Aiwa CSD-EL50 Operating Instructions Manual

Aiwa
Marque
Aiwa
Modèle
CSD-EL50
Catégorie
Lecteurs de cassettes
Taper
Operating Instructions Manual
WARNING
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE T() RAIN OR MOISTURE.
k5
“CAUTION: TO REDUCETHE RISK OF
NO USER-SERVICEABLE PARTS INSIDE,
REFER SERVICING TO QUALIFIED
Explanation of Graphical Symbols:
AA
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended toalertthe user
to the presence of uninsulated “dangerous volt-
age” within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric
shclck to persons.
A
The exclamation point within an equilateral trian-
gle is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
●
appliance.
OWNER’S RECORD
For your convenience, record the model number (you will find it at the
bottom of the unit) and serial number (you will find it in the battery
compartment) in the space provided below. Please refer to them when
you contact your AIWA dealer in case of difficulty,
Model No.
c= ‘erialNO ~
NOTE
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruc-
tions, may cause harmful interference to radio communications. How-
ever, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equip-
ment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
,,.
Reorient or relocate the receiving antenna.
.,.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CAUTION
Modifications or adjustments to this product, which are not expressly
approved by the manufacturer, may void the user’s right or authority to
operate this product.
2 ENGLISH
PRECAUTIONS
Read the Operating Instructions carefully and completely
before operating the unit. Be sure to keep the Operating
Instructions for future reference. All warnings and cautions in
the Operating Instructions and on the unit should be strictly
followed, as well as the safety suggestions below.
Installation
1
2
3
4
5
6
7
8
Water and moisture - Do not use this unit near water,
such as near a bathtub, washbowl, kitchen sink, laundry
tub, in a wet basement, swimming pool, or the like.
Heat - Do not use this
unit near sources of heat, including
heating vents, stoves, or other appliances that generate
heat.
It also should not be placed in temperatures less than 5°C
(41‘F) or greater than 35°C (95°F).
Mounting surface - Place the unit on a flat, even surface.
Ventilation - The unit should be situated with adequate
space around it so that proper heat ventilation is assured.
Allow 10 cm (4 in.) clearance from the rear and the top of
the unit and 5 cm (2 in.) from each side.
- Do not place the unit on a bed, rug, or similar surface
that may block the ventilation openings.
- Do not install the unit in a bookcase, cabinet, or airtight
rack where ventilation may be impeded.
Objects and liquid entry - Take care that objects or
liquids do not get inside the unit through the ventilation
openings.
Carts and stands - When placed or
mounted on a stand or cart, the unit should
be moved with care.
@
●
Quick stops, excessive force, and uneven ~
3
surfaces may cause the unit or cart to
A
●**
overturn or fall.
Condensation - Moisture may form on the CD pickup
lens when:
- The unit is moved from a cold spot to a warm spot
- The heating system has just been turned on
- The unit is used in a very humid room
- The unit is cooled by an air conditioner
When this unit has condensation inside, it may not
function normally. Should this occur, leave the unit for a
few hours, then try to operate again.
Wall or ceiling mounting - The unit should not be
mounted on a wall or ceiling, unless specified in the
Operating Instructions.
Electric Power
1
2
3
Power sources - Use on batteries or AC house current,
as specified in the Operating instructions and marked on
the unit.
Polarization - As a safety feature, some units are
equipped with polarized AC power plugs which can only
be inserted one way into a power outlet. If it is difficult or
impossible to insert the AC power plug into an outlet, turn
the plug over and try again. If it still does not easily insert
into the outlet, please call a qualified service technician to
service or replace the outlet. To avoid defeating the
safety feature of the polarized plug, do not force it into a
power outlet.
AC power cord
- When disconnecting the AC power cord, pull it out by
the AC power plug. Do
not pull the cord itself.
- Never handle the AC power plug with wet hands, as this
could result in fire or shock.
- Power cords should be firmly secured to avoid being
bent, pinched, or walked upon. Pay particular attention
to the cord from the unit to the power socket.
- Avoid overloading AC power plugs and extension cords
beyond their capacity, as this could result in fire or
shock.
4
5
Extension cord - To help prevent electric shock, do not
use a polarized AC power plug with an extension cord,
receptacle, or other outlet unless the polarized plug can
be completely inserted to prevent exposure of the blades
of the plug.
When not in use - Unplug the AC power cord from the
AC outlet or remove all the batteries if the unit will not be
used for several months or more. When the cord is
plugged in, a small amount of current continues to flow to
the unit, even when the power is turned off.
Maintenance
Clean the unit only as recommended in the Operating
Instructions.
Damage Requiring Service
Have the units serviced by a qualified service technician if:
- The AC power cord or plug has been damaged
- Foreign objects or liquid have got inside the unit
- The unit has been exposed to rain or water
- The unit does not seem to operate normally
- The unit exhibits a marked change in performance
- The unit has been dropped, or the cabinet has been
damaged
D~
TABLE OF CONTENTS
PREPARATIONS
.
POWER SUPPLY ................................................................. 4
REMOTE CONTROL ...........................................................
4
BEFORE OPERATION ........................................................ 5
SOUND
ADJUSTING THE SOUND ..................................................5
RADIO RECEPTION
MANUAL TUNING ............................................................... 6
PRESETTING STATIONS .................................................... 7
CD PLAYING
.
CD Operations ........m....................................................... 8
TAPE PLAYBACK
TAPE OPERATIONS .......................................................... 10
FIECORDING
BASIC RECORDING .........................................................
11
DUBBING A TAPE MANUALLY
........................................
12
DUBBING THE WHOLE TAPE .......................................... 12
Al EDIT RECORDING ....................................................... 13
PROGRAMMED EDIT RECORDING ................................ 14
CLOCK AND TIMER
SETTING THE CLOCK ...................................................... 16
SETTING THE TIMER ....................................................... 16
SETTING THE SLEEP TIMER ........................................... 17
GENERAL
CARE AND Maintenance ............................................. 18
SPECIFICATIONS ............................................................. 18
TROUBLESHOOTING GUIDE .......................................... 19
PARTS INDEX ................................................................... 19
ENGLISH 3
POWER SUPPLY
REMOTE CONTROL
USING ON AC HOUSE CURRENT
Connect the AC cord as illustrated below.
inlet of the unit
0 to an
AC outlet
CAUTION
Use only the supplied AC cord. Use with other cords may
result in the risk of fire.
USING ON BATTERIES
Open the lid of the battery compartment on the rear and
insert eight R14 (size C) batteries, not supplied, as illustrated
below. Then close the lid.
To switch from AC power supply to battery power
supply, disconnect the AC cord from the AC inlet.
The batteries need to be replaced when:
The OPE/BATT indicator becomes dim, the tape speed
slows down, volume decreases, or sound is distorted during
operation.
Notes on batteries
To avoid damage from leakage or explosion, observe the
following:
● Insert the batteries with the 0 and O marks correctly
aligned.
● Do not mix different types of batteries or old batteries with
new ones.
● Never recharge the batteries, apply heat to them or take
them apart.
● Remove dead batteries.
If liquid leaks from the batteries, wipe thoroughly to remove.
Inserting batteries
Detach the battery cover on the rear of the remote control
and insert two R6 (size AA) batteries.
When to replace the batteries
The maximum operational distance between the remote
control and the sensor on the main unit (REMOTE SENSOR)
should be approximately 5 meters (16 feet), When this
distance decreases, replace the batteries with new ones.
REMOTE SENSOR
Using the remote control
The instructions in this manual refer mainly to the buttons on
the main unit. Buttons on the remote control with the same
names as those on the main unit can be used as well.
NOTE
● If the unit is not going to be used for an extended period of
time, remove the batteries to prevent possible electrolyte
leakage.
● The remote control may not operate correctly when:
- The line of sight between the remote control and the unit
is exposed to intense light, such as direct sunlight
- Other remote controls are used nearby (television, etc.)
SHIFT—
FUNCTION—
3
Q9a’
C20a
000
902
moo,
000
000
moo
To use the SHIFT button
—--’a
Buttons @ have two different functions. One of the functions
is indicated on the button, and the other on the plate above
the button.
To use the function on the button, simply press the button.
To use the function on the plate above the button, press the
button while pressing the SHIFT button.
To use the FUNCTION button
The FUNCTION button substitutes for the function buttons
(TAPE, TUNER, CD) on the main unit. Each time the
FUNCTION button is pressed while the power is on, the next
function is selected cyclically.
4 ENGLISH
BEFORE OPERATION
ADJUSTING THE SOUND
POWER
Function
To turn the unit on
Press one of the function buttons (TAPE, TUNER, CD).
Playback of the inserted disc or tape begins, or the
previously tuned station is received (Direct Play Function).
The POWER button is also available.
The disc compartment may open and close to reset the unit.
After use
Press the POWER button to turn off the power. The display
changes to the clock.
NOTE
When using on the batteries, you cannot turn the power on
with the remote control.
Using the headphones
Connect headphones to the (_lPHONES jack on the rear of
the LInit with a stereo mini plug (03.5 mm,
‘/8 inch).
No sound is output from the speakers while the headphones
are plugged in.
VOLUME CONTROL
Turn the VOLUME/TIMER control on the main unit or press
the VOLUME buttons on the remote control.
SUPER T-BASS SYSTEM
l-he T-BASS system enhances the realism of low-frequency
sound,
Press the T-BASS button.
“ro cancel, press the button again.
INOTE
Low frequency sound may be distorted when the T-BASS
system is used for a disc or tape in which low frequency
sound is originally emphasized. In this case, cancel the T-
BASS system.
QSOUND SYSTEM
The QSOUND system provides a rich, three dimensional
sound area.
You can enjoy more enhanced sound.
Press the QSOUND button.
To cancel, press the button again
NOTE
At higher volumes, turning QSOUND on may cause sound
distortion. In this case, turn the volume down.
EQUALIZER MODE
Press the 3-MODE EQUALIZER button until the desired
equalizer mode is displayed.
The equalizer mode changes to ROCK, POP, JAZZ or no
equalization, cyclically.
When using the remote control, press the EQ button.
ROCK Powerful sound emphasizing treble and bass
POP: More presence in the vocals and midrange
JAZZ Accented lower frequencies for jazz-type music
ENGLISH 5
MANUAL TUNING
1
2
2
1
r
000
000
000
00
~;:NDI/
1 1
00
C)oo
TUNER
Cloo
L$oo
SHIFT
o
Press the TUNER/BAND button repeatedly to
select the desired band.
m
If the power is turned off, the previously tuned station will
be played (Direct Play Function).
When using the remote control, press the BAND/MODE
TUNER button repeatedly while the power is on.
Press the + or - TUNING button to select a
station.
Each time the button is pressed, the frequency changes.
During FM stereo reception, “STEREO” is displayed.
To search for a station quickly (Auto Search)
Keep the + or - TUNING button pressed until the tuner starts
searching for a station. After tuning in to a station, the
search stops.
To stop the Auto Search manually, press the + or - TUNING
button.
. The Auto Search may not stop at stations with very weak
signals.
For better reception
FM
Extend the FM antenna and orient it for the best reception.
AM
The AM antenna is inside the unit. Position the unit for the
best reception.
When an FM stereo broadcast contains noise
Press the BAND/MODE TUNER button while pressing the
SHIFT button on the remote control.
“MONO” appears on the display.
Noise is reduced, although reception is monaural.
MONO
To restore stereo reception, repeat the above again.
To change the
AM tuning interval
The default setting of the AM tuning interval is 10 kHz/step.
If you use this unit in an area where the frequency allocation
system is 9 kHz/step, change the tuning interval.
Press the POWER button while pressing the TUNER/BAND
button.
To reset the interval, repeat this procedure.
NOTE
When the AM tuning interval is changed, all preset stations
(see “PRESETTING STATiONS”) are cleared. The preset
stations have to be set again.
A
6 ENGLISH
PRESETTING STATIONS
2——————7
+> PRESET
❑ CLEAR
1
1
You can preset up to 15 stations in each band. When a
station is stored, a preset number is assigned to the station.
Use the preset number to tune in to a preset station directly.
1
2
3
Press the TUNER/BAND button to select a
band. Then,
press the + or - TUNING button to
select a station.
Press the 1I SET button to store the station.
A station is assigned a preset number, beginning from 1
in consecutive order for each band.
Frequency
Preset number
“MEMO” on the display indicates that the unit holds a
preset station.
Repeat
steps 1 and 2.
PRESET NUMBER TUNING
Use
the remote control to select the preset number directiy.
K
000
Oola
o–9, +10
00=
Oc
I.li_Ooc
0’00
BAND
=09
000
0
Press the BAND button to select a band.
Press the numbered buttons to select a preset
number.
Example:
To select preset number 15, press the +1Oand 5
buttons.
To select preset number 10, press the +1O and O
buttons.
Selecting a preset number on the main unit
Press the TUNER/BAND button to select a band. Then,
press the +- PRESET button repeatedly.
Each time the button is pressed, the next highest number is
selected.
To clear a preset station
Select the preset station to be cleared. Then, press the 9
CLEAR button, and press the II SET button within 4
seconds.
The preset numbers of all other stations in the band with
higher numbers are also decreased by one.
ENGLISH ~
CD OPERATIONS
— RANDOM
k-
(=% “-
L
“1
REPEAT
L+
-0
0-9,+10
~~EDIT/
Oc 3
CHECK
I___J
00
1.
Ill
L~QO
000
SHIFT
000
0
LOADING A DISC
Press the CD button, then press the & CD OPEN
button to open the disc compartment. Load a disc
with the label side up and close the disc
compartment.
t-
1
“Total playing time
Total num~er of tracks
PLAYING A DISC
Load a disc.
Press the ~ ➤ button.
Play begins with the first track.
Elapsed playing time
Track number being played
To stop play, press the ■ button.
To pause play, press the II button. To resume play, press
again.
To search for a particular point during playback, keep the
+ or X button pressed and release the button at the
desired point.
To skip to the beginning of a track during playback,
press the < or > button repeatedly.
To remove discs, press the A CD OPEN button.
To start play when the power is off (Direct Play Function;
Press the CD button. The power is turned on and play of the
loaded disc begins.
To replace the disc before play, press the 4 CD OPEN
button to open the disc compartment.
To check the remaining time
Press the EDIT/CHECK button while pressing the SHIFT
button on the remote control during play. The amount of time
remaining until all tracks finish playing is displayed. To
restore the play time display, repeat the above.
Selecting a track with the remote control
Press the numberd buttons and the +1Obutton to select a
track.
Example:
To select the 25th track, press the +1O, +1Oand 5 buttons.
To select the 10th track, press the +1Oand Obuttons.
The selected track starts to play and play continues to the
end of that disc.
NOTE
● Do not use irregular shaped CDs (example: heart-shaped,
octagonal ones).
It may result in malfunctions.
● When loading an 8-cm (3-inch) disc, put it onto the inner
circle of the tray.
● Do not place more than one compact disc on the disc tray.
8 ENGLISH
RANDOM PLAY
PROGRAMMED PLAY
All the tracks on the disc can be played randomly.
Up to 30 tracks can be programmed from the inserted disc,
Press the RANDOM button while pressing the SHIFT
button on the remote control.
“RANDOM” lights upon the display.
.L
_Ql 1
To cancel random play, repeat the above.
E
00
2
00=
NOTE
OG 3
II
● Even if the - button is pressed, a previously played track
cannot be skipped. The unit returns to the beginning of the
. :;: 13*:’-
current track only.
H
c
* During random play, one-track repeat (C 1) cannot be
performed.
* If you select tracks with the numbered buttons, random play
Use the remote control.
is canceled.
~
Press the PRGM button while pressing the
REPEAT PLAY
SHIFT button in stop mode.
Onl~ the current track is repeated. (C 1 is displayed.) 2 Press the numbered buttons and the +1 O button
J.
All the tracks are repeated. (C is displayed.)
to program a track.
Example:
L
The repeat play is canceled. (C disappears.)
To se(ect the 12th track, press the +1Oand 2 buttons.
To select the 20th track, press the +1O, +1Oand O
buttons.
Total playing time of
Program number
the selected tracks
Selected track number
Total number of
‘3
4
selected tracks
Repeat step 2 to program other tracks.
Press the > button to start play.
The > button substitutes for the ~~ button on the
main unit.
To check the program
Each time the - or - button is pressed in stop mode, a
track number and program number will be displayed.
To clear the program
Press the H CLEAR button in stop mode.
To add tracks to the program
Before playing, repeat step 2. The new track will be
programmed after the last track.
To change the programmed tracks
Clear the program and repeat all the steps.
NOTE
During programmed play, the EDIT/CHECK, RANDOM and
numbered buttons do not function.
ENGLISH9
TAPE OPERATIONS
OPEN
(Deck 2)
INSERTING A TAPE
● Use Type I (normal) tapes only.
● On deck 1, you can select a reverse mode to play back one
or both sides,
● On deck 2, only the side facing up is played.
Press the TAPE button and press the OPEN mark
to open the cassette holder.
PEN
Insert a tape with the exposed side down. Push the cassette
holder to close.
To select playing deck
When tapes are loaded in both decks, press the TAPE/
DECK 1/2 button to select a deck. The selected deck number
is displayed.
To select a reverse mode (deck 1 only)
Each time the REV MODE button is pressed, the reverse
mode changes.
PLAYING BACK A TAPE
Insert a tape.
Press the 4> button to start play.
Playing deck
number
Playback side of the tape
The tape counter indicates
the tape running length
4: The front side is being played (forward).
P (deck 1 only): The back side is being played (reverse).
To stop play, press the Z button,
To pause play (deck 2 only), press the II button. To
resume play, press again.
To change the playback side (deck 1 only), press the +>
button in play mode.
To fast forward or rewind, press the < or - button in
stop mode. Then press the 9 button to stop the tape.
To start play when the power is off (Direct Play Function)
Press the TAPE/DECK 1/2 button. The power is turned on
and play of the inserted tape begins.
To set the tape counter to 0000
Press the
■ button in stop mode.
The counter is also set to 0000 when the cassette holder is
opened.
CONTINUOUS PLAY
After play on deck 1 finishes, play on deck 2 will start without
interruption.
1 Press the TAPE/DECK 1/2 button to select deck 1.
2 Press the REV MODE button to select C= .
3 Start play with the <b button.
To play one side only, select =.
To play from front side to back side once only, select (1
To play both sides repeatedly, select C=).
10 ENGLISH
BASIC RECORDING
This section explains how to record from the tuner or CD
player.
o
000
000
000
000
000
000
=
o
b
0 TAPE RECf
REC MUTE
Preparation
● Set the tape to the point where recording will start.
● IJse Type I (normal) tapes only.
● Note that recording will be done on one side of the tape
only.
1
2
3
TO
Insert the tape to be recorded on into deck 2.
Insert the tape with the side to be recorded on facing up
and the exposed side down.
OP
Press one of the function buttons and prepare
the source to be recorded.
To record from a CD, press the CD button and load the
disc.
To record from a radio broadcast, press the TUNER/
BAND button and tune in to a station.
Press the ● REC/REC MUTE button to start
recording.
“REC” on the display flashes.
When the selected function is CD, playback and
recording start simultaneously.
sto~ recordinca, mess the
■ button.
To pause record~g, press the 11 button. (Applicable when
the source is TUNER.) To resume recording, press again.
To start recording with the remote control
First press the @ TAPE REC/REC MUTE button, and then
press the k button within 2 seconds.
NOTE
If squealing or beating sounds occur when recording an AM
broadcast, press the BAND/MODE TUNER button while
pressing the SHIFT button on the remote control, so as to
eliminate the noise.
Each time the buttons are pressed, the dot light on the
display is turned on and off.
The dot light
INSERTING BLANK SPACES
W’hen recording from a radio broadcast, 4-second blank
spaces can be inserted at the desired point.
1
:2
Press the
● REC/REC MUTE button during recording
or while in recording pause mode.
The flashing “REC” on the display becomes quicker and
the tape runs without recording (blank spaces are
inserted).
“REC” flashes quickly
After 4 seconds, the tape pauses (recording pause
mode).
“REC” flashes slowly
To make blank spaces less than 4 seconds, press the
O REC/REC MUTE button again while “REC” flashes
auicklv.
To make blank spaces more than 4 seconds, press the
● REC/REC MUTE button again after the deck enters
~ a se mode. Each time it is pressed, a 4-
second blank space is added.
Press the II button to resume recording.
To erase a recording
1 Insert the tape to be erased into deck 2.
2 Press the TAPE/DECK 1/2 button to select deck 2.
3 Set the tape to the point where the erasure is to be
started.
4 Press the
● REC/REC MUTE button to start the erasure.
Sound adjustment during recording
The output volume and tone of the speakers or headphones
may be freely varied without affecting the level of the
recording.
ENGLISH 11
DUBBING A TAPE MANUALLY DUBBING THE WHOLE TAPE
2
3
Preparation
● Set the tape to the point where recording will start.
● Note that recording will be done on one side of the tape
only.
1
2
3
4
5
Press the TAPE/DECK 1/2 button.
Insert the original tape into deck 1 and the tape
to be recorded on into deck 2.
Insert each tape with the side to be played back first or
recorded on facing up.
Press the TAPE/DECK 1/2 butlon to select deck
1.
Press the REV MODE button to select the
reverse mode on deck 1.
To play one side only, select =.
To play both sides, select (1 or C=).
Press the ● REC/REC MUTE button to start
recording.
“REC” on the display flashes.
Playing and recording start simultaneously.
To stop dubbing
Press the
■ button.
1
1
4
9
3
2
This function allows you to make exact copies of the original
tape.
NOTE
● Prepare a tape which is longer than the original one or
which has the same length. Otherwise recording may be
cut short.
● Dubbing does not start from a point halfway in the tape.
● Note that recording will be done on one side of the tape
only.
1
2
3
4
Insert the original tape into deck 1 and the tape
to be recorded on into deck 2.
Insert each tape with the side to be played back or
recorded on facing up.
Press the TAPE/DECK 1/2 button to select deck
1.
Press the REV MODE button to select Z,
Exact copies of the original tape cannot be made if a
reverse mode other than = is selected.
Press the SYNCHRO DUBBING button to start
recording.
The tapes are rewound to the beginning, and recording
starts.
When recording finishes, both decks enter the recording
stop mode.
To record on the other side, turn over the tapes in both
decks then press the SYNCHRO DUBBING button.
To stop dubbing
Press the
■ button.
NOTE
Recording is inhibited if the erasure prevention tab for the
side of the tape facing up is broken off.
12 ENGUSH
Al EDIT RECORDING
The Al edit function enables CD recording without worrying
about tape length and track length. When a CD is inserted,
the unit automatically calculates track lengths. If necessary,
the order of tracks is rearranged so that no track is cut short.
(Al: Artificial Intelligence)
NOTE
Al edit recording will not start from a point halfway into the
tape. The tape must be recorded from the beginning of
either side.
Use the remote control,
Insert the tape into deck 2.
Insert the tape with the side to be recorded on first (front
side) facing up.
Press the FUNCTION button repeatedly until
~ is displayed and load the disc.
Press the EDIT/CHECK button once while
pressing the SHIFT button.
Al (Ai edit)
Each time it is pressed, the display changes as follows.
T
Al (Al edit) -+ P (Programmed edit)
Press the numbered buttons to designate the
tape length.
10 to 99 minutes can be specified.
Example: When using a 60-minute tape, press the 6 and
Obuttons.
In a few seconds, the microcomputer determines the
tracks to be recorded on each side of the tape.
● The - and - buttons are also available to
designate the tape length.
Tape side (front side)
Tape length
Number of
Remaining
programmed time of
tracks front side
!5
6
;7
Press the O TAPE REC/REC MUTE button and
then press the > button within 2 seconds to
start recording.
The tape is rewound to the beginning of the front side,
the lead segment is played through for 10 seconds, and
recording starts. When the last track programmed for
the front (4) is finished, deck 2 enters the recording
stop mode. After entering the recording stop mode, go to
the next step.
Press the EDIT/CHECK button while pressing
the SHIFT button to display the program for the
second recording and turn over the tape in
deck 2.
E is
displayed.
Press the ● TAPE REC/REC MUTE button and
then press the P button within 2 seconds to
start recording on the second
side.
To stop recording
Press the
■ button. Recording and CD play stop
simultaneously.
To clear the edit program
F)ress the 9 button twice to return to the basic operation
clisplay.
To check the order of the programmed track numbers
E3eforerecording, press the EDIT/CHECK button while
pressing the SHIFT button to select the front (+) or back
(>) side, and press the < or - button repeatedly.
Tape side
<: front side
F: back side
Track num~er
Pr~gram number
Time on-cassette tapes and editing time
The actual cassette recording time is usually a little longer
than the specified recording time printed on the label. This
unit can program tracks to use the extra time. When the total
recording time is a little longer than the tape’s specified
recording time after editing, the display shows the extra time
(without a minus mark), instead of the time remaining on the
tape (with the minus mark).
NOTE
● Recordina is inhibited if the erasure rxevention tab for the
side of th; tape facing up is broken off.
● The Al edit function cannot be used with discs containing
31 tracks or more.
ENGLISH 13
To change the program of each side
Press the EDIT/CHECK button while pressing the SHIFT
button to select the front (+) or back (E) side, and press
the 9 button to clear the program of the selected side. Then
program tracks again.
To clear the edit program
Press the
■ button to return to the basic operation display.
NOTE
Recording is inhibited if the erasure prevention tab for the
side of the tape facing up is broken off.
About cassette tapes
● To prevent accidental erasure, break off the plastic
tabs on the cassette tape with a screwdriver or other
pointed tool after recording.
Side A
Tab for side A
To record on the tape again, cover the tab openings witl
adhesive tape, etc.
● 120-minute or longer tapes are extremely thin and
easily deformed or damaged. They are not
recommended.
● Take up any slack in the tape with a pencil or similar
tool before use. Slack tape may break or jam in the
mechanism.
ENGLISH 15
SETTING THE CLOCK
SETTING THE TIMER
2-,
1 ... .....
h
1
2
3
Press the CLOCK button.
(12-hour standard)
Turn the VOLUME/TIMER control to adjust the
clock.
For quick adjustment, turn the control quickly.
Press the ENTER button to complete the
setting.
@on
the display disappears and the clock starts from
00 seconds.
To display the current time
Press the CLOCK button.
To return to the operation display, press the CLOCK button
or one of the function buttons.
To switch to the 12/24-hour standard
While the clock is displayed, press the
■ button.
Setting the clock with the remote control
1 Press the CLOCK button while pressing the SHIFT
button.
2 Press the < or ~ button to adjust the clock.
For quick adjustment, keep the button pressed.
3 Press the 1I SET button to complete the setting.
If the clock display flashes while the power is off
This is caused by a power interruption. The current time
needs to be reset.
If power is interrupted for more than approximately 12 hours,
all settings stored in memory after purchase need to be
reset.
The unit can be turned on at a s~ecified time everv dav with
the built-in timer.
. .
Preparation
Make sure the clock is set correctly.
1
2
3
4
5
6
Press the TIMER button once.
Turn the VOLUME/TIMER control to adjust the
timer-on time.
Press the ENTER button to designate the timer-
on time.
Flashing 0 on the display stops.
Prepare the source.
To listen to a CD,
press the CD button and load the
disc.
To listen to a tape, press the TAPE button and insert
the tape into deck 1 or 2.
To listen to the radio, press the TUNER button and
tune in a station.
Turn the VOLUME/TIMER control to set the
volume.
Press the POWER button to turn the unit off.
@ remains on the display (timer-standby mode).
When the timer-on time is reached, the unit turns on and
play begins with the selected source.
The unit will turn off automatically after 180 minutes.
To check the timer-on time
Press the TIMER button. The timer-on time is displayed with
@lflashing.
After checking the time, press the ENTER button to restore
the display.
16 ENGLISH
Setting the timer with the remote control
1 Press the TIMER button while pressing the SHIFT button.
2 Press the - or - button to adjust the timer-on time.
3 Press the 11 SET button to designate the timer-on time.
4 Press the FUNCTION button repeatedly and prepare the
source,
5 Press the VOLUME buttons to adjust the volume.
6 Press the POWER button to turn the unit off.
TIMER RECORDING
Timer recording is applicable for TUNER source only.
Press the TIMER button twice so that QIREcappears on
the display.
Repeat the steps shown above from step 2 and insert the
tape to be recorded on into deck 2.
To cancel timer standby mode
Press the TIMER button repeatedly so that ~ or @REc
disappears on the display.
To restore the timer standby mode, press again to display @
or OREc.
Using the unit while the timer is set
You can use the unit normally after setting the timer.
After use, repeat steps 4 to 6.
NOTE
Timer playback and timer recording will not begin unless the
power is turned off.
SETTING THE SLEEP TIMER
The unit can be turned off automatically at a specified time.
‘f
AZ
Press the SLEEP button.
Within 4 seconds, press the SLEEP button
repeatedly to select the time until the power is
turned off.
Each time it is pressed, the time changes between 30
and 180 minutes as follows.
~30+60+ 90+120 +150+ 180+ OFF (off)n
To check the time remaining until the power is turned off
Press the SLEEP button once.
The remaining time is displayed for 4 seconds.
ENGLISH 17
CARE AND MAINTENANCE
SPECIFICATIONS
Occasional care and maintenance of the unit and the
software are needed to optimize the performance of your
unit.
To clean the cabinet
Use a soft and dry cloth.
If the surfaces are extremely dirty, use a soft cloth lightly
moistened with mild detergent solution. Do not use strong
solvents, such as alcohol, benzine or thinner as these could
damage the finish of the unit.
To clean the heads and tape paths
After every 10 hours of use, clean the heads and tape paths
with a head cleaning cassette or cotton swab moistened with
cleaning fluid or denatured alcohol. (These cleaning kits are
commercially available.)
When cleaning with a cotton swab 0, wipe the heads 0 and
0, capstans 0, and pinchroilers 0.
nmu
/
f
After cleaning the heads and tape paths with a liquid head
cleaning cassette or a moistened swab, wait until the
cleaned parts are completely dry before inserting the tapes.
To demagnetize the heads
The heads may become magnetized after long-term use.
This may narrow the output range of recorded tapes and
increase noise. After 20 to 30 hours use, demagnetize the
heads with any commercially available demagnetizer.
Care of discs
● When a disc becomes dirty, wipe the disc from the center
out with a cleaning cloth.
● After playing a disc, store the disc in its case. Do not leave
the disc in places that are hot or humid.
FM tuner section
Tuning range 87.5 MHz to 108 MHz
Antenna
Rod antenna
AM tuner section
Tuning range
530
kHz to 1710 kHz (10 kHz step)
531 kHz to 1602 kHz (9 kHz step)
Antenna
Ferrite bar antenna
Cassette deck section
Track format
4 tracks, 2 channels stereo
Frequency response
Normal tape: 50 Hz – 12500 Hz
Recording system
AC bias
Heads
Deck 1: Playback head x 1
Deck 2: Recording/playback head x
1, Erasure head x 1
Compact disc player section
Laser
Semiconductor laser (1= 780 nm)
D-A converter
1 bit dual
General
Speakers
100 mm cone type
Power output
2.5 W + 2.5 W (EIAJ 7 Q DC)
output
PHONES (stereo minijack)
Power requirements
DC 12 V using eight size C (R14)
batteries
120VAC
60 HZ
Power consumption 18W
Dimensions of main unit (W x H x D)
450 x 184x 249 mm
(173/, x 71/4x97/8in.)
Weight of main unit 4.3 kg (9 Ibs. 8 OZ.)
● Specifications and external appearance are subject to
change without notice.
● Specifications, trade mark and model name are marked on
the rear of the unit.
COPYRIGHT
Please check the laws on copyright relating to recordings
from discs, radio or external tapes for the country in which
the machine is being used.
Care of tapes
“Store tapes in their cases after use.
● Do not leave tapes near magnets, motors, television sets,
or any source of magnetism. This will downgrade the
sound quality and cause noise.
● Do not expose tapes to direct sunlight, or leave them in a
car parked in direct sunlight.
18 ENGLISH
TROUBLESHOOTING GUIDE
PARTS INDEX
Ifthe unit fails to perform as described in these Operating
Instructions, check the following guide.
GENERAL
There is
no sound.
● Is the AC cord connected properly?
● Was an incorrect function button pressed?
An erroneous display or a malfunction occurs.
+ Reset the unit as stated below.
TUNER
SECTION
The reception contains noise interferences or the sound
is distorted.
● ISthe unit picking up external noise or multipath distortion?
+ Change the orientation of the antenna or the unit.
+ Move the unit away from other electrical appliances,
CASSETTE DECK SECTION
The tape does not run.
● Is the deck in pause mode? (-+ page 10)
The sound is off-balance or not adequately high.
● Is the playback head dirty? (+ page 18)
Recording is not possible.
● Is the erasure prevention tab on the tape broken off?
(+ page15)
● Is the recording head dirty? (-+ page 18)
Erasure is not possible.
● Is the erasure head dirty? (+ page 18)
● Is a metal tape or CrOz tape being used?
High frequency sound is not emitted.
● Is the recording/playback head dirty? (--+ page 18)
The tape is not removed.
+ If you try to use the unit when the batteries are depleted,
the tape may stop during play or recording, and the
cassette holder will not open.
Should this occur, replace the batteries with new ones or
connect the supplied AC cord to the unit, then remove
the tape.
CD PLAYER SECTION
The CD player does not play.
oIs the disc correctly inserted? (+ page 8)
* Is the disc dirty? (+ page 18)
oIs the lens affected by condensation?
+ Wait approximately one hour and try again.
Instructions about each part on the main unit or remote
control are indicated on the pages listed below.
(in alphabetic order)
Parts
BIAND/MODE TUNER
CD
~ CD OpEN
M CLEAR
CLOCK
44 DOWN
EiDIT/CHECK
ENTER
EQ
FUNCTION
OPEN
PHONES
POWER
“<~ (>) PRESET/DIR
PRGM
QSOUND
f3ANDOM
@ REC/REC MUTE
REPEAT
REV MODE
11 SET
SHIFT
SLEEP
SYNCHRO DUBBING
● TAPE REC/REC MUTE
TAPE/DECK 1/2
T-BASS
TIMER
TUNER/BAND
> UP
VOLUME/TIMER
o-9, +10
3-MODE EQUALIZER
Pages
6
8
8
7,8,10
16
6,8,10
8,13,14,15
16
5
4
10
5
5
7,8,10
9
5
9
11
9
10
7,8,10
4
17
12
11
10
5
16
6
6,8,10
5,16
7, 8
5
To reset
If an unusual condition occurs in the display window or the
cass~tte decks, reset the unit as follows.
1 Press the POWER button to turn off the power.
2 Press the POWER button to turn the power back on while
pressing the
■ CLEAR button. Everything stored in
memory after purchase is canceled.
If the power cannot be turned off in step 1 because of a
malfunction, reset by disconnecting the AC cord and repeat
step 2.
ENGLISH I 9
ADVERTENCIA
PARA REDUCIR EL RIESGO DE
INCENDIOS O SACUDIDAS ELECTRICAS,
NO EXPONGA ESTE APARATO A LA
LLUVIA NI A LA HUMEDAD.
1A= Al
“CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.”
Explication de Ios simbolos graficos:
El
simbolo del relampago con la punta en flecha
A
dentro de un triangulo equilat ero, sirve para alertar
al usuario de la presencia de “tension peligrosa”
sin aislar en el interior de la caja del aparato, la
cual podra ser 10suficientem ente fuerte como para
suponer un riesgo de sacudida eiectrica a perso-
nas.
A
El signo de exclamation dentro del un tri&rgulo
equilatero sirve para alertar al usuario de la
presencia de instrucciones importances de
operation y manteni miento (servicio) en la
●
information que acompaha al aparato.
REGISTRO DEL PROPIETARIO
Anote el nfimero del modelo (que se encuentra en la parte inferior del
aparato) y el ntimero de serie (dentro del compartimiento de Ias pilas)
en e] espacio provisto a continuation.
Encaso de problemas o averfas,
comunique estos numeros a su concesionario AlWA.
‘ode’m”de’om ‘odeseriem
PRECAUCIONES
Leer detenida y completamente Ias instrucciones de
funcionamiento antes de manejar el aparato. Asegurarse de
conservar estas instrucciones de funcionamiento como
referencia en el future. Deben seguirse estrictamente todas
Ias advertencias y precauciones indicadas en este manual,
asf como Ios consejos siguientes relacionados con la
seguridad.
Instalacion
1
2
3
4
5
6
7
8
Agua y humedad – No utilizareste aparatocercadel
agua, comocercade una baflera, Iavabo,pilade la
cocina,Iavadero,en sotanoshumedos,piscinaso Iugares
similares.
Caior – No usareste aparatocerca de fuentesde calor,
comorejillasde calefaccion,estufasu otrosaparatosque
generancalor.No debe usarse
en sitios en Ios que la
temperature es inferior a 5°C (41“F) o superior a 35°C
(95”F).
Superficie de montaje – Colocarel aparatosobreuna
superficieplanay nivelada.
Ventilation – Esteaparatodebe colocarsede manera
que tenga un espacio adecuado a su alrededor para que
pueda disiparse el calor. Dejar un espacio de 10 cm (4
pulg.) desde la parte posterior y superior del aparato y 5
cm (2 pulg.) en cada Iado.
- No colocar el aparato sobre una cama, alfombra o
superficie similar que pueda bloquear Ias rejillas de
ventilation.
- No instalar el aparato en una Iibreria, estanteria o
mueble donde la ventilation sea deficient.
Entrada de objetos y agua – Tener cuidado de que no
entren objetos extraiios ni Iiquidos por Ias rejillas de
ventilation.
Carros y mostradores - Cuandoel
aparatose
coloque sobre un carro o
mostrador, es necesario tener cuidado con
@
● L
10smovimientos.
w
Las paradas bruscas, fuerza excesiva y
. .
superficies desiguales pueden hater que
e] aparato se caiga o que el carro vuelque.
Condensation – La Iente del Iector de CD puede
acumular humedad cuando:
- El aparato se mueve desde un sitio frio a uno caliente
- Se acaba de encender la calefaccion
- El aparato se usa en una habitation muy htimeda
- El aparato se enfria con un acondicionador de aire
El aparato pudiera no funcionar correctamente cuando se
ha condensado humedad en su interior. Si ocurriera,
dejarlo apagado unas horas e intentar usarlo de nuevo.
Montaje en la pared o techo – El aparato no debe
monta;se en uria pared ni colgarse dueltecho a menos
que se especifique asi en Ias instrucciones de
funcionamiento.
Alimentacion electrica
1
2
Fuentes de alimentacion – Utilizarlocon pilaso
corriente alterna de la red, como se especifica en Ias
instrucciones de manejo y se indica en el aparato.
Polarization – Como medidade seguridad,algunos
aparatosestan equipadoscon enchufespolarizadosen el
cable de alimentacionque puedensolamenteinsertarse
en unsentidotinicodentrodel enchufede la pared.Si
fuera dificilo imposibleinsertarel enchufedel cablede
alimentaciondentrodel tomacorrientes,inviertael sentido
de insertiondel enchufey vuelvaa intentarconectarlo.Si
sigue siendo dificil insertarlo en et tomacorrientes, Ie
rogamos Ilame a un tecnico de servicio calificado para
que repare o cambie el tomacorrientes. Para evitar que la .
20 E.SPA~OL
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56

Aiwa CSD-EL50 Operating Instructions Manual

Aiwa
Marque
Aiwa
Modèle
CSD-EL50
Catégorie
Lecteurs de cassettes
Taper
Operating Instructions Manual
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents