1
Thank you, and congratulations on your choice of the SRX-02
“Concert Piano” Wave Expansion Board.
This expansion board features stereo sampled sounds of a
concert grand piano, from the most subtle pianissimo sounds
to the most powerful fortissimos.
The stereo waveforms are recorded using two mic’ing
techniques: ON Mic, for well-defined presence; and OFF Mic,
which provides ambient sound. Each is adjustable over four
volume levels, p (piano), mp (mezzopiano), f (forte), and ff
fortissimo).
The expansion board includes Patches applicable to a wide
variety of musical genres, from the traditional piano sounds
essential for Classical music, to sounds combining string,
pad, and other sounds, Split Tones with the bass in the lower
registers, and more.
• Waveforms: 48
• Patches: 50
•
•
Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT
NOTES” (p. 2; p. 4). These sections provide important information concerning the proper operation of the unit.
Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new
unit, this manual should be read in its entirety. The manual should be saved and kept on hand as a convenient
reference.
SRX-02_je 1 ページ ２００５年５月３１日 火曜日 午前１１時４３分
2
USING THE UNIT SAFELY
001
• Before using this unit, make sure to read the
instructions below, and the Owner’s Manual.
..........................................................................................................
002a
• Do not open or perform any internal modifica-
tions on the unit.
..........................................................................................................
003
• Do not attempt to repair the unit, or replace parts
within it (except when this manual provides
specific instructions directing you to do so). Refer
all servicing to your retailer, the nearest Roland
Service Center, or an authorized Roland
distributor, as listed on the “Information” page.
..........................................................................................................
004
• Never use or store the unit in places that are:
• Subject to temperature extremes (e.g., direct
sunlight in an enclosed vehicle, near a heating
duct, on top of heat-generating equipment); or
are
• Damp (e.g., baths, washrooms, on wet floors);
or are
• Humid; or are
• Exposed to rain; or are
• Dusty; or are
• Subject to high levels of vibration.
..........................................................................................................
011
• Do not allow any objects (e.g., flammable material,
coins, pins); or liquids of any kind (water, soft
drinks, etc.) to penetrate the unit.
..........................................................................................................
013
• In households with small children, an adult
should provide supervision until the child is
capable of following all the rules essential for the
safe operation of the unit.
..........................................................................................................
014
• Protect the unit from strong impact.
(Do not drop it!)
..........................................................................................................
106
• Never climb on top of, nor place heavy objects on
the unit.
..........................................................................................................
115b
• Install the circuit board only into the specified unit
(Fantom series/XV series/MX-200/RD series with
SRX slots/MC-909/VR-760/G-70). Remove only
the specified screws during the installation.
..........................................................................................................
Used for instructions intended to alert
the user to the risk of injury or material
damage should the unit be used
improperly.
* Material damage refers to damage or
other adverse effects caused with
respect to the home and all its
furnishings, as well to domestic
animals or pets.
Used for instructions intended to alert
the user to the risk of death or severe
injury should the unit be used
improperly.
The ● symbol alerts the user to things that must be
carried out. The specific thing that must be done is
indicated by the design contained within the circle. In
the case of the symbol at left, it means that the power-
cord plug must be unplugged from the outlet.
The symbol alerts the user to important instructions
or warnings.The specific meaning of the symbol is
determined by the design contained within the
triangle. In the case of the symbol at left, it is used for
general cautions, warnings, or alerts to danger.
The symbol alerts the user to items that must never
be carried out (are forbidden). The specific thing that
must not be done is indicated by the design contained
within the circle. In the case of the symbol at left, it
means that the unit must never be disassembled.
* In the interest of product improvement, the specifications and/or contents of this package are subject to change
without prior notice.
SRX-02_je 2 ページ ２００５年５月３１日 火曜日 午前１１時４３分
3
SRX-02_je 3 ページ ２００５年５月３１日 火曜日 午前１１時４３分
4
IMPORTANT NOTES
When you purchase the SRX-02 expansion board from an
authorized Roland dealer, the included sounds and samples
are licensed, not sold, to you by Roland Corporation, for
commercial use in music production, public performance,
broadcast, etc.
You may use any of the included phrases and/or samples in
a commercial or non-commercial recording without paying
any additional license fees. However, you must strictly
adhere to the following crediting guidelines on any music
recording that utilize material from SRX-02.
Reproduction or duplication of this collection or any of the
sound recording contained in the SRX-02, either as they exist
on this expansion board or by any means of reformatting,
mixing, filtering, re-synthesizing, processing or otherwise
editing for use in another product or for re-sale, is strictly
prohibited without the express written consent of Roland. All
unauthorized giving, trading, lending, renting, re-issue, re-
distribution or re-sale of the sounds included in the SRX-02
are expressly prohibited.
In Plain English: Be creative in your application of the SRX-
02 sounds, and keep this library for your use only. DO NOT
COPY IT.
Roland constantly monitors other Soundware releases to
check for copyright infringements, and will prosecute all
piracy and copyright violations to the fullest extent of the
law.
THIS LIBRARY IS GUARANTEED TO BE 100%
COPYRIGHT CLEAN.
291a
In addition to the items listed under “USING THE UNIT
SAFELY” on page 2, please read and observe the
following:
901
To avoid the risk of damage to internal components that can
be caused by static electricity, please carefully observe the
following whenever you handle the board.
1
* Before you touch the board, always first grasp a metal object
(such as a water pipe), so you are sure that any static
electricity you might have been carrying has been discharged.
2
* When handling the board, grasp it only by its edges. Avoid
touching any of the electronic components or connectors.
5
* Save the bag in which the board was originally shipped, and
put the board back into it whenever you need to store or
transport it.
901 (F)
Veuillez suivre attentivement les instructions suivantes
quand vous manipulez la carte afin d’éviter tout risque
d’endommagement des pièces internes par l’électricité
statique.
1
* Toujours toucher un objet métallique relié à la terre (comme
un tuyau par exemple) avant de manipuler la carte pour vous
décharger de l’électricité statique que vous auriez pu
accumuler.
2
* Lorsque vous manipulez la carte, la tenir par les côtés. Évitez
de toucher aux composants ou aux connecteurs.
5
* Conservez le sachet d’origine dans lequel était la carte lors de
l’envoi et remettez la carte dedans si vous devez la ranger ou la
transporter.
SRX-02_je 4 ページ ２００５年５月３１日 火曜日 午前１１時４３分
5
21 3
Wave Expansion Board (SRX series)
Carte d'extension Wave (serie SRX)
Connector
Connecteur
Board holder
Support à carte
Position them as shown before you install the board.
Avant l’installation, orienter les supports à carte tel qu’indiqué sur le schéma.
LOCK
Installation tool
Outil d'installation
Screwdriver
Tournevis
INSTALLING THE WAVE EXPANSION
BOARD
* Turn off your instrument.
1.
Remove the cover located on the top (or rear) of your
instrument.
2.
Insert the Wave Expansion Board connector into a connector
for an SRX Series slot, while simultaneously inserting the
board holders into the holes in the Wave Expansion Board.
* Do not touch any of the printed circuit pathways or connection
terminals.
* Never use excessive force when installing a circuit board. If it
doesn’t fit properly on the first attempt, remove the board and try
again.
3.
Use the supplied Installation Tool to turn the holders in the
LOCK direction, so the board will be fastened in place.
(To remove the Wave Expansion Board, turn the board holders
in the UNLOCK direction, and lift up the board.)
* When circuit board installation is complete, double-check your
work.
4.
Using the screws removed in Step 1, refasten the cover in its
original position.
5.
Check if the Wave Expansion Board is correctly installed.
* If the “EXP” display cannot be selected (doesn’t appear) in the
Waveform Selection Screen (refer to the owner’s manual of the
instrument you use), remove the Wave Expansion Board and
install it properly.
* Éteindre l'instrument.
1.
Retirer le couvercle situé sur le dessus (ou á l'arrière) de
l'instrument.
2.
Inserer le connecteur de la carte dans un des creneaux pour
la serie SRX tout en enfoncant les supports a carte dans les
trous de celle-ci.
* Ne pas toucher aux circuits imprimes ou aux connecteurs.
* Ne jamais forcer lors de l'installation de la carte de circuits
imprimes. Si la carte s'ajuste mal au premier essai, enlevez la
carte et recommencez l'installation.
3.
Utiliser l'outil d'installation fourni pour tourner les clips de
retenue vers la position de blocage (LOCK) de façon á ce que
la carte soit retenue en place.
(Pour retirer la carte d'expansion Wave, tourner les clips de
retenue de la carte vers la position déblocage (UNLOCK) et
retirer la carte en la soulevant.)
* Quand l'installation de la carte de circuits imprimes est terminee,
reverifiez si tout est bien installe.
4.
Remettre la plaque a sa place et la fixer a l'aide des vis
enlevees a l'etape 1.
5.
S'assurer que la carte d'expansion Wave est installée
correctement.
* S'il est impossible de sélectionner l'affichage “EXP” (il n'apparaît
pas) á l'écran de sélection Waveform (se reporter au guide du
propriétaire de l'instrument utilisé), retirer la carte d'expansion
Wave et la réinstaller correctement.
1.
2.
3.
4.
5.
SRX-02_je 5 ページ ２００５年５月３１日 火曜日 午前１１時４３分
6
When playing patches on the expansion board, we
recommend that you set all the EFFECTS ON/OFF settings
to “ON.” If such settings are set to “OFF,” you may not
obtain the intended sound.
* Note that the Release Time has been set to a fairly long value
for some of the patches. As a result, if your sound generator
has been set so “Patch Remain” is “ON,” the release portion of
a previously sounding patch may continue to be heard even
after switching to a new patch.
* Refer to the owner’s manual for your instrument for specific
instructions on how to play Patches on the expansion board.
* On the MC-909, only the waveforms can be used. The patches
cannot be used.
Patch List
(BANK SELECT MSB:93; LSB: 1)
No. Name Voices Category
1 PremierGrand 8 AC.PIANO
2 Steady Grand 8 AC.PIANO
3 DynamicGrand 8 AC.PIANO
4 Concert Hall 8 AC.PIANO
5 Bright Grand 6 AC.PIANO
6 Classical 8 AC.PIANO
7 SoftPdlGrand 8 AC.PIANO
8 OnMicPremier 8 AC.PIANO
9 OnMic Bright 6 AC.PIANO
10 OnMicSoftPdl 8 AC.PIANO
11 Premier Mono 4 AC.PIANO
12 Bright Mono 3 AC.PIANO
13 SoftPdl Mono 4 AC.PIANO
14 Mellow Piano 4 AC.PIANO
15 Enhanced Pno 7 AC.PIANO
16 Comp.Piano 6 AC.PIANO
17 HonkytonkPno 4 AC.PIANO
18 NewAgeGrand1 8 AC.PIANO
19 NewAgeGrand2 8 AC.PIANO
20 Requiem 6 AC.PIANO
21 Soundscape 7 AC.PIANO
22 Grand w/Str 8 AC.PIANO
23 Concerto 1 8 AC.PIANO
24 Concerto 2 7 AC.PIANO
25 SoftpadGrand 6 AC.PIANO
(BANK SELECT MSB:93; LSB: 1)
No. Name Voices Category
26 Synpad Grand 6 AC.PIANO
27 Vox Grand 1 6 AC.PIANO
28 Vox Grand 2 7 AC.PIANO
29 Oohs Piano 6 AC.PIANO
30 Air Grand 7 AC.PIANO
31 GtrPad Grand 6 SOFT PAD
32 PhasePad Pno 6 SOFT PAD
33 HeavenPadPno 6 SOFT PAD
34 Somber Pad 6 SOFT PAD
35 Wet Chorus 8 AC.PIANO
36 Nylon Grand 5 AC.PIANO
37 FM EP Grand 5 EL.PIANO
38 Bell Grand 6 EL.PIANO
39 Bellvox Pno 6 BELL
40 StackedGrand 7 EL.PIANO
41 Hard Stack 1 6 AC.PIANO
42 Hard Stack 2 6 AC.PIANO
43 PianoBrass 5 AC.PIANO
44 PianoBrs fff 8 AC.PIANO
45 Gig Split 1 7 COMBINATION
46 Gig Split 2 7 COMBINATION
47 Gig Split 3 7 COMBINATION
48 Throb Piano 7 PULSATING
49 Feedback Pno 4 SYNTH FX
50 Eastern 5th 5 BRIGHT PAD
SRX-02_je 6 ページ ２００５年５月３１日 火曜日 午前１１時４３分
7
These are stereo waveforms, offered in left-right pairs.
When you create a Patch using the waveforms stored in the
Expansion Board, observe the following points:
* If you make a Patch with a single voice and then later play it in
a chord, the sound may be distorted with certain settings for
the Effects and TVA. If this happens, adjust the level of the
Effects and TVA.
Waveform List
No. Name
1 Grand1 L p A
2 Grand1 R p A
3 Grand1 L p B
4 Grand1 R p B
5 Grand1 L p C
6 Grand1 R p C
7 Grand2 L p A
8 Grand2 R p A
9 Grand2 L p B
10 Grand2 R p B
11 Grand2 L p C
12 Grand2 R p C
13 Grand1 L mpA
14 Grand1 R mpA
15 Grand1 L mpB
16 Grand1 R mpB
17 Grand1 L mpC
18 Grand1 R mpC
19 Grand2 L mpA
20 Grand2 R mpA
21 Grand2 L mpB
22 Grand2 R mpB
23 Grand2 L mpC
24 Grand2 R mpC
No. Name
25 Grand1 L f A
26 Grand1 R f A
27 Grand1 L f B
28 Grand1 R f B
29 Grand1 L f C
30 Grand1 R f C
31 Grand2 L f A
32 Grand2 R f A
33 Grand2 L f B
34 Grand2 R f B
35 Grand2 L f C
36 Grand2 R f C
37 Grand1 L ffA
38 Grand1 R ffA
39 Grand1 L ffB
40 Grand1 R ffB
41 Grand1 L ffC
42 Grand1 R ffC
43 Grand2 L ffA
44 Grand2 R ffA
45 Grand2 L ffB
46 Grand2 R ffB
47 Grand2 L ffC
48 Grand2 R ffC
SRX-02_je 7 ページ ２００５年５月３１日 火曜日 午前１１時４３分
8
SRX-02 “Concert Piano”
This warranty is valid only in Japan.
40345423 ’05-6-6N
Copyright © 2000 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND
CORPORATION.
©
SRX-02_je 8 ページ ２００５年５月３１日 火曜日 午前１１時４３分
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
dans d''autres langues
- English: Roland SRX-02 Owner's manual
- 日本語: Roland SRX-02 取扱説明書
Documents connexes
-
Roland GW-8 Le manuel du propriétaire
-
-
Roland FA-76 Le manuel du propriétaire
-
Roland FANTOM X8 Le manuel du propriétaire
-
-
-
Roland Keyboard RS-50 Manuel utilisateur
-