Philips AVENT SCF293/00 Manuel utilisateur

SCF291

SCF293

ENGLISH 3

ESPAÑOL 20

FRANÇAIS 39

PORTUGUÊS 58

Introduction

Congratulations on your purchase and welcome to Philips! To fully benet from the

support that Philips oers, register your product at www.philips.com/welcome.

General description

A I

J

B

C

D

M

G

H

F

E

K

L

SCF293

SCF291

S UTN PO

Q

R

SCF291

SCF293

130ml

A

Lid with grip

F

Heating element with water reservoir

B

Small basket

G

Base unit

C

Bottom plate for large basket

H

Power cord

D

Large basket with drip tray

I

Tongs

E

Maximum water level indicator

J

Cord storage

SCF293

K

Filter cover

O

Auto mode

L

Filter

P

Dry mode

M

Air outlet

Q

On/o button

N

Sterilize mode

R

Control knob with progress indicator

lights

SCF291

S

On/o indicator light

U

Power o button

T

Power on button

Note: You can nd the type number of your sterilizer on the bottom of the

appliance.

3

English

IMPORTANT

SAFEGUARDS

When using electrical appliances, basic safety precautions should always be followed

including the following:

1 Read all instructions.

2 To protect against electrical shock do not immerse cord, plugs or appliance in

water or other liquid.

3 Close supervision is necessary when any appliance is used by or near children.

4 Always unplug from outlet when not in use and before cleaning. Allow to cool

before putting on or taking o parts.

5 Always unplug the cord of the sterilizer before pouring away water and/or rinsing.

6 Do not operate any appliance with a damaged cord or plug or after the appliance

malfunctions or has been damaged in any manner.

7 The use of accessory attachments not recommended by the appliance

manufacturer may cause injuries.

8 Do not use outdoors.

9 Do not let cord hang over edge of table or counter, or touch hot surfaces.

10 Do not place on or near a hot gas or electric burner, or in a heated oven.

11 Extreme caution must be used when moving an appliance containing hot liquids.

Always let the appliance cool down before moving, cleaning or storing it.

12 Always unplug the appliance when not in use.

13 Do not use appliance for other than intended use.

14 WHEN IN USE, THE STERILIZER CONTAINS BOILING WATER AND STEAM ESCAPES

FROM THE VENT IN THE LID.

15 Ensure the sterilizer is placed on a rm level surface when in use.

16 Never move or open the unit when in use.

17 Always keep out of reach of children.

18 Never place items on top of the sterilizer.

19 To stop the sterilizer during the cycle, unplug at the electrical outlet.

20 Take care when opening as steam can burn.

21 Do not use chemical sterilizing solutions/tablets or bleach in your steam sterilizer

or on products to be sterilized.

22 Do not use abrasive, antibacterial materials or scourers to clean the sterilizer.

23 Do not use softened water in the sterilizer.

24 A short power cord has been provided to prevent the risk of it becoming entangled

in or being tripped over. Extension cords may be used if care is exercised in their

use.

25 If an extension cord is used, its electrical rating must be as great as the rating of

the appliance and it must not be draped over the edge of the table top where it

could be pulled by children or tripped over. The extension cord should be a

grounded type 3 wire cord.

26 Failure to follow de-scaling instructions may cause irreparable damage.

27 There are no serviceable parts inside the sterilizer. Do not attempt to open, service

or repair the sterilizer yourself.

4

English

28 Do not touch hot surfaces. Use handles or knobs.

29 HOUSEHOLD USE ONLY.

30 Check if the voltage that is indicated on the appliance corresponds to the local

voltage before you connect the appliance.

31 Never turn on the sterilizer before lling water into the water reservoir in Sterilize

and Auto mode.

32 Do not sterilize very small parts which can fall through the holes of the containers

33 Using homeopathic additives in water can have negative impact on steam, health

and can damage plastic parts.

SAVE THESE

INSTRUCTIONS

Caution

- Never use any accessories or parts from other manufacturers or Philips which are

not specically recommended. If you use such accessories or parts, your warranty

becomes invalid.

- Use distilled water without any additives.

- Do not put bleach or other chemicals in the appliance.

- Only sterilize baby feeding products that have been approved for sterilization.

- Do not expose the appliance to extreme heat or direct sunlight.

- Environmental conditions can inuence the function of the appliance e.g.

temperature, air pressure, local altitudes (sea level), etc.

5

English

Getting to know the settings

Note: Before you sterilize bottles and other items, clean them rst.

Only place items in the sterilizer which are suitable for sterilizing. Do not sterilize items

that are lled with liquid, e.g. a teether with cooling uid.

Sterilize • Sterilize mode is for sterilizing baby items.

• A sterilizing cycle takes approximately 10 minutes.

• Heating up takes approximately 4 minutes and

sterilizing takes approximately 6 minutes.

• Make sure to pour exactly 130 ml/4.5 oz distilled

water directly into the water reservoir of the base .

/

Auto (SCF293 only)

• Auto mode is for sterilizing and drying baby items in

one go.

• An auto cycle takes approximately 40 minutes.

• When you use the “Auto” mode, the appliance

starts sterilizing rst and then drying will

start automatically. The sterilizing cycle takes

approximately 10 minutes, and the drying cycle

takes approximately 30 minutes.

• Make sure to pour exactly 130 ml/4.5 oz distilled

water directly into the water reservoir of the base .

Dry (SCF293 only)

• Dry mode is for drying baby items.

• A drying cycle takes approximately 30 minutes.

• When you dry baby items, do not add water to the

water reservoir of the base.

6

English

Things to Note

SCF293

• Don’t pour water into the air outlet.

• Don’t immerse the base unit in water.

130ml

4.5oz

Distilled

water

• Use 130 ml/4.5 oz distilled water.

• Clean the items beforehand.

• Disassemble all parts completely and

place them with openings pointing

down.

• Pour out the remaining water from

large basket after each use.

SCF293

• Clean the lter every 4 weeks.

Every

4 weeks

• Descale the sterilizer every 4 weeks.

7

English

Before rst use

When you use the appliance for the rst time, we advise you to let it complete one

sterilization process with empty baskets.

1 Use a clean baby bottle and pour exactly 130 ml/4.5 oz distilled water directly into

the water reservoir of the base.

Tip: Using distilled water can minimize the formation of limescale on heating

element. For more information on limescale, see section “Descaling”.

130ml

130ml/4.5oz

2 Place the large basket on the base.

3 Place the bottom plate in the large basket.

4 Place the small basket on the large basket.

8

English

5 Place the lid on top of the small basket.

6 Put the plug in the wall socket.

7 SCF291: Press the power on button to switch on the

appliance.

SCF293: Turn the on/o button to “Sterilize” mode. Then

press it to switch on the appliance.

Note: If you plug in the appliance after you have pressed

the power on button, the sterilizer starts working

immediately. You can switch it o by pressing the power o

button.

Caution: The base, the baskets and the lid become hot

during or shortly after operation.

SCF291

SCF293

2

1

SCF291

• The on/o indicator light lights up to indicate that the appliance starts sterilizing.

• When the sterilization process is nished, the light goes o and the appliance

switches o automatically.

SCF293

• All of the progress indicator lights ash to show the appliance is sterilizing.

• When the sterilization process is nished, the lights go o and the appliance

switches o automatically.

• You can turn the on/o button to “Dry” mode to dry the appliance. It takes

approximately 30 minutes to complete the drying cycle.

8 After the appliance has cooled down completely, remove the lid, the small basket,

the bottom plate, the large basket and wipe them dry.

Note: When you remove the large basket from the base, be aware of the remaining

water on the base drip tray.

9 Let the appliance cool down completely for approximately 10 minutes before you

use it again.

Note: The appliance does not work for 10 minutes after a sterilizing cycle. It needs

to cool down rst.

9

English

Preparing for use

Preparing for sterilizing

Before you put the items to be sterilized in the sterilizer, clean them thoroughly in the

dishwasher or clean them by hand with hot water and liquid dishwashing detergent.

Assembling the sterilizer

There are several ways to assemble the sterilizer.

1 With only the small basket on the base to sterilize small

items such as soothers.

2 With only the large basket on the base to sterilize medium-

sized items such as breast pump parts, toddler plates or

toddler cutlery.

3 With the large basket and the small basket on the base

to sterilize up to six 330ml/ 11oz bottles. Place the bottles

upside down in the large basket and place the bottle dome

caps, screw rings and nipples in the small basket.

Note: When you ll the small basket, put screw rings on the

bottom, place the nipples and the bottle caps loosely on

top of the screw rings.

Note: Make sure all parts that need to be sterilized are

completely disassembled and place them in the basket with

their openings pointing down to prevent them from lling

up with water.

10

English

Using the appliance

Sterilizing (SCF291 and SCF293)

1 Pour water directly into the water reservoir of the base (see section “Before rst

use”).

2 Assemble the sterilizer (see section “Assembling the sterilizer”) and place the items

to be sterilized in it.

3 Place the lid on top of the small or large basket.

4 Put the plug in the wall socket.

5 SCF291: Press the power on button to switch on the

appliance.

SCF293: Turn the on/o button to “Sterilize” mode. Then

press it to switch on the appliance.

Caution: The base, the baskets and the lid become hot

during or shortly after operation.

Note: You can switch the appliance o by pressing the

power o button.

SCF291

SCF293

2

1

SCF291

• The on/o indicator light lights up to indicate that the appliance starts sterilizing.

• When the sterilization process is nished, the light goes o and the appliance

switches o automatically.

SCF293

• All of the progress indicator lights ash to show the appliance is sterilizing.

• When the sterilization process is nished, the lights go o and the appliance

switches o automatically.

6 Remove the lid.

Wait until the appliance has cooled down before you remove the lid.

Be careful. Hot steam may come out of the sterilizer.

11

English

7 Remove the bottles and other items from the basket. Use the tongs to remove the

smaller items.

Be careful. The sterilized items may still be hot.

Note: Make sure you wash your hands thoroughly before you touch the sterilized

items.

8 Unplug the appliance and wait until the appliance has cooled down completely.

9 Remove the small basket and large basket.

Note: When you remove the large basket, be aware of the remaining water on the

base drip tray.

Note: The drip tray is designed to catch milk or food residue and prevent it from

going into the water reservoir of the base. This is to optimize the sterilizing

performance and make the heating element easy to clean.

10 Detach the bottom plate from the large basket. Pour out any remaining water from

the large basket drip tray and clean it (see section “Cleaning”).

11 Pour out any remaining water from the water reservoir and wipe it dry.

Note: The appliance does not work for 10 minutes after a sterilizing cycle. It needs

to cool down rst.

Auto – Sterilizing + Drying (SCF293)

1 Pour water directly into the water reservoir of the base (see section “Before rst

use”).

2 Assemble the sterilizer (see section “Assembling the sterilizer”) and place the items

to be sterilized in it.

Note: Make sure all the items are completely disassembled and placed in the

basket with their openings pointing down for eective drying.

Be careful. Hot steam will come out of the sterilizer when drying starts.

3 Place the lid on top of the small or large basket.

4 Put the plug in the wall socket.

12

English

5 Turn the on/o button to “Auto” mode. Then press it to

switch on the appliance.

• The appliance starts sterilizing rst. All of the progress

indicator lights ash to show the appliance is sterilizing.

• After that, drying will start automatically. The progress

indicator lights ash and go o gradually to show the

appliance is drying.

• When the whole process is nished, the lights go o and

the appliance switches o automatically.

Caution: The base, the baskets and the lid become hot

during or shortly after operation.

2

1

6 Remove the lid.

7 Remove the bottles and other items from the basket. Use the tongs to remove the

smaller items.

Be careful. The sterilized items may still be hot.

Note: Make sure you wash your hands thoroughly before you touch the sterilized

items.

Note: The drying result may vary depending on the ambient temperature, ambient

humidity and loading of sterilizer. You can run one more complete drying cycle if

necessary.

8 Unplug the appliance and wait until the appliance has cooled down completely.

9 Remove the small basket and large basket.

Note: When you remove the large basket, be aware of the remaining water on the

base drip tray.

10 Detach the bottom plate from the large basket. Pour out any remaining water from

the large basket drip tray and clean it (see section “Cleaning”)

Drying (SCF293)

1 Assemble the sterilizer (see section “Assembling the sterilizer”) and place the items

to be dried in it.

Note: Make sure all the items are completely disassembled and placed in the

basket with their openings pointing down for eective drying.

Be careful. Hot steam will come out of the sterilizer when drying starts.

2 Place the lid on top of the small or large basket.

13

English

3 Put the plug in the wall socket.

4 Turn the on/o button to “Dry” mode. Then press it to

switch on the appliance.

• Drying will start after about 30 seconds. The appliance

warms up to produce warm air to dry items.

• The progress indicator lights ash and go o gradually to

show the appliance is drying.

• When the drying process is nished, the lights go o and

the appliance switches o automatically.

Caution: The base, the baskets and the lid become hot

during or shortly after operation.

2

1

5 Remove the lid.

6 Remove the bottles and other items from the basket. Use the tongs to remove the

smaller items.

Be careful. The dried items may still be hot.

Note: Make sure you wash your hands thoroughly before you touch the dried

items.

Note: The drying result may vary depending on the ambient temperature, ambient

humidity and loading of sterilizer. You can run one more complete drying cycle if

necessary.

7 Unplug the appliance and wait until the appliance has cooled down completely.

Cleaning

Do not use abrasive or aggressive cleaning agents (e.g. bleach) or a scouring pad to

clean this appliance.

Never immerse the base and the power cord in water or any other liquid.

Note: The sterilizer is not dishwasher-proof. The baskets, the bottom plate and the

lid can be cleaned with hot water and liquid dishwashing detergent.

1 Always unplug the appliance and let it cool down before you clean it.

2 Clean the base with a moist cloth.

14

English

3 Detach the bottom plate from the large basket.

Pour out any remaining water from the large basket drip tray.

Note: Water accumulates on the large basket drip tray after each sterilizing cycle.

Pour out the remaining water from the large basket after each use.

4 Clean the lid, the small basket, the bottom plate and the large basket in hot water

with some liquid dishwashing detergent.

Note: After cleaning, store the sterilizer in a clean and dry place.

Cleaning the lter (SCF293)

1 Detach the lter cover from the base.

2 Take out the lter and clean it under tap water.

15

English

3 Let the lter air dry thoroughly. Put it back on the base and close the lter cover.

Note: Clean the lter at least every 4 weeks to ensure that it continues to lter

eectively.

Descaling

The sterilization process is extremely important to ensure the most hygienic standards

for your baby. Limescale deposits can slow down the sterilization cycle and even

impair its eectiveness.

Limescale is the hard and chalky deposit. Depending on the water type in your area,

limescale can have dierent appearances ranging from snow white looking powder

to brownish stains. The harder the water, the faster scale builds up. It builds up in

appliances as the residue of minerals naturally contained in water, which fail to

evaporate when water is heated. Although it is not harmful as such, it is unsightly, hard

to clean and can impair the operation of appliances or damage their components if

allowed to build up.

Descale the sterilizer at least every 4 weeks to ensure it works eciently.

1 Pour 90ml/3oz of white vinegar (5% acetic acid) and

30ml/1oz of water into the water reservoir.

16

English

2 Place the small basket on the base. Place the lid on top of

the small basket.

3 SCF291: Press the power on button to switch on the

appliance.

SCF293: Turn the on/o button to “Sterilize” mode. Then

press it to switch on the appliance.

Note: Place the small basket on the base to prevent hot

liquid from splashing out.

SCF291

SCF293

2

1

4 Let the appliance operate for 5 minutes, and then switch it o.

SCF291: Press the power o button to switch o the appliance.

SCF293: Press the on/o button to switch o the appliance.

5 min

SCF291

SCF293

5 Empty the water reservoir and rinse it thoroughly. If you still see traces of scale,

remove it by sponge. Rinse again and wipe the base with a damp cloth.

6 Rinse the small basket and lid as well to remove vinegar solution.

Note: You can also use citric acid based descalers.

Note: Do not use other types of descalers.

17

English

Ordering accessories

To buy accessories or spare parts, visit www.philips.com or go to your Philips dealer.

You can also contact the Philips Consumer Care Center in your country (see the

worldwide guarantee leaet for contact details).

Disposal

Your product is designed and manufactured with high quality materials and

components, which can be recycled and reused. For recycling information, please

contact your local waste management facilities or visit www.recycle.philips.com.

Assistance

For assistance visit our website: www.philips.com/Avent or call 1-800-54-Avent

(1-800-542-8368).

Warranty

FULL TWO-YEAR WARRANTY

Philips North America LLC (USA) and Philips Electronics Ltd (CANADA) warrant each

new Philips Avent product, model SCF291, SCF293, against defects in materials or

workmanship for a period of two years from the date of purchase, and agree to repair

or replace any defective product without charge.

IMPORTANT: This warranty does not cover damage resulting from accident, misuse or

abuse, lack of reasonable care, or the axing of any attachment not provided with the

product.

NO RESPONSIBILITY IS ASSUMED FOR ANY SPECIAL, INCIDENTAL OR

CONSEQUENTIAL DAMAGES.

In order to obtain warranty service, simply call 1-800-54 Avent.

Note: This appliance needs to be descaled regularly for optimal performance.

If you do not do this, the appliance may eventually stop working. In this case,

repair is NOT covered by your warranty.

Manufactured for:

Philips Personal Health

A division of Philips North America LLC

P.O. Box 10313, Stamford, CT 06904, USA

In Canada imported by: Philips Electronics Ltd

281 Hillmount Road, Markham, ON L6C 2S3

18

English

Troubleshooting

This chapter summarizes the most common problems you could encounter with

the appliance. If you are unable to resolve the problem with the information below,

contact the Consumer Care Center in your country.

Problem Solution

When should I

descale my sterilizer?

When you use the sterilizer, you may notice that there

are small spots ranging from snow white to brownish

appearing on the heating plate. This is a sign that your

sterilizer should be descaled.

In any case, the sterilizer should be descaled at least every

4 weeks to ensure that it continues to work eectively.

Why is the sterilizing

time so short?

You did not add enough water for sterilizing.

Pour exactly 130 ml/4.5 oz water directly into the water

reservoir of the base.

Why is there still much

water remaining on

the heating plate after

sterilizing?

The heating plate may be blocked by the limescale. The

sterilizer should be descaled at least every 4 weeks.

See section “Descaling”.

Why is there a burning

smell and burnt mark

on the base?

You may not have poured out the remaining water from the

large basket drip tray regularly. Water accumulates on the

large basket drip tray after each sterilizing cycle. Pour out

any remaining water from the large basket after each use.

1 Detach the bottom plate from the large basket. Pour out

any remaining water from the large basket drip tray.

2 Clean the bottom plate and the large basket in hot water

with liquid dishwashing detergent.

The items may not have been cleaned thoroughly before

sterilizing.

Before you put the items to be sterilized in the sterilizer,

clean them thoroughly in the dishwasher or by hand with

hot water and liquid dishwashing detergent.

Why does the

sterilizer stop

working?

The heating plate may be blocked by the limescale. The

sterilizer should be descaled at least every 4 weeks.

See section “Descaling”.

The items are still wet

after drying.

The items may still be wet due to dierent reasons:

• Ambient temperature or humidity

• Loading of sterilizer

• The items stack too closely together

Make sure hot air is able to circulate around the items to

ensure eective drying. You can run one more complete

drying cycle if necessary.

19

English

Introducción

Enhorabuena por su adquisición y bienvenido a Philips Para poder beneciarse

por completo de la asistencia que ofrece Philips, registre el producto en

www.philips.com/welcome.

Descripción general

A I

J

B

C

D

M

G

H

F

E

K

L

SCF293

SCF291

S UTN PO

Q

R

SCF291

SCF293

130ml

A

Tapa con asa

F

Resistencia con depósito de agua

B

Cesta pequeña

G

Unidad base

C

Placa inferior para la cesta grande

H

Cable de alimentación

D

Cesta grande con bandeja de goteo

I

Pinzas

E

Indicador de nivel máximo de agua

J

Recogecable

SCF293

K

Cubierta del ltro

O

Modo automático

L

Filtro

P

Modo de secado

M

Salida de aire

Q

Botón de encendido

N

Modo de esterilización

R

Rueda de control con pilotos

indicadores de progreso

SCF291

S

Piloto indicador de encendido y

apagado

U

Botón de apagado

T

Botón de encendido

Nota: Puede encontrar el número de modelo del esterilizador en la parte inferior

del aparato.

20

Español

La page charge ...

Philips AVENT SCF293/00 Manuel utilisateur

Ce manuel convient également à

Philips AVENT SCF293/00 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents