Allen-Bradley 140MG-H Adjustment Instruction

Marque: Allen-Bradley

Modèle: 140MG-H

Taper: Adjustment Instruction

Bul. 140MG

DIR 1000721R0507 Version 04

WARNING: To prevent electrical shock, disconnect from power source before

installing or servicing. Install in suitable enclosure. Keep free from contaminants.

(Follow NFPA70E requirements).

AVVERTENZA: Per prevenire infortuni, togliere tensione prima dell'installazione o

manutenzione. Installare in custodia idonea. Tenere lontano da contaminanti.

WARNUNG: Vor Installations- oder Servicearbeiten Stromversorgung zur

Vermeidung von elektrischen Unfällen trennen. Die Geräte müssen in einem

passenden Gehäuse eingebaut und gegen Verschmutzung geschützt werden.

AVERTISSEMENT: Avant le montage et la mise en service, couper l'alimentation

secteur pour éviter toute décharge. Prévoir une mise en coffret ou armoire appropriée.

Protéger le produit contre les environnements agressifs.

ADVERTENCIA: Desconéctese de la corriente eléctrica, antes de la instalación o

del servicio, a fin de impedir sacudidas eléctricas. Instálelo en una caja apropiada.

Manténgalo libre de contaminantes.

ATENÇÃO: Para evitar choques, desconectar da corrente elétrica antes de fazer a

instalação ou a manutenção. Instalar em caixa apropriada. Manter livre de

contaminantes.

Installation - Installazione - Instalación

Instalação - -

DIR 1000721R0507 Version 04 - 140MG-H8E_, 140MG-J8E_

140MG-J

140MG-H

CLACK

警告：感電事故防止のため、取付けまたは修理の際は電源から取り外してく

ださい。適切なケース内に取付けてください。また、汚染物質がないことを

確認してください。

警告：为了防止触电，在安装或维修之前必须先切断电源。安装在合适的设备

箱内。防止接触污染。物

1000721R0507

* fold this paper with barcode on the outer side

Adjustment Instruction for 140MG-H, 140MG-J

Settaggio sganciatori

Auslöser

Dèclencheur

Relé

Green

L Red LED Fully illuminated = L pre alarm (0.9 I1 < I < 1.2 I1) LED Flashing = Overcurrent fault (I > 1.2 I1)

U Red

L | U | I Red LED Flashing = Trip Coil disconnected

LED Color CONDITION Run time

LED Flashing = Phase Unbalance

and

2s<ti<3s

5E 3s<ti<5s @ (7.2 x I1)

10E 5s<ti<10s

20E 10s<ti<20s

In = 100 A

= 100 x (0.4+0.08+0.32)= 80A

CLASS = 3E@(7.2xI1)=2s<ti<3s@576A(7.2Ax80)

Example:

=100 x (6+1+2)=900A

In=100 A

Settaggio di default

Default-Einstellung

Configuration par défauit

Ajuste de default

Example:

CLASS

min (L1, L2, L3) < 0.1In

max (L1, L2, L3) > 0.5 I1

I6=

{

U = ON

CLASS

t6 = 2s

(2)

M-LIU

Default setting

DIR 1000721R0507 Version 04

140G-ELTT is required for fault identification in compliance with UL508A

CLACK

140G-ELTT

(Ordered separately)

LED

- Green

- Verde

- Grün

- Vert

- Verde

- Red

- Rosso

- Rot

- Rouge

- Rojo

- Device ON

- Dispositivo acceso

- Einrichtung eingeschaltet

- Dispositif allumé

- Dispositivo encendido

- Change battery

- Sostituire batterie

- Batterie ersetzen

- Remplacer batteries

- Sustituir baterías

DIR 1000721R0507 Version 04 (B0399) - B1581

Allen-Bradley, Rockwell Software, and Rockwell Automation are trademarks of Rockwell Automation, Inc.

Trademarks not belonging to Rockwell Automation are property of their respective companies.

Publication 140G-IN101E-MU-P - August 2017

Rockwell Automation maintains current product environmental compliance information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/

sustainability-ethics/product-environmental-compliance.page

PROCEDURA DI CONTROLLO

- CONTROLLO LED:

tutti i led del relè si

devono accendere

- ULTIMA INDICAZIONE DI TRIP:

Il LED si accende solo quando

avviene un trip

- LED:

resta acceso finchè 140G-ELTT

Tester è connessa al relè

- PRONTO PER TRIP

- Fasi 2 e 3 per test Trip Unit

DIAGNOSTIC PROCEDURE

- UNIT CHECK LED:

all the LEDs in the relay

must come on

- LAST TRIP INDICATION:

LED will come on only

when a trip occured

- LED: remains on for

as long as the 140G-ELTT

Tester is connected to

the relay

- READY TO TRIP

- Steps 2 & 3 to test Trip Unit

DIAGISTIKABLAUF

- EINEITHSPRUF-LED:

Alle LEDs des Relais müssen

aufleuchten

- ANGABE DER LETZTEN AUSLOSUNG:

LED leuchtet nur, wenn es eine

trip.

- LED: Bleibt angeschaltet,

bis die Einheit 140G-ELTT Tester

an die Relais angeschlossen ist.

- AUSLOSEBEREIT

- Stufe 2 und 3 um zu Trip Unit testen

PROCEDIMIENTO DIAGNOSTICO

- LED CONTROL UNIDAD: todos los

led del relé se deben

encender

- INDICACION ULTIMA ACTUACION:

LED se enciende sólo cuando hay

un trip

- LED: queda encendido

mientras la 140G-ELTT Tester

permanezca conectada con el relé

- LISTO PARA LA ACTUACION

- Fase 2 y 3 para Trip Unit test

PROCÉDURE DE DIAGNOSTIC

- UNIT CHECK LED : toutes les

diodes du relais doivent

s'allumer

- LAST TRIP INDICATION :

la DIODE allume seulement

quand il ya un trip

- LED: la DIODE reste

allumée tant que 140G-ELTT

Tester est connectée au relais

- READY TO TRIP

- Phase 2 et 3 pour test Trip Unit

Allen-Bradley 140MG-H Adjustment Instruction

Marque: Allen-Bradley

Modèle: 140MG-H

Taper: Adjustment Instruction

Télécharger le PDF

rapport

Allen-Bradley 140MG-H Adjustment Instruction

Allen-Bradley 140MG-H Adjustment Instruction

dans d''autres langues

Documents connexes

Autres documents