Powerfist 8622946 Le manuel du propriétaire

V 4.3 8622946

Please read and understand all instructions before use. Retain this manual for

future reference.

User Manual

196cc Plate Compactor

8622946 196cc Plate Compactor V 4.3

2 For technical questions call 1-800-665-8685

SPECIFICATIONS

Compacting Plate Dimensions (LxW) 20-7/8 x 14-5/8 in.

Vibrations/Minute 5,500 VPM

Travel Speed 82 ft/min

Compaction Force 2,473 lb

Compaction Depth 9-3/4 in.

Compaction Area/Hour 6,002 sq. ft

Water Tank Volume 3.7 gallons (14 litres)

Operation Weight 139 lb (63 kg)

INTRODUCTION

The 196cc plate compactor is designed to compact granular soils, crushed aggregate,

asphalt, paving stones, bricks and other materials. Ideal for smaller jobs like trenches,

retaining walls and other tight areas that don't require as much compaction.

The plate compactor comes with a 3.7 gallon water tank with spray bar for use on

asphalt and to help control dust. The paving pad prevents the compactor from

damaging or scuffing concrete pads, paving stones, bricks etc. The folding wheel kit

simplifies the task of moving the compactor around the jobsite and the handle folds

down for easy storage.

A separate engine manual is included. Please consult it when necessary.

SAFETY

WARNING! Read and understand all instructions before using this tool. The

operator must follow basic precautions to reduce the risk of personal injury

and/or damage to the equipment.

196cc Plate Compactor

V 4.3 196cc Plate Compactor 8622946

Visit www.princessauto.com for more information 3

Keep this manual for safety warnings, precautions, operating or inspection and

maintenance instructions.

HAZARD DEFINITIONS

Please familiarize yourself with the hazard notices found in this manual. A notice is

an alert that there is a possibility of property damage, injury or death if certain

instructions are not followed.

DANGER! This notice indicates an immediate and specific hazard that will result in

severe personal injury or death if the proper precautions are not taken.

WARNING! This notice indicates a specific hazard or unsafe practice that could

result in severe personal injury or death if the proper precautions

are not taken.

CAUTION! This notice indicates a potentially hazardous situation that may result

in minor or moderate injury if proper practices are not taken.

NOTICE! This notice indicates that a specific hazard or unsafe practice will

result in equipment or property damage, but not personal injury.

WORK AREA

1. Operate in a safe work environment. Keep your work area clean, well lit and

free of distractions.

2. Keep anyone not wearing the appropriate safety equipment away from the

work area.

3. Store unused tools properly in a safe and dry location to prevent rust or

damage. Lock tools away and keep out of the reach of children.

4. Do not install or use in the presence of flammable gases, dust or liquids.

PERSONAL SAFETY

WARNING! Wear personal protective equipment approved by the Canadian

Standards Association (CSA) or American National Standards Institute (ANSI).

PERSONAL PROTECTIVE EQUIPMENT

1. Always wear impact safety goggles that provide front and side protection for

the eyes. Eye protection equipment should comply with CSA Z94.3-07 or ANSI

Z87.1 standards based on the type of work performed.

8622946 196cc Plate Compactor V 4.3

4 For technical questions call 1-800-665-8685

2. Wear gloves that provide protection based on the work materials or to reduce

the effects of tool vibration.

3. Wear protective clothing designed for the work environment and tool.

4. Non-skid footwear is recommended to maintain footing and balance in the

work environment.

5. Wear steel toe footwear or steel toe caps to prevent a foot injury from

falling objects.

6. Wear a NIOSH approved respirator when working on materials that produce

hazardous fumes, dust or particulate matter.

7. This tool can cause hearing damage. Wear hearing protection gear with an

appropriate Noise Reduction Rating to withstand the decibel levels.

PERSONAL PRECAUTIONS

Control the tool, personal movement and the work environment to avoid personal

injury or damage to tool.

1. Do not operate any tool when tired or under the influence of drugs, alcohol or

medications.

2. Avoid wearing clothes or jewelry that can become entangled with the moving

parts of a tool. Keep long hair covered or bound.

3. Do not overreach when operating a tool. Proper footing and balance enables

better control in unexpected situations.

4. Securely hold this tool using both hands. Using a tool with only one hand can

result in loss of control.

SPECIFIC SAFETY PRECAUTIONS

WARNING! DO NOT let comfort or familiarity with product (gained from repeated

use) replace strict adherence to the tool safety rules. If you use this tool

unsafely or incorrectly, you can suffer serious personal injury.

1. Use the correct tool for the job. This tool was designed for a specific function.

Do not modify or alter this tool or use it for an unintended purpose.

2. Do not operate the tool if the safety guards are missing.

3. Do not allow anyone to stand next to the plate compactor while it is in

operation. The compactor’s plate can cause a serious injury.

V 4.3 196cc Plate Compactor 8622946

Visit www.princessauto.com for more information 5

4. Before operation, the operator has to be made familiar with the necessary

safety precautions and operating techniques.

5. All users must understand the operation of all controls and learn how to stop

the engine quickly in case of emergency.

a. Become familiar with the machine’s controls and all the caution, warning and

danger decals affixed to the machine before attempting to start or operate.

6. The engine and exhaust are hot during operation. Severe thermal burns can

occur on contact, especially with the muffler.

a. Remove accumulated debris from the muffler and cylinder area.

Combustible debris, such as leaves, grass, brush, etc. can catch fire if

they come in contact with a hot engine.

b. Do not place anything on the engine while it is running.

c. Allow the muffler, engine cylinder and fins to cool before touching grass-

covered or brush-covered unimproved land.

7. Always operate this equipment with all guard and safety devices in place.

Never operate this machine if any guard or safety devices have been removed

or if they have malfunctioned.

8. Do not insert your hand or finger between the pulley cover and engine during

operation to avoid injury to your hand.

9. Never operate the plate compactor with the belt cover removed. The exposed

belt and pulley may cause serious injury when the tool is in use.

10. Never leave the machine unattended while running as it will move on its own.

Move the throttle lever to low gear and shut the plate compactor’s engine off

before leaving the area.

11. Do not use on steep slopes, as the tool can topple over

12. Never pick up or carry a machine while the engine is running.

13. If the unit strikes a foreign object, stop the engine, disconnect the spark plug,

thoroughly inspect the machine for any damage and repair the damage before

restarting and operating the machine.

14. Stay away from the edge of ditches and avoid actions that may cause the plate

compactor to topple over.

15. Do not operate on concrete or extremely hard, dry, compacted surfaces. The

plate will jump rather than vibrate and could damage both plate and engine.

8622946 196cc Plate Compactor V 4.3

6 For technical questions call 1-800-665-8685

VIBRATION PRECAUTIONS

1. This tool vibrates during use. Repeated or long-term exposure to vibration

may cause temporary or permanent physical injury, particularly to the hands,

arms and shoulders.

2. Anyone using vibrating tools regularly or for an extended period should first be

examined by a doctor and then have regular medical check-ups to ensure

medical problems are not being caused by or worsened from tool use.

3. If you feel any medical symptoms related to vibrations (such as tingling,

numbness and white or blue fingers), seek medical attention as soon as possible.

4. DO NOT use this tool if one of the following applies:

a. Pregnant

b. Impaired blood

circulation to the hands

c. Past hand injuries

d. Nervous system disorders

e. Diabetes

f. Raynaud's Disease

5. Do not smoke while operating the tool. Nicotine reduces the blood flow to the

hands and fingers, increasing the risk of vibration-related injury.

6. Wear suitable gloves to reduce the effects of vibration.

7. Use the tool with the least amount of vibration, when there is a choice between

different processes.

8. Do not use for extended periods. Take frequent breaks when using this tool.

9. Let the tool do the work. Grip the tool as lightly as possible (while still keeping

safe control of it).

10. To reduce vibrations, maintain the tool as explained in this manual. If abnormal

vibrations occur, stop using this tool immediately.

CARBON MONOXIDE POISONING

WARNING! Never start or run this engine indoors as exhaust contains carbon

monoxide gas. Opening windows and doors is not enough to ventilate the area.

Carbon monoxide is a colourless and odourless gas that is difficult to detect.

Carbon monoxide poisoning results from inhalation of the gas and may be lethal if

left untreated. Evacuate all people to an area with clean air and seek immediate

medical attention for any person experiencing the following symptoms:

V 4.3 196cc Plate Compactor 8622946

Visit www.princessauto.com for more information 7

1. Headache

2. Confusion

3. Shortness of breath

4. Weakness

5. Fatigue

6. Dizziness

7. Unstable gait (stumbling around)

8. Nausea and vomiting

9. Unconsciousness

10. Flu-like symptoms without fever

UNPACKING

WARNING! Do not operate the tool if any part is missing. Replace the missing

part before operating. Failure to do so could result in a malfunction and

personal injury.

Remove the parts and accessories from the packaging and inspect for damage.

Make sure that all items in the parts list are included.

Contents:

• Plate Compactor Chassis

• Handle

• Folding Wheels Kit

• Paving Pad Kit

• Hardware: bolts, washers and nuts.

IDENTIFICATION KEY

A Throttle Control

B Upper Handle

C Lower Handle

D Muffler

E Air Cleaner

F Fuel Tank

G Engine

H Belt Guard

I Vibrator

J Base Plate

K Oil Drain Hose

L Water Tank (not shown)

Fig. 1

8622946 196cc Plate Compactor V 4.3

8 For technical questions call 1-800-665-8685

ASSEMBLY & INSTALLATION

When this manual refers to a part number, it refers to the included Parts

Identification section.

1. Unfold the handle (Fig. 2).

2. Mount the handle. Fit the handle ends into the channels on the engine deck.

Place flat washers 10, followed by hex bolts M10 x 65 on the outer side.

Tighten with lock nuts M10 on the inner side (Fig. 3).

3. Secure the throttle

control onto the upper

handle with a flat

washer 5 and a bolt 5

x 25 (Fig. 3).

4. Fasten the throttle

control cable with

cable fasteners. Line

up the holes in the link

plates and engine

deck. Slide bolts

M10 x 30 through the

holes from one side,

then lock nuts M10

from the other side

and tighten (Fig. 4)

5. Before compacting,

fold the wheels up

(Fig. 5).

Fig. 2

Fig. 3

Fig. 4

Fig. 5

V 4.3 196cc Plate Compactor 8622946

Visit www.princessauto.com for more information 9

PAVING PAD KIT

The transparent rubber paving pad allows the tool

to compact concrete paving slabs, stones, bricks

and blocks without marring their surface.

Attach the paving pad onto the base plate as

shown. Align the holes in the base plate, paving

pad and clamp plates. Secure it with lock washers

and M10 x 30 bolts (Fig. 6).

WATER TANK

Press the water tank into the opening at the

front of the machine. The tank center will fit

between the upright struts. Secure in place

before filling with water.

OPERATION

NOTICE! This tool ships without oil. Consult the engine manual on how to refill

the engine oil. See Lubrication section in this manual on how to fill the vibrator

with oil. Failure to fill engine or vibrator with oil before starting the engine will

result in permanent damage to the tool.

IMPORTANT! Before digging or compacting, contact your local utilities to

determine the location of buried pipes or cables.

The plate compactor can compact loose soil, sand, gravel, asphalt and broken concrete.

Soils with a high clay content are not recommended for compacting with this tool, but it

can be done with the proper technique (see Compacting High Clay Content Soil).

The tool vibrates the surface through the base plate, forcing the soil/gravel

into a smaller physical space. The surface material must be loose enough to

allow movement during compaction. Some surfaces may require preparation

before compacting.

A surface that is too hard can cause the tool to bounce instead of compact. This

may damage the tool or cause a vibration injury over time due to repeated

exposure. A bouncing plate compactor indicates the material is compact. Add

another layer of material if building up a compacted area.

Fig. 6

Fig. 7

8622946 196cc Plate Compactor V 4.3

10 For technical questions call 1-800-665-8685

PREPARING THE SURFACE

1. Dry Surface – A dry surface will produce dust during compaction. Sprinkle

water over the soil and allow it to soak in, before resuming compaction. Only

sprinkle enough water on gravel to keep the dust down. This will extend the life

of the engine’s air filter.

2. Wet Surface – Soil that is too wet may stick to the base plate. The sticking soil

will then compact onto the tool and cause excess weight that can put more

stress on the engine. It will also prevent the proper compaction of the soil

surface. Dry the surface or wait until it is suitable for compaction.

3. Asphalt - Wet the asphalt surface and base plate of the tool to prevent the

asphalt from sticking during compaction. Dampen the surface and base plate

as needed. The compactor comes with a water tank and sprinkler system.

4. Stones/Broken Concrete – Remove large stones or chunks of concrete as the

compactor does not break these apart. Larger stones and broken concrete may not

compact as much as expected. Compaction is more effective with smaller objects.

5. Obstacles – A work site may have natural obstacles (stump, buried stones) or

manmade obstacles (construction waste, power cords or hoses) that will

interfere with the compacting process. Check the work area and remove all

obstacles before beginning compacting.

OPERATING THE PLATE COMPACTOR

The plate compactor is started with the throttle lever in low gear. The power

bypasses the centrifugal clutch and the base plate does not vibrate.

Once the throttle lever is opened, the base plate begins to vibrate. As the vibrator

rotary shaft rotates, the centrifugal force ‘throws’ the base plate forward. This

motion pulls the tool forward without effort. As the throttle lever is opened further,

the centrifugal force increases in strength and frequency. This results in deeper

compaction and the tool moves faster.

This unit can only travel forward. Plan your compacting route to allow forward

turns, if the compacting next to a structure such as a wall.

WARNING! Maintain a grip on the tool at all times when under power, as it will

move by itself when the throttle is open and may pose an injury risk to

bystanders and the operator.

V 4.3 196cc Plate Compactor 8622946

Visit www.princessauto.com for more information 11

1. Check the plate compactor before use (see Maintenance Chart - Daily

before operating)

a. Check the gasoline engine before use per the separate engine

instruction manual.

b. Attach the paving pad to the bottom of the plate when compacting paving

stones to prevent chipping or grinding the surface.

2. Position the throttle lever in low gear.

3. Start the gasoline engine per instructions in the engine instruction manual.

4. Hold the compactor handle and move the throttle lever towards high gear. The

vibrator assembly will engage and the compactor will begin to move forward.

5. Retain a hold of the handle and guide the tool as it compacts. Inclines may require

a gentle pressure to maintain forward momentum (see Compacting on an Incline).

6. Watch for obstacles in the tool’s work path that can create a dangerous hazard

or may damage the tool. Move the throttle lever to low gear and wait for it to

stop moving before removing the obstacle. Turn the tool off and move to a

safe location if the object will require more than a few seconds to remove.

7. The surface may require 3 or 4 passes to achieve full compaction. The type of

surface material will determine how many passes are needed. The tool will

begin to bounce when the material is compact.

8. Move the throttle lever to low gear once a pass is complete to disengage the

vibrator assembly. Reposition the tool for another pass and repeat steps 4 and 5.

9. Move the throttle lever to low gear once the job is complete and wait until the

tool stops vibrating. Shut the engine off per the engine instruction manual

instructions and allow it to cool.

a. Let the engine idle for several minutes before shutting it off if the compactor

was used for a length of time or the job was hard on the equipment. This will

allow a gradual cooling of the engine components without damage.

COMPACTING HIGH CLAY CONTENT SOIL

A dry intermediary material may be used to cover the soil surface to prevent the soil

from sticking to the compactor’s base plate.

1. To compact soil with a high clay content, reduce speed so the compactor’s base

plate is still vibrating, but not leaving the surface. This will require the operator to

push the compactor more to account for the loss of natural momentum.

8622946 196cc Plate Compactor V 4.3

12 For technical questions call 1-800-665-8685

2. Check underneath the base plate and remove all material that is stuck after

each pass or more often if required.

3. Double the number of passes to compact the soil as the plate compactor is not

at full power.

COMPACTING ON AN INCLINE

WARNING! Never stand below the plate compactor when using on an incline as

it may topple and cause a serious injury. When changing direction, always

remain uphill.

WARNING! Stop compacting immediately if the tool is difficult to control

on an incline. The tool may topple and cause a serious injury to the operator

or bystanders.

The incline cannot exceed a 20° angle. There may be a risk that the tool will

topple during compaction. The angle will also prevent the oil lubrication system

from operating correctly and damage the engine.

1. The best method of compacting on an incline is starting at the top and moving

down the incline.

2. Adjust the speed that the compactor moves with the throttle, until it is comfortable.

3. At the slope’s bottom, move the throttle to idle speed to stop the base plate

from vibrating.

4. Pull the plate compactor to the top of the incline and fully open the throttle to

start the base plate vibrating. Resume the soil compacting.

a. The wheel assembly will make it easier to pull the plate compactor up

the incline.

5. A shallow incline may allow compacting from side-to-side, moving down the

incline as each section is complete. In this case, compacting on an incline may

require the operator to lightly push the tool to maintain forward momentum.

CARE & MAINTENANCE

1. Maintain the tool with care. A tool in good condition is efficient, easier to

control and will have fewer problems.

2. Inspect the tool components periodically. Repair or replace damaged or worn

components. Only use identical replacement parts when servicing.

V 4.3 196cc Plate Compactor 8622946

Visit www.princessauto.com for more information 13

3. Follow instructions for lubricating and changing accessories.

4. Only use accessories intended for use with this tool.

5. Keep the tool handles clean, dry and free from oil/grease at all times.

6. Maintain the tool’s labels and name plates. These carry important information.

If unreadable or missing, contact Princess Auto Ltd. for replacements.

7. Have the plate compactor inspected at least once a year.

8. Consult the engine instruction manual for engine care and maintenance steps.

WARNING! Only qualified service personnel should repair the tool. An

improperly repaired tool may present a hazard to the user and/or others.

PREVENTATIVE MAINTENANCE

1. Turn off engine. Engine must be cool.

2. Keep the engine’s throttle lever in its SLOW position and remove spark plug

wire from spark plug and secure.

3. Inspect the general condition of the plate compactor. Check for loose screws,

misalignment or binding of moving parts, cracked or broken parts and any

other condition that may affect its safe operation.

4. Remove all debris from the plate compactor with a soft brush, vacuumor

compressed air. Then use a premium quality lightweight machine oil to

lubricate all moving parts.

5. Clean the bottom of the compactor base as soon as it begins to pick up soil

being compacted. The unit cannot do a good job if the bottom surface is not

smooth and clean.

6. Return spark plug wire.

Notice! Never use a pressure washer to clean your plate compactor. Water can

penetrate tight areas of the unit and cause damage to spindles, pulleys,

bearingsor the engine. The use of pressure washers will result in shortened life

and reduce serviceability.

CHECKING V-BELT(S)

To ensure optimum power transmission from the engine to the eccentric shaft, the

V-belt(s) must be in good condition and operate under proper tension.

1. Turn the engine off. The engine must be cool.

2. Remove the belt guard to access the V-belt(s).

8622946 196cc Plate Compactor V 4.3

14 For technical questions call 1-800-665-8685

3. Check the V-belt(s) condition. Replace any V-belt that is cracked, frayed or glazed.

4. Check the V-belt tension by squeezing them in the center. The normal

deflection on each side should be 9 to 13 mm (3/8 to 1/2 in.) with moderate

pressure from your thumb or finger.

IMPORTANT! On new machines or after installing a new belt, check belt tension

after firs 20 hours of operation. Check and adjust belt every 50 hours thereafter.

TENSIONING V-BELT(S)

Proper belt tension is critical to good performance. Proper adjustment will assure

long belt life. Too much or too little belt tension will cause premature belt failure.

1. Loosen the four engine mount bolts

without removing them.

2. Loosen the jam nuts (Fig. 8-2), but

do not remove them. Leave enough

space between the nut and bracket

to move the engine.

3. Push engine toward the back of

the plate.

4. Turning the adjustment bolts (Fig. 8-1) to remove any slack in V-belt(s).

IMPORTANT! When adjusting the

belt(s), make sure that the clutch

pulley (Fig. 9-2) is in alignment with

the vibrator pulley (Fig. 9-1).

5. When the V-belt tension is correct,

tighten the jam nuts (Fig. 8-2)

against the bracket.

6. Tighten the engine mount bolts.

7. Replace the belt guard.

Replace the belts when the adjustment bolts can no longer tension them.

Fig. 8

Fig. 9

V 4.3 196cc Plate Compactor 8622946

Visit www.princessauto.com for more information 15

REPLACING V-BELT(S)

Replace both V-belts. Work on one belt at a time.

1. Loosen the four engine mount bolts without removing them.

2. Loosen the jam nuts (Fig. 8-2) and bolts (Fig. 8-1).

3. Slide the engine toward the front of plate and slip the old V-belt(s) off of

the wheel pulley and install the new V-belt(s) in their place.

4. Position the V-belt(s) over the engine pulley.

5. Move the engine back.

6. When the V-belt tension is correct, tighten the jam nuts (Fig. 8-2) and the

engine mount bolts.

7. Replace the belt guard.

CLEANING

Do not use strong detergents or petroleum based cleaners when cleaning plastic

parts. Chemicals can damage plastics.

MAINTENANCE SCHEDULE

Maintenance Interval Maintenance Point

Daily before operating.

1. Check the fuel level.

2. Check the engine oil level.

3. Inspect the fuel lines.

4. Inspect the air filter and replace it if needed.

5. Check and tighten the external hardware.

After the first 20 operating hours.

1. Check and adjust the drive belt.

2. Change the engine oil.

After the first 50 operating hours

or every week.

1. Check and adjust the drive belt.

2. Clean the air cleaner element.

3. Change the engine oil.

4. Check and clean the spark plug.

After the first 100 operating hours

or every month.

1. Clean the fuel strainer.

Each 200 hours or every two months.

1. Replace vibrator fluid

After the first 300 operating hours

or every year.

1. Check and adjust the valve clearance.

2. Clean the cylinder head.

3. Change the lubrication oil.

8622946 196cc Plate Compactor V 4.3

16 For technical questions call 1-800-665-8685

LUBRICATION

Inspect and lubricate the tool when required. Use grease to lubricate the tool. Other

lubricants may not be suitable and could damage the tool or cause a malfunction

during use.

VIBRATOR SYSTEM LUBRICATION

The tool’s vibrator housing contains the vibrator rotary shaft that causes the base

plate to move. The vibrator housing contains extreme pressure oil to bathe the

rotary shaft during operation.

Use automatic transmission fluid to lubricate the vibrator housing.

REPLACING VIBRATOR SYSTEM OIL

1. Run tool briefly to mix and warm the oil.

2. Remove the belt guard and V-belt(s) (Fig. 10).

3. Remove the bolts that hold the deck to the housing

(Fig. 10).

4. Lift entire deck with engine from housing (Fig. 9).

5. Place a receptacle below the opening to catch the

waste oil.

6. Remove the plug on top of the vibrator housing. Tilt

the housing upside down so oil drains from the

vibrator (Fig. 11).

a. Examine oil for metal chips to determine if

further maintenance is needed.

7. Return plate housing to the upright position.

8. Fill the vibrator housing with 80 ml of gear oil API

GL-4 80W/90 or 75W/90.

9. Apply a pipe sealant to the plug and reinstall into the

vibrator housing.

10. Reattach the engine to the frame.

Fig. 10

Fig. 11

V 4.3 196cc Plate Compactor 8622946

Visit www.princessauto.com for more information 17

STORAGE

When not in use for an extended period, apply a thin coat of lubricant to the steel

parts to avoid rust. Remove the lubricant before using the tool again.

LONG-TERM STORAGE

In case of long period storage for more than 30 days:

1. Remove foreign objects such as loose stones and dirt from the plate

compactor and engine.

2. Consult the engine instruction manual and follow storage procedures in

that manual.

3. Use clean cloths to wipe down the compactor. Keep the air vents free of

obstructions.

4. Carefully fold the upper handle down. Do not allow control cables to become

pinched or bent.

5. Store the plate compactor upright in a clean, dry area. Cover it up with dry

cloth for storage.

TRANSPORTING

WARNING! Transport the plate compactor with an empty fuel tank or with the

fuel shut-off valve secured in the OFF position.

1. Allow the engine to cool before transporting to prevent burn injuries or a

fire hazard.

2. Do not attempt to load the plate compactor onto a vehicle by yourself. Use a

crane or additional people to assist in loading/unloading. The tool is heavy and

may cause a back injury.

3. Lift the unit by the handles on the front

and back of the frame (Fig. 12). Do not

hold the plate compactor by the handle

while loading as it may swing open and

cause an impact injury.

4. Secure the tool upright to prevent it from

moving or toppling over during

Fig. 12

8622946 196cc Plate Compactor V 4.3

18 For technical questions call 1-800-665-8685

transportation. The tool is heavy and can cause a crushing injury if it falls over

onto the user or a bystander.

5 Transport the tool in the upright position. Turn all valves to the OFF position.

Ensure all caps are in place and sealed tight to prevent spills if it should fall

over during transportation.

a. Remove fuel from the engine’s fuel tank when possible before transportation.

6. Do not transport with the engine’s spark plug facing down. Transporting with

the spark plug down will result in hard starting and/or engine smoking.

DISPOSAL

Recycle a tool damaged beyond repair at the appropriate facility.

Contact your local municipality for a list of disposal facilities or by-laws for

electronic devices, batteries, oil or other toxic liquids.

IMPORTANT! DO NOT pollute the environment by allowing uncontrolled

discharge of waste oil.

TROUBLESHOOTING

Visit a Princess Auto Ltd. location for a solution if the tool does not function properly or

parts are missing. If unable to do so, have a qualified technician service the tool.

Problem(s) Possible Cause(s) Suggested Solution(s)

Poor

performance

(plate compactor

does not develop

to its full speed).

1. The engine throttle is not

open fully.

2. The throttle lever is not set

correctly.

3. The ground is too wet for

compacting.

4. Drive belt is loose or worn

out and slips on pulleys.

5. Vibrating shaft bearings are

binding.

6. Air filter is clogged with dust,

reducing engine

performance.

7. The engine speed is too low.

1. Open the engine throttle completely.

2. Set the throttle lever.

3. Dry the soil before compacting.

4. Check whether the engine mounting

bolts are tight. Adjust or replace the

belt.

5. Check the oil condition and level in the

vibrator housing. Add/change the oil.

6. Clean or replace the air filter cartridge.

7. Check the engine speed with

tachometer and adjust the engine to

run at correct speed. Refer to the

engine instruction manual.

V 4.3 196cc Plate Compactor 8622946

Visit www.princessauto.com for more information 19

Problem(s) Possible Cause(s) Suggested Solution(s)

Engine is running

but not vibrating.

1. The engine throttle is not

opened.

2. Clutch is damaged.

3. Engine speed is too low.

4. The drive belt is loose or

broken.

1. Open engine throttle.

2. Replace the clutch.

3. Too much oil in the vibrator housing.

Adjust the oil level.

4. Adjust/replace drive belt.

Plate jumps or

compacts

unevenly.

1. The ground surface is too

hard.

2. Rubber isolator is loose or

damaged.

1. Wet soil or ground and allow to seep

in before compacting.

2. Adjust/replace the rubber isolator.

Slow travel speed

and weak

vibration.

1. Slow engine speed.

2. Clutch slips.

3. Drive belt slips.

4. Over-filling of vibrator oil.

5. Vibrator housing defect.

1. Reset the engine RPM appropriately.

2. Check and/or replace clutch.

3. Check and/or replace the drive belt.

4. Drain additional oil and maintain at

appropriate level.

5. Check eccentric vibrator, gear and

counterweight.

No forward

movement.

1. Drive belt slips.

2. Clutch slips.

3. Vibrator locks.

4. Piston or bearing defect in

cylinder.

1. Check and/or replace the drive belt.

2. Check and/or replace clutch.

3. Check the vibrator housing (eccentric

vibrator, gear and counterweight).

4. Replace worn piston or bearing in

cylinder.

Slow travel

speed.

Material stuck to base plate. Clean material from base plate.

8622946 196cc Plate Compactor V 4.3

20 For technical questions call 1-800-665-8685

PARTS BREAKDOWN

La page charge ...

Powerfist 8622946 Le manuel du propriétaire

Powerfist 8622946 Le manuel du propriétaire

dans d''autres langues

Autres documents