MSI MS-7151 Le manuel du propriétaire

i

MS-7151 (v1.X) ATX Mainboard

G52-M7151X4

RX480 Neo2

English/French/German Version

未命名-1 2005/10/31, 下午 04:171

ii

FCC-B Radio Frequency Interference Statement

This equipment has been tested and found to comply with the limits for a class B

digital device, pursuant to part 15 of the FCC rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Opera-

tion of this equipment in a residential area is likely to cause harmful interference, in

which case the user will be required to correct the interference at his own expense.

Notice 1

The changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

Notice 2

Shielded interface cables and A.C. power cord, if any, must be used in order to

comply with the emission limits.

VOIR LA NOTICE D’INSTALLATION AVANT DE RACCORDER AU RESEAU.

Micro-Star International

MS-7151

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may

cause undesired operation.

未命名-1 2005/10/31, 下午 04:172

iii

Copyright Notice

The material in this document is the intellectual property of MICRO-STAR

INTERNATIONAL. We take every care in the preparation of this document, but no

guarantee is given as to the correctness of its contents. Our products are under

continual improvement and we reserve the right to make changes without notice.

Trademarks

All trademarks are the properties of their respective owners.

AMD, Athlon™, Athlon™ XP, Thoroughbred™, and Duron™ are registered trade-

marks of AMD Corporation.

Intel

®

and Pentium

®

are registered trademarks of Intel Corporation.

PS/2 and OS

®

/2 are registered trademarks of International Business Machines

Corporation.

Windows

®

95/98/2000/2003/NT/XP are registered trademarks of Microsoft Corporation.

Netware

®

is a registered trademark of Novell, Inc.

Award

®

is a registered trademark of Phoenix Technologies Ltd.

AMI

®

is a registered trademark of American Megatrends Inc.

Revision History

Revision Revision History Date

V1.0 First Release of 7151 v1.x PCB August 2005

with ATI RX480/SB400 chipsets

V1.1 First Release of 7151 v1.x PCB November 2005

with ATI RX480/SB400 chipsets (for EU)

Technical Support

If a problem arises with your system and no solution can be obtained from the user’s

manual, please contact your place of purchase or local distributor. Alternatively,

please try the following help resources for further guidance.

Visit the MSI website for FAQ, technical guide, BIOS updates, driver updates,

and other information: http://www.msi.com.tw/program/service/faq/

faq/esc_faq_list.php

Contact our technical staff at: support@msi.com.tw

未命名-1 2005/10/31, 下午 04:173

iv

1. Always read the safety instructions carefully.

2. Keep this User’s Manual for future reference.

3. Keep this equipment away from humidity.

4. Lay this equipment on a reliable flat surface before setting it up.

5. The openings on the enclosure are for air convection hence protects the equip-

ment from overheating. DO NOT COVER THE OPENINGS.

6. Make sure the voltage of the power source and adjust properly 110/220V be-

fore connecting the equipment to the power inlet.

7. Place the power cord such a way that people can not step on it. Do not place

anything over the power cord.

8. Always Unplug the Power Cord before inserting any add-on card or module.

9. All cautions and warnings on the equipment should be noted.

10. Never pour any liquid into the opening that could damage or cause electrical

shock.

11. If any of the following situations arises, get the equipment checked by a service

personnel:

† The power cord or plug is damaged.

† Liquid has penetrated into the equipment.

† The equipment has been exposed to moisture.

† The equipment has not work well or you can not get it work according to

User’s Manual.

† The equipment has dropped and damaged.

† The equipment has obvious sign of breakage.

12. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT UNCONDITIONED, STOR-

AGE TEMPERATURE ABOVE 60

0

C (140

0

F), IT MAY DAMAGE THE EQUIPMENT.

Safety Instructions

CAUTION: Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the

manufacturer.

未命名-1 2005/10/31, 下午 04:174

v

WEEE Statement

未命名-1 2005/10/31, 下午 04:175

vi

未命名-1 2005/10/31, 下午 04:176

vii

未命名-1 2005/10/31, 下午 04:177

viii

CONTENTS

FCC-B Radio Frequency Interference Statement...........................................................ii

Copyright Notice.............................................................................................................iii

Revision History.............................................................................................................iii

Technical Support.........................................................................................................iv

Safety Instructions........................................................................................................iv

English.......................................................................................................................E-1

User’s Manual.......................................................................................................E-3

Français....................................................................................................................F-1

Manuel d’utilisation...............................................................................................F-3

Deutsch....................................................................................................................G-1

Benutzerhandbuch.............................................................................................G-3

未命名-1 2005/10/31, 下午 04:178

E-1

User’s Manual

RX480 Neo2 Series

User’s Manual

English

E-2

MS-7151 ATX Mainboard

E-3

User’s Manual

Chapter 1. Getting

Started

RX480 Neo2 Series

User’s Manual

Thank you for choosing the RX480 Neo2 (MS-7151 v1.X) ATX

mainboard. The RX480 Neo2 mainboard is based on ATi

®

RX480 &

ATi

®

SB400 chipsets for optimal system efficiency. Designed to fit the

advanced AMD

®

K8 Athlon 64 FX processor, the RX480 Neo2 deliv-

ers a high performance and professional desktop platform solution.

E-4

MS-7151 ATX Mainboard

Mainboard Specifications

CPU

† Supports 64-bit AMD

®

Athlon 64 and Athlon 64 FX processor (Socket 939)

† Supports up to 4200+ Athlon 64 FX or higher CPU

(For the latest information about CPU, please visit http://www.msi.com.tw/pro-

gram/products/mainboard/mbd/pro_mbd_cpu_support.php)

Chipset

† ATI

®

RX480 Chipset

- HyperTransport

TM

connection to AMD K8 Athlon64 processor

- 8 or 16 bit control/address/data transfer both directions

- 1000/800/600/400/200 MHz “Double Data Rate” operation both direction

- Compliant with PCI Express 1.0a specifications (one x16 graphics interface,

which can be divided into two smaller links for use by other devices)

† ATI

®

SB400 Chipset

- Supports dual channel native SATA controller up to 150MB/s with RAID 0 or 1

- Integrated Hardware Sound Blaster/Direct Sound AC97 audio

- Ultra DMA 66/100/133 master mode PCI EIDE controller

- ACPI & PC2001 compliant enhanced power management

- Supports USB2.0 up to 8 ports

Main Memory

† Supports dual channel, four memory banks DDR 333/400, using two 184-pin

DDR DIMMs

† Supports a maximum memory size up to 2GB without ECC

† Supports 2.5v DDR SDRAM DIMM

(For the updated supporting memory modules, please visit http://www.msi.com.

tw/program/products/mainboard/mbd/pro_mbd_trp_list.php.)

Slots

† One PCI Express x16 slot (supports PCI Express Bus specification v1.0a compliant)

† One PCI Express x1 slot

† Four 32-bit Master 3.3V/5V PCI Bus slots

Onboard IDE

† An IDE controller on the ATI

®

SB400 chipset provides IDE HDD/CD-ROM with PIO,

Bus Master and Ultra DMA 133/100/66 operation modes, 4X ultra DMA 100/66/33

† Can connect up to 4 IDE devices

Onboard Serial ATA

† Supports 4 SATA ports with up to 150MB/s transfer rate

E-5

User’s Manual

USB Interface

† 8 USB ports

- 4 ports in the rear I/O, 4 ports via the external bracket

LAN (optional)

† Realtek

®

8100C/8110SB LAN chip (Optional)

- Integrated Fast Ethernet MAC and PHY in one chip

- Supports 10Mb/s and 100Mb/s and 1000Mb/s (1000Mb/s for 8110SB only)

- Compliance with PCI v2.2

- Supports ACPI Power Management

Audio

† 8 channels software audio codec RealTek ALC850

- Compliance with AC97 v2.3 Spec.

- Meets PC2001 audio performance requirement.

On-Board Peripherals

† On-Board Peripherals include:

- 1 floppy port supports 1 FDD with 360K, 720K, 1.2M, 1.44M and 2.88Mbytes

- 2 serial ports (COM1 on the rear, COM2 with pinheader)

- 1 parallel port supporting SPP/EPP/ECP mode

- 8 USB2.0 ports (Rear*4/Front*4)

- 1 Audio (Line-Outx3, Line-In, MIC In, SPDIF Out (Coaxial/Fibre) port

- 1 RJ-45 LAN Jack

- 2 IDE ports support 4 IDE devices

- 4 serial ATA ports

BIOS

† The mainboard BIOS provides “Plug & Play” BIOS which detects the peripheral

devices and expansion cards of the board automatically.

† The mainboard provides a Desktop Management Interface (DMI) function which

MSI Reminds You...

1.Please note that users cannot install OS, either WinME or Win98,

in their SATA hard drives. Under these two OSs, SATA can only be

used as an ordinary storage device.

2.To create a bootable RAID volume for a Windows 2000 environment,

Microsoft’s Windows 2000 Service Pack 4 (SP4) is required. As

the end user cannot boot without SP4, a combination installation

CD must be created before attempting to install the operating sys-

tem onto the bootable RAID volume.

To create the combination installation CD, please refer to the fol-

lowing website:

http://www.microsoft.com/windows2000/downloads/

servicepacks/sp4/HFdeploy.htm

E-6

MS-7151 ATX Mainboard

records your mainboard specifications.

† Supports boot from LAN, USB Device 1.1 & 2.0, and SATA HDD.

Dimension

† ATX Form Factor: 30.5cm X 21.5cm

Mounting

† 6 mounting holes

E-7

User’s Manual

Mainboard Layout

RX480 Neo2 (MS-7151 v1.X) ATX Mainboard

1

4

5 5

6

3

2

4

2

7

6

4

8

9

10

1111

12

13

14

16

15

16

15

E-8

MS-7151 ATX Mainboard

1

2

4

3

6

5

7

9

11

8

ATX 24-Pin Power Connector: JPWR1 This connector allows you to

connectto an ATX power suply.

ATX 12V Power Connector: JPWR2, JPWR3 This power connector is

provided to connect 12V power suply.

Floppy Disk Drive Connector: FDD1 This mainboard provides a stand-

ard floppy disk drive connector that supports 360K, 720K, 1.2M, 1.44M and

2.88M floppy disk types.

Fan Power Connecors: CPU_FAN, NB_FAN, SYS_FAN These fan

connectors support system cooling fan with +12V.

ATA 133 Hard Disk Connectors: IDE1 & IDE2 This mainboard has a 32-

bit Enhanced PCI IDE and Ultra DMA 66/100/133 controller that provides PIO

mode 0~4, Bus Master and Ultra DMA 66/100/133 function.

Serial ATA/ Serial ATA Connectors controlled by ATI SB400: SATA1 /

SATA2 / SATA3 / SATA4 The chipset of this mainboard is SB400 which

supports four serial ATA connectors SATA1~SATA4. SATA1~SATA4 are

high-speed Serial ATA interface ports. Each supports serial ATA data rate

of 150 MB/s.

Chassis Intrusion Switch Connector: JCI1 This connector is con-

nected to a 2-pin chassis switch. If the chassis is opened, the switch will

be short.

CD-In Connector: JCD1 The connector is for CD-ROM audio connector.

Front Panel Audio Connector: JAUD1 This front panel audio connector

allows you to connect to the front panel audio.

Serial Port Header: JCOM1 (Optional) The mainboard offers one 9-pin

header as serial port to attach a serial mouse or other serial devices.

Front Panel Connectors: JFP1, JFP2 The mainboard provides one front

panel connector for electrical connection to the front panel switches and

LEDs.

10

JFP2

7

8

Power LED

Speaker

1

2

JFP1

1

2

9

10

HDD

LED

Reset

Switch

Power

LED

Power

Switch

E-9

User’s Manual

14

12

13

15

16

IrDA Infrared Module Header: JIR1 The connector allows you to

connect to IrDA Infrared module. You must configure the setting through

the BIOS setup to use the IR function. JIR1 is compliant with Intel Front

Panel I/O Connectivity Design Guide.

Front USB Connectors: JUSB1, JUSB2 This mainboard provides two

standard USB2.0 pin headers that allow you to connect USB devices via

an external USB bracket.

Clear CMOS Jumper: JCMOS1 There is a CMOS RAM onboard that has

a power supply from external battery to keep the data of system

configuration. With the CMOS RAM, the system can automatically boot OS

every time it is turned on. If you want to clear the system configuration, set

the JCMOS1 (Clear CMOS Jumper ) to clear data.

PCI Express slots: PCIE16X1 , PCI_ E1 The PCI Express slots support

high-bandwidth, low pin count, and serial interconnect technology. You

can insert the expansion cards to meet your needs. When adding or

removing expansion cards, make sure that you unplug the power supply

first. PCI Express architecture provides a high performance I/O infrastruc-

ture for Desktop Platforms with transfer rates starting at 2.5 Giga transfers

per second over a PCI Express x1 lane for Gigabit Ethernet, TV Tuners,

1394 controllers, and general purpose I/O. Also, desktop platforms with PCI

Express Architecture will be designed to deliver highest performance in

video, graphics, multimedia and other sophisticated applications. Moreover,

PCI Express architecture provides a high performance graphics infrastruc-

ture for Desktop Platforms doubling the capability of existing AGP 8x

designs with transfer rates of 4.0 GB/s over a PCI Express x16 lane for

graphics controllers, while PCI Express x1 supports transfer rate of 250

MB/s.

PCI Slots The PCI slots allow you to insert the expansion cards to meet

your needs. When adding or removing expansion cards, make sure that

you unplug the power supply first.

E-10

MS-7151 ATX Mainboard

Central Processing Unit: CPU

The mainboard supports AMD

®

Athlon64 processor. The mainboard uses a

CPU socket called Socket-939 for easy CPU installation. When you are installing

the CPU, make sure the CPU has a heat sink and a cooling fan attached on

the top to prevent overheating. If you do not have the heat sink and cooling

fan, contact your dealer to purchase and install them before turning on the

computer.

For the latest information about CPU, please visit http://www.msi.com.tw/pro-

gram/products/mainboard/mbd/pro_mbd_cpu_support.php.

MSI Reminds You...

Overheating

Overheating will seriously damage the CPU and system, always make

sure the cooling fan can work properly to protect the CPU from

overheating.

Replacing the CPU

While replacing the CPU, always turn off the ATX power supply or

unplug the power supply’s power cord from grounded outlet first to

ensure the safety of CPU.

E-11

User’s Manual

CPU Installation Procedures for Socket 939

1.Please turn off the power and

unplug the power cord before

installing the CPU.

2.Pull the lever sideways away

from the socket. Make sure to

raise the lever up to a 90-

degree angle.

3.Look for the gold arrow of the

CPU. The gold arrow should

point as shown in the picture.

The CPU can only fit in the

correct orientation.

4.If the CPU is correctly installed,

the pins should be completely

embedded into the socket and

can not be seen. Please note

that any violation of the correct

installation procedures may

cause permanent damages to

your mainboard.

5. Press the CPU down firmly into

the socket and close the lever.

As the CPU is likely to move

while the lever is being closed,

always close the lever with

your fingers pressing tightly on

top of the CPU to make sure

the CPU is properly and

completely embedded into the

socket.

Open Lever

90 degree

Sliding

Plate

Gold arrow

Correct CPU placement

O

E-12

MS-7151 ATX Mainboard

Installing AMD Athlon64 CPU Cooler Set

When you are installing the CPU, make sure the CPU has a heat sink

and a cooling fan attached on the top to prevent overheating. If you do not

have the heat sink and cooling fan, contact your dealer to purchase and install

them before turning on the computer.

MSI Reminds You...

Mainboard photos shown in this section are for demonstration of the

cooler installation for Socket 939 CPUs only. The appearance of

your mainboard may vary depending on the model you purchase.

2.Locate the Fix Lever, Safety Hook

and the Fixed Bolt.

Lift up the intensive fixed lever.

1.Position the cooling set onto the

retention mechanism.

Hook one end of the clip to hook

first, and then press down the

other end of the clip to fasten the

cooling set on the top of the

retention mechanism.

3.Fasten down the lever.

4.Make sure the safety hook com-

pletely clasps the fixed bolt of the

retention mechanism.

Safety Hook

Fixed Bolt

Fixed Lever

5.Attach the CPU Fan cable to the CPU

fan connector on the mainboard.

La page est en cours de chargement...

MSI MS-7151 Le manuel du propriétaire

Ce manuel convient également à

MSI MS-7151 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents