Living Earth Crafts Mystia Manuel utilisateur

Marque: Living Earth Crafts

Modèle: Mystia

Catégorie: Masseurs

Taper: Manuel utilisateur

USER MANUAL

1-400-0007 • Rev C • 5/15/17

*all chairs shown with oponal accessories and/or nishes

Club Chair V2

Mystia

5th Avenue

Pedicure Chairs with

Plumbed Tubs

Living Earth Cras®

portion thereof may not be reproduced

in any way, including photocopying or

translation to another language without

the prior written permission from Living

Earth Cras.

Living Earth Cras® is a registered trade-

mark of Earthlite Massage Tables, Inc.

Legal Notice

e information provided in this document is intended

for informational purposes only and is subject to change

without notice. e information provided in this docu-

ment should not be construed as a commitment by

Living Earth Cras®.

Living Earth Cras® assumes no responsibility for the

accuracy or suitability of the information contained in

this document. is document may contain technical

inaccuracies or errors. Living Earth Cras® makes no

expressed or implied warranties of any kind concerning

the information contained in this document, including,

but not limited to, the implied warranties of merchant-

ability and tness for purpose.

Living Earth Cras® shall not be liable for incidental or

consequential damages in connection with or arising out

of the product, performance, or use of this document

and the information and material it describes.

Introduction

Congratulaons on your purchase of the newest innovaon in nail furniture! The Club Chair V2,

Mysa, and 5th Avenue oer fresh alternaves to bulky tradional pedicure thrones. With a

small footprint of a well-appointed manicure chair, the Living Earth Cras pedicure chairs slide

smoothly back to convert into the nest pedicure system available.

The Club Chair V2, Mysa, and 5th Avenue are designed for licensed technicians and are

intended to be used in a professional spa, salon, or similar commercial environment. While no

special training is needed to operate this equipment, for safety reasons it is important that the

instrucons contained in this manual are reviewed in detail before the rst use. This manual

should be read in its enrety by each professional who will be operang the equipment to ensure

the safety of both operator and client. This manual should be saved for future reference.

The Club Chair V2, Mysa, and 5th Avenue should not be used in any other manner than described

in this manual. Please read, understand, and follow all safety warnings, labels, and instrucons.

Misuse, use of unnecessary force, or using the equipment for unintended or unauthorized

procedures can result in injury to operator, client, and/or equipment.

Detailed instrucons for use and maintenance can be found in this user manual. If you have

further quesons, please contact us at (800) 872-0560 for US customers, or (760) 597-2155 for

internaonal customers. We can also be reached via e-mail at info@livingearthcras.com.

Secon 1: Safety Informaon

Safety Symbols & Warnings - English

Safety Symbols & Warnings - French

Secon 2: Product Overview

Chair Models

Foot Spa Overview

Secon 3: Operang Instrucons

Foot Spa Instrucons

Pedicure Chair Instrucons

Relaxor® Heat/Massage

Manicure Trays

Secon 4: Care & Maintenance

Sanijet® Cleaning Instrucons

Care Instrucons

Troubleshoong

Electrical Specicaons

Secon 5: Installaon

Chair Specic Diagrams

Tub Installaon Guidelines

Electrical/Plumbing

2-3

4-5

8-9

12-13

18-20

22-25

Table of Contents

back cover

SECTION 1: SAFETY INFORMATION

Safety Symbols ALERT

Indicates a potentially hazardous

situation which could result in

equipment damage and/or injury.

Familiarize yourself with the following Safety &

Warning symbols. They are designed to prevent

damage and injury to you, your clients, and your

new Living Earth Crafts product.

DANGER

Indicates an imminently hazardous

situation which will result in serious or

fatal injury - used in extreme conditions.

WARNING

Indicates a potentially hazardous

situation which could result in serious

injury.

IMPORTANT SAFETY INSTRUCTIONS

The important safety instructions and warnings in this manual cannot cover all possible problems and condi-

tions that can occur. Use common sense and caution when installing, operating, or maintaining this equipment.

FOR COMMERCIAL USE ONLY - READ ALL INSTRUCTIONS BEFORE USE.

HYDROTHERAPY TUB - INSTALLATION INSTRUCTIONS

WARNING - When using electrical products, basic precautions should always be followed,

including the following:

1. DANGER: RISK OF ELECTRIC SHOCK. Connect only to a circuit protected by a ground-fault circuit-interrupter.

2. Grounding is required. The unit should be installed by a qualied service representative and grounded.

3. A licensed plumber and electrician are required to install your foot bath.

4. Check with a qualied electrician or serviceman if you are in doubt as to whether the product is connected to a

GFCI circuit and/or properly grounded. Do not modify the plug provided with the product - if it will not t the outlet,

have a proper outlet installed by a qualied electrician.

5. Always unplug this furnishing from the electrical outlet before cleaning and/or servicing.

WARNING - RISK OF HYPERTHERMIA AND POSSIBLE DROWNING. Water temperature in excess

of 100.4° (38°C) can be injurious to your health. Check and adjust water temperature before use.

WARNING - The use of alcohol, drugs, or medication can greatly increase the risk of hyperthermia. DO

NOT use drugs or alcohol before using the foot bath.

Hyperthermia ocurs when the internal temperature of the body reaches a level several degrees above the

normal body temperature of 98.6°F. THe symptoms of hyperthermia include an increase in the internal

temperature of the body, dizzines, lethargy, drowsiness, and fainting. The effects of hyperthermia include:

a) Failure to perceive heat,

b) Failure to recognize the need to exit the hydromassage tub,

c) Unawareness of impending hazard,

d) Fetal damage in pregnant women,

e) Physical inability to exit the hydromassage bathtub, and

f) Unconsciousness resulting in the danger of drowning.

To reduce the risk of electric shock, this pedicure chair has a polarized plug (one blade is wider than the

other). This plug will t in a polarized outlet only one way. If the plug does not t fully in the outlet, reverse

the plug. If it still does not t, contact a qualied electrician to install the proper outlet. Do not change the

plug in any way.

SERVICING OF DOUBLE-INSULATED PRODUCT

This pedicure chair is double insulated. In a double-insulated product, two systems of insulation are

provided instead of grounding. No grounding means is provided on a double-insulated product, no should

a means for grounding be added to the product. Servicing a double-insulated product requires extreme

car and knowledge of the system, and should be done only be done by qualied service personnel.

Replacement parts for a double-insulated product must be identical to the parts they replace. A double-

insulated product is marked with the words “DOUBLE INSULATION” or “DOUBLE INSULATED”

READ AND FOLLOW ALL INSTRUCTIONS

SAVE THESE INSTRUCTIONS

SECTION 1: SAFETY INFORMATION

WARNING - RISK OF ACCIDENTAL INJURY OR DROWNING - Children or

handicapped persons should not use foot bath without adult supervision.

2 3

WARNING - RISK OF INJURY - Exercise care when using a foot bath. Use this product for its intended

purpose: a manicure chair and ll and drain indoor commercial appliance for foot and ankle hydro

massage. DO NOT use attachments not recommended by manufacturer.

WARNING - RISK OF ELECTRIC SHOCK - Do not permit electric appliances (such as hair dryers,

lamp, telephone, radio, or television) to be within 5 ft (1.5m) of this unit.

WARNING - To reduce the risk of burns, re, electric shock, or injury to persons:

• Unplug from outlet before putting on or taking off parts.

• Close supervision is necessary when this furnishing is used by, or near children, invalids, or dis-

abled persons. DO NOT leave children alone or allow them to operate the controls. Keep controls

out of reach of children.

• Never use this furnishing if it has a damaged cord or plug, if it is not working properly, if it has

been dropped or damaged, or dropped into water. Return the furnishing to a service center for

examination and repair.

• Keep the cord away from heated surfaces.

WARNING

• DO NOT reach for any electrical object that has fallen into the water. Unplug immediately.

• DO NOT drop or insert anything into jet opening, or any other opening.

• DO NOT operate without complete jet assembly installed or without water lled 1 inch above jets.

• DO NOT overll the basin.

• DO NOT stand on or in the basin, or on the foot rest.

• DO NOT leave this appliance unattended when in operation.

• DO NOT use outdoors.

• DO NOT tamper with any user-operated controls.

• Use heated surfaces carefully. May cause serious burns. Do not use over sensitive skin areas or in

the presence of poor circulation. The unattended use of heat by children or incapacitated persons

may be dangerous.

• Keep children away from sliding chair-back support mechanism.

• To avoid injury, exercise care when entering or exiting the chair and foot bath.

• Use caution when making positioning adjustments to your chair. Always ensure the wheels are

locked into position before you or client enters or exits the chair. Keep all equipment and body parts

away from moving parts while making any adjustments.

• It is important that you clean and disinfect the jets and basin after every use.

• Hydrotherapy should be pleasant and comfortable. Should you or a client experience any pain or

discomfort while using the foot bath, discontinue use immediately and consult a physician.

• You or your clients should consult a physician if diabetic, have poor circulation, if feet or legs are

inamed, have an open wound, or if you have questions about whether you should be using hydro

massage equipment.

• Make certain that the cord and plug are maintained in good condition and are not allowed to be-

come damaged while in use. Avoid positioning the cord in the trafc lane and it is always kept out

of the way. Take this product out of service immediately if the cord or plug becomes damaged in

any way.

• Do not attempt to repair. All repairs must be performed by an authorized service representative.

READ AND FOLLOW ALL INSTRUCTIONS

SAVE THESE INSTRUCTIONS

INSTALLER/OWNER BEARS ALL RESPONSIBILITIES TO COMPLY WITH STATE

AND LOCAL CODES WHEN INSTALLING THIS PRODUCT. FAILURE TO COMPLY

WITH THESE INSTRUCTIONS MAY VOID WARRANTY.

SECTION 1: CONSIGNES DE SÉCURITÉ

Symboles de sécurité ALERTE

Indique une situation potentiellement

dangereuse qui pourrait endommager

le matériel ou blesser un individu.

Veuillez vous familiariser avec les symboles

Sécurité & Avertissements. Ils ont été conçus

pour éviter les dommages corporels ou matériels

sur vous, vos clients et vos nouveaux produits

Living Earth Crafts.

DANGER

Indique une situation dangereuse

imminente qui causera des blessures

sérieuses, voire fatales (n’apparaît que

dans des conditions extrêmes).

Indique une situation potentiellement

dangereuse qui pourrait causer des

blessures sérieuses.

INSTRUCTIONS DE SÉCURITÉ IMPORTANTES

Les instructions de sécurité et les avertissements de ce manuel ne peuvent couvrir tous les prob-

lèmes et conditions pouvant exister. Faites preuve de bon sens et d’attention lors de l’installation,

de l’utilisation et de l’entretien de cet équipement.

À USAGE COMMERCIAL UNIQUEMENT - LISEZ TOUTES LES INSTRUCTIONS AVANT UTILI-

SATION

INSTRUCTIONS D’INSTALLATION

AVERTISSEMENT - L’utilisation de produits électroniques doit toujours être précédée de

certaines précautions de base, y compris :

LISEZ ET SUIVEZ TOUTES LES INSTRUCTIONS

CONSERVEZ CES INSTRUCTIONS

1. DANGER : RISQUE D’ÉLECTROCUTION. Connectez-vous uniquement sur un circuit protégé par

un disjoncteur de fuite à la terre.

2. Mise à la terre requise. L’unité doit être installée par un représentant de service qualié et mise à

la terre.

3. Votre bain de pied doit être installé par un plombier et un électricien agréés.

4. Si vous n’êtes pas certain que le produit soit connecté à un circuit DDFT et/ou correctement mis

à la terre, faites faire les vérications par un électricien qualié ou un technicien Ne modiez pas

la prise mâle fournie avec le produit. Si elle ne correspond pas à la prise femelle, faites installer le

branchement adapté par un électricien qualié.

5. Débranchez toujours cet équipement de la prise électrique avant son nettoyage et/ou son entretien.

AVERTISSEMENT - RISQUE D’HYPERTHERMIE ET POSSIBILITÉ DE NOYADE. Une

température de l’eau supérieure à 38 °C (100,4 °F) peut nuire à votre santé. Vériez et

ajustez la température de l’eau avant utilisation.

AVERTISSEMENT - L’utilisation d’alcool, drogue ou médicament peut grandement augmenter le

risque d’hyperthermie. N’UTILISEZ NI drogue, NI alcool avant d’utiliser le bain de pied.

Il y a hyperthermie lorsque la température interne du corps est au-dessus de la température normale

du corps (37 °C). Les symptômes de l’hyperthermie comprennent une augmentation de la température

du corps, vertiges, léthargie, somnolence et évanouissement. Les effets de l’hypothermie peuvent

inclure :

a) Inaptitude à ressentir la chaleur,

b) Inaptitude à identier le besoin de sortir du bassin d’hydromassage,

c) Inconscience d’un danger imminent,

d) Dommages au fœtus chez les femmes enceintes,

e) Incapacité physique à sortir du bassin d’hydromassage et

f) Évanouissement pouvant résulter en une noyade.

AVERTISSEMENT

L’INSTALLATEUR/PROPRIÉTAIRE EST TOTALEMENT RESPONSABLE DU RESPECT DES RÈGLES DE SON

ÉTAT ET DE SA LOCALITÉ LORS DE L’INSTALLATION DE CE PRODUIT. NE PAS SE CONFORMER À CES

INSTRUCTIONS PEUT ANNULER LA GARANTIE.

SECTION 1: CONSIGNES DE SÉCURITÉ

AVERTISSEMENT - RISQUE DE BLESSURE ACIDENTELLE OU DE NOYADE -

Les enfants et personnes handicapées ne doivent utiliser le bain de pied que sous la

supervision d’un adulte.

L’INSTALLATEUR/PROPRIÉTAIRE EST TOTALEMENT RESPONSABLE DU RESPECT DES RÈGLES DE SON

ÉTAT ET DE SA LOCALITÉ LORS DE L’INSTALLATION DE CE PRODUIT. NE PAS SE CONFORMER À CES

INSTRUCTIONS PEUT ANNULER LA GARANTIE.

AVERTISSEMENT - RISQUE DE BLESSURE - Soyez attentif lors de l’utilisation de ce bain de

pied. N’utilisez ce produit que pour l’usage auquel il est destiné : un fauteuil de manucure et un

appareil à utilisation commerciale et en intérieur avec arrivée et sortie d’eau pour hydromassage de

pied et cheville. N’UTILISEZ PAS d’accessoires non-recommandés par le fabricant.

AVERTISSEMENT - RISQUE D’ÉLECTROCUTION - Ne laissez pas d’appareils électriques (Ex :

sèche-cheveux, lampe, téléphone, radio, télévision) dans un rayon de 1,5 m (5 pieds) de cette

unité.

AVERTISSEMENT - Pour réduire le risque de brûlure, incendie, électrocution et blessure sur un

individu :

• Débranchez la prise mâle avant d’ajouter ou de retirer des parties de l’appareil.

• Une supervision attentive est nécessaire lorsque ce fauteuil est utilisé par ou près d’enfants, de

personnes invalides ou handicapées. NE LAISSEZ PAS des enfants seuls avec l’appareil et ne

les laissez pas le contrôler. Maintenez ses commandes hors de portée des enfants.

• N’utilisez pas ce fauteuil si le câble ou la prise mâle est endommagé, s’il ne fonctionne pas cor-

rectement, est tombé ou a été endommagé, ou s’il est tombé dans l’eau. Renvoyez le meuble

au centre de service pour un examen et une réparation.

• Maintenez le câble loin des sources de chaleur.

AVERTISSEMENT

• NE CHERCHEZ PAS à récupérer un objet électrique tombé dans l’eau. Débranchez immédiate-

ment l’objet.

• N’INSÉREZ rien et NE LAISSEZ rien TOMBER dans les ouvertures de jets d’eau, ni dans

aucune autre ouverture.

• N’UTLISEZ PAS l’appareil s’il n’a pas été complètement installé ou si l’eau n’est pas à plus de

2,5 cm au-dessus des jets d’eau.

• NE REMPLISSEZ PAS le bassin plus que nécessaire.

• NE MONTEZ PAS sur ou dans le bassin, ou sur le repose-pied.

• NE LAISSEZ PAS l’appareil sans surveillance pendant son utilisation.

• N’UTILSEZ PAS l’appareil en extérieur.

• NE MODIFIEZ PAS les commandes de l’utilisateur.

• Pour éviter toute blessure, soyez attentif au moment d’entrer et de sortir du fauteuil et du bain

de pied.

• Soyez attentif au moment d’ajuster la position du fauteuil. Assurez-vous toujours que les roues

sont bloquées au moment où vous ou votre client entrez ou sortez du fauteuil. Lors des ajuste-

ments, maintenez tout l’équipement et les membres du corps éloignés des parties en mouve-

ment.

• Il est important de nettoyer et désinfecter les jets d’eau et le bassin après chaque utilisation.

• L’hydrothérapie doit être une expérience plaisante et confortable. Si vous ou votre client ressen-

tez une douleur ou un inconfort lors de l’utilisation du bain de pied, mettez-y n immédiatement

et consultez un médecin.

• Consultez un médecin si vous ou votre client êtes diabétique, avez une mauvaise circulation

sanguine, si vos pieds ou vos jambes sont enammés, si vous avez une blessure ouverte ou si

vous ignorez si vous pouvez utiliser l’équipement d’hydromassage.

• Assurez-vous que le câble et la prise mâle sont en bon état et ne risquent pas d’être endom-

magés lors de l’utilisation. Évitez de placer le câble sur les voies de déplacement pour éviter

qu’il ne se trouve sur le chemin de qui que ce soit. Si le câble ou la prise est endommagé, de

quelque manière que ce soit, mettez immédiatement le produit hors service.

• Ne tentez pas de le réparer. Toutes les réparations doivent être effectuées par un représentant

de service autorisé.

LISEZ ET SUIVEZ TOUTES LES INSTRUCTIONS

CONSERVEZ CES INSTRUCTIONS

Club Chair V2 Mysa 5th Avenue

Product

Image*

Chair Overall

Dimensions 49”H x 32”W x 38.5”D 45.5”H x 30.25”W x 35”D 48”H x 32”W x 36.75”D

Tub Overall

Dimensions 15.5”H x 22”W x 26.5”D 15.5”H x 22”W x 26.5”D 15.5”H x 22”W x 26.5”D

Tub Basin

DImensions 9”D x 14.75”W x 15”L 9”D x 14.75”W x 15”L 9”D x 14.75”W x 15”L

Seat Height

(from oor) 24” H 24” H 24” H

Locaon of

Tilt Lever

(Oponal)

Inside panel on the right-

hand side

Outside panel on the

right-hand side

Outside panel on the

right-hand side

Tilt Angle

(Oponal) 20 degree lt range 20 degree lt range 20 degree lt range

Cushioning Strata™ Memory Foam

Cushioning System

Strata™ Memory Foam

Cushioning System

Strata™ Memory Foam

Cushioning System

Upholstery Naturso® Naturso® Ultraleather® or Promessa®

Other

Opons

Relaxor® Heat/Massage

DIscharge Pump

Swingaway Nail Trays

Relaxor® Heat/Massage

DIscharge Pump

Swingaway Nail Trays

Relaxor® Heat/Massage

DIscharge Pump

Swingaway Nail Trays

SECTION 2 : PRODUCT OVERVIEW

*all products shown with oponal accessories and/or nishes. Measurements may vary due to natural material variaons 6

6 7

SECTION 2 : PRODUCT OVERVIEW

Plumbed Tub Overview

Footrest

Adjustment

Knob

Power Buon - Lights*

Power Buon - Jets*

Power Buon - Discharge

Pump (Oponal)

Remote Drain

Handle

Tub Basin

Water Control

Valve (Fill &

Temperature)

Drain

Light*

Jets*

Sprayer/Fill

Reexology*

*Features are on hydrotherapy tub only

SECTION 3 : OPERATING INSTRUCTIONS

Water Control Valve (Fill & Temperature)

CAUTION

There is no automac shuto with the water ll valve. You MUST turn the valve OFF

aer the tub is lled to prevent overow and/or ooding. Do not walk away from the

tub when it is lling with water. An adequate drainage system must be provided to deal

with overow water.

Sanijet® Pipeless Jets (Hydrotherapy Tub Only)

Down-OffUp-FillLeft-Cold Right-Hot

The water control valve is OFF when poinng DOWN. Water dispenses when you pull the valve

UP. Hot water is dispensed when the valve is turned to the RIGHT. Cold water is dispensed when

the valve is turned to the LEFT.

Pressing the On/O buon once will start the jets, and pressing the buon again will turn the

system o. Turn on the jets ONLY AFTER the tub is lled with water, and ensure you turn the

jets OFF before draining the tub.

CAUTION

Running the jets without lling the tub with water can damage or destroy the jets.

Ensure that a MINIMUM of one (1) inch of water is above the jets prior to use.

Power Buon - Jets

Chromasoothe Light (Hydrotherapy Tub Only)

Pressing the light buon once will turn the light to the default Bright White color. Press the

buon again to cycle to the next color mode, in the following order:

1. Bright White

2. Aqua Blue

3. Soothing Blue

4. Ocean Blue

5. Majesc Gold

6. Shamrock Green

7. Fiery Red

8. Chameleon Mode

9. Party Mode

To reset, turn lights o for 5 seconds and turn back on.

Lights will ash 4 mes and return to Bright White.

Power Buon -

Lights

8 9

SECTION 3 : OPERATING INSTRUCTIONS

Adjustable Locking Footrest

There are four locking posions on the footrest. It is controlled by the locking knob on the front

of the tub. Pulling the knob will free the footrest to move up or down to the desired posion.

Releasing the knob will lock it into posion.

CAUTION

Be careful of pinch points when adjusng the footrest. Always ensure the footrest is

supported unl the knob is securely locked into place.

Knob In - Locked Knob Out - Unlocked

Remote Drain Handle

Pull the handle up and back (clockwise) to close the drain when lling the tub. Push the handle

down and parallel to the oor (counterclockwise) to open the drain and empty the tub.

Push handle away from the

footrest (counterclockwise)

to open/drain

Pull handle towards foot-

rest (clockwise) to close/ll

Discharge Pump (Optional)

The discharge pump is controlled by the buon next to the remote drain handle. Before

pressing the discharge pump to empty the tub, rst open the drain with the remote drain

handle and let the water start draining toward the pump. Wait approximately 5-10 seconds for

the pump to register, then push the discharge pump buon.

Discharge Pump Buon

SECTION 3: OPERATING INSTRUCTIONS

Rolling the Pedicure Chair

CAUTION

Be careful of pinch points when rolling the chair back and forth.

Your pedicure chair is mounted on four (4) casters/wheels. The two (2) locking casters are

located at the rear of the chair.

These casters allow the chair to roll smoothly back and forth over the top of the staonary

pedicure tub. The locking casters only roll forward and backward, and do not swivel. Make sure

the chair lines up directly over the tub and rolls parallel to it. The chair comes equipped with

heavy duty plasc tub guards to protect both the chair and tub.

Foot

Brake

With your foot, press DOWN on

the foot brake.

Brake

Release

With your foot, push FORWARD

on the brake release.

Locking the wheel

Unlocking the wheel

Chair rolls forward &

backward over tub

Pneumatic Back Tilt (Optional)

Locate the lever on the right side of the chair (may be inside or outside the armrest depending

on model). While sing in the chair, pull the lever and lean on the back rest unl you have

reached the desired angle. Pulling the lever again and taking your weight o the back rest will

return the back rest to its original upright posion.

*generic diagram for illustraon purposes only - chair model varies

SECTION 3: OPERATING INSTRUCTIONS

10 11

Relaxor® Heat & Massage (Optional)

The following diagrams illustrate the ease-of-use and funconality that the Relaxor® system

provides to you and your clients.

SELECT

PULSE

Ultra

PWR

LO HI

Power

Lower Back Heat - High

Lower Back Heat - Low

Massage All Zones - Connuous

Massage All Zones - Sequenal

Massage All Zones - Short Bursts

Raise Massage Intensity

Raise Massage Speed

Upper Back Massage

Mid Back Massage

Low Back Massage

Lower Massage Intensity

Lower Massage Speed

DANGER - RISK OF ELECTRIC SHOCK

Keep hand control and all electrical components away from water.

PWR

• Massage 15 Minute Timer (Standard)

• Massage 30 Minute Timer (Hold Down Button)

• Indicates Active Button

• Indicates Normal Standby

• Indicates High Mode

• Indicates Low Mode

Green Light

Blue Light

Red Light

Orange Light

Symbol Description

SECTION 3: OPERATING INSTRUCTIONS

Swingaway Manicure Trays (Optional)

The Swingaway Manicure Trays are a convenient way to oer manicure services in your

pedicure chair. Each tray has a post at the narrow end that can be dropped into the receivers

aached to the armrests. When not in use, your chair is equipped with convenient storage

receivers towards the back of the armrests.

To Set Up:

Insert the tray post into the receiver and

push straight down to secure.

*Club Chair V2 shown for illustrave purposes - funconality is the same for all chair models 12

To Remove:

Li tray evenly with one hand placed on

either side of the receiver. Tray may get

stuck if only lied from one side.

To Store:

Insert the tray post into the storage

receiver, and push all the way in to

prevent the tray from falling out.

The manicure trays can easily be swiveled to any posion that is desired. Below are the most

commonly used tray posions and their funcons.

Posion 1: Places trays closer to the client and allows the magnec center tray to be aached.

Posion 2: Places trays closer to the technician and provides more room for the client.

Posion 3: Allows the trays to funcon as extended armrests or table.

position 1 position 2 position 3

Overhead view

Tray Positioning

SECTION 3: OPERATING INSTRUCTIONS

Magnetic Center Tray (Optional)

The Magnec Center Tray provides even more surface area for your manicure services. If

ordered, at the me of manufacturing both your Swingaway Manicure Trays and Center Tray

will be equipped with embedded magnets to hold the trays into a locked posion.

Your Magnec Center Tray is stored in a zippered compartment within the backrest. To access,

simply unzip and pull the tray out of the storage compartment. Place the center tray on the

Swingaway Manicure Trays, and move it slightly back and forth unl the magnets “catch”.

The nished conguraon will look like the photo below:

12 13

Swingaway Manicure Tray Dimensions

11.5”

23.5”

11.5”

23.5”

SECTION 4: CARE & MAINTENANCE

Tub Cleaning Guide

Cleaning After Each Use/Client

1. Drain the tub of all water.

2. Rotate the jet cover to unlock. (Fig. 1)

3. Remove the jet cover. (Fig. 2)

4. Remove the magnec impeller/rotor from the jet case. (Fig. 3)

5. Place jet cover and impeller/rotor into a sink. Use a non-abrasive anbacterial cleaner and

clean brush to remove any visible residue. Rinse with fresh water, and dry with a clean

paper towel.

6. Use a non-abrasive anbacterial cleaner and clean brush to scrub and clean the tub basin,

drain stopper, and light casing, followed by a rinse with fresh water.

7. Rell the tub with clean water and add the correct amount (read manufacturer label for

mixing instrucons) of an EPA-registered liquid disinfectant that is labeled as a bactericide,

fungicide, and virucide. Turn on the jets to circulate the water for at least 10 minutes.

8. Drain the tub, rinse with fresh water, and wipe dry with a clean paper towel.

9. Reinstall the magnec impeller/rotor.

10. Reinstall the jet cover by aligning at the 10 o’clock posion. Maintain even pressure and

rotate jet cover to lock into place at the 3 or 9 o’clock posion.

IMPORTANT: Jets will not run if not locked into place properly.

Fig. 1 Fig. 2 Fig. 3

CAUTION

- Always refer to your state and local codes for specic cleaning requirements.

- NEVER USE abrasive cleaners on any surface area. Failure to comply can cause damage

and void your warranty.

Foot Bath Additives

Provide an enhanced pedicure experience with essenal oils, aromatherapy, and other addives,

knowing all residue can be easily removed. The Sanijet® foot bath can be used with most foot and

skin care products, provided that the cleaning protocols and local codes are strictly followed.

Products NOT Recommended

• Silicate based bath addives/scrubs - may void warranty.

• High foam agents (use only low foam soluons).

• Abrasive cleaners that might damage the system components, and scratch/dull the basin

surface (major scratches will require professional renishing.

• To avoid discoloraon, products with petroleum disllates must not remain on surfaces.

SECTION 4: CARE & MAINTENANCE

Tub Cleaning Guide

Cleaning At the End of Each Day

1. Drain the tub of all water.

2. Rotate the jet cover to unlock. (Fig. 1)

3. Remove the jet cover. (Fig. 2)

4. Remove the magnec impeller/rotor from the jet case. (Fig. 3)

5. Place jet cover and impeller/rotor into a sink. Use a non-abrasive anbacterial cleaner and

clean brush to remove any visible residue. Rinse with fresh water, and dry with a clean

paper towel.

6. Use a non-abrasive anbacterial cleaner and clean brush to scrub and clean the tub basin,

drain stopper, and light casing, followed by a rinse with fresh water.

7. Fill the tub with warm water and detergent and turn on the jets to circulate water/

detergent through the spa system for at least 10 minutes.

8. Drain the detergent soluon and rinse the basin.

9. Rell the tub with clean water and add the correct amount (read manufacturer label for

mixing instrucons) of an EPA-registered liquid disinfectant that is labeled as a bactericide,

fungicide, and virucide. Turn on the jets to circulate the water for at least 10 minutes.

10. Drain the tub, rinse with fresh water, and wipe dry with a clean paper towel.

11. Reinstall the magnec impeller/rotor.

12. Reinstall the jet cover by aligning at the 10 o’clock posion. Maintain even pressure and

rotate jet cover to lock into place at the 3 or 9 o’clock posion.

IMPORTANT: Jets will not run if not locked into place properly.

Cleaning Once a Week

1. Follow steps 1-9 of the “At the End of Each Day” instrucons above.

2. DO NOT DRAIN the disinfectant soluon. Aer circulang for 10 minutes, turn o the jets

and leave the disinfectant soluon undisturbed in the tub for at least 6 hours.

3. Aer at least 6 hours, drain and rinse the tub basin with clean water.

4. Rell the tub with clean water and ush the system.

5. Wipe dry with a clean paper towel.

6. Reinstall the magnec impeller/rotor.

7. Reinstall the jet cover by aligning at the 10 o’clock posion. Maintain even pressure and

rotate jet cover to lock into place at the 3 or 9 o’clock posion.

IMPORTANT: Jets will not run if not locked into place properly.

SECTION 4: CARE & MAINTENANCE

CAUTION

DO NOT USE acetone, paint thinner, bleach, “Armor All” type cleaners, or industrial

cleaners. These will damage the upholstery’s protecve coang.

Do not place nail care products on the Foot Bath.

Extended exposure to chemicals can damage the basin, footrest, and/or upholstery.

Failure to comply with all cleaning instrucons can cause damage to your foot bath

and pedicure chair, and void the warranty.

DANGER: RISK OF ELECTRIC SHOCK

Always unplug this furnishing from the electrical outlet before cleaning.

Your pedicure chair is relavely maintenance free. However, to ensure your chair will connue

to funcon properly and keep its appearance, we recommend the following:

Category Care Recommendation

Upholstery

Remove day-to-day dirt and smudges with a mild soap and water soluon.

For tough stains and to disinfect, use a (100 to 1) water to bleach soluon.

Spray a damp cloth with the soluon to clean.

Aer each cleaning, gently wipe the upholstery with a damp cloth and clean

water, then allow upholstery to air dry before using or storing.

For more dicult stains, please contact your dealer or please call us directly

for guidance. For best results, use only the products suggested above.

Laminate

Never use abrasive cleaners. A mild liquid detergent and warm water will

clean soiled surfaces. To avoid discoloraon, cleaners containing petroleum

disllates must not remain on surfaces.

Wood To maintain the wood nish and retouch scratches, use a high quality

furniture wax.

Electronics An-stac electronic aerosol dusters can be used to keep the surfaces of

electronic components, power cables, and plugs free of dust.

Lubricaon &

Mechanical

If necessary, lubricate wheel joints, casters, and other mechanical parts with

a light machine oil. Periodically check and ensure all visible bolts remain

ghtened.

Pedicure Chair Cleaning & Ongoing Maintenance

SECTION 4: CARE & MAINTENANCE

This helpful troubleshoong guide will provide you with informaon about how to recognize a

problem with your product, determine possible causes, and nd a soluon.

In the event your specic situaon is not covered in this guide, please contact Living Earth Cras

so our technical support department can assist you. Beyond the troubleshoong guide below, do

not aempt to repair the issue yourself. This can void your warranty.

Unauthorized service will not be covered. Please be sure to contact Living Earth Cras Customer

Service rst at (800) 358-8292, (760) 597-2155 Int’l.

Troubleshooting

Issue Solution

No Power to

Relaxor/Relaxor

Not Operang

1. Ensure the power cord is properly plugged into an operaonal

grounded power supply/outlet.

2. Check GFCI reset and circuit breakers or fuses.

3. Ensure the outlet in your room is receiving power. This can be done

by plugging in a small appliance and turning it on.

No Power to

Jets/Jets not

Operang

1. Ensure the power cord is properly plugged into an operaonal GFCI

power supply/outlet.

2. Check GFCI reset and circuit breakers or fuses.

3. Check jets are locked into the 9’oclock or 3 o’clock “run” posion.

4. Ensure magnec rotor/impeller is correctly installed in the case.

5. Reset the motors by unplugging the system, waing 5 seconds, then

plugging in again.

Excessive Noise

from Jets

1. Remove jet assembly and inspect for dirt buildup, debris, or damage.

2. Follow cleaning instrucons or replace if necessary.

Water Leakage

1. Check and ensure all visible bolts are ghtened.

2. Call a plumber to determine the source of the leak.

3. If the leak is from the jet system, contact LEC customer service.

SECTION 4: CARE & MAINTENANCE

Electrical Specications

Spec North America Europe/Asia

Input Voltage 120 VAC 220 VAC

Input Frequency 60 Hz 50 Hz

Total Consumpon - All

Opons 8.5 Amps Max 4.6 Amps Max

Consumpon - Chair &

Hydrotherapy Tub Only 4 Amps Max 2.2 Amps Max

Consumpon - Relaxor Addional 3 Amps (Max) Addional 1.6 Amps (Max)

Consumpon - Discharge

Pump Addional 1.5 Amps (Max) Addional 0.8 Amps (Max)

Motor Design Single speed, electronic spherical DC motor with magnec

rotor impeller

Motor Materials Thermoplasc jet, motor, and case assembly; stainless steel

rotor impeller

Motor Safety Features Safety shuto sensor, dry-run/thermal overload protecon

Supply Connecons 1/2” NPT (Recommended) / 1.27 cm

Drain Outlet 1.5” / 3.81 cm

Warranty Information

Living Earth Cras (LEC) oers an industry best one (1) year warranty, worldwide, on all

Pedicure Chairs and accessories. Foam and upholstery covering are warranted for three (3)

years. Hydraulic systems, motors, controls, and actuators are warranted for two (2) years,

including parts and labor. Accessories and opons are warranted for one (1) year, unless

otherwise noted. LED may repair or replace defecve components at our discreon. LEC will

return the warranted product, standard shipping pre-paid, to customers in the connental

US. Internaonal customers are responsible for any applicable dues and taxes, as well as all

shipping charges inbound and outbound. Normal wear and tear, and costs associated with

maintenance procedures, and damage caused by accident, misuse, improper maintenance,

harsh operang environments or neglect (which includes tears in the upholstery and damage

caused by harsh chemical-based cleaners) are not covered under this warranty. All warranes

are limited to repair or replacement, at LEC’s discreon, unless otherwise stated.

La page charge ...

Living Earth Crafts Mystia Manuel utilisateur

Marque: Living Earth Crafts

Modèle: Mystia

Catégorie: Masseurs

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Living Earth Crafts Mystia User manual

Living Earth Crafts Mystia Manuel utilisateur

Living Earth Crafts Mystia Manuel utilisateur

dans d''autres langues

Autres documents