Hach TU5300 sc Basic User Manual

DOC023.97.90501

TU5300 sc/TU5400 sc

09/2019, Edition 5

Basic User Manual

Manuel d'utilisation simplifié

Manual básico del usuario

Manual Básico do Usuário

基本用户手册

基本取扱説明書

คู่มือผู้ใช้เบื้องต้น

기본 사용 설명서

基本使用手冊

Table of Contents

English..............................................................................................................................3

Français......................................................................................................................... 31

Español.......................................................................................................................... 62

Português...................................................................................................................... 92

中文............................................................................................................................... 123

日本語........................................................................................................................... 150

ไทย.................................................................................................................................. 179

한글............................................................................................................................... 208

中文............................................................................................................................... 237

2

Table of Contents

1 Additional information on page 3

2 Specifications on page 3

3 General information on page 5

4 Installation on page 10

5 User navigation on page 21

6 Operation on page 21

7 Calibration on page 21

8 Verification on page 21

9 Maintenance on page 22

10 Troubleshooting on page 29

Section 1 Additional information

An expanded user manual is available on the manufacturer's website. Videos on how to install,

operate and do maintenance and troubleshooting on the TU5300 sc and the TU5400 sc turbidimeters

are available on the TU5 Series Turbidimeters playlist at

http://www.youtube.com/user/hachcompany.

Section 2 Specifications

Specifications are subject to change without notice.

Specification Details

Measurement method Nephelometry with scattered light collected at a 90-degree angle to the incident light

and 360 degrees around the sample vial

Primary compliance

method

EPA approved Hach Method 10258

1

Enclosure Material: ASA Luran S 777K / RAL7000, TPE RESIN Elastocon

®

STK40,

Thermoplastic Elastomer TPS-SEBS (60 Shore) and stainless steel

IP rating Electronic compartment IP55; process head/Automatic Cleaning Module attached to

the instrument and all of the other functional units IP65

2

Dimensions (W x D x H) 268 x 249 x 190 mm (10.6 x 9.8 x 7.5 in.)

Weight Instrument with the process head: 2.7 kg (6.0 lb); Instrument with the optional

automatic cleaning module: 5.0 kg (11.0 lb)

Power requirements 12 VDC, 14 VA supplied by the SC controller

Protection class III

Pollution degree 2

Installation category II

Mounting Indoor on a wall

Operating temperature 0 to 50 °C (32 to 122 °F)

Storage temperature –40 to 60 °C (–40 to 140 °F)

Humidity 5 to 95% relative humidity, non-condensing

Sensor cable length TU5x00 sc without Automatic Cleaning Module or flow sensor: 50 m (164 ft);

TU5x00 sc with Automatic Cleaning Module: 10 m (33 ft)

Laser Class 2 laser product: Contains a non user-serviceable class 2 laser.

Optical light source 650 nm, maximum 0.43 mW

Fittings Sample inlet and outlet: ¼-in. OD tubing (optional tubing adapter, ¼ in. to 6 mm)

1

http://www.hach.com

2

Water drops, puddles or runlets that will not damage the instrument may be in the inner of the

enclosure.

English 3

Specification Details

Tubing requirements Polyethylene, polyamide or polyurethane tubing. Calibrated ¼ in. OD,

+0.03 or –0.1 mm (+0.001 or –0.004 in.)

Measurement units TU5300 sc: NTU, FNU, TE/F, EBC or FTU; TU5400 sc: NTU, mNTU

3

, FNU, mFNU,

TE/F, EBC, FTU or mFTU.

Range 0 to 700 NTU, FNU, TE/F and FTU; 0 to 175 EBC

Method detection limit 0.0001 NTU at 25 °C (77 °F)

Response time T90 < 30 seconds at 100 mL/min

Signal averaging TU5300 sc: 30–90 seconds

TU5400 sc: 1–90 seconds

Accuracy ± 2% or ± 0.01 NTU (the larger value) from 0 to 40 NTU

± 10% of reading from 40 to 700 NTU based on Formazin primary standard at 25 °C

(77 °F)

Linearity Better than 1% for 0 to 40 NTU based on Formazin primary standard at 25 °C

(77 °F).

Repeatability TU5300 sc: 0.002 NTU or 1% (the larger value) at 25 °C (77 °F) ( > 0.025 NTU

range);

TU5400 sc: 0.0006 NTU or 1% (the larger value) at 25 °C (77 °F) ( > 0.025 NTU

range)

Stray light < 0.01 NTU

Resolution 0.0001 NTU (0.0001 to 0.9999/1.000 to 9.999/10.00 to 99.99/100.0 to 700 NTU)

Default: TU5300 sc: 0.001 NTU and TU5400 sc: 0.0001 NTU

Air bubble compensation Physical, mathematical

Sample requirements Temperature: 2 to 60 °C (35.6 to 140 °F)

Conductivity: 3000 µS/cm maximum at 25 °C (77 °F)

Flow rate

4

: 100 to 1000 mL/min; optimal flow rate: 200 to 500 mL/min

Pressure: 6 bar (87 psi) maximum compared to air, 2 to 40 °C (35.6 to 104 °F)

sample; 3 bar (43.5 psi) maximum compared to air, 40 to 60 °C (104 to 140 °F)

sample

Calibration options StablCal

®

or Formazin: 1-point calibration (20 NTU) for 0 to 40 NTU measurement

range, 2-point calibration (20 and 600 NTU) for 0 to 700 NTU (full) measurement

range or 2- to 6-point custom calibration for a measurement range of 0 NTU to the

highest calibration point.

Verification options Glass verification rod (solid secondary standard) ≤ 0.1 NTU, StablCal or Formazin

Verification (RFID or

Link2SC

®

)

Verification of the measurement value by comparison of the process and lab

measurements with RFID or Link2SC.

Certifications CE compliant; US FDA accession number: 1420493-xxx. This product complies with

IEC/EN 60825-1 and to 21 CFR 1040.10 in accordance with Laser Notice No. 50.

Australian RCM.

Warranty 1 year (EU: 2 years)

3

1 mNTU = 0.001 NTU

4

For the best results, operate the instrument at a flow rate of 200 mL/min when the maximum

particle size is 20 µm. For larger particles (150 µm maximum), the best flow rate is 350 to

500 mL/min.

4 English

Section 3 General information

In no event will the manufacturer be liable for direct, indirect, special, incidental or consequential

damages resulting from any defect or omission in this manual. The manufacturer reserves the right to

make changes in this manual and the products it describes at any time, without notice or obligation.

Revised editions are found on the manufacturer’s website.

3.1 Safety information

N O T I C E

The manufacturer is not responsible for any damages due to misapplication or misuse of this product including,

without limitation, direct, incidental and consequential damages, and disclaims such damages to the full extent

permitted under applicable law. The user is solely responsible to identify critical application risks and install

appropriate mechanisms to protect processes during a possible equipment malfunction.

Please read this entire manual before unpacking, setting up or operating this equipment. Pay

attention to all danger and caution statements. Failure to do so could result in serious injury to the

operator or damage to the equipment.

Make sure that the protection provided by this equipment is not impaired. Do not use or install this

equipment in any manner other than that specified in this manual.

3.1.1 Use of hazard information

D A N G E R

Indicates a potentially or imminently hazardous situation which, if not avoided, will result in death or serious injury.

W A R N I N G

Indicates a potentially or imminently hazardous situation which, if not avoided, could result in death or serious

injury.

C A U T I O N

Indicates a potentially hazardous situation that may result in minor or moderate injury.

N O T I C E

Indicates a situation which, if not avoided, may cause damage to the instrument. Information that requires special

emphasis.

3.1.2 Precautionary labels

Read all labels and tags attached to the instrument. Personal injury or damage to the instrument

could occur if not observed. A symbol on the instrument is referenced in the manual with a

precautionary statement.

Electrical equipment marked with this symbol may not be disposed of in European domestic or

public disposal systems. Return old or end-of-life equipment to the manufacturer for disposal at no

charge to the user.

This symbol, if noted on the instrument, references the instruction manual for operation and/or safety

information.

This symbol indicates the need for protective eye wear.

This symbol indicates a laser device is used in the equipment.

English 5

This symbol indicates that the marked item can be hot and should not be touched without care.

This symbol identifies a risk of chemical harm and indicates that only individuals qualified and

trained to work with chemicals should handle chemicals or perform maintenance on chemical

delivery systems associated with the equipment.

This symbol indicates radio waves.

3.1.3 Class 2 laser product

D A N G E R

Personal injury hazard. Never remove covers from the instrument. This is a laser-based instrument

and the user risks injury if exposed to the laser.

Class 2 laser product, IEC60825-1:2014, 650 nm, maximum 0.43 mW

Location: Rear of the instrument.

Conforms to U.S. regulations 21 CFR 1040.10 and 1040.11 in accordance with

Laser Notice No. 50.

Location: Rear of the instrument.

Caution—Class 2 laser radiation when the lid is open. Do not look into the laser

beam.

Location: Top of the vial compartment.

This instrument is a Class 2 Laser product. There is only visible laser radiation when the instrument

is defective and when the instrument lid is open. This product complies with EN 61010-1, "Safety

Requirements for Electrical Equipment for Measurement, Control and Laboratory Use" and with

IEC/EN 60825-1, "Safety of Laser Products" and with 21 CFR 1040.10 in accordance with Laser

Notice No. 50. Refer to the labels on the instrument that supply laser information.

3.1.4 RFID module

Instruments with the optional RFID module receive and transmit information and data. The RFID

module operates with a frequency of 13.56 MHz.

RFID technology is a radio application. Radio applications are subject to national conditions of

authorization. The use of instruments with the optional RFID module is currently permitted in the

regions that follow:

EU (European Union) countries, EFTA (European Free Trade Association) countries, Turkey, Serbia,

Macedonia, Australia, Canada, US, Chile, Ecuador, Venezuela, Mexico, Brazil, South Africa, India,

Singapore, Argentina, Columbia, Peru and Panama

6

English

The use of instruments with the optional RFID module outside of the above-mentioned regions can

violate national laws. The manufacturer reserves the right also to get authorization in other countries.

In case of doubt, contact the manufacturer.

3.1.4.1 Safety information for RFID modules

W A R N I N G

Multiple hazards. Do not disassemble the instrument for maintenance. If the internal components

must be cleaned or repaired, contact the manufacturer.

W A R N I N G

Electromagnetic radiation hazard. Do not use the instrument in dangerous environments.

N O T I C E

This instrument is sensitive to electromagnetic and electromechanical interference. These interferences can have

an effect on the analysis performance of this instrument. Do not put this instrument near equipment that can

cause interference.

Obey the safety information that follows to operate the instrument in accordance with local, regional

and national requirements.

• Do not operate the instrument in hospitals and equivalent establishments or near medical

equipment, such as pace makers or hearing aids.

• Do not operate the instrument near highly flammable substances, such as fuels, highly flammable

chemicals and explosives.

• Do not operate the instrument near combustible gases, vapors or dust.

• Keep the instrument away from strong vibration or shock.

• The instrument can cause interference in immediate proximity to televisions, radios and

computers.

• The warranty does not cover improper use or wear.

3.1.4.2 FCC conformance for RFID

This instrument may contain a registered radio frequency identification device (RFID). Refer to

Table 1 for the Federal Communications Commission (FCC) registration information.

Table 1 Registration information

Parameter Value

FCC identification number (FCC ID) YCB-ZBA987

IC 5879A-ZBA987

Frequency 13.56 MHz

3.1.5 Certification

C A U T I O N

This equipment is not intended for use in residential environments and may not provide adequate protection to

radio reception in such environments.

Canadian Radio Interference-Causing Equipment Regulation, ICES-003, Class A:

Supporting test records reside with the manufacturer.

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing

Equipment Regulations.

English

7

Cet appareil numérique de classe A répond à toutes les exigences de la réglementation canadienne

sur les équipements provoquant des interférences.

FCC Part 15, Class "A" Limits

Supporting test records reside with the manufacturer. The device complies with Part 15 of the FCC

Rules. Operation is subject to the following conditions:

1. The equipment may not cause harmful interference.

2. The equipment must accept any interference received, including interference that may cause

undesired operation.

Changes or modifications to this equipment not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment. This equipment has been tested

and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference, in which case the user will be required to

correct the interference at their expense. The following techniques can be used to reduce

interference problems:

1. Disconnect the equipment from its power source to verify that it is or is not the source of the

interference.

2. If the equipment is connected to the same outlet as the device experiencing interference, connect

the equipment to a different outlet.

3. Move the equipment away from the device receiving the interference.

4. Reposition the receiving antenna for the device receiving the interference.

5. Try combinations of the above.

3.2 Product overview

D A N G E R

Chemical or biological hazards. If this instrument is used to monitor a treatment process and/or

chemical feed system for which there are regulatory limits and monitoring requirements related to

public health, public safety, food or beverage manufacture or processing, it is the responsibility of the

user of this instrument to know and abide by any applicable regulation and to have sufficient and

appropriate mechanisms in place for compliance with applicable regulations in the event of

malfunction of the instrument.

The TU5300 sc and the TU5400 sc turbidimeters are used with an SC controller to measure low-

range turbidity mostly in finished drinking water applications. Refer to Figure 1.

The TU5300 sc and the TU5400 sc turbidimeters measure scattered light at an angle of 90° in a 360°

radius around the axis of the incident light beam.

An optional RFID module and an automatic system check option are available

5

. The RFID module is

shown in Figure 1. The RFID module lets process and laboratory turbidity measurements be easily

compared. A description of the automatic system check option is given in the expanded user manual

on the manufacturer's website.

PROGNOSYS predictive diagnostic software is available for the TU5300 sc and TU5400 sc

turbidimeters. To use PROGNOSYS, connect the turbidimeter to an SC controller with

PROGNOSYS.

Videos on how to install, operate and do maintenance and troubleshooting on the TU5300 sc and the

TU5400 sc turbidimeters are available on the TU5 Series Turbidimeters playlist at

http://www.youtube.com/user/hachcompany.

For the accessories, refer to the expanded user manual on the manufacturer's website.

5

The RFID module and automatic system check option is only available at the time of purchase.

8 English

Figure 1 Product overview

1 Programmable button 9 Vial compartment

2 Status indicator light

6

10 Overflow drain

3 RFID module indicator (optional) 11 Process head (open)

4 Cleaning lid screws (3x) 12 Process head (closed)

5 Cleaning lid 13 Channels for cables

6 Process head 14 Extension connector for accessories

7 Sample inlet 15 Sensor cable

8 Sample outlet

3.3 Product components

Make sure that all components have been received. Refer to Figure 2. If any items are missing or

damaged, contact the manufacturer or a sales representative immediately.

6

Shows the instrument status. Refer to the expanded user manual on the manufacturer's website

for more information.

English 9

Figure 2 Product components

1 TU5300 sc or TU5400 sc 6 Cleaning lid screws and washers for hot water

applications

2 Wall mount bracket (two tubing clips on bracket) 7 Vial replacement tool

3 Tubing clips 8 Flow regulator

4 Tubing clip screws, 2.2 x 6 mm 9 Service bracket

5 Mounting screws, 4 x 16 mm 10 Desiccant cartridge

Section 4 Installation

C A U T I O N

Multiple hazards. Only qualified personnel must conduct the tasks described in this section of the

document.

4.1 Installation guidelines

N O T I C E

Make sure that there is a floor drain near the instrument. Examine the instrument daily for leaks.

This instrument is rated for an altitude of 3100 m (10,710 ft) maximum. Use of this instrument at an

altitude higher than 3100 m can slightly increase the potential for the electrical insulation to break

down, which can result in an electric shock hazard. The manufacturer recommends that users with

concerns contact technical support.

4.2 Installation overview

Figure 3 shows the installation overview with no accessories and the clearances necessary. Refer to

the expanded manual on the manufacturer's website for the system overview with all of the

accessories.

10

English

Figure 3 Installation overview with no accessories

1 Service bracket 5 Sample inlet

2 Process head 6 Sample outlet

3 SC controller 7 TU5300 sc or TU5400 sc

4 Flow regulator

4.3 Wall mount

Install the instrument on a wall in a vertical position. Install the instrument so that it is level.

4.3.1 Install with the wall mount bracket

Refer to the illustrated steps that follow to install the instrument on a wall with the wall mount bracket.

The mounting hardware to install the wall mount bracket on a wall is supplied by the user.

If a 1720D, 1720E, or FT660 instrument is replaced, remove the instrument from the wall. Then do

steps 2 to 4 of the illustrated steps that follow to install the instrument on the existing hardware.

Note: When the accessories are used, the installation location of the tubing clips is different. Refer to the

documentation supplied with the accessories for tubing clip installation.

English

11

12 English

4.3.2 Install directly on a wall

As an alternative, refer to the illustrated steps that follow to install the instrument directly on a wall.

The mounting hardware is supplied by the user. Remove the thin, plastic film from the mounting

holes on the back of the instrument.

4.4 Install the desiccant cartridge

N O T I C E

Make sure that the desiccant cartridge is installed or damage to the instrument will occur.

For initial installation, complete the steps below. For replacement, refer to the documentation

supplied with the desiccant cartridge.

1. Look at the install by date on the packaging. Refer to Figure 4. Do not use if the current date is

past the install by date.

2. Make sure that the indicator on the new desiccant cartridge is light blue. Refer to Figure 4.

3. Install the new desiccant cartridge. Refer to the illustrated steps that follow.

English

13

Figure 4 Examine the desiccant cartridge

1 Install by date (mm.yyyy =

month and year)

2 Indicator (light blue = not

expired, white = expired)

3 Transport safety protection

14 English

English 15

4.5 Replace the cleaning lid screws

N O T I C E

Do not overtighten the screws or breakage will occur. Hand tighten the screws.

If the sample temperature is 40 to 60 °C (104 to 140 °F), the cleaning lid screws will become hot. To

prevent burns, replace the standard cleaning lid screws with the cleaning lid screws and washers for

hot water. Refer to Figure 1 on page 9 for the location of the cleaning lid screws.

4.6 Install the service bracket

The service bracket holds the process head (or the optional automatic cleaning module) when it is

not installed on the instrument.

Refer to Installation overview on page 10 to install the service bracket the correct distance from the

instrument. Refer to the illustrated steps that follow to install the service bracket.

4.7 Install the flow sensor (optional)

The optional flow sensor identifies if the sample flow is within specifications. A warning shows on the

controller display and the status indicator light when a no flow, low flow or high flow warning occurs.

Install the optional flow sensor. Refer to the documentation supplied with the optional flow sensor.

4.8 Install the automatic cleaning module (optional)

The automatic cleaning module cleans the inside of the process vial at a selected time interval. Install

the optional automatic cleaning module. Refer to the documentation supplied with the automatic

cleaning module.

4.9 Connect to an SC controller

C A U T I O N

Personal injury hazard. Do not look into the vial compartment when the instrument is connected to

power.

16 English

1. Get the latest software version from www.hach.com. Install the latest software version on the SC

controller before the instrument is connected to the SC controller.

Refer to the software installation instructions supplied in the box or supplied in the software

download for the SC controller.

2. Remove power to the SC controller.

3. Connect the sensor cable to the quick-connect fitting of the SC controller. Refer to Figure 5. Keep

the connector cap for later use.

4. Supply power to the SC controller.

The SC controller looks for the instrument.

5. When the SC controller finds the instrument, push enter.

On the main screen, the controller shows the turbidity value measured by the turbidimeter.

Figure 5 Connect the sensor cable to the SC controller

4.10 Plumbing

4.10.1 Plumb the instrument

W A R N I N G

Explosion hazard. Make sure that the drain tube is free of all obstructions. If the drain tube has a

blockage or is pinched or bent, high pressure can build up in the instrument.

W A R N I N G

Personal injury hazard. The sample line contains water under high water pressure that can burn skin

if hot. Qualified personnel must remove the water pressure and wear personal protective equipment

during this procedure.

N O T I C E

Do not let water get in the vial compartment or instrument damage will occur. Before the process head is installed

on the instrument, make sure that there are no water leaks. Make sure that all tubing is fully seated. Make sure

that the vial nut is tight. The full water pressure should be on the system, the water flow is on and no water leak

on the glass vial is seen.

English 17

N O T I C E

Hold the automatic cleaning module vertically when it is installed on the instrument or the vial can break. If the vial

breaks, water will get in the vial compartment and instrument damage will occur.

N O T I C E

Before the instrument is plumbed, make sure that the desiccant cartridge and vial are installed.

N O T I C E

Based on the environmental conditions, is necessary to wait a minimum of 15 minutes to let the system become

stable.

Items supplied by the user:

• Flow shutoff valve

• Tubing

7

• Tubing cutter

1. Plumb the instrument. Refer to the illustrated steps that follow and Figure 6.

Note: To plumb the instrument with accessories, refer to the documentation supplied with the accessories.

Note: Use the opaque tubing accessory supplied from HACH accessory to prevent the bacteria growth.

Figure 6 Plumbing overview – no accessories

1 Service bracket 4 Flow regulator

2 Sample inlet 5 Flow shutoff valve

3 Sample outlet

7

Refer to Specifications on page 3 for the tubing requirements.

18 English

English 19

4.10.2 Set the flow rate

1. Measure the flow with the flow regulator fully open. Make sure that the flow is in the middle of the

flow specification. Refer to Specifications on page 3.

2. Slowly close the flow regulator until the flow decreases by 20 to 30%.

Note: The flow regulator causes back pressure in the tubing and decreases the quantity of bubbles that can

form in the vial.

20

English

La page charge ...

Hach TU5300 sc Basic User Manual

Ce manuel convient également à

Hach TU5300 sc Basic User Manual

dans d''autres langues

Documents connexes

Autres documents