Teeter 700ia Assembly Instructions

Marque: Teeter

Modèle: 700ia

Taper: Assembly Instructions

700ia

Inversion Table

To download and print Teeter’s 700ia instructions, visit the product support page at teeter.com.

* Speciﬁcations may vary from this image and

are subject to change without notice.

Assembly Instructions

YEAR

NEW!

Follow along with

your smartphone

to make assembly

even easier!

For gravity-assisted stretching and decompression

Owner’s Manual (attached to the equipment)

Important Safety Instructions ...................... 1

User Settings ...................................... 2

Prepare to Invert................................3 – 4

Inverting .......................................4 – 5

Storage and Maintenance.......................... 5

Get the Most out of Your Teeter .................... 6

Assembly Instructions

Important Safety Instructions ...................... 1

Items for Assembly ................................ 2

Understanding Your Inversion Table................ 3

Safety Warning Labels and Product Speciﬁcations .. 4

Before Beginning Assembly........................ 5

Assembly Steps ...............................6 – 11

Misassembly Check............................... 12

Before Inverting ..................................13

Warranty Terms and Registration .................15

Congratulations on your purchase of a Teeter 700ia Inversion Table! In order to utilize this product to its fullest extent, it is critical

that you follow the assembly instructions, read and fully understand the Owner’s Manual attached to the equipment, and review

the Getting Started DVD prior to using your new Teeter Inversion Table.

Teeter Decompression Devices are multiple user, reusable devices for home use, intended to provide traction to the spine while

stretching the para-spinal muscle and soft tissues. The devices provide non-powered traction and are meant for use by adults.

Use of Health Canada Approved Teeter Decompression Devices is indicated for the following conditions: back pain, muscle tension,

degenerative disc disease, spinal degenerative joint disease, spinal stenosis, herniated disc, spinal curvature due to tight muscles,

sciatica, muscle spasm, and facet syndrome.

To register your product warranty, go to teeter.com/Support/Warranty-Registration

If you have any questions concerning assembly or if any parts are missing, DO NOT RETURN THE ITEM TO THE STORE

OR CONTACT THE RETAILER. Our dedicated customer service experts can help! Contact Teeter Customer Service

at 800.847.0143, or via online forms or Live Chat at teeter.com.

Get more from your inversion sessions by downloading the TeeterLink™ app to your phone to track

usage and pain levels, get reminders and customized guidance, access support, and more! Scan the

code or search TeeterLink in your app store to get started!

WARNING

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING THE INVERSION TABLE

SAVE THESE INSTRUCTIONS

BEFORE YOU BEGIN: Review all steps before beginning assembly and read all precautions before using the inversion table.

Carefully adhere to the Assembly Instructions and Owner’s Manual to help ensure safety and product integrity.

FAILURE TO FOLLOW INSTRUCTIONS AND WARNINGS COULD RESULT IN SERIOUS INJURY OR DEATH.

To reduce the risk of injury:

• Read and understand all the instructions, review all other accompanying documents, and inspect the equipment before using the

inversion table. It is your responsibility to familiarize yourself with the proper use of this equipment and the inherent risks of inversion

if these instructions are not followed, such as falling on your head or neck, pinching, entrapment, equipment failure, or aggravating a

pre-existing medical condition. It is the responsibility of the owner to ensure that all users of the product are fully informed about the

proper use of the equipment and all safety precautions.

• DO NOT use until approved by a licensed physician. Inversion is contraindicated in any medical or health condition that may be

made more severe by an elevation of blood pressure, intracranial pressure or mechanical stress of the inverted position, or that may

impact your ability to operate the equipment. This may include injury or illness, but also the side effects of any drug or supplement

(prescribed or over-the-counter). Speciﬁc conditions may include, but not be limited to:

· Any condition, neurological or otherwise, which results in unexplained tingling, weakness or neuropathy, seizure, sleep disorder,

lightheadedness, dizziness, disorientation, or fatigue, or impacts strength, mobility, alertness, or cognitive ability;

· Any brain condition, such as trauma, history of intracranial bleed, history or risk of TIA or stroke, or severe headaches;

· Any condition of the heart or circulatory system, such as high blood pressure, hypertension, increased risk of stroke, or use of

anticoagulants (including high doses of aspirin);

· Any bone, skeletal or spinal cord condition or injury, such as signiﬁcant spinal curvature, acutely swollen joints, osteoporosis,

fractures, dislocations, medullary pins or surgically implanted orthopedic supports;

· Any eye, ear, nasal or balance condition, such as trauma, history of retinal detachment, glaucoma, optic hypertension, chronic

sinusitis, middle or inner ear disease, motion sickness, or vertigo;

· Any digestive or internal condition, such as severe acid reﬂux, hiatal or other hernia, gallbladder or kidney disease;

· Any condition for which exercise is speciﬁcally directed, limited or prohibited by a physician, such as pregnancy, obesity,

or recent surgery.

• ALWAYS be certain the Ankle Lock System is properly adjusted and fully engaged, and that your ankles are secure before using

the equipment. HEAR, FEEL, SEE and TEST that the Ankle Lock System is snug, close-ﬁtting and secure EVERY TIME you use

the equipment.

• ALWAYS wear securely tied lace-up shoes with a ﬂat sole, such as a normal tennis-style shoe.

• DO NOT wear any footwear that could interfere with securing the Ankle Lock System, such as shoes with thick soles, boots, high-tops

or any shoe that extends above the anklebone.

• DO NOT use the inversion table until it is adjusted properly for your height and body weight. Improper settings can cause rapid

inversion or make returning upright dicult. New users, and users who are physically or mentally compromised, will require the

assistance of a spotter. Make sure the equipment is set to your unique user settings prior to each use.

• DO NOT sit up or raise head to return upright. Instead, bend knees and slide your body to the foot-end of the inversion table to change

weight distribution. If locked out in full inversion, follow the instructions for releasing from the locked position before returning upright.

• DO NOT continue using the equipment if you feel pain or become light-headed or dizzy while inverting. Immediately return to the

upright position for recovery and eventual dismount.

• DO NOT use if you are over 6 ft 6 in (198 cm) or over 300 lbs. (136 kg). Structural failure could occur or head/neck may impact the

ﬂoor during inversion.

• DO NOT allow children to use this machine. Keep children, bystanders, and pets away from machine while in use. The inversion table

is not intended for use by persons with reduced physical, sensory or mental capabilities, unless they are given supervision and

instruction concerning use of the machine by a person responsible for their safety.

• DO NOT store the inversion table upright if children are present. Fold and lay the table on the ﬂoor. DO NOT store outdoors.

• DO NOT use aggressive movements, or use weights, elastic bands, any other exercise or stretching device or non-Teeter® attachments

while on the inversion table. Use the inversion table only for its intended use as described in this manual.

• DO NOT drop or insert any object into any opening. Keep body parts, hair, loose clothing and jewelry clear of all moving parts.

• DO NOT use in any commercial, rental or institutional setting. This product is intended for indoor, home-use only.

• DO NOT operate equipment while under the inﬂuence of drugs, alcohol, or medication that may cause drowsiness or disorientation.

• ALWAYS inspect the equipment prior to use. Make sure all fasteners are secure.

• ALWAYS replace defective components immediately and/or keep the equipment out of use until repair.

• ALWAYS position equipment on a level surface and away from water or ledges that could lead to accidental immersion or falls.

• Refer to additional warning notices posted on the equipment. If a product label or Owner’s Manual should become lost, damaged or

illegible, contact Customer Service for replacement.

Items for Assembly

Items not shown to scale. Hardware drawings located on the insert inside each Hardware Kit.

Table Bed Assembly

Use with Table Bed Assembly

Hardware Kit (HK1006)

IA1670

F51064

EP1105

ITEM NO. ITEM NAME

FitFlex™ Table Bed Assembly

IA1310A Upper Portion

IA1310B Lower Portion

HK1006 Table Bed Assembly Hardware Kit

A-Frame Base Assembly

NX1105 A-Frame

F51007 Angle Tether pre-assembled to A-Frame

Roller Hinge Assembly

F51064 3-Hole Roller Hinges (2)

Front Ankle Bar Assembly

F51045 Front Ankle Bar

HK1004 Front Ankle Bar Assembly Hardware Kit

Main Shaft Assembly

IA1600 with T-Pin Ankle Lock System

Handle Assembly

Use with Handle Assembly Hardware Kit

(HK1009)

Roller Hinge Assembly

Optional Head Pillow

IA1149

5 mm Allen Wrench

F51088

ITEM NO. ITEM NAME

Handle Assembly

IA1670 Traction Support™ Handles (2)

HK1009 Handle Assembly Hardware Kit

Hinge Cover Assembly

F11250 Hinge Covers (2)

HK1002 Hinge Cover Assembly Hardware Kit

Optional Accessories

EP1105 Head Pillow

Tools Provided for Assembly

IA1149 5 mm Allen Wrench (1)

F51088 Open-Ended Wrenches (2)

Product Support

LI7003 Getting Started DVD

LI7000 Owner’s Manual pre-assembled to A-Frame

F11250

IA310B

Open-Ended

Wrenches

Tools Provided for Assembly

IA310A

Front Ankle Bar Assembly

Use with Front Ankle Bar Assembly

Hardware Kit (HK1004)

F51045

A-Frame Base Assembly

with pre-assembled Angle Tether

NX1105

F51007

Main Shaft Assembly

with T-Pin Ankle Lock System

IA1600

Hinge Cover Assembly

Use with Hinge Cover Assembly

Hardware Kit (HK1002)

Getting Started DVD

LI7003

Product Support

LI7000

Owner’s Manual

Identifying Parts and Components

Understanding Your Inversion Table

Before reading further, study the drawing below to familiarize yourself with the

important components of your Teeter Inversion Table.

1 Head Pillow

2 Bed Frame Extension

3 Table Bed

4 Pivot Pins

5 Hinge Plates

6 Self-Locking Hooks

7 3-Hole Roller Hinges

8 Traction Support™ Handles

9 Height-Selector Locking Pin

10 Spreader Arms

11 Angle Tether

12 Crossbar

Located on

back of table

bed.

910

13 A-Frame

14 Main Shaft

15 Ankle Lock System with

Foam Rollers

16 Ankle Comfort Dial™

17 Non-Skid Stability Feet

The 700ia is shown here.

Your actual model may vary.

Safety Warning Labels and Product Speciﬁcations

Important: Please review all labels and supporting materials before using your inversion table.

This drawing indicates the locations of the warning labels found on your product. If a label is missing, illegible or is removed,

contact Teeter Customer Service to request a complimentary replacement label.

Note: Image and labels below not shown at actual size.

Assembled Non-Use Dimensions: 152.4 cm (L) x 73.2 cm (W) x 144.8 cm (H) (60 x 28.8 x 57 in)

Maximum In-Use Dimensions: 213.4 cm (L) x 73.2 cm (W) x 218.4 cm (H) (84 x 28.8 x 86 in)

Storage Dimensions: 55.9 cm (L) x 73.2 cm (W) x 167.6 cm (H) (22 x 28.8 x 66 in)

Weight (approx.): 26.98 kg (59.5 lb)

73 cm (28.8 in)

150.5 cm (57 in)

152.4 cm (60 in)

The 700ia is shown here.

Unpack and Prepare Your Workspace

• If possible, set up the product at or near the space in which you intend to use it to avoid moving it later.

• Unpack all parts and support materials. Set aside packing materials and clear your work area.

• Locate the Hardware Kits packaged with the manuals. They are labeled to correspond with the assembly process.

• The Getting Started DVD provides step-by-step instructions on how to assemble your product. You may find it helpful to follow along

with the DVD by watching it on either your TV or computer. The DVD is divided into the following sections:

• Assembly - Follow step-by-step instructions on how to assemble your inversion table.

• User Settings - Personalize your inversion experience by adjusting four customizable settings.

• Use Instructions - Learn how to test your balance and rotation control, and how to properly invert and return upright.

• Advanced Stretching and Exercises - Use your Teeter for rotational stretches, sit ups, squats and more!

• BONUS Healthy Back Classes*

Get guided instruction on stretches and exercises you can do on your own to help strengthen your back and gain flexibility.

*Not available in French or Spanish.

Before Beginning Assembly

With a QR code reader app, scan the barcodes next to each assembly step to watch the corresponding

video to guide you through the instructions.

Follow the Assembly Steps with Your Smartphone!

STEP 1

Assemble Table Bed and A-Frame Base

Assemble the Upper and Lower Portions

of the Table Bed

NOTE: Do not detach the Bed Frame Extension from the clips.

• Locate the Table Bed Assembly Hardware Kit (HK1006)

• Lay the Upper and Lower Portions of the Table Bed face down on

the floor (Figure 1).

• Gently lift the base of the pre-assembled Bed Frame Extension

while sliding the Lower Portion and Frame onto the Upper Portion.

Align the shaft of the frame into the plastic track of the Upper

Portion (Figure 2).

• Align the bolt holes of the upper part of the frame (triangle-shaped

area) to the bolt holes on the Upper Portion. Release the Bed Frame

Extension so that it rests on top of the bolt holes (Figure 3).

• Reaching underneath, insert one of the shorter bolts through one

of the holes in the Upper Portion and hold in place. Slide one of the

Bed Frame Extension loops over the bolt and handtighten with a

nut (Figures 3 and 3a). Repeat with other side.

• Reaching underneath, insert the longest bolt into the lower hole

(Figure 2) and hand-tighten with a nut.

• To fully tighten all three nuts to the bolts, insert the Allen Wrench

into the bolt heads and tighten the nuts using a 10/13 mm Open-

Ended Wrench.

FIGURE 1

FIGURE 2

FIGURE 3

Lower Hole / Longer Bolt

Upper Holes / Shorter Bolts

1 - Bolt 2 - Loop

FIGURE 3a

Assemble the A-Frame Base

• On a level surface, position the A-Frame so that it is standing upright

and the Stability Feet are on the ground.

• Gently push down on the Spreader Arms to ensure they are fully open

and in the “locked” position (Figure 4).

• Look for temporary circular assembly assistance labels on the

A-Frame. RIGHT, LEFT, FRONT, and REAR indicate your position while

using the equipment, not facing it. These labels can be removed easily

upon completion of assembly.

1 - Spreader Arms 2 - Crossbar

LEFT

RIGHT

FIGURE 4

REAR

FRONT

LOCKED

FIGURE 4a

UNLOCKED

STEP 2

Assemble Roller Hinges to Table Bed

UNLOCKED

Bracket Pin Cam Lock

Pivot Pin Bracket

UNLOCK LOCK

LOCKED

FIGURE 5

FIGURE 7

FIGURE 6

FIGURE 8

FIGURE 9

NEVER disassemble the Roller Hinge Pivot Pin.

WARNING

• For ease of assembly, rest the Table Bed against the Crossbar

(Figure 6) at the front of the A-Frame.

• On one side of the Table Bed, lift and hold the Cam Lock up all

the way to unlock (Figure 7).

• In your other hand, hold one Roller Hinge near the Pivot Pin.

With the Pivot Pin facing out (away from the Table Bed), slide the

bottom of the Roller Hinge between the Cam Lock and the Bracket.

TIP: Make sure that the Cam Lock is completely open when inserting

the Roller Hinge, otherwise assembly will be more difficult.

• Engage one of the holes in the Roller Hinge over the Bracket Pin.

Figure 9 shows the Roller Hinge installed correctly, with the

Bracket Pin engaged in Setting C.

NOTE: Refer to the Owner’s Manual for an explanation of the hole

settings. If you are unsure, use Setting C to start.

• Push down on the Cam Lock (Figure 8) to lock it and secure the

Roller Hinge.

• Repeat on other side. Make sure the Roller Hinges are in the

same hole setting on both sides.

• Familiarize yourself with the 3-Hole Roller Hinge and Cam Lock

terms (Figure 5).

STEP 3

Assemble Table Bed to A-Frame

The 700ia is shown here. Your actual model may vary.

• Face the front of the A-Frame where the Crossbar is located (Figure 10).

• Grasp both Roller Hinges, right above the Cam Lock, and lift the

Table Bed. Allow the top of the Table Bed to rotate toward the floor

so that the back of the Table Bed is now facing you and the top of the

Table Bed is in front of the Crossbar (Figure 11).

• Lower each Roller Hinge Pivot Pin into the A-Frame hinge plates one

side at a time (Figure 12). The Self-Locking Hooks will open to allow the

Pivot Pin into the Hinge Plate slot, then automatically snap closed

over the Pivot Pin.

TIP: You may need to push outward on the Hinge Plate in order for

the second Pivot Pin to lock in place.

• Make sure that each Pivot Pin is seated at the base of the slot in the

Hinge Plates and that the Self-Locking Hooks have closed over both

Pivot Pins (Figures 12a and 12b).

Failure of the Self-Locking Hooks to close over both Roller Hinge

Pivot Pins is an indication of improper assembly and if not corrected

could result in serious injury or death!

WARNING

• Rotate the Table Bed into the use position (Figure 13). Ensure that

it rotates smoothly. See also Image A on Page 12 to ensure

correct assembly.

TOP VIEW

INSIDE VIEW

FRONT

REAR

FIGURE 12

FIGURE 13

FIGURE 12b

FIGURE 12a

FIGURE 10

FIGURE 11

STEP 4

Assemble Front Ankle Bar to Main Shaft

The 700ia is shown here. Your actual model may vary.

NOTE: Extending out from the Front Ankle Bar, you will see a

temporary plastic zip-tie fastened to the loops of the Retainer Spring

with the Cable. This is provided to assist with the assembly process,

detailed below.

• With hole settings of the Front Ankle Bar facing up, insert the

temporary plastic zip-tie and Front Ankle Bar into the Front Ankle

Bar housing (Figure 14) of the Main Shaft.

• Pull up on the T-Pin Lock to allow the Front Ankle Bar to insert all

the way into the housing. Release the T-Pin to fully engage in the

hole setting closest to the front Foam Rollers (Figure 14a).

• Turn over the Main Shaft (Figure 15). From the back side of the Front

Ankle Bar housing, pull the plastic zip-tie to stretch the Retainer

Spring and Cable Loops so that they align with the bolt holes in the

back of the Front Ankle Bar housing.

• Insert the Bolt through the hole in the outer side of the housing,

through both the Retainer Spring and Cable Loops, and through the

hole in the other side of the housing (Figure 15a).

• Release your hold on the plastic zip-tie. Secure the Bolt with the Nut

(Figure 16) using the 10/13 mm Open-Ended Wrench provided.

IMPORTANT: Cut the long segment of zip-tie off so that it will not

interfere with the function of the Retainer Spring. Be careful not to

damage the Retainer Spring with the Cable.

• Cover the open end of the Front Ankle Bar Housing with the End

Cap (Figure 16a).

FIGURE 14

FIGURE 15

Large Arrow: Pull up on the T-Pin.

Small Arrow: Insert the Front Ankle Bar

into the Front Anke Bar Housing.

Failure to assemble the T-Pin Ankle Lock System could

result in serious injury or death!

WARNING

1 - Front Ankle Bar Housing

FIGURE 14a

1 - Retainer Spring and Cable Loop 2 - Temporary Zip-Tie

FIGURE 15a

FIGURE 16 FIGURE 16a

FULLY ENGAGED

STEP 5

The 700ia is shown here. Your actual model may vary.

• Facing the front of the A-Frame, hold the Main Shaft in your left hand

with the height markings facing up. Slide the end of the Main Shaft

into the Main Shaft Housing (Figure 17) located at the base of the

Table Bed.

• With your right hand, pull out the Height-Selector Locking Pin

(Figure 18) to allow the Main Shaft to slide in further and release

in the desired height setting. Refer to the Owner’s Manual for more

information on selecting your height setting.

• The Main Shaft MUST REST against the Crossbar bumper on the

A-Frame (Figure 19).

IMPORTANT: The Crossbar prevents the Table Bed from rotating

forward when the user steps on the Ankle Comfort Dial. If the

Main Shaft does not rest on the Crossbar bumper as shown in

Figure 19, then the Table Bed has been assembled backwards

onto the A-Frame.

This MUST BE CORRECTED before use. See also Image B on Page 12

to ensure correct assembly.

• Test the inversion table by hand for smooth and steady rotation

(Figure 20) and ensure that all fasteners are secure.

FIGURE 17

FIGURE 18

FIGURE 19

FIGURE 20

Assemble Main Shaft to Table Bed

STEP 6

Assemble Handles and Hinge Covers

The 700ia is shown here. Your actual model may vary.

FIGURE 21

FIGURE 22

• Locate the Handle Assembly Hardware Kit (HK1009).

• Insert the left and right handles into the A-Frame (Figure 21) so the

long part of the handles are parallel with the rear legs of the A-Frame.

• Insert the Bolts from inside of the A-Frame and fasten with the Nuts

from the outside of the A-Frame (Figure 22).

• Tighten with the open-ended wrenches provided.

• Locate the Hinge Cover Assembly Hardware Kit (HK1002).

• Select the corresponding Hinge Covers for the left and right sides of

the A-Frame by aligning each with the shape of the Hinge Plate

(Figure 23).

• Secure with (2) Allen Head Bolts for each side using the 5 mm Allen

Wrench provided. Be careful not to overtighten.

FIGURE 23

12 The 700ia is shown here. Your actual model may vary.

Attach Angle Tether

• The tether will come pre-assembled to the A-Frame.

• Unfold the adjustable tether and clip it to the U-Bar on the

underside of the Table Bed (Figure 24).

• Slide the buckle to lengthen or shorten the strap depending on

your desired maximum angle of inversion.

Attach Head Pillow

Attach the Head Pillow by securing the Velcro Straps through the

holes in the Table Bed (Figure 25). You may customize the position

depending on your preference.

LENGTHEN

SHORTEN

FIGURE 24

FIGURE 25

STEP 7

Attach Angle Tether and Head Pillow

Image B

Go back to Step 3 for instruction.

Demonstrates that the Table Bed has been

assembled into the A-Frame backwards so the

Main Shaft is not resting on the Crossbar and must be corrected.

Image A

Go back to Step 2 for instruction.

Demonstrates that the Roller Hinges have been

assembled upside down into the Table Bed

and must be corrected.

Misassembly Check

If your Teeter Inversion Table looks like either of these images, your inversion table has

been misassembled and is unfit for use. Improper assembly could result in serious injury or death!

WARNING

The 700ia is shown here. Your actual model may vary.

Before Inverting

Ensure Owner’s Manual is Attached

The Owner’s Manual contains important information on how to use

your Teeter Inversion Table, including how to personalize the user

settings, properly secure and release the Ankle Lock System, and test

and adjust the rotation control.

• If not already attached, thread the provided metal chain through

the pre-punched hole in the upper corner of the Owner’s Manual.

• Secure the chain to the A-Frame through the designated hole in the

Hinge Plate (Figure 26 and 26a). Allow the Owner’s Manual to hang

freely on the outside of the A-Frame Spreader Arms so it doesn’t

interfere with the rotation of the Table Bed.

IMPORTANT: Once attached to the A-Frame, DO NOT remove the

Owner’s Manual. It should remain permanently attached to your

inversion table to serve as a reference for all users in regards to proper

adjustment and use of the equipment.

WARNING

View the Remainder of the DVD

The Getting Started DVD is a helpful supplement to the Owner’s Manual,

with easy-to-follow instructions on user settings, how to invert, storage

and maintenance, and even stretching and exercises you can do with

your Teeter.

Read the Owner’s Manual thoroughly before using your

Teeter Inversion Table. Improper settings could result

in serious injury or death!

FIGURE 26a

FIGURE 26

The 700ia is shown here. Your actual model may vary.

HOW TO SUBMIT YOUR REGISTRATION:

Step 1

Fill out this information for your own records.

Step 2

Go online to teeter.com to register your warranty.

Handling and transportation costs related to product warranty service only are covered by this warranty. This warranty does

not cover damage resulting from improper handling, assembly, or installation, repairs made by others, accident, misuse,

or abuse. Under no circumstances shall Teeter, or any other party involved in the sale of this product, have any liability for

incidental or consequential damage arising from breach of an express or implied warranty on any Teeter product.

EXCEPT AS SET FORTH ABOVE, NO WARRANTY IS GIVEN WITH RESPECT TO ANY TEETER PRODUCT, AND ALL EXPRESS

WARRANTIES ARE DISCLAIMED. This warranty shall be governed by the laws of the State of Washington, USA. To

the extent this warranty is found not to be enforceable, it shall be deemed revised to the extent necessary to make it

enforceable. This warranty and any controversy or claim arising out of this warranty or its interpretation shall be governed

by the laws of the State of Washington, USA. Any controversy or claim arising out of or relating to this warranty, its

interpretation, or any alleged breach thereof, which cannot be amicably settled between Teeter and the owner within

sixty (60) days of written notice by the aggrieved party to the other, shall be ﬁnally settled by arbitration submitted to

three (3) arbitrators selected from the panels of the arbitrators of the American Arbitration Association located closest to

Teeter’s principal place of business.

Some provinces/states do not allow the exclusion of incidental or consequential damage from a warranty, so the above

limitation or exclusion may not apply to you. Some provinces/states do not allow limitations on how long an implied

warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal rights, and you may also

have other rights which may vary depending on your province/state. This warranty is completely transferable to any and

all future owners of this product, provided no alterations have been made to the product.

PLEASE RETAIN THIS FOR YOUR RECORDS

Date of Purchase

Product & Model

Dealer Name

Serial No.

YEAR

FULL

During the period starting with the day of retail purchase and continuing for ﬁve (5) years, Teeter

extends to the owner a repair and replacement warranty against manufacturing defects in

materials, workmanship, fabrics and padding. Teeter will repair or replace any such defect and will

pay the costs of all parts, labour and transportation. If a repair or replacement is not commercially

practical or cannot timely be made, then Teeter will, at the original Purchaser’s option, replace

with a comparable product or refund the purchase price.

FULL 5-YEAR WARRANTY

If you are unable to go online, you can request a warranty card to be mailed to you by calling Customer Service at 800-847-0143.

Please DO NOT mail this to Teeter.

The Teeter warranty set forth below and on Teeter’s website applies to US and Canadian customers only.

For international customers, please consult your local distributor for warranty information, which will vary

depending on country.

U.S. and Foreign Patents Apply. Teeter and Teeter logo are registered trademarks of Teeter. Speciﬁcations subject to change without notice.

If you have any trouble assembling the equipment, or questions

about its use, please contact customer service.

Medical Device Safety Service

GmbH

Schiffgraben 41

30175 Hannover

Germany

Tel. +49 511 62628630

EC REP

International: Teeter International, Ltd.

Gor-Ray House

758 Great Cambridge Rd

Enﬁeld

Middlesex EN1 3GN

United Kingdom

teeterintl.com | inf[email protected]

USA: Teeter

9902 162nd St. Ct. E.

Puyallup, WA 98375

Toll Free: 800-847-0143

Fax: 800-847-0188

teeter.com | inf[email protected]

Any modiﬁcation to this device will void the UL Listing.

This product is Listed by

Underwriters Laboratories Inc.

Representative samples of this

product have been evaluated

by UL and meet applicable

safety standards.

USA: 800-847-0143 or info@teeter.com

International: info@teeterintl.com

Check out the selection of products and accessories

available at teeter.com!

Roger Teeter

Founder & Innovator

700ia

Table d’inversion

Pour télécharger et imprimer le manuel du propriétaire 700ia, visitez la page d’assistance des produits au teeter.com

* Les spéciﬁcations techniques de cette image

peuvent changer et sont sujettes à des

changements sans préavis..

Instructions de montage

NOUVEAU!

Suivez avec votre

téléphone intelligent

pour rendre le montage

encore plus facile!

Appareil d’étirement et de décompression par gravité

GARANTIE

Manuel d’utilisation (fourni avec le matériel)

Instructions de sécurité importantes . . . . . . . . . . . . . . . 1

Réglages de l’utilisateur............................ 2

Préparez-vous à l’inversion ......................3 – 4

Inversion .......................................4 – 5

Rangement et entretien ........................... 5

Tirez le maximum de votre Teeter.................. 6

Instructions de montage

Instructions de sécurité importantes ............... 1

Éléments de montage ............................. 2

Comprendre sa table d’inversion ................... 3

Étiquettes d’avertissement de sécurité et spéciﬁcations

du produit......................................... 4

Avant de commencer le montage ................. 5

Étapes du montage ...........................6 – 11

Vériﬁcation d’un mauvais montage................ 12

Avant l’inversion .................................. 13

Conditions de garantie et enregistrement ......... 15

Merci d’avoir acheté la table d’inversion 700ia de Teeter! Pour proﬁter pleinement de votre nouvelle acquisition, vous devez d’abord

suivre les instructions de montage et lire et comprendre le manuel d’utilisation qui l’accompagnent, de même que visionner le DVD

d’apprentissage.

Les appareils de décompression de Teeter sont conçus pour une utilisation domestique et peuvent être utilisés par plusieurs

adultes. Ils permettent d’exercer une traction non assistée sur la colonne vertébrale et ainsi d’étirer les muscles et les tissus mous

paravertébraux.

Approuvé par Santé Canada, les appareils de décompression de Teeter sont indiqués pour les problèmes suivants : maux de dos,

tensions musculaires, discopathie dégénérative, arthrose de la colonne vertébrale, sténose vertébrale, hernie discale, courbure

rachidienne attribuable à des tensions musculaires, sciatique, spasmes musculaires et syndrome des facettes.

Pour enregistrer la garantie de votre produit, rendez-vous sur teeter.com/Support/Warranty-Registration

Si vous avez des questions concernant le montage ou si des pièces manquent, NE RENVOYEZ PAS L’ARTICLE AU MAGASIN

ET NE CONTACTEZ PAS LE VENDEUR. Nos experts en service à la clientèle peuvent vous aider au 800.847.0143, ou par

formulaires en lignes ou clavardage en direct sur teeter.com.

Suivez les étapes de montage avec votre téléphone intelligent! Avec une application de lecture de code

QR, scannez les codes-barres après chaque étape de montage pour regarder la vidéo correspondante

pour vous guider au fur et à mesure des instructions.

La page charge ...

Teeter 700ia Assembly Instructions

Marque: Teeter

Modèle: 700ia

Taper: Assembly Instructions

Télécharger le PDF

rapport

dans d''autres langues

English: Teeter 700ia

Teeter 700ia Assembly Instructions

Teeter 700ia Assembly Instructions

dans d''autres langues

Documents connexes

Autres documents