Haier HC61F Manuel utilisateur

115V, 60 Hz

Made in China

Fabriqué en Chine

Hecho en China

Haier America

New York, NY 10018

Printed in China

HC61F/HC92F/HC125F

Issued: June - 04

IMPORTANT

Do Not Return This Product To The Store

If you have a problem with this product, please contact the "Haier Customer

Satisfaction Center" at 1-877-337-3639.

DATED PROOF OF PURCHASE REQUIRED FOR WARRANTY SERVICE

IMPORTANT

Ne pas Réexpédier ce Produit au Magasin

Pour tout problème concernant ce produit, veuillez contacter le service des

consommateurs ‘Haier Customer Satisfaction Center’ au 1-877-337-3639.

UNE PREUVE D’ACHAT DATEE EST REQUISE POUR BENEFICIER DE LA GARANTIE.

IMPORTANTE

No regrese este producto a la tienda

Si tiene algún problema con este producto, por favor contacte el "Centro de Servicio al

Consumidor de Haier" al 1-877-337-3639 (Válido solo en E.U.A).

NECESITA UNA PRUEBA DE COMPRA FECHADA PARA EL SERVICIO DE LA GARANTIA

Part #RF-9999-184

Beverage Center

HC61F

HC92F

HC125F

(HC92F)

Minibar

User Manual-

Guide de l’Utilisateur-

(Las funciones pueden

variar según el modelo)

Manual del Usuario-

(Features may vary by model)

(Les caractéristiques peuvent

varier en fonction du modèle)

Model #

Modèle

Para Modelo de

Refrigerador de Bebidas

SAFETY PRECAUTIONS

Read all of the instructions before using this appliance. When using this

appliance, always exercise basic safety precautions, including the follow-

ing:

1) Use this appliance only for its intended purpose as described in this use

and care guide.

2) This beverage center must be properly installed in accordance with the

installation instructions before it is used. See grounding instructions in the

installation section.

3) Never unplug your beverage center by pulling on the power cord.

Always grasp the plug firmly and pull straight out from the outlet.

4) Repair or replace immediately, all electric service cords that have become

frayed or otherwise damaged. Do not use a cord that shows cracks or

abrasion damage along its length, the plug or the connector end.

5) Unplug your beverage center before cleaning or before making any

repairs. Note: If for any reason this product requires service, we strongly

recommend that a certified technician performs the service.

6) If your old beverage center is not being used, we recommend that you

remove the doors and leave the shelves in place. This will reduce the

possibility of danger to children.

7) This beverage center should not be recessed or built-in an enclosed

cabinet. It is designed for freestanding installation only.

8) Do not operate your beverage center in the presence of explosive fumes.

SAVE THESE INSTRUCTIONS

For Future Reference

1

English

2

Thank you for using our Haier

product. This easy-to-use manual will

guide you in getting the best use of

your beverage center.

Remember to record the model and

serial number. They are on a label in

back of the beverage center.

Model number

Serial number

Date of purchase

Staple your receipt to your manual.

You will need it to obtain warranty service.

DANGER

Risk of child entrapment. Before you throw away your old beverage center,

take off the doors. Leave the shelves in place so that children may not easily

climb inside.

English

Table Of Contents

PAGE

Safety Precautions ..........................................................................1

Parts And Features ..........................................................................4

Installing Your Beverage Center....................................................5

Unpacking Your Beverage Center ............................................................5

Installing Door Handle ............................................................................5

Leveling Your Beverage Center ................................................................5

Proper Air Circulation ............................................................................5

Electrical Requirements............................................................................6

Use of Extension Cords ..........................................................................6

Install Limitations ....................................................................................6

Door Alignment......................................................................................7

Door Reversal.........................................................................................8

Beverage Center Features And Use..................................................10

General Features..................................................................................10

Beverage Center Interior Shelves ..........................................................10

Normal Operating Sounds....................................................................12

Proper Beverage Center Care and Cleaning............................13

Cleaning and Maintenance ..................................................................13

Power Interruptions ..............................................................................14

Vacation and Moving Care ..................................................................14

Troubleshooting..............................................................................15

Warranty Information ..................................................................16

English

3

Parts And Features

1. Full-Width Storage Shelf (style

and quantity vary with model)

2. See-through Glass Door

3. Handle (type varies per model)

4. Interior Light (not in all models)

5. Temperature Control

(location varies per model,

refer to page 10)

6. Removable Wine Rack

English

4

1

2

3

4

(HC61F)

6

5

4

5

6

fig. # 1

1. Remove all packaging material. This includes the foam base and all

adhesive tape holding the beverage center accessories inside and

outside.

2. Inspect and remove any remains of packing, tape or printed

materials before powering on the beverage center.

1. Match the two screw holes in the handle to the

pre-drilled holes on the left side of the door as you

are looking at it.

2. Using a Phillips Head Screwdriver insert and tighten

the two screws to attach the handle to the unit.

• Your beverage center has leveling legs which are located at the bottom

of your beverage center. After properly placing your beverage center in

its final position, you can level your beverage center.

• Leveling legs can be adjusted by turning them clockwise to raise your

beverage center or by turning them counterclockwise to lower your

beverage center. The beverage center door will close easier when the

leveling legs are extended.

• Also, there is an adjustable support for the lower door hinge. (see fig.5)

After leveling the Beverage Center, adjust the hinge support, up or down

as needed until it rests on the surface on which that unit is placed.

• To assure your beverage center works at the maximum efficiency it

was designed for, you should install it in a location where there

is proper air circulation and electrical connections.

• The following are recommended clearances around the beverage center:

Sides……………3/4 "(19mm)

Top....................2" (50mm)

Back..................2" (50mm)

Installing Your Beverage Center

Unpacking Your Beverage Center

Proper Air Circulation

Leveling Your Beverage Center

5

English

Installing Handle (not available on all models) (see fig. #1)

English

Electrical Requirement

• Make sure there is a suitable power Outlet (115 volts, 15 amps outlet)

with proper grounding to power the beverage center.

• Avoid the use of three plug adapters or cutting off the third grounding in

order to accommodate a two plug outlet. This is a dangerous practice

since it provides no effective grounding for the beverage center and

may result in shock hazard.

• Avoid the use of an extension cord because of potential safety hazards

under certain conditions. If it is necessary to use an extension cord, use

only a 3-wire extension cord that has a 3-blade grounding plug and a

3-slot outlet that will accept the plug. The marked rating of the extension

cord must be equal to or greater than the electrical rating of the

appliance.

• Do not install your beverage center in any location not properly

insulated or heated e.g. garage etc. Your beverage center was not

designed to operate in temperature settings below 55˚ Fahrenheit.

• Select a suitable location for the beverage center on a hard even surface

away from direct sunlight or heat source e.g. radiators, baseboard

heaters, cooking appliances etc. Any floor unevenness should be

corrected with the leveling legs located at the bottom.

Install Limitations

6

Use of Extension Cords

7

1. Remove hinge cover screw.

2. Remove the top hinge cover.

3. Loosen the top hinge screws using a Phillips Head Screwdriver.

4. Adjust the door or put a spacer in between and then tighten the screws.

5. Replace the top hinge cover.

Door Alignment (see fig. # 2)

fig. # 2

English

8

Reversing the Door Hinge

1. Using a Phillips Head Screwdriver remove the screws from the door

handle. Place the screws and handle to the side. (See fig. #1)

2. Remove the top hinge cover screw and then remove

the top hinge cover. (see fig. # 2)

3. Using a Phillips Head Screwdriver, loosen and remove the

screws holding the top hinge in place. (see fig. # 2)

4. Remove the top hinge and carefully lift off the door.

5. Remove the screw hole plug from the opposite side and

insert the plug in the screw hole openings of the just

removed screws. (see fig. # 3)

6. Unscrew the door pin from the bracket of the lower

hinge by turning counter clockwise. Move the pin to the

opposite hole and tighten. (see fig. # 4) Tilt unit slightly towards back

and remove the lower hinge support. (see fig. # 5)

7. Loosen the screws holding the lower hinge bracket

and remove the hinge.(see fig. # 4)

8. Align the holes in the lower hinge bracket to the

corresponding holes in the opposite side of the cabinet.

Insert and tighten the screws.(see fig. # 4) Tilt unit slightly back to

replace the lower hinge support. Adjust up or down as needed until it

is just touching the surface on which that unit is placed. (see fig. # 5)

9. Align the bottom hole on the left side of the door with the

pin of the lower hinge and slide into place.

fig. # 3

screw hole plugs

10. Align the pin of the top hinge with top hole on the left

side of the door and push into place. Replace the screws in the

upper hinge bracket but do not tighten all the way. (see fig. # 2)

11. Make sure the door closes easily but forms a tight seal.

Adjust the door as needed. Once you are satisfied with the door

alignment, completely tighten the upper door hinge screws.

12. Replace the hinge cover, insert the screw and

tighten completely. (see fig. # 2)

13. Remove the screw hole plugs from the opposite side. Place the plugs in

the screw holes on the side from which the handle was removed.

Align the screw holes on the handle with those on the door trim. Using

a Phillips Head Screwdriver insert and tighten the 2 screws. (see fig.

#1)

14. If the door does not close properly, refer to the

section titled “Door Alignment”.

fig. # 4

English

9

door pin

lower hinge bracket

spacet

fig. # 5

lower hinge support

lower hinge

Beverage Center Features And Use

To remove or replace a full-width slide-out shelf:

(see fig. # 6)

1. Gently tilt the shelf up and slide forward until the shelf has been

completely removed.

2. To replace the shelf, gently slide the shelf back.

General Features

Adjustable temperature dial:

Your beverage center will automatically

maintain the temperature level you

select. The temperature control dial has

7 settings plus off. 1 is the warmest. 7 is

the coldest. Turning the dial to OFF stops

cooling in the beverage center. At first,

set the dial to 4 and allow 24 hours to

pass before adjusting the temperature to

your needs.

(Note: If the beverage center

has been placed in a horizontal

or tilted position for any period

of time wait 24 hours before

plugging the unit in.)

Beverage Center Interior Shelves

(shelves will vary per model purchased)

fig. # 6

English

10

(location varies by model)

1

2

3

4

5

6

7

0

c

o

l

e

r

6

5

4

located on the rear, near bottom

(for models HC61F and HC92F)

located on interior of unit on right side

(for model HC125F)

English

11

Light (not on all models)

• To replace burnt-out bulbs, remove the temperature control knob by

pulling it out (see fig. # 8a). Carefully pull the plastic light cover to the

left and remove. Unscrew the bulb and replace it with a new one (use

bulbs of 15 watts or less). To replace cover, insert the back slots into the

casing (see fig. # 8b). Align the front and push the control knob back in.

6

5

4

fig. # 8a

fig. # 8b

To use the interior flip shelf: (quantity will vary by model)

(see fig. # 7)

1. Simply flip the shelf as shown in the diagram. This is designed to

give you extra storage for tall bottles.

fig. # 7

English

12

• Boiling water, gurgling sounds or slight vibrations that are the result of

the refrigerant circulating through the cooling coils.

• The thermostat control will click when it cycles on and off.

Normal Operating Sounds You May Hear

13

English

Warning:

To avoid electric shock always unplug your

beverage center before cleaning. Ignoring this

warning may result in death or injury.

Caution: Before using cleaning products, always read and

follow manufacturer’s instructions and warnings to

avoid personal injury or product damage.

General:

•Prepare a cleaning solution of 3-4 tablespoons of

baking soda mixed with warm water. Use sponge or

soft cloth, dampened with the cleaning solution, to

wipe down your beverage center.

• Rinse with clean warm water and dry with a soft cloth.

• Do not use harsh chemicals, abrasives, ammonia,

chlorine bleach,concentrated detergents, solvents or

metal scouring pads. SOME of these chemicals may

dissolve, damage and/or discolor your beverage

center.

• Clean door gaskets every three months according to

general instructions. Gaskets must be kept clean and

pliable to assure a proper seal.

• Petroleum jelly applied lightly on the hinge side of

gaskets will keep the gasket pliable and assure a good

seal.

• Every 12 months, using either a soft brissel brush or

vacuum cleaner, clean dust, which has accumulated on

the coil. This will aid in the efficient operation of your

unit.

Proper Beverage Center Care

and Cleaning

Cleaning and Maintenance

Door Gaskets:

Rear Condensor Coil:

• Occasionally there may be power interruptions due to thunderstorms or

other causes. Remove the power cord from AC outlet when a power

outage occurs. When power has been restored, replug power cord to

AC outlet.

• For long vacations or absences, empty contents from beverage center,

move the temperature DIAL to the OFF position and clean the beverage

center and door gaskets according to "General cleaning" section. Prop

doors open, so air can circulate inside.When moving always move the

beverage center vertically. Do not move with the unit lying down.

Possible damage to the sealed system could occur.

English

14

Power Interruptions

Vacation and Moving Care

15

English

Beverage Center Does Not Operate

• Check if thermostat control is not in the “OFF” position.

• Check if beverage center is plugged in.

• Check if there is power at the ac outlet, by checking the circuit breaker.

Temperature appears too warm

• Frequent door openings.

• Allow time for recently added beverages to reach proper

temperature.

• Check gaskets for proper seal.

• Adjust temperature control to cooler setting.

Temperature is too cold

• If temperature control setting is too cold, adjust to a warmer setting

and allow several hours for temperature to adjust.

Beverage Center runs too frequently

• This may be normal to maintain constant temperature during

high temperature and humid days.

• Doors may have been opened frequently or for an extended

period of time.

• Check gasket for proper seal.

• Check to see if doors are completely closed.

Moisture build up on interior or exterior

of the beverage center:

• This is normal during high humidity periods.

• Prolonged or frequent door openings.

• Check door gaskets for proper seal.

Beverage Center door does not shut properly:

• Level the beverage center.

• Re-align beverage center door.

• Check for blockages.

TroubleShooting

English

16

Limited Warranty

What is covered and for how

long?

This warranty covers all defects in

workmanship or materials for a period

of:

12 months labor (carry in only)

12 months parts (carry in only)

5 years sealed system

(carry in only)

The warranty commences on the date

the item was purchased and the original

purchase receipt must be presented to

the authorized service center before

warranty repairs are rendered.

EXCEPTIONS: Commercial or

Rental Use warranty

90 days labor (carry-in only)

90 days parts

No other warranty applies

What is covered.

1. The mechanical and electrical parts,

which serve as a functional, purpose

of this appliance for a period of 12

months. This includes all parts except

finish, and trim.

2. The components of the sealed system

e.g. hermetic compressor, condenser

and evaporator from manufacturing

defects for a period of 5 years from

the date of purchase. Any damages

to such components caused by

mechanical abuse or improper

handling or shipping will not be

covered.

What will be done?

1. We will repair or replace, at our

discretion any mechanical or

electrical part which proves to be

defective in normal usage during the

warranty period so specified.

2. There will be no charge to the

purchaser for parts and labor on any

covered items during the initial 12

month period. Beyond this period

only parts are covered in the

remaining warranty. Labor is not

provided and must be paid by

the customer.

3. Contact your nearest authorized

service center. For the name of the

nearest service center please call

1-877-337-3639

THIS WARRANTY COVERS

APPLIANCES WITHIN THE

CONTINENTAL UNITED STATES,

PUERTO RICO AND CANADA.

IT DOES NOT COVER

THE FOLLOWING:

Damages from improper installation.

Damages in shipping.

Defects other than manufacturing.

Damage from misuse, abuse, accident,

alteration, lack of proper care and

maintenance or incorrect current or

voltage.

Damage from other than household use.

Damage from service by other than an

authorized dealer or service center.

Decorative trims or replaceable

light bulbs.

Transportation and shipping.

Labor (after the initial 12 months).

THIS LIMITED WARRANTY IS GIVEN IN

LIEU OF ALL OTHER WARRANTIES,

EXPRESSED OR, INCLUDING THE

WARRANTIES OF MERCHANTABILITY

AND FITNESS FOR A PARTICULAR

PURPOSE

The remedy provided in this warranty is

exclusive and is granted in lieu of all

other remedies.

This warranty does not cover incidental

or consequential damages, so the above

limitations may not apply to you. Some

States do not allow limitations on how

long an implied warranty lasts, so the

above limitations may not apply to you.

This warranty gives you specific legal

rights, and you may have other rights,

which vary, from state to state.

Haier America

New York, NY 10018

MESURES DE SÉCURITÉ

Lisez attentivement toutes les instructions avant d’utiliser cet appareil. Lors

de son utilisation, suivez toutes les mesures de sécurité élémentaires, y com-

pris les mesures suivantes:

1) N’utiliser cet appareil que conformément à ce manuel d'utilisation et

d'entretien.

2) Avant son utilisation, cet appareil doit être installé conformément aux

instructions d’installation. Voir les instructions relatives au branchement

dans la section sur l’installation.

3) Ne jamais débrancher votre minibar en tirant sur le câble d’alimentation.

Toujours serrer fermement la fiche puis la retirer de la prise en la

maintenant bien droite.

4) Réparer ou remplacer immédiatement tous les câbles électriques usés ou

endommagés. Ne pas utiliser de cordon d’alimentation présentant des

craquelures ou des dommages dus à des frottements sur le câble

lui-même, sur la fiche ou sur le connecteur.

5) Débrancher le minibar avant de le nettoyer et avant toute réparation.

Remarque: si, pour une quelconque raison, vous devez faire réparer cet

appareil, nous vous conseillons vivement de faire appel à un technicien

agréé.

6) Si votre ancien minibar n’est plus utilisé, nous vous recommandons de

retirer les portes et de laisser les étagères en place. Cela réduira les

risques d’accident pour les enfants.

7) Ce minibar ne doit pas être renfermé ni encastré. Il est conçu pour être

utilisé sur pied.

8) Ne jamais utiliser le minibar en présence de gaz explosifs.

VEUILLEZ CONSERVER INSTRUCTIONS

afin de pouvoir les consulter de besoin

1

Français

Merci d’utiliser un produit Haier.

Suivez ce manuel d’instruction simple

d’utilisation pour obtenir le maximum

de votre minibar.

N’oubliez pas d’enregistrer les

numéros de modèle et de série. Ils se

trouvent sur une étiquette à l’arrière

de votre minibar.

Numéro de modèle

Numéro de série

Date d’achat

Veuillez agrafer votre facture avec votre manuel.

Vous en aurez besoin pour bénéficier de la garantie.

DANGER

Cet appareil présente un risque d'enfermement pour les enfants. Avant de

vous débarrasser de votre ancien minibar, veuillez enlever les portes. Laissez

les étagères en place afin que les enfants ne puissent pas grimper à l’in-

térieur.

2

Français

La page charge ...

Haier HC61F Manuel utilisateur

Ce manuel convient également à

Haier HC61F Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents