Dell Projector 1100MP Manuel utilisateur

www.dell.com | support.dell.com

Dell™ 1100MP Projector

Owner’s Manual

Notes, Notices, and Cautions

NOTE: A NOTE indicates important information that helps you make better use

of your projector.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of

data and tells you how to avoid the problem.

CAUTION: A CAUTION indicates a potential for property damage, personal

injury, or death.

____________________

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly

forbidden.

Trademarks used in this text: Dell and the DELL logo are trademarks of Dell Inc.; DLP and

Texas Instruments are trademarks of Texas Instruments Corporation; Microsoft and Windows are

registered trademarks of Microsoft Corporation; Macintosh is a registered trademark of Apple

Computer, Inc.

Other trademarks and trade names may be used in this document to refer to either the entities

claiming the marks and names or their products. Dell Inc. disclaims any proprietary interest in

trademarks and trade names other than its own.

Restrictions and Disclaimers

The information contained in this document, including all instructions, cautions, and regulatory

approvals and certifications, is based upon statements provided to Dell by the manufacturer and

has not been independently verified or tested by Dell. Dell disclaims all liability in connection

with any deficiencies in such information.

All statements or claims regarding the properties, capabilities, speeds, or qualifications of the

part referenced in this document are made by the manufacturer and not by Dell. Dell specifi-

cally disclaims any knowledge of the accuracy, completeness, or substantiation for any such

statements.

____________________

February 2006 Rev. A02

Contents 3

Contents

1 Your Dell™ Projector

About Your Projector . . . . . . . . . . . . . . . 6

2 Connecting Your Projector

Connecting to a Computer . . . . . . . . . . . . . . 8

Connecting a DVD Player, Set Top Box, VCR, or TV

. . . 8

Connecting With a Component Cable

. . . . . . . 8

Connecting With an S-Video Cable

. . . . . . . . 9

Connecting With a Composite Cable

. . . . . . . 9

Connecting to a Wired RS232 Remote Control

. . . . . 9

Connecting to a Computer

. . . . . . . . . . . . 10

Connecting With a Commercial RS232

Control Box

. . . . . . . . . . . . . . . . . . . 10

3 Using Your Projector

Turning Your Projector On . . . . . . . . . . . . . . . 11

Turning Your Projector Off

. . . . . . . . . . . . . . 11

Adjusting the Projected Image

. . . . . . . . . . . . 12

Raising the Projector Height

. . . . . . . . . . . 12

Lowering the Projector Height

. . . . . . . . . . 12

Adjusting Projection Image Size

. . . . . . . . . . . 13

4 Contents

Adjusting the Projector Zoom and Focus . . . . . . . 14

Using the Control Panel

. . . . . . . . . . . . . . . 15

Using the Remote Control

. . . . . . . . . . . . . . 16

Using the On-Screen Display

. . . . . . . . . . . . 17

Main Menu

. . . . . . . . . . . . . . . . . . . 18

All Images Menu

. . . . . . . . . . . . . . . . 18

Audio Menu

. . . . . . . . . . . . . . . . . . 19

Management Menu

. . . . . . . . . . . . . . . 20

Language Menu

. . . . . . . . . . . . . . . . 21

Factory Reset Menu

. . . . . . . . . . . . . . 21

Computer Image Menu

. . . . . . . . . . . . . 21

Video Image Menu

. . . . . . . . . . . . . . . 22

4 Troubleshooting Your Projector

Changing the Lamp . . . . . . . . . . . . . . . . . 26

5 Specifications

6 Contacting Dell

7 Glossary

Your Dell™ Projector 5

Your Dell™ Projector

Your projector comes with all the items shown below. Ensure that you have all the

items, and contact Dell if anything is missing.

Package Contents

Power cable (1.8m) VGA cable (D-sub to D-sub) (1.8m)

S-Video cable (2.0m) USB cable (1.8m)

Composite cable (1.8m) VGA to component cable (1.8m)

RCA to audio cable (1.8m) Mini pin to Mini pin cable (1.8m)

NOTE: Cable lengths are for the Americas only.

www.dell.com | support.dell.com

6 Your Dell™ Projector

About Your Projector

Remote control Batteries

Carrying Case Documentation

1 Control panel

2 Zoom tab

3 Focus ring

4 Lens

5 Elevator button

6 Remote control receiver

Package Contents (continued)

1

2

3

456

Connecting Your Projector 7

Connecting Your Projector

1 IR receiver

2 VGA out (monitor loop-through)

3 USB connector

4 RS232 connector

5 VGA in (D-sub) connector

6 S-video connector

7 Composite video connector

8 Audio input connector

21345678

www.dell.com | support.dell.com

8 Connecting Your Projector

Connecting to a Computer

NOTE: The USB cable must be connected if you want to use the Next Page and

Previous Page features on the remote control.

Connecting a DVD Player, Set Top Box, VCR, or TV

Connecting With a Component Cable

1 Power cord

2 VGA to VGA cable

3 USB to USB cable

1 Power cord

2 D-sub to HDTV/Component cable

1

2

3

2

1

Connecting Your Projector 9

Connecting With an S-Video Cable

Connecting With a Composite Cable

Connecting to a Wired RS232 Remote Control

NOTE: The RS232 cable is not provided by Dell. Consult a professional installer

for the cable and RS232 remote control software.

1 Power cord

2 S-video cable

1 Power cord

2 Composite video cable

1

2

1

2

www.dell.com | support.dell.com

10 Connecting Your Projector

Connecting to a Computer

Connecting With a Commercial RS232 Control Box

1 Power cord

2 RS232 cable

1 Power cord

2 RS232 cable

3 Commercial RS232 control box

1

2

1

2

3

Using Your Projector 11

Using Your Projector

Turning Your Projector On

NOTE: Turn on the projector before you turn on the source.The Power button

light blinks green until pressed.

1

Remove the lens cap.

2

Connect the power cord and appropriate cables. For information about

connecting the projector, see "Connecting Your Projector" on page 7.

3

Press the Power button(see "About Your Projector" on page 6 to locate the Power

button). The Dell logo displays for 30 seconds.

4

Turn on your source (computer, DVD player, etc.). The projector automatically

detects your source.

NOTE: Allow the projector some time to search for the source.

If the "Searching..." message appears on the screen, ensure that the

appropriate cable(s) are securely connected.

If you have multiple sources connected to the projector, press the Source button

on the remote control or control panel to select the desired source.

Turning Your Projector Off

NOTICE: Do not unplug the projector before properly shutting down as

explained in the following procedure.

1

Press the Power button.

2

Press the Power button again. The cooling fans continues to operate for 90

seconds.

3

Disconnect the power cord from the electrical outlet and the projector.

NOTE: If you press the Power button while the projector is running, the

following message appears:

" Press Power button to Turn Off Projector.Projector

must cool down for 90 seconds before unplugging or

restarting." The message disappears in 5 seconds or you can press any

button on the control panel.

www.dell.com | support.dell.com

12 Using Your Projector

Adjusting the Projected Image

Raising the Projector Height

1

Press the elevator button.

2

Raise the projector to the desired display angle, and then release the button to

lock the elevator foot into position.

3

Use the tilt adjustment wheel to fine-tune the display angle; if necessary, press the

side elevator buttons to raise the rear side of the projector to the desired display

angel.

Lowering the Projector Height

1

Press the elevator button.

2

Lower the projector, and then release the button to lock the elevator foot into

position.

1 Elevator button

2 Elevator foot

3 Tilt adjustment wheel

1

3

2

Using Your Projector 13

33.0"(83.8cm)

55.0"(139.7cm)

110.0"(279.4cm)

165.0"(419.1cm)

220.0"(558.8cm)

275.0"(698.5cm)

Projector to screen distance

3.9'(1.2m)

27.5"

(69.8cm)

45.8"

(116.3cm)

91.7"

(232.9cm)

137.5"

(349.3cm)

183.4"

(465.8cm)

229.2"

(582.2cm)

6.6'(2.0m)

13.1'(4.0m)

19.7'(6.0m)

26.2'(8.0m)

32.8'(10.0m)

Adjusting Projection Image Size

Screen

(Diagonal)

Max.

33.0" (83.8cm) 55.0"(139.7cm) 110.0"(279.4cm) 165.0"(419.1cm) 220.0"(558.8cm) 275.0"(698.5cm)

Min.

27.5"(69.8cm) 45.8"(116.3cm) 91.7"(232.9cm) 137.5"(349.3cm) 183.4"(465.8cm) 229.2"(582.2cm)

Screen

size

Max.

(WxH)

26.4"x19.8" 44.0"x33.0" 88.0"x66.0" 132.0"x99.0" 176.0"x132.0" 220.0"x165.0"

67.1cm x50.3cm 111.8cmx83.8cm 223.5cmx167.6cm 335.3cmx251.5cm 447.0cmx335.3cm 558.8cmx419.1cm

Min.

(WxH)

22.0"x16.5" 36.7"x27.5" 73.3"x55.0" 110.0"x82.5" 146.7"x110.0" 183.4"x137.5"

55.9cmx41.9cm 93.2cmx69.8cm 186.2cmx139.7cm 279.4cmx209.6cm 372.6cmx279.4cm 465.8cmx349.3cm

Distance

3.9ft(1.2m) 6.6ft(2.0m) 13.1ft(4.0m) 19.7ft(6.0m) 26.2ft(8.0m) 32.8ft(10.0m)

*This graph is for user reference only.

www.dell.com | support.dell.com

14 Using Your Projector

Adjusting the Projector Zoom and Focus

CAUTION: To avoid damaging the projector, ensure that the zoom lens and

elevator foot are fully retracted before moving the projector or placing the

projector in its carrying case.

1

Rotate the zoom tab to zoom in and out.

2

Rotate the focus ring until the image is clear. The projector focuses at distances

from 3.9ft to 32.8ft (1.2m to 10m).

3

1 Zoom tab

2 Focus ring

1

2

Using Your Projector 15

Using the Control Panel

1 Power Turn the projector on and off. For more information,

see "Turning Your Projector On" on page 11 and

"Turning Your Projector Off" on page 11.

2 Source Press to toggle through Analog RGB, Composite,

Component-i, S-video, and Analog YPbPr sources when

multiple sources are connected to the projector.

3 Four Directional

Keys

The four directional keys can be used to

toggle through the tabs in the OSD.

4 TEMP warning light

• If the Temp light is solid orange, the projector has

overheated. The display automatically shuts down.

Turn the display on again after the projector cools

down. If the problem persists, contact Dell.

• If the Temp light is blinking orange, a projector fan

has failed and the projector automatically shuts down.

If this problem persists, contact Dell.

5 LAMP warning light

If the Lamp light is solid orange, replace the lamp.

6 Keystone adjustment If your image is not perpendicular to the screen, then it

does not appear square. Press to adjust image distortion

caused by tilting the projector. (±16 degrees)

7 Resync Press to synchronize the projector to the input source.

Resync does not operate if the on-screen display (OSD)

is displayed.

4

5

6

7

8

3

2

1

www.dell.com | support.dell.com

16 Using Your Projector

Using the Remote Control

8 Menu Press to activate the OSD. Use the directional keys and

the Menu button to navigate through the OSD.

1 Video Mode Press once to show the current display mode.

Press the button again to toggle between PC,

Movie, sRGB, or User mode.

2 Next Page Press to move to the next page.

NOTE: The USB cable must be connected to

use this function.

3 Menu Press to activate the on-screen display (OSD).

Use the directional keys and the Menu button to

navigate through the OSD.

4 4:3/16:9 Press to switch the apect ratio: 1:1, 16:9, 4:3.

5 Hide button Press to hide the image, press again to display the

image.

6 Volume +/- Press to increase (+) or decrease (-) the volume

or toggle through the OSD tabs.

Using Your Projector 17

Using the On-Screen Display

The projector has a multi-language On-Screen Display (OSD) that can be

displayed with or without an input source present.

In the Main Menu, press the or button on the control panel or the  or 

button on the remote control navigate through the tabs. Press the button on

the control panel or the Menu button on the remote control to select a submenu.

In the submenus, press the or button on the control panel or the  or 

button on the remote control to make a selection. When an item is selected, the

color changes to dark gray. Use the or button on the control panel or the 

and  button on the remote control make adjustments to a setting.

To exit the OSD, go to the Exit tab and press the button on the control panel

or the Menu button on the remote control.

7 Keystone adjustment If your image is not perpendicular to the screen,

then it does not appear square. Press to adjust

image distortion caused by tilting the projector

(±16 degrees).

8 Resync Press to synchronize the projector to the input

source. Resync does not operate if the OSD is

displayed.

9 Source Press to toggle through Analog RGB, Composite,

Component-i, S-video, and Analog YPbPr sources

when multiple sources are connected to the

projector.

10 Directional keys Use the  or  button to select OSD items, use

the  and  button to make adjustments.

11 Previous Page Press to go to the previous page.

NOTE: The USB cable must be connected to

use this function.

12 Power Turn the projector on and off. For more

information, see "Turning Your Projector On" on

page 11 and "Turning Your Projector Off" on

page 11.

www.dell.com | support.dell.com

18 Using Your Projector

Main Menu

All Images Menu

BRIGHTNESS—Use

and button on the

control panel or the

 or 

button on the

remote control to

adjust the brightness of the

image.

C

ONTRAST—Use

and button on the

control panel or the

 or 

button on the

remote control

the degree of difference

between the brightest and darkest parts of

the picture. Adjusting the contrast changes

the amount of black and white in the image.

C

OLOR TEMP—Adjust the color temperature.

The higher the temperature, the bluer screen

appears; the lower the temperature, the

screen redder the screen appears.

User mode activates the values in the color setting menu.

C

OLOR SETTING—Manually adjust red, green, and blue color.

K

EYSTONE—Adjust the image distortion caused by tilting the projector (

±16

degrees).

AUTO KEYSTONE—

Select

Ye s

to enable the auto correction for vertical image distortion

caused by tilting the projector. To manually adjust the keystone, press the button

on the control panel or the Menu button on the remote control.

Using Your Projector 19

SEM-AUTO KEYSTONE—

Press the

button on the control panel or the Menu button

on the remote control, the

Auto Keystone

will do once.

ASPECT RATIO—Select an aspect ratio to adjust how the image appears.

• 1:1 — The input source displays without scaling.

Use 1:1 apect ratio if you are using one of the following:

– VGA cable and the the computer has a resolution less than XGA (1024 x 768)

– Component cable (576p/480i/480p)

– S-Video cable

– Composite cable

• 16:9 — The input source scales to fit the width of the screen.

• 4:3 — The input source scales to fit the screen.

Use 16:9 or 4:3 if you are using one of the following:

– Computer resolution greater than XGA

– Component cable (1080i or 720p)

VIDEO MODE—Select a mode to optimize the display image based on how the

projector is being used: Movie, PC, sRGB (provides more accurate color

representation), and User (set your preferred settings). If you adjust the settings

for White Intensity or Degamma, the projector automatically switches to User.

W

HITE INTENSITY—Select 0 to maximize the color reproduction and 10 to maximize

the brightness.

D

EGAMMA—Adjust between 1 and 6 to change the color performance of the display.

The default setting is 0.

Audio Menu

VOLUME—

Press the button on the control

panel or the - button on the remote control to

decrease the volume and press the

button on

the control panel or the + button on the remote

control to increase the volume.

MUTE—Allows to mute the volume.

www.dell.com | support.dell.com

20 Using Your Projector

Management Menu

MENU LOCATION—Select the location of the

OSD on the screen.

P

ROJECTION MODE—Select how the image

appears:

• Front Projection-Desktop (the default).

• Rear Projection-Desktop — The

projector reverses the image so you can project

from behind a translucent screen.

• Front Projection-Ceiling Mount — The

projector turns the image upside down for

ceiling-mounted projection.

• Rear Projection-Ceiling Mount — The

projector reverses and turns the image upside

down. You can project from behind a

translucent screen with a ceiling-mounted

projection.

SIGNAL TYPE—Manually select the signal type (RGB, YCbCr, or YPbPr)

L

AMP HOUR—Displays the operating hours since the last timer reset.

L

AMP RESET—After you install a new lamp, select Yes to reset the lamp timer.

P

OWER SAVING—Select Yes to set the power saving delay period. The delay period is

the amount of time you want the projector to wait without signal input. After that

set time, the projector enters power saving mode and turns off the lamp. The

projector turns back on when it detects an input signal or you press the Power

button. After two hours, the projector turns off and you need to press the Power

button to turn the projector on.

O

SD LOCK—Select On to enable the OSD Lock for hiding the OSD menu. To

display OSD menu, press the button on the control panel or the Menu button

on the remote control for 15 seconds.

A

UTO SOURCE—Select On (the default) to autodetect the available input signals.

When the projector is on and you press Source, it automatically finds the next

available input signal. Select Off to lock the current input signal. When Off is

selected and you press Source, you select which input signal you want to use.

E

CO MODE—Select On to use the projector at a lower power level (150 Watts),

which may provide longer lamp life, quieter operating, and dimmer luminvance

output on the screen. Select Off to operate at noraml power level (200 Watts).

O

SD TIMEOUT —Use this function to set the duration OSD menu stay active

(at idle state).

La page charge ...

Dell Projector 1100MP Manuel utilisateur

Ce manuel convient également à

Dell Projector 1100MP Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents