Ryobi RY252CS Manuel utilisateur

Marque: Ryobi

Modèle: RY252CS

Catégorie: Coupe-herbe

Taper: Manuel utilisateur

Ce manuel convient également à

Curved Shaft

RY252CS

RY25CSEMC

Straight Shaft

RY253SS

OPERATOR’S MANUAL

MANUEL D’UTILISATION

MANUAL DEL OPERADOR

25CC 2-CYCLE

STRING TRIMMERS

TAILLE-BORDURES À LIGNE

2 TEMPS DE 25 CC

RECORTADORAS DE HILO

DE DOS TIMPOS 25 CC

NOTICE AVIS AVISO

Do not use E15 or E85 fuel in this product. It is a violation of federal law and will damage the unit and

void your warranty. Only use unleaded gasoline containing up to 10% ethanol.

Ne pas utiliser d’essence E15 ou E85 dans ce produit. Une telle utilisation représente une violation de

la loi fédérale et endommagera l’appareil et annulera la garantie. Utiliser seulement de l’essence sans plomb ne contenant

pas plus de 10 % d’éthanol.

No utilice combustibles E15 o E85 con este producto. Esto constituye una violación a la ley federal, dañará la unidad y anulará

la garantía. Use únicamente gasolina sin plomo con un contenido de hasta 10 % de etanol.

WARNING: To reduce the

risk of injury, the user must read and

understand the operator’s manual

before using this product.

TABLE OF CONTENTS

 General Safety Rules ...................... 2-3

 Specific Safety Rules ..........................3

 Symbols ..............................................4

 Features ..............................................5

 Assembly ........................................ 5-6

 Operation ........................................ 7-9

 Maintenance ............................... 10-12

 Troubleshooting ................................13

 Parts Ordering/Service ........ Back Page

AVERTISSEMENT : Pour

réduire les risques de blessures,

l’utilisateur doit lire et veiller à bien

comprendre le manuel d’utilisation

avant d’employer ce produit.

TABLE DES MATIÈRES

 Règles de sécurité générales .......... 2-3

 Règles de sécurité particulières .......... 3

 Symboles ............................................4

 Caractéristiques ..................................5

 Assemblage .................................... 5-6

 Utilisation ........................................ 7-9

 Entretien ...................................... 10-12

 Dépannage .................................. 13-14

 Commande de pièces/

réparation .......................... Páge arrière

ADVERTENCIA: Para reducir

el riesgo de lesiones, el usuario debe

leer y comprender el manual del

operador antes de usar este producto.

ÍNDICE DE CONTENIDO

 Reglas de seguridad generales ...... 2-3

 Reglas de seguridad específicas ........3

Símbolos .............................................4

 Características ....................................5

 Armado ........................................... 5-6

 Funcionamiento .............................. 7-9

 Mantenimiento ............................ 10-12

 Corrección de problemas ........... 13-14

 Pedidos de piezas/

servicio ........................... Pág. posterior

SAVE THIS MANUAL FOR

FUTURE REFERENCE

CONSERVER CE MANUEL

POUR FUTURE RÉFÉRENCE

GUARDE ESTE MANUAL

PARA FUTURAS CONSULTAS

Fig. 1

A - REEL-EASY

™

tap advance string head

(avance de la ligne de coupe à tapant

REEL-EASY

™

, sistema de avance de hilo por

golpe REEL-EASY

™

)

B - Drive shaft housing (tube de l’arbre moteur,

alojamiento del eje de impulsión)

C - Coupler (coupleur, acoplador)

D - Front handle (poignée avant, mango

delantero)

E - Strap hanger (dispositif d’accrochage,

colgador para la correa)

F - Stop switch (interrupteur d’arrêt, interruptor

de parada)

G - Trigger lock-out (verrouillage de gâchette,

seguro del gatillo)

H - Starter grip and rope (poignée du lanceur et

corde, mango del arrancador y cuerda)

I - Primer bulb (poire d’amorçage, bomba de

cebado)

Curved Shaft

RY252CS

RY25CSEMC

Straight Shaft

RY253SS

J - Fuel cap (bouchon de carburant, tapa del

tanque)

K - Rear handle (poignée arrière, mango trasero)

L - Throttle trigger (gâchette d’accélérateur,

gatillo del acelerador)

- Knob (bouton, perilla)

N - Curved shaft grass deflector (déflecteur

d’herbe d’arbre courbe, deflector de pasto del

eje curvo)

O - Straight shaft grass deflector (déflecteur

d’herbe d’arbre droit, deflector de pasto para

eje recto)

P - Muffler (silencieux, silenciador)

Q - Speed Winder™ (Speed Winder™, Speed

Winder™)

See this fold-out section for all the figures

referenced in the operator’s manual.

Voir que cette section d’encart pour toutes les

figures a adressé dans le manuel d’utilisation.

Vea esta sección de la página desplegable para

todas las figuras mencionó en el manual del operador.

iii

Fig. 2

A - Button (bouton, botón)

B - Guide recess (logement guide, hueco guía)

C - Coupler (coupleur, acoplador)

D - Power head shaft (arbre du bloc moteur, eje

del cabezal motor)

E - Knob (bouton, perilla)

F - Positioning hole (trou de positionnement,

orificio de posicionamiento)

G - Trimmer attachment (accessoire taille-

bordures, aditamento para recortar)

A - Bolt (boulon, perno)

B - Front handle (poignée avant, mango

delantero)

C - Wing nut (écrou papillon, tuerca de

mariposa)

Fig. 5

A - Straight shaft grass deflector (déflecteur

d’herbe d’arbre droit, deflector de pasto para

eje recto)

B - Slot (fente, ranura)

C - Tab (languette, orejeta)

D - Wing screw (vis à oreilles, tornillo de

mariposa)

A - Stop switch (interrupteur d’arrêt, interruptor

de parada)

B - Trigger lock-out (verrouillage de gâchette,

seguro del gatillo)

C - Throttle trigger (gâchette d’accélérateur,

gatillo del acelerador)

D - Starter grip and rope (poignée du lanceur et

corde, mango del arrancador y cuerda)

Fig. 6

Fig. 4

A - Bolt (boulon, perno)

B - Bracket (support, placa)

C - Wing nut (écrou à oreilles, tuerca de

mariposa)

D - Curved shaft grass deflector (déflecteur

d’herbe d’arbre courbe, deflector de pasto

del eje curvo)

A - Stop switch (interrupteur d’arrêt, interruptor

de parada)

B - Trigger lock-out (verrouillage de gâchette,

seguro del gatillo)

C - Primer bulb (poire d’amorçage, bomba de

cebado)

D - Throttle trigger (gâchette d’accélérateur,

gatillo del acelerador)

Fig. 7

B C

Fig. 8

A - Choke lever in FULL CHOKE position

[levier de volet de départ en position FULL

CHOKE (complètement ouvert), palanca

del anegador en posición de FULL CHOKE

(anegación máxima)]

B - Choke lever in HALF CHOKE position (levier

de volet de départ en position HALF CHOKE

(demi étranglement), palanca del anegador

en posición de HALF CHOKE (anegación

media)]

C - Choke lever in RUN position [levier de volet

de départ en position RUN (marche), palanca

del anegador en posición de RUN (marcha)]

Fig. 3

A - String head housing (boîtier de tête de

coupe, alojamiento del cabezal de hilo)

B - Depress tabs (appuyer sur les languettes,

presione los orejetas)

PROPER OPERATING POSITION

BONNE POSITION DE TRAVAIL

POSICIÓN CORRECTA PARA EL MANEJO

DE LA HERRAMIENTA

Fig. 9

A - Curved shaft trimmer (taille-bordures à

arbre courbe, recortadora de eje curvo)

B - Dangerous cutting area (zone de coupe

dangereuse, área peligrosa de corte)

C - Direction of rotation (sens de rotation,

sentido de rotación)

D - Best cutting area (zone d’efficacité

maximum, mejor área de corte)

Fig. 10

A - Eyelet (œillet, ojillo)

B - Arrows (flèches, flechas)

C - Pull strings (tirer vers l’extérieur, tira del

hilo)

D - Rotate the bump knob (tourner le capuchon

du mécanisme de coup dans le sens horaire,

gire a la derecha el perilla percusiva)

Fig. 13

A - Straight shaft trimmer (taille-bordures à

arbre droit, recortadora de eje recto)

B - Dangerous cutting area (zone de coupe

dangereuse, área peligrosa de corte)

C - Best cutting area (zone d’efficacité

maximum, mejor área de corte)

D - Direction of rotation (sens de rotation,

sentido de rotación)

Fig. 11

A - Straight shaft trimmer cut-off blade (lame

de sectionnement de ligne du taille-bordures

à arbre droit, cuchilla de corte de hilo de la

recortadora de eje recto)

B - Curved shaft trimmer cut-off blade (lame de

sectionnement de ligne du taille-bordures à

arbre courbe, cuchilla de corte de hilo de la

recortadora de eje recto)

Fig. 12

Fig. 14

A - Speed Winder™ (Speed Winder™, Speed

Winder™)

B - Bump knob (capuchon du mécanisme de

coup, perilla percusiva)

Fig. 15

Fig. 19

A - Latches (loquets, pestillos)

B - Air filter (filtre à air, filtro de aire)

C - Air filter cover (couvercle du filtre à air, tapa

del filtro de aire)

D - Slots (fentes, ranuras)

Fig. 17

A - Idle speed screw (vis de ralenti, tornillo de

marcha lenta)

Fig. 18

A - Latch (loquet, pestillo)

B - Air filter cover (couvercle du filtre à air, tapa

del filtro de aire)

Fig. 16

A - Upper string head housing (boîtier

supérieure de tête de coupe, alojamiento del

cabezal de hilo superior)

B - Tabs (languettes, lengüetas)

C - Lower string head housing (logement

inférieur de tête de coupe, alojamiento del

cabezal de hilo inferior)

D - Spool (bobine, carrete)

E - Bump knob (capuchon du mécanisme de

coup, perilla percusiva)

F - Spool slots (fentes de bobine, ranuras de

carrete)

G - Knob ribs (côte de bouton, costillas de la

perilla)

2 — English

WARNING:

READ AND UNDERSTAND ALL INSTRUCTIONS.

Failure to follow all instructions listed below may result in

electric shock, fire and/or serious personal injury.

READ ALL INSTRUCTIONS

 For safe operation, read and understand all instructions

before using this product. Follow all safety instructions.

Failure to follow all safety instructions listed below, can

result in serious personal injury.

 Do not allow children or untrained individuals to use this

unit.

 Do not start or operate the engine in a confined space,

building, near open windows, or in other unventilated

space where dangerous carbon monoxide fumes can

collect. Carbon monoxide, a colorless, odorless, and

extremely dangerous gas, can cause unconsciousness

or death.

 Clear the work area before each use. Remove all objects

such as rocks, broken glass, nails, wire, or loose string

which can be thrown or become entangled in the cutting

line or blade.

 Always wear eye protection with side shields marked to

comply with ANSI Z87.1 along with hearing protection

when operating this equipment. Failure to do so could

result in objects being thrown into your eyes and other

possible serious injuries.

 Wear heavy, long pants, long sleeves, boots, and gloves.

Do not wear loose fitting clothing, short pants, sandals,

or go barefoot. Do not wear jewelry of any kind.

 Heavy protective clothing may increase operator fatigue,

which could lead to heat stroke. During weather that is

hot and humid, heavy work should be scheduled for early

morning or late afternoon hours when temperatures are

cooler.

 Never operate this unit on the operator’s left side.

 Secure long hair above shoulder level to prevent entangle-

ment in moving parts.

 Keep all bystanders, children, and pets at least

50 ft. away. Bystanders should be encouraged to wear

eye protection. If you are approached, stop the engine

and cutting attachment. In the case of bladed units, there

is the added risk of injury to bystanders from being struck

with the moving blade in the event of a blade thrust or

other unexpected reaction of the saw.

 Do not operate this unit when you are tired, ill, upset, or

under the influence of alcohol, drugs, or medication.

 Do not operate in poor lighting.

 Keep firm footing and balance. Do not overreach.

Overreaching can result in loss of balance or exposure

to hot surfaces.

GENERAL SAFETY RULES

 Do not use on a ladder or unstable support. Stable foot-

ing on a solid surface enables better control of the unit

in unexpected situations. 

 Keep all parts of your body away from any moving part.

 To avoid hot surfaces, never operate the unit with the

bottom of the engine above waist level.

 Do not touch area around the muffler or cylinder of the

unit, these parts get hot from operation. Contact with hot

surfaces could result in possible serious personal injury.

 Always stop the engine and remove the spark plug wire

before making any adjustments or repairs except for

carburetor adjustments.

 Inspect the unit before each use for loose fasteners, fuel

leaks, etc. Replace any damaged parts before use.

 Never use blades, flailing devices, wire, or rope on trim-

mer attachment. Never use flailing devices, wire, or rope

on any attachment.

 The cutting attachment should never rotate at idle during

normal use. The cutting attachment may rotate at idle

during carburetor adjustments.

 It has been reported that vibrations from hand-held tools

may contribute to a condition called Raynaud’s Syndrome

in certain individuals. Symptoms may include tingling,

numbness, and blanching of the fingers, usually apparent

upon exposure to cold. Hereditary factors, exposure to

cold and dampness, diet, smoking, and work practices

are all thought to contribute to the development of these

symptoms. It is presently unknown what, if any, vibrations

or extent of exposure may contribute to the condition.

There are measures that can be taken by the operator to

possibly reduce the effects of vibration:

a) Keep your body warm in cold weather. When operating

the unit wear gloves to keep hands and wrists warm.

It is reported that cold weather is a major factor con-

tributing to Raynaud’s Syndrome.

b) After each period of operation, exercise to increase

blood circulation.

c) Take frequent work breaks. Limit the amount of

exposure per day.

d) Keep the tool well maintained, fasteners tightened,

and worn parts replaced.

If you experience any of the symptoms of this condition,

immediately discontinue use and see your physician about

these symptoms.

 Mix and store fuel in a container approved for gasoline.

 Mix fuel outdoors where there are no sparks or flames.

Wipe up any fuel spillage. Move 30 ft. away from refueling

site before starting engine. Slowly remove the fuel cap

after stopping engine. Do not smoke when refueling.

 Stop the engine and allow to cool before refueling or

storing the unit.

3 — English

SPECIFIC SAFETY RULES

 Inspect before use. Replace damaged parts. Make sure

fasteners are in place and secure. Check for fuel leaks.

 Replace string head if cracked, chipped, or damaged

in any way. Be sure the string head or blade is properly

installed and securely fastened. Failure to do so can cause

serious injury.

 Make sure all guards, straps, deflectors, and handles are

properly and securely attached.

 Use only recommended or equivalent replacement line in

the cutting head. Do not use any other cutting attachment.

To install any other type of replacement line or cutting

head to this string trimmer can result in serious personal

injury. Never use, for example, wire or wire-rope, which

can break off and become a dangerous projectile.

 Never operate unit without the grass deflector in place

and in good condition.

 Maintain a firm grip on both handles while trimming. Keep

string head below waist level. Never cut with the string

head located over 30 in. or more above the ground.

 This product is intended for infrequent use by homeowners

and other occasional users for such general applications

as trimming light and heavy vegetation, etc. It is not in-

tended for prolonged use. Prolonged periods of operation

can cause circulatory problems in the user’s hands due

to vibration. For such use, it may be appropriate to use

a product having an anti-vibration feature.

Save these instructions. Refer to them frequently and use

them to instruct others who may use this tool. If you loan

someone this tool, loan them these instructions also.

 Allow the engine to cool; empty the fuel tank and secure

the unit from moving before transporting in a vehicle.

 Wear your protective equipment and observe all safety

instructions. For units equipped with a clutch, be sure

the cutting attachment stops turning when the engine

idles. When the unit is turned off make sure the cutting

attachment has stopped before the unit is set down.

GENERAL SAFETY RULES

 We recommend taking your equipment to a qualified

service center for repair, as service performed by in-

experienced or unqualified persons may damage the

equipment, create unsafe conditions, injury to user and/

or void your warranty.

4 — English

Some of the following symbols may be used on this product. Please study them and learn their meaning for safe

operation of this product.

SYMBOL NAME EXPLANATION

Safety Alert Indicates a potential personal injury hazard.

Read Operator’s Manual

To reduce the risk of injury, user must read and under-

stand operator’s manual before using this product.

Eye and Hearing Protection

Always wear eye protection with side shields marked to

comply with ANSI Z87.1 along with hearing protection

when operating this equipment.

Wear Gloves

Wear non-slip, heavy-duty protective gloves when

handling this equipment.

Wear Safety Footwear

Wear non-slip safety footwear when using this

equipment.

Keep Bystanders Away Keep all bystanders at least 50 ft. away.

Ricochet

Thrown objects can ricochet and result in personal injury

or property damage.

No Blade

Do not install or use any type of blade on a product dis-

playing this symbol.

Hot Surface

To reduce the risk of injury or damage, avoid contact

with any hot surface.

Gasoline and Lubricant

Use unleaded gasoline intended for motor vehicle use

with an octane rating of 87 [(R + M) / 2] or higher. This

product is powered by a 2-cycle engine and requires

pre-mixing gasoline and 2-cycle lubricant.

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL SIGNAL MEANING

DANGER:

Indicates a hazardous situation, which, if not avoided, will result in death or

serious injury.

WARNING:

Indicates a hazardous situation, which, if not avoided, could result in death or

serious injury.

CAUTION:

Indicates a hazardous situation, that, if not avoided, may result in minor or

moderate injury.

NOTICE:

(Without Safety Alert Symbol) Indicates information considered important, but

not related to a potential injury (e.g. messages relating to property damage).

SYMBOLS

5 — English

UNPACKING

This product requires assembly.

 Carefully remove the items from the box. Make sure that

all items listed in the packing list are included.

WARNING:

Do not use this product if any parts on the packing list

are already assembled to your product when you unpack

it. Parts on this list are not assembled to the product by

the manufacturer and require customer installation. Use

of a product that may have been improperly assembled

could result in serious personal injury.

 Inspect the unit carefully to make sure no damage oc-

curred during shipping.

 Do not discard the packing material until you have carefully

inspected and satisfactorily operated the product.

 If any parts are damaged or missing, please call

1-800-860-4050 for assistance.

FEATURES

PRODUCT SPECIFICATIONS

Line cutting width

Curved Shaft ............................................................................................................................................................17 in.

Straight Shaft ...........................................................................................................................................................18 in.

Engine displacement ......................................................................................................................................................25cc

Line diameter .............................................................................................................................................................0.095 in.

KNOW YOUR PRODUCT

See Figure 1.

The safe use of this product requires an understanding of

the information on the tool and in this operator’s manual as

well as a knowledge of the project you are attempting. Before

use of this product, familiarize yourself with all operating

features and safety rules.

ERGONOMIC DESIGN

The design of the trimmer provides for easy handling. It is

designed for comfort and ease of grasp when operating in

different positions and at different angles.

GRASS DEFLECTOR

The product includes a grass deflector that helps protect

you from flying debris.

REEL-EASY™ TAP ADVANCE SYSTEM

The Reel-Easy Tap Advance System allows easy line ad-

vance during trimmer operation.

TOP-MOUNTED ENGINE

The top-mounted engine improves balance and is located

away from the dust and debris of the cutting area.

ASSEMBLY

PACKING LIST

Curved Shaft

Trimmer Assembly

Front Handle with Hardware

Curved Shaft Grass Deflector

Bottle of 2-Cycle Lubricant

Speed Winder™

Operator’s Manual

Straight Shaft

Trimmer Assembly

Front Handle with Hardware

Straight Shaft Grass Deflector

Bottle of 2-Cycle Lubricant

Speed Winder™

Operator’s Manual

WARNING:

If any parts are damaged or missing do not operate this

product until the parts are replaced. Use of this product

with damaged or missing parts could result in serious

personal injury.

6 — English

ATTACHING THE FRONT HANDLE

See Figure 3.

 Remove wing nut and bolt from the front handle.

 Install the front handle onto the top side of the drive shaft

housing in the area indicated by the label.

 Place the bolt through the front handle.

NOTE: The hex bolt head fits inside the hex recess

molded into one side of the handle.

 Reinstall the wing nut.

 Tighten wing nut securely.

ATTACHING THE GRASS DEFLECTOR

WARNING:

The line cutting blade on the grass deflector is sharp.

Avoid contact with the blade. Failure to avoid contact

can result in serious personal injury.

TO ATTACH THE CURVED SHAFT GRASS

DEFLECTOR

See Figure 4.

 Remove hex screw and wing nut from grass deflector.

 Press the grass deflector onto the bottom of the curved

shaft as shown.

 Insert the hex screw through the grass deflector and the

bracket on the curved shaft.

 Place the wing nut on the hex screw and tighten securely.

TO ATTACH THE STRAIGHT SHAFT GRASS

DEFLECTOR

See Figure 5.

 Remove the wing screw from the grass deflector.

 Insert the tab on the mounting bracket in the slot on the

grass deflector.

 Align the screw hole in the mounting bracket with the

screw hole in the grass deflector.

 Insert the wing screw through the mounting bracket and

into the grass deflector.

 Tighten the screw securely.

ASSEMBLY

WARNING:

Do not attempt to modify this product or create acces-

sories not recommended for use with this product. Any

such alteration or modification is misuse and could result

in a hazardous condition leading to possible serious

personal injury.

WARNING:

To prevent accidental starting that could cause serious

personal injury, always disconnect the engine spark plug

wire from the spark plug when assembling parts.

INSTALLING THE POWER HEAD TO THE

ATTACHMENT

See Figure 2.

WARNING:

Never install, remove, or adjust any attachment while

power head is running. Failure to stop the engine can

cause serious personal injury.

The attachment connects to the power head by means of

a coupler device.

 Stop the engine and disconnect the spark plug wire.

 Loosen the knob on the coupler of the power head shaft.

 Push in the button located on the trimmer attachment.

Align the button with the guide recess on the power head

coupler and slide the two shafts together. Rotate the trim-

mer attachment until the button locks into the positioning

hole.

NOTE: If the button does not release completely in the

positioning hole, the shafts are not locked into place.

Slightly rotate from side to side until the button is locked

into place.

 Tighten the knob securely.

WARNING:

Be certain the knob is fully tightened before operating

equipment; check it periodically for tightness during use

to avoid serious personal injury.

REMOVING THE ATTACHMENT FROM THE

POWER HEAD

 Stop the engine and disconnect the spark plug wire.

 Loosen the knob.

 Push in the button and twist the shafts to remove and

separate ends.

7 — English

FUELING AND REFUELING THE TRIMMER

WARNING:

Gasoline and its vapors are highly flammable and ex-

plosive. To prevent serious personal injury and property

damage, handle it with care. Keep away from ignition

sources and open flames, handle outdoors only, do not

smoke and wipe up spills immediately.

FUEL MIXTURE

This product is powered by a 2-cycle engine and requires

pre-mixing gasoline and 2-cycle lubricant. Pre-mix unleaded

gasoline and 2-cycle engine lubricant in a clean container

approved for gasoline. DO NOT mix quantities larger than

usable in a 30-day period.

Recommended fuel: This engine is certified to operate on

unleaded gasoline intended for automotive use.

NOTE: We recommend you use Ethanol Shield 2-cycle

lubricant or an equivalent high-quality synthetic 2-cycle

lubricant in this product. Mix at 2.6 oz. per gallon (US).

Do not use automotive lubricant or 2-cycle outboard

lubricant.

HIGH QUALITY 2-CYCLE ENGINE LUBRICANT

GASOLINE LUBRICANT

1.0 gal. (US) (3.8 liter) 2.6 oz. (76 ml)

2.5 gal. (US) (9.5 liter) 6.4 oz. (189 ml)

FILLING TANK

 Clean surface around fuel cap to prevent contamination.

 Loosen fuel cap slowly. Rest the cap on a clean surface.

 Carefully pour fuel mixture into the tank. Avoid spillage.

 Prior to replacing the fuel cap, clean and inspect the

gasket.

 Immediately replace fuel cap and hand tighten. Wipe up

any fuel spillage.

NOTE: It is normal for smoke to be emitted from a new

engine after first use.

WARNING:

Always shut off engine before fueling. Never remove fuel

cap or add fuel to a machine with a running or hot engine.

Make sure the unit is sitting on a flat, level surface and

only add fuel outdoors. If the engine is hot, let the unit cool

for at least five minutes before adding fuel. After fueling,

immediately replace fuel cap and tighten securely. Move

at least 30 ft. from refueling site before starting engine. Do

not smoke and stay away from open flames and sparks!

Failure to follow these instructions could result in a fire

and cause serious personal injury.

WARNING:

Do not allow familiarity with this product to make you

careless. Remember that a careless fraction of a second is

sufficient to inflict serious injury.

WARNING:

Always wear eye protection with side shields marked to

comply with ANSI Z87.1, along with hearing protection.

Failure to do so could result in objects being thrown into

your eyes and other possible serious injuries.

WARNING:

Never use blades, flailing devices, wire, or rope on this

product. Do not use any attachments or accessories not

recommended by the manufacturer of this product. The

use of attachments or accessories not recommended

can result in serious personal injury.

NOTICE:

The spark arrestor on this product has not been evalu-

ated by the USDA Forest Service and cannot be used on

U.S. forest lands. In addition, product users must comply

with Federal, State, and local fire prevention regulations.

Check with appropriate authorities. Contact customer

service or a qualified service center for maintenance and

replacement parts.

NOTICE:

Before each use, inspect the entire product for damaged,

missing, or loose parts such as screws, nuts, bolts, caps,

etc. Tighten securely all fasteners and caps and do not

operate this product until all missing or damaged parts are

replaced. Please contact customer service or a qualified

service center for assistance.

ETHANOL-BLENDED FUELS

NOTICE:

Do not use E15 or E85 fuel in this product. It is a viola-

tion of federal law and will damage the unit and void

your warranty. Only use unleaded gasoline containing

up to 10% ethanol.

NOTE: To improve performance when using oxygenated

fuels, we recommend the use of Ethanol Shield 2-cycle

lubricant.

OPERATION

8 — English

WARNING:

Always position the unit on the operator’s right side. The

use of the unit on the operator’s left side will expose the

user to hot surfaces and can result in possible burn injury.

WARNING:

To avoid burns from hot surfaces, never operate unit with

the bottom of the engine above waist level.

Hold the trimmer with your right hand on the rear handle

and your left hand on the front handle. Keep a firm grip with

both hands while in operation. Trimmer should be held at a

comfortable position with the rear handle about hip height.

Always operate trimmer in RUN position. Cut tall grass

from the top down. This will prevent grass from wrapping

around the shaft housing and string head which could cause

damage from overheating. If grass becomes wrapped around

the string head, STOP THE ENGINE, disconnect the spark

plug wire, and remove the grass. Prolonged cutting at partial

throttle will result in lubricant dripping from the muffler.

WARNING:

Always hold the string trimmer away from the body keep-

ing clearance between the body and the product. Any

contact with the housing or string trimmer cutting head

can result in burns and/or other serious personal injury.

CUTTING TIPS

See Figures 9 - 11.

 Avoid hot surfaces by always keeping the tool away from

your body. (Proper operating position shown in figure 9.)

 Keep the trimmer tilted toward the area being cut; this is

the best cutting area.

 The curved shaft trimmer cuts when passing the unit from

right to left. The straight shaft trimmer cuts when passing

the unit from left to right. This will avoid throwing debris at

the operator. Avoid cutting in the dangerous area shown

in illustration.

 Use the tip of line to do the cutting; do not force string

head into uncut grass.

 Wire and picket fences cause extra line wear, even break-

age. Stone and brick walls, curbs, and wood may wear

line rapidly.

 Avoid trees and shrubs. Tree bark, wood moldings, siding,

and fence posts can easily be damaged by the line.

OPERATION

STARTING AND STOPPING

See Figures 6 - 8.

Trimmer should be on a flat, bare surface for starting.

To start a cold engine:

 Lay the product on a flat, bare surface.

 Push the primer bulb approximately ten times.

 Set the choke lever to FULL CHOKE.

 Depress lock-out button and squeeze throttle trigger

fully and pull starter grip and rope sharply until engine

attempts to start (no more than 4x).

 Set the choke lever to HALF CHOKE.

 Pull starter grip and rope until engine runs, no more than

6 pulls.

 Set the choke lever to RUN.

NOTE: In cooler environments, additional pulls of the

starter grip and rope may be required with the choke

lever in the FULL CHOKE position.

To start a warm engine:

 Lay the product on a flat, bare surface.

 Push the primer bulb up to ten times.

 Set the choke lever to RUN.

 Depress lock-out button and squeeze throttle trigger fully,

pull the starter cord.

NOTE: If the product does not start, repeat the previous

steps.

To stop the engine:

 To stop the engine, depress the STOP switch to the stop

position “ ”.

IF ASSISTANCE IS REQUIRED FOR THIS PRODUCT:

Do not return this product to the retail store where it was

purchased. Please call our Customer Service Department

for any issues you may have.

For Help Call: 1-800-860-4050

OPERATING THE TRIMMER

See Figure 9.

WARNING:

Engine housing can become hot during trimmer opera-

tion. Do not rest or place your arm, hand, or any body

part against the engine housing during trimmer operation.

Only hold the trimmer as shown in figure 9 with all body

parts clear of engine housing. Extended contact with

the engine housing can result in burns or other injuries.

9 — English

OPERATION

TO ADVANCE THE CUTTING LINE

(REEL-EASY

™

STRING HEAD)

Line advance is controlled by tapping the string head on

grass while running engine at full throttle.

 Run engine at full throttle.

 Tap the knob on ground to advance line. The line advances

each time the knob is tapped. Do not hold the knob on

the ground.

NOTE: The line trimming cut-off blade on the grass deflector

will cut the line to the correct length.

NOTE: If the line is worn too short you may not be able to

advance the line by tapping it on the ground. If so, stop the

engine and manually advance the line.

To advance the cutting line manually:

 Stop the engine and disconnect the spark plug wire.

 Push the knob in while pulling on line(s) to manually ad-

vance the line.

GRASS DEFLECTOR LINE TRIMMING CUT-

OFF BLADE

See Figure 12.

The trimmer is equipped with a line trimming cut-off blade

on the grass deflector. For best cutting, advance line until it

is trimmed to length by the cut-off blade. Advance the line

whenever you hear the engine running faster than normal,

or when trimming efficiency diminishes. This will maintain

best performance and keep the line long enough to advance

properly.

10 — English

Normal maintenance, replacement or repair of emission con-

trol devices and systems may be performed by any qualified

repair establishment or individual with original or equivalent

parts. Warranty and recall repairs must be performed by a

authorized service center; please contact customer service

for assistance.

WARNING:

Before inspecting, cleaning, or servicing the machine,

shut off engine, wait for all moving parts to stop, and

disconnect spark plug wire and move it away from spark

plug. Failure to follow these instructions can result in

serious personal injury or property damage.

WARNING:

Always wear eye protection with side shields marked to

comply with ANSI Z87.1, along with hearing protection.

Failure to do so could result in objects being thrown into

your eyes and other possible serious injuries.

WARNING:

When servicing, use only recommended or equivalent

replacement parts. Use of any other parts could create

a hazard or cause product damage.

NOTICE:

Periodically inspect the entire product for damaged,

missing, or loose parts such as screws, nuts, bolts, caps,

etc. Tighten securely all fasteners and caps and do not

operate this product until all missing or damaged parts are

replaced. Please contact customer service or a qualified

service center for assistance.

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most

plastics are susceptible to damage from various types of

commercial solvents and may be damaged by their use.

Use clean cloths to remove dirt, dust, lubricant, grease, etc.

WARNING:

Do not at any time let brake fluids, gasoline, petroleum-

based products, penetrating lubricants, etc., come in con-

tact with plastic parts. Chemicals can damage, weaken or

destroy plastic which could result in serious personal

injury.

MAINTENANCE

LINE REPLACEMENT

See Figures 13 - 14.

Use only .095 in. trimmer line. Use original manufacturer’s

replacement line for best performance.

 Stop the engine and disconnect the spark plug wire.

 Rotate the bump knob clockwise as necessary to align the

arrows on the bump knob with the arrows on the string

head housing.

 Cut one piece of trimmer line 18 ft. long. Insert the line

into the eyelet on the string head housing. Push until the

end of the line comes out the other side of the housing.

Pull the line until equal amounts of line appear on both

sides of the housing.

NOTE: Line may jam if more than 18 ft. is loaded.

 Either by hand or using the Speed Winder™, rotate the

bump knob clockwise to wind the line on the spool until

approximately 6 in. of line is showing on each side.

NOTE: For best results, after every five to seven revolu-

tions of the Speed Winder™, pull both line ends taut for

best loading results and to help prevent line from tangling.

 Push the bump knob down while pulling on line(s) to

manually advance the line.

CLEARING LINE JAM AND/OR REPLACING

BUMP KNOB

See Figures 15 - 16.

 Stop the engine and disconnect the spark plug wire.

 Depress the tabs on the side of the string head housing

to remove the lower string head housing.

NOTE: The housing is spring loaded and will self eject

when the tabs are depressed. It is not necessary to remove

the upper string head housing from the drive shaft.

 Push the spool and bump knob through the string head

housing and remove the string from the spool.

 If replacing the bump knob, remove the old knob from

the spool. Align the knob ribs with the spool slots and

place the new bump knob onto the spool. If you are not

replacing the bump knob, skip this step.

 Insert the bump knob and spool assembly through the

opening in the string head housing.

 Align the slots on the lower string head housing with the

tabs on the upper string head housing.

 Push the housing together until the tabs snap into place.

NOTE: Hold the spool by the knob while completing the

installation.

 Install line as described in Line replacement.

11 — English

MAINTENANCE

CLEANING THE EXHAUST PORT, MUFFLER,

AND SPARK ARRESTOR

NOTICE:

The spark arrestor on this product has not been evalu-

ated by the USDA Forest Service and cannot be used on

U.S. forest lands. In addition, product users must comply

with Federal, State, and local fire prevention regulations.

Check with appropriate authorities. Contact customer

service or a qualified service center to purchase a re-

placement spark arrestor.

NOTE: Depending on the type of fuel used, the type and

amount of lubricant used, and/or your operating conditions, the

exhaust port, muffler, and/or spark arrestor screen may be-

come blocked with carbon deposits. If you notice a power

loss with your gas powered tool, you may need to remove

these deposits to restore performance. We highly recom-

mend that only qualified service technicians perform this

service.

The spark arrestor must be cleaned or replaced every 50

hours or yearly to ensure proper performance of your prod-

uct. Spark arrestors may be in different locations depending

on the model purchased. Please contact your nearest service

dealer for the location of the spark arrestor for your model.

IDLE SPEED ADJUSTMENT

See Figure 17.

WARNING:

The cutting head will move when adjusting the idle speed.

Wear all protective clothing and keep all bystanders,

children, and pets at least 50 ft. away. Make adjustments

with the unit supported by hand so that the blade/cutting

head does not contact the ground or any object. Keep

all parts of your body away from the cutting head and

muffler. Failure to follow these instructions could result

in serious personal injury.

If the cutting attachment turns at idle, the idle speed screw

needs adjusting on the engine. Turn the idle speed screw

counterclockwise to reduce the idle RPM and stop the cut-

ting attachment movement. If the cutting attachment still

moves at idle speed, contact a service dealer for adjustment

and discontinue use until the repair is made.

WARNING:

The cutting attachment should never turn at idle. Turn

the idle speed screw counterclockwise to reduce the

idle RPM and stop the cutting attachment, or contact a

service dealer for adjustment and discontinue use until

the repair is made. Serious personal injury could result

from the cutting attachment turning at idle.

CLEANING THE AIR FILTER

See Figures 18 - 19.

For proper performance and long life, keep air filter clean.

 Remove the air filter cover by pushing down on the latches

while gently pulling off the cover.

 Remove the air filter.

 Clean the foam filter element with warm soapy water.

Rinse and let dry.

NOTE: If the foam filter element is damaged, it should be

replaced.

 Apply a light coat of engine oil to the foam filter element,

then squeeze it out.

 Reinstall the air filter.

NOTE: Make sure the filter is seated properly inside the

cover. Installing the filter incorrectly will allow dirt to enter

the engine, causing rapid engine wear.

 Replace the air filter cover by placing the slots on the air

filter cover over the latches on the housing, then push

the cover down until it snaps securely in place.

FUEL CAP, TANK, AND LINES

WARNING:

Check for fuel leaks. A leaking fuel cap, tank, or line is a

fire hazard and must be replaced immediately. If you find

any leaks, correct the problem before using the product.

Failure to do so could result in a fire that could cause

serious personal injury.

The fuel cap contains a non-serviceable filter and a check

valve. A clogged fuel filter will cause poor engine per-

formance. If performance improves when the fuel cap is

loosened, the check valve may be faulty or filter clogged.

Replace the fuel cap if required.

SPARK PLUG REPLACEMENT

The spark plug for this engine may be replaced using a

Torch L7RTC, Champion RCJ6Y or equivalent spark plug.

The spark plug gap should be set at .025 in. Use a recom-

mended or equivalent replacement and replace annually.

NOTICE:

Be careful not to cross-thread the spark plug. Cross-

threading will seriously damage the product.

STORING THE PRODUCT

 Clean all foreign material from the product. Store idle unit

indoors in a dry, well-ventilated area that is inaccessible

to children. Keep away from corrosive agents such as

garden chemicals and de-icing salts.

12 — English

THIS PRODUCT WAS MANUFACTURED WITH A CATALYST MUFFLER

Congratulations! You have made an investment toward protecting the environment. In order to maintain this product’s

original emission level, please refer to the maintenance section below.

MAINTENANCE

MAINTENANCE SCHEDULE

Inspect For Clean Replace Replace

Maintenance Damage Before Every Every 25 Hours Every

Part Each Use 5 Hours or Yearly 50 Hours

* CATALYTIC MUFFLER ASSEMBLY..................................................................................................................X

SPARK SCREEN ...............................................................................................................................................X

* AIR FILTER ASSY

includes:

Filter Screen ........................................................................ X

* CARBURETOR ASSY

includes:

Gaskets ........................................ X

* FUEL TANK ASSY

includes:

Fuel Lines ..................................... X

Fuel Cap ....................................... X

Fuel Filter................................................................................................................... X

* IGNITION ASSY

includes:

Spark Plug ................................................................................................................. X

* NOTICE: THE USE OF EMISSION CONTROL COMPONENTS OTHER THAN THOSE DESIGNED FOR THIS UNIT

IS A VIOLATION OF FEDERAL LAW.

 Abide by all ISO and local regulations for the safe storage

and handling of gasoline.

When storing 1 month or longer:

 Drain all fuel from tank into a container approved for

gasoline. Run engine until it stops.

HIGH ALTITUDE ENGINE OPERATION

Your engine is configured for operation below 2000 feet

altitude at the factory. Your engine must be re-configured

for operation above 2000 feet altitude. Operating the engine

with the wrong engine configuration at a given altitude may

increase its emissions, decrease fuel efficiency, degrade per-

formance and cause irreversible damage. Engines configured

for high altitude operation cannot be operated in standard

altitude conditions. A qualified service center should ensure

that your engine is properly configured for your location.

This product has a Three-year Limited Warranty for personal,

family, or household use (90 days for business or commercial use).

For warranty details, visit www.ryobitools.com

or call (toll free) 1-800-860-4050.

13 — English

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE SOLUTION

Engine will not start No spark

No fuel

Engine is flooded

Clean or replace spark plug. Reset spark plug gap.

Refer to Spark Plug Replacement earlier in this

manual.

Push primer bulb until bulb is full of fuel. If bulb does

not fill, primary fuel delivery system is blocked.

Contact a qualified service dealer. If primer bulb

fills, engine may be flooded, proceed to next item.

Set the CHOKE lever to the FULL CHOKE position.

Squeeze the trigger and pull the starter grip and rope

repeatedly until the engine starts and runs.

NOTE: Depending on the severity of the flooding,

this may require numerous pulls of the rope.

Engine does not reach full

speed and emits excessive

smoke

Incorrect lubricant/fuel mixture

Air filter screen is dirty

Spark arrestor screen is dirty

Spark plug fouled

Use fresh fuel and the correct 2-cycle lubricant

mix. (50:1).

Clean air filter screen. Refer to Cleaning the Air

Filter earlier in this manual.

Contact a qualified service dealer.

Clean or replace spark plug. Reset spark plug gap.

Refer to Spark Plug Replacement earlier in this

manual.

Engine starts, runs, and

accelerates but will not idle

Idle speed screw on carburetor

needs adjustment

Turn idle speed screw clockwise to increase idle

speed. See Figure 17.

Line will not advance Line is welded to itself

Not enough line on spool

Line is worn too short

Line is tangled on spool

Engine speed is too slow

Lubricate line with silicone spray.

Install more line. Refer to the applicable line re-

placement section in this manual.

Pull lines while alternately pressing down on and

releasing spool retainer.

Remove line from spool and rewind. Refer to the

applicable line replacement section in this manual.

Advance line at full throttle.

Spool retainer hard to turn Screw threads are dirty or damaged Clean threads and lubricate with grease — if no

improvement, replace the spool retainer.

Grass wraps around drive

shaft housing and string

head

Cutting tall grass at ground level

Operating trimmer at part throttle

Cut tall grass from the top down to prevent

wrapping.

Operate trimmer at full throttle

If problem persists after trying the above solutions, contact customer service or a qualified service center for assistance.

NOTICE:

As the equipment owner, you are responsible for the performance of the required maintenance listed in the Maintenance

section. It is recommended that you retain all receipts covering maintenance on your equipment. Neglecting or failing to

perform the required maintenance may increase emissions, decrease fuel efficiency, degrade performance, cause irreversible

engine damage and/or void your warranty.

2 — Français

RÈGLES DE SÉCURITÉ GÉNÉRALES

AVERTISSEMENT :

LIRE ET VEILLER À BIEN COMPRENDRE TOUTES

LES INSTRUCTIONS. Le non respect des instructions

ci-dessous peut entraîner un choc électrique, un incendie

et / ou des blessures graves.

LIRE TOUTES LES INSTRUCTIONS

 Pour travailler en toute sécurité, lire et veiller à bien

comprendre toutes les instructions avant d’utiliser ce

produit. Respecter toutes les instructions de sécurité.

Le non respect des instructions de sécurité ci-dessous

peut entraîner des blessures graves.

 Ne pas laisser des enfants ou personnes n’ayant pas reçu

une formation adéquate utiliser cet outil.

 Ne pas démarrer ou faire tourner le moteur dans un

espace confine, de bâtiment, à proximité des fenêtres

ouverts, autre ou des zones sans ventilation où des

vapeurs toxiques de monoxyde de carbone peuvent

s’accumuler. Le monoxyde de carbone, un gaz incolore,

inodore et extrêmement toxique peut causer une perte

de conscience et être mortel.

 Déblayer la zone de travail avant chaque utilisation. La

débarrasser de tous les objets tels que cailloux, verre brisé,

clous, fils métalliques, cordes, etc. risquant d’être projetés

ou de se prendre dans la ligne de coupe ou la lame.

 Toujours porter une protection oculaire avec écrans

latéraux certifiée conforme à la norme ANSI Z87.1 ainsi

qu’un protection auditive lors de l’utilisation de ce produit.

Si cette précaution n’est pas prise, des objets peuvent

être projetés dans les yeux et causer des lésions graves.

 Porter des pantalons longs, manches longues, des

chaussures de travail et des gants épais. Ne pas porter

de vêtements amples, bijoux, shorts, sandales et ne pas

travailler pieds nus. Ne porter aucun bijou.

 Le fait de porter des vêtements de protection lourds

peut augmenter la fatigue de l’utilisateur, ce qui pourrait

entraîner un coup de chaleur. Si le temps est chaud et

humide, effectuer les gros travaux le matin ou en fin

d’après-midi, alors qu’il fait plus frais.

 Ne jamais utiliser cet outil en le tenant du côté gauche.

 Attacher les cheveux longs pour les maintenir au-dessus

des épaules, afin qu’ils ne se prennent pas dans les pièces

en mouvement.

 Garder les badauds, enfants et visiteurs à une distance de

15 m (50 pi). Recommander aux personnes présente de

porter une protection oculaire. Si quelqu’un s’approche

pendant l’utilisation de l’outil, arrêter le moteur et

l’accessoire de coupe. Le risque de blessure est accru

si on utilise un outil à lames. En effet, les personnes se

trouvant à proximité risquent d’être heurtés par une lame

en marche advenant qu’elle ricoche, ou à la suite de toute

autre réaction inattendue de la scie.

 Ne pas utiliser cet outil en état de fatigue, si l’on est

souffrant ou contrarié ou sous l’influence de l’alcool, de

drogues ou de médicaments.

 Ne pas travailler sous un éclairage insuffisant.

 Se tenir bien campé et en équilibre. Ne pas travailler hors

de portée. Le travail hors de portée risque de faire perdre

l’équilibre ou de causer un contact avec les pièces brûlantes.

 Ne pas utiliser l’outil sur une échelle ou un support instable.

Une bonne tenue et un bon équilibre permettent de mieux

contrôler l’unité en cas de situation imprévue

 Garder toutes les parties du corps à l’écart des pièces

en mouvement.

 Pour éviter le contact avec les parties brûlantes, ne jamais

travailler avec le bas du moteur au-dessus du niveau de

la taille.

Ne pas toucher les alentours de l’échappement ou du

cylindre, qui deviennent brûlants pendant l’utilisation.

Contact avec les surfaces chaudes pourrait entraîner des

blessures graves.

 Toujours arrêter le moteur et débrancher le fil de la bougie

avant d’effectuer tout entretien ou réglage, à l’exception

des réglages du carburateur.

 Inspecter l’outil avant chaque utilisation pour s’assurer qu’il

n’y a pas de pièces desserrées, de fuites ce carburant,

etc. Remplacer les pièces endommagées avant utilisation.

 Ne jamais utiliser des lames, de dispositifs coudés, un

fil ou une corde avec ce accessoire taille-bordures. Ne

jamais utiliser des lames, un dispositif fouetteur, un fil ou

une corde sur une accessoire.

 Lors d’une utilisation normale, l’accessoire de coupe ne

doit jamais tourner au ralenti. La rotation au ralenti est

toutefois permise lors du réglage du carburateur.

 Il a été rapporté que, chez certaines personnes, les

vibrations produites par les outils à main motorisés peuvent

contribuer au développement d’une affection appelée

syndrome de Raynaud. Les symptômes peuvent inclure

des picotements, l’insensibilisation et le blanchissement

des doigts et sont habituellement provoqués par

l’exposition au froid. L’hérédité, l’exposition au froid et à

l’humidité, le régime alimentaire, la fumée et les habitudes

de travail sont tous des facteurs considérés comme

contribuant au développement de ces symptômes. Il

n’existe actuellement aucune preuve qu’un certain type de

vibration ou le degré d’exposition contribue réellement au

développement de cette affectation. Certaines mesures,

susceptibles de réduire les effets des vibrations, peuvent

être prises par l’opérateur :

a) Garder le corps au chaud par temps froid. Pendant

l’utilisation, porter des gants afin de tenir les mains et

les poignets au chaud. Il a été établi que le froid est

l’une des principales causes du symptôme de Raynaud.

b) Après chaque période d’utilisation, faire des exercices

pour accroître la circulation.

3 — Français

RÈGLES DE SÉCURITÉ PARTICULIÈRES

 Inspecter l’outil avant chaque utilisation. Remplacer les

pièces endommagées. S’assurer que toutes les pièces

de boulonnerie sont en place et bien serrées. S’assurer

de l’absence de fuites de carburant.

 Si la tête de coupe est fendue, brisée ou endommagée

de quelque façon que ce soit, la remplacer. S’assurer que

la tête de coupe ou la lame est correctement installée et

solidement assujettie. Ne pas prendre cette précaution

peut entraîner des risques de blessures graves.

 S’assurer que tous les dispositifs de protection, sangles,

déflecteurs et poignées sont correctement installés et

solidement assujettis.

 Utiliser exclusivement des lignes de coupe recommandées

ou équivalentes. Ne jamais utiliser des lames, un dispositif

fouetteur, un fil ou une corde. Utiliser le fil identiques

dans la tête de coupe. N’utiliser aucun autre accessoire

de coupe. Le fait d’installer une tête de coupe de toute

autre marque sur cet accessoire pour taille-bordures peut

entraîner de sérieuses blessures.

 Ne jamais utiliser l’appareil si le déflecteur d’herbe n’est

pas en place et en bon état.

 Tenir fermement les deux poignées pendant le travail. Tenir

la tête de coupe au-dessous du niveau de la taille. Ne

jamais tailler avec la tête de coupe à plus de 762 mm (30 po)

du sol.

 Ce produit est conçu pour les personnes qui prévoient

l’utiliser de manière peu fréquente pour des applications

générales par exemple, tailler la végétation faible et

dense etc.; l’outil peut également convenir à d’autres

utilisateurs occasionnels. Elle n’est pas conçue pour

un usage prolongé. Les périodes d’utilisation prolongée

peuvent entraîner des problèmes circulatoires dans les

mains de l’opérateur, causés par les vibrations. Pour ce

type d’application, il peut être bon d’utiliser une scie

équipée d’un dispositif anti-vibrations.

 Conserver ces instructions. Les consulter fréquemment et

les utiliser pour instruire les autres utilisateurs éventuels.

Si cet outil est prêté, il doit être accompagné de ces

instructions.

RÈGLES DE SÉCURITÉ GÉNÉRALES

c) Faire des pauses fréquentes. Limiter la durée

d’exposition quotidienne.

d) Garder l’outil bien entretenu, toutes les pièces de

boulonnerie serrées et remplacer les pièces usées.

En cas d’apparition de l’un ou plusieurs des symptômes

décrits ci-dessus, cesser d’utiliser l’outil et consulter un

médecin.

 Mélanger et conserver le carburant dans un bidon ou

jerrican approuvé pour l’essence.

 Mélanger le carburant à l’extérieur, loin de toute flamme

ou source d’étincelles. Essuyer tout carburant répandu.

S’éloigner de 9 m (30 pi) du point d’approvisionnement

avant de lancer le moteur. Desserrer le bouchon du

réservoir de carburant lentement une fois que le moteur

est arrêté. Ne pas fumer pendant le ravitaillement en

carburant.

 Arrêter le moteur et le laisser refroidir avant de faire le

plein ou de le remiser.

 Pour le transport dans un véhicule, laisser le moteur

refroidir, vider le réservoir de carburant et arrimer l’outil.

 Porter un équipement de protection et respecter

toutes les instructions de sécurité. Si l’outil est équipé

d’un embrayage, s’assurer que l’accessoire de coupe

s’immobilise lorsque le moteur tourne au ralenti. Lorsque

le moteur est arrêté, s’assurer que l’accessoire de coupe

est immobilisé avant de poser l’outil.

 Il est recommandé d’apporter la équipement à un

centre de réparations qualifié pour la faire réparer pour

éviter que des réparations effectuées par une personne

inexpérimentée ou non qualifiée puissent endommager

la équipement, créer des conditions dangereuses, des

blessures à l’utilisateur et annuler la garantie.

4 — Français

Les termes de mise en garde suivants et leur signification ont pour but d’expliquer le degré de risques associé à

l’utilisation de ce produit.

SYMBOLE SIGNAL SIGNIFICATION

DANGER :

Indique une situation dangereuse qui, si elle n’est pas évitée, aura pour

conséquences des blessures graves ou mortelles.

AVERTISSEMENT :

Indique une situation dangereuse qui, si elle n’est pas évitée, pourrait entraîner

des blessures graves ou mortelles.

ATTENTION :

Indique une situation dangereuse qui, si elle n’est pas évitée, pourraît entraîner

des blessures légères ou de gravité modérée.

AVIS :

(Sans symbole d’alerte de sécurité) Indique les informations jugées

importantes sans toutefois représenter un risque de blessure (ex. : messages

concernant les dommages matériels).

Certains des symboles ci-dessous peuvent être utilisés sur le produit. Veiller à les étudier et apprendre leur signification

pour assurer la sécurité d’utilisation.

SYMBOLE NOM EXPLICATION

Symbole d’alerte de sécurité Indique un risque de blessure potentiel.

Lire le manuel d’utilisation

Pour réduire les risques de blessures, l’utilisateur doit

lire et veiller à bien comprendre le manuel d’utilisation

avant d’utiliser ce produit.

Protection oculaire et auditive

Toujours porter une protection oculaire avec écrans

latéraux certifiée conforme à la norme ANSI Z87.1 ainsi

qu’un protection auditive.

Gants

Porter des gants épais antidérapants lors de l’utilisation

de l’outil.

Chaussures de sécurité

Porter des chaussures de travail à semelle antidérapante

lors de l’utilisation de l’outil.

Ne laisser personne s’approcher

Garder les badauds à une distance de 15 m (50 pi)

minimum.

Ricochet

Les objets projetés peuvent ricocher et infliger des

blessures ou causer des dommages matériels.

Ne pas utiliser de lame

Ne jamais utiliser une lame quelconque sur un outil

portant ce symbole.

Surface chaude

Pour éviter les risques de blessures ou de dommages,

éviter tout contact avec les surfaces brûlantes.

Essence et lubrifiant

Utiliser de l’essence sans plomb pour automobiles, avec

un indice d’octane de 87 [(R + M) / 2] ou plus. Ce produit

utilise un moteur deux temps qui nécessite le mélange

d’essence et de lubrifiant 2 temps.

SYMBOLES

La page charge ...

Ryobi RY252CS Manuel utilisateur

Marque: Ryobi

Modèle: RY252CS

Catégorie: Coupe-herbe

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Ryobi RY252CS User manual
español: Ryobi RY252CS Manual de usuario

Ryobi RY252CS Manuel utilisateur

Ce manuel convient également à

Ryobi RY252CS Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents