this down

before turning on your sub woof er. This

will prevent any loud surprises.

3. Phase Control

This control changes the relative phase

of the sub woof er with respect to the

other speakers. Use this control to help

blend the sub woof er with the rest of

the sys tem. This is accomplished by

ad just ing the control in small in cre -

ments as you listen for the most bass

at your lis ten ing position. As a  nal trim,

readjust the Crossover Frequency and

Volume controls after the Phase has

been set.

4. Trigger Input

The trigger input can be used to

automatically turn on the subwoofer

from Standby mode. To do this,

connect +12 VDC to the posi-

tive (+) terminal, and ground to the

negative (–) terminal. Home Theater

preampli ers such as the Sun re

Theater Grand series, have matching

12 VDC Trigger outputs. When they are

turned on, the subwoofer will turn on.

User's Manual

Control Panel Features

5. Line-Level Inputs

Connect these unbalanced inputs with

RCA type patch cords to the line-level

outputs of your receiver or preamp.

If your preamplier or receiver has a

single sub/LFE output, connect it to

either input jack (see page 14).

6. Line-Level Outputs

Line-level output signals are avail-

able at these jacks. These outputs are

active whenever a signal is hooked

up to the inputs of the subwoofer. The

outputs are not affected by the volume

level, phase, frequency control, or EQ

of the subwoofer.

To use the outputs, connect the preamp

outputs on your preamp/receiver to

the subwoofer’s line-level inputs using

good quality RCA type patch cords.

Then connect a second set of patch

cords from these subwoofer outputs

to the line-level inputs of your main

amplier.

The adjacent Output Switch (7) allows

the outputs to be either high-pass, or

full range, see below.

7. Output Switch

This switch affects the frequency range

of the line-level outputs.

In the Bypass position, the outputs are

a full-range copy of the input signals.

In the 85 Hz position, the outputs are

a copy of the input signals with the

frequencies below 85 Hz removed. We

recommend using this position if your

speakers are not designed to repro-

duce low frequencies.

If your main speakers are capable

of operating full range, then use the

Bypass position.

8. Slave Input and Output

These connections simplify the

hookup and operation of two ATMOS

subwoofers.

Connect the slave output from the rst

subwoofer to the slave input of the sec-

ond. This second subwoofer will then

receive the optimum audio signals from

the rst, and there is no need to adjust

the controls of the second subwoofer,

as the audio is controlled by the con-

trols and EQ setting of the rst.

The second subwoofer will not require

any connections to its line-level inputs,

as it receives the audio through its

slave input.

9. Power Switch

The power switch is used for installing

and uninstalling the subwoofer, and for

power conservation during long vaca-

tions. Leave it switched on at all times

for normal operation.

After a period of inactivity (i.e. with no

input signal), the subwoofer will auto-

matically turn itself to Standby mode,

where it is effectively muted. It can turn

back on automatically when an input

signal is applied, or if a 12 VDC trigger

voltage is applied to the Trigger inputs,

or if the Start button is pressed.

10. IEC Linecord socket

The subwoofer comes with a detach-

able linecord that connects here.

US (120 VAC) MODEL: Connect

the linecord to the subwoofer be-

fore connecting the other end to a

120 Volt, 60 Hz AC outlet. The outlet

must have a circuit rating of 8 amps or

more (a typical home circuit is rated at

15 amps).

Never plug the US (120 VAC)

Model subwoofer directly into

220-240 Volts AC as this will

cause catastrophic circuit failure.

continued..

User's Manual

Control Panel Features continued

10. (continued)

EURO (230 VAC) MODEL: Connect

the linecord to the subwoofer before

connecting the other end to a 230 Volt,

50/60 Hz AC outlet. The outlet must

have a cir cuit rating of 6 amps or more.

Never plug the EURO (230 VAC)

model subwoofer directly into

120-130 Volts AC.

11. Line Fuse

The subwoofer is supplied with a con-

ser va tive slow-blow type fuse to protect

the elec tron ics.

Always unplug the power cord

before inspecting or changing

the fuse. Never use a fuse with a

larger current rating than shown

on the markings next to the fuseholder.

12. EQ LED

This LED provides feedback during the

EQ procedure. It also lights continu-

ously whenever the subwoofer is not in

standby.

13. Start button

Used to calibrate the EQ. See page

12 for details on the EQ calibration

procedure.

14. EQ ON/OFF Switch

This switch is used to turn the EQ on

or off. It allows you to easily judge

the effect of the EQ on the subwoofer

performance.

15. Microphone Input

This is the input connection for the

supplied linear measurement micro-

phone used during the automatic EQ

procedure. See page 12 for details of

the EQ procedure.

16. POWER LED

This red LED indicates when the

subwoofer is connected to AC Power.

When a 12 volt trigger voltage or an

audio signal is applied, this LED goes

out and the blue EQ LED lights up.

User's Manual

Installation

Observe the following general precau-

tions and read the safety instructions on

pages 2 and 3 before using your Sunre

Subwoofer.

• Never open the cabinet or remove

the metal control panel as this

might result in an electrical shock to

you, or damage to the unit.

• Protect it from prolonged exposure

to direct sunlight and other direct

sources of heat, such as heating

vents and radiators.

• To prevent re or shock, do not

expose the unit to rain or moisture.

If uid or a foreign object should

enter the unit, immediately turn off

the power and contact your Sunre

Dealer.

• Avoid excessive exposure to

extreme cold or dust.

• Do not place heavy objects on top

of the unit.

• Do not place the subwoofer with its

control panel against the oor.

• To move the subwoofer along the

oor, rotate it onto one edge onto a

plastic sheet or bag, and it will slide

along easier.

Heat rise

• Allow adequate ventilation around

the metal control panel of the

subwoofer.

• Do not let anything come into

contact with the panel and keep

at least two inches away from any

walls.

The metal bottom plate serves as the

amplier heat sink and also as a conduit

to remove internal heat to the outside

and into the atmosphere. It can reach

temperatures of 60 degrees C, which

will feel hot to the touch, using nerves of

esh and blood as temperature sen-

sors. As uncomfortable as it may feel, 60

degrees C cannot burn you, and in fact is

almost cool to copper, silicon, steel, and

aluminum, the materials from which your

subwoofer is constructed.

AC Power Considerations

Ensure that the unit is plugged into an

outlet capable of supplying the correct

voltage specied for your model.

Unplug your subwoofer’s power cord

from the electrical outlet if it will be left

unused for a long period of time.

Route the power-supply cord so it is not

likely to be walked on or pinched by items

placed upon or against it, especially at

plugs, convenience receptacles, and the

point where it exits from the unit.

Magnetic Fields

We recommend that you place your

subwoofer further than two feet away

from your TV, VCR, tape deck or com-

puter, so the speaker’s magnet won’t

distort the colors of your TV picture or

erase your video tapes, audio tapes or

computer discs.

User's Manual

Please consider the following when set-

ting up your new system :

• Before making or changing any

connec tions, ALWAYS make sure

that the subwoofer and your other

components are turned OFF. Also

turn down the volume control of the

subwoofer and your preamplier or

receiver.

• This diagram shows all the low

power components sharing a power

strip which is connected to the same

outlet used by the amplier.

• The subwoofer is connected to an

outlet on the same circuit breaker,

provided that the total system

current draw does not exceed the

breaker current rating.

• This arrangement will reduce the

possibility of an audible hum in your

system caused by a ground loop.

• Whenever possible, keep the

power cords away from the signal

cables or speaker wires to prevent

any hum or interference being

heard in the speakers.

• Choose reliable, high quality inter-

connect cables, also called patch

cords or RCA cables. They should

be fully shielded and as short as

possible for the job. The longest

cable in your system will likely be to

the subwoofer, so choose a good

quality brand.

• Some patch cords can be a very

tight t and there is usually a

preferred method of getting them

off. Some have to be removed with

a twisting action. Be gentle or you

may damage the jacks of the sub-

woofer or your other components.

Connections

User's Manual

Your subwoofer is designed to be placed

in a corner and this will produce optimum

performance.

#1 is very good positioning.

#2 is also excellent but may shake

the back wall too much and cause

things on or along the wall to rattle

too much. If this occurs, use the #3

position:

#3 Move the subwoofer approximately

three feet away from the right wall

and place it along the back wall

as shown. This will substantially

reduce the rattling of the back wall

and will still pressurize the room

with lots of bass.

Experiment with at least two corners and

decide which is the best, or you can try

the following procedure:

1. Start by placing the subwoofer right

on the seat of your favorite couch

or easy chair. Take care to position

it so it is not likely to fall off. (This

method may seem a bit odd, but it

is based on principles of acoustic

physics.)

2. If you are using the subwoofer as

part of a Home Theater system,

you can either run a calibration

test (noise) signal through the

subwoofer, or simply plug the

analog outputs of a CD player di-

rectly into the subwoofer’s line-level

inputs. Turn down the subwoofer's

volume level before turning on the

CD, then play some of your favorite

music samples with heavy bass.

Location

3. Walk around the room, listening,

and stand in all the positions where

you might be able to place the

subwoofer. Try crouching down,

and try the corners. Find the place

where the subwoofer's bass output

sounds the loudest.

4. Shut things down and install the

subwoofer in this position. Make

sure the control panel is not touch-

ing anything, and that it can receive

good ventilation.

Although low frequencies are non-direc-

tional, factors such as room reections,

standing waves, resonance and absorp-

tion will strongly affect your subwoofer’s

performance. Moving the subwoofer from

one location to another can have a major

effect on the bass response.

The Auto EQ mode will let you adjust for

the room effects, but you should nd the

best location rst.

Remember to keep the subwoofer

at least two or three feet away from

any TV screen, computer, VCR or

magnetic tapes and discs. This will

reduce the chance of the magnetic elds

upsetting the TV screen or erasing your

magnetic media.

Using Two Subwoofers

If you wish to use two subwoofers, the

sound output will double (an increase of

3 dB). Locate the subwoofers with one

in each corner and experiment with the

location and phase control to achieve the

best bass response.

Use the Slave input and output con-

nections if you are using two ATMOS

subwoofers.

User's Manual

Subwoofer performance is greatly af-

fected by the room in which it is situated,

and the positioning within the room. The

room effects will boost and cut the output

levels reaching your listening position.

This gives a "Room EQ" effect which can

often be far from wonderful.

The Sunre ATMOS can automatically

adjust for the effects of Room EQ. It

measures the actual frequency response

using the supplied measurement micro-

phone. Then it automatically compen-

sates for peaks or dips and smooths out

the response.

For best results it is recommended that

the subwoofer crossover in your receiver

or processor be set to its maximum set-

ting (or “bypass”). This ensures that the

subwoofer will be properly matched to the

rest of the speakers in your system.

The following procedure will help you

start the automatic equalization:

Procedure

1. Install the subwoofer in the best location

you can nd (see previous page).

2. The calibration must be done while the

listening room is quiet. Please turn off

any noisy machinery, including heating

or cooling systems during this process.

Have the kids play in the backyard and

give the dog a treat to have him stop

barking. A small amount of noise, such

as quiet talking or whispering, is OK.

Room Equalization Procedure

3. Place the microphone in the listening

position (on the couch, for example),

pointing in the direction you’ll normally

be facing while listening to your system.

Only use the microphone supplied by

Sunre.

4. Plug the microphone into the subwoof-

er's microphone jack.

5. Set these controls:

• Volume to 0 dB.

• Crossover to "Bypass."

• Phase to "0."

• EQ ON/OFF switch to ON

6. Avoid making noise during this proce-

dure. Turn on the subwoofer AC power

switch. Next, press the START button for

ve seconds to enter calibration mode.

You will hear a loud low rumble sound

coming from the subwoofer.

7. After about 10 seconds press the

START button again and sound will

come from the subwoofer at a different

frequency.

8. Wait another 10 seconds and press the

START button again. A new frequency

will come from the subwoofer.

9. You’ll need to wait another 10 seconds

and then press the START button

again. A fourth tone will come from the

subwoofer.

10. Finally, after another 10 seconds press

the START button again and hold it until

the sound stops. Your Atmos subwoofer

is now equalized to your room.

User's Manual

11. Unplug the microphone and store it in a

safe place.

12. Finish the setup by adjusting the Atmos

VOLUME, CROSSOVER and PHASE

appropriately and calibrating your

surround sound receiver/processor

according to its owner’s manual.

13. If you add/remove heavy draperies or

large furniture or move the Atmos to a

new acoustic environment repeat steps

6-12.

Resetting the EQ

1. Turn off the subwoofer using the AC

power switch.

2. Hold down the Start button and turn on

the AC power switch.

3. Keep the Start button held down for 10

seconds while the blue EQ LED ashes.

4. When the LED goes out, the EQ is reset

to the at factory setting.

Using Two Subwoofers

1. If you are using two ATMOS subwoofers,

make sure that they are connected us-

ing the SLAVE output of the rst sub to

the SLAVE input of the second.

2. Connect the microphone to the rst

ATMOS subwoofer only.

3. Follow the procedure on the previous

page. The EQ room measurement will

take into account the sound from both

subwoofers, and the EQ adjustment will

affect both subwoofers.

User's Manual

System Congurations

The following pages show some typical

connections that you might make in your

installation. They show how the inputs

and outputs of the Sunre Subwoofer

are con nected to your preamplier or

receiver.

If your preamplier has a

subwoofer output (often labeled

LFE for Low Frequency Ef-

fects), it can be connected to the

subwoofer’s left or right input as

shown. This is the simplest and

recommended connection. A re-

ceiver with a sub/LFE output can

be connected in the same way.

The subwoofer will play the low

frequency range and the

other speakers will play

the frequency range

delivered to them by

your amplier.

If you have a Home

Theater preamplier, it

may have an inde-

pendent subwoofer

volume control. Make

sure this is correctly

adjusted, and that the

Sunre Subwoofer’s

crossover frequency is

set to 100 Hz. This is

by no means an iron-

clad rule, rather it is

a good starting point.

(See the crossover fre-

quency control details

on page 6 and adjustments on page 18).

You can set the subwoofer’s level control

to 0 dB, and then use the preamplier’s

subwoofer level control for normal and

routine adjustments.

Connections to a preamplier’s subwoofer output

User's Manual

If your preamplier does not have

a dedicated sub/LFE output, you

can use “Y” cables to send its

main outputs to both the sub-

woofer and your amplier.

The subwoofer will play the low

frequency range and your front

speakers will play the full range.

Although bass is commonly dis-

tributed evenly between left and

right channels (L+R bass), movie

soundtracks often contain dif-

ferential (L-R) bass. The opening

scene in “Top Gun”, for example,

has loads of L-R bass

information. If this

is not preserved,

the bass in these

scenes sounds

anemic. Therefore,

systems which do

not have a dedicated

sub/LFE output

should use both

the left and the right

inputs as shown, for

the greatest bass

impact.

An alternative con-

nection method without us-

ing Y cables is shown on the next page.

If your preamp/receiver has a dedicated

sub/LFE output, then only one input is

used as shown on the previous page.

Connections to a preamplier using Y cables

User's Manual

If you are using a preamplier

that does not have a sub/LFE

output, you can send its left

and right front output into

the subwoofer’s line-level

inputs and then connect the

subwoofer’s line-level outputs

to the inputs of your amplier.

The subwoofer will play the

low frequencies and your

amplier and front speak-

ers will play the frequency

range of the subwoofer's

outputs.

The subwoofer's

output switch lets

you select BYPASS

or 85 Hz.

In the 85 Hz posi-

tion, the signals

coming out of the

subwoofer’s outputs

are a copy of the

signals going into

the subwoofer,

except that the

low bass is ltered

out. This uses

the subwoofer’s

passive crossover

network, rather than

the active network

and controls. This

is an excellent

method if your front speakers are

small satellites or mini-monitors, and/or

your power amplier is of limited power,

such as a tube amp.

If the switch is set to BYPASS, then the

amplier and speakers receive the full

frequency range. This is a good position

if your speakers are capable of good low

frequency performance.

Using the line-level outputs

User's Manual

The SLAVE output from one

ATMOS subwoofer can be con-

nected to the SLAVE input of a

second ATMOS subwoofer. The

second subwoofer will then re-

ceive the optimum audio signals

from the rst.

There is no need to adjust

the controls of the second

subwoofer, as the audio is con-

trolled by the controls and EQ

setting of the rst. The second

subwoofer does not require

any connections to its line-level

inputs.

Before the EQ procedure,

make sure that both ATMOS

subwoofers are connected

together as shown. The micro-

phone should be connected

to the rst subwoofer. The

automatic EQ procedure will

take into account the effect of

both subwoofers as they play in

the room.

Using the slave input and output

User's Manual

There are two main methods for adjust-

ing the level, crossover frequency and

phase of the Sunre Subwoofer to match

a system:

• Bob Carver’s preferred method:

By listening and making the

adjustments to suit your taste.

• Laboratory method: By measuring

the output and adjusting for a at

frequency response.

Excellent results can be obtained if you

make the adjustments based on simply

listening. This is Sunre’s preferred meth-

od as it allows the system to be voiced

based on what sounds the best, whereas

laboratory-at frequency response can

often be clinical and less than exciting.

The following procedure is for those who

prefer a more methodical and scientic

approach. This excerpt is from “The

Audio Critic,” issue 24, page 31, written

by contributing editor David Rich, and is

reprinted here with their kind permission.

You will need a test CD with low-fre-

quency warble tones, and a sound pres-

sure-level meter. The Radio Shack

SPL

meter will do ne, as will the Stereophile

test CD.

“Step 1. Disconnect the subwoofer and

run the main speaker with a tone in its

passband (80-100Hz). Measure the level.

Step 2. Disconnect the main speaker

and reconnect the subwoofer. Set the

subwoofer to its highest crossover

frequency. Set the level control of the

subwoofer to give the same sound pres-

sure level with the same tone you used

in Step 1.

Step 3. With both the subwoofer and

the main speaker connected, measure

the level of the tones at the available

frequencies. Because the crossover

is set too high, you will have a peaked

response. Adjust the crossover control to

get the smoothest response.

Adjusting the controls

Step 4. Use the phase control to make

the response even smoother. It has its

biggest effect at the crossover frequency.

You can iterate between the crossover

and the phase controls. Keep your hands

off the level control! It was set correctly

in step 2.

Step 5. Listen to the subwoofer. Resist

all temptations to turn up the level

control. Play something with really deep

bass to conrm that your subwoofer is

working.”

Control settings

Use this drawing to record some of your

favorite settings.

User's Manual

Specications

Amplier Output

1400 watts rms (3.3 Ω impedance)

High Cut Filter

30 Hz - 100 Hz adjustable, with a

"Bypass" position.

Frequency Response

30 Hz - 100 Hz

Power Line Voltage

US model

100-120 VAC 50/60 Hz

Fuse Rating 6A slow blow

International model

220-240 VAC 50/60 Hz

Fuse Rating 4A slow blow

Dimensions

Height 8.5 inches (21.6 cm)

Width 8.9 inches (22.6 cm)

Length 10.1 inches (25.7 cm)

Weight

32 lbs (14.5 kg)

Line Power Consumption:

330 watts average, at maximum continu-

ous output. 0.5 watts at idle.

1400 watts peak, time limited basis

Output Levels:

Greater than 106 dB peak SPL (includes

room gain) from 35 Hz to 80 Hz. Mea-

surement is one meter, anechoic.

A typical Sunre subwoofer can be

expected to beat its specied minimum

peak SPL by several decibels.

Total Harmonic Distortion

Typically less than 1/10 of the funda-

mental between 18 to 80 Hz.

Input Sensitivity (full output):

150 mVrms for full output with volume

control at maximum, 600 mVrms with

volume control at middle(0dB), no output

with volume control at minimum.

Input Impedance:

30 kΩ Line-Level Inputs

Driver: 6.5 inch

Extra large magnet and long throw

mechanical design yield very high

back-emf. The result is extraordinarily

high operating efciency – that is, more

acoustic output for each watt of input.

Internal System Gain:

50 dB from input jack to speaker with

volume control at 0 dB, 62 dB with con-

trol fully clockwise.

12 VDC Trigger Input

Input voltage range: 5 -18 VDC

Impedance: approx 600 Ω

(20 mA @ 12 V)

Removable terminal block.

Group LLC.

right to improve its products at any time.

Therefore, specications are subject to

change without notice.

User's Manual

La page charge ...

Sunfire Atmos XTATM265 Manuel utilisateur

Marque: Sunfire

Modèle: Atmos XTATM265

Catégorie: Subwoofers

Taper: Manuel utilisateur

Ce manuel convient également à

Atmos XTATM265230

Télécharger le PDF

rapport

dans d''autres langues

English: Sunfire Atmos XTATM265 User manual

Sunfire Atmos XTATM265 Manuel utilisateur

Ce manuel convient également à

Sunfire Atmos XTATM265 Manuel utilisateur

dans d''autres langues

Autres documents