115V, 60 Hz
Made in China
Fabriqué en Chine
Hecho en China
Haier America
New York, NY 10018
Printed in China
HC61F/HC92F/HC125F
Issued: June - 04
IMPORTANT
Do Not Return This Product To The Store
If you have a problem with this product, please contact the "Haier Customer
Satisfaction Center" at 1-877-337-3639.
DATED PROOF OF PURCHASE REQUIRED FOR WARRANTY SERVICE
IMPORTANT
Ne pas Réexpédier ce Produit au Magasin
Pour tout problème concernant ce produit, veuillez contacter le service des
consommateurs ‘Haier Customer Satisfaction Center’ au 1-877-337-3639.
UNE PREUVE D’ACHAT DATEE EST REQUISE POUR BENEFICIER DE LA GARANTIE.
IMPORTANTE
No regrese este producto a la tienda
Si tiene algún problema con este producto, por favor contacte el "Centro de Servicio al
Consumidor de Haier" al 1-877-337-3639 (Válido solo en E.U.A).
NECESITA UNA PRUEBA DE COMPRA FECHADA PARA EL SERVICIO DE LA GARANTIA
Part #RF-9999-184
Beverage Center
HC61F
HC92F
HC125F
(HC92F)
Minibar
User Manual-
Guide de l’Utilisateur-
(Las funciones pueden
variar según el modelo)
Manual del Usuario-
(Features may vary by model)
(Les caractéristiques peuvent
varier en fonction du modèle)
Model #
Modèle
Para Modelo de
Refrigerador de Bebidas
SAFETY PRECAUTIONS
Read all of the instructions before using this appliance. When using this
appliance, always exercise basic safety precautions, including the follow-
ing:
1) Use this appliance only for its intended purpose as described in this use
and care guide.
2) This beverage center must be properly installed in accordance with the
installation instructions before it is used. See grounding instructions in the
installation section.
3) Never unplug your beverage center by pulling on the power cord.
Always grasp the plug firmly and pull straight out from the outlet.
4) Repair or replace immediately, all electric service cords that have become
frayed or otherwise damaged. Do not use a cord that shows cracks or
abrasion damage along its length, the plug or the connector end.
5) Unplug your beverage center before cleaning or before making any
repairs. Note: If for any reason this product requires service, we strongly
recommend that a certified technician performs the service.
6) If your old beverage center is not being used, we recommend that you
remove the doors and leave the shelves in place. This will reduce the
possibility of danger to children.
7) This beverage center should not be recessed or built-in an enclosed
cabinet. It is designed for freestanding installation only.
8) Do not operate your beverage center in the presence of explosive fumes.
SAVE THESE INSTRUCTIONS
For Future Reference
1
English
2
Thank you for using our Haier
product. This easy-to-use manual will
guide you in getting the best use of
your beverage center.
Remember to record the model and
serial number. They are on a label in
back of the beverage center.
Model number
Serial number
Date of purchase
Staple your receipt to your manual.
You will need it to obtain warranty service.
DANGER
Risk of child entrapment. Before you throw away your old beverage center,
take off the doors. Leave the shelves in place so that children may not easily
climb inside.
English
Table Of Contents
PAGE
Safety Precautions ..........................................................................1
Parts And Features ..........................................................................4
Installing Your Beverage Center....................................................5
Unpacking Your Beverage Center ............................................................5
Installing Door Handle ............................................................................5
Leveling Your Beverage Center ................................................................5
Proper Air Circulation ............................................................................5
Electrical Requirements............................................................................6
Use of Extension Cords ..........................................................................6
Install Limitations ....................................................................................6
Door Alignment......................................................................................7
Door Reversal.........................................................................................8
Beverage Center Features And Use..................................................10
General Features..................................................................................10
Beverage Center Interior Shelves ..........................................................10
Normal Operating Sounds....................................................................12
Proper Beverage Center Care and Cleaning............................13
Cleaning and Maintenance ..................................................................13
Power Interruptions ..............................................................................14
Vacation and Moving Care ..................................................................14
Troubleshooting..............................................................................15
Warranty Information ..................................................................16
English
3
Parts And Features
1. Full-Width Storage Shelf (style
and quantity vary with model)
2. See-through Glass Door
3. Handle (type varies per model)
4. Interior Light (not in all models)
5. Temperature Control
(location varies per model,
refer to page 10)
6. Removable Wine Rack
English
4
1
2
3
4
(HC61F)
6
5
4
5
6
fig. # 1
1. Remove all packaging material. This includes the foam base and all
adhesive tape holding the beverage center accessories inside and
outside.
2. Inspect and remove any remains of packing, tape or printed
materials before powering on the beverage center.
1. Match the two screw holes in the handle to the
pre-drilled holes on the left side of the door as you
are looking at it.
2. Using a Phillips Head Screwdriver insert and tighten
the two screws to attach the handle to the unit.
• Your beverage center has leveling legs which are located at the bottom
of your beverage center. After properly placing your beverage center in
its final position, you can level your beverage center.
• Leveling legs can be adjusted by turning them clockwise to raise your
beverage center or by turning them counterclockwise to lower your
beverage center. The beverage center door will close easier when the
leveling legs are extended.
• Also, there is an adjustable support for the lower door hinge. (see fig.5)
After leveling the Beverage Center, adjust the hinge support, up or down
as needed until it rests on the surface on which that unit is placed.
• To assure your beverage center works at the maximum efficiency it
was designed for, you should install it in a location where there
is proper air circulation and electrical connections.
• The following are recommended clearances around the beverage center:
Sides……………3/4 "(19mm)
Top....................2" (50mm)
Back..................2" (50mm)
Installing Your Beverage Center
Unpacking Your Beverage Center
Proper Air Circulation
Leveling Your Beverage Center
5
English
Installing Handle (not available on all models) (see fig. #1)
English
Electrical Requirement
• Make sure there is a suitable power Outlet (115 volts, 15 amps outlet)
with proper grounding to power the beverage center.
• Avoid the use of three plug adapters or cutting off the third grounding in
order to accommodate a two plug outlet. This is a dangerous practice
since it provides no effective grounding for the beverage center and
may result in shock hazard.
• Avoid the use of an extension cord because of potential safety hazards
under certain conditions. If it is necessary to use an extension cord, use
only a 3-wire extension cord that has a 3-blade grounding plug and a
3-slot outlet that will accept the plug. The marked rating of the extension
cord must be equal to or greater than the electrical rating of the
appliance.
• Do not install your beverage center in any location not properly
insulated or heated e.g. garage etc. Your beverage center was not
designed to operate in temperature settings below 55˚ Fahrenheit.
• Select a suitable location for the beverage center on a hard even surface
away from direct sunlight or heat source e.g. radiators, baseboard
heaters, cooking appliances etc. Any floor unevenness should be
corrected with the leveling legs located at the bottom.
Install Limitations
6
Use of Extension Cords
7
1. Remove hinge cover screw.
2. Remove the top hinge cover.
3. Loosen the top hinge screws using a Phillips Head Screwdriver.
4. Adjust the door or put a spacer in between and then tighten the screws.
5. Replace the top hinge cover.
Door Alignment (see fig. # 2)
fig. # 2
English
English
8
Reversing the Door Hinge
1. Using a Phillips Head Screwdriver remove the screws from the door
handle. Place the screws and handle to the side. (See fig. #1)
2. Remove the top hinge cover screw and then remove
the top hinge cover. (see fig. # 2)
3. Using a Phillips Head Screwdriver, loosen and remove the
screws holding the top hinge in place. (see fig. # 2)
4. Remove the top hinge and carefully lift off the door.
5. Remove the screw hole plug from the opposite side and
insert the plug in the screw hole openings of the just
removed screws. (see fig. # 3)
6. Unscrew the door pin from the bracket of the lower
hinge by turning counter clockwise. Move the pin to the
opposite hole and tighten. (see fig. # 4) Tilt unit slightly towards back
and remove the lower hinge support. (see fig. # 5)
7. Loosen the screws holding the lower hinge bracket
and remove the hinge.(see fig. # 4)
8. Align the holes in the lower hinge bracket to the
corresponding holes in the opposite side of the cabinet.
Insert and tighten the screws.(see fig. # 4) Tilt unit slightly back to
replace the lower hinge support. Adjust up or down as needed until it
is just touching the surface on which that unit is placed. (see fig. # 5)
9. Align the bottom hole on the left side of the door with the
pin of the lower hinge and slide into place.
fig. # 3
screw hole plugs
10. Align the pin of the top hinge with top hole on the left
side of the door and push into place. Replace the screws in the
upper hinge bracket but do not tighten all the way. (see fig. # 2)
11. Make sure the door closes easily but forms a tight seal.
Adjust the door as needed. Once you are satisfied with the door
alignment, completely tighten the upper door hinge screws.
12. Replace the hinge cover, insert the screw and
tighten completely. (see fig. # 2)
13. Remove the screw hole plugs from the opposite side. Place the plugs in
the screw holes on the side from which the handle was removed.
Align the screw holes on the handle with those on the door trim. Using
a Phillips Head Screwdriver insert and tighten the 2 screws. (see fig.
#1)
14. If the door does not close properly, refer to the
section titled “Door Alignment”.
fig. # 4
English
9
door pin
lower hinge bracket
spacet
fig. # 5
lower hinge support
lower hinge
Beverage Center Features And Use
To remove or replace a full-width slide-out shelf:
(see fig. # 6)
1. Gently tilt the shelf up and slide forward until the shelf has been
completely removed.
2. To replace the shelf, gently slide the shelf back.
General Features
Adjustable temperature dial:
Your beverage center will automatically
maintain the temperature level you
select. The temperature control dial has
7 settings plus off. 1 is the warmest. 7 is
the coldest. Turning the dial to OFF stops
cooling in the beverage center. At first,
set the dial to 4 and allow 24 hours to
pass before adjusting the temperature to
your needs.
(Note: If the beverage center
has been placed in a horizontal
or tilted position for any period
of time wait 24 hours before
plugging the unit in.)
Beverage Center Interior Shelves
(shelves will vary per model purchased)
fig. # 6
English
10
(location varies by model)
1
2
3
4
5
6
7
0
c
o
o
l
e
r
6
5
4
located on the rear, near bottom
(for models HC61F and HC92F)
located on interior of unit on right side
(for model HC125F)
English
11
Light (not on all models)
• To replace burnt-out bulbs, remove the temperature control knob by
pulling it out (see fig. # 8a). Carefully pull the plastic light cover to the
left and remove. Unscrew the bulb and replace it with a new one (use
bulbs of 15 watts or less). To replace cover, insert the back slots into the
casing (see fig. # 8b). Align the front and push the control knob back in.
6
5
4
fig. # 8a
fig. # 8b
To use the interior flip shelf: (quantity will vary by model)
(see fig. # 7)
1. Simply flip the shelf as shown in the diagram. This is designed to
give you extra storage for tall bottles.
fig. # 7
English
12
• Boiling water, gurgling sounds or slight vibrations that are the result of
the refrigerant circulating through the cooling coils.
• The thermostat control will click when it cycles on and off.
Normal Operating Sounds You May Hear
13
English
Warning:
To avoid electric shock always unplug your
beverage center before cleaning. Ignoring this
warning may result in death or injury.
Caution: Before using cleaning products, always read and
follow manufacturer’s instructions and warnings to
avoid personal injury or product damage.
General:
•Prepare a cleaning solution of 3-4 tablespoons of
baking soda mixed with warm water. Use sponge or
soft cloth, dampened with the cleaning solution, to
wipe down your beverage center.
• Rinse with clean warm water and dry with a soft cloth.
• Do not use harsh chemicals, abrasives, ammonia,
chlorine bleach,concentrated detergents, solvents or
metal scouring pads. SOME of these chemicals may
dissolve, damage and/or discolor your beverage
center.
• Clean door gaskets every three months according to
general instructions. Gaskets must be kept clean and
pliable to assure a proper seal.
• Petroleum jelly applied lightly on the hinge side of
gaskets will keep the gasket pliable and assure a good
seal.
• Every 12 months, using either a soft brissel brush or
vacuum cleaner, clean dust, which has accumulated on
the coil. This will aid in the efficient operation of your
unit.
Proper Beverage Center Care
and Cleaning
Cleaning and Maintenance
Door Gaskets:
Rear Condensor Coil:
• Occasionally there may be power interruptions due to thunderstorms or
other causes. Remove the power cord from AC outlet when a power
outage occurs. When power has been restored, replug power cord to
AC outlet.
• For long vacations or absences, empty contents from beverage center,
move the temperature DIAL to the OFF position and clean the beverage
center and door gaskets according to "General cleaning" section. Prop
doors open, so air can circulate inside.When moving always move the
beverage center vertically. Do not move with the unit lying down.
Possible damage to the sealed system could occur.
English
14
Power Interruptions
Vacation and Moving Care
15
English
Beverage Center Does Not Operate
• Check if thermostat control is not in the “OFF” position.
• Check if beverage center is plugged in.
• Check if there is power at the ac outlet, by checking the circuit breaker.
Temperature appears too warm
• Frequent door openings.
• Allow time for recently added beverages to reach proper
temperature.
• Check gaskets for proper seal.
• Adjust temperature control to cooler setting.
Temperature is too cold
• If temperature control setting is too cold, adjust to a warmer setting
and allow several hours for temperature to adjust.
Beverage Center runs too frequently
• This may be normal to maintain constant temperature during
high temperature and humid days.
• Doors may have been opened frequently or for an extended
period of time.
• Check gasket for proper seal.
• Check to see if doors are completely closed.
Moisture build up on interior or exterior
of the beverage center:
• This is normal during high humidity periods.
• Prolonged or frequent door openings.
• Check door gaskets for proper seal.
Beverage Center door does not shut properly:
• Level the beverage center.
• Re-align beverage center door.
• Check for blockages.
TroubleShooting
English
16
Limited Warranty
What is covered and for how
long?
This warranty covers all defects in
workmanship or materials for a period
of:
12 months labor (carry in only)
12 months parts (carry in only)
5 years sealed system
(carry in only)
The warranty commences on the date
the item was purchased and the original
purchase receipt must be presented to
the authorized service center before
warranty repairs are rendered.
EXCEPTIONS: Commercial or
Rental Use warranty
90 days labor (carry-in only)
90 days parts
No other warranty applies
What is covered.
1. The mechanical and electrical parts,
which serve as a functional, purpose
of this appliance for a period of 12
months. This includes all parts except
finish, and trim.
2. The components of the sealed system
e.g. hermetic compressor, condenser
and evaporator from manufacturing
defects for a period of 5 years from
the date of purchase. Any damages
to such components caused by
mechanical abuse or improper
handling or shipping will not be
covered.
What will be done?
1. We will repair or replace, at our
discretion any mechanical or
electrical part which proves to be
defective in normal usage during the
warranty period so specified.
2. There will be no charge to the
purchaser for parts and labor on any
covered items during the initial 12
month period. Beyond this period
only parts are covered in the
remaining warranty. Labor is not
provided and must be paid by
the customer.
3. Contact your nearest authorized
service center. For the name of the
nearest service center please call
1-877-337-3639
THIS WARRANTY COVERS
APPLIANCES WITHIN THE
CONTINENTAL UNITED STATES,
PUERTO RICO AND CANADA.
IT DOES NOT COVER
THE FOLLOWING:
Damages from improper installation.
Damages in shipping.
Defects other than manufacturing.
Damage from misuse, abuse, accident,
alteration, lack of proper care and
maintenance or incorrect current or
voltage.
Damage from other than household use.
Damage from service by other than an
authorized dealer or service center.
Decorative trims or replaceable
light bulbs.
Transportation and shipping.
Labor (after the initial 12 months).
THIS LIMITED WARRANTY IS GIVEN IN
LIEU OF ALL OTHER WARRANTIES,
EXPRESSED OR, INCLUDING THE
WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR
PURPOSE
The remedy provided in this warranty is
exclusive and is granted in lieu of all
other remedies.
This warranty does not cover incidental
or consequential damages, so the above
limitations may not apply to you. Some
States do not allow limitations on how
long an implied warranty lasts, so the
above limitations may not apply to you.
This warranty gives you specific legal
rights, and you may have other rights,
which vary, from state to state.
Haier America
New York, NY 10018
MESURES DE SÉCURITÉ
Lisez attentivement toutes les instructions avant d’utiliser cet appareil. Lors
de son utilisation, suivez toutes les mesures de sécurité élémentaires, y com-
pris les mesures suivantes:
1) N’utiliser cet appareil que conformément à ce manuel d'utilisation et
d'entretien.
2) Avant son utilisation, cet appareil doit être installé conformément aux
instructions d’installation. Voir les instructions relatives au branchement
dans la section sur l’installation.
3) Ne jamais débrancher votre minibar en tirant sur le câble d’alimentation.
Toujours serrer fermement la fiche puis la retirer de la prise en la
maintenant bien droite.
4) Réparer ou remplacer immédiatement tous les câbles électriques usés ou
endommagés. Ne pas utiliser de cordon d’alimentation présentant des
craquelures ou des dommages dus à des frottements sur le câble
lui-même, sur la fiche ou sur le connecteur.
5) Débrancher le minibar avant de le nettoyer et avant toute réparation.
Remarque: si, pour une quelconque raison, vous devez faire réparer cet
appareil, nous vous conseillons vivement de faire appel à un technicien
agréé.
6) Si votre ancien minibar n’est plus utilisé, nous vous recommandons de
retirer les portes et de laisser les étagères en place. Cela réduira les
risques d’accident pour les enfants.
7) Ce minibar ne doit pas être renfermé ni encastré. Il est conçu pour être
utilisé sur pied.
8) Ne jamais utiliser le minibar en présence de gaz explosifs.
VEUILLEZ CONSERVER INSTRUCTIONS
afin de pouvoir les consulter de besoin
1
Français
Merci d’utiliser un produit Haier.
Suivez ce manuel d’instruction simple
d’utilisation pour obtenir le maximum
de votre minibar.
N’oubliez pas d’enregistrer les
numéros de modèle et de série. Ils se
trouvent sur une étiquette à l’arrière
de votre minibar.
Numéro de modèle
Numéro de série
Date d’achat
Veuillez agrafer votre facture avec votre manuel.
Vous en aurez besoin pour bénéficier de la garantie.
DANGER
Cet appareil présente un risque d'enfermement pour les enfants. Avant de
vous débarrasser de votre ancien minibar, veuillez enlever les portes. Laissez
les étagères en place afin que les enfants ne puissent pas grimper à l’in-
térieur.
2
Français
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
Haier HC125F Manuel utilisateur
- Catégorie
- Boissons glacées
- Taper
- Manuel utilisateur
dans d''autres langues
- English: Haier HC125F User manual
- español: Haier HC125F Manual de usuario