Schumacher DSR121 12V 250A ProSeries Battery Charger/Engine Starter DSR122 6/12V 275A ProSeries Battery Charger/Engine Starter DSR123 12/24V 250A ProSeries Battery Charger/Engine Starter DSR124 6/12/24V 330A ProSeries Battery Charger/Engine Starter Le manuel du propriétaire
- Catégorie
- Chargeurs de batterie
- Taper
- Le manuel du propriétaire
0099001943-01
PLEASE SAVE THIS OWNERS MANUAL AND READ BEFORE EACH USE.
This manual will explain how to use the battery charger safely and effectively.
Please read and follow these instructions and precautions carefully.
POR FAVOR CONSERVE ESTE MANUAL DEL USUARIO Y LEALO ANTES
DE CADA USO. En este manual le explica cómo utilizar el cargador de batería
de manera segura y conable. Por favor, lea y siga las siguientes instrucciones
y precauciones.
GARDER LE MANUEL D’INSTRUCTION ET LISEZ LE AVANT CHAQUE
UTILISATION. Ce manuel explique comment utiliser le chargeur de batterie
d’une façon securitaire et efcace. S’il vous plaît lisez et suivez ces instructions
et precautions.
MODELS / MODELOS / MODÈLES :
DSR121, DSR122, DSR123, DSR124
Professional Wheel Charger
Cargador profesional con ruedas
Chargeur professionnel sur roues
OWNERS MANUAL / MANUAL DEL USUARIO / MANUEL D’UTILISATION
DSR124
CONTENTS
IMPORTANT SAFETY INSTRUCTIONS ...................................................................................... 5
PERSONAL SAFETY PRECAUTIONS ......................................................................................... 5
PREPARING TO CHARGE ........................................................................................................... 6
CHARGER LOCATION ................................................................................................................. 6
DC CONNECTION PRECAUTIONS ............................................................................................. 6
FOLLOW THESE STEPS WHEN BATTERY IS INSTALLED IN VEHICLE ................................... 6
FOLLOW THESE STEPS WHEN BATTERY IS OUTSIDE VEHICLE ........................................... 7
GROUNDING AND AC POWER CORD CONNECTIONS ........................................................... 7
ASSEMBLY INSTRUCTIONS ....................................................................................................... 7
CONTROL PANEL ......................................................................................................................... 8
OPERATING INSTRUCTIONS ...................................................................................................... 9
MAINTENANCE AND CARE ....................................................................................................... 12
ERROR CODES AND TROUBLESHOOTING ............................................................................ 13
BEFORE RETURNING FOR REPAIRS ...................................................................................... 15
SPECIFICATIONS ....................................................................................................................... 16
LIMITED WARRANTY ................................................................................................................. 17
WARRANTY CARD ..................................................................................................................... 47
CONTENIDOS
INSTRUCCIONES IMPORTANTES DE SEGURIDAD ................................................................ 18
PRECAUCIONES DE SEGURIDAD PERSONAL ....................................................................... 18
PREPARACIÓN PARA LA CARGA ............................................................................................ 19
UBICACIÓN DEL CARGADOR ................................................................................................... 19
PRECAUCIONES DE CONEXIÓN EN CC ................................................................................. 19
SIGA ESTOS PASOS CUANDO LA BATERÍA ESTÉ COLOCADA EN EL VEHÍCULO .............. 20
SIGA ESTOS PASOS CUANDO LA BATERÍA SE ENCUENTRE FUERA DEL VEHÍCULO ....... 20
CONEXIONES A TIERRA Y ENERGÍA DE CA ........................................................................... 21
INSTRUCCIONES DE MONTAJE ............................................................................................21
PANEL DE CONTROL ................................................................................................................. 22
INSTRUCCIONES DE OPERACIÓN .......................................................................................... 23
MANTENIMIENTO Y CUIDADO ................................................................................................. 27
CÓDIGOS DE ERROR Y LOCALIZACIÓN Y RESOLUCIÓN DE PROBLEMAS ....................... 27
ANTES DE DEVOLVER A REPARACIONES .............................................................................. 30
ESPECIFICACIONES ................................................................................................................. 31
GARANTÍA LIMITADA ................................................................................................................. 32
TARJETA DE GARANTÍA ............................................................................................................ 47
TABLE DES MATIÈRES
CONSIGNES DE SÉCURITÉ IMPORTANTES ........................................................................... 33
MESURES DE SÉCURITÉ PERSONNELLE .............................................................................. 33
PRÉPARATION POUR LE CHARGEMENT ................................................................................ 34
EMPLACEMENT DU CHARGEUR ............................................................................................. 34
PRÉCAUTIONS SUR LA CONNEXION C.C. .............................................................................. 34
ÉTAPES À SUIVRE QUAND LA BATTERIE EST INSTALLÉE DANS UN VÉHCULE ................ 34
ÉTAPES À SUIVRE QUAND LA BATTERIE EST INSTALLÉE HORS DU VÉHICULE ............... 35
MISE À LA TERRE ET CORDON D’ÉNERGIE CA ..................................................................... 35
DIRECTIVES D’ASSEMBLAGE .................................................................................................. 36
PANNEAU DE CONTRÔLE ........................................................................................................ 36
CONSIGNES D’UTILISATION ..................................................................................................... 38
MAINTENANCE ET ENTRETIEN ............................................................................................... 41
CODES D’ÉCHEC ET DÉPANNAGE .......................................................................................... 42
AVANT DE RETOURNER POUR LES RÉPARATIONS .............................................................. 45
SPÉCIFICATIONS ....................................................................................................................... 45
GARANTIE LIMITÉE ................................................................................................................... 46
CARTE DE GARANTIE ............................................................................................................... 48
• 5 •
1. IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS.
1.1 SAVE THESE INSTRUCTIONS –
This manual contains important safety
and operating instructions.
1.2 Keep out of reach of children.
1.3 Do not expose the charger to rain or snow.
1.4 Use of an attachment not recommended
or sold by the battery charger
manufacturer may result in a risk of re,
electric shock or injury to persons.
1.5 To reduce the risk of damage to electric
plug and cord, pull by the plug rather than
the cord when disconnecting charger.
1.6 An extension cord should not be used
unless absolutely necessary. Use of
improper extension cord could result
in a risk of re and electric shock. If an
extension cord must be used, make sure:
• The pins on plug of extension cord are
the same number, size and shape as
those of plug on charger.
• The extension cord is properly wired and
in good electrical condition.
• The wire size is large enough for AC
ampere rating of charger as specied in
section 8.
1.7 Do not operate charger with damaged
cord or plug – replace the cord or plug
immediately.
1.8 Do not operate charger if it has received
a sharp blow, been dropped, or otherwise
damaged in any way; take it to a qualied
serviceman.
1.9 Do not disassemble charger; take it to
a qualied serviceman when service or
repair is required. Incorrect reassembly
may result in a risk of electric shock or re.
1.10 To reduce risk of electric shock, unplug
charger from outlet before attempting
any maintenance or cleaning. Turning off
controls will not reduce this risk.
1.11 WARNING:
RISK OF EXPLOSIVE GASES.
a. WORKING IN VICINITY OF A LEAD-
ACID BATTERY IS DANGEROUS.
BATTERIES GENERATE EXPLOSIVE
GASES DURING NORMAL BATTERY
OPERATION. FOR THIS REASON, IT IS
OF UTMOST IMPORTANCE THAT YOU
FOLLOW THE INSTRUCTIONS EACH
TIME YOU USE THE CHARGER.
b. To reduce risk of battery explosion,
follow these instructions and those
published by battery manufacturer
and manufacturer of any equipment
you intend to use in vicinity of battery.
Review cautionary markings on these
products and on engine.
2. PERSONAL SAFETY PRECAUTIONS
2.1 Consider having someone close enough
by to come to your aid when you work
near a lead-acid battery.
2.2 Have plenty of fresh water and soap
nearby in case battery acid contacts skin,
clothing, or eyes.
2.3 Wear complete eye protection and
clothing protection. Avoid touching eyes
while working near battery.
2.4 If battery acid contacts skin or clothing,
wash immediately with soap and water.
If acid enters eye, immediately ood
eye with running cold water for at least
10 minutes and get medical attention
immediately.
2.5 NEVER smoke or allow a spark or ame
in vicinity of battery or engine.
2.6 Be extra cautious to reduce risk of
dropping a metal tool onto battery. It might
spark or short-circuit battery or other
electrical part that may cause explosion.
2.7 Remove personal metal items such as
rings, bracelets, necklaces, and watches
when working with a lead-acid battery. A
lead-acid battery can produce a short-
circuit current high enough to weld a ring
or the like to metal, causing a severe burn.
2.8 Use charger for charging only LEAD-
ACID (STD, AGM or GEL) rechargeable
batteries with rated capacities of 24Ah
(6V) and 22-59Ah (12V). It is not intended
to supply power to a low voltage electrical
system other than in a starter-motor
application. Do not use battery charger
for charging dry-cell batteries that are
commonly used with home appliances.
These batteries may burst and cause
injury to persons and damage to property.
2.9 NEVER charge a frozen battery.
• 6 •
3. PREPARING TO CHARGE
3.1 If necessary to remove battery from
vehicle to charge, always remove
grounded terminal from battery rst. Make
sure all accessories in the vehicle are off,
so as not to cause an arc.
3.2 Be sure area around battery is well
ventilated while battery is being charged.
3.3 Clean battery terminals. Be careful to
keep corrosion from coming in contact
with eyes.
3.4 Add distilled water in each cell until
battery acid reaches level specied by
battery manufacturer. Do not overll. For a
battery without removable cell caps, such
as valve regulated lead acid batteries,
carefully follow manufacturer’s recharging
instructions.
3.5 Study all battery manufacturer’s
specic precautions while charging and
recommended rates of charge.
3.6 Determine voltage of battery by referring
to car owner’s manual and make sure that
output voltage selector switch is set at
correct voltage. If charger has adjustable
charge rate, charge battery initially at
lowest rate.
4. CHARGER LOCATION
4.1 Locate charger as far away from battery
as DC cables permit.
4.2 Never place charger directly above
battery being charged; gases from battery
will corrode and damage charger.
4.3 Never allow battery acid to drip on
charger when reading electrolyte specic
gravity or lling battery.
4.4 Do not operate charger in a closed-in
area or restrict ventilation in any way.
4.5 Do not set a battery on top of charger.
5. DC CONNECTION PRECAUTIONS
5.1 Connect and disconnect DC output clips
only after setting any charger switches to
“off” position and removing AC cord from
electric outlet. Never allow clips to touch
each other.
5.2 Attach clips to battery and chassis, as
indicated in sections 6 and 7.
6. FOLLOW THESE STEPS WHEN BATTERY IS INSTALLED IN VEHICLE
WARNING: A SPARK NEAR THE
BATTERY MAY CAUSE A BATTERY
EXPLOSION. TO REDUCE THE RISK OF
A SPARK NEAR THE BATTERY:
6.1 Position AC and DC cords to reduce risk
of damage by hood, door, or moving
engine part.
6.2 Stay clear of fan blades, belts, pulleys, and
other parts that can cause injury to persons.
6.3 Check polarity of battery posts. POSITIVE
(POS, P, +) battery post usually has larger
diameter than NEGATIVE (NEG, N,–) post.
6.4 Determine which post of battery is
grounded (connected) to the chassis. If
negative post is grounded to chassis (as
in most vehicles), see (6.5). If positive
post is grounded to the chassis, see (6.6).
6.5 For negative-grounded vehicle, connect
POSITIVE (RED) clip from battery charger
to POSITIVE (POS, P, +) ungrounded post
of battery. Connect NEGATIVE (BLACK)
clip to vehicle chassis or engine block
away from battery. Do not connect clip to
carburetor, fuel lines, or sheet-metal body
parts. Connect to a heavy gauge metal
part of the frame or engine block.
6.6 For positive-grounded vehicle, connect
NEGATIVE (BLACK) clip from battery
charger to NEGATIVE (NEG, N, –)
ungrounded post of battery. Connect
POSITIVE (RED) clip to vehicle chassis
or engine block away from battery. Do
not connect clip to carburetor, fuel lines,
or sheet-metal body parts. Connect to a
heavy gauge metal part of the frame or
engine block.
6.7 When disconnecting charger, turn
switches to off, disconnect AC cord,
remove clip from vehicle chassis, and
then remove clip from battery terminal.
6.8 See Operating Instructions for length of
charge information.
• 7 •
7. FOLLOW THESE STEPS WHEN BATTERY IS OUTSIDE VEHICLE
WARNING: A SPARK NEAR THE
BATTERY MAY CAUSE A BATTERY
EXPLOSION. TO REDUCE THE RISK OF
A SPARK NEAR THE BATTERY:
7.1 Check polarity of battery posts. POSITIVE
(POS, P, +) battery post usually has a larger
diameter than NEGATIVE (NEG, N, –) post.
7.2 Attach at least a 24-inch-long 6-gauge
(AWG) insulated battery cable to
NEGATIVE (NEG, N, –) battery post.
7.3 Connect POSITIVE (RED) charger clip to
POSITIVE (POS, P, +) post of battery.
7.4 Position yourself and free end of cable as
far away from battery as possible – then
connect NEGATIVE (BLACK) charger clip
to free end of cable.
7.5 Do not face battery when making nal
connection.
7.6 When disconnecting charger, always do
so in reverse sequence of connecting
procedure and break rst connection
while as far away from battery as
practical.
7.7 A marine (boat) battery must be removed
and charged on shore. To charge it on
board requires equipment specially
designed for marine use.
8. GROUNDING AND AC POWER CORD CONNECTIONS
8.1 This battery charger is for use on a
nominal 120 volt circuit. The plug must
be plugged into an outlet that is properly
installed and grounded in accordance with
all local codes and ordinances. The plug
pins must t the receptacle (outlet). Do
not use with an ungrounded system.
8.2 DANGER: Never alter the AC cord or
plug provided – if it does not t the outlet,
have a proper grounded outlet installed
by a qualied electrician. An improper
connection can result in a risk of an
electric shock or electrocution.
NOTE: Pursuant to Canadian
Regulations, use of an adapter plug
is not allowed in Canada. Use of an
adapter plug in the United States is not
recommended and should not be used.
8.3 USING AN EXTENSION CORD
The use of an extension cord is not
recommended. If you must use an
extension cord, follow these guidelines:
• Pins on plug of extension cord must be
the same number, size, and shape as
those of plug on charger.
• Ensure that the extension cord is
properly wired and in good electrical
condition.
• Wire size must be large enough for
the AC ampere rating of charger, as
specied:
Length of cord (feet) 25 50 100 150
AWG* size of cord 16 12 10 8
*AWG-American Wire Gauge
9. ASSEMBLY INSTRUCTIONS
9.1 Remove all cord wraps and uncoil the
cables prior to using the battery charger.
9.2 Extend the handle from the retracted
position by pulling it upward until it locks
into place. (Press the small black buttons
inward, if necessary.)
9.3 Clamp cleat installation
1. Slide the short end of the cable clamp
cleat Z-bracket into the open slot.
There are 4 total slots: the top left
and top right, and the bottom left and
bottom right sides of the charger.
2. Insert the No. 8 screw into the open
hole below each slot, to fasten the
cable bracket in place.
NOTE: The screws are #8-18.
Use a 1/4˝ hex screwdriver.
• 8 •
10. CONTROL PANEL
NOTE: Some features are not available
on all models.
12V MEMORY SAVER PORT
(Models DSR122 and DSR124)
DIGITAL DISPLAY
The digital display indicates voltage, % of
charge, or amperage, depending on the
Display Mode chosen.
DISPLAY MODE BUTTON
Use to set the function of the digital
display to one of the following:
V
Volts – The digital display
shows the voltage at the charger’s
battery clamps.
A
Amps – The digital display shows
the charging current, in amps. When
in Boost mode, the display shows the
approximate output current, in amps.
%
Battery percentage – The digital
display shows an estimated charge
percentage of the battery connected to
the charger’s battery clamps.
CHARGING STATUS LEDS
REVERSED CLAMPS LED ashing:
The connections are reversed.
BOOST/CHARGING (yellow/orange)
LED lit: The charger has detected that a
battery is connected, and is performing the
selected operation – either Boost or Charge.
CHARGED/MAINTAINING (green)
LED lit: The battery is fully charged and
the charger is in Maintain mode.
NOTE: See Operating Instructions for a
complete description of the charger modes.
FLASH BUTTON
(Models DSR122 and DSR124)
Press to enter Flash Reprogramming mode.
UP/DOWN ARROW BUTTONS
Use to change any variable settings on
the display.
V
BATTERY VOLTAGE/
MEMORY SAVER BUTTON
Select 6V, 12V or 24V, or select
for the memory saver function.
BATTERY TYPE BUTTON
Use this button to select the battery type.
STD (Standard) – Used in cars, trucks
and motorcycles, these batteries have
vent caps and are often marked “low
maintenance” or “maintenance-free”.
This type of battery is designed to
deliver quick bursts of energy (such as
starting engines) and has a greater plate
count. The plates are thinner and have
somewhat different material composition.
Standard batteries should not be used for
deep-cycle applications.
AGM – The Absorbed Glass Mat
construction allows the electrolyte to
be suspended in close proximity with
the plate’s active material. In theory,
this enhances both the discharge and
recharge efciency. The AGM batteries
are a variant of Sealed VRLA (valve
regulated lead-acid) batteries. Popular
uses include high-performance engine
starting, power sports, deep-cycle, solar
and storage batteries.
GEL – The Gel Cell is similar to the
AGM style because the electrolyte is
suspended, but different because the
AGM battery is still considered to be a
wet cell. The electrolyte in a GEL cell has
a silica additive that causes it to set up
or stiffen. The recharge voltages on this
type of cell are lower than the other styles
of lead-acid battery. This is probably the
most sensitive cell in terms of adverse
reactions to over-voltage charging. Gel
batteries are best used in very deep cycle
applications and may last a bit longer in
hot weather applications. If the incorrect
battery charger is used on a Gel Cell
battery, poor performance and premature
failure is certain.
• 9 •
OUTPUT RATE BUTTON
Select one of the following rates:
Maintain (4A)
For charging small batteries and
maintaining fully charged large batteries.
Fast Charge (15A)
For charging automotive, marine and
light truck batteries.
Boost
Increases the voltage and sends a
quick burst of energy into the battery,
to quickly bring deeply discharged
batteries back to life.
Engine Start
Provides additional amps for cranking
an engine with a weak or run-down
battery. Always use in combination with
a battery.
START/STOP BUTTON
Begins and ends the Charge, Boost,
Engine Start, Flash Reprogram and
Memory Saver modes.
MAIN POWER SWITCH
This switch supplies power to the charger.
REPROGRAMMING
THE DEFAULT SETTINGS
(Models DSR122 and DSR124 only)
If you are satised with the default settings,
skip to Operating Instructions.
When you rst power up the charger, the
default settings are:
Display Mode – Volts
Battery Voltage – 12V
Battery Type – Standard
Output Rate – Maintain (4A)
To change the power up default settings:
1. Change to the desired Display Mode,
Battery Voltage, Battery Type and
Output Rate.
2. Press and hold both Up and Down
Arrow buttons at the same time until
the LEDs stop ashing.
3. The next time you power up the unit,
these settings will be saved and
become the startup default settings.
11. OPERATING INSTRUCTIONS
WARNING: A spark near the battery may
cause an explosion.
IMPORTANT: Do not start the vehicle with
the charger connected to the AC outlet
(except during Engine Start), or it could
damage the charger.
CHARGING A BATTERY IN THE VEHICLE
1. Turn off all the vehicle’s accessories.
2. Keep the hood open.
3. Clean the battery terminals.
4. Place the charger on a dry, non-
ammable surface.
5. Lay the AC/DC cables away from any
fan blades, belts, pulleys and other
moving parts.
6. Connect the battery, following the
precautions listed in sections 6 and 7.
7. Connect the charger to an electrical
outlet.
8. Set Battery Voltage to 6V or 12V.
NOTE: 24V is available only on models
DSR123 and DSR124, for Boost and
Engine Start.
CAUTION:
Always visually conrm the voltage of the
battery being charged. Not doing so can
cause damage to the battery and vehicle’s
electrical system. Other property damage
or personal injury may occur.
9. Set Battery Type to STANDARD,
AGM, or GEL. (If unsure, consult the
label on the battery or the battery
manufacturer.)
10. Set Output Rate to
Maintain (4A),
Fast Charge (15A) or Boost.
11. Charging will start when the START/
STOP button is pressed and nish
automatically.
12. Charged/Maintaining (green) LED
will light when nished and charger will
maintain battery.
13. To stop the battery maintaining process,
press the START/STOP button.
14. When charging is complete, disconnect
the charger from the AC power, remove
the clamps from the vehicle’s chassis,
and then remove the clamp from the
battery terminal.
CHARGING A BATTERY
OUTSIDE OF THE VEHICLE
1. Place battery in a well-ventilated area.
2. Clean the battery terminals.
3. Connect the battery, following the
precautions listed in sections 6 and 7.
4. Connect the charger to the electrical
outlet.
5. Set Battery Voltage to 6V or 12V.
NOTE: 24V is available only on models
DSR123 and DSR124, for Boost and
Engine Start.
CAUTION:
Always visually conrm the voltage of the
battery being charged. Not doing so can
cause damage to the battery and vehicle’s
electrical system. Other property damage
or personal injury may occur.
• 10 •
6. Set Battery Type to STANDARD, AGM,
or GEL. (If unsure, consult the label on
the battery or the battery manufacturer.)
7. Set Output Rate to
Maintain (4A),
Fast Charge (15A) or Boost.
8. Charging will start when the START/
STOP button is pressed and nish
automatically.
9. Charged/Maintaining
(green) LED
will light when nished and charger will
maintain battery.
10. To stop the battery maintaining process,
press the START/STOP button.
11. When charging is complete,
disconnect the charger from the AC
power, disconnect the negative clamp,
and nally the positive clamp.
12. A marine (boat) battery must be
removed and charged on shore.
BATTERY CHARGING TIMES
APPLICATION
BATTERY
SIZE
CHARGING TIME (Hours)
2A 6A 8A 10A
POWERSPORTS
6Ah 6
32 Ah 15
AUTOMOTIVE
300 CCA 12
1000 CCA 30
MARINE
50 Ah 15
105Ah 33
2
5
4
10
5
11
1.75
4.5
3.5
8.5
4.25
9.5
1.5
4
3
7
3.5
8
Times are based on a 50% discharged battery
and may change, depending on age and condition
of battery.
DESULFATION
If the battery is left discharged for an
extended period of time, it could become
sulfated and not accept a normal charge.
If the charger detects a sulfated battery,
the charger will switch to a special mode
of operation designed for such batteries
(6V/12V only). If successful, normal
charging will resume after the battery is
desulfated. Desulfation could take up to
10 hours. If desulfation fails, charging will
abort and the display will show the error
message F02.
ABORTED CHARGE
If charging cannot be completed normally,
charging will abort. When charging aborts,
the charger’s output is shut off, and
the display will show an error code. Do
not continue attempting to charge this
battery. Check the battery and replace, if
necessary.
CHARGE COMPLETION AND MAINTAIN
MODE (FLOAT MODE MONITORING)
Charge completion is indicated by the
green Charged/Maintaining LED.
This means that the charger has stopped
charging and has switched to the Maintain
Mode of operation. NOTE: If the charger
has to provide its maximum maintain
current for a continuous 12 hour period,
it will go into Abort Mode (see Aborted
Charge section). This is usually caused by
a drain on the battery, or the battery could
be bad. Make sure there are no loads on
the battery. If there are, remove them. If
there are none, have the battery checked
or replaced.
MAINTAINING A BATTERY
The charger maintains 6V and 12V
batteries, keeping them at full charge.
NOTE: The maintain mode technology
allows you to safely charge and maintain
a healthy battery for extended periods
of time. However, problems with the
battery, electrical problems in the
vehicle, improper connections or other
unanticipated conditions could cause
excessive current draws. As such,
occasionally monitoring your battery and
the charging process is required.
USING BOOST MODE
1. Set Battery Voltage to 6V, 12V or 24V.
CAUTION:
Always visually conrm the voltage of the
battery being charged. Not doing so can
cause damage to the battery and vehicle’s
electrical system. Other property damage
or personal injury may occur.
NOTE: Additional safety settings have
been added to the charger software.
When the unit is in the 24 volt mode, the
voltage boost output will not activate if
battery voltage is less than 15.5 volts. If
a 24 volt battery has voltage below 15.5
volts, the voltage will be shown on the
digital display and the “Volts” and “24V”
LEDs will ash.The START/STOP button
must be pressed again after conrmation
that the unit is operating on a 24V system.
2. Set Battery Type to STANDARD, AGM,
or GEL. (If unsure, consult the label on
the battery or the battery manufacturer.)
3. Set Output Rate to
Boost.
NOTE: This mode should not be used
for smaller batteries (lawn tractor,
motorcycle, etc.).
4. Boost will start when the START/STOP
button is pressed and will hold batteries
at the following voltages:
6V: held at 6.8V
12V: held at 13.6V
24V: held at 27.3V
5. Boost will end when the START/STOP
button is pressed.
• 11 •
USING ENGINE START MODE
Your battery charger can be used to jump
start your car if the battery is low. Follow
all safety instructions and precautions for
charging your battery. Wear complete eye
protection and protective clothing.
WARNING: Using Engine Start mode
WITHOUT a battery installed in the
vehicle could cause damage to the
vehicle’s electrical system.
NOTE: If you have charged the battery
and it still will not start your car, do
not use Engine Start mode, or it could
damage the vehicle’s electrical system.
Have the battery checked.
1. With the charger unplugged from the
AC outlet, connect the charger to the
battery, following the instructions given
in sections 6 and 7.
2. Set the Battery Voltage to 6V, 12V or 24V.
3. Set the Output Rate to Engine Start.
NOTE: The charger will supply charge to
the battery before cranking.
4. Press the START/STOP button.
The digital display will show On
for 2 minutes.
5. Crank the vehicle when the digital
display shows rdy. Do not crank for
longer than 20 seconds.
NOTE: During extremely cold weather,
or if the battery is under one volt, charge
the battery for 5 minutes before cranking
the engine.
6. Wait three minutes before attempting
to start again. The digital display will
indicate the time remaining before
cranking again.
NOTE: During this cool down period,
the charger is supplying the battery
with a charge of up to 15A.
7. When the digital display times down to
0 and reads rdy, the Boost/Charging
LED is on, you are ready to crank
the vehicle again. You have three
minutes to perform an engine start
(Pressing the START/STOP button is
NOT REQUIRED.)
8. If the engine still does not start, allow
the charger to charge the battery for ve
more minutes before cranking it again.
9. After the engine starts, unplug the AC
power cord before disconnecting the
battery clamps from the vehicle.
NOTE: If the engine does turn over but
never starts, there is not a problem with
the starting system; there is a problem
somewhere else with the vehicle. STOP
cranking the engine until the other problem
has been diagnosed and corrected.
FLASH REPROGRAMMING
(Models DSR122 and DSR124)
NOTE: Do not attempt to Flash Reprogram
a vehicle that has a discharged or
defective battery. Make sure that the
vehicle battery is in good condition and
FULLY CHARGED before proceeding.
The charger is designed to supply up to
100A in “Flash Reprogram” mode.
Some newer vehicles may require more
than 100A while ash reprogramming the
ECU. Consult the vehicle manufacturer’s
specications to determine the required
amperage. The charger’s “Flash
Reprogram” mode cannot be used on
vehicles that require more than 100A,
or damage to the ECU and/or vehicle’s
electrical system may occur. Failure to
follow these instructions may also damage
the service center’s ash reprogram
equipment.
1. Set the mode to Flash.
2. Use (Up) and (Down) buttons
to adjust the voltage needed for the
vehicle being programmed (refer to
OEM specications). Voltage selected
is shown on the digital display. The
unit has a voltage range of 13.0 to
15.0, with a default of 14.2.
NOTE: When the
V
Volts LED stops
blinking, the display shows the selected
voltage.
3. Press START/STOP to activate the
output.
NOTE: During this time, the other buttons
will not work until you turn off the output.
When the display shows OFF, no buttons will
work for ve seconds; then it automatically
goes back to the default state.
4. When nished with Flash Reprogramming,
press START/STOP to exit this mode.
NOTE: The clamps are live during Flash
Reprogramming.
• 12 •
BATTERY PERCENTAGE
Press the Display Mode button to
switch from
V
battery voltage to
A
current or
%
battery percentage.
USING A MEMORY SAVER
(Models DSR122 and DSR124)
Use a memory saver to save the vehicle’s
on-board diagnostic computer settings (radio
programs, diagnostic codes, etc.) while the
battery is disconnected from the vehicle
during repair or maintenance.
NOTE: The 12V port is rated at 15A; the
provided OBDII cable has an 8A fuse.
IMPORTANT!
Some vehicle manufacturers do not allow
the use of a memory saver through the
OBDII. Consult the vehicle manufacturer
before use, to determine if a memory
saver is acceptable for use on the vehicle.
1. Make sure that Charge/Boost/Engine
Start are off. Do not operate or crank
when using a memory saver. Do not
charge a battery when operating the
memory saver
2. Turn off the vehicle and make sure all
accessories are off.
3. Wait at least 30 minutes before using
the memory saver. This ensures that
the accessories are no longer drawing
current from the car battery.
4. Connect the memory saver’s 12V
connector to 12V port on the charger.
5. Press the
V
button until the
Memory Saver LED is lit.
6. Connect the memory saver’s OBD
connector to the vehicle’s OBD plug.
Make sure the connector is fully
engaged.
7. Push the START/STOP button.
8. Disconnect the vehicle’s battery
cables and cover the positive and
negative cables with an insulator,
such as electrical tape. This prevents
the connectors from touching metal,
each other, or the chassis and causing
a short circuit, due to the vehicle’s
electrical system receiving power from
the memory saver through the OBD
connection.
WARNING:
When working with the vehicle’s battery,
review all of the battery manufacturer’s
safety instructions, warnings and
directives regarding battery disconnection,
removal and replacement.
9. Remove the old battery and put the new
battery into position.
10. Remove the insulator from the positive
cable and connect it to the positive
terminal of the new battery.
11. Remove the insulator from the negative
cable and connect it to the negative
terminal of the new battery.
12. Press the START/STOP button to turn
off the memory saver.
13. Once the new battery is connected,
unplug the memory saver’s OBD
connector from the vehicle’s OBD plug.
12. MAINTENANCE AND CARE
A minimal amount of care can keep your
battery charger working properly for years.
• Clean the clamps each time you are
nished charging. Wipe off any battery
uid that may have come in contact with
the clamps to prevent corrosion.
• Occasionally cleaning the case of the
charger with a soft cloth will keep the
nish shiny and help prevent corrosion.
• Coil the input and output cords neatly
when storing the charger. This will help
prevent accidental damage to the cords
and charger.
• Store the charger unplugged from the AC
power outlet in an upright position.
• Store inside, in a cool, dry place. Do not
store the clamps on the handle, clipped
together, on or around metal, or clipped to
the cables.
• 13 •
13. ERROR CODES AND TROUBLESHOOTING
Error Codes
CODE DESCRIPTION REASON/SOLUTION
F 01
The battery voltage is still under 10V
(for a 12V battery) or 5V (for a 6V
battery) after 2 hours of charging.
The battery could be bad. Have it checked or replaced.
SUL
The charger has detected a sulfated
battery.
The charger will go into desulfation mode. If the
desulfation is not successful after 10 hours, the charger
will go into abort mode.
F02
The charger cannot desulfate the
battery.
The battery could not be desulfated; have it checked or
replaced.
F03
The battery was unable to reach the
“full charge” voltage.
May be caused by trying to charge a large battery or
bank of batteries on too low of a current setting. Try
again with a higher current setting or have the battery
checked or replaced.
F04
The connections to the battery are
reversed.
The battery is connected backwards. Unplug the charger
and reverse the connections to the battery.
F05
The charger was unable to keep
the battery fully charged in maintain
mode.
The battery won’t hold a charge. May be caused by a drain
on the battery or the battery could be bad. Make sure there
are no loads on the battery. If there are remove them. If
there are none, have the battery checked or replaced.
F06
The charger detected that the battery
may be getting too hot (thermal
runaway).
The charger automatically shuts the current off if it
detects the battery may be getting too hot. Have the
battery checked or replaced.
If you get an error code, check the connections and settings and/or replace the battery.
Troubleshooting
PROBLEM POSSIBLE CAUSE SOLUTION
No reading or 0.0V
shown on the display.
Clamps are not making a
good connection.
AC cord and/or extension
cord is loose.
No power at receptacle.
Clamp polarity reversed.
Check for poor connection at
battery and frame. Make sure
connecting points are clean.
Check power cord and extension
cord for loose tting plug.
Check for open fuse or circuit
breaker supplying AC outlet.
Verify and reverse the battery
clamps.
The
Boost/Charging
LED does not turn off.
The charger is still in Boost
mode.
The charger is still in one of
the charge modes.
This is normal. In Boost mode, the
LED will not turn off until the
battery is disconnected from the
charger.
This is normal. In one of the charge
modes, the LED will not turn off
until the battery charging process
is completed.
• 14 •
PROBLEM POSSIBLE CAUSE SOLUTION
Short or no start cycle
when cranking engine.
Failure to wait 3 minutes (180
seconds) between cranks.
Clamps are not making a
good connection.
AC cord and/or extension
cord is loose.
No power at receptacle.
The charger may be
overheated.
Battery may be severely
discharged.
Wait three minutes or until the
display reads rdy and the
LED is on.
Check for poor connection at
battery and frame. Make sure
connecting points are clean.
Check power cord and extension
cord for loose tting plug.
Check for open fuse or circuit
breaker supplying AC outlet.
The internal thermal protector may
have tripped and needs
a little longer to close. Wait until it
automatically resets and try again.
On a severely discharged battery,
use the
Boost rate for 10 to 15
minutes, to help assist in cranking.
Charger makes a loud
buzz.
Transformer laminations
vibrate.
No problem; this is a normal
condition.
Battery % stays low
during charging.
Battery is severely
discharged.
Wrong battery voltage
selected.
Continue charging battery for two
more hours. If problem continues,
have the battery checked and
replace, if necessary.
Make sure Battery Voltage switch
is set to the correct voltage for the
battery you are charging.
The “Maintain” and “Fast
Charge” rates do not
work on the 24V setting.
Complete charge of a 24 Volt
battery is not a function of
this unit.
This charger does not fully charge
24V batteries. It boosts the voltage
to 27.3V and holds the voltage at
this level.
Clicking noise from
charger.
Circuit breaker is cycling.
Battery is defective.
Shorted battery clamps.
Severely discharged battery,
but otherwise a good battery.
Reversed connections at
battery.
Under certain conditions, this unit
has a high capacity and the circuit
breaker protects the unit under
these conditions. If the circuit
breaker is cycling often, stop the
operation by pressing the START/
STOP button and wait until the unit
has cooled, to return to operation.
Have the battery checked.
Circuit breaker cycles when current
draw is too high. Check for shorted
cables and replace if necessary.
Allow charging to continue until
battery has a chance to recover
sufciently to take a charge. If more
than 20 minutes, stop charging and
have the battery checked.
Correct the lead connections.
• 15 •
PROBLEM POSSIBLE CAUSE SOLUTION
Display shows “SUL” The battery is sulfated. A sulfated battery may eventually
take a normal charge if left
connected. The charger will continue
to charge with a low current for up to
10 hours to recover the battery. If the
battery will not take a charge after 10
hours, have it checked.
Engine start does not
work.
Vehicle drawing more than
the Engine Start rate.
Failure to wait 3 minutes (180
seconds) between cranks.
The charger may be
overheated.
Battery may be severely
discharged.
Crank time varies with the amount
of current drawn. If cranking draws
more than the Engine Start rate,
crank time may be reduced.
When the Engine Start LED
blinks, wait 3 minutes of rest time
before the next crank.
The thermal protector may have
tripped and needs a little longer to
reset. Make sure the charger vents
are not blocked. Wait and try again.
On a severely discharged battery,
use the
Boost rate for 10 to 15
minutes, to help assist in cranking.
14. BEFORE RETURNING FOR REPAIRS
If these solutions do not eliminate the problem,
or for more information about troubleshooting,
contact customer service for assistance:
www.batterychargers.com
or call 1-800-621-5485
For REPAIR OR RETURN, contact Customer Service at 1-800-621-5485. DO NOT SHIP
UNIT until you receive a RETURN MERCHANDISE AUTHORIZATION (RMA) number
from Customer Service at Schumacher Electric Corporation.
• 16 •
15. SPECIFICATIONS
DSR121
UL
Input .......................................................................................120V AC 60Hz, 12.5A cont., 50A int.
Output ............................................................................................................. 12V DC, 4/15A cont.
50A int. (30 sec. max. ON, 60 sec. min. OFF)
250A int. (20 sec. max. ON, 180 sec. min. OFF)
cUL
Input .......................................................................................120V AC 60Hz, 12.5A cont., 50A int.
Output ............................................................................................................. 12V DC, 4/15A cont.
45A int. (30 sec. max. ON, 60 sec. min. OFF)
250A int. (20 sec. max. ON, 180 sec. min. OFF)
DSR122
Input .......................................................................................120V AC 60Hz, 12.5A cont., 49A int.
Output .......................................................................................................... 6/12V DC, 4/15A cont.
60A int. (60 sec. max. ON, 120 sec. min. OFF
275A int. (20 sec. max. ON, 180 sec. min. OFF)
DSR123
Input .......................................................................................120V AC 60Hz, 12.5A cont., 60A int.
Output ............................................................................................................. 12V DC, 4/15A cont.
12V DC: 50A int. (60 sec. max. ON, 120 sec. min. OFF)
250A int. (20 sec. max. ON, 180 sec. min. OFF)
24V DC: 30A int. (60 sec. max. ON, 120 sec. min. OFF)
150A int. (20 sec. max. ON, 180 sec. min. OFF)
DSR124
Input ................................................................................... 120V AC 60Hz, 12.5A cont., 66.5A int.
Output .......................................................................................................... 6/12V DC, 4/15A cont.
80A int. (120 sec. max. ON, 120 sec. min. OFF)
............................................................................330A int. (20 sec. max. ON, 180 sec. min. OFF)
24V DC: 30A cont.; 250A int. (20 sec. max. ON, 180 sec. min. OFF)
• 17 •
16. LIMITED WARRANTY
WARRANTY NOT VALID IN MEXICO.
SCHUMACHER ELECTRIC CORPORATION, 801 BUSINESS CENTER DRIVE,
MOUNT PROSPECT, IL 60056-2179, MAKES THIS LIMITED WARRANTY TO THE
ORIGINAL RETAIL PURCHASER OF THIS PRODUCT. THIS LIMITED WARRANTY
IS NOT TRANSFERABLE OR ASSIGNABLE.
Schumacher Electric Corporation (the “Manufacturer”) warrants this battery charger
for two (2) years from the date of purchase at retail against defective material or
workmanship that may occur under normal use and care. If your unit is not free from
defective material or workmanship, Manufacturer’s obligation under this warranty is
solely to repair or replace your product with a new or reconditioned unit at the option
of the Manufacturer. It is the obligation of the purchaser to forward the unit, along with
proof of purchase and mailing charges prepaid to the Manufacturer or its authorized
representatives in order for repair or replacement to occur.
Manufacturer does not provide any warranty for any accessories used with this product
that are not manufactured by Schumacher Electric Corporation and approved for use
with this product. This Limited Warranty is void if the product is misused, subjected
to careless handling, repaired, or modied by anyone other than Manufacturer or if
this unit is resold through an unauthorized retailer. Manufacturer may void this Limited
Warranty if a “warranty void if removed” label is removed from the product.
Manufacturer makes no other warranties, including, but not limited to, express, implied or
statutory warranties, including without limitation, any implied warranty of merchantability
or implied warranty of tness for a particular purpose. Further, Manufacturer shall
not be liable for any incidental, special or consequential damage claims incurred by
purchasers, users or others associated with this product, including, but not limited to,
lost prots, revenues, anticipated sales, business opportunities, goodwill, business
interruption and any other injury or damage. Any and all such warranties, other than the
limited warranty included herein, are hereby expressly disclaimed and excluded. Some
states do not allow the exclusion or limitation of incidental or consequential damages or
length of implied warranty, so the above limitations or exclusions may not apply to you.
This warranty gives you specic legal rights and it is possible you may have other rights
which vary from this warranty.
THIS LIMITED WARRANTY IS THE ONLY EXPRESS LIMITED WARRANTY AND THE
MANUFACTURER NEITHER ASSUMES OR AUTHORIZES ANYONE TO ASSUME
OR MAKE ANY OTHER OBLIGATION TOWARDS THE PRODUCT OTHER THAN
THIS WARRANTY.
Schumacher
®
and the Schumacher logo are registered trademarks
of Schumacher Electric Corporation.
• 18 •
1. INSTRUCCIONES IMPORTANTES DE SEGURIDAD
GUARDE ESTAS INSTRUCCIONES.
1.1 GUARDE ESTAS INSTRUCCIONES –
Este manual contiene instrucciones
operativas y de seguridad de importancia.
1.2 Manténgase alejado de los niños.
1.3 No exponga el cargador a la lluvia
o a la nieve.
1.4 El uso de un accesorio no recomendado
o suministrado por por el fabricante del
cargador de baterías puede provocar
riesgo de incendio, descarga eléctrica o
lesiones a personas.
1.5 Para reducir el riesgo de daños al
enchufe o cable eléctrico, jale del enchufe
en lugar de jalar del cable al desconectar
el cargador.
1.6 No se debe utilizar un alargador a menos
que resulte absolutamente necesario. El
uso de un alargador inadecuado puede
provocar riesgo de incendio o descarga
eléctrica. En caso de que deba utilizarse
un alargador, asegúrese de que:
• Los pasadores en el enchufe del
alargador posean el mismo número,
tamaño y forma que aquellos presentes
en el enchufe del cargador.
• El alargador se encuentre correctamente
conectado y en buenas condiciones
eléctricas; y
• El tamaño del cable sea lo
sucientemente extenso para el
amperaje en CA del cargador como se
especica en la sección 8.
1.7 No utilice el cargador si el mismo posee
un enchufe o cable dañado; substituya el
cable o el enchufe inmediatamente por
una persona calicada en el ramo.
1.8 No utilice el cargador si el mismo recibió
un golpe fuerte, si se cayó o si sufrió
daños de cualquier otra forma; hágalo
revisar por una persona capacitada que
efectúe reparaciones.
1.9 No desarme el cargador; hágalo revisar
por una persona capacitada que efectúe
reparaciones cuando necesite servicio
de mantenimiento o una reparación.
Volver a ensamblar el cargador en forma
incorrecta puede provocar riesgo de
incendio o descarga eléctrica.
1.10 Para reducir el riesgo de descarga
eléctrica, desenchufe el cargador del
tomacorriente antes de intentar llevar a
cabo cualquier actividad de mantenimiento
o limpieza. El simple apagado de los
controles no reducirá este riesgo.
1.11 ADVERTENCIA:
RIESGO DE GASES EXPLOSIVOS.
a. RESULTA PELIGROSO TRABAJAR EN
FORMA CERCANA A UNA BATERÍA DE
PLOMO. LAS BATERÍAS GENERAN
GASES EXPLOSIVOS DURANTE
SU NORMAL FUNCIONAMIENTO.
POR ESTE MOTIVO, RESULTA DE
SUMA IMPORTANCIA QUE SIGA LAS
INSTRUCCIONES CADA VEZ QUE
UTILIZA EL CARGADOR.
b. Para reducir el riesgo de explosión de
una batería, siga estas instrucciones y
aquellas publicadas por el fabricante
de la batería y por el fabricante de
cualquier equipo que intente utilizar
en la proximidad de la batería. Revise
las pautas de precaución en estos
productos y en el motor.
2. PRECAUCIONES DE SEGURIDAD PERSONAL
2.1 Considere la idea de que alguna persona
se encuentre cerca suyo para poder
ayudarlo cuando trabaje en forma
cercana a una batería de plomo-ácido.
2.2 Cuente con una gran cantidad de agua
potable y jabón a mano en caso de que el
ácido de la batería tenga contacto con su
piel, ropa u ojos.
2.3 Utilice protección visual y corporal
completa, incluyendo gafas de seguridad
y prendas de protección. Evite tocar sus
ojos mientras trabaje en forma cercana a
la batería.
2.4 Si el ácido de la batería tiene contacto con
su piel o su ropa, lave de inmediato el área
afectada con agua y jabón. En caso de que
ingrese ácido en un ojo, sumerja el mismo
de inmediato bajo agua potable corriente
por al menos 10 minutos y obtenga
atención médica en forma inmediata.
2.5 NUNCA fume o permita la presencia de
chispas o llamas en la proximidad de una
batería o motor.
2.6 Tenga especial cuidado para reducir el
riesgo de dejar caer una herramienta
de metal sobre la batería. Esto podría
provocar chispas o un cortocircuito en la
batería o en cualquier otra pieza eléctrica
que podría provocar una explosión.
2.7 No utilice elementos personales de
metal tales como anillos, pulseras,
collares y relojes al trabajar con una
batería de plomo-ácido. Una batería
de plomo-ácido puede producir
• 19 •
una corriente de cortocircuito lo
sucientemente elevada como para
soldar un anillo o provocar efectos
similares sobre el metal, causando una
quemadura de gravedad.
2.8 Utilice este cargador solamente para
cargar baterías recargables de PLOMO-
ÁCIDO (estándar, AGM o GEL) con
recomienda usar capacidad de la batería
de 24Ah (6V) y 44-75Ah (12V). Este
cargador no está destinado a suministrar
energía a sistemas eléctricos de baja
tensión más que en una aplicación de
un motor de arranque. No utilice este
cargador de batería para cargar baterías
de pila seca que por lo general se utilizan
con artefactos domésticos. Estas baterías
podrían explotar y provocar lesiones a
personas o daño a la propiedad.
2.9 NUNCA cargue una batería congelada.
3. PREPARACIÓN PARA LA CARGA
3.1 Si resulta necesario extraer la batería
del vehículo para cargarla, siempre retire
el terminal con descarga a tierra en
primer lugar. Asegúrese de que todos los
accesorios en el vehículo se encuentren
apagados para evitar la formación de
arcos eléctricos.
3.2 Asegúrese de que el área que rodea a
la batería se encuentre bien ventilada
mientras se carga la batería.
3.3 Limpie los terminales de la batería antes
de cargar la batería. Durante la limpieza,
evite que la corrosión producida por aire
tenga contacto con sus ojos.
3.4 Agregue agua destilada a cada pila hasta
que el ácido de la batería alcance el
nivel especicado por el fabricante de la
batería. No provoque derrames. En lo que
concierne a baterías que no cuentan con
tapas extraíbles para pilas, tales como
baterías de plomo-ácido reguladas por
válvulas (VRLA, por sus siglas en inglés),
siga cuidadosamente las instrucciones de
recarga del fabricante.
3.5 Lea, comprenda y siga todas las
instrucciones para el cargador, la batería,
el vehículo y cualquier equipo que se
utilice cerca de la batería y el cargador.
Controle todas las precauciones
especícas establecidas por el fabricante
de la batería al realizar la carga, así
también como los índices de carga
recomendados.
3.6 Determine la tensión de la batería al
consultar el manual del usuario del
vehículo y asegúrese de que el interruptor
de selección de la tensión de salida
se encuentre establecido en la tensión
correcta (en su caso). Si el cargador
posee un índice de carga ajustable,
cargue la batería en el menor índice en
primer lugar.
4. UBICACIÓN DEL CARGADOR
4.1 Ubique el cargador a la mayor distancia
posible de la batería como lo permitan los
cables de CC.
4.2 Nunca ubique el cargador directamente
por encima de la batería que se carga; los
gases de la batería corroerán y dañarán
el cargador.
4.3 Nunca permita que el ácido de la batería
gotee sobre el cargador al leer el peso
especíco del electrolito o al cargar la
batería.
4.4 No utilice el cargador en un área cerrada o
restrinja la ventilación en cualquier forma.
4.5 No ubique la batería encima del cargador.
5. PRECAUCIONES DE CONEXIÓN EN CC
5.1 Conecte y desconecte las pinzas de
salida CC. sólo después de haber
establecido todos los interruptores del
cargador a la posición de “apagado” (si
es aplicable) y de haber desconectado
el enchufe de C.A. del tomacorriente
eléctrico. Nunca permita que las pinzas
tengan contacto entre sí.
5.2 Sujete las pinzas a la batería y al chasis,
como se indica en en las secciones 6 y 7.
• 20 •
6. SIGA ESTOS PASOS CUANDO LA BATERÍA ESTÉ COLOCADA EN EL VEHÍCULO
ADVERTENCIA:
UNA CHISPA PROVOCADA CERCA
DE LA BATERÍA PUEDE CAUSAR LA
EXPLOSIÓN DE LA BATERÍA. PARA
REDUCIR EL RIESGO DE PROVOCAR
CHISPAS CERCA DE LA BATERÍA:
6.1 Ubique los cables de CA y CC
adecuadamente para reducir el riesgo
de daños por la cubierta, la puerta y las
piezas móviles o calientes del motor.
6.2 Manténgase alejado de las paletas del
ventilador, correas, poleas y otras piezas
que podrían provocar lesiones.
6.3 Verique la polaridad de los bornes de
la batería. El borne POSITIVO (POS,
P, +) de la batería generalmente posee
un diámetro mayor al borne NEGATIVO
(NEG, N, -).
6.4 Determine qué borne de la batería
hace descarga a tierra (se encuentra
conectado) con el chasis. Si el borne
negativo hace descarga a tierra con el
chasis (como en la mayor parte de los
vehículos), ver el paso (6.5). Si el borne
positivo hace descarga a tierra con el
chasis, ver el paso (6.6).
6.5 En un vehículo con descarga a tierra
por borne negativo, conecte el gancho
POSITIVO (ROJO) del cargador de
batería al borne POSITIVO (POS, P, +) sin
descarga a tierra de la batería. Conecte
el gancho NEGATIVO (NEGRO) al chasis
del vehículo o al bloque motor alejado
de la batería. No conecte el gancho al
carburador, líneas de combustible o
cuerpos metálicos. Conecte a una pieza
metálica de calibre grueso del marco o
del bloque motor.
6.6 En un vehículo con descarga a tierra
por borne positivo, conecte el gancho
NEGATIVO (NEGRO) del cargador de
batería al borne NEGATIVO (NEG, N, -)
sin descarga a tierra de la batería.
Conecte el gancho POSITIVO (ROJO)
al chasis del vehículo o al bloque motor
alejado de la batería. No conecte al
carburador, líneas de combustible o
cuerpos metálicos. Conecte a una pieza
metálica de calibre grueso del marco o
del bloque motor.
6.7 Al desconectar el cargador, apague todos
los interruptores (en su caso), desconecte
el cable de C.A., retire el gancho del
chasis del vehículo y luego retire el gancho
del terminal perteneciente a la batería.
6.8 Vea Instrucciones de Operación para
duración de la carga.
7. SIGA ESTOS PASOS CUANDO LA BATERÍA SE ENCUENTRE FUERA DEL VEHÍCULO
ADVERTENCIA:
UNA CHISPA PROVOCADA CERCA
DE LA BATERÍA PUEDE CAUSAR LA
EXPLOSIÓN DE LA BATERÍA. PARA
REDUCIR EL RIESGO DE PROVOCAR
CHISPAS CERCA DE LA BATERÍA:
7.1 Verique la polaridad de los bornes de
la batería. El borne POSITIVO (POS,
P, +) de la batería generalmente posee
un diámetro mayor al borne NEGATIVO
(NEG, N, -).
7.2 Sujete al menos un cable aislado de
batería de 24 pulgadas (61 cm) de largo
con calibre 6 según el Calibre americano
de cables (AWG, por sus siglas en inglés)
al borne NEGATIVO (NEG, N, -) de la
batería.
7.3 Conecte el gancho POSITIVO (ROJO) del
cargador al borne POSITIVO (POS, P, +)
de la batería.
7.4 Ubíquese junto con el extremo libre del
cable que previamente sujetó al borne
NEGATIVO (NEG, N, -) de la batería a
la mayor distancia posible de la batería.
Luego conecte el gancho NEGATIVO
(NEGRO) del cargador al extremo libre
del cable.
7.5 No se ubique en posición frontal a la
batería al realizar la conexión nal.
7.6 Al desconectar el cargador, siempre
hágalo en forma inversa al procedimiento
de conexión y realice la primera conexión
tan lejos de la batería como sea posible.
7.7 Una batería marina (para barcos) se
debe retirar y cargar en tierra. Para
realizar una carga a bordo se necesitan
equipamientos especialmente diseñados
para uso marino.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
Schumacher DSR121 12V 250A ProSeries Battery Charger/Engine Starter DSR122 6/12V 275A ProSeries Battery Charger/Engine Starter DSR123 12/24V 250A ProSeries Battery Charger/Engine Starter DSR124 6/12/24V 330A ProSeries Battery Charger/Engine Starter Le manuel du propriétaire
- Catégorie
- Chargeurs de batterie
- Taper
- Le manuel du propriétaire
dans d''autres langues
- English: Schumacher DSR121 12V 250A ProSeries Battery Charger/Engine Starter DSR122 6/12V 275A ProSeries Battery Charger/Engine Starter DSR123 12/24V 250A ProSeries Battery Charger/Engine Starter DSR124 6/12/24V 330A ProSeries Battery Charger/Engine Starter Owner's manual
- español: Schumacher DSR121 12V 250A ProSeries Battery Charger/Engine Starter DSR122 6/12V 275A ProSeries Battery Charger/Engine Starter DSR123 12/24V 250A ProSeries Battery Charger/Engine Starter DSR124 6/12/24V 330A ProSeries Battery Charger/Engine Starter El manual del propietario
Documents connexes
-
Schumacher Electric DSR121 Le manuel du propriétaire
-
Schumacher MC1220 Professional Wheel Charger Le manuel du propriétaire
-
-
-
-
-
-
-
-