Campbell Hausfeld WG4000 Manuel utilisateur

Marque: Campbell Hausfeld

Modèle: WG4000

Catégorie: Système de soudage

Taper: Manuel utilisateur

Ce manuel convient également à

Welder WG4000

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.

Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or

property damage! Retain instructions for future reference.

IN970800AV 3/03

Operating Instructions & Parts Manual Model WG4000

Wire Feed

Arc Welder

BUILT TO LAST

This Campbell Hausfeld wire feed welder

is designed to be used on standard 230

volt single phase current. The welder is

equipped with an infinite wire speed

control to accurately select the proper

wire feed rate needed for various

welding conditions. Internal components

are thermostatically protected.

This welder is designed for use with flux

core arc welding (gasless) or gas metal

arc welding (MIG) process. As delivered

from the factory, this welder can weld

with .030" (.8 mm) to .045” (1.2 mm)

diameter wire. A starter spool of .035”

(.9 mm) flux core wire and a .035” tip

are included.

Unpacking

Some welder components may be

found in the wire feed compartment.

When unpacking, inspect carefully for

any damage that may have occurred

during transit. Report any damaged or

missing items by calling (800) 746-5641.

Circuit Requirements

This equipment

requires a dedi-

cated 230 volt, minimum 20 amp circuit.

Do not run other appliances, lights, or

tools on this circuit while operating

this equipment. Extension cords are

not recommended. Blown fuses and

tripped circuit breakers can result from

failure to comply with this

recommendation.

Components and Controls

1. Work Clamp – Connects to work

piece.

2. Wire Feed Gun with .035” tip

3. Power Cord – Plugs into 230 volt

outlet.

CAUTION

4. On/Off/Heat Selector Switch –

Turns welder on and off and selects

welding power. Six (6) selections

are possible.

5. Infinite Wire Speed Control –

Controls wire speed (clockwise turn

increases speed; counterclockwise

turn decreases speed).

6. Polarity Hook-up (Inside Wire

Feed Compartment) – Provides

connections for MIG, direct current

electrode positive (DCEP); and flux

core, direct current electrode

negative (DCEN).

Danger means a

hazard that will

cause death or serious injury if the

warning is ignored.

DANGER

Warning means a

hazard that could

cause death or serious injury if the

warning is ignored.

Caution means a

hazard that may

cause minor or moderate injury if the

warning is ignored. It also may mean a

hazard that will only cause damage to

property.

NOTE: Note means any additional

information pertaining to the product

or its proper usage.

Always

keep a

fire extinguisher accessible

while performing arc welding

operations.

WARNING

CAUTION

WARNING

Need

Assistance?

Call Us First!

1-800-746-5641

Description

MODEL WG4000

Figure 1

General Safety

For parts, manuals, product & service information

visit www.chpower.com

or call (800) 746-5641.

FLU

FLUX

CORE

MIG

Wire Feed Gun (2)

Work

Clamp (1)

Power Cord (3)

Infinite Wire

Speed Control (5)

Polarity Hook-up (6)

On/Off/Heat Selector

Switch (4)

REMINDER: Keep your dated proof of purchase for warranty purposes! Attach it to this manual or file it for safekeeping.

Wire Feed Arc Welder

● Before starting or servicing any

electric arc welder, read and

understand all instructions. Failure

to follow safety precautions or

instructions can cause equipment

damage and/or serious personal

injury or death.

● All installation, maintenance, repair

and operation of this equipment

should be performed by qualified

persons only, in accordance with

national, state, and local codes.

Improper

use of

electric arc welders can cause

electric shock, injury, and

death! Take all precautions

described in this manual to reduce the

possibility of electric shock.

● Verify that all components of arc

welder are clean and in good

condition prior to operating the

welder. Be sure that the insulation

on all cables, wire feed gun, and

power cords is not damaged.

Always repair or replace damaged

components before operating

welder. Always keep welder panels,

shields, etc. in place when operating

the welder.

● Always wear dry, protective

clothing, welding gloves, and

insulated footwear.

● Always operate welder in a clean,

dry, well ventilated area. Do not

operate it in humid, wet, rainy, or

poorly ventilated areas.

● Be sure work piece is properly

supported and grounded before

beginning any electric arc welding

operation.

● Coiled welding cable should be

spread out before use to avoid

overheating and damage to

insulation.

Never immerse the

wire or wire feed

gun in water. If the welder becomes

wet for any reason, be absolutely

certain that it is completely clean and

dry before using!

● Always shut equipment off and

unplug power prior to moving

welder.

● Always attach work lead first.

● Verify that work piece is securely

grounded.

● Always shut off electric arc welding

equipment when not in use, and cut

off any excess wire from wire feed

gun.

DANGER

WARNING

● Never allow any part of body to

touch wire and ground or grounded

work piece at the same time.

● Awkward welding conditions and

positions can be electrically

hazardous. When crouching,

kneeling or at elevations, be sure to

insulate all conductive parts, wear

appropriate protective clothing, and

take precautions to prevent injury

from falls.

● Never attempt to use this equip-

ment at current settings or duty

cycles higher than those specified

on the equipment labels.

● Never use an electric arc welder to

thaw frozen pipes.

Flying

sparks

and hot metal can cause

injury. As welds cool, slag

can be thrown off. Take all

precautions described in this manual to

reduce the possibility of injury from

flying sparks and hot metal.

● Wear ANSI-approved (American

National Standards Institute-

approved) face shield or safety

glasses with side shield protection

when chipping or grinding metal

parts.

● Wear ear plugs when welding

overhead to prevent spatter or slag

from falling into ears.

Electric

arc

welding operations produce

intense light and heat and

ultraviolet (UV) rays. The

intense light and UV rays can cause

injury to eyes and skin. Take all

precautions described in this manual to

reduce the possibility of injury to eyes

and skin.

● All persons operating this

equipment or in the area while

equipment is in use must wear

protective welding gear including

welding helmet or shield with at

least a rating of shade 10, flame

resistant clothing, leather welding

gloves, and full foot protection.

Never look at arc

welding operations

without eye protection as described

above. Never use a shade filter lens

that is cracked, broken, or rated below

number 10. Warn others in the area not

to look at the arc.

Electric

arc

welding operations cause

sparks and heat metal to

temperatures that can cause

severe burns! Use protective gloves

WARNING

and clothing when performing any

metalworking operation. Take all

precautions described in this manual to

reduce the possibility of skin and

clothing burns.

● Make sure that all persons in the

welding area are protected from

heat, sparks, and ultraviolet rays.

Use additional face shields and

flame resistant barriers as needed.

● Never touch work pieces until

completely cooled.

Heat and

sparks

produced during electric arc

welding and other metal-

working operations can

ignite flammable and explosive

materials! Take all precautions

described in this manual to reduce the

possibility of flames and explosions.

● Remove all flammable materials

within 35 feet (10.7 m) of welding

arc. If removal is not possible,

tightly cover flammable materials

with fireproof covers.

● Do not operate any electric arc

welder in areas where flammable or

explosive vapors may be present.

● Take precautions to be sure that

flying sparks and heat do not cause

flames in hidden areas, in cracks,

behind bulkheads, etc.

Fire

hazard!

Do not weld on containers or

pipes that contain or have

contained flammable

materials or gaseous or liquid

combustibles.

Arc

welding

closed cylinders or containers

such as tanks or drums can

cause explosion if not

properly vented! Verify that any

cylinder or container to be welded has

an adequate ventilation hole, so that

expanding gases can be released.

Do not

breathe

fumes that are produced by

the arc welding operation.

These fumes are dangerous.

If the welding area cannot be

adequately ventilated, be sure to use

an air supplied respirator.

● Keep head and face out of welding

fumes.

● Do not perform electric arc welding

operations on metals that are

galvanized or cadmium-plated, or

that contain zinc, mercury or

beryllium without adhering to the

following precautions:

WARNING

General Safety

(Continued)

www.chpower.com

WARNING

Safe Practices For Occupational And

Educational Eye And Face

Protection

ANSI Standard Z87.1, from American

National Standards Institute, 1430

Broadway, New York, NY 10018

Refer to Material Safety Data Sheets

and manufacturer’s instructions for

metals, wire, coatings and cleaners.

Selecting the proper location can

significantly increase performance,

reliability and life of arc welder.

● For best results place welder in an

environment that is clean and dry.

Dust and dirt in the welder retain

moisture and increase wear of

moving parts.

● Place welder in an area that

provides at least 12” (30,48 cm) of

ventilation space at both front and

rear of unit. Keep all obstructions

away from this ventilation space.

● Store wire in a clean, dry location

with low humidity to preserve wire

coating.

● The receptacle used for welder must

be properly grounded and welder

must be the only load on power

supply circuit.

● The use of an extension cord is not

recommended for electric arc

welding machines. The voltage drop

in extension cord may significantly

degrade performance of welder.

Model WG4000

Welder components listed below

are in the wire feed compartment.

Open and remove.

Tools needed:

1/4”, 9/32”, 5/16” nut driver

#2 Phillips head driver

Mallet or hammer

After unpacking welder, you will find a

box at front surrounding attached

torch, ground clamp lead, and power

cord.

The box at the rear of the welder contains

parts to be assembled:

Wheels (2), axle (1), plastic hubs (2),

axle bolts (2), nuts (2) and washers

(2)

Front foot

Cylinder bracket and chain

Work clamp

Regulator, hose, and hose clamps

Spool of .035” flux core welding wire

a. Remove coating from base metal.

b. Make sure welding area is well

ventilated.

c. Use an air-supplied respirator.

Extremely toxic fumes are created

when these metals are heated.

The

electro-

magnetic field that is gener-

ated during arc welding may

interfere with the operation

of various electrical and electronic

devices such as cardiac pacemakers.

Persons using such devices should

consult with their physician prior to

performing any electric arc welding

operations.

● Route the wire feed gun and work

cables together and secure with

tape when possible.

● Never wrap arc welder cables

around body.

● Always position wire feed gun and

work leads so that they are on same

side of body.

● Exposure to electromagnetic fields

during welding may have other

health effects which are not known.

Always be sure

that the welding

area is secure and free of hazards

(sparks, flames, glowing metal or slag)

prior to leaving. Be sure that equip-

ment is turned off and excess wire is

cut off. Be sure that cables are loosely

coiled and out of the way. Be sure that

all metal and slag has cooled.

Cylin-

ders can

explode if damaged. Shield-

ing gas cylinders contain gas

under high pressure. If

damaged, a cylinder can explode. Since

gas cylinders are normally part of the

welding process, be sure to treat them

carefully.

● Protect compressed gas cylinders

from excessive heat, mechanical

shocks, and electric arcs.

● Install and secure cylinders in an

upright position by chaining them

to stationary support or equipment

cylinder rack to prevent them from

falling or tipping.

● Keep cylinders away from any

welding or other electrical circuits.

DANGER

WARNING

WG4000

● Never allow a welding electrode to

touch any cylinder.

● Use only correct shielding gas

cylinders, regulators, hoses, and

fittings designed for the specific

application; keep them and

associated parts in good condition.

● Turn face away from valve outlet

when opening cylinder valve.

● Keep protective cap in place over

valve except when cylinder is in use

or connected for use.

● Read and follow instructions on

compressed gas cylinders, associated

equipment, and CGA (Compressed

Gas Association) publication P-1

listed in Safety Standards.

Never use

flammable gases

with MIG welders. Only inert or non-

flammable gasses such as carbon

dioxide, argon, helium, or mixtures of

one or more of these gasses are

suitable for MIG welding.

Never lift cylinders

off the ground by

their valves, caps, or with chains or slings.

ADDITIONAL SAFETY STANDARDS

ANSI Standard Z49.1 from American

Welding Society, 550 N.W. LeJune Rd.

Miami, FL 33126

Safety and Health Standards

OSHA 29 CFR 1910, from

Superintendent of Documents, U.S.

Government Printing Office,

Washington, D.C. 20402

National Electrical Code

NFPA Standard 70, from National Fire

Protection Association, Batterymarch

Park, Quincy, MA 02269

Safe Handling of Compressed Gases

in Cylinders

CGA Pamphlet P-1, from Compressed Gas

Association, 1235 Jefferson Davis

Highway, Suite 501, Arlington, VA 22202

Code for Safety in Welding and

Cutting

CSA Standard W117.2, from Canadian

Standards Association, Standards Sales,

178 Rexdale Boulevard, Rexdale,

Ontario, Canada M9W 1R3

Cutting And Welding Processes

NFPA Standard 51B, from National Fire

Protection Association, Batterymarch

Park, Quicy, MA 02269

WARNING

DANGER

General Safety

(Continued)

Installation

Assembly

www.chpower.com

WARNING

WHEEL AND AXLE ASSEMBLY

1. Put one wheel on each end of axle

Using a mallet or hammer, drive a

plastic hub on axle ends to secure

wheels.

2. Align holes in axle assembly with

holes in base plate at rear of welder.

Secure with two bolts, washers, and

nuts.

FOOT ASSEMBLY

1. Remove four screws in bottom panel

near the front of the welder.

2. Align holes in metal foot with holes

on bottom of welder at front.

3. Secure foot with four screws

removed in step 1.

CYLINDER BRACKET ASSEMBLY

1. At back of welder, halfway down

each side, are two screws. Remove

both pairs of screws. Also remove the

screw in center of back panel.

2. Insert cylinder bracket between sides

of the welder and its black back,

aligning its holes with those in sides

of welder. Make sure bracket has

chain slots up.

3. Attach the bracket with the five

screws removed in Step 1.

WORK CLAMP ASSEMBLY

1. Loosen hex nuts on work clamp.

2. Insert cord through clamp handle and

slide bare wire under clamping block.

Tighten hex nuts, making sure bare

wire is clamped securely (Figure 3).

WIRE INSTALLATION

When the welder is

on and the gun

switch is activated, electric power may

be present in the output terminals,

feed roll, work clamp, gun cable

connection and welding wire. Do not

touch these parts when the welder is

on.

Wire Feed Arc Welder

NOTE: Before installing welding wire,

be sure that its diameter matches the

diameter of the groove in the drive

roller on the wire feed mechanism and

that the wire matches the contact tip in

the end of the gun. Any mismatch

could cause the wire to slip or bind.

1. Verify that welder is off. Open panel

on welder to expose wire feed

mechanism.

2. Remove spool lock by pushing in and

rotating it a 1/4 turn counterclockwise.

The knob, spring, and spool spacer can

now be removed. (See Figure 4).

NOTE: Spool spacer and spindle spacer

act as an 8” spool adapter. Purchase of

an adapter is not necessary.

3. Loosen wire feed tensioning screw

on drive mechanism. This allows

initial feeding of wire into gun liner

by hand.

4. Place wire spool on spindle so that

wire will come off spool on the end

closest to wire feed guide tube. Do

not cut wire loose yet. Install spool

spacer, spring, and spool lock by

pushing in and turning knob 1/4

rotation clockwise.

5. Hold wire and cut wire end from

spool. Do not allow wire to

unravel. Be sure that end of wire is

straight and free of burrs.

6. Feed wire through wire feed guide

tube, over groove in drive roll and into

gun liner. Tighten wire feed tensioning

screw so that it is snug. Do not

overtighten.

7. Remove torch nozzle by turning

counterclockwise. Unscrew contact

tip from end of welding torch (See

Figure 5). Plug welder into proper

power supply receptacle.

HINT: Keep torch cable straight when

feeding wire.

8. Turn on welder and set wire speed

rate to 5. Activate the gun switch

until wire feeds out past torch end.

Turn welder off.

Assembly

(Continued)

www.chpower.com

Clamping

Block

Figure 3 - Work Clamp Assembly

Torch Neck

Contact Tip

Nozzle

Figure 5 - Torch Nozzle

Figure 2 - WG4000 Assembly

Figure 4 - Weld Wire Routing

Bolt

Washer

Nut

Axle

Plastic

hub

Wheel

Hex Nuts

Cord

Foot

assembly

Bolt

Cylinder

chain

Cylinder

bracket

WARNING

WG4000

9. Carefully slip contact tip over wire

and screw it into torch neck. Install

nozzle by turning clockwise (See

Figure 5). Cut wire off approximately

1/4” from end of nozzle.

POLARITY

Polarity must be set to match the type

of welding process you wish to use.

MIG wire welding with bottled

shielding gas uses DCEP (DC electrode

positive). Flux-core wire welding with

no gas bottle requires DCEN (DC

electrode negative).

The WG4000 features easy-change

polarity posts located inside the top

section, next to the wire drive deck.

The positive (+) post is farthest from

the drive deck and has a red knob and

base. The negative post is closest to the

drive deck and has a black knob and

base.

Both leads have spade ends with holes

to go over the polarity posts. Turn the

polarity knob counterclockwise to

remove. Slip the end of the

appropriate lead over the post. Then

replace the polarity knob on the post

and tighten securely, turning clockwise.

These connections must be tight to

prevent overheating.

DUTY CYCLE / THERMOSTATIC

PROTECTION

Welder duty cycle is the percentage of

actual weld time that can occur in a ten

minute interval. For example, at a 10%

duty cycle, actual welding can occur for

one minute. Then the welder must cool

for nine minutes.

Internal components of this welder are

protected from overheating with an

automatic thermal switch. A yellow

lamp is illuminated on the front

panel if the duty cycle is exceeded.

Welding operations may continue

when the yellow lamp is no longer

illuminated.

MODEL WT1000

1. Remove lens retainer from face shield

with a regular screwdriver by prying

against shield and post of lens

retainer.

2. Remove protective film covering from

both sides of each lens cover. Put one

clear lens cover on each side of the

shaded lens. Place these three lenses

together in face shield and secure

with lens retainer. The lens retainer

should snap into second notch in face

shield.

3. Position one of the holes in

adjustment arm over the pins which

are located in the ear area of face

shield. These adjustment arms control

the closeness of fit and can be easily

repositioned if necessary.

4. Position headgear inside face shield.

Assemble helmet by inserting stud

screw through headgear and shield

into tension nut as shown. Do not

tighten tension nut completely.

5. Trial fit the welding helmet. Adjust

headgear ratchet band to a

comfortable position and lower face

shield. If shield is too far or too close

to face, use a different hole in

adjustment arm. Adjust tension nuts

so that helmet can be easily lowered

over the face by nodding the head.

1. Cut two plastic bolts and one nut

from handle. Trim excess plastic to

remove sharp edges.

2. Insert handle into slot and rotate 90

degrees to align handle stud with

hole in shield. Secure stud with

plastic nut.

3. Fold the top into position and then

one of the sides. Snap the two pins

into the holes. Press until you hear an

audible click, assuring complete

assembly. Repeat for the other side.

4. Install the shaded lens and secure

with the two plastic bolts. Tighten

securely, but do not overtighten as

this may damage the lens.

NOTE: If you have never welded before

or have little experience, a full-face

helmet is recommended. Both hands

are needed to stabilize and control the

angle and arc length of the torch.

Improper handling

and maintenance of

compressed gas cylinders and

regulators can result in serious injury

or death! Always secure gas cylinders

to the tank bracket kit, a wall or other

fixed support to prevent the cylinder

from falling over. Read, understand,

and follow all the warnings relating to

compressed gases and equipment

hazards in the safety instructions.

DANGER

Assembly

(Continued)

Figure 7

Headgear

Face Shield

Shaded Lens

Clear Lens Cover (2)

Post

Lens Retainer

Adjustment

Arm (2)

Tension Nut (2)

Stud Screw (2)

Welding Helmet

Assembly

(PROMOTIONAL MODELS ONLY)

www.chpower.com

Contact Tip Markings

Wire Size mm

.024” or .6

.030” or .8

.035” or .9

.040” or 1.0

Torch Work

Mig + —

Flux —

Figure 6

Shielding Gas

Installation

Work Cable

Torch

Cable

Handshield

Assembly

Figure 8

Wire Feed Arc Welder

NOTE: Shielding gas is not required if

flux-cored welding wire is used.

GAS TYPES

There are 3 types of gas generally used

for gas metal arc welding; 100% argon,

a mixture of 75% argon and 25%

carbon dioxide (C25) or 100% carbon

dioxide. The 75/25 mixture is

recommended for general steel

welding. For aluminum welding, use

100% argon. Cylinders of each type gas

may be obtained at your local welding

supply outlet. Secure cylinder in place

on your welding machine or other

support to prevent the cylinder from

falling over.

NOTE: Use of incorrect gas may lead to

little or no penetration of welding

bead.

REGULATOR

The regulator provides a constant

shielding gas pressure and flow rate

during the welding process. Each

regulator is designed to be used with a

specific gas or mixture of gases. The

argon and argon mixture use the same

thread type. The 100% carbon dioxide

uses a different thread type. An adapter

is included with this unit to change

between the two.

HOOKUP PROCEDURE

Cylinder gas is

under high

pressure. Point cylinder outlet away

from yourself and any bystanders

before opening.

1. A 20 cubic ft bottle fits this unit.

2. With cylinder securely installed,

remove cylinder cap, stand to side of

the cylinder opposite outlet, and

open the valve slightly, turning

counterclockwise. When gas is

emitted from the cylinder, close valve

by turning clockwise. This will blow

out dust or dirt that may have

accumulated around valve seat.

3. Install regulator on cylinder valve,

keeping face of gauges in vertical

position. Tighten stem nut securely

to gas valve.

4. Install one end of gas hose on

fitting on rear of welder and the

other end to the fitting on the

regulator. Use hose clamps on each

connection. Make sure gas hose is

not kinked or twisted.

5. Once again, stand opposite cylinder

WARNING

outlet and slowly open cylinder

valve. Inspect for leaks in

connections.

6. Pull trigger on gun to allow gas to

flow. While trigger is pulled and gas

is flowing, adjust gas regulator to at

least 20 cfh (cubic feet per hour).

Release trigger.

7. Remember to close gas valve when

finished welding.

1. Prior to using this

equipment, read,

understand, and comply

with all precautions in the

General Safety section.

Also, read the entire section titled

Welding Guidelines.

2. Verify welder is off.

3. Verify that surfaces of metals to be

joined are free from dirt, rust, paint,

oil, scale or other contaminants.

These contaminants make welding

difficult and cause poor welds.

All persons

operating this

equipment or in the area

while equipment is in use

must wear protective welding gear

including eye protection with proper

shade, flame resistant clothing, leather

welding gloves and full foot

protection.

DANGER

Extremely toxic fumes are

created when zinc- or

cadmium-plated materials,

lead or galvanized items are heated,

welded or cut. Before working with any

of these materials, refer to the General

Safety section for instructions.

4. Connect work clamp to work piece

or workbench (if metal). Make sure

the contact is secure. Avoid surfaces

with paint, varnish, corrosion, or

non-metallic materials.

5. Position Heat Selector on front

panel to desired setting.

See application decal inside door of

wire feed compartment for proper

heat settings.

NOTE: These settings are general

guidelines only. Heat setting may vary

according to welding conditions and

materials.

6. Rotate Wire Speed Control to

setting number 5. Then adjust as

needed after test weld is completed.

7. Plug input cord into a proper

voltage receptacle with proper

circuit capacity (20 amps minimum).

8. Switch welder ON.

9. Verify that the wire is extended

1/4” from the contact tip. If not,

squeeze trigger to feed additional

wire, then release trigger, and then

cut wire to proper length.

WARNING

Operation

MANUAL

Shielding Gas

Installation (Continued)

www.chpower.com

Figure 9 - Hookup

ARGON OR

ARGON MIX

INSTALLATION

Adapter

Cap

WG4000

10. Position wire feed gun near work

piece, and then lower the welding

helmet by nodding the head or

positioning hand shield. Then

squeeze gun trigger. Adjust heat

setting and wire speed as needed.

11. When finished welding, turn welder

off and store properly.

Disconnect power

supply and turn

welder off before inspecting or

servicing any components. Keep the

wire compartment cover closed at all

times unless the wire needs

replacement.

Before every use:

1. Check condition of weld cables and

immediately repair or replace any

cables with damaged insulation.

2. Check condition of power cord and

immediately repair or replace any

cord if damaged.

3. Inspect condition of gun tip and

nozzle. Remove any weld slag.

Replace gun tip or nozzle if

damaged.

Do not operate this

welding machine

with cracked or missing insulation on

welding cables, wire feed gun, or

power cord.

WARNING

Maintenance

Welding Guidelines

General

This line of welding machines can

utilize the Flux Cored Arc Welding

(Gasless) process or the Gas Metal Arc

Welding (MIG) process. The weld must

be protected (shielded) from

contaminates in the air while it is

molten. The gasless process uses a

tubular wire with a flux material inside.

The flux creates a shielding gas when

melted. The MIG process uses inert gas

to shield the weld while molten.

When current is produced by a

transformer (welding machine) and

flows through the circuit to the weld

wire, an arc is formed between the end

of the weld wire and the work piece.

This arc melts the wire and the work

piece. The melted metal of the weld

wire flows into the molten crater and

forms a bond with the work piece as

shown (Figure 10).

Arc Welding Basics

Five basic techniques affect weld

quality. These are: wire selection, heat

setting, weld angle, wire speed, and

travel speed. An understanding of

these techniques is necessary for

effective welds.

HEAT SETTING

The correct heat involves the adjust-

ment of the welding machine to the

required setting. Heat or voltage is

regulated by a switch on the welder.

Operation

(Continued)

Slag

Weld

Wire

Flux

(Gasless

only)

Work Piece

Shielding

Gas

Contact

Tip

Crater

Nozzle

Figure 10 - Weld Components

Every 3 months:

1. Replace any unreadable safety

labels on the welder.

2. Use compressed air to blow all dust

and lint from the ventilation

openings.

3. Clean wire groove on drive roll.

Remove wire from feed mechanism

and remove screws from drive roll

housing. Use a small wire brush to

clean drive roll. Replace if worn or

damaged.

CONSUMER AND WEAR PARTS

The following parts require routine

maintenance:

• Wire feed drive roller

• Gun liner - replace if worn

• Nozzle/contact tips

• Wire - this welder will accept either

4” or 8” diameter spools. Welding wire

is susceptible to moisture and oxidizes

over time, so it is important to select a

spool size that will be used within

approximately 6 months. For mild steel

welding, AWS ER70S6 solid wire or

AWS E71T-GS flux-core wire is

recommended.

• Contact tips - use Campbell Hausfeld,

Tweco

, and other compatible tips.

• Nozzle - use Tweco

style or compatible

nozzle. Use Campbell Hausfeld nozzle

model WT5021 found at place of

purchase of welder, or use Tweco

style

nozzle (or compatible nozzle) found at

local welding supply store.

www.chpower.com

Call (800) 746-5641

for replacement parts.

Changing Wire Sizes

DRIVE ROLLER

There are two grooves in the Drive

Roller. The small groove is for .030"-

.035" (.8 mm-.9 mm) wire and the

other is for .045" (1.2 mm) wire.

Remove the roller cover and flip the

drive roll to choose the correct groove

(see Parts Breakdown).When using

.030"-.035" (.8 mm-.9 mm) aluminum

wire, an optional smooth groove drive

roller and Teflon

wire liner are needed.

Contact Campbell Hausfeld for more

information. Aluminum wire is very soft

and should not have the same tension

as Flux Core or MIG wire. When

tensioning aluminum wire down to the

Drive Roller, turn the tension screw

three full turns or until the Drive Roller

begins to grip the wire and feed it

through the torch cable.

CONTACT TIP

Make sure the contact tip size matches

the wire size. If the tip is too small,

there will be too much drag on the

wire. If the tip is too large, arcing will

occur inside the tip. This will burn the

tip or cause carbon deposits inside the

tip that insulate the tip from the wire.

The heat setting used depends on the

size (diameter) and type of wire,

position of the weld, and the thickness

of the work piece. Consult specif-

ications listed on the welder. It is

suggested that the welder practice with

scrap metal to adjust settings and

compare welds with Figure 12.

WIRE TYPE AND SIZE

The correct choice of wire type involves

a variety of factors, such as welding

position, work piece material type,

thickness and condition of surface to be

welded. The American Welding Society,

AWS, has set up certain requirements

for each type of wire.

FLUX-CORE WIRE

E - 7

- GS

Weld strength, times

10,000 psi

Welding positions (0

for flat or horizontal,

1 for any position)

Tubular flux core wire

Flux type

AWS E71T-GS or E71T-11 is

recommended for this welder.

SOLID WIRE

ER - 70

S - 6

Weld strength, times

1,000 psi

Solid wire

Wire composition

ER-70S6 is recommended for this

welder.

WELD ANGLE

Weld angle is the angle at which the

nozzle is held during the welding

process. Using the correct angle

ensures proper penetration and bead

formation. As different welding

positions and weld joints become

necessary, nozzle angle becomes an

increasingly important factor in

obtaining a satisfactory weld. Weld

angle involves two positions - travel

angle and work angle.

Travel angle is the angle in the line of

welding and may vary from 5º to 45º

Wire Feed Arc Welder

Welding Guidelines

(Continued)

from the vertical, depending on

welding conditions.

Work angle is the angle from hori-

zontal, measured at right angles to the

line of welding. For most applications, a

45º travel angle and 45º work angle is

sufficient. For specific applications,

consult an arc welding handbook.

WIRE SPEED

The wire speed is controlled by the

knob on the front panel. The speed

needs to be “tuned” to the rate at

which the wire is being melted in the

arc. Tuning is one of the most critical

functions in wire feed welding. Tuning

should be performed on a scrap piece

of metal the same type and thickness as

that to be welded. Begin welding with

one hand “dragging” the gun nozzle

across the scrap piece while adjusting

the wire speed with the other hand.

Too slow of speed will cause sputtering

and the wire will burn up into the

contact tip. Too fast a speed will also

cause a sputtering sound and the wire

will push into the plate before melting.

A smooth buzzing sound indicates the

wire speed is properly tuned. For

aluminum, wire speed is typically set

higher (7 - 9 speed range).

NOTE: Repeat the tuning procedure

each time there is a change in heat

setting, wire diameter or type, or work

piece material type or thickness.

TRAVEL SPEED

The travel speed is the rate at which

the torch is moved across the weld

area. Factors such as diameter and type

of weld wire, amperage, position, and

work piece material thickness all affect

the speed of travel necessary for

completing a good weld (See Fig. 12).

When the speed is too fast, the bead is

narrow and bead ripples are pointed as

shown. When the speed is too slow, the

weld metal piles up and the bead is

high and wide. For aluminum, travel

speed is typically faster.

SLAG REMOVAL (FLUX-CORE WIRE

ONLY)

Wear ANSI

approved safety

glasses (ANSI Standard Z87.1) and

protective clothing when removing

slag. Hot, flying debris can cause

personal injury to anyone in the area.

After completing the weld, wait for the

welded sections to cool. A protective

coating called slag now covers the weld

bead which prevents contaminants in

the air from reacting with the molten

metal. Once the weld cools to the point

that it is no longer glowing red, the

slag can be removed. Removal is done

with a chipping hammer. Lightly tap

the slag with the hammer and break it

loose from the weld bead. The final

clean-up is done with a wire brush.

NOTE: When making multiple weld

passes, remove the slag before each

pass.

WELDING POSITIONS

Four basic welding positions can be

used; flat, horizontal, vertical, and

overhead. Welding in the flat position

is easier than any of the others because

welding speed can be increased, the

molten metal has less tendency to run,

better penetration can be achieved,

and the work is less fatiguing. Welding

is performed with the wire at a 45º

travel angle and 45º work angle.

Other positions require different

techniques such as a weaving pass,

circular pass, and jogging. A higher skill

level is required to complete these

welds.

Overhead welding is the least desirable

position as it is the most difficult and

dangerous. Heat setting and wire

selection will vary depending upon the

position.

All work should be performed in the

flat position if possible. For specific

applications, consult an arc welding

technical manual.

WARNING

TRAVEL ANGLE

WORK ANGLE

5º - 45º

Figure 11 - Weld Angle

www.chpower.com

stainless steel brush to eliminate any

oxides on the weld and grounding

surface. 100% Argon must be used

when welding aluminum. If Argon is not

used, metal penetration is unlikely.

1. Verify that welder is OFF and power

cord disconnected.

2. Remove welder cover to expose the

ON/OFF switch.

WG4000

Normal Heat, Wire Speed, Travel

Speed

Heat Too Low

Heat Too High

Wire Speed Too Fast

Wire Speed Too Slow

Travel Speed Too Slow

Travel Speed Too Fast

Base Metal

Figure 12 - Weld Appearance

Figure 14 - Multiple Weld Passes

Welding Guidelines

(Continued)

WELD PASSES

Sometimes more than one pass is

necessary to fill the joint. The root pass

is first, followed by filler passes and

the cover pass. If the pieces are thick, it

may be necessary to bevel the edges

that are joined at a 60º angle.

NOTE: Remember to remove the slag

before each pass for gasless process.

PUSH VS PULL TECHNIQUE

The type and thickness of the work

piece dictates which way to point the

gun nozzle. For thin materials (18 gauge

and up) and all aluminum, the nozzle

should point out in front of the weld

puddle and push the puddle across the

workpiece. For thicker steel, the nozzle

should point into the puddle to increase

weld penetration. This is called

backhand or pull technique

(See Figure 15).

ALUMINUM WELDING

Any aluminum surface to be welded,

must be cleaned thoroughly with a

Figure 13 - Weld Passes

Cover

Filler

Root

3. Disconnect the black and white

power cord wires connected to the

ON/OFF switch.

4. Disconnect the green power cord

wire connected to welder frame.

5. Loosen the cord strain relief screw(s)

and pull cord out of strain relief.

6. Install new cord in reverse order.

PUSH

PULL

Figure 15

Supply Cable

Replacement

www.chpower.com

Troubleshooting Chart - Welder

Symptom Possible Cause(s) Corrective Action

1. Duty cycle exceeded

2. Poor work clamp connection

3. Defective power switch

4. Blown breaker or fuse

1. Wrong size gun tip

2. Gun liner clogged or

damaged

3. Gun tip clogged or damaged

4. Feed roller worn

5. Not enough tension

Slag inside gun nozzle

1. Poor contact

2. Using an extension cord with

excessive length

1. Wire jammed

2. Out of wire

3. Not enough tension

4. Wire liner worn

5. Wire disconnected internally

6. Contact tip clogged

1. Wire speed too slow

2. Travel speed too slow or heat

is too high

For Information About This Product, Call 1-800-746-5641

Bead is intermittently too

thin

Bead is intermittently too

thick

Ragged depressions at

edge of weld

Weld bead does not

penetrate base metal

Wire sputters and sticks

1. Fast and/or inconsistent travel speed

2. Output heat setting too low

1. Slow and/or inconsistent travel speed

2. Output heat setting too high

1. Travel speed too fast

2. Wire speed too fast

3. Output heat setting too high

1. Inconsistent travel speed

2. Output heat setting too low

3. No or low shielding gas

4. Wrong shielding gas (aluminum)

5. Extension cord is too long

6. (Aluminum) Possible oxide build-up on

surface

1. Damp wire

2. Wire speed too fast

3. Wrong type of wire

4. No or low shielding gas

1. Allow welder to cool until ON/OFF Switch lamp goes out

2. Be sure all connections are secure, and attaching surface is

clean

3. Replace switch

4. Reduce circuit load, reset breaker or replace fuse

1. Use proper size gun tip

2. Clean or replace gun liner

3. Clean or replace gun tip

4. Replace

5. Tighten tensioning screw

Clean slag from gun nozzle

1. Be sure all connections are secure, and attaching surface is

clean

2. Never use an extension cord longer than 20 ft

1. Reload wire

2. Replace wire spool

3. Tighten tensioning screws if wire is slipping

4. Replace liner

5. Call 1-800-746-5641 for assistance

6. Replace contact tip

1. Run speed in 7 - 10 range

2. Increase the travel speed or reduce heat settings

No output

Wire tangles at drive roller

Gun nozzle arcs to work

surface

Work clamp and/or cable

gets hot

Wire does not feed

(Aluminum) Wire burns back

into tip or (aluminum) metal

bubbles or burns through

Troubleshooting Chart - Welds

Symptom Possible Cause(s) Corrective Action

1. Decrease and maintain constant travel speed

2. Increase output heat setting

1. Increase and maintain travel speed

2. Reduce output heat setting

1. Decrease travel speed

2. Decrease wire speed

3. Reduce output heat setting

1. Decrease and maintain constant travel speed

2. Increase output heat setting

3. Use gas for MIG process or refill bottle

4. Use only 100% Argon gas

5. Never use an extension cord longer than 20 ft

6. Clean surface thoroughly with a stainless steel

brush only

1. Use dry wire and store in dry location

2. Reduce wire speed

3. Use flux core wire when not using gas

4. Use gas for MIG process or refill bottle

www.chpower.com

Limited 5-3-1 Warranty

1. Duration: The manufacturer warrants that it will repair, at no charge for parts or labor, the Welder, Welding Gun, or Cables, proven defective in material or

workmanship, during the following time period(s) after date of original retail purchase:

For 5 Years: The Welder Transformer and Rectifier

For 3 Years: The Entire Welder (excluding clamps, welding gun, electrode holder, cables, or accessories packed with welder)

For 1 Year: The Welding Clamps, MIG Gun, Electrode Holder, Accessories, and Welding Cables (as applicable)

2. Who Gives This Warranty (Warrantor):

The Campbell Group / A Scott Fetzer Company

100 Production Drive

Harrison, OH 45030

Telephone: (513)-367-4811

3. Who Receives This Warranty (Purchaser): The original purchaser of the Campbell Hausfeld product.

4. What is covered under this warranty: Defects in material and workmanship which occur within the duration of the warranty period. This warranty

extends to the Welder, the Welders Transformer and Rectifier, Welding Gun or Electrode Holder, and cables only.

5. What is not covered under this warranty:

A. Implied warranties, including those of merchantability and FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO THIS EXPRESS

WARRANTY. After this period, all risks of loss, from whatever reason, shall be on the purchaser. Some states do not allow limitations on how long an

implied warranty lasts, so above limitations may not apply to you.

B. ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT FROM ANY DEFECT FAILURE OR MALFUNCTION OF

THE CAMPBELL HAUSFELD PRODUCT. Some states do not allow limitations on how long an implied warranty lasts, so above limitations may not apply

to you.

C. This warranty does not apply to any accessory items included with the product which are subject to wear from usage; the repair or replacement of

these items shall be at the expense of the owner. These MIG items include but are not limited to; Contact Tips, Nozzles, Gun Liners, Drive Rollers, Felt

Wire Cleaner. In addition, this warranty does not extend to any damage caused by the untimely replacement or maintenance of any of the previously

listed CONSUMABLE parts.

D. Any failure that results from accident, purchaser’s abuse, neglect or failure to operate products in accordance with instructions provided in the owner’s

manual(s) supplied with the product.

E. Pre-delivery service, i.e. assembly and adjustment.

7. Responsibilities of Warrantor under this warranty: Repair or replace, at Warrantor’s option, products or components which have failed within duration

of the warranty period.

8. Responsibilities of purchaser under this warranty:

A. Deliver or ship the Campbell Hausfeld product or component to Campbell Hausfeld. Freight costs, if any, must be borne by the purchaser.

B. Use reasonable care in the operation and maintenance of the products as described in the owner’s manual(s).

9. When Warrantor will perform repair or replacement under this warranty: Repair or replacement will be scheduled and serviced according to the

normal work flow at the servicing location, and depending on the availability of replacement parts.

This Limited Warranty gives you specific legal rights and you may also have other rights which vary from state to state.

WG4000

www.chpower.com

WG4000 Wiring Diagram

Wire Feed Arc Welder

www.chpower.com

XXX

@ 127

OPENS

C2C1

COM

FAN~

DECK

A1L2

L2L1

OFF

GUN

DRIVE

BLACK

WHITE

GREEN

For Replacement Parts, call 1-800-746-5641

Address parts correspondence to:

The Campbell Group

Attn: Parts Department

100 Production Drive

Harrison, Ohio 45030 U.S.A.

Please provide following information:

- Model number

- Serial number

- Part description and number as

shown in parts list

WG4000

MODEL WG4000

www.chpower.com

** Contact Tip (See chart on Page 14)

41 & 42

(inside)

7 & 9

39 & 40

***

8 & 10

1 Warning decal - 1 pc Italy DK670100AV 1

2 Ground clamp - large (Cord not included) WC100100AV 1

3 Welding cable 6 AWG (6 ft) ❋ 1

4 Strain relief WC102000AV 2

5 Handle WC301700AV 1

6 Power cord 12AWG/3C (10 ft) Type ST with 230V, 50A Plug ❋ 1

7 Wire speed control knob WC400201AV 1

8 Switch knob WC400401AV 1

9 Wire speed control PCB ▲ WC401700AV 1

10 Power switch ▲ WC401800AV 1

11 Capacitor - 15,000 µF ▲ WC401900AV 2

12 Drive deck assembly (Includes nos. 13-18) WC500400AV 1

13 Tension screw WC500002AV 1

14 Tension spring WC500003AV 1

15 Roller cover WC500004AV 1

16 Swing arm WC500005AV 1

17 Drive roller - 0.8-1.2 mm WC500006AV 1

Optional drive roller - 0.6-0.9 mm▲ WC500001AV ✤

18 Swing arm roller WC500007AV 1

19 Spool lock WC500100AV 1

20 Spindle spring WC500101AV 1

21 Spool adapter WC500200AV 1

22 Spindle WC500300AV 1

23 Torch ring WC600009AV 1

24 Torch assembly - Universal WC600900AJ 1

25 Hanger clip WC600003AV 1

26 Torch handle - 2 pc WC600201AV 1

27 Trigger WC600202AV 1

28 Contact spring WC600203AV 1

29 Gas valve WC600204AV 1

30 Trumpet liner - 5.75” WC600305AV 1

31 Swan neck w/ diffuser (Tweco®) WC600701AV 1

32 Wire liner - coated metal WC600209AV 1

33 Nozzle, Tweco® style WT502100AJ 1

34 Wheel WC701300AV 2

35 Front foot WC702300AV 1

36 Cylinder bracket WC702400AV 1

37 Axle WC703200AV 1

38 Wheel cap WC703400AV 2

39 Polarity cap - red ▲ WC704000AV 1

40 Polarity cap - black ▲ WC704100AV 1

41 Hose barb - external ▲ WC802300AV 1

42 Hose barb - internal ▲ WC802400AV 1

43 Cylinder chain WC802700AV 1

44 Handshield (lens not included) ▲ WC801600AV 1

45 Shaded lens (for handshield) ▲ WC801100AV 1

46 Welding helmet (promotional models only) ▲ WT100000AV 1 or 0

47 Replacement lens kit - one shaded and two clear ▲ WT110501AV ✤

48 Optional aluminum welding kit (includes Teflon® wire liner, smooth-

groove drive roller and 4 .030" (.8 mm) aluminum contact tips ▲ WT253000AV ✤

49 Argon regulator with 2 gauges ▲ WC803200AV 1

50 Adapter - Argon regulator/CO

cylinder ▲ WC803300AV 1

❋ Standard hardware item available at hardware store or welding supply store

▲ Not shown

✤ Optional accessory, sold separately

Replacement Parts List - Model WG4000

Ref

No. Description Part Number Qty

***OPTIONAL WIRE

Part Number Part Number

Type Description (2 pounds) (10 pound)

Flux E71T-GS .030” WE200001AV WE201000AV

Flux E71T-GS .035” WE200501AV WE201500AV

MIG ER70S6 .024” WE300001AV WE301500AV

MIG ER70S6 .030” WE300501AV WE302000AV

MIG ER70S6 .035” WE301001AV WE302500AV

Aluminum MIG ER5356 .030” WE303001AV (1 lb.) N/A

Wire Feed Arc Welder

www.chpower.com

**OPTIONAL CONTACT TIPS (4/package)

Size

mm in. Part Number

0.6 0.024 WT501200AJ

0.8 0.030 WT501300AJ

0.9 0.035 WT501400AJ

Glossary of Welding Terms

AC or Alternating Current - electric

current that reverses direction

periodically. Sixty cycle current travels

in both directions sixty times per

second.

Arc Length - the distance from the

end of the electrode to the point

where the arc makes contact with the

work surface.

Base Metal - the material to be

welded.

Butt Joint - a joint between two

members aligned approximately in the

same plane.

Crater - a pool, or pocket, that is

formed as the arc comes in contact with

the base metal.

DC or Direct Current - electric current

which flows only in one direction. The

polarity (+ or -) determines which

direction the current is flowing.

DC Reverse Polarity - occurs when

the electrode holder is connected to

the positive pole of the welding

machine. Reverse Polarity directs more

heat into melting the electrode rather

then the work piece. It is used on

thinner material.

DC Straight Polarity - occurs when

the electrode holder is connected to

the negative pole of the welding

machine. With straight polarity more

heat is directed to the work piece for

better penetration on thicker material.

Electrode - a coated metal wire having

approximately the same composition as

the material being welded.

Fillet Weld - approximately a triangle

in cross-section, joining two surfaces at

right angles to each other in a lap, T or

corner joint.

Flux - a coating, when heated, that

produces a shielding gas around the

welding area. This gas protects the

parent and filler metals from impurities

in the air.

Flux Cored Arc Welding (FCAW) -

also called Gasless, is a welding process

used with a wire-feed welding

machine. The weld wire is tubular with

flux material contained inside for

shielding.

Gas Metal Arc Welding (GMAW) -

also called MIG, is a welding process

used with a wire feed welding

machine. The wire is solid and an inert

gas is used for shielding.

Gas Tungsten Arc Welding (GTAW) -

also called TIG, is a welding process

used with welding equipment with a

high frequency generator. The arc is

created between a non-consumable

tungsten electrode and the work piece.

Filler metal may or may not be used.

Lap Joint - a joint between two

overlapping members in parallel

planes.

Open Circuit Voltage (OCV) - the

voltage between the electrode and the

work clamp of the welding machine

when no current is flowing (not

welding). The OCV determines how

quickly the arc is struck.

Overlap - occurs when the amperage is

set too low. In this instance, the molten

metal falls from the electrode without

actually fusing into the base metal.

Porosity - gas pockets, or cavities,

formed during weld solidification. They

weaken the weld.

Penetration - the depth into the work

piece that has been heat effected by

the arc during the welding process. A

good weld achieves 100% penetration

meaning that the entire thickness of

the work piece has been heated and

resolidified. The heat effected area

should be easily seen on the opposite

side of the weld.

Shielded Metal Arc Welding

(SMAW) - also called Stick, is a welding

process with uses a consumable

electrode to support the arc. Shielding

is achieved by the melting of the flux

coating on the electrode.

Slag - a layer of flux soot that protects

the weld from oxides and other

contaminants while the weld is

solidifying (cooling). Slag should be

removed after weld has cooled.

Spatter - metal particles thrown from

the weld which cool and harden on the

work surface. Spatter can be minimized

by using a spatter resistant spray on the

work piece before welding.

Tack Weld - weld made to hold parts

in proper alignment until final welds

are made.

Travel Angle - the angle of the

electrode in the line of welding. It

varies from 5º to 45º depending on

welding conditions.

T Joint - made by placing the edge of

one piece of metal on the surface of

the other piece at approximately a 90º

angle.

Undercut - a condition that results

when welding amperage is too high.

The excessive amperage leaves a

groove in the base metal along both

sides of the bead which reduces the

strength of the weld.

Weld Pool or Puddle - a volume of

molten metal in a weld prior to its

solidification as weld metal.

Weld Bead - a narrow layer or layers of

metal deposited on the base metal as

the electrode melts. Weld bead width is

typically twice the diameter of the

electrode.

Work Angle - the angle of the

electrode from horizontal, measured at

right angles to the line of welding.

www.chpower.com

WG4000

Notes

Wire Feed Arc Welder

www.chpower.com

l’électrode négative à courant

continu (DCEN).

Danger

indique :

Ne pas suivre cet avertissement causera

la perte de vie ou blessures graves.

Aver-

tissement

indique : Ne pas suivre cet avertis-

sement peut causer la perte de vie ou

blessures graves.

Attention

indique :

Ne pas suivre cet avertissement peut

causer des blessures (légères ou

moyennes) ou dommage matériel.

REMARQUE: Remarque indique :

Information additionnelle concernant

le produit ou son utilisation.

ATTENTION

AVERTISSEMENT

DANGER

2. Pistolet d’alimentation en fil

avec buse de 0,035.

3. Cordon d’alimentation -

brancher dans une prise de courant

230 V.

4. Interrupteur de sélection

Marche/Arrêt/Chaleur - Pour

choisir la puissance du soudeur. Six

sélections sont possibles.

5. Commande de réglage de

vitesse de fil infini - tourner dans

le sens des aiguilles d’une montre

pour augmenter la vitesse de fil et

tourner dans le sens inverse des

aiguilles d’une montre pour réduire

la vitesse du fil.

6. Branchement de polarité (à

l’intérieur du boîtier

d’alimentation du fil) - Fournit

les connexions du MIG, de

l’électrode positive à courant

continu (DCEP); et du fil fourré, de

Ce soudeur à l’arc alimenté en fil

Campbell Hausfeld est conçu pour un

courant monophasé standard de 230

volts. Ces soudeurs sont équipés d’un

réglage de vitesse de fil infini pour la

sélection précise de taux d’alimentation

en fil convenable à une variété de

conditions de soudage. Les pièces

internes sont protégées d’un

thermostat.

Ces soudeurs sont conçus pour

l’utilisation avec les méthodes de

Soudage À L’Arc Fourré De Flux (sans

gaz) ou le Soudage Au Chalumeau

(Mig). Ce soudeur, livré de l’usine peut

souder avec un fil de 0,8 mm à 1,2 mm

de diamètre. Une bobine de fil fourré

de flux et une buse de 0,035 po (0,9

mm) sont comprises.

Déballage

Quelques pièces détachées du

soudeur peuvent être situées dans

le compartiment d’alimentation en

fil. Lors du déballage, l’examiner

soigneusement pour toute trace de

dommage susceptible de s’être produit

en cours de transport. S’il y a des pièces

endommagées ou manquantes,

composer le (800) 746-5641.

Exigences De Circuit

Cet

équipe-

ment exige un circuit réservé de 230

volts, minimum 20 ampères. Ne pas

faire fonctionner les appareils

électroménagers, les lampes ou les

outils sur ce circuit pendant

l’utilisation de cet équipement. Les

rallonges ne sont pas recommandées.

Le non-respect de ces directives peut

causer des fusibles sautés et des

disjoncteurs déclenchés.

Commandes et Pièces

Détachées

1. Pince de Soudeur - fixer à l’objet

de travail.

ATTENTION

Instructions D’Utilisation & Manuel De Pièces De Rechange Modèle WG4000

Need

Assistance?

Call Us First!

1-800-746-5641

Description

17 Fr

Généralités Sur La Sécurité

IN970800AV 3/03

Figure 1

FLUX

CORE

MIG

Pistolet d’alimentation

en fil (2)

Pince de

Soudeur (1)

Cordon

d’alimentation (3)

Commande de

réglage de vitesse

de fil infini (5)

Branchement de polarité (6)

Interrupteur de sélection

Marche/Arrêt/Chaleur (4)

Soudeur À L’Arc

Alimenté En Fil

S’il vous plaît lire et conserver ces instructions. Lire attentivement avant de monter, installer, utiliser ou de procéder à l’entretien du produit

décrit. Se protéger ainsi que les autres en observant toutes les instructions de sécurité, sinon, il y a risque de blessure et/ou dégâts matériels!

Conserver ces instructions comme référence.

MODEL WG4000

MÉMENTO: Gardez votre preuve datée d'achat à fin de la garantie!

Joignez-la à ce manuel ou classez-la dans un dossier pour plus de sécurité.

BUILT TO LAST

18 Fr

Toujours avoir un extincteur

d’incendie disponible pendant

le soudage à l’arc.

● Lire et comprendre toutes les

instructions avant de démarrer un

soudeur à l’arc ou de procéder à son

entretien. Ne pas suivre les

précautions et instructions de sécurité

peut mener à des dommages à

l’équipement et/ou à des blessures

graves, perte de vie.

● L’installation, l’entretien, la réparation

et ;’utilisation de cet équipement

doivent être effectués par des

personnes qualifiées conformément

aux codes nationaux, provinciaux et

locaux.

L’utilisation incorrecte des

soudeurs à l’arc électriques

peut causer des chocs

électriques, blessures et perte de vie.

Suivre toutes les précautions indiquées

dans ce manuel afin de réduire le

risque de choc électrique.

● S’assurer que toutes les pièces

détachées du soudeur à l’arc soient

propres et en bon état avant d’utiliser

le soudeur. S’assurer que l’isolation

sur tous les câbles, pistolets

d’alimentation en fil et cordons

d’alimentation ne soit pas

endommagée. Toujours réparer ou

remplacer les pièces détachées

endommagées avant d’utiliser le

soudeur. Toujours garder les

panneaux, écrans de soudage, etc. en

place pendant l’utilisation du

soudeur.

● Toujours porter des vêtements

protecteurs et gants de soudage

secs ainsi que des chaussures

isolantes.

● Toujours faire fonctionner le

soudeur dans un endroit propre, sec

et bien ventilé. Ne jamais utiliser un

soudeur dans un endroit humide,

trempe, pluvieux ou mal-ventilé.

● S’assurer que l’objet sur lequel vous

travaillez soit bien fixé et mis à la

terre correctement avant de com-

mencer le soudage électrique à l’arc.

● Le câble de soudage roulé devrait

être étendu avant l’utilisation afin

d’éviter le surchauffage et le

dommage à l’isolation.

Ne jamais

immerger

DANGER

AVERTISSEMENT

le fil ni le pistolet dans l’eau. Si le

soudeur devient trempe, il est

nécessaire qu’il soit complètement sec

et propre avant l’utilisation!

● Toujours mettre l’équipement hors

circuit et le débrancher avant de le

déplacer.

● Toujours brancher le conducteur de

travail en premier lieu.

● Vérifier que l’objet de travail soit

mis à la terre correctement.

● Toujours mettre l’équipement de

soudage électrique à l’arc hors

circuit s’il nest pas en usage et

couper l’excès de fil du pistolet.

● Ne jamais permettre que votre corps

touche le fil fourré et la terre ni

l’objet de travail mis à la terre

simultanément.

● Les conditions et positions de

soudage difficiles peuvent poser des

dangers électriques. Si vous êtes

accroupi, à genoux ou surélevé,

s’assurer que toutes les pièces

conductrices soient isolées. Porter des

vêtements protecteurs convenables et

prendre des précautions contre les

chutes afin d’éviter des blessures.

● Ne jamais esayer d’utiliser cet

équipement au délà des réglages de

courant ou des facteurs d’utilisation

indiqués sur les étiquettes.

● Ne jamais utiliser un soudeur

électrique à l’arc pour dégeler les

tuyaux congelés.

Les étincelles volantes et le

métal chaud peuvent causer

des blessures. La scorie peut

s’échapper pendant le refroidissement

des soudures. Suivre toutes les

directives et précautions indiquées

dans ce manuel pour réduire la

possibilité de blessures causées par les

étincelles volantes et le métal chaud.

● Porter un masque de soudeur

approuvé par ANSI ou des lunettes

protectrices avec écrans protecteurs

de bords pendant le burinage ou

l’ébarbage des pièces en métal.

● Utiliser des protège-tympans pour le

soudage aérien afin d’éviter que la

scorie ou la bavure tombe dans les

oreilles.

Le soudage électrique à l’arc

produit une lumière et une

chaleur intenses et des rayons

ultaviolets (UV). Cette lumière intense

et ces rayons UV peuvent causer des

blessures aux yeux et à la peau.

Prendre toutes les précautions

indiquées dans ce manuel afin de

réduire la possibilité de blessures aux

AVERTISSEMENT

yeux et à la peau.

● Toutes les personnes qui utilisent cet

équipement ou qui sont présentes là

où l’équipement est utilisé doivent

porter des vêtements de soudage

protecteurs y compris : masque ou

casque de soudeur ou écran avec une

lentille filtrante de classification d’au

moins 10, vêtements incombustibles,

gants de soudeur en cuir et protection

complète pour les pieds.

Ne jamais

observer

le soudage sans la protection pour les

yeux indiquée ci-dessus. Ne jamais

utiliser une lentille filtrante qui est

fendue, cassée, ou classifiée moins que

10. Avertir les autres personnes

présentes de ne pas regarder l’arc.

Le soudage électrique à l’arc

produit des étincelles et

chauffe le métal aux

températures qui peuvent causer des

brûlures graves ! Utiliser des gants et

vêtements protecteurs pendant

n’importe quel travail de métal.

Prendre toutes les précautions

indiquées dans ce manuel afin de

réduire la possibilité de brûlures de

peau ou de vêtements.

● S’assurer que toutes les personnes

dans l’endroit de soudage soient

protégées contre la chaleur, les

étincelles et les rayons ultraviolets.

Utiliser des écrans de visage

additionnels et écrans coupe-feu là

où c’est nécessaire.

● Ne jamais toucher les objets de

travail avant qu’ils se refroidissent

complètement.

La chaleur et les étincelles

qui sont produites pendant le

soudage électrique à l’arc et

autres travaux de métal peuvent

allumer les matériaux inflammables et

explosifs ! Prendre toutes les

précautions indiquées dans ce manuel

afin de réduire la possibilité de flammes

et d’explosions.

● Enlever tous les matériaux

inflammables à moins de

10,7 mètres (35 pieds) de l’arc de

soudage. Si ceci n’est pas possible,

couvrir les matériaux inflammables

avec des couvertures incombustibles.

● Ne pas utiliser de soudeur électrique

à l’arc dans les endroits qui

contiennent des vapeurs

inflammables ou explosives.

● Prendre toutes les précautions pour

s’assurer que les étincelles volantes

et la chaleur ne produisent pas de

flammes dans des endroits cachés,

fentes, à l’arrière des cloisons, etc.

AVERTISSEMENT

Généralités Sur La

Sécurité

(Suite)

Soudeur À L’Arc Alimenté En Fil

19 Fr

NORMES DE SÉCURITÉ

ADDITIONNELLES

Norme ANSI Z49.1 de l’ American

Welding Society, 550 N.W. LeJune Rd.

Miami, FL 33126

Safety and Health Standards

(Normes de Sécurité et de Santé)

OSHA 29 CFR 1910, du Superintendent

of Documents, U.S. Government

Printing Office, Washington, D.C. 20402

National Electrical Code (Code

Électrique National)

Norme NFPA 70, du National Fire

Protection Association, Batterymarch

Park, Quincy, MA 02269

Safe Handling of Compressed Gases

in Cylinders (Manipulation Sûr des

Gaz Comprimés en Cylindres)

CGA Pamphlet P-1, du Compressed Gas

Association, 1235 Jefferson Davis

Highway, Suite 501, Arlington, VA

22202

Code for Safety in Welding and

Cutting (Code de Sécurité pour le

Soudage et le Coupage)

Norme CSA W117.2, du Canadian

Standards Association, Standards Sales,

178 Rexdale Boulevard, Rexdale,

Ontario, Canada M9W 1R3

Cutting And Welding Processes

(Procédés de Coupage et de

Soudage)

Norme NFPA 51B, du National Fire

Protection Association, Batterymarch

Park, Quicy, MA 02269

Safe Practices For Occupational And

Educational Eye And Face

Protection (Règlements

Professionnels et D’Éducation de

Sécurité pour la Protection des

Yeux et du Visage)

Norme ANSI Z87.1, de l’American

National Standards Institute, 1430

Broadway, New York, NY 10018

Se référer aux fiches signalitéques de

sécurité du produit et aux instructions

du fabricant de métaux, électrodes,

enduits et produits pour le nettoyage.

Choisir le bon endroit peut augmenter

le rendement, la sécurité de

fonctionnement et la vie du soudeur à

l’arc.

● Pour un meilleur résultat, placer le

soudeur dans un endroit propre et

sec. La poussière et la saleté

absorbent l’humidité dans le

soudeur et augmentent l’usure des

pièces mobiles.

● Placer le soudeur dans un endroit qui

fournit au moins 12 po (305 mm)

Risque d’incendie ! Ne pas

souder les récipients ni les

tuyaux qui contiennent ou

ont contenu des matériaux

inflammables ou combustibles gazeux

ou liquides.

Le soudage à l’arc des

cylindres ou récipients fer-

més tels que les réservoirs

ou bidons peuvent causer une

explosion s’ils ne sont pas bien ventilés

! Vérifier qu’il y ait un trou de

ventilation suffisant dans n’importe

quel cylindre ou récipient pour

permettre la ventilation des gaz en

expansion.

Ne pas respirer les vapeurs

qui sont produites par le

soudage à l’arc. Ces vapeurs

sont dangereuses. Utiliser un

respirateur si l’endroit de soudage n’est

pas bien ventilé.

● Garder la tête et le visage hors des

vapeurs de soudage.

● Ne pas exécuter le soudage

électrique à l’arc sur les métaux qui

sont galvanisés ou plaqués en

cadmium, ou qui contiennent le

zinc, le mercure, ou le beryllium sans

suivre les précautions suivantes:

a. Enlever l’enduit du métal commun.

b. S’assurer que l’endroit de soudage

soit bien ventilé.

c. Utiliser un respirateur à air fourni.

Des vapeurs extrêmement toxiques

sont produites pendant le chauffage

de ces métaux.

Le champ électromagnétique

qui est produit pendant le

soudage à l’arc peut causer de

l’interférence avec le fonctionnement

de plusieurs appareils électriques tels

que les pacemakers cardiaques. Toutes

les personnes qui utilisent ces appareils

doivent consulter leur médecin avant

d’exécuter le soudage électrique à l’arc.

● Acheminer l’électrode et les câbles

ensemble et les fixer avec du ruban

adhésif là où c’est possible.

● Ne jamais envelopper les câbles de

soudage à l’arc autour de votre

corps.

● Toujours placer l’électrode et les

conducteurs de terre afin qu’ils

soient sur le même côté du corps.

● L’exposition aux champs

électromagnétiques peut avoir

AVERTISSEMENT

autres réactions inconnues

concernant la santé.

Toujours

s’assurer

que l’endroit de soudage soit sans

danger et sans risques (étincelles,

flammes, métal chauffé au rouge ou

scorie) avant de partir. S’assurer que

l’équipement soit hors circuit et que le

surplus de fil soit coupé. S’assurer que

les câbles soient roulés (sans serrer) et

hors du chemin. S’assurer que tout

métal et scorie soient refroidis.

Les bouteilles peuvent

exploser si endommagées.

Elles contiennent du gaz sous

haute pression. Si elles sont

endommagées, elles peuvent exploser.

Puisque les bouteilles de gaz font

partie du processus de soudage,

s’assurer de bien les respecter.

● Protéger les bouteilles de gaz

comprimé contre la chaleur

excessive, les chocs mécaniques, et

les arcs.

● Installer et fixer les bouteilles dans

une position verticale en utilisant

une chaîne sur un support

stationnaire ou un support de

bouteille pour éviter le

renversement ou le basculage.

● Garder les bouteilles à l’écart du

soudage ou autres circuits

électriques.

● Ne jamais permettre que l’électrode

de soudage touche une bouteille.

● Utiliser seulement les bouteilles de

gaz corrects; régulateurs, tuyaux et

raccords conçus pour votre

application et les tenir en bon état

de marche.

● Tourner le visage loin de la soupape

d’échappement en ouvrant la

soupape de la bouteille.

● Garder le chapeau protecteur en

place sur la soupape sauf si la

bouteille est en service ou branchée

pour le service.

● Lire et suivre les instructions pour

les bouteilles de gaz et autre

équipement et la publication P-1 de

CGA indiquée dans les Normes de

Sécurité.

Ne jamais

utiliser

les gaz inflammables avec les soudeurs

MIG. Seuls les gaz inertes ou

ininflammables tels que le gaz

carbonique, l’argon, l’hélium ou un

mélange d’un ou plus de ceux-ci

conviennent au soudage MIG.

Ne jamais

soulever

les bouteilles par leurs soupapes,

chapeaux ni avec les chaînes ou élingues.

AVERTISSEMENT

DANGER

AVERTISSEMENT

Généralités Sur La

Sécurité

(Suite)

WG4000

Installation

3. Installer la fixation avec les cinq vis

retirées à l’étape 1.

MONTAGE DE LA PINCE DE TRAVAIL

1. Desserrer les écrous hex. sur la pince

de travail.

2. Insérer le cordon par la poignée de

pince et glisser le fil nu sous le bloc

de fixation. Resserrer les écrous

hexagonaux en vous assurant que les

fils nus soient bien pincés (Figure 3).

Collier De Mise A La Terre

1. Desserrer le boulon hexagonal ou

l’écrou sur le collier de mise à la

terre.

2. Introduire le cordon à travers le

manche du collier et glisser le fil nu

sous le bloc du collier. Serrer le

boulon hexagonal en s’assurant que le

fil nu soit bien fixé (Figure 4).

Installation de Fils

La puis-

sance de

soudage peut être appliquée aux

bornes de sortie, rouleau entraîneur,

collier de mise à la terre, raccord du

câble de pistolet et le fil de soudage

même si l’interrupteur du pistolet n’est

pas activé. Ne pas toucher à ces pièces

quand le soudeur est en marche.

REMARQUE : Avant d’installer le fil à

soudage, s’assurer que le diamètre du

fil à soudage correspond à l’encoche

dans le rouleau d’entraînement du

AVERTISSEMENT

20 Fr

Figure 4 - L’Enfilement du Fil

à Soudage

Collier de

serrage

Figure 3 - Montage du Collier de Mise

à la Terre

Pied avant

Chaîne et fixation de cylindre

Pince de travail

Régulateur, tuyau et brides de serrage

Bobine dévideuse de soudage à fil

fourré de .035 po (0,9 mm)

MONTAGE DE ROUE ET D’ESSIEU

1. Mettre une roue à chaque extrémité

de l’essieu. Utiliser un maillet ou un

marteau, enfoncer un moyeu de

plastique sur les extrémités de

l’essieu pour fixer les roues en place.

2. Aligner les trous sur le montage de

l’essieu avec les trous dans la plaque

de base à l’arrière du soudeur. Fixer

avec deux boulons, rondelles et écrous.

MONTAGE DU PIED

1. Retirer quatre vis dans le panneau du

bas près de l’avant du soudeur.

2. Aligner les trous du pied de métal

avec les trous au bas du soudeur à

l’avant.

3. Fixer le pied avec quatre vis retirées à

l’étape 1.

MONTAGE DE LA FIXATION DU

CYLINDRE

1. A l’arrière du soudeur, se trouvent

deux vis à moitié chemin de chaque

côté. Retirer les deux paires de vis et

retirer la vis au centre du panneau

arrière.

2. Insérer la fixation du cylindre entre

les côtés du soudeur et son arrière

noir en alignant ses trous avec ceux

des côtés du soudeur. S’assurer que la

fixation ait les fentes de la chaîne

vers le haut.

d’espace de ventilation devant et

derrière du modèle. Garder l’espace

de ventilation libre d’obstructions.

● Entreposer les fils dans un endroit

propre et sec à basse humidité afin

de conserver le fini du fil.

● Le récipient utilisé pour le soudeur

doit être mis à la terre correctement

et le soudeur doit être le seul

appareil de charge sur le circuit

● Utiliser une rallonge n’est pas

recommandé pour les soudeurs

électriques à l’arc. La perte de

tension dans la rallonge peut

réduire le rendement du soudeur

Modèle WG4000

Les pièces détachées du soudeur

indiquées ci-dessous se trouvent

dans le compartiment d’entraîne-

ment de fils. Ouvrir et retirer.

Outils nécessaires

Tourne-écrou 1/4 po (6,4 mm), 9/32 po

(7,1 mm), 5/16 po (7,9 mm)

Tournevis #2 Phillips

Maillet ou marteau

Après avoir déballé le soudeur, vous

trouverez une boîte à l’avant entourant

le chalumeau, le fil de la borne agrafe

et le cordon.

La boîte à l’arrière du soudeur contient

des pièces à assembler.

Roues (2), essieu (1), moyeu de

plastique (2), boulons d’essieu (2),

écrous (2) et rondelles (2)

Montage

Figure 2 - WG4000 Assembly

Boulon

Rondelle

Écrou

Arbre de

roue

Moyeu de

plastique

Roue

Montage

de pied

Boulon

Chaîne de

cylindre

Fixation de

cylindre

Écrou hexagonal

Cordon

Soudeur À L’Arc Alimenté En Fil

Installation (Suite)

La page charge ...

Campbell Hausfeld WG4000 Manuel utilisateur

Marque: Campbell Hausfeld

Modèle: WG4000

Catégorie: Système de soudage

Taper: Manuel utilisateur

Ce manuel convient également à

Welder WG4000

Télécharger le PDF

rapport

dans d''autres langues

English: Campbell Hausfeld WG4000 User manual
español: Campbell Hausfeld WG4000 Manual de usuario

Campbell Hausfeld WG4000 Manuel utilisateur

Ce manuel convient également à

Campbell Hausfeld WG4000 Manuel utilisateur

dans d''autres langues

Documents connexes