Teeter EP-960 Assembly Instructions

ASSEMBLY INSTRUCTIONS

* Speciﬁcations may vary from this image and are subject to change without notice.

EN

For gravity-assisted stretching and decompression

ComforTrak

™

Series Inversion Tables

FASTER, BETTER

RESULTS WITH

TEETER SUPPORT

& COACHING

ASSEMBLE FASTER

Free BILT® app puts easy 3-D

instructions at your ﬁngertips.

Search ‘Teeter’ in BILT® to

get started.

EASY ACCESS TO VIDEO

Access videos online for easy

assembly guidance, how-to’s

and classes.

Scan or

Go to

teeter.com/videos

FREE EXERCISE GUIDE

Register your warranty and gain

access to our 30-Day Back Pain

Relief Guide.

Scan or

Go to

teeter.com/warranty

REACH YOUR GOALS

Use the free Teeter Move™ app

to access guided sessions,

product support, and more!

Scan or

Find BILT® in

your App Store

Scan or

Find Teeter Move™

in your App Store

Owner’s Manual (attached to the equipment)

Important Safety Instructions .........................1

User Settings .........................................2

Prepare to Invert ...................................3 – 4

Inverting ...........................................4 – 5

Storage & Maintenance............................... 5

Get the Most out of Your Teeter ......................6

Assembly Instructions

Important Safety Instructions .........................1

Items for Assembly ...................................2

Understanding Your Inversion Table ................. 3

Safety Warning Labels & Product Speciﬁcations.....4

Before Beginning Assembly.......................... 5

Assembly Steps....................................6 – 11

Misassembly Check...................................12

Before Inverting ......................................13

Warranty Terms & Registration .......................15

Congratulations on your purchase of a Teeter ComforTrak™ Inversion Table!

For the best experience, it is critical that you follow the assembly instructions,

and read and fully understand the Owner’s Manual attached to the equipment

before inverting. Teeter Decompression Devices are multiple user, reusable

medical devices for home use, intended to provide traction to the spine while

stretching the para‑spinal muscle and soft tissues. The devices provide

non‑powered traction and are meant for use by adults.

Teeter inversion tables are FDA‑Registered as 510(k) medical devices.

Indicated for:

If you have any questions concerning assembly or if any parts are missing,

DO NOT RETURN THE ITEM TO THE STORE OR CONTACT THE RETAILER.

Our dedicated product service experts can help! Contact Teeter Customer Service

at 800-847-0143, or via online forms or Live Chat at teeter.com.

Trust Teeter for unmatched quality and performance, backed by our

industry‑leading warranty coverage. To register your product warranty,

go to teeter.com/Support/Warranty-Registration

• Herniated disc

• Spinal curvature due to tight muscles

• Sciatica

• Muscle spasm

• Facet syndrome

• Back pain

• Muscle tension

• Degenerative disc disease

• Spinal degenerative joint disease

• Spinal stenosis

WELCOME TO THE TEETER FAMILY

We’ve Got Your Back!

YEAR

5

W

A

R

A

N

T

Y

FULL

I created Teeter so people

could live healthier and

more active lives.

SAVE THESE INSTRUCTIONS 1

WARNING

!

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING THE INVERSION TABLE

BEFORE YOU BEGIN: Review all steps before beginning assembly and read all precautions before using the inversion table.

Carefully adhere to the Assembly Instructions and Owner’s Manual to help ensure safety and product integrity.

FAILURE TO FOLLOW INSTRUCTIONS AND WARNINGS COULD RESULT IN SERIOUS INJURY OR DEATH.

To reduce the risk of injury:

• Read and understand all the instructions, review all other accompanying documents, and inspect the equipment before using the

inversion table. It is your responsibility to familiarize yourself with the proper use of this equipment and the inherent risks of inversion

if these instructions are not followed, such as falling on your head or neck, pinching, entrapment, equipment failure, or aggravating a

pre‑existing medical condition. It is the responsibility of the owner to ensure that all users of the product are fully informed about the

proper use of the equipment and all safety precautions.

• DO NOT use until approved by a licensed physician. Inversion is contraindicated in any medical or health condition that may be made

more severe by an elevation of blood pressure, intracranial pressure or mechanical stress of the inverted position, or that may impact

your ability to operate the equipment. This may include injury or illness, but also the side effects of any drug or supplement (prescribed

or over‑the‑counter). Speciﬁc conditions may include, but not be limited to:

· Any condition, neurological or otherwise, which results in unexplained tingling, weakness or neuropathy, seizure, sleep disorder,

lightheadedness, dizziness, disorientation, or fatigue, or impacts strength, mobility, alertness, or cognitive ability;

· Any brain condition, such as trauma, history of intracranial bleed, history or risk of TIA or stroke, or severe headaches;

· Any condition of the heart or circulatory system, such as high blood pressure, hypertension, increased risk of stroke, or use of

anticoagulants (including high doses of aspirin);

· Any bone, skeletal or spinal cord condition or injury, such as signiﬁcant spinal curvature, acutely swollen joints, osteoporosis,

fractures, dislocations, medullary pins or surgically implanted orthopedic supports;

· Any eye, ear, nasal or balance condition, such as trauma, history of retinal detachment, glaucoma, optic hypertension, chronic

sinusitis, middle or inner ear disease, motion sickness, or vertigo;

· Any digestive or internal condition, such as severe acid reﬂux, hiatal or other hernia, gallbladder or kidney disease;

· Any condition for which exercise is speciﬁcally directed, limited or prohibited by a physician, such as pregnancy, obesity,

or recent surgery.

• ALWAYS be certain the Ankle Lock System is properly adjusted and fully engaged, and that your ankles are secure before using

the equipment. HEAR, FEEL, SEE and TEST that the Ankle Lock System is snug, close‑ﬁtting and secure EVERY TIME you use the

equipment.

• ALWAYS wear securely tied lace‑up shoes with a ﬂat sole, such as a normal tennis‑style shoe.

• DO NOT wear any footwear that could interfere with securing the Ankle Lock System, such as shoes with thick soles, boots, high‑tops

or any shoe that extends above the anklebone.

• DO NOT use the inversion table until it is adjusted properly for your height and body weight. Improper settings can cause rapid

inversion or make returning upright difﬁcult. New users, and users who are physically or mentally compromised, will require the

assistance of a spotter. Make sure the equipment is set to your unique user settings prior to each use.

• DO NOT sit up or raise head to return upright. Instead, bend knees and slide your body to the foot‑end of the inversion table to change

weight distribution. If locked out in full inversion, follow the instructions for releasing from the locked position before returning upright.

• DO NOT continue using the equipment if you feel pain or become light‑headed or dizzy while inverting. Immediately return to the

upright position for recovery and eventual dismount.

• DO NOT use if you are over 6 ft 6 in (198 cm) or over 300 lbs. (136 kg). Structural failure could occur or head/neck may impact the ﬂoor

during inversion.

• DO NOT allow children to use this machine. Keep children, bystanders, and pets away from machine while in use. The inversion table

is not intended for use by persons with reduced physical, sensory or mental capabilities, unless they are given supervision and

instruction concerning use of the machine by a person responsible for their safety.

• DO NOT store the inversion table upright if children are present. Fold and lay the table on the ﬂoor. DO NOT store outdoors.

• DO NOT use aggressive movements, or use weights, elastic bands, any other exercise or stretching device or non‑Teeter® attachments

while on the inversion table. Use the inversion table only for its intended use as described in this manual.

• DO NOT drop or insert any object into any opening. Keep body parts, hair, loose clothing and jewelry clear of all moving parts.

• DO NOT use in any commercial, rental or institutional setting. This product is intended for indoor, home‑use only.

• DO NOT operate equipment while under the inﬂuence of drugs, alcohol, or medication that may cause drowsiness or disorientation.

• ALWAYS inspect the equipment prior to use. Make sure all fasteners are secure.

• ALWAYS replace defective components immediately and/or keep the equipment out of use until repair.

• ALWAYS position equipment on a level surface and away from water or ledges that could lead to accidental immersion or falls.

• Refer to additional warning notices posted on the equipment. If a product label or Owner’s Manual should become lost, damaged or

illegible, contact Customer Service for replacement.

E61520

(EP‑860, EP‑960, EP‑970)

2

Items for Assembly

Items not shown to scale. Hardware drawings located on the insert inside each Hardware Kit.

Stretch-and-Grip™ Base Assembly

with pre‑assembled Angle Tether

E61100

F51007 (EP‑560)

F51008

(EP‑860, EP‑960, EP‑970) Main Shaft

with T‑Pin

Ankle Lock System

(EP‑560 & EP‑860

Models Only)

ComforTrak™ Table Bed Assembly

E61300

E61500 (EP‑560)

F51064 (EP‑560, EP‑860)

E61105

ITEM NO. ITEM NAME

Stretch-and-Grip™ A-Frame Base Assembly

E61100 A‑Frame

F51007 Angle Tether (EP‑560) pre‑assembled to A‑Frame

F51008 EZ Angle Tether (EP‑860, EP‑960, EP‑970)

pre‑assembled to A‑Frame

Handle Assembly

E61500 Stretch Assist™ Handles (2) (EP‑560)

E61520 Stretch Max™ Handles (2) (EP‑860, EP‑960, EP‑970)

HK1008 Handle Assembly Hardware Kit

Roller Hinge Assembly

F51064 3‑Hole Roller Hinges (2) (EP‑560, EP‑860)

TR1003 3‑Hole Roller Hinges w/Traction Handles (2)

(EP‑560 Sport, EP‑960, EP‑970)

ComforTrak™ Table Bed Assembly

E61300 ComforTrak™ Table Bed

Handle Assembly

Use with Handle Assembly

Hardware Kit (HK1008)

Roller Hinge Assembly

Optional Head Pillow

Tools Provided for Assembly

IA1149

5mm Allen Wrench

Main Shaft

with EZ‑Reach™

Ankle Lock System

(EP‑960 Model Only)

E61630

F51088

(EP‑860, EP‑960, EP‑970 only)

Open-Ended Wrench

Main Shaft

with Deluxe EZ‑Reach™

Ankle Lock System

(EP‑970 Model Only)

NX1620

ITEM NO. ITEM NAME

Main Shaft Assembly

E61601 with T‑Pin Ankle Lock System (EP‑560, EP‑860)

E61630 with EZ‑Reach™ Ankle Lock System (EP‑960)

NX1620 with Deluxe EZ‑Reach™ Ankle Lock System (EP‑970)

Optional Accessories

E61105 Head Pillow

Tools Provided for Assembly

IA1149 5mm Allen Wrench (1)

F51088 Open‑Ended Wrench (EP‑860, EP‑960, EP‑970)

Product Support

E61710 Owner’s Manual (EP‑560, EP‑860)

E61711 Owner’s Manual (EP‑960)

E61771 Owner’s Manual (EP‑970)

TR1003 (EP‑560 Sport, EP‑960, EP‑970)

E61601

Product Support

E61710 (EP‑560, EP‑860)

E61711 (EP‑960)

E61771 (EP‑970)

Owner’s Manual

Pre‑assembled

to A‑frame

REV. DESCRIPTION

REV.DATE

APP.DATE

APPROVED

STL-20150420-說明書 2015/4/20

C

A

B

D

E

6

5

4

3

29

8

7

C

A

B

D

E

F

G

H

1

23456789

F

G

H

REV. DESCRIPTION

REV.DATE

APP.DATE

APPROVED

STL-20150420-說明書 2015/4/20

C

A

B

D

E

6

5

4

3

29

8

7

C

A

B

D

E

F

G

H

1

23456789

F

G

H

3

Identifying Parts and Components

Understanding Your Inversion Table

Before reading further, study the drawing below to familiarize yourself with the

important components of your Teeter Inversion Table.

1 Head Pillow

2 Bed Frame Extension

3 ComforTrak™ Table Bed

4 Pivot Pins

5 Hinge Plates

6 Self‑Locking Hooks

7 3‑Hole Roller Hinges

8 Handles

9 Height‑Selector Locking Pin

10 Spreader Arms

11 Angle Tether

12 Crossbar

Located on

back of table

bed.

1

2

3

9

10

8

13

11

15

16 17

4

5

6

7

14

12

13 A‑Frame

14 Main Shaft

15 Ankle Lock System

16 Ankle Comfort Dial™

17 Non‑Skid Stability Feet

The EP‑560 is shown here.

Your actual model may vary.

4

Safety Warning Labels & Product Speciﬁcations

Important: Please review all labels and supporting materials before using your inversion table.

This drawing indicates the locations of the warning labels found on your product. If a label is missing, illegible or is removed,

contact Teeter Customer Service to request a complimentary replacement label.

Note: Image and labels below not shown at actual size.

Assembled Non-Use Dimensions: 60.0 (L) x 28.8 (W) x 58.5 in (H) (152.4 x 73.2 x 148.6 cm)

Maximum In-Use Dimensions: 84.0 (L) x 28.8 (W) x 86.0 in (H) (213.4 x 73.2 x 218.4 cm)

Storage Dimensions: 20.0 (L) x 28.8 (W) x 66.0 in (H) (50.8 x 73.2 x 167.6 cm)

Weight (approx.): EP‑560: 59 lbs (26.7 kg)

EP‑860: 61 lbs (27.7 kg)

EP‑960: 65 lbs (29.5 kg)

EP‑970: 65 lbs (29.5 kg)

28.8 in (73.2 cm)

58.5 in (148.6 cm)

60.0 in (152.4 cm)

The EP‑560 is shown here.

Your actual model may vary.

Before Beginning Assembly

5

For step‑by‑step, 3D interactive instructions, download BILT (a FREE mobile app) to your

smartphone to follow along. Simply download the BILT app by scanning the QR code

below and then search for your model (EP‑560, EP‑860, EP‑960 or EP‑970) within the

BILT app to get started!

Making Assembly Even Easier with

Unpack and Prepare Your Workspace

• If possible, assemble the equipment at or near the space in which you intend to use it to avoid moving it later.

• Unpack all parts and support materials. Set aside packing materials and clear your work area.

• Locate the Hardware Kits packaged with the manuals. They are labeled to correspond with the assembly process.

STEP 1

Assemble A-Frame Base & Stretch Assist Handles

• Follow these instructions if you have an EP‑560 model.

• On a level surface, position the A‑Frame so that it is standing upright

and the Stability Feet are on the ground.

• Gently push down on the Spreader Arms to ensure they are fully open

and in the “locked” position (Figure 1).

• Look for temporary circular assembly assistance labels on the

A‑Frame. RIGHT, LEFT, FRONT, and REAR indicate your position while

using the equipment, not facing it. These labels can be removed easily

upon completion of assembly.

• Locate the Handle Assembly Hardware Kit (HK1008).

• Determine the left or right handles, marked with an embossed L / R

on the inside of the black plastic part of each handle.

• Align the black plastic part of the corresponding handle (left / right)

over the outside edge of the Hinge Plate on the A‑Frame (Figure 2).

• Insert and loosely hand‑tighten three of the Allen Head Screws

through the Hinge Plate into the handle (Figure 3).

• Repeat with other handle. Tighten all fasteners with the Allen Wrench

provided, being careful not to over‑tighten.

• Proceed to Page 8 for Step 2.

6

1 ‑ Spreader Arms 2 ‑ Crossbar

LEFT

RIGHT

FIGURE 1

1

2

REAR

FRONT

For EP‑560 Models

FIGURE 2

FIGURE 3

LOCKED

FIGURE 1a

UNLOCKED

7

STEP 1

Assemble A-Frame Base & Stretch Max Handles

• Follow these instructions if you have an EP‑860, EP‑960,

or EP‑970 model.

• On a level surface, position the A‑Frame so that it is standing upright

and the Stability Feet are on the ground.

• Gently push down on the Spreader Arms to ensure they are fully open

and in the “locked” position (Figure 4).

• Look for temporary circular assembly assistance labels on the

A‑Frame. RIGHT, LEFT, FRONT, and REAR indicate your position while

using the equipment, not facing it. These labels can be removed easily

upon completion of assembly.

• Locate the Handle Assembly Hardware Kit (HK1008).

• Determine the left or right handles, marked with an embossed L / R

on the inside of the black plastic part of each handle.

• Position the lower handle portion of the corresponding handle

(left / right) at the rear junction of the A‑frame leg and Spreader

Arm (Figure 5 & 5a). The Lower Handle Bolt with Spacer has been

assembled loosely so that you will be able to seat the U‑shaped

portion of the lower handle over the Spacer in between the

Spreader Arm and the A‑frame leg. Do not tighten the bolt yet.

• Keeping the lower handle portion seated onto the Spacer, align the

upper handle portion’s black plastic part over the outside edge of the

Hinge Plate on the A‑Frame (Figure 6 & 6a).

• Insert and loosely hand‑tighten three of the Allen Head Screws

through the Hinge Plate into the handle (Figure 7).

• Now tighten the Lower Handle Bolt using the Allen Wrench and

Open Wrench provided, ensuring that it is fully secured but not

over‑tightened (Figure 8).

• Finally, tighten the Allen Head Screws for the upper handle using

the Allen Wrench provided.

• Repeat these steps on the other handle.

FIGURE 5a

For EP‑860, EP‑960, & EP‑970 Models

FIGURE 5

FIGURE 6

FIGURE 6a

FIGURE 7 FIGURE 8

1 ‑ Spreader Arms 2 ‑ Crossbar

LEFT

RIGHT

FIGURE 4

1

2

REAR

FRONT

LOCKED

FIGURE 4a

UNLOCKED

8

UNLOCKED

Bracket Pin Cam Lock

Pivot Pin Bracket

C

B

A

STEP 2

Assemble Roller Hinges to Table Bed

UNLOCK LOCK

LOCKED

NEVER disassemble the Roller Hinge Pivot Pin.

ALWAYS insert the 3‑Hole Roller Hinge (with the Pivot Pin on top

and facing out) in the same direction as the arrow label located

inside of the Cam Lock for proper assembly.

WARNING

!

NOTE: Some models come with Traction Handles pre‑assembled to

the Roller Hinges. However, the assembly instructions detailed below

still apply.

• For ease of assembly, rest the Table Bed against the Crossbar

(Figure 10) at the front of the A‑Frame.

• On one side of the Table Bed, lift and hold the Cam Lock up all

the way to unlock (Figure 11).

• In your other hand, hold one Roller Hinge near the Pivot Pin.

With the Pivot Pin facing out (away from the Table Bed), slide the

bottom of the Roller Hinge between the Cam Lock and the Bracket in

the same direction as the arrow label located inside of the Cam Lock.

TIP: Make sure that the Cam Lock is completely open when inserting

the Roller Hinge, otherwise assembly will be more difficult.

• Engage one of the holes in the Roller Hinge over the Bracket Pin.

Figure 13 shows the Roller Hinge installed correctly, with the

Bracket Pin engaged in Setting C.

NOTE: Refer to the Owner’s Manual for an explanation of the hole

settings. If you are unsure, use Setting C to start.

• Push down on the Cam Lock (Figure 12) to lock it and secure the

Roller Hinge.

• Repeat on other side. Make sure the Roller Hinges are in the

same hole setting on both sides.

For All Models

The EP‑560 is shown here. Your actual model may vary.

FIGURE 9

FIGURE 11

FIGURE 10

FIGURE 12

FIGURE 13

• Familiarize yourself with the 3‑Hole Roller Hinge and Cam Lock

terms (Figure 9).

9

• Face the front of the A‑Frame where the Crossbar is located (Figure 14).

• Grasp both Roller Hinges, right above the Cam Lock, and lift the

Table Bed. Allow the top of the Table Bed to rotate toward the floor,

so that the back of the Table Bed is now facing you and the top of the

Table Bed is in front of the Crossbar (Figure 15).

• Lower each Roller Hinge Pivot Pin into the A‑Frame hinge plates, one

side at a time (Figure 16). The Self‑Locking Hooks will open to allow the

Pivot Pin into the Hinge Plate slot, then automatically snap closed

over the Pivot Pin.

TIP: You may need to push outward on the Hinge Plate in order for

the second Pivot Pin to lock in place.

• Make sure that each Pivot Pin is seated at the base of the slot in the

Hinge Plates, and that the Self‑Locking Hooks have closed over both

Pivot Pins (Figures 16a & 16b).

Failure of the Self‑Locking Hooks to close over both Roller Hinge

Pivot Pins is an indication of improper assembly and if not corrected

could result in serious injury or death!

WARNING

!

STEP 3

Assemble Table Bed to A-Frame

• Rotate the Table Bed into the use position (Figure 17). Ensure that

it rotates smoothly. See also Image A on Page 12 to ensure

correct assembly.

TOP VIEW

INSIDE VIEW

FRONT

REAR

For All Models

FIGURE 16

FIGURE 17

FIGURE 16b

FIGURE 16a

FIGURE 14

FIGURE 15

The EP‑560 is shown here. Your actual model may vary.

10

• Your model’s Main Shaft may differ from what is shown in the

figures, however the assembly instructions remain the same.

• Facing the front of the A‑Frame, hold the Main Shaft in your left hand

with the height markings facing up. Slide the end of the Main Shaft

into the Main Shaft Housing (Figure 18), located at the base of the

Table Bed.

• With your right hand, pull out the Height‑Selector Locking Pin

(Figure 19) to allow the Main Shaft to slide in further and release

in the desired height setting. Refer to the Owner’s Manual for more

information on selecting your height setting.

• The Main Shaft MUST REST against the Crossbar bumper on the

A‑Frame (Figure 20).

IMPORTANT: The Crossbar prevents the Table Bed from rotating

forward when the user steps on the Ankle Comfort Dial. If the

Main Shaft does not rest on the Crossbar bumper as shown in

Figure 20, then the Table Bed has been assembled backwards

onto the A‑Frame.

This MUST BE CORRECTED before use. See also Image B on Page 12

to ensure correct assembly.

• Test the inversion table by hand for smooth and steady rotation

(Figure 21) and ensure that all fasteners are secure.

STEP 4

Assemble Main Shaft to Table Bed

For All Models

FIGURE 18

FIGURE 19

The EP‑560 is shown here. Your actual model may vary.

FIGURE 20

FIGURE 21

11

STEP 5

Attach Angle Tether & Head Pillow

Attach Angle Tether

• The tether will come pre‑assembled to the A‑Frame.

• Unfold the adjustable tether and clip it to the U‑Bar on the

underside of the Table Bed (Figure 22).

• Slide the buckle to lengthen or shorten the strap depending on

your desired maximum angle of inversion.

Attach Head Pillow

Attach the Head Pillow by securing the Velcro Straps through the

specified holes in the Table Bed (Figure 23), which allow the pillow

to shift with the user when in use. You may also customize the

position depending on your preference.

LENGTHEN

SHORTEN

For All Models

FIGURE 22

FIGURE 23

The EP‑560 is shown here. Your actual model may vary.

EZ-Angle Tether Accessory

Some models may come with the EZ‑Angle Tether, embroidered

with color‑coded angle markers at 20° (GREEN), 40° (ORANGE),

or 60° (RED). Simply slide the buckle so its center aligns with your

desired color setting.

12

Image B

Go back to Step 3 for instruction.

Demonstrates that the Table Bed has been

assembled into the A‑Frame backwards so the

Main Shaft is not resting on the Crossbar and must be corrected.

Image A

Go back to Step 2 for instruction.

Demonstrates that the Roller Hinges have been

assembled upside down into the Table Bed

and must be corrected.

Misassembly Check

If your Teeter Inversion Table looks like either of these images, your inversion table has

been misassembled and is unfit for use. Improper assembly could result in serious injury or death!

WARNING

!

For All Models

The EP‑960 is shown here. Your actual model may vary.

Before Inverting

Ensure Owner’s Manual is Attached

The Owner’s Manual contains important information on how to use

your Teeter Inversion Table, including how to personalize the user

settings, properly secure and release the Ankle Lock System, and test

and adjust the rotation control.

• If not already attached, thread the provided metal chain through

the pre‑punched hole in the upper corner of the Owner’s Manual.

• Secure the chain to the A‑Frame through the designated hole in the

Hinge Plate (Figure 24 & 24a). Allow the Owner’s Manual to hang freely

on the outside of the A‑Frame Spreader Arms so it doesn’t interfere

with the rotation of the Table Bed.

IMPORTANT: Once attached to the A‑Frame, DO NOT remove the

Owner’s Manual. It should remain permanently attached to your

inversion table to serve as a reference for all users in regards to proper

adjustment and use of the equipment.

WARNING

!

Read the Owner’s Manual thoroughly before using your

Teeter Inversion Table. Improper settings could result

in serious injury or death!

For All Models

FIGURE 24a

FIGURE 24

The EP‑560 is shown here. Your actual model may vary. 13

Watch the Getting Started Videos

The Getting Started Video Portal is a helpful supplement to the Owner’s Manual, with easy‑to‑follow

instructions on user settings, how to invert, storage and maintenance, and even stretching and exercises

you can do with your Teeter. Access via teeter.com/videos and search your Teeter Model now!

HOW TO SUBMIT YOUR REGISTRATION:

Step 1

Fill out this information for your own records.

Step 2

Go online to teeter.com to register your warranty.

Handling and transportation costs related to product warranty service only are covered by this warranty. This warranty does

not cover damage resulting from improper handling, assembly, or installation, repairs made by others, accident, misuse,

or abuse. Under no circumstances shall Teeter, or any other party involved in the sale of this product, have any liability for

incidental or consequential damage arising from breach of an express or implied warranty on any Teeter product.

EXCEPT AS SET FORTH ABOVE, NO WARRANTY IS GIVEN WITH RESPECT TO ANY TEETER PRODUCT, AND ALL EXPRESS

WARRANTIES ARE DISCLAIMED. This warranty shall be governed by the laws of the State of Washington, USA. To

the extent this warranty is found not to be enforceable, it shall be deemed revised to the extent necessary to make it

enforceable. This warranty and any controversy or claim arising out of this warranty or its interpretation shall be governed

by the laws of the State of Washington, USA. Any controversy or claim arising out of or relating to this warranty, its

interpretation, or any alleged breach thereof, which cannot be amicably settled between Teeter and the owner within

sixty (60) days of written notice by the aggrieved party to the other, shall be ﬁnally settled by arbitration submitted to

three (3) arbitrators selected from the panels of the arbitrators of the American Arbitration Association located closest to

Teeter’s principal place of business.

Some states do not allow the exclusion of incidental or consequential damage from a warranty, so the above limitation or

exclusion may not apply to you. Some states do not allow limitations on how long an implied warranty lasts, so the above

limitation may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which may

vary from state to state. This warranty is completely transferable to any and all future owners of this product, provided no

alterations have been made to the product.

PLEASE RETAIN THIS FOR YOUR RECORDS

Date of Purchase

Product & Model

Dealer Name

Serial No.

YEAR

5

W

A

R

A

N

T

Y

FULL

During the period starting with the day of retail purchase and continuing for ﬁve (5) years, Teeter

extends to the owner a repair and replacement warranty against manufacturing defects in

materials, workmanship, fabrics and padding. Teeter will repair or replace any such defect and will

pay the costs of all parts, labor and transportation. If a repair or replacement is not commercially

practical or cannot timely be made, then Teeter will, at the original Purchaser’s option, replace

with a comparable product or refund the purchase price.

FULL 5 YEAR WARRANTY

If you are unable to go online, you can request a warranty card to be mailed to you by calling Customer Service at 800-847-0143.

Please DO NOT mail this to Teeter.

15

The Teeter warranty set forth below and on Teeter’s website applies to US and Canadian customers only.

For international customers, please consult your local distributor for warranty information which will vary

depending on country.

U.S. and Foreign Patents Apply. Teeter and Teeter logo are registered trademarks of Teeter. Speciﬁcations subject to change without notice.

If you have any trouble assembling the equipment, or questions

about its use, please contact customer service.

USA: 800‑847‑0143 or info@teeter.com

International: info@teeterintl.com

Check out the selection of products and accessories

available at teeter.com!

Roger Teeter

Founder & Innovator

Teeter Decompression Devices are multiple user, reusable devices for home use, intended to provide traction to the spine while stretching the para‑spinal muscles and soft tissues.

The devices provide non‑powered traction and are meant for use by adults.

Use of the Teeter Decompression Devices is indicated for the following conditions: back pain, muscle tension, degenerative disc disease, spinal degenerative joint disease, spinal stenosis,

herniated disc, spinal curvature due to tight muscles, sciatica, muscle spasm, and facet syndrome.

Medical Device Safety Service

GmbH

Schiffgraben 41

30175 Hannover

Germany

Tel. +49 511 62628630

EC REP

Any modiﬁcation to this device will void the UL Listing.

This product is Listed by

Underwriters Laboratories Inc.

Representative samples of this

product have been evaluated

by UL and meet applicable

safety standards.

If you have any trouble assembling the equipment, or questions

about its use, please contact customer service.

Phone: 800‑847‑0143

Email: info@teeter.com

Teeter

9713 233rd Avenue East Ste A

Bonney Lake, WA 98391

Toll Free: 800‑847‑0143

Fax: 800‑847‑0188

teeter.com | info@teeter.com

Série ComforTrak

TM

Instructions de montage

Modèles EP-560, EP-860, EP-960, EP-970

FR

NOUVEAU !

Suivez avec votre

téléphone intelligent

pour rendre le montage

encore plus facile !

ANS

5

G

A

R

A

N

T

I

E

COMPLÈTE

Appareil d’étirement et de décompression par gravité

Pour télécharger et imprimer le manuel de la série ComforTrak™ de Teeter,

visitez la page d’assistance des produits au teeter.com

* Les spéciﬁcations techniques de cette image

peuvent changer et sont sujettes à des

changements sans préavis..

Manuel d’utilisation (fourni avec le matériel)

Instructions de sécurité importantes ................ 1

Réglages de l’utilisateur .............................2

Préparez-vous à l’inversion........................3 – 4

Inversion..........................................4 – 5

Rangement & Entretien.............................. 5

Conseils & réponses aux questions

fréquemment posées ...............................6

Instructions de montage

Instructions de sécurité importantes ................ 1

Éléments de montage ..............................2

Comprenez votre table d’inversion .................. 3

Étiquettes d’avertissement de sécurité et

spéciﬁcations de produit ............................ 4

Avant de commencer le montage .................. 5

Étapes du montage ............................. 6 – 11

Vériﬁcation d’un mauvais montage ................. 12

Avant l’inversion .................................... 13

Conditions de garantie & Enregistrement........... 15

Merci d’avoir acheté la table d’inversion de la série ComforTrak™ Series de Teeter ! Pour proﬁter pleinement de votre nouvelle

acquisition, vous devez d’abord suivre les instructions de montage et lire et comprendre le manuel d’utilisation qui l’accompagnent,

de même que visionner le DVD d’apprentissage.

Les appareils de décompression de Teeter sont conçus pour une utilisation domestique et peuvent être utilisés par plusieurs

adultes. Ils permettent d’exercer une traction non assistée sur la colonne vertébrale et ainsi d’étirer les muscles et les tissus mous

paravertébraux.

Approuvé par Santé Canada, les appareils de décompression de Teeter sont indiqués pour les problèmes suivants : maux de dos,

tensions musculaires, discopathie dégénérative, arthrose de la colonne vertébrale, sténose vertébrale, hernie discale, courbure

rachidienne attribuable à des tensions musculaires, sciatique, spasmes musculaires et syndrome des facettes.

Pour obtenir des instructions d’assemblage étape par étape en format 3D interactif sur votre téléphone intelligent,

téléchargez l’application BILT GRATUITE. La procédure de téléchargement de l’application BILT est expliquée en page 5.

Pour enregistrer la garantie de votre produit, rendez-vous sur teeter.com/Support/Warranty-Registration

Si vous avez des questions concernant le montage ou si des pièces manquent, NE RENVOYEZ PAS L’ARTICLE AU MAGASIN

OU NE CONTACTEZ PAS LE VENDEUR. Nos experts en service à la clientèle peuvent vous aider ! Service à la clientèle de

Teeter au 800.847.0143, ou par formulaires en lignes ou Chat en direct sur teeter.com.

Tirez le maximum de vos séances d’inversion en téléchargeant l’application TeeterLinkMC sur

votre téléphone : faites le suivi de votre utilisation et de votre niveau de douleur, recevez des

rappels et des conseils personnalisés, obtenez du soutien, et plus encore! Balayez le code ou

recherchez TeeterLink dans votre boutique d’applications.

La page charge ...

Teeter EP-960 Assembly Instructions

Ce manuel convient également à

Teeter EP-960 Assembly Instructions

dans d''autres langues

Documents connexes

Autres documents