MSI K8N NEO4 Le manuel du propriétaire

i

English / French / German

Version

G52-M7125X6

MS-7125 (v1.X) ATX Mainboard

K8N Neo4 Series

ii

Manual Rev: 1.0

Release Date: February 2005

FCC-B Radio Frequency Interference Statement

This equipment has been tested and found to comply with the limits for a class B

digital device, pursuant to part 15 of the FCC rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Operation

of this equipment in a residential area is likely to cause harmful interference, in which

case the user will be required to correct the interference at his own expense.

Notice 1

The changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

Notice 2

Shielded interface cables and A.C. power cord, if any, must be used in order to

comply with the emission limits.

VOIR LA NOTICE D’INSTALLATION AVANT DE RACCORDER AU RESEAU.

Micro-Star International

MS-7125

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation

iii

Copyright Notice

The material in this document is the intellectual property of MICRO-STAR

INTERNATIONAL. We take every care in the preparation of this document, but no

guarantee is given as to the correctness of its contents. Our products are under

continual improvement and we reserve the right to make changes without notice.

Trademarks

All trademarks are the properties of their respective owners.

AMD, Athlon™, Athlon™ XP, Thoroughbred™, and Duron™ are registered

trademarks of AMD Corporation.

Intel

®

and Pentium

®

are registered trademarks of Intel Corporation.

PS/2 and OS

®

/2 are registered trademarks of International Business Machines

Corporation.

Microsoft is a registered trademark of Microsoft Corporation. Windows

®

98/2000/NT/

XP are registered trademarks of Microsoft Corporation.

NVIDIA, the NVIDIA logo, DualNet, and nForce are registered trademarks or trade-

marks of NVIDIA Corporation in the United States and/or other countries.

Netware

®

is a registered trademark of Novell, Inc.

Award

®

is a registered trademark of Phoenix Technologies Ltd.

AMI

®

is a registered trademark of American Megatrends Inc.

Kensington and MicroSaver are registered trademarks of the Kensington Technology

Group.

PCMCIA and CardBus are registered trademarks of the Personal Computer Memory

Card International Association.

Revision History

Revision Revision History Date

V1.0 First release of PCB 1.0 December 2004

with nVIDIA nForce4 Ultra

V1.0 First release for PCB 1.0 February 2005

with nVIDIA nForce4 Ultra

For European manuals

iv

1. Always read the safety instructions carefully.

2. Keep this User’s Manual for future reference.

3. Keep this equipment away from humidity.

4. Lay this equipment on a reliable flat surface before setting it up.

5. The openings on the enclosure are for air convection hence protects the equip-

ment from overheating. Do not cover the openings.

6. Make sure the voltage of the power source and adjust properly 110/220V be-

fore connecting the equipment to the power inlet.

7. Place the power cord such a way that people can not step on it. Do not place

anything over the power cord.

8. Always Unplug the Power Cord before inserting any add-on card or module.

9. All cautions and warnings on the equipment should be noted.

10. Never pour any liquid into the opening that could damage or cause electrical

shock.

11. If any of the following situations arises, get the equipment checked by a service

personnel:

h The power cord or plug is damaged.

h Liquid has penetrated into the equipment.

h The equipment has been exposed to moisture.

h The equipment has not work well or you can not get it work according to

User’s Manual.

h The equipment has dropped and damaged.

h The equipment has obvious sign of breakage.

12. Do not leave this equipment in an environment unconditioned, storage

temperature above 60

0

C (140

0

F), it may damage the equipment.

Technical Support

If a problem arises with your system and no solution can be obtained from the user’s

manual, please contact your place of purchase or local distributor. Alternatively,

please try the following help resources for further guidance.

h Visit the MSI homepage & FAQ site for technical guide, BIOS updates, driver

updates, and other information: http://www.msi.com.tw & http://www.msi.

com.tw/program/service/faq/faq/esc_faq_list.php

h Contact our technical staff at: [email protected]

Safety Instructions

CAUTION: Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the

manufacturer.

v

CONTENTS

FCC-B Radio Frequency Interference Statement ........................................................ ii

Copyright Notice ........................................................................................................... iii

Revision History............................................................................................................ iii

Technical Support ........................................................................................................ iv

Safety Instructions ...................................................................................................... iv

English .................................................................................................................. E-1-1

1. Getting Started ........................................................................................... E-1-3

2. Hardware Setup ........................................................................................ E-2-1

3. BIOS Setup ................................................................................................. E-3-1

Français ....................................................................................................................F-1

Guide d’Utilisation ................................................................................................F-3

Deutsch ................................................................................................................... G-1

Benutzerhandbuch............................................................................................. G-3

E-1-1

Getting Started

K8N Neo4 Platinum

(MS-7125 v1.X)

ATX mainboard.

English

E-1-1

E-1-2

MS-7125 M-ATX Mainboard

E-1-3

Getting Started

Chapter 1. Getting

Started

Getting Started

Thank you for choosing the K8N Neo4 Platinum (MS-7125)

v1.X ATX mainboard. The K8N Neo4 Platinum mainboard is based

on nVIDIA

®

nForce™4 Ultra chipset for optimal system efficiency.

Designed to fit the advanced AMD

®

K8 Athlon 64 FX / Athlon 64

processor, the K8N Neo4 Platinum mainboard delivers a high per-

formance and professional desktop platform solution.

E-1-4

MS-7125 M-ATX Mainboard

Mainboard Specifications

CPU

h Supports Socket-939 for AMD K8 Athlon 64 FX / Athlon 64 (Socket939) processor

h Supports up to Athlon64 3500+, 3800+, or higher CPU

(For the latest information about CPU, please visit http://www.msi.com.tw/program/

products/mainboard/mbd/pro_mbd_cpu_support.php)

Chipset

h nVIDIA nForce4 Ultra

- HyperTransport link to the AMD Athlon 64/Athlon 64 FX CPU

- HyperTransport supporting speed up to 1GHz (2000MT/s)

- Supports PCI Express x16/x1/x2 interface

- Two independent SATA controllers, for four drives

- Dual Fast ATA-133 IDE controllers

- IEEE802.3 nVIDIA MAC for 1000BASE-T

Main Memory

h Supports dual channel, eight memory banks DDR 266/333/400, using four 184-

pin DDR DIMMs

h Supports a maximum memory size up to 4GB

h Supports 2.5v DDR SDRAM DIMM

(For the updated supporting memory modules, please visit http://www.msi.com.tw/

program/products/mainboard/mbd/pro_mbd_trp_list.php.)

Slots

h One PCI Express x16 slot (supports PCI Express Bus specification v1.0a

compliant)

h One PCI Express x1 slots (supports PCI Express Bus specification v1.0a

compliant)

h One PCI Express x4 slots (supports PCI Express x2 device only )

h Four 32-bit Master PCI Bus slots, includes one orange slot which is reserved as

a communication slot.

h Support 3.3V/5V PCI bus Interface

On-Board IDE

h An IDE controller on the nVIDIA

®

nForce4 Ultra chipset provides IDE HDD/CD-

ROM with PIO, Bus Master and Ultra DMA 66/100/133 operation modes

h Can connect up to 4 IDE devices

On-Board SATA

h NV RAID supports 4 SATA ports(SATA1-4). SATAII Transfer rate is up to

300MB/s.

h Silicon Image’s SATARAID5

TM

supports another 4 SATA ports(SATA5-8). SATA

Transfer rate is up to 150MB/s. (Optional)

E-1-5

Getting Started

USB Interface

h 10 USB ports

- Controlled by nForce4 Ultra chipset

- 4 ports in the rear I/O, 6 ports via the external bracket

NV RAID (Software)

h Supports up to 4 SATA and 4 ATA133 Hard drives

- RAID 0 or 1, 0+1, JBOD is supported

- RAID function available for PATA+SATA H/D drives

Silicon Image’s SATARAID5

TM

(Software) (Optional)

h RAID 0 or 1, RAID5, RAID10, and JBOD groups are supported

h Support up to 4 SATA devices connected to a single controller

Dual LAN (Optional)

h Supports dual LAN jacks

- 1st LAN supports 10/100/1000 Fast Ethernet by Marvell 88E1111

- 2nd LAN supports 10/100/1000 Fast Ethernet by Marvell 88E8053

IEEE 1394 (Optional)

h Supports up to two 1394 ports (rear panel x 1, pinheader x 1). Transfer rate is

up to 400Mbps

Audio

h Chip integrated by Realtek ALC850

- Direct Sound AC97 audio

- 7.1 Channel output

On-Board Peripherals

h On-Board Peripherals include:

- 1 floppy port supports 1 FDD with 360K, 720K, 1.2M, 1.44M and 2.88Mbytes

- 1 serial port

- 1 parallel port supporting SPP/EPP/ECP mode

- 1 Audio jack(5-in-1), coaxial/fiber SPDIF out

- 1 IrDA pinheader

- 1 CD-In pinheader

- 1 D-Bracket2 pinheader

- 2 IEEE1394 ports (Rear * 1 / Front * 1)(Optional)

- 10 USB1.1/2.0 ports (Rear * 4 / Front * 6)

E-1-6

MS-7125 M-ATX Mainboard

BIOS

h The mainboard BIOS provides “Plug & Play” BIOS which detects the peripheral

devices and expansion cards of the board automatically.

h The mainboard provides a Desktop Management Interface (DMI) function which

records your mainboard specifications.

h Supports boot from LAN, USB Device 1.1 & 2.0, and SATA HDD.

Dimension

h ATX Form Factor (30.4 cm X 24.4 cm)

Mounting

h 9 mounting holes

MSI Reminds You...

1. Now the nVidia nForce4 system driver is only available for Windows

2000 and Windows XP.

2. To create a bootable RAID volume for a Windows 2000 environment,

Microsoft’s Windows 2000 Service Pack 4 (SP4) is required. As the

end user cannot boot without SP4, a combination installation CD

must be created before attempting to install the operating system

onto the bootable RAID volume.

To create the combination installation CD, please refer to the follow-

ing website:

http://www.microsoft.com/windows2000/downloads/

servicepacks/sp4/HFdeploy.htm

E-1-7

Getting Started

K8N Neo4 Platinum (MS-7125 v1.X) ATX Mainboard

CPUFAN1

NBFAN1

S1W

SFAN2

JPW1

FDD1

SATA3

SATA5 SATA8

SATA6 SATA7

SATA4

SATA1

SATA2

JCD1

T:

M:

B:

Line-In

Line-Out

Mic

T: RS -Ou t

M:CS

B:SPDIF Out

-Out

T: LAN jack

B: USB ports

(Optional)

T: LAN jack

B: USB ports

(Optional)

Winbond

W83627THF

Silicon Image

SATALink

Sil3114CT176

(Optional)

VIA

VT6307

(Optional)

88E1111-RCJ

(Optional)

BATT

+

DIMM 1

SFAN1

DIMM 3

DIMM 2

DIMM 4

ATX1

PCI Slot 3

PCI Slot 2

PCI Slot 1

PCI _E3

PCI _E2

PCI _E1

IDE 2

IDE 1

JFP1

JDB1

JFP2

JIR1JIR1

JCI1

JLPC1

JAUD1

JUSB2

JUSB3

JUSB1

J1394_1

(Optional)

Top : Parallel Port

Bottom:

COM Port

1394 Port (Optional)

SPDIF OUT

Top : mouse

Bottom: keyboard

MSI

CoreCell

BIOS

Codec

PCI Slot 4

88E8053-NNC

(Optional)

NForce4

Ultra

(

Optional

)

Mainboard Layout

E-1-8

MS-7125 M-ATX Mainboard

Packing Contents

Power Cable

SATA Cable (Optional)

User’s Guide Test Report

D-Bracket 2 (Optional)

MSI motherboard

MSI Driver/Utility CD

SATA RAID Driver

Diskette

Round Cable of

IDE Devices

Back IO Shield

Quick Guide

1394 Cable (Optional)

Round Cable of

Floppy Disk

Hardware Setup

E-2-1

Chapter 2. Hardware Setup

This chapter tells you how to install the CPU, memory modules,

and expansion cards, as well as how to setup the jumpers on the

mainboard. Also, it provides the instructions on connecting the periph-

eral devices, such as the mouse, keyboard, etc.

While doing the installation, be careful in holding the compo-

nents and follow the installation procedures.

Hardware Setup

MS-7125 M-ATX Mainboard

E-2-2

Quick Components Guide

DDR DIMMs, p.2-7

JDB1, p.2-22

JFP1, p.2-19

Back Panel

I/O, p.2-12

JPW1, p.2-10

IDE1/2, p.2-17

ATX1, p.2-10

JFP2, p.2-19

PCI_E2, p.2-26

PCI Slots 1~4,

p.2-26

JUSB1~3, p.2-19

SATA1~4,

p.2-18

J1394_1, p.2-21

(Optional)

NBFAN1,

p.2-16

CPUFAN1, p.2-16

JAUD1, p.2-20

SW1, p.2-25

FDD1, p.2-16

SFAN1, p.2-16

JCD1, p.2-18

JCI1, p.2-7

JIR1, p.2-20

SFAN2,

p.2-16

SATA5~8,

p.2-18

PCI_E1, p.2-26

PCI_E3, p.2-26

CPU, p.2-3

Hardware Setup

E-2-3

Central Processing Unit: CPU

The mainboard supports AMD

®

Athlon64 processor. The mainboard uses a CPU

socket called Socket-939 for easy CPU installation. When you are installing the CPU,

make sure the CPU has a heat sink and a cooling fan attached on the top to

prevent overheating. If you do not have the heat sink and cooling fan, contact your

dealer to purchase and install them before turning on the computer.

For the latest information about CPU, please visit http://www.msi.com.tw/program/

products/mainboard/mbd/pro_mbd_cpu_support.php.

MSI Reminds You...

Overheating

Overheating will seriously damage the CPU and system, always make

sure the cooling fan can work properly to protect the CPU from

overheating.

Replacing the CPU

While replacing the CPU, always turn off the ATX power supply or

unplug the power supply’s power cord from grounded outlet first to

ensure the safety of CPU.

Overclocking

This motherboard is designed to support overclocking. However, please

make sure your components are able to tolerate such abnormal setting,

while doing overclocking. Any attempt to operate beyond product speci-

fications is not recommended. We do not guarantee the damages

or risks caused by inadequate operation or beyond product

specifications.

MS-7125 M-ATX Mainboard

E-2-4

CPU Installation Procedures for Socket 939

1. Please turn off the power and

unplug the power cord before

installing the CPU.

2. Pull the lever sideways away

from the socket. Make sure to

raise the lever up to a 90-de-

gree angle.

3. Look for the gold arrow on the

CPU. The gold arrow should point

as shown in the picture. The CPU

can only fit in the correct

orientation.

4. If the CPU is correctly installed,

the pins should be completely

embedded into the socket and

can not be seen. Please note

that any violation of the correct

installation procedures may

cause permanent damages to

your mainboard.

5. Press the CPU down firmly into

the socket and close the lever.

As the CPU is likely to move while

the lever is being closed, al-

ways close the lever with your

fingers pressing tightly on top of

the CPU to make sure the CPU is

properly and completely embed-

ded into the socket.

Open Lever

90 degree

Sliding

Plate

Gold arrow

Correct CPU placement

O

Hardware Setup

E-2-5

Installing AMD Athlon64 CPU Cooler Set

When you are installing the CPU, make sure the CPU has a heat sink and a

cooling fan attached on the top to prevent overheating. If you do not have the

heat sink and cooling fan, contact your dealer to purchase and install them before

turning on the computer.

1. Detach the shield of the backplate’s

paster.

2. Turn over the mainboard, and install

the backplate to the proper position.

3. Turn over the mainboard again, and

place the mainboard on the flat

surface.

Locate the two screw holes of the

mainboard.

4. Align the retention mechanism and

the backplate.

Fix the retention mechanism and the

backplate with two screws.

retention mechanism

MS-7125 M-ATX Mainboard

E-2-6

6. Locate the Fix Lever, Safety Hook

and the Fixed Bolt.

Lift up the intensive fixed lever.

5. Position the cooling set onto the re-

tention mechanism.

Hook one end of the clip to hook first,

and then press down the other end

of the clip to fasten the cooling set

on the top of the retention mechanism.

7. Fasten down the lever.

8. Make sure the safety hook completely

clasps the fixed bolt of the retention

mechanism.

Safety Hook

Fixed Bolt

Fixed Lever

9. Attach the CPU Fan cable to the CPU

fan connector on the mainboard.

MSI Reminds You...

While disconnecting the Safety Hook from the fixed bolt, it is neces-

sary to keep an eye on your fingers, because once the Safety Hook is

disconnected from the fixed bolt, the fixed lever will spring back instantly.

Hardware Setup

E-2-7

Memory

DIMM1~4

(from left to right)

The mainboard provides 4 slots for 184-pin DDR SDRAM DIMM (Double In-Line Memory

Module) modules and supports the memory size up to 4GB. You can install DDR266/

333/400 modules on the DDR DIMM slots (DDR 1~4).

For the updated supporting memory modules, please visit http://www.msi.com.tw/

program/products/mainboard/mbd/pro_mbd_trp_list.php.

DIMM Module Combination

Install at least one DIMM module on the slots. Each DIMM slot supports up to a maximum

size of 1GB. Users can install either single- or double-sided modules to meet their

own needs. Please note that each DIMM can work respectively for single-

channel DDR, but there are some rules while using dual-channel DDR (Please

refer to the suggested DDR population table below). Users may install memory modules

of different type and density on different-channel DDR DIMMs. However, the same

type and density memory modules are necessary while using dual-channel DDR,

or instability may happen. Please refer to the following table for detailed dual-channel

DDR. Other combination not listed below will function as single-channel DDR.

Introduction to DDR SDRAM

DDR (Double Data Rate) SDRAM is similar to conventional SDRAM, but doubles the

rate by transferring data twice per cycle. It uses 2.5 volts as opposed to 3.3 volts

used in SDR SDRAM, and requires 184-pin DIMM modules rather than 168-pin DIMM

modules used by SDR SDRAM. High memory bandwidth makes DDR an ideal solution

for high performance PC, workstations and servers.

La page charge ...

MSI K8N NEO4 Le manuel du propriétaire

Ce manuel convient également à

MSI K8N NEO4 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents