Motorola CP110 VHF Manuel utilisateur

CP110

TM

Series / Série CP110

MC

Two-way Radios

Radios bidirectionnelles

User Guide

Guide de l’utilisateur

CP110 UHF and VHF Models / Modèles CP110 UHF et VHF

Motorola, the Stylized M Logo, and all other trademarks indicated as such herein are Trademarks of Motorola, Inc.

Motorola, le M stylisé du logo et toutes les autres marques de commerce indiquées comme telles dans le présent document

CONTENTS

English

1

CONTENTS

Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Introduction . . . . . . . . . . . . . . . . . . . . . . . . 5

Package Contents. . . . . . . . . . . . . . . . . . . . . .5

Batteries and Chargers Safety

Information . . . . . . . . . . . . . . . . . . . . . . . . . 7

Operational Safety Guidelines. . . . . . . . . . . . .8

FCC Licensing Information . . . . . . . . . . . . 9

Interference Information . . . . . . . . . . . . . . . . .9

Radio Overview . . . . . . . . . . . . . . . . . . . . 11

Parts of the Radio . . . . . . . . . . . . . . . . . . . . .11

On/Off/Volume Knob. . . . . . . . . . . . . . . .12

Channel Selector Knob. . . . . . . . . . . . . .12

Accessory Connector . . . . . . . . . . . . . . .12

Model Label . . . . . . . . . . . . . . . . . . . . . .12

Microphone . . . . . . . . . . . . . . . . . . . . . . .12

Antenna. . . . . . . . . . . . . . . . . . . . . . . . . .12

LED Indicator . . . . . . . . . . . . . . . . . . . . .12

Side Buttons . . . . . . . . . . . . . . . . . . . . . .12

Push-to-Talk (PTT) Button. . . . . . . . . . . 12

Side Button 1 (SB1) . . . . . . . . . . . . . . . . 12

Side Button 2 (SB2) . . . . . . . . . . . . . . . . 12

The Lithium-Ion (Li-Ion) Battery . . . . . . . 12

Batteries Features . . . . . . . . . . . . . . . . . . . . 14

About the Li-Ion Battery . . . . . . . . . . . . . 14

Battery Recycling and Disposal . . . . . . . 15

Installing the Lithium-Ion (Li-Ion)

Battery . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Removing the Lithium-Ion (Li-Ion)

Battery . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Alkaline Battery Pack

(Optional Accessory) . . . . . . . . . . . . . . . 17

Installing Alkaline Batteries . . . . . . . . . . 17

Removing Alkaline Batteries . . . . . . . . . 17

Attaching the Antenna . . . . . . . . . . . . . . 18

Removing the Antenna . . . . . . . . . . . . . 18

Installing Spring Action Belt Clip . . . . . . 19

Power Supply, Adaptor and Drop-in

Tray Charger . . . . . . . . . . . . . . . . . . . . . 19

Battery Life Information . . . . . . . . . . . . . 20

Alkaline Battery Life . . . . . . . . . . . . . . . . 20

Charging the Battery . . . . . . . . . . . . . . . 21

CONTENTS

English

2

Getting Started . . . . . . . . . . . . . . . . . . . . . 27

Turning radio ON/OFF. . . . . . . . . . . . . . . . . .27

Adjusting Volume . . . . . . . . . . . . . . . . . . . . .27

Selecting a Channel . . . . . . . . . . . . . . . . . . .27

Talking and Monitoring . . . . . . . . . . . . . . . . .27

Receiving a Call . . . . . . . . . . . . . . . . . . . . . .28

Talk Range . . . . . . . . . . . . . . . . . . . . . . . . . .28

Radio LED Indicators . . . . . . . . . . . . . . . . . .30

Hands-Free Use/VOX . . . . . . . . . . . . . . . . . .31

With Compatible VOX Accessories. . . . .31

Setting VOX Sensitivity. . . . . . . . . . . . . .32

Microphone Gain. . . . . . . . . . . . . . . . . . .32

Battery Save . . . . . . . . . . . . . . . . . . . . . .32

Reset to Factory Defaults . . . . . . . . . . . .32

End of Transmission Tone

(Roger Beep Tone) . . . . . . . . . . . . . . . . .32

Programming Features . . . . . . . . . . . . . . 33

Programming Mode. . . . . . . . . . . . . . . . . . . .33

Learning to Read the Values the

Radio Signals You . . . . . . . . . . . . . . . . .33

Entering Programming Mode . . . . . . . . .36

Frequencies Values . . . . . . . . . . . . . . . .36

Reading CTCSS/DPL Values . . . . . . . . 36

Reading Auto-Scan Values . . . . . . . . . . 37

Programming Codes and Auto-Scan . . . 38

Programming Mode FAQ. . . . . . . . . . . . 38

Programming Values Examples. . . . . . . . . . 40

Example of Programming a Code . . . . . 40

Example of Programming Auto-Scan . . 41

Other Programming Features . . . . . . . . . . . 41

Scan. . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Editing Scan List . . . . . . . . . . . . . . . . . . 42

Nuisance Channel Delete . . . . . . . . . . . 42

CPS (Computer Programming Software). . . 43

Bandwidth Select . . . . . . . . . . . . . . . . . . 44

Time-Out Timer . . . . . . . . . . . . . . . . . . . 44

Power Select . . . . . . . . . . . . . . . . . . . . . 45

Battery Type Setting . . . . . . . . . . . . . . . 45

Call Tones . . . . . . . . . . . . . . . . . . . . . . . 45

Scramble . . . . . . . . . . . . . . . . . . . . . . . . 45

Reverse Burst . . . . . . . . . . . . . . . . . . . . 46

Cloning Radios. . . . . . . . . . . . . . . . . . . . . . . 46

Cloning with a Multi Unit Charger

(MUC) . . . . . . . . . . . . . . . . . . . . . . . . . . 46

CONTENTS

English

3

Cloning Radio using the Radio to

Radio (R2R) Cloning Cable

(Optional Accessory). . . . . . . . . . . . . . . .48

Cloning using the CPS

(Computer Programming Software) . . . .50

Troubleshooting . . . . . . . . . . . . . . . . . . . . 51

Use and Care . . . . . . . . . . . . . . . . . . . . . . 55

Frequency and Code Charts . . . . . . . . . . 56

CP110™ VHF Frequencies Chart. . . . . . . . .56

CP110™ UHF Frequencies Chart. . . . . . . . .56

CTCSS and PL/DPL Codes . . . . . . . . . . . . .57

Motorola Limited Warranty for the

United States and Canada . . . . . . . . . . . . 60

Accessories . . . . . . . . . . . . . . . . . . . . . . . 64

Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . .64

Audio Accessories. . . . . . . . . . . . . . . . . . . . .64

Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65

Carry Accessories . . . . . . . . . . . . . . . . . . . . .66

Software and Cables. . . . . . . . . . . . . . . . . . .66

Chargers . . . . . . . . . . . . . . . . . . . . . . . . . . . .66

SAFETY

English

4

SAFETY

PRODUCT SAFETY AND RF

EXPOSURE COMPLIANCE

ATTENTION!

This radio is restricted to occupational use only

to satisfy FCC RF energy exposure

requirements.

For a list of Motorola-approved antennas,

batteries, and other accessories, visit the

following website which lists approved

accessories:

http://www.motorola.com

Before using this product,

read the operating

instructions and RF energy

awareness information

contained in the Product

Safety and RF Exposure

booklet enclosed with your

radio.

!

INTRODUCTION

English

5

INTRODUCTION

Thank you for purchasing the Motorola®

CP110™ Series Radio. This radio is a product

of Motorola’s 75 plus years of experience

as a world leader in the designing and

manufacturing of communications equipment.

The CP110™ Series radios provide cost-

effective communications for businesses

such as retail stores, restaurants, schools,

construction sites, manufacturing, property

and hotel management and more. Motorola

two-way radios are the perfect communications

solution for all of today’s fast-paced industries.

Note: Read this user guide carefully to ensure you

know how to properly operate the radio

before use

Business Radios,

RPSD 1C15, Motorola

8000 West Sunrise Boulevard

Plantation, Florida 33322

PACKAGE CONTENTS

•Radio

• VHF/UHF Antenna

• Spring Action Belt-Clip

• Lithium-Ion Battery

• Power Supply

•User Guide

• Drop-in Tray Charger

• Product Safety & RF Exposure Booklet

INTRODUCTION

English

6

For a copy of a large-print version of this user

guide or for product-related questions, contact:

1-800-924-2744 in the USA/Canada

1-888-390-6456 on your TTY

(Text Telephone)

BATTERIES AND CHARGERS

SAFETY INFORMATION

English

7

BATTERIES AND

CHARGERS SAFETY

INFORMATION

This document contains important safety and

operating instructions. Read these instructions

carefully and save them for future reference.

Before using the battery charger, read all the

instructions and cautionary markings on

• the charger,

• the battery, and

• the radio using the battery

1. To reduce risk of injury, charge only the

rechargeable Motorola-authorized batteries.

Other batteries may explode, causing personal

injury and damage.

2. Use of accessories not recommended by

Motorola may result in risk of fire, electric

shock, or injury.

3. To reduce risk of damage to the electric plug

and cord, pull by the plug rather than the cord

when disconnecting the charger.

4. An extension cord should not be used unless

absolutely necessary. Use of an improper

extension cord could result in risk of fire and

electric shock. If an extension cord must be

used, make sure that the cord size is 18AWG

for lengths up to 6.5 feet (2 m), and 16AWG

for lengths up to 9.8 feet (3 m).

5. To reduce risk of fire, electric shock, or injury,

do not operate the charger if it has been broken

or damaged in any way. Take it to a qualified

Motorola service representative.

6. Do not disassemble the charger; it is not

repairable and replacement parts are not

available. Disassembly of the charger may

result in risk of electrical shock or fire.

7. To reduce risk of electric shock, unplug the

charger from the AC outlet before attempting

any maintenance or cleaning.

BATTERIES AND CHARGERS

SAFETY INFORMATION

English

8

OPERATIONAL SAFETY

GUIDELINES

• Turn the radio OFF when charging battery.

• The charger is not suitable for outdoor use.

Use only in dry locations/conditions.

• Connect charger only to an appropriately fused

and wired supply of the correct voltage

(as specified on the product).

• Disconnect charger from line voltage by removing

main plug.

• The outlet to which this equipment is connected

should be nearby and easily accessible.

• In equipment using fuses, replacements must

comply with the type and rating specified in the

equipment instructions.

• Maximum ambient temperature around the power

supply equipment must not exceed 40°C (104°F).

• Power output from the power supply unit must not

exceed the ratings stated on the product label

located at the bottom of the charger.

• Make sure that the cord is located where it will

not be stepped on, tripped over, or subjected to

water, damage, or stress.

FCC LICENSING

INFORMATION

English

9

FCC LICENSING

INFORMATION

INTERFERENCE INFORMATION

This device complies with Part 15 of the FCC

Rules. Operation is subject to the condition that

this device does not cause harmful

interference.

CP110™ Series two-way radios operate on

radio frequencies that are regulated by the

Federal Communications Commission (FCC).

To transmit on these frequencies, you are

required to have a license issued by the FCC.

Application is made available on FCC Form

601 and Schedules D, H, and Remittance

Form 159.

To obtain these FCC forms, request document

000601 which includes all forms and

instructions. If you wish to have the document

faxed, mailed or have questions, use the

following contact information.

Faxed contact the

Fax-On- Demand

system at:

Mailed call the FCC forms hotline at:

Questions regarding FCC

license contact the FCC at:

1-202-418-0177 1-800-418-FORM

1-800-418-3676

1-888-CALL-FCC

1-888-225-5322

Or: http://www.fcc.gov

FCC LICENSING

INFORMATION

English

10

Before filling out your application, you must

decide which frequency(ies) you can operate

on. See “Frequencies and Code Charts”. For

questions on determining the radio frequency,

call Motorola Product Services at:

1-800-927-2744

Changes or modifications not expressly

approved by Motorola may void the user’s

authority granted by the FCC to operate this

radio and should not be made. To comply with

FCC requirements, transmitter adjustments

should be made only by or under the

supervision of a person certified as technically

qualified to perform transmitter maintenance

and repairs in the private land mobile and fixed

services as certified by an organization

representative of the user of those services.

Replacement of any transmitter component

(crystal, semiconductor, etc.) not authorized by

the FCC equipment authorization for this radio

could violate FCC rules.

Use of this radio outside the country where it

was intended to be distributed is subject to

government regulations and may be prohibited

RADIO OVERVIEW

English

11

RADIO OVERVIEW

PARTS OF THE RADIO

Channel Selector

Knob

PTT Button

SB1-Monitor

Button

SB2- Scan/

Nuisance

Channel

Delete

Antenna

Microphone

On/Off/Volume

Knob

LED Indicator

Accessory

Connector

Model Label

Lithium-Ion

Battery

RADIO OVERVIEW

English

12

On/Off/Volume Knob

Used to turn the radio ON or OFF and to adjust

the radio’s volume.

Channel Selector Knob

Used to switch the radio to different channels.

Accessory Connector

Used to connect compatible audio accessories.

Model Label

Indicates the model of the radio.

Microphone

Speaks clearly into the microphone when

transmitting.

Antenna

The radio antenna’s is removable.

LED Indicator

Used to give battery status, power-up status,

radio call information and scan status.

Side Buttons

Push-to-Talk (PTT) Button

• Press and hold down this button to talk, release it

to listen.

Side Button 1 (SB1)

• The Side Button 1 is a general button that can be

configured by the Computer Programming

Software - CPS. The default setting of SB1 is

‘Monitor’.

Side Button 2 (SB2)

• The Side Button 2 is a general button that can be

configured by the CPS. The SB2 default setting is

‘Scan/Nuisance Channel Delete’.

The Lithium-Ion (Li-Ion) Battery

CP110™ Series provides different types of

batteries. For more information, see “Batteries

Features” on page 14.

RADIO OVERVIEW

English

13

This User Guide covers multiple CP110™

Series models, and may detail some features

your radio does not have. The radio’s model is

shown on the front of the radio, underneath the

speaker, and provides you the following

information:

Model

Frequency

Band

Transmit

Power

(Watts)

Number of

Channels

Antenna

CP110 UHF 2 2 Removable

CP110 VHF 2 2 Removable

RADIO OVERVIEW

English

14

BATTERIES FEATURES

CP110™ Series radios provide Lithium-Ion

batteries that come in different capacities that

will define the battery life. It also offers the

option to use Alkaline batteries. The radio

comes equipped with a rapid charger.

About the Li-Ion Battery

The CP110™ Series radio comes equipped

with a rechargeable Li-Ion battery. This battery

should be charged before initial use to ensure

optimum capacity and performance.

Battery life is determined by several factors.

Among the more critical are the regular

overcharge of batteries and the average depth

of discharge with each cycle. Typically, the

greater the overcharge and the deeper the

average discharge, the fewer cycles a battery

will last. For example, a battery which is

overcharged and discharged 100% several

times a day, lasts fewer cycles than a battery

that receives less of an overcharge and is

discharged to 50% per day. Further, a battery

which receives minimal overcharging and

averages only 25% discharge, lasts even

longer.

Motorola batteries are designed specifically to

be used with a Motorola charger and vice

versa. Charging in non-Motorola equipment

may lead to battery damage and void the

battery warranty. The battery should be at

about 77°F (25°C) (room temperature),

whenever possible. Charging a cold battery

(below 50° F [10°C]) may result in leakage of

electrolyte and ultimately in failure of the

battery. Charging a hot battery (above 95°F

[35°C]) results in reduced discharge capacity,

affecting the performance of the radio.

Motorola rapid-rate battery chargers contain a

temperature-sensing circuit to ensure that

batteries are charged within the temperature

limits stated above.

RADIO OVERVIEW

English

15

Battery Recycling and Disposal

Li-Ion rechargeable batteries can be recycled.

However, recycling facilities may not be

available in all areas. Under various U.S. state

laws and the laws of several other countries,

batteries must be recycled and cannot be

disposed of in landfills or incinerators. Contact

your local waste management agency for

specific requirements and information in your

area. Motorola fully endorses and encourages

the recycling of Li-Ion batteries. In the U.S.

and Canada, Motorola participates in the

nationwide Rechargeable Battery Recycling

Corporation (RBRC) program for Li-Ion battery

collection and recycling.

Many retailers and dealers participate in this

program. For the location of the drop-off facility

closest to you, access RBRC’s Internet web

site at:

www.rbrc.com

or call:

1-800-8-BATTERY

This internet site and telephone number also

provides other useful information concerning

recycling options for consumers, businesses

and governmental agencies.

RADIO OVERVIEW

English

16

Installing the Lithium-Ion (Li-Ion) Battery

1. Turn OFF the radio.

2. With the Motorola logo side up on the battery

pack, fit the tabs at the bottom of the battery

into the slots at the bottom of the radio’s body.

3. Press the top part of the battery towards the

radio until a click is heard.

Note: To learn about the Li-Ion Battery Life

features, refer to “About the Li-Ion Battery”

on page 14.

Removing the Lithium-Ion (Li-Ion) Battery

1. Turn OFF the radio.

2. Push down the battery latch and hold it

depressed while removing the battery.

3. Pull the battery away from the radio.

Battery

Latch

slots

Battery

Latch

RADIO OVERVIEW

English

17

Alkaline Battery Pack (Optional Accessory)

Installing Alkaline Batteries

1. Turn OFF the radio, if it is turned ON.

2. Remove Li-Ion battery.

3. Assemble alkaline battery pack in the same

steps as installing the Li-Ion battery pack.

4. Remove battery door from alkaline battery pack.

5. Slide the 5 AA alkaline batteries into the frame,

matching the markings inside the compartment.

Removing Alkaline Batteries

1. Turn OFF the radio, if it is turned ON.

2. Slide the battery latches, on both sides of the

battery, downwards.

3. Pull the top of the battery away from the radio’s

body, and lift the battery from the radio’s body.

Alkaline

Battery

Door

Alkaline

Battery

Door

RADIO OVERVIEW

English

18

Attaching the Antenna

1. Align the threaded end of the antenna with the

radio’s antenna connector.

2. Turn the antenna clockwise to fasten it.

Removing the Antenna

1. Turn the antenna counterclockwise until you

can remove it.

La page est en cours de chargement...

Motorola CP110 VHF Manuel utilisateur

Ce manuel convient également à

Motorola CP110 VHF Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents