Rinnai REU-VC2837WD-US-N Mode d'emploi

— Do not store or use gasoline or other flammable vapors and

liquids in the vicinity of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in

your building.

• Immediately call your gas supplier from a neighbor’s phone.

Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire

department.

— Installation and service must be performed by a qualified

installer, service agency or the gas supplier.

Operation and Installation Manual

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

Outdoor Tankless Water Heater

ANS Z21.10.3

●

CSA 4.3

Table of Contents ..................... 2

Consumer Safety Information ... 4

Operating Instructions ............... 5

Maintenance ........................... 11

Error Codes ............................ 12

Installation Instructions ........... 16

Consumer Support .................. 39

French Version ....................... 42

RL75e ................. REU-VB2528WD-US

RL94e ................. REU-VB2735WD-US

R98LSe ............... REU-VA3237W-US

R98LSe-ASME ... REU-VA3237W-ASME

Register your product at www.rinnairegistration.com or

call 1-866-RINNAI1 (746-6241)

FOR OUTDOOR APPLICATIONS ONLY

If the information in these instructions is not

followed exactly, a fire or explosion may

result causing property damage, personal injury or death.

WARNING

The VB series (RL75e and RL94e) are certified for

installation in manufactured (mobile) homes.

2 VB Series Outdoor LS Manual

Specifications ..................................................... 3

Consumer Safety Information

Safety Definitions ............................................. 4

Safety Behaviors and Practices ....................... 4

Safety Features ............................................... 4

Description of Operation ................................... 5

Operating Instructions

Features Available on Temperature

Controllers ....................................................... 5

Temperature Controller ................................... 6

How to Set the Temperature ........................... 7

Temperature Controller Settings ................. 7, 8

Temperature Options Without

a Temperature Controller ................................ 8

Setting the Sound Volume (Voice Prompt) ...... 8

Using the Water Smart Bath / Fill Function ..... 9

Overview ..................................................... 9

Setting the Water Volume ........................... 9

Filling the Tub............................................ 10

Setting Controller to Mute .............................. 10

Setting the Clock............................................ 10

Maintenance

Cleaning .................................................... 11

Air Intake and Exhaust .............................. 11

Motors ....................................................... 11

Temperature Controller ............................. 11

Lime / Scale Build-up ................................ 11

Snow Accumulation................................... 11

Visual Inspection of Flame ........................ 11

Error Codes

Error Code Table ...................................... 12,13

Trouble Shooting for Common Issues ........... 14

Accessing Operating Information .................. 14

Water Quality ................................................. 14

Flushing the Heat Exchanger

(Error Code: LC or 00) ................................... 15

Installation Instructions ................................... 16

General Instructions ...................................... 16

Environment ................................................... 17

Clearances from Appliance ........................... 18

Attachment of the Water Heater .................... 18

Error Indication or Air Handler Control Switch ..

(RL75e and RL94e only) ............................... 18

Electrical Connection ..................................... 19

Gas Piping

General Instructions ................................ 19

Pipe Sizing Procedure - Example ........... 20

Water Piping

Isolation Valves and Pressure Relief

Valves (RL75e and RL94e) ..................... 21

General Instructions ................................ 22

Pressure Relief Valve .............................. 22

Freeze Protection .............................. 22, 23

Freeze Protection Piping ............................... 24

Recommended Piping for Basic Installation ..

25

Recommended Piping for

Circulation Systems ....................................... 26

Flue Terminal Clearances

(ANS Z21.10.3, CSA 4.3

) .............................. 27

Additional Clearances .................................... 28

Connecting Multiple Water Heaters ............... 29

High Altitude Installations ........................ 29, 30

Temperature Controller Installation

Location ................................................... 31

Configurations ......................................... 31

Cable Lengths and Size .......................... 31

Mounting the Controller ........................... 32

Operating Instructions ................................... 33

Technical Data

Pressure Drop Curve ..................................... 34

Outlet Flow Data ............................................ 34

Space Heating ............................................... 35

Dimensions .................................................... 36

Ladder Diagrams ..................................... 37, 38

Consumer Support

Warranty Information ..................................... 39

Limited Warranty ..................................... 39, 40

State Regulations ............................................. 41

French Version ............................................ 42-59

Table of Contents

This model has been built in accordance with

the requirements of the ASME Boiler and

Pressure Vessel Code and has received the

Certificate of Authorization from the National

Board. The heat exchanger on this unit has

the NB and HLW stamps.

R98LSe-ASME

R

California Proposition 65 lists chemical substances known to the state to cause cancer, birth defects, death,

serious illness or other reproductive harm. This product may contain such substances, be their origin from fuel

combustion (gas, oil) or components of the product itself.

VB Series Outdoor LS Manual 3

Specifications

Model RL75e RL94e R98LSe R98LSe-ASME

Minimum Gas Consumption Btu/h

9,900 (NG)

10,300 (LPG)

19,000

Maximum Gas Consumption Btu/h 180,000 199,000 237,000

Hot water capacity (Min - Max) *

0.4 - 7.5 GPM

(1.5 - 28.5 L/min)

0.4 - 9.4 GPM

(1.5 - 35.5 L/min)

0.6 - 9.8 GPM

(2.3 - 37 L/min)

Hot water capacity (45°F rise)

6.6 GPM

(25.1 L/min)

7.1 GPM

(27.0 L/min)

8.5 GPM

(32 L/min)

Default Temperature Setting (no controller) 120º F (49º C)

Temperature Controller Default Setting 104º F (40º C)

Maximum Temp Setting (commercial **) 160º F (71º C) 185º F (85º C)

Maximum Temp Setting (residential)

see Temperature Ranges for more information

Selectable at 120º F (49º C) or

at 140º F (60º C)

140º F (60º C)

Minimum Temperature Setting 98º F (37º C)

Weight 51 lb (23 kg) 55 lb (25 kg)

Efficiency Energy Factor: 0.82 Thermal Efficiency: 83.0%

Noise level 49 dB (A)

Electrical

Consumption

Normal 44 W 49 W 72 W

Standby 2 W

Anti-frost Protection

104 W 116 W

By-Pass Control Fixed Electronic

Minimum Gas

Supply

Natural Gas 5.0 inch W.C.

Propane 8.0 inch W.C.

Maximum Gas

Supply

Natural Gas 10.5 inch W.C.

Propane 13.5 inch W.C.

Type of Appliance Temperature controlled continuous flow gas hot water system.

Operation With or without temperature controls, mounted in kitchen, bathroom, etc.

Approved Gas Type Natural Gas or Propane - Ensure unit matches gas type supplied at the installation location.

Connections Gas Supply: 3/4" MNPT, Cold Water Inlet: 3/4" MNPT, Hot Water Outlet: 3/4" MNPT

Ignition System Direct Electronic Ignition

Electric Connections Appliance: AC 120 Volts, 60Hz. Temperature Control: DC 12 Volts (Digital)

Water Temperature Control Simulation Feedforward and Feedback.

Water Supply Pressure Minimum Water Pressure: 20 PSI (Recommended 30-80 PSI for maximum performance)

Maximum Water Supply Pressure 150 PSI

Temperature Control Cable Non-Polarized Two Core Cable (Minimum 22 AWG)

Energy Star Qualified Yes Yes No No

Certified for installation in manufactured

(mobile) homes

Yes Yes No No

Energy Factor: 0.82

Rinnai is continually updating and improving products. Therefore, specifications are subject to change without prior notice.

The maximum inlet gas pressure must not exceed the value specified by the manufacturer. The minimum value listed is for

the purpose of input adjustment.

* Minimum flow may vary slightly depending on the temperature setting and the inlet water temperature.

** for commercial and hydronic applications requiring higher temperatures

4 VB Series Outdoor LS Manual

WARNING

Safety Behavior and Practices

• Keep the area around the appliance clear and free

from combustible materials, gasoline, and other

flammable vapors and liquids.

• Do not use this appliance if any part has been under

water. Immediately call a qualified service

technician to inspect the appliance and to replace

any part of the control system and any gas control

which has been under water.

• This appliance is equipped with a three-prong plug

for your protection against shock hazard and should

be plugged directly into a properly grounded three-

prong receptacle. Do not cut or remove the ground

prong from this plug.

• Any alteration to the appliance or its controls can be

dangerous and will void the warranty.

• Always check the water temperature before entering

a shower or bath.

Safety Definitions

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and

others.

Indicates an imminently hazardous situation which, if not avoided, will result in death or

serious injury.

Indicates a potentially hazardous situation which, if not avoided, could result in death or

serious injury.

Indicates a potentially hazardous situation which, if not avoided, could result in minor or

moderate injury. It may also be used to alert against unsafe practices.

DANGER

CAUTION

WARNING

Consumer Safety Information

Safety Features

• Overheat: The appliance will automatically shut

down when the appliance exceeds a predetermined

temperature.

• Flame Failure: The appliance will automatically

shut down if the burner flame is extinguished.

• Power Failure: The appliance will cut off the gas if

it loses electrical power.

• Power Surge Fuse: A glass fuse protects against

overcurrent. If the fuse blows then all indicator

lamps will be off.

• Fusible Link: In case the overheat feature does

not prevent the temperature from rising then the

fusible link will break shutting off the appliance.

VB Series Outdoor LS Manual 5

The Rinnai water heater is one of the most advanced

water heaters available. It provides a continuous

supply of hot water at a preset temperature.

This appliance is a direct vent appliance where air is

brought in from the outside and combustion gases are

exhausted to the outside.

While electricity, water, and gas supplies are

connected, the Rinnai water heater produces hot water

whenever a hot water tap is open.

Ignition is electronic. There is no pilot light consuming

gas while the water heater is not being used. The gas

burner lights automatically when the hot water tap is

opened and goes out when the tap is closed.

Installation of the temperature controller is highly

recommended. The temperature controller can set the

temperature within a specific range and can provide

error codes to diagnose any problems.

The temperature of the outgoing hot water is constantly

monitored. The Rinnai water heater may adjust the

water flow in order to maintain the temperature setting.

The water flow may vary from summer to winter due to

the difference in ground water temperature.

Description of Operation

Features Available on Temperature Controllers

The MC-91 temperature controller is supplied with the appliance. Additional functions are available through the

use of optional controllers.

Operating Instructions

Features

MC-91

MC-100

BC-100

MC-502

Description

Call

Sends a short series of beeps to all controllers in the system. It is

not an intercom.

Clock

12 hour AM/PM clock.

Function

Used on this model to set the clock or sound volume.

In Use Indicator

Indicates that hot water is being supplied (i.e. a hot water tap is

open).

ON/OFF Button

Used to turn the water heater ON or OFF.

Power Save

Allows the temperature controller to be in an energy saving

mode.

Priority Button /

Indicator

Indicates that this controller is setting the temperature . Priority

can be switched to another controller by pressing its Priority

Button when no hot water is running.

Sound Volume

Used to adjust the voice prompt volume.

Temperature Display

Shows the temperature setting.

Thermostat

Increases or decreases the temperature setting.

Water Smart / Bath Fill

Button / Indicator

Used to select the Water Smart / Bath Fill Function to fill a bath

with a predetermined volume of water.

Water Volume

Used to select the water volume for the Water Smart / Bath Fill

Function.

MCC-91

Error Codes

When a fault is detected an error code flashes at the temperature

display on models MC-91, MCC-91, and MC-502; and flashes at

the clock display on models MC-100 and BC-100.

6 VB Series Outdoor LS Manual

Temperature Controller

MC-91-1US & MCC-91-1US

The MC-91 controller is the standard temperature controller that is supplied with the water heater. On indoor

models it is integrated into the front panel. The MCC-91 controller is for commercial and hydronic applications

requiring higher temperatures. When the MCC-91 controller is connected, these higher temperatures are

available on all controller models in the system. Refer to the section on temperature ranges.

Dimensions (inches): 3.5 W x 4.75 H x 0.75 D

Temperature

Display

Priority

Indicator

Priority

Button

ON/OFF

Button

In Use

Indicator

Temperature

Selection

VB Series Outdoor LS Manual 7

How to Set the Temperature

DANGER

Hot water can be dangerous, especially for infants or children, the elderly,

or infirm. There is hot water scald potential if the thermostat is set too high.

Water temperatures over 125º F (51º C) can cause severe burns or

scalding resulting in death.

Hot water can cause first degree burns with exposure for as little as:

3 seconds at 140º F (60º C)

20 seconds at 130º F (54º C)

8 minutes at 120º F (48º C)

Test the temperature of the water before placing a child in the bath or

shower.

Do not leave a child or an infirm person in the bath unsupervised.

Temperature Controller Settings

This water heater will attempt to provide hot water at the temperature setting even when the water flow is varied

or when more than 1 tap is in use. The water heater can deliver water at only one temperature setting at a time.

The available temperatures for a given model are provided below.

Model

RL75e

98 100 102 104 106 108 110 115 120

125

*

130

*

135

*

140

*

150

**

160

**

RL94e

R98LSe

R98LSe-ASME

98 100 102 104 106 108 110 115 120

125

*

130

*

135

*

140

*

150

**

160

**

185

**

Temp in Celsius ºC 37 38 39 40 41 42 43 46 49 52 54 57 60 66 71 85

Temperature Settings Available (ºF)

While any hot water is being provided,

the temperature setting can only be

adjusted between 98º F and 110º F.

NOTICE

Check local codes for the maximum

water temperature setting allowed

when used in nursing homes, schools,

day care centers, and all other public

applications.

NOTICE

If a newly installed unit with a

controller has not been powered for at

least 6 hours then the temperature will

return to the default setting of 104º F

(40º C) if power is interrupted.

NOTICE

There may be a variation between the

temperature displayed on the

temperature controller and the

temperature at the tap due to weather

conditions or the length of pipe to the

water heater.

NOTICE

1. If the water heater is off, press

the ON/OFF button to turn on.

The priority can only be changed

while no hot water is running.

2. Press the “Priority button” on the

temperature controller. The

green Priority light will glow

indicating that this controller is

controlling the temperature and

that the Rinnai water heater is

ready to supply hot water.

3. Press the ▲ or ▼ buttons to

obtain the desired temperature

setting.

All hot water sources are able to

provide water at this temperature

setting until it is changed again at

this or another temperature

controller.

An older controller, MC-45, can be installed with the RL75e, RL94e, R98LSe, and R98LSeASME by moving dip

switch No. 6 in the bank of 6 dip switches to ON. Some of the temperature settings will be slightly different from

the above table.

8 VB Series Outdoor LS Manual

Setting the Sound Volume (Voice Prompt)

BC-100V Press the “Sound Vol.” button to

adjust the voice prompt volume.

The default sound volume is set

to Medium. Each subsequent

press of the button cycles

through the volume levels in the

order below.

MC-100V Press the “Function” button to

adjust the voice prompt

volume. The default sound

volume is set to Medium.

Each subsequent press of the

▲ or ▼ button cycles through

the volume levels in the order

below.

Medium Volume

(default)

High Volume

Off Volume

(beep)

Off Sound

(no beep)

Low Volume

Suggested temperatures are

•Kitchen 120 ºF (49º C)

•Shower 98º - 110º F (37º - 43º C)

•Bath Fill 102º - 110º F (39º - 43º C)

These temperatures are suggestions only.

A temperature lower than 98º F (37º C) can be

obtained at the tap by mixing with cold water.

To change the temperature scale from Celsius to

Fahrenheit or vice versa, press and hold the “On/Off”

button for 5 seconds while the water heater is OFF.

Temperature Options Without a Temperature Controller

The default temperature setting for this appliance installed without a temperature controller is 120º F (49º C). If

desired, the temperature setting can be changed to 140º F (60º C) by adjustment of a dip switch.

In the SW1 bank of 8 dip switches, set dip switch 5 to ON to obtain 140º F water temperature setting. Set dip

switch 5 to OFF (default) to obtain 120º F water temperature setting.

If a temperature controller is installed, then dip switch 5 has no effect on temperature settings.

WARNING

DO NOT adjust the other dip

switches unless specifically

instructed to do so.

The MCC-91 controller is intended for commercial and hydronic

applications only. If an MCC-91 controller is used in a residential

dwelling for a hydronics application, a mixing valve must also be

installed to limit the potable hot water temperature to a safe

temperature. Water temperatures over 125º F (51º C) can cause severe

burns or scalding. Refer to the Danger Alert on water temperatures.

Rinnai shall not, in any event, be liable for damages resulting from such

misuse or misapplication.

** MCC-91 Temperature Controller

These settings require the MCC-91 controller. When the MCC-91

controller is connected, these higher temperatures are available on all

controller models in the system. Use of an MCC-91 controller in a

residential dwelling will reduce the warranty coverage to that of a

commercial warranty application.

* Re-setting the Maximum Temperature (RL75 and RL94 only)

Models RL75 and RL94 have a default maximum temperature of 120º F

(49º C) and an option to increase the maximum temperature to 140 ºF

(60 ºC). Temperature settings from 125-140 ºF (52-60 ºC) are available

by setting dip switch 6 to ON in the SW1 bank of 8 dip switches.

Temperature Controller Settings

Switch No.

F

O

F

8

5

7

6

4

3

ON

1

2

Switch No.

F

O

F

8

5

7

6

4

3

ON

1

2

Maximum Temperature

120º F (49º C) 140 ºF (60 ºC)

VB Series Outdoor LS Manual 9

Using the Water Smart / Bath Fill Function

Overview

This function is exclusive to the BC-100V temperature

controller. The bath fill function allows the consumer

to fill a tub with a preset volume of water at a preset

temperature. This is done by pressing the bath fill

button on the BC-100V controller while no hot water is

flowing and then opening only the hot water tap. The

water heater will stop the hot water flow when the

preset volume has been reached. The hot water tap

should then be closed and the bath fill button pressed.

The temperature settings for the bath fill function are

limited to those in the table below.

Power

Loss

If power is lost during the bath fill

function, the water heater will shut

down but the water will continue to

flow. When power returns, the water

shuts off and Error Code 03 appears

on the controller.

If power is lost after the bath has filled

but before the bath fill function button

is de-selected, then the water will not

flow during the power loss or after the

power is returned. Once power

returns, close the hot water tap and

de-select the bath fill function. No

error code appears.

NOTICE

Multiple

Water

Heaters

The bath fill function will not work

properly if it is connected to multiple

water heaters. The tub will overfill

because the bath fill function is not

able to measure the water volume

when connected to multiple water

heaters.

NOTICE

Bath Fill Temperature Settings Available

ºF 98 100 102 104 106 108 110 115 120

ºC 37 38 39 40 41 42 43 46 49

Anti-scald

Fixtures

Do not use with single handle fixtures

that have anti-scald features built into

them. These fixtures allow a

predetermined amount of cold water

which is not taken into account by the

bath fill function.

NOTICE

Setting the Water Volume

The default volume is set to 25 gallons. The volume

can be set between 10 and 120 gallons.

1. Press the “Priority” button on the

temperature controller. The green

Priority light will glow indicating

that this controller is controlling

the temperature and that the

Rinnai water heater is ready to

supply hot water.

2. Press the “Water Smart Bath Fill”

button to set the water volume

and temperature.

3. Press the “Temp” ▲ or ▼ buttons

to obtain the desired temperature

setting.

To Prevent

Over Filling

Be careful not to overfill the bath. An

average bath volume is 60 gallons.

When filling the bath using this

function for the first time:

•Monitor and remain by the bath while

the water is running.

•Use a low bath fill volume less than

25 gallons

NOTICE

4. Press the “Water Vol.”▲ or ▼

buttons to obtain the desired

water volume in gallons.

5. Press the “Water Smart Bath Fill”

button.

10 VB Series Outdoor LS Manual

Setting Controller to Mute

To eliminate the beeps when keys are pressed or to turn the beeps back on, press and hold both the ▲and ▼

buttons until a beep is heard (approximately 5 seconds).

Models MC-91 and MCC-91

Filling the Tub

Using the Water Smart / Bath Fill Function

Setting the Clock

MC-100V Press the “Function” button twice within 10 seconds to set the clock. Press the ▲ or

▼ button to reach the desired time. The clock on the BC-100V automatically shows

the time which has been set on the MC-100V.

1. Press the “Water Smart / Bath Fill”

button once. The button will

illuminate, and a tone will sound.

2. The voice prompt will announce

“The hot water system is ready.

Open the hot water tap.”

Make sure the water volume is set.

Refer to “Setting the Water

Volume” on the previous page.

Open the hot water tap. The “In

Use” indicator will illuminate on

MC-100V and BC-100V controllers.

The hot water will begin to flow.

3. When the preset volume of water

has been produced then

4. Turn off the bath hot water tap and

push the Bath Fill button. The

water heater will not allow hot

water to flow from any source until

the “Water Smart / Bath Fill” button

is pushed.

The button light will go out.

HOT

COLD

ON!

To Stop the

Bath Fill

Before it

Finishes

To stop the water flow during the Bath

Fill function, press the “Water Smart /

Bath Fill” button. The button will flash

and the voice prompt will announce,

“Hot water is not available. Turn off

all hot water taps and push the Bath

Fill button.” Follow the voice prompt

instructions.

NOTICE

•the water flow will cease

•the “Water Smart / Bath Fill”

button will flash

•a tone will sound

•the voice prompt will announce,

“Bath fill is complete. Turn

off the bath hot water tap and

push the Bath Fill button.”

When

Other Taps

Are Open

During the bath fill function, any hot

water flowing at other locations,

subtracts from the total amount of

water for the bath. For example if the

bath fill function is set for 50 gallons

and 5 gallons of hot water are used at

other locations during the fill period

then the bath will only fill with 45

gallons.

NOTICE

HOT

COLD

ON!

During the operation of the bath fill

function, the MC-91 “In Use” indicator

does not light up.

NOTICE

VB Series Outdoor LS Manual 11

WARNING

Turn off the electrical power supply, the manual gas

valve and the manual water control valve whenever

servicing the unit.

Repairs and maintenance should be performed by a

qualified service technician. The appliance should be

inspected annually by a qualified service technician.

Verify proper operation after servicing.

Cleaning

It is imperative that control compartments, burners,

and circulating air passageways of the appliance be

kept clean.

Clean as follows:

1. Turn off and disconnect electrical power. Allow to

cool.

2. Remove and clean the water inlet filter.

3. Remove the front panel by removing 4 screws.

4. Use pressurized air to remove dust from the main

burner, heat exchanger, and fan blades. Do not

use a wet cloth or spray cleaners on the burner.

Do not use volatile substances such as benzene

and thinners. They may ignite or fade the paint.

5. Use soft dry cloth to wipe cabinet.

Air Intake and Exhaust

The air intake and exhaust should be inspected at

least annually for blockages or damage.

Motors

Motors are permanently lubricated and do not need

periodic lubrication. Keep fan and motor free of dust

and dirt by cleaning annually.

Temperature Controller

Use a soft damp cloth to clean the temperature

controller. Do not use solvents.

Lime / Scale Build-up

If you receive Error Code “LC”, refer to the procedure,

Flushing the Heat Exchanger. Refer to the section on

Water Quality to see if your water needs to be treated

or conditioned. (When checking maintenance code

history, “00” is substituted for “LC”.)

Visual Inspection of Flame

The burner must flame evenly over the entire surface

when operating correctly. The flame must burn with a

clear, blue, stable flame. See the parts breakdown of

the burner for the location of the view ports.

The flame pattern should be as shown in the figures

below.

Snow Accumulation

Keep the area around flue terminal free of snow and

ice. The appliance will not function properly if the

intake air or exhaust is impeded (blocked or partially

blocked) by obstructions.

Maintenance

12 VB Series Outdoor LS Manual

Error Codes

The Rinnai water heater has the ability to check its own operation continuously. If a fault occurs, an error code

will flash on the display of the temperature controller. This assists with diagnosing the fault and may enable you

to overcome a problem without a service call. Please identify the code displayed when inquiring about service.

Code Fault Remedy

02

No burner operation during

freeze protection mode

Service Call

03

Power interruption during

Bath Fill (Water will not flow

when power returns).

Turn off all hot water taps. Press ON/OFF twice.

10

Air Supply or Exhaust

Blockage

Ensure Rinnai approved venting materials are being used.

Check that nothing is blocking the flue inlet or exhaust.

Check all vent components for proper connections.

Ensure vent length is within limits.

Ensure condensation collar was installed correctly.

Verify dip switches are set properly.

Check fan for blockage.

11

No Ignition Check that the gas is turned on at the water heater, gas meter, or cylinder.

Ensure gas type and pressure is correct.

Ensure gas line, meter, and/or regulator is sized properly.

Bleed all air from gas lines.

Verify dip switches are set properly.

Ensure appliance is properly grounded.

Disconnect EZConnect™ or MSA controls to isolate the problem.

Ensure igniter is operational.

Check igniter wiring harness for damage.

Check gas solenoid valves for open or short circuits.

Remove burner cover and ensure all burners are properly seated.

Remove burner plate and inspect burner surface for condensation or debris.

12

Flame Failure Check that the gas is turned on at the water heater and gas meter. Check for

obstructions in the flue outlet.

Ensure gas line, meter, and/or regulator is sized properly.

Ensure gas type and pressure is correct.

Bleed all air from gas lines.

Ensure proper Rinnai venting material was installed.

Ensure condensation collar was installed properly.

Ensure vent length is within limits.

Verify dip switches are set properly.

Ensure appliance is properly grounded.

Disconnect keypad.

Disconnect EZConnect™ or MSA controls to isolate the problem.

Check power supply for loose connections.

Check power supply for proper voltage and voltage drops.

Ensure flame rod wire is connected.

Check flame rod for carbon build-up.

Disconnect and reconnect all wiring harnesses on unit and PC board.

Check for DC shorts at components.

Check gas solenoid valves for open or short circuits.

Remove burner plate and inspect burner surface for condensation or debris.

Check the ground wire for the PC board.

Some of the checks below may need to be done by a qualified service technician. Call a

service technician for any remedy that involves gas or electricity. Call a service

technician if you have any doubt or reservation about performing the remedy yourself.

WARNING

VB Series Outdoor LS Manual 13

Error Codes

Code Fault Remedy

16

Over Temperature

Warning

Check for restrictions in air flow around unit and vent terminal.

Check for low water flow in a circulating system causing short-cycling.

Check for foreign materials in combustion chamber and/or exhaust piping.

Check for clogged heat exchanger.

32

Outgoing Water

Temperature Sensor

Fault

Check sensor wiring for damage.

Measure resistance of sensor.

Clean sensor of scale build-up.

Replace sensor.

33

Heat Exchanger

Outgoing Temperature

Sensor Fault

Check sensor wiring for damage.

Measure resistance of sensor.

Clean sensor of scale build-up.

Replace sensor.

34

Combustion Air

Temperature Sensor

Fault

Check for restrictions in air flow around unit and vent terminal.

Check sensor wiring for damage.

Measure resistance of sensor.

Clean sensor of scale build-up.

Ensure fan blade is tight on motor shaft and is in good condition.

Replace sensor.

52

Modulating Solenoid

Valve Signal Abnormal

Check modulating gas solenoid valve wiring harness for loose or damaged terminals.

Measure resistance of valve coil.

61

Combustion Fan Failure Ensure fan will turn freely.

Check wiring harness to motor for damaged and/or loose connections.

Measure resistance of motor winding.

65

Water Flow Control Fault The water flow control valve has failed to close during the bath fill function. Immediately turn

off the water and discontinue the bath fill function. Contact a state qualified or licensed

contractor to service the appliance.

71

Solenoid Valve Circuit

Fault

Replace the PC Board.

(The RL75, RL94, R98LS have SV0~SV04.)

72

Flame Sensing Device

Fault

Ensure flame rod is touching flame when unit fires.

Check all wiring to flame rod for damage.

Remove flame rod and check for carbon build-up; clean with sand paper.

Check inside burner chamber for any foreign material blocking flame at flame rod.

Measure micro amp output of sensor circuit with flame present.

Replace flame rod.

LC

Scale Build-up in Heat

Exchanger (when

checking maintenance

code history, “00” is

substituted for “LC”)

Flush heat exchanger. Refer to instructions in manual.

Replace heat exchanger.

NOTE: The LC code is the only error code that will allow the unit to keep running. The

display will alternate between the LC code and the temperature setting. The controller will

continue to beep. The LC code will reset if power is turned off and then on.

No

code

Nothing happens when

water flow is activated.

Clean inlet water supply filter.

On new installations ensure hot and cold water lines are not reversed.

Check for bleed over. Isolate unit from building by turning off cold water line to building.

Isolate the circulating system if present. Open your pressure relief valve; if water is

flowing, there is bleed over in your plumbing.

Ensure you have at least the minimum flow rate required to fire unit.

Ensure turbine spins freely.

Measure the resistance of the water flow control sensor.

Check for DC shorts at components.

31

Burner Sensor Error Measure resistance of sensor.

Replace sensor.

73

Burner Sensor Circuit

Error

Check sensor wiring and PC board for damage.

Replace sensor.

14

Thermal Fuse Check gas type of unit and ensure it matches gas type being used.

Check for restrictions in air flow around unit and vent terminal.

Check for low water flow in a circulating system causing short-cycling.

Ensure dip switches are set to the proper position.

Check for foreign materials in combustion chamber and/or exhaust piping.

Check heat exchanger for cracks and/or separations.

Check heat exchanger surface for hot spots which indicate blockage due to scale build-up.

Refer to instructions in manual for flushing heat exchanger.

Measure resistance of safety circuit.

Ensure high fire and low fire manifold pressure is correct.

Check for improper conversion of product.

14 VB Series Outdoor LS Manual

Trouble Shooting for Common Issues

I don’t have any hot water when I open the tap.

Make sure there is gas, water, and electricity to the

Rinnai water heater (power is turned on and the gas is

turned on).

When I was using the hot water, the water got cold.

If you adjusted the flow from the tap to lessen it, you

may have gone below the minimum flow required. The

Rinnai water heater requires a minimum flow rate to

operate. (See the specification page for the flow rate

of your model.)

If you are experiencing issues with higher temperature

settings, then Rinnai recommends reducing the

temperature setting. Selecting a temperature closer to

that which is actually used at the faucet will increase

the amount of hot water being delivered to the faucet,

due to less cold water mixing at the fixture.

White smoke comes out of the exhaust.

During colder weather when the exhaust temperature

is much hotter than the outside air, the exhaust fumes

condense producing water vapor.

When I open a hot tap, I do not immediately get hot

water.

Hot water must travel through your plumbing from the

Rinnai water heater to the faucet. The time period for

hot water to reach your fixture is determined by the

amount of water in the plumbing system between the

water heater and the fixture, water pressure, and the

flow rate of the fixture.

After I turn off the hot water tap, the fan on the

Rinnai water heater continues to run.

The fan is designed to continue running for a short time

after the flow of water stops. This is to ensure constant

water temperatures during rapid starting and stopping,

as well as exhausting any residual gas flue products

from the unit.

Consideration of care for your water heater should

include evaluation of water quality. If the water quality

exceeds the target levels provided in the table, you

may want to treat or condition the water.

* Source: Part 143 National Secondary Drinking Water

Regulations

Maximum Level

Total Hardness Up to 200 mg / L

Aluminum * Up to 0.2 mg / L

Chlorides * Up to 250 mg / L

Copper * Up to 1.0 mg / L

Iron * Up to 0.3 mg / L

Manganese * Up to 0.05 mg / L

pH * 6.5 to 8.5

TDS (Total Dissolved

Solids) *

Up to 500 mg / L

Zinc * Up to 5 mg / L

Water Quality

Accessing Operating Information

To display the most recent error codes press and hold the “On/Off” button for 2 seconds. While holding the “On/

Off” button press the ▲ button. The last 9 error codes will flash one after the other. To exit this mode press the

“On/Off” and ▲ button as before.

To display the water flow through the water heater press and hold the ▲ button for 2 seconds and without

releasing the ▲ button press the “On/Off” button.

To display the outlet water temperature press and hold the ▼ button for 2 seconds and without releasing the ▼

button press the “On/Off” button.

Models MC-91 and MCC-91

VB Series Outdoor LS Manual 15

Water Heater

Pressure Relief Valve

3/4" Ball Valve

3/4" Union

Check Valve

S

Pressure Regulator

Circulating Pump

Solenoid Valve

Boiler Drain Valve

KEY

G

a

s

S

u

p

l

y

V1

V3

V2

V4

H1

H2

H3

Circulating Pump

C

o

l

d

W

a

t

e

r

L

i

n

e

H

o

t

W

a

t

e

r

L

i

n

e

n

-

l

i

n

e

F

i

l

t

e

r

I

Rinnai

Flushing the Heat Exchanger (Error Code: LC or 00)

An “LC” or “00” error code indicates the unit is beginning to lime up and must be flushed. Failure to flush the

appliance will cause damage to the heat exchanger. Damage caused by lime build-up is not covered by the unit’s

warranty. After flushing, reset the LC fault code by turning off the power to the unit and turning the power back

on.

1. Disconnect electrical power to the water heater.

2. Close the shutoff valves on both the hot water and

cold water lines (V3 and V4).

3. Connect pump outlet hose (H1) to the cold water

line at service valve (V2).

4. Connect drain hose (H3) to service valve (V1).

5. Pour 4 gallons of undiluted virgin, food grade,

white vinegar into pail.

6. Place the drain hose (H3) and the hose (H2) to

the pump inlet into the cleaning solution.

7. Open both service valves (V1 and V2) on the hot

water and cold water lines.

8. Operate the pump and allow the cleaning solution

to circulate through the water heater for at least 1

hour at a rate of 4 gallons per minute (15.1 liters

per minute).

9. Turn off the pump.

10. Rinse the cleaning solution from the water heater

as follows:

a. Remove the free end of the drain hose (H3)

from the pail. Place in sink or outside to drain.

b. Close service valve, (V2), and open shutoff

valve, (V4). Do not open shutoff valve, (V3).

c. Allow water to flow through the water heater for

5 minutes.

d. Close shutoff valve (V4). When unit has

finished draining remove the in-line filter at the

cold water inlet and clean out any residue.

Place filter back into unit and open valve (V4).

e. Close service valve, (V1), and open shutoff

valve, (V3).

11. Disconnect all hoses.

12. Restore electrical power to the

water heater.

Cleaning solution is 4 gallons of

undiluted virgin, food grade,

white vinegar.

CLEAN THERMISTORS

Remove and clean thermistors

with a soft cloth or sponge after

removing O-rings.

16 VB Series Outdoor LS Manual

Only properly trained and qualified installers

should install this appliance. The warranty may

be voided due to improper installation or

installation by a non-qualified installer.

Rinnai highly recommends all installers attend a

product knowledge class.

For information on a Rinnai Training Course or

for questions on installation call 1-800-621-

9419.

General Instructions

• This appliance must be installed by a state qualified

or licensed contractor. It is the responsibility of the

person having the water heater installed to ensure

the installing contractor has proper licenses and

permits for installing water heaters in your location.

Rinnai highly recommends that installers attend a

product knowledge class to ensure customer

satisfaction and warranty coverage. Failure to

comply with state and local codes pertaining to

water heater installations may void the warranty.

• This appliance is not to be installed indoors.

• A qualified installer or service technician should

install the appliance, inspect it, and leak test it

before use.

• The installation must conform with local codes or, in

the absence of local codes, with the National Fuel

Gas Code, ANSI Z223.1/NFPA 54, or the Natural

Gas and Propane Installation Code, CSA B149.1. If

installed in a manufactured home, the installation

must conform with the Manufactured Home

Construction and Safety Standard, Title 24 CFR,

Part 3280 and/or CAN/SCA Z240 MH Series, Mobile

Homes.

• The appliance, when installed, must be electrically

grounded in accordance with local codes or, in the

absence of local codes, with the National Electrical

Code, ANSI/NFPA 70, or the Canadian Electrical

Code, CSA C22.1.

• The appliance and its appliance main gas valve

must be disconnected from the gas supply piping

system during any pressure testing of that system at

test pressures in excess of 1/2 psi (3.5 kPa) (13.84

in W.C.).

• The appliance must be isolated from the gas supply

piping system by closing its individual manual

shutoff valve during any pressure testing of the gas

supply piping system at test pressures equal to or

less than 1/2 psi (3.5 kPa) (13.84 in W.C.).

• Follow the installation instructions and those in Care

and Maintenance for adequate combustion and

ventilation air.

• The appliance should be located in an area where

water leakage of the unit or connections will not

result in damage to the area adjacent to the

appliance or to lower floors of the structure. When

such locations cannot be avoided, it is

recommended that a suitable drain pan, adequately

drained, be installed under the appliance. The pan

must not restrict combustion air flow.

• The flow of combustion and ventilation air shall not

be obstructed. Combustion air shall not be supplied

from occupied spaces.

• This appliance is not suitable for use in an

application such as a pool or spa heater that uses

chemically treated water . (This appliance is

suitable for filling large or whirlpool bath tubs with

potable water.)

• If a water heater is installed in a closed water supply

system, such as one having a backflow preventer in

the cold water supply line, means shall be provided

to control thermal expansion. Contact the water

supplier or local plumbing inspector on how to

control thermal expansion.

• Should overheating occur or the gas supply fail to

shut off, turn off the manual gas control valve to the

appliance.

• Keep the air intake location free of chemicals such

as chlorine or bleach that produce fumes. These

fumes can damage components and reduce the life

of your appliance.

• For gas type conversion, contact Rinnai.

WARNING

Do not use substitute materials.

Use only parts certified with the appliance.

Installation Instructions

RL75e ...................... REU-VB2528WD-US

RL94e ...................... REU-VB2735WD-US

R98LSe .................... REU-VA3237W-US

R98LSe-ASME ........ REU-VA3237W-ASME

The VB series (RL75e and RL94e) are certified for

installation in manufactured (mobile) homes.

VB Series Outdoor LS Manual 17

Environment

Air surrounding the water heater, venting, and vent

termination(s) is used for combustion and must be free

of any compounds that cause corrosion of internal

components. These include corrosive compounds

that are found in aerosol sprays, detergents, bleaches,

cleaning solvents, oil based paints/ varnishes, and

refrigerants. The air in beauty shops, dry cleaning

stores, photo processing labs, and storage areas for

pool supplies often contains these compounds.

Therefore it is recommended that outdoor models be

used for these locations where possible.

The water heater, venting, and vent termination(s)

should not be installed in any areas where the air may

contain these corrosive compounds. If it is necessary

for a water heater to be located in areas which may

contain corrosive compounds, the following instruc-

tions are strongly recommended.

IMPORTANT CONSIDERATIONS FOR:

Indoor/Internal Water Heaters

• DO NOT Install in areas where air for combustion

can be contaminated with chemicals.

• Before installation, consider where air has the

ability to travel within the building to the water

heater.

• Where possible, install the water heater in a

sealed closet so that it is protected from the po-

tential of contaminated indoor air.

• Chemicals that are corrosive in nature should not

be stored or used near the water heater.

Outdoor/External Water Heaters and Vent Termina-

tions of Indoor/Internal Water Heaters

• Install the water heater as far away as possible

from exhaust vent hoods.

• Install as far away as possible from air inlet vents.

Corrosive fumes may be released through these

vents when air is not being brought in through

them.

• Chemicals that are corrosive in nature should not

be stored or used near the water heater or vent

termination.

Damage and repair due to corrosive compounds in the

air is not covered by warranty.

18 VB Series Outdoor LS Manual

Clearances from Appliance

1. Identify the installation location and confirm that

the installation will meet all required clearances.

2. Securely attach the water heater to the wall using

any of the holes in the wall installation brackets

which are at the top and bottom of the water

heater. Ensure that the attachment strength is

sufficient to support the weight. Refer to the

weight of the water heater in the Specifications

section.

NOTE: Rinnai water heaters should be installed in an

upright position. Do not install upside down or on it

side.

Attachment of the Water Heater

to Combustibles

to Non-

Combustibles

Top of

Heater

12 inches (305 mm) 2 inches (51 mm)

Back of

Heater

0 (zero) 0 (zero)

Front (Panel)

24 inches (610 mm) * 0 inches (0 mm)

Sides of

Heater

6 inches (152 mm) 1/8 inch (3.2 mm)

Ground/

Bottom

12 inches (305 mm) 2 inches (51 mm)

Front

(Exhaust)

24 inches (610 mm) 24 inches (610 mm)

* The clearance for servicing is 24 inches in front of

the water heater.

wall installation

brackets

Error Indication or Air Handler Control Switch (RL75e and RL94e only)

When using the Rinnai water heater with an Error Indication Switch, dip switch No. 4 in the bank of 8 switches

should be in the off position. This is the default position.

To connect the water heater to the Rinnai Air Handler, the Control Switch is necessary to function as the electrical

connection. When the Control Switch is functioning as the electrical connection between the water heater and air

handler, dip switch No. 4 in the bank of 8 switches should be in the on position.

The Error Indication Switch and the Rinnai Air Handler Control Switch are optional products available from Rinnai.

Installation instructions are included with these products.

to side

to front

to top

to ground/bottom

It is important not to block any of the air inlets which are located on the front and bottom panels of the case.

VB Series Outdoor LS Manual 19

Gas Piping

General Instructions

• A manual gas control valve must be placed in the

gas supply line to the Rinnai water heater. A union

can be used on the connection above the shut off

valve for the future servicing or disconnection of the

unit.

• Check the type of gas and the gas inlet pressure

before connecting the Rinnai water heater. If the

Rinnai water heater is not of the gas type that the

building is supplied with, DO NOT connect the water

heater. Contact the dealer for the proper unit to

match the gas type.

• Check the gas supply pressure immediately

upstream at a location provided by the gas

company. Supplied gas pressure must be within the

limits shown in the Specifications section.

• Before placing the appliance in operation all joints

including the heater must be checked for gas

tightness by means of leak detector solution, soap

and water, or an equivalent nonflammable solution,

as applicable. (Since some leak test solutions,

including soap and water, may cause corrosion or

stress cracking, the piping shall be rinsed with water

after testing, unless it has been determined that the

leak test solution is non-corrosive.)

• Always use approved connectors to connect the unit

to the gas line. Always purge the gas line of any

debris before connection to the water heater.

• The gas supply line shall be gas tight, sized, and so

installed as to provide a supply of gas sufficient to

meet the maximum demand of the heater and all

other gas consuming appliances at the location

without loss of pressure.

• Any compound used on the threaded joint of the gas

piping shall be a type which resists the action of

liquefied petroleum gas (propane / LPG).

• Refer to an approved pipe sizing chart if in doubt

about the size of the gas line.

Electrical Connection

The water heater must be electrically grounded in

accordance with local codes or in the absence of local

codes with the most recent edition of the National

Electrical Code, ANSI/NFPA 70. In Canada, all

electrical wiring should be in accordance with local

codes and the Canadian Electrical Code, CSA C22.1

Part 1. Do not rely on the gas or water piping to

ground the water heater. A screw is provided in the

junction box for the grounding connection.

The water heater requires 120 VAC, 60 Hz power from

a properly grounded circuit.

A disconnect switch must be provided and installed for

the incoming 120 VAC power. It should be a type that

is suitable for outdoor use. Check the National

Electrical Code, ANSI/NFPA 70 and your local codes

for a proper switch type to use in your area.

The wiring diagram is located on the Technical Sheet

attached to the inside of the front cover.

Ground

Connection

Screw

20 VB Series Outdoor LS Manual

Pipe Sizing Procedure - Example

Pipe Size (inches)

3/4 1 1 1/4 1 1/2

10

273 514 1060 1580

20

188 353 726 1090

30

151 284 583 873

40

129 243 499 747

50

114 215 442 662

60

104 195 400 600

70

95 179 368 552

80

89 167 343 514

90

83 157 322 482

100

79 148 304 455

125

70 131 269 403

150

63 119 244 366

175

58 109 224 336

200

54 102 209 313

Length

Pipe Size (inches)

1/2 3/4 1 1 1/4

10

291 608 1150 2350

20

200 418 787 1620

30

160 336 632 1300

40

137 287 541 1110

50

122 255 480 985

60

110 231 434 892

80

101 212 400 821

100

94 197 372 763

125

89 185 349 716

150

84 175 330 677

175

74 155 292 600

200

67 140 265 543

Gas Piping

The gas supply must be capable of handling the entire gas load at the location. Gas line sizing is based on gas

type, the pressure drop in the system, the gas pressure supplied, and gas line type. For gas pipe sizing in the

United States, refer to the National Fuel Gas Code, NFPA 54. For Canadian gas pipe sizing, refer to the Natural

Gas and Propane Installation Code CAN/CSA B149.1. The below information is provided as an example. The

appropriate table from the applicable code must be used.

Pipe Sizing Table - Natural Gas

Pipe Sizing Table - Propane Gas

Inlet Pressure: less than 2 psi (55 inches W.C.)

Pressure Drop: 0.3 inches W.C.

Specific Gravity: 0.60

Inlet Pressure: 11.0 inches W.C.

Pressure Drop: 0.5 inches W.C.

Specific Gravity: 1.50

Schedule 40 Metallic Pipe

cubic feet per hour

Schedule 40 Metallic Pipe

Capacity in Thousands of BTU per Hour

1.For some tables, you will need to determine the cubic feet per hour of gas required by dividing the gas input by

the heating value of the gas (available from the local gas company). The gas input needs to include all gas

products at the location and the maximum BTU usage at full load when all gas products are in use.

Gas Input of all gas products (BTU / HR)

Cubic Feet per Hour (CFH) =

Heating Value of Gas (BTU / FT

3

)

2.Use the table for your gas type and pipe type to find the pipe size required. The pipe size must be able to

provide the required cubic feet per hour of gas or the required BTU/hour.

Example: The gas input of the RL94e is 199,000 BTU/HR using propane. Additional appliances at the location

require 75,000 BTU/hr. Therefore the maximum BTU usage will be 274,000 BTU/hr.

If using propane gas with Schedule 40 metallic pipe, 100 ft in length, then the 1 inch pipe size will be

capable of supplying 372,000 BTU/hr of propane gas..

La page charge ...

Rinnai REU-VC2837WD-US-N Mode d'emploi

Ce manuel convient également à

Rinnai REU-VC2837WD-US-N Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents