AEG T35850 Manuel utilisateur

Catégorie
Sèche-linge
Taper
Manuel utilisateur
LAVATHERM T35850
User manual Exhaust Dryer
Notice d'utilisation Sèche-linge à
évacuation
Thank you for choosing one of our high-quality products.
To ensure optimal and regular performance of your appliance please read this
instruction manual carefully. It will enable you to navigate all processes perfectly
and most efficiently. To refer to this manual any time you need to, we recommend
you to keep it in a safe place. And please pass it to any future owner of the appliance.
We wish you much joy with your new appliance.
Contents
Operating Instructions 3
Important safety information 3
Product description 5
Control panel 6
Before first use 6
Sorting and preparing laundry 6
Laundry weights 7
Programme overview 8
Daily use 9
Switching machine on / switching light on
9
Opening loading door / loading laundry
10
Selecting the programme 10
Selecting additional options 10
Setting delay timer 11
Starting the programme 11
Changing programme 11
Putting in extra items or taking items out
before end of programme 11
Drying cycle complete / removing laundry
11
Care and cleaning 12
Cleaning fluff filter 12
Cleaning the door 13
Cleaning the drum 13
Clean operating screen and housing 13
What to do if ... 14
Troubleshooting by yourself 14
Machine settings 15
BUZZER SIGNAL permanent off 15
Water hardness 15
Technical data 16
Installation 17
Appliance positioning 17
Removing transport safety packaging 17
Fitting the vent hose 18
Electrical connection 19
Changing door stop 19
Special accessories 19
Environment 20
Environmental tips 20
Service 21
Service 21
Guarantee/Customer Service Centres 21
Subject to change without notice
2
Contents
Operating Instructions
Important safety information
In the interest of your safety and to ensure the correct use, before installing and
first using the appliance, read this user manual carefully, including its hints and
warnings. To avoid unnecessary mistakes and accidents, it is important to ensure
that all people using the appliance are thoroughly familiar with its operation and
safety features. Save these instructions and make sure that they remain with the
appliance if it is moved or sold, so that everyone using it through its life will be
properly informed on appliance use and safety.
General safety
It is dangerous to alter the specifications or attempt to modify this product in any way.
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for
their safety.
Make sure that small pets do not climb into the drum. To avoid this, please check into
the drum before using.
Any objects such as coins, safety pins, nails, screws, stones or any other hard, sharp
material can cause extensive damage and must not be placed into the machine.
In order to avoid danger of fires caused by excessive drying, do not use appliance to dry
the following items: Cushions, quilts and the like (these items accumulate heat).
Items such as foam rubber (latex foam), shower caps, waterproof textiles, rubber backed
articles and clothes or pillows fitted with foam rubber pads should not be dried in the
tumble dryer.
Always unplug the appliance after use, clean and maintenance.
Under no circumstances should you attempt to repair the machine yourself. Repairs
carried out by inexperienced persons may cause injury or serious malfunctioning. Contact
your local Service Centre. Always insist on genuine spare parts.
Items that have been soiled with substances such as cooking oil acetone, petrol, kerosene,
spot removers, turpentine, waxes and wax removers should be washed in hot water with
an extra amount of detergent before being dried in the tumble dryer.
Danger of explosion: Never tumble dry items that have been in contact with inflam-
mable solvents (petrol, methylated spirits, dry cleaning fluid and the like). As these sub-
stance are volatile, they could cause an explosion. Only tumble dry items washed with
water.
Risk of fire: items that have been spotted or soaked with vegetable or cooking oil
constitute a fire hazard and should not be placed in the tumble dryer.
If you have washed your laundry with stain remover you must execute an extra rinse
cycle before loading your tumble dryer.
Important safety information
3
Please make sure that no gas lighters or matches have accidentally been left in pockets
of garments to be loaded into appliance
WARNING!
Never stop a tumble dry before the end of the drying cycle unless all items are
quickly removed and spread out so that the heat is dissipated. Risk of fire!
Risk of electric shock! Do not spray down the appliance with jets of water.
The final part of a tumble dryer cycle occurs without heat (cool down cycle) to ensure
that the items are left at a temperature that ensures that items will not be damaged.
Ensure you have adequate ventilation in the installation room to avoid the back flow of
gases into the room from appliances burning other fuels, including open fires.
Installation
This appliance is heavy. Care should be taken when moving it.
When unpacking the appliance, check that it is not damaged. If in doubt, do not use it
and contact the Service Centre.
All packing and transit bolts must be removed before use. Serious damage can occur to
the product and to property if this is not adhered to. See relevant section in the user
manual.
Any electrical work required to install this appliance should be carried out by a qualified
electrician or competent person.
Care must be taken to ensure that the appliance does not stand on the electrical supply
cable.
If the machine is situated on a carpeted floor, please adjust the feet in order to allow air
to circulate freely.
After having installed the appliance, check that it is not pressing or standing on its
electrical supply cable or/and inlet hose.
If the tumble dryer is placed on top of a washing machine, it is compulsory to use the
stacking kit (optional accessory).
Use
This appliance is designed for domestic use. It must not be used for purposes other than
those for which it was designed.
Only wash fabrics which are designed to be machine dried. Follow the instructions on
each garment label.
Do not dry unwashed items in the tumble dryer.
Do not overload the appliance. See the relevant section in the user manual.
Clothes which are dripping wet should not be placed in the dryer.
Garments which have been in contact with volatile petroleum products should not be
machine dried. If volatile cleaning fluids are used, care should be taken to ensure that
the fluid is removed from the garment before placing in the machine.
Never pull the power supply cable to remove the plug from the socket; always take hold
of the plug itself.
Never use the tumble dryer if the power supply cable, the control panel, the working
surface or the base are damaged so that the inside of the tumble dryer is accessible.
Fabric softeners, or similar products should be used as specified by the fabric softener
instructions.
4
Important safety information
Caution - hot surface : Do not touch the door light cover surface when the light is
switched on.
1)
Hot surface: Do not touch the back of the appliance while it is operating!
Child safety
This machine is not intended for use by young children or infirm persons without su-
pervision.
Children should be supervised to ensure that they do not play with the appliance.
The packaging components (e.g. plastic film, polystyrene) can be dangerous to children
- danger of suffocation! Keep them out of children’s reach.
Keep all detergents in a safe place out of children’s reach.
Make sure that children or pets do not climb into the drum.
Product description
1 Control panel
2 Door
3 Fluff filter
4 Lamp for inside light
5 Rating plate
6 Adjustable feet
7 Sideways vent outlets / back vent outlet
1
3
2
6
4
5
7
8
1) Only dryers equipped with internal drum light.
Product description
5
8 Ring nut
Control panel
1 Programme knob and OFF switch
2 Function buttons
3 START PAUSE button
4 DELAY START button
5 Function status led
Before first use
In order to remove any residues which may have been produced during production, wipe
the dryer drum with a damp cloth or carry out a brief drying cycle (ca. 30 min.) with damp
cloths in the machine.
Sorting and preparing laundry
Sorting laundry
Sort by fabric type:
Cotton/linen for programmes in COTTON programme group.
Mixtures and syntheticsfor programmes in SYNTHETICS programme group.
START
FILTER
DRYING
COOLING
END
PAUSE
DELAY START
DELICATE
SENSITIVE
LONG
ANTI-
CREASE
BUZZER
DRUM LIGHT
COTTONS
EASY CARE
EXTRA DRY
STORAGE DRY
IRON DRY
WOOL CARE
EASY IRON PLUS
SPORTS
LIGHT
JEANS
BED LINEN
FRESHEN-UP
30 MIN
OFF
EXTRA DRY
STORAGE DRY
IRON DRY
6h
9h
3h
6
Control panel
Sorting by care label. The care labels mean:
Drying in the tumble
dryer possible in prin-
ciple
Dry at normal tem-
perature
Dry at reduced tem-
perature (press DELI-
CATE button!)
Drying in the tumble
dryer not possible
Do not place in the appliance any wet laundry which is not specified on the care label as
being suitable for tumble-drying.
This appliance can be used for all wet laundry items which are labelled as suitable for
tumble-drying.
Do not dry new, coloured textiles together with light-coloured laundry items. Textile
colours may bleed.
Do not dry cotton jersey and knitwear with the EXTRA programme. Items may shrink!
Wool can be dried only by special programme WOOL CARE !
Preparing laundry
To avoid laundry becoming tangled: close zips, button up duvet covers and tie loose ties
or ribbons (e.g. of aprons).
Empty pockets. Remove metal items (paper clips, safety pins, etc).
Turn items with double-layered fabrics inside out (e.g. with cotton-lined anoraks, the
cotton layer should be outermost). These fabrics will then dry better.
Laundry weights
Type of laundry Weight
Bathrobe 1200 g
Napkin 100 g
Quilt cover 700 g
Sheet 500 g
Pillow case 200 g
Tablecloth 250 g
Towelling towel 200 g
Tea cloth 100 g
Night dress 200 g
Ladies' briefs 100 g
Man's work shirt 600 g
Man's work shirt 200 g
Man's pyjamas 500 g
Blouse 100 g
Men's underpants 100 g
Sorting and preparing laundry
7
Programme overview
Programmes
max. load (weight when dry)
Additional func-
tions/options
Application/properties
Care mark
DELICATE
SENSITIVE
LONG ANTICREASE
BUZZER
DELAY START
COTTON
EXTRA DRY
7 kg
Thorough drying of thick or multi- layered fabrics,
e.g. terry towelling items, bathrobes.
COTTON
STORAGE
DRY
1)
7 kg
Thorough drying of fabrics of even thicknesses, e.g.
terry towelling items, knitwear, towels.
COTTON
IRON DRY
1)
7 kg
For thin fabrics which are also to be ironed, e.g.
knitwear, cotton shirts.
SYNTHET-
ICS (syn-
thetics)EX-
TRA DRY
3 kg
Thorough drying of thick or multi-layered fabrics,
e.g. pullovers, bedding, table linen.
2)
SYNTHET-
ICS STOR-
AGE DRY
1)
3 kg
For thin fabrics which are not ironed, e.g. easy care
shirts, table linen, baby clothes, socks, lingerie with
bones or wires.
2)
SYNTHET-
ICS IRON
DRY
3 kg
For thin fabrics which are also to be ironed, e.g.
knitwear, cotton shirts.
2)
30 MIN 1 kg -
For further drying of individual items of laundry or
for small volumes of less than 1 kg.
FRESHEN
UP
1 kg -
For refreshing or gently cleaning textiles with
commercially available dry cleaning products.
BED LINEN 3 kg -
Bed linen (single and double sheet, pillowcase,
bedspread, duvet cover).
JEANS 7 kg
For leisure clothing, such as jeans, sweat-shirts,
etc., of different material thicknesses (e.g. at the
neck, cuffs and seams).
8
Programme overview
Programmes
max. load (weight when dry)
Additional func-
tions/options
Application/properties
Care mark
DELICATE
SENSITIVE
LONG ANTICREASE
BUZZER
DELAY START
SPORTS 2 kg
A
3)
-
For sportswear, thin fabrics, polyester, which are
not ironed.
EASY IRON
1 kg
(or 5
shirt
s)
A
A
ut
o
m
at
ic
)
-
Special programme with anti-crease mechanism
for easy care textiles such shirts and blouses; for
minimum ironing effort. The result depends on the
type and quality of textiles. (The loading volume
corresponds to approx. 5 to 7 shirts.) Recommen-
dation: Place textiles in the dryer straight after
spinning. Once dried, immediately remove textiles
and place on clothes hanger.
WOOL
CARE
1 kg - -
WOOL CARE is special programme for briefly treat-
ing woollens with warm air after they have been
dried naturally, worn or stored for long periods.
Wool fibres are aligned and the wool becomes soft
and snugly.
1) In accordance with IEC61121
2) select DELICATE option
3) Automatic
Daily use
Switching machine on / switching light on
Turn the programme selector to any programme. The machine has been switched on.
Daily use
9
Opening loading door / loading laundry
1. Open loading door:
Use force to push against the loading door
(push point)
2. Load your laundry (do not force it in).
CAUTION!
Do not jam laundry in between the loading
door and rubber seal.
3. Close loading door securely. Lock must
audibly lock.
Selecting the programme
Use the programme selector to set the programme you require.
Selecting additional options
The additional options available for the drying programmes are DELICATE , SENSITIVE , LONG
ANTICREASE and BUZZER
1. By turning the knob choose a drying programme.
2. To set the option press required option button. The corresponding lights on .
3. Press alternately option button to select appropriate options. START PAUSE icon flashes.
Some options cannot be selected together as DELICATE and SENSITIVE. Some of them are
not selectable with certain programmes
DELICATE
For especially gentle drying of sensitive fabrics
with the
care label and for temperature-sen-
sitive textiles (e.g. acrylic, viscose). Programme is
executed with reduced heat.
DELICATE is only suitable for use with loads of up
to 3kg.
LONG ANTICREASE
A long anti-crease phase lengthen the anti-crease phase (30 min.) at the end of the drying
additionally by 60 minutes. The drum rotates at intervals during this phase. This keeps the
laundry loose and free of creases. Phase lasts in total 90 minutes. The laundry can be
removed at any time during the anti-crease phase.
When the option is active, the LONG ANTICREASE light is on.
SENSITIVE
For gentle drying of fabrics that are frequently worn. Programme starts on full heat setting,
which is then reduced as the programme progresses to be kind to the washing.
10
Daily use
BUZZER
The appliance is supplied with the BUZZER function deactivated.
To activate buzzer choose BUZZER option.
The buzzer sounds or plays a tune during:
cycle end
anti-crease phase and when phase starts or ends
cycle interruption by a warning
–alarm
Setting delay timer
With the DELAY START button, you can delay the start of a programme by 3, 6 or 9
hours.
1. Select the programme and additional functions.
2. Press the DELAY START button as many times as necessary (the lights show which delay
time have been chosen).
3.
To activate the delay timer, press the START PAUSE button. The lights (9H, 6H, 3H)
change on every three hours until the time is getting on for start cycle.
Starting the programme
Press the START PAUSE button. The programme is started.
The programme phase is shown by appropriate lights. From up to the down, from DRYING ,
COOLING, to END .
Changing programme
To change a programme which has been selected by mistake once the programme has
started, first turn the programme selector to OFF position. The programme is cancelled.
The programme can no longer be changed directly once the programme has started. If
nevertheless there is an attempt to change the programme on the programme knob or if
an function button (excluding the BUZZER button) is pressed, led above START PAUSE
button starts flashing temporarily in yellow. The drying programme is not however affected
by this (laundry protection).
Putting in extra items or taking items out before end of programme
1. Open loading door.
WARNING!
Laundry and drum can become hot. Risk of burns!
2. Load or remove laundry items.
3. Close loading securely. Lock must audibly lock.
4. Press the START PAUSE button to continue the drying cycle.
Drying cycle complete / removing laundry
Once the drying cycle is complete, the lights END and FILTER are on. If the BUZZER button
has been pressed, an acoustic signal sounds intermittently for about one minute.
Daily use
11
The drying cycles (except for the and WOOL CARE programme) are automatically followed
by an anti-crease phase which lasts around 30 minutes. The drum rotates at intervals during
this phase. This keeps the laundry loose and free of creases. The laundry can be removed at
any time during the anti-crease phase. (The laundry should be taken out towards the end
of the anti-crease phase at the latest to prevent creases from forming.) If LONG ANTI-
CREASE function has been selected, the anti-crease phase is lengthened by 60 minutes.
1. Open door.
2. Remove laundry.
3. Remove filter after clothes has been removed. Clean the filter.
WARNING!
Before You place the filter , please check it there is nothing inside the filter seat.
4. Turn the programme selector to OFF.
Clean the filter after each drying cycle.
5. Close the door.
Care and cleaning
WARNING!
The tumble dryer is not to be used if industrial chemicals have been used for cleaning!
Cleaning fluff filter
The filter collect all the fluff which accumulates during drying. To ensure that the dryer
works perfectly, the fluff filter must be cleaned after every drying cycle.
The light ZEEF is on to remind you this operation.
CAUTION!
Never operate the dryer without fluff filter or with damaged or blocked fluff filter.
1. Open loading door and remove laundry.
2. Remove the filter which is built into the
lower part of the loading aperture.
12
Care and cleaning
3. Open the filter pressing the button,
among two slots on fingers. Clean the fil-
ter using dump hand or cloth. After a pe-
riod of time, a patina due to detergent
residue on laundry forms on the filters.
When this occurs, clean the filter with
warm water using a brush.
Close the filter and do not forget to put it
back.
WARNING!
Before You place the filter, please check it
there is nothing inside the filter seat.
4. The filter can be positioned only to one side. If position is wrong, the filter overhangs.
If the filter will not snap into place, the loading door cannot be closed.
WARNING!
You must DISCONNECT the appliance from the electricity supply, before you can carry out
any cleaning or maintenance work.
Cleaning the door
Clean periodically the interior part of the door to remove any fluff. Accurate cleaning
ensures correct drying.
Cleaning the drum
CAUTION!
Do not use abrasives or steel wool to clean the drum.
Lime in the water or cleaning agents may form a barely visible lining on the inside of the
drum. The degree to which the laundry has been dried is then no longer detected reliably.
The laundry is damper than expected when removed from the dryer.
Use a standard domestic cleaner (e.g. vinegar-based cleaner) to wipe down the inside of
the drum and drum ribs.
Clean operating screen and housing
CAUTION!
Do not use furniture cleaners or aggressive cleaning agents to clean the machine.
Use a damp cloth to wipe down the operating screen and housing.
Care and cleaning
13
What to do if ...
Troubleshooting by yourself
Problem Possible cause Remedy
Dryer does not work.
Mains plug is not plugged in or
fuse is not working correctly.
Plug in at mains socket. Check
fuse in fuse box (domestic in-
stallation).
Loading door is open. Close loading door.
Have you pressed the START
PAUSE button?
Press the START PAUSE button
again.
Drying results unsatisfactory.
Wrong programme selected.
Select a different programme
the next time you dry (see “Pro-
gramme chart” chapter).
Filter clogged. Clean filter.
Overloading of laundry.
Observe recommended loading
volumes.
Ventilation slots covered up. Uncover ventilation slots.
Residue on inside surface of
drum or drum ribs.
Clean inside surface of drum
and drum ribs.
Conductance of water at in-
stallation site differs from
standard setting of machine.
Re-programme standard set-
ting for degree of drying (see
‘Programming options’ chap-
ter).
Loading door does not close. Filter not in place. Install filter into place.
Drum light does not work.
Programme selector in OFF po-
sition.
Turn programme selector to
LIGHT or to any programme.
Defective light bulb.
Replace light bulb (see next
section).
Drying cycle ends shortly after
programme starts.
Not enough washing loaded or
washing loaded is too dry for
selected programme.
Select time programme or
higher drying level (e.g. EXTRA
DRYinstead of STORAGE DRY).
Drying cycle lasts an unusually
long time. Note: After around 5
hours the drying cycle ends au-
tomatically.
Filter clogged. Clean filter.
Load volume too big. Reduce load volume.
Laundry insufficiently spun.
Laundry must be adequately
spun.
Particularly high room temper-
ature. Temporary switching off
of the compressor to avoid
overload.
Automatic process, there is no
fault with the appliance. If pos-
sible, lower the room tempera-
ture.
14
What to do if ...
Changing the bulb for interior lighting
Only use a special bulb which is designed specially for dryers. The special bulb can be
obtained from your local service centre.
When the appliance is switched on, the interior lighting switches itself off after 4 minutes
when the door is open.
WARNING!
Do not use standard bulbs! These develop too much heat and may damage the machine!
Before replacing the bulb, disconnect the mains plug; with a permanent connection: fully
unscrew or deactivate the fuse.
1. Unscrew cover above the bulb (this can be found directly behind the loading aperture,
at the top; refer to “Description of machine” section.)
2. Replace defective bulb.
3. Screw cover back down.
Check the correct positioning of o-ring gasket before screwing back the door light cover.
Do not operate the dryer when missing o-ring gasket on door light cover.
WARNING!
For safety reasons, the cover must be screwed down tightly. If this is not done, the dryer
must not be operated.
Machine settings
BUZZER SIGNAL permanent off
1. Turn the programme selector to any programme. If the buzzer light is on, the buzzer
signal is active.
2. Press simultaneously the DELICATE and SENSITIVE buttons and hold down for approx.
5 seconds. The buzzer light is turn off. The buzzer signal is permanent off.
3. The buzzer is by default always off. You can use BUZZER button to activate or deactivate
sound but machine does not memorize your selection.
Water hardness
Water contains, a variable quantity of limestone and mineral salts of which quantities vary
according to geographical locations thus varying its conductivity values. Relevant varia-
tions of the conductivity of the water compared to those prefixed by the factory could
slightly influence the residual humidity of the laundry at the end of the cycle. Your dryer
allows you to regulate the sensitivity of the drying sensor based on conductivity values of
the water.
1. Turn the programme selector to any programme.
2. Press simultaneously the DELICATE and BUZZER buttons and hold down for approx. 5
seconds. The current setting is on the lights: light "END "– low conductivity <300 micro
S/cm, light "COOLING" – medium conductivity 300-600 micro S/cm,lightS "COOLING
"and "END"– high conductivity >600 micro S/cm
3. Press the START PAUZE button sequentially until you set desired level.
Machine settings
15
4. To memorize setting press simultaneously the DELICATE and BUZZER buttons or turn
knob to OFF position
Technical data
This appliance conforms with the following EU Directives:
2006/95/EC dated 12.12.2006 Low Voltage Directive
89/336/E.E.C dated 03.05.1989 EMC Directive inclusive of Amending Directive 92/31/EEC
93/68/EEC dated 22.07.1993 CE Marking Directive
Height x width x depth 85 x 60 x 58 cm
Drum volume 108 l
Depth with loading door open 109 cm
Height can be adjusted by 1.5 cm
Weight when empty approx. 32,5 kg
Loading volume (depends on programme)
1)
max. 7 kg
Voltage 220-240 V
Required fuse 13 A
Total power 2600 W
Energy efficiency class
C
Energy consumption (7 kg of cotton, pre-
drained at 1000 rpm)
2)
3.9 kWh
Average annual energy consumption 263.1 kWh
Use Domestic
Permissible ambient temperature + 5°C to + 35°C
Consumption values
The consumption values have been established under standard conditions. They may deviate when
the machine is operated in domestic circumstances.
Programme
Energy consumption in kWh / average dry-
ing time in min.
COTTON STORAGE DRY
2)
3)
3.9 / 95(7 kg load pre-drained at 1000 rpm)
COTTON IRON DRY
2)
3.05 / 75 (7 kg load pre-drained at 1000 rpm)
SYNTHETICS CUPBOARD DRY
2)
1.15 / 30 (3 kg load pre-drained at 1200 rpm)
1) Different loading volume data may be needed in some countries as a result of different measuring methods.
2) in accordance with EN 61121
16
Technical data
Installation
Appliance positioning
It is recommended that, for your convenience, the machine is positioned close to your
washing machine.
The tumble dryer must be installed in a clean place, where dirt does not build up.
Air must be able to circulate freely all round the appliance. Do not obstruct the front
ventilation grille or the air intake grilles at the back of the machine.
To keep vibration and noise to a minimum when the dryer is in use, it should be placed
on a firm, level surface.
Once in its permanent operating position, check that the dryer is absolutely level with
the aid of a spirit level. If it is not, raise or lower the feet until it is.
The feet must never be removed. Do not restrict the floor clearance through deeppile
carpets, strips of wood or similar. This might cause heat built-up which would interfere
with the operation of the appliance.
The hot air emitted by the tumble dryer can reach temperatures of up to 60°C. The appliance
must therefore not be installed on floors which are not resistant to high temperatures.
When operating the tumble dryer, the room temperature must not be lower than +5°C and
higher than +35°C, as it may affect the performance of the appliance.
WARNING!
Should the appliance be moved, it must be transported vertically.
WARNING!
The appliance must not be installed behind the lockable door, a sliding door or a door with
a hinge on the opposite side to that of the appliance.
Removing transport safety packaging
CAUTION!
Before use all parts of the transport packaging must be removed.
1. Open loading door
2. Pull off adhesive strips from inside ma-
chine on top of drum.
Installation
17
3. Remove foil hose and polystyrene pad-
ding from the machine.
Fitting the vent hose
To simplify the installation, there is a choice of vent outlets: one at the back, the others in
the left and right-hand side. Connect the hose to whichever is the more convenient by
pulling the ring nut (A) from the vent outlet at the back, screwing it on to the hose and
pushing it firmly back into place. The unused vents should now be sealed with the special
snap covers provided.
If the hose is long and the room temperature low,
the moisture might condense to water inside the
hose. This is an unavoidable natural phenomenon.
To prevent this water from Iying in the hose or
flowing back into the tumble dryer, it is advisable
to drill a small hole (via. 3 mm) in the lowest point
of the hose and to place a small container below
it. (See picture, point B).
Once connected to the dryer, run the vent hose to
the desired outlet point, ensuring that the run’s
overall length is less than 2 m, and that it contains
no more than two bends. As to the outlet itself, if
you have decided on a fixed wall/window grille, a
good local builder’s merchant should be able to
supply you with the necessary fittings and installation advice.
18
Installation
WARNING!
It is important not to connect the vent hose to, for
example, a cooker hood, or a chimney or flue pipe
designed to carry the exhaust from a fuel burning
appliance.
Note that to avoid condensation problems, it is
essential that the dryer be fitted with the flexible
hose to carry its “exhaust” at least beyond the
kitchen units; preferable outside the kitchen. In
order to prevent the appliance from overheating,
it is important that the steam exhaust is unob-
structed. Therefore, in case of a permanent hose
fitted to an exterior wall or ceiling, it must be en-
sured an exhaust capacity of at least 150 m3/h. If
the dryer is fitted next to kitchen units, make sure that the vent hose is not squashed. If
the hose is partially squashed, drying efficiency will be reduced, resulting in longer drying
times and higher energy consumption. If the hose is completely squashed, the safety cut-
outs with which the machine is fitted may operate. When operating the tumble dryer, the
room temperature must not be lower than +5°C and higher than +35°C, as it may affect
the performance of the appliance.
Electrical connection
Details on mains voltage, type of current and the fuses required should be taken from the
type plate. The type plate is fitted near the loading aperture (see “Product description”
chapter).
Connect the machine to an earthed socket, in accordance with current wiring reg-
ulations.
WARNING!
The manufacturer declines any responsibility for damage or injury through failure
to comply with the above safety precautions.
Should the appliance power supply cable need to be replaced, this must be carried
out by our Service Center.
WARNING!
The plug must be accessible after installing the machine.
Changing door stop
To make it easier to load or unload the laundry the door can be reversed. This operation
must be carried out by qualified personnel. Please contact the nearest Service Centre.
Special accessories
Stacking kit
Installation
19
A special stacking kit is available through your
dealer, to enable the mounting of the dyer on
top of a front loading washing machine with
cover’s depth between 48 and 60 cm. Read
carefully the instructions supplied with the kit.
Environment
The symbol on the product or on its packaging indicates that this product may not be
treated as household waste. Instead it should be taken to the appropriate collection point
for the recycling of electrical and electronic equipment. By ensuring this product is disposed
of correctly, you will help prevent potential negative consequences for the environment
and human health, which could otherwise be caused by inappropriate waste handling of
this product. For more detailed information about recycling of this product, please contact
your local council, your household waste disposal service or the shop where you purchased
the product.
Packaging material
The packaging materials are environmentally friendly and can be recycled. The plastic com-
ponents are identified by markings, e.g. >PE<, >PS<, etc. Please dispose of the packaging
materials in the appropriate container at the community waste disposal facilities.
WARNING!
When disposing of old appliances, remove the mains cable and dispose of together with
the plug. Remove the door hook and ensure it is no longer lockable to prevent young
children being trapped inside.
Environmental tips
In the dryer, laundry becomes fluffy and soft. Fabric softeners are not therefore needed
when washing.
20
Environment
1 / 1

AEG T35850 Manuel utilisateur

Catégorie
Sèche-linge
Taper
Manuel utilisateur

dans d''autres langues